Batteries, Fuel Cells, and Energy Conversion
A1913
Toru Katakabe, Taketo Kaneko, Masayoshi Watanabe, Takanori Fukushima and Takuzo Aida
Single-walled carbon nanotubes (SWNTs) formed gels after being ground with a room-temperature ionic liquid (RTIL). The gels were used as electrodes of electric double-layer capacitors (EDLCs), and the RTIL was used as the electrolyte. The performance of the EDLCs was examined by charge-discharge experiments and was compared with that of the EDLCs using activated carbon electrodes and the RTIL electrolytes. The gels functioned as the electrodes over a wide composition range from 0.02 to 0.12 of SWNT/RTIL (wt/wt), and the retained capacitance increased with increasing the SWNT compositions. The EDLCs with the SWNTs showed higher capacitance than that with the activated carbons in terms of the capacitance per unit surface area, though the gravimetric capacitance was lower. The gel electrodes can be fabricated as thick as
without a severe ohmic-drop problem, which may contribute to a simple cell structure. The changes in the performance of the SWNT-EDLCs, with or without the gelation, were apparent, and the gelation greatly contributed to the high performance. This is due to the formation of continuous SWNT and RTIL paths at the molecular level by the gelation.
A1917
Tsutomu Ioroi and Kazuaki Yasuda
Platinum-iridium (Pt-Ir) alloy electrocatalysts for polymer electrolyte fuel cell (PEFC) cathodes were prepared, and their physical and electrochemical properties were examined. A variety of unsupported Pt-Ir alloy catalysts was prepared in hot KOH solution, and the obtained Pt-Ir alloy catalysts were aggregates of fine particles
; the structure of the alloy was a uniform solid solution phase between Pt and Ir. Evaluation of the activity for the oxygen reduction reaction (ORR) was performed by both the rotating disk electrode (RDE) method in 0.1 M
solution and determination of the specific activity during PEFC single-cell operations. The ORR kinetic analysis by the RDE showed that alloying Pt with Ir, especially with 5-20 wt % Ir, enhanced the catalytic activity for the ORR by a factor of more than 1.5 at 0.8 V vs RHE. The relationship between the specific current density and Ir content under PEFC operating conditions also showed enhanced ORR activity at 5-20 wt % Ir, which was consistent with the RDE results.
A1925
Pier Paolo Prosini
A1930
T. W. Farrell and C. P. Please
A mathematical model for the galvanostatic discharge of a porous manganese oxide particle, similar to those found within primary alkaline battery cathodes, is presented. Asymptotic techniques are employed to obtain the leading order spatial and temporal behavior of the particle. It is found that there is an initial rapid transient adjustment within the crystals forming the particle followed by a prolonged relatively uniform discharge regime which leads finally to a faster, particle-based, nonuniform discharge behavior. Analytical solutions of the model are obtained which describe the majority of the particle behaviors under a wide range of industrially relevant discharge conditions. These solutions are supplemented by simple numerical solutions where required. A comparison of the results with those obtained by a previous, more complete and accurate model is presented. The analysis shows that the particle radius, the applied discharge current, and the solid phase conductivity are the critical parameters that dictate the utilization of active material across a wide range of discharge conditions. The effect of these parameters on particle utilization is also presented.
A1942
Guangyu Lin and Trung Van Nguyen
The effect of thickness and wetproof level of the gas diffusion layer on electrode flooding and cell performance was investigated. Three types of gas diffusion media were tested: SGL SIGRACET carbon papers, with and without a microporous layer, and Toray TGPH carbon paper without a microporous layer. Overall, it was found that SGL carbon paper with the microporous layer gave the best fuel cell performance even at low air stoichiometries. It was also found that adding poly(tetrafluoroethylene) (PTFE) to the gas diffusion layer could enhance gas transport and water transport when a cell operates under flooding condition, but excessive PTFE loading could lead to a high flooding level in the catalyst layer. It is our opinion that a combination of hydrophobic pores for gas transport and hydrophilic pores for liquid water transport within the macroporous layer is needed. It is also our opinion that the optimal ratio of hydrophobic and hydrophilic pores depends on the pore size and its distribution. Finally, it was observed that without the microporous layer, thinner gas diffusion materials were more sensitive to liquid water accumulation than the thicker ones.
A1949
P. Reale, S. Panero and B. Scrosati
A1955
Yingchun Zhang, Yixuan Wang, Lawrence G. Scanlon and Perla B. Balbuena
A1963
Takeshi Sasaki, Soon-Ki Jeong, Takeshi Abe, Yasutoshi Iriyama, Minoru Inaba and Zempachi Ogumi
The effect of an alkyl dicarbonate, diethyl 2,5-dioxahexane dicarboxylate (DEDOHC,
), which is formed by an ester exchange reaction in a mix solvent system of ethylene carbonate (EC) and diethyl carbonate (DEC), on the performance of
lithium-ion cells was investigated. In the presence of 10 vol % DEDOHC in
, discharge capacity decreased, in particular at a high charge/discharge rate. Capacity retention at a high charge/discharge rate also decreased during repeated charge and discharge cycles. These deteriorations in performance were attributed to an increase in cell impedance and deficiency of mobile lithium ion, which is caused by continuous consumption of lithium ion on graphite negative electrode. The results of half-cell tests revealed that the addition of DEDOHC causes serious degradation for the graphite half-cell. From ac impedance measurements it was found that surface film resistance on graphite electrode was fourfold higher in the solution containing DEDOHC, whereas charge-transfer resistance scarcely changed. Atomic force microscopy observation revealed the formation of dense and highly adhesive surface precipitate layer on graphite electrode in the presence of DEDOHC. Consequently, it was concluded that the increase in cell impedance, which leads to deterioration of charge and discharge performance, is mainly due to the increase in the resistance of the surface film formed from the reduction of DEDOHC on the graphite negative electrode.
A1969
Xiao-Zhen Liao, Zi-Feng Ma, Yu-Shi He, Xiao-Ming Zhang, Liang Wang and Yi Jiang
A1974
J. Vatsalarani, D. C. Trivedi, K. Ragavendran and P. C. Warrier
Performance of porous zinc electrode in alkaline secondary battery systems suffers mainly from shape change and dendrite growth. Polyaniline coating in direct contact with porous zinc electrode was found to restrict zincate movement away from the test electrode, which otherwise may lead to a decrease in electrode surface area (shape change of the electrode) on repeated cycling. Constant current charge/discharge cycles of the blank and polyaniline-coated zinc electrodes have been carried out to assess the performance of the polymer film. It was found that a fibrous network of polyaniline coating allows
ions and restricts the diffusion of zincate ions.
A1979
Renjie Chen, Feng Wu, Hongying Liang, Li Li and Bin Xu
Binary room-temperature complex electrolytes have been synthesized based on lithium bis(trifluoromethane sulfone) imide [
, LiTFSI] and organic molecules with amide (acylamino) groups such as ethyleneurea, acetamide, etc. The thermal properties and electrochemical performances of the complex systems are evaluated with differential scanning calorimetry (DSC), ac impedance spectroscopy, cyclic voltammetry (CV), and in a test electric double layer capacitor, respectively. DSC analysis shows that the eutectic temperatures of most complex systems are below 0°C. The ionic conductivities of these complex systems exceed
at room temperature. Analysis of their CV behavior indicates that the electrochemical stability windows of these electrolytes are over 4 V. These complex systems prove to be promising candidates of electrolytes for supercapacitor and other electrochemical devices.
A1985
Yo Kobayashi, Shiro Seki, Mitsuharu Tabuchi, Hajime Miyashiro, Yuichi Mita and Toru Iwahori
A1989
Nicholas S. Ergang, Justin C. Lytle, Hongwei Yan and Andreas Stein
A1996
Xianming Wang, Hitoshi Naito, Yoshitsugu Sone, Go Segami and Saburo Kuwajima
We tested the effect of two new additives, cyclo hexane (CH) and 1-methyl-2-pyrrolidinone (NMP), on the cycling performance of a carbon-coated artificial graphite (AG) anode on a lithium-ion cell to investigate suppression of irreversible capacity loss of the graphite anode during the first-cycle charge. Both CH and NMP additives effectively increased the coulombic efficiency of the graphite anode during the first cycle. We attribute this phenomenon to the dissolution of the poly (vinylidene fluoride) (PVdF) binder of the AG anode due to CH or NMP addition, which improved the PVdF elasticity and reduced the contact area between the AG particles and the electrolyte. Consequently, adding CH or NMP reduced the loss of lithium ions in the first-cycle charge. Cycle-performance testing of the Li/AG half-cell indicated that we could achieve maximum discharge capacity and coulombic efficiency by applying an additive amount ranging from 2 to 5% for both CH and NMP. The cycling performance testing of the
half-cell suggested that these two additives also have good oxidation stability and are therefore worth applying in lithium-ion cells with graphite anodes.
A2002
Venkat R. Subramanian, Vinten D. Diwakar and Deepak Tapriyal
In this paper, efficient approximate solutions are developed for microscale diffusion inside porous electrodes. Approximate solutions developed for the microscale diffusion are then coupled with governing equations for the macroscale to predict the electrochemical behavior of a lithium-ion cell sandwich. Approximate solutions developed facilitate the numerical simulation of batteries by reducing the number of differential algebraic equations resulting from the discretization of governing equations.
A2009
The following article is Free article
Arnold M. Stux and Karen E. Swider-Lyons
A2017
Jeff N. Soderberg, Aislinn H.C. Sirk, Stephen A. Campbell and Viola I. Birss
A2023
Franco Bonino, Sergio Brutti, Michele Piana, Bruno Scrosati, Luigi Brambilla, Giorgio Fustella, Chiara Castiglioni, Giuseppe Zerbi, Daniela Zane, Thierry Renouard et al
A low-temperature pyrolytic stepwise method is proposed to produce substantial amount of a carbonaceous material, characterized by a graphenic structure. The pyrolyzed material has been submitted to ballmilling steps of different times, and the samples obtained were studied from their structural and electrochemical points of view. The crystallographic data have evidenced crystallites with a crystal domain size less than one nanometer and the grinding influence is discussed. Electrochemical experiments have been carried out in order to study the mechanism of the Li insertion/deinsertion process in the host material. Interesting values of Li specific capacity have been calculated from cycle experiments in Li coin cells at constant current and a test in a Li-ion laboratory-type cell is proposed.
A2030
Yan-Yu Liang, Shu-Juan Bao, Ben-Lin He, Wen-Jia Zhou and Hu-Lin Li
A new low-temperature synthetic route has been developed and demonstrated for the production of spinel
as a cathode material for Li-ion batteries. The process involves the insertion of lithium into electrolytic manganese dioxide with glucose as a mild reductant in an autoclave. The material resulting from hydrothermal treatment is a spinel-structured
with reasonable crystallinity. It exhibits promising electrochemical behavior in nonaqueous liquid electrolyte. The influence of hydrothermal temperature and the effect of glucose in determining the final structural integrity and electrochemical performance have also been systemically explored. Furthermore, the capacity degradation of low-temperature synthesized spinels was studied by cyclic voltammetry and X-ray diffraction. This capacity fading can be mainly attributed to the factors of structural degradation and loss of active materials.
A2035
Tatsumi Ishihara, Satoko Fukui and Hiroshige Matsumoto
A2040
Liliya A. Dunyushkina and Stuart B. Adler
A2046
Takeshi Sasaki, Takeshi Abe, Yasutoshi Iriyama, Minoru Inaba and Zempachi Ogumi
Two methods were developed to suppress the formation of alkyl dicarbonate in Li-ion cells. One is the addition of vinylene carbonate (VC), which is vulnerable to nucleophilic attack, into the electrolyte to trap alkoxide anions that promote an alkyl dicarbonate formation. The addition of VC into the electrolyte of practical
prismatic cells effectively suppressed an alkyl dicarbonate formation and gave better cycle and power performance. The other method is a surface treatment of graphite to reduce the concentration of phenolic groups that were directly bonded to the graphite edge plane. The mild burn-off treatment successfully decreased the oxygen concentration on graphite surface and effectively suppressed an alkyl dicarbonate formation in the electrolyte. However, the irreversible capacity increased significantly, which was considered to be due to a change in the surface morphology of graphite by the burn-off treatment.
A2051
R. A.H. Niessen and P. H.L. Notten
The effect of reference electrode (RE)-induced surface poisoning of magnesium–scandium (MgSc) thin-film electrodes has been investigated. A comparison is made between various electrochemical responses of identical MgSc thin-film electrodes. The measurements were performed in two separate three-electrode setups containing REs from different manufacturers, the first of which contained a radiometer
RE that consists of a glass construction. The second setup contained a
RE from Koslow Scientific Company, which has a polyethylene housing. It was found that lead (Pb) species originating from the radio meter RE readily dissolves into the alkaline electrolyte. These dissolved species could be deposited on the surface of thin film electrodes, both as metallic Pb and Pb oxides, during electrochemical hydrogen loading/unloading of the MgSc alloys. This surface poisoning prohibits accurate determination of kinetic parameters related to the hydrogen adsorption reaction. The electrochemical measurements showed inferior electrode kinetics when using a radiometer RE as compared to a Koslow RE. The electrode kinetics could be linked directly to the amount of Pb deposited on the metal hydride thin film by means of electrochemical impedance spectroscopy and analytical techniques.
A2058
K.-F. Chiu, H. C. Lin, K. M. Lin and C. H. Tsai
Thin films of lithium manganese oxides were deposited by radio frequency magnetron sputtering. Negative electric bias was applied on the substrates during deposition. The deposited films exhibited a defected spinel structure,
, as characterized by X-ray diffraction and micro-Raman spectroscopy. As the substrate bias increased, the films developed stronger (111) orientation. At high substrate bias, the films tended to lose lithium and a second phase of manganese oxide developed. Postanneal was also carried out to fabricate well-crystallized
spinel thin films for comparison. The film morphology also varied with substrate bias as observed by scanning electron microscope. By substrate bias and anneal, well-crystallized films with different morphologies can be obtained. Charge–discharge and cyclic voltammetry curves of these thin films were measured and compared. The different electrochemical characteristics of these films were attributed to the modified crystallography, morphology, and film stress. The films deposited with in situ substrate bias exhibited larger capacity without well-defined plateau. The postannealed films without substrate bias showed well-defined 4.1 and 3.9 V plateaus with slightly lower capacity. The biased and annealed films had low capacity but showed only 3.5% of capacity loss after 30 cycles.
A2063
Jeng-Kuei Chang and Wen-Ta Tsai
Amorphous, hydrous manganese oxide was prepared by anodic deposition in manganese acetate solution. The effect of heat-treatments (up to 600°C) on the material characteristics of the oxides was investigated. The results indicated that the as-deposited oxide, which was fully amorphous, was transformed into a fibrous shape with nanocrystallinity after annealing at 200°C for 2 h.
and
were formed within the nanocrystalline oxide when heating at 400°C. Furthermore, by increasing the temperature over 500°C, the spherical
particles became the only phase present. In addition, atomic force microscopy was also carried out to explore the surface morphology of the oxide electrodes. This characterization method recognized condensation, rearrangement, reconstruction, and growth of the deposited manganese oxide as a function of temperature. The corresponding electrochemical performances of the oxides were evaluated by chronopotentiometry. The pseudocapacitive characteristics, reversibility, and cyclic stability of the deposited manganese oxide were improved by introducing the proper heat-treatment. However, high-temperature
heat-treatment promoted the formation of crystalline
and
and consequently resulted in the loss of the pseudocapacitive property of the oxides.
A2069
Guoying Zhang and Jun Chen
Perovskite-type
nanotubes were prepared by a sol-gel template method. The composition, morphology, structure, microstructure, and surface properties of the as-prepared products were characterized by inductively coupled plasma emission spectroscopy, scanning electron microscopy, X-ray diffraction, transmission electron microscopy and high-resolution transmission electron microscopy, and Brunauer–Emmett–Teller nitrogen adsorption–desorption measurements. The as-prepared nanotubes were used as the catalysts in the air electrode for oxygen evolution, exhibiting superior catalytic activity and durability in comparison with that of the electrodes made by nanoparticles. This is promising for the
nanotubes as electrocatalysts of air electrodes in fuel cells and rechargeable metal–air batteries. Furthermore, the
nanotubes were made into sensors and the sensitivity to hydrogen and ethanol was also measured, showing the tube interest in the application of gas sensors due to the nanostructure with interconnected hollow behavior.
A2074
Frank S. Baumann, Jürgen Fleig, Mitsuharu Konuma, Ulrich Starke, Hanns-Ulrich Habermeier and Joachim Maier
It is shown that the electrochemical resistance of mixed conducting solid oxide fuel cell (SOFC) model cathodes can be reduced drastically by a short but strong dc polarization of the cell. The samples investigated are dense thin-film microelectrodes of
on a yttria-stabilized zirconia solid electrolyte. Relative performance improvements of more than two orders of magnitude can be achieved with a cathodic dc bias of the order of 1 V, applied for a few minutes at fuel cell operating temperature. The positive effect on the electrode performance corresponds to an acceleration of the oxygen surface exchange reaction, initially the resistance determining process. For this surface-related resistance, absolute values as low as
at 700°C have been obtained. After such an activation, the resistance slowly increases again on a much larger time scale, indicating the possibility of a steady performance enhancement by a periodic activation with short dc pulses. X-ray photoelectron spectra show that a strong cathodic polarization severely changes the cation concentrations within the outermost surface layer of the electrode, and these field-induced surface compositional changes are assumed to be the main cause of the performance improvement.
A2080
S. Moravcová and K. Bouzek
The process of polypyrrole (PPy) embedding on the surface of a Nafion membrane was studied. The diffusion method was used for synthesis of the composite. An attempt was made to incorporate Nafion chains instead of sulfate into the PPy film as a counterion. The prepared composites were characterized with respect to their permeability to a monomer and methanol. Compared with a self-standing Nafion membrane, the permeability of the composite is reduced by several orders of magnitude. The incorporation of Nafion into the PPy film resulted in enhanced composite permeability to methanol. It can, therefore, be used to a limited extent to tune its properties. This may be of great importance in a potential application of this composite in polymer electrode membrane fuel cells as an alternative membrane electrode assembly.
A2089
Mariko Miyachi, Hironori Yamamoto, Hidemasa Kawai, Tomoyuki Ohta and Masato Shirakata
The chemical structure of SiO (silicon monoxide) anodes has been analyzed using X-ray photoelectron spectroscopy (XPS). Vapor deposition was used to form SiO anodes on Cu film. XPS analysis was performed on anodes at each of three stages: after deposition, after initial charge, and after discharge. The results of this analysis were then evaluated in terms of the anode’s respective electrochemical characteristics. It has been found that some Si remains oxidized in the full charge state and that lithium silicates are formed. The lithium silicates serve as a buffer with respect to changes in anode volume.
A2092
I. A. Schneider, H. Kuhn, A. Wokaun and G. G. Scherer
Corrosion, Passivation, and Anodic Films
B389
Roland De Marco, Zhong-Tao Jiang, Bobby Pejcic and Eddy Poinen
An in situ surface study of the carbon dioxide corrosion of mild steel has been undertaken using the tandem technique of mixed potential/synchrotron radiation-grazing incidence X-ray diffraction (SR-GIXRD). Long-term monitoring of the mixed potential showed there was an initial shift toward cathodic potentials attributable to preferential suppression of the cathodic half-reaction (viz., the reduction of carbonic acid), probably due to the formation of an adlayer of corrosion product physically blocking the cathodic reaction sites during the uniform corrosion of mild steel. Subsequently, the mixed potential displayed a gradual shift to anodic potentials, symbolizing the preferential suppression of the anodic half-reaction as the primary corrosion products [viz.,
,
,
, and
] acquired a sufficient thickness to physically block the interface against further corrosion. Nevertheless, the corrosion product continues to grow over time, indicating that the corrosion product is discontinuous and porous, allowing the ingression of electrolyte to enable the further corrosion of the mild steel. This research has important ramifications for the field of corrosion research; it should enable researchers to develop improved methods of chemical inhibition by using compounds that can actually bind to the newly postulated corrosion products on mild steel.
B393
X. Zhou, G. E. Thompson, J. Robinson and P. Skeldon
B397
D. Bengtsson Blücher, J-E. Svensson and L.-G. Johansson
The effect of part per billion (ppb) levels of
on the atmospheric corrosion on Al (99.999%) was investigated in the laboratory at 22°C. Exposure time was 20 and 672 h. The effect of
concentration (46-1300 ppb), relative humidity (70-99% RH), and the amount of NaCl applied prior to exposure
was studied. In addition, the effect of
and
on the
deposition rate was addressed. The samples were investigated by gravimetry, grazing incidence X-ray powder diffraction, ion chromatography, optical microscopy, and environmental scanning electron microscopy equipped with energy-dispersive X-ray fluorescence.
accelerates the atmospheric corrosion of Al, forming corrosion product “islands” containing aluminum hydroxy sulfate. Combining NaCl and
has a synergistic effect on the average corrosion rate. In contrast, the chloride-induced pitting of aluminum is significantly reduced by
. The corrosivity of
is attributed to the acidification of the surface electrolyte that destabilizes the alumina passive film. The suppression of pitting corrosion by
is attributed to the formation of aluminum hydroxy sulfates that are less soluble than the corresponding chlorides and slows down pit propagation. At relative humidities above 70% RH, there is a measurable steady-state deposition of
that corresponds to the rate of formation of sulfate. The
deposition rate is not limited by the oxidation of (IV)-valent sulfur on the surface.
deposition is enhanced by sodium chloride because the corrosion reactions in the NaCl(aq) electrolyte result in high pH in the cathodic regions and the formation of aluminum hydroxide. Ozone in the ppb range has only transient effects on the
deposition rate, whereas ppb levels of
had no effect at all.
B405
L. V. Taveira, J. M. Macák, H. Tsuchiya, L. F.P. Dick and P. Schmuki
B411
Xiaowei Zhao, Peng Jiang, Sishen Xie, Lifeng Liu, Weiya Zhou, Yan Gao, Li Song, Jianxiong Wang, Dongfang Liu, Xinyuan Dou et al
B415
Frederic Bernard, V. Shankar Rao and Hyuk-Sang Kwon
B421
F. Montilla, E. Morallón and J. L. Vázquez
B428
E. M. Sherif and Su-Moon Park
Inhibition of copper corrosion by
-phenyl-1,4-phenylenediamine (NPPD) has been investigated in deaerated, aerated, and oxygenated aqueous 3.0% NaCl solutions using potentiodynamic polarization, electrochemical impedance spectroscopy, weight loss, infrared and UV-visible absorption spectroscopic, scanning electron microscopic (SEM), and energy-dispersive X-ray (EDX) measurements. Potentiodynamic polarization measurements showed that the presence of NPPD significantly decreases cathodic, anodic, and corrosion currents in these solutions. Impedance measurements indicated that the charge-transfer resistances increase upon increasing the NPPD concentration. The inhibition efficiency of
NPPD obtained by weight-loss measurements is about 90%, increasing to about 96% at its concentration of
. Fourier transform infrared, UV-visible, SEM, and EDX measurements revealed that NPPD is adsorbed on the copper surface at open-circuit potentials, preventing copper from being corroded by forming a protective layer on its surface. All these results showed that corrosion of copper decreases in the order of
solutions, and NPPD is a good mixed-type inhibitor for copper corrosion with its inhibition efficiency in the order of
solutions.
Electrochemical/Chemical Deposition and Etching
C645
Jong-Min Lee and Alan C. West
A quasi one-dimensional current-distribution model is used to explore the impact of pulse-reverse plating parameters on throwing power when depositing copper into high-aspect-ratio through-holes or vias. The optimum waveform depends on a number of parameters, including bath composition, fluid flow, time-average plating rate, and via or through-hole dimensions. Understanding whether spatial variations in plating rate are caused primarily by electrical potential variations or by concentration variations is crucial to the design of a waveform. Pulse-reverse plating frequently provides greater improvements in throwing power than on-off pulse plating. Furthermore, employment of a pulse-reverse waveform can reduce the sensitivity of the throwing power to diffusion-layer thickness, a practically useful result when it is difficult to transfer a fluid-mixing method from the laboratory to manufacturing.
C652
Alan C. West, Ingrid Shao and Hariklia Deligianni
Numerical simulations are employed to demonstrate the daunting challenges involved in utilizing electrochemical polishing technologies as an alternative to low-down-force chemical mechanical planarization. Results show that small-aspect-ratio topographical features sitting on a relatively thin overburden are impossible to planarize by conventional electropolishing. Electrochemical mechanical planarization (E-CMP), where an anodic dissolution process is coupled with a polishing pad, is a more viable approach. Numerical simulations are compared to results obtained by E-CMP as a means of establishing an effective diffusion-layer thickness and as further demonstration of the infeasibility of electropolishing.
C657
Shou-Yi Chang, Ting-Kui Chang and Yu-Shuien Lee
C664
Xueru Zhang, Yufeng Hao, Guowen Meng and Lide Zhang
Highly ordered near-stoichiometrical polycrystalline InSb nanowire arrays have been fabricated by direct current (dc) electrodeposition inside the nanochannels of anodic alumina membranes (AAMs) and subsequent annealing. X-ray diffraction patterns and X-ray energy dispersion analysis reveal the change of crystal structure and the ratio of indium to antimony due to the deposition potential. The results show that cubic-phase InSb nanowire arrays can be achieved by using certain deposition potential and subsequent annealing. Transmission electron microscopy and scanning electron microscopy results demonstrate that these InSb nanowires are uniform with diameters about
, corresponding to the pore diameter of the AAMs. Raman spectrum further demonstrates the InSb nanowire with high crystal quality.
C669
Guofeng Cui, Ning Li, Deyu Li and Minglei Chi
The two mechanisms of phosphorus incorporation with nickel in electroless plating nickel are studied using X-ray fluorescence spectrometer (XRF) and cyclic voltammetry (CV). The results of XRF and CV data on the effect of single and double complexing agents on deposition rate and deposit composition indicate that nickel chelates can catalyze phosphorus generation, i.e., the mechanism of interface complex heterocatalysis on phosphorus incorporation with nickel. Furthermore, the choice principle to complexing agents for low-phosphorus electroless nickel bath was proposed based on it. Additionally, the direct mechanism of phosphorus generation can explain how single sodium hypophosphite can be reduced on nickel substrate on the CV curve. Finally, the optimal condition for low-phosphorus electroless nickel plating baths was determined. The experimental results support the explanation of the proposed mechanism.
C675
E. R. Parker, B. J. Thibeault, M. F. Aimi, M. P. Rao and N. C. MacDonald
Titanium is a promising new material system for the bulk micromachining of microelectromechanical (MEMS) devices. Titanium-based MEMS have the potential to be used for a number of applications, including those which require high fracture toughness or biocompatibility. The bulk titanium etch rate,
mask etch rate, and surface roughness in an inductively coupled plasma (ICP) as a function of various process parameters are presented. Optimized conditions are then used to develop the titanium ICP deep etch (TIDE) process. The TIDE process is capable of producing high aspect ratio structures with smooth sidewalls at etch rates in excess of
, providing a new means for the microfabrication of titanium-based MEMS devices.
C684
Zenglin Wang, Shoso Shingubara, Hiroyuki Sakaue and Takayuki Takahagi
A continuous electroless-plated Cu film only 10 nm thick was successfully deposited on a TaN barrier over a 1-nm-thick Pd catalytic layer formed by ionized cluster beam deposition. Secondary ion mass spectrometry (SIMS) analyses for the electroless-plated Cu films on the 20-nm and 1-nm ionized cluster beam (ICB)–Pd layers showed that the Pd metal had diffused into the Cu and caused a high electrical resistivity of Cu interconnect. The electrical resistivity of Cu interconnects formed by electroless plating on an ICB-deposited Pd catalyst layer decreased with decreasing thickness of the ICB–Pd layer. At an ICB–Pd layer thickness of 1-nm, the electrical resistivity of the overlying Cu interconnect was
. Moreover, the deposited film has adhesion strength as high as that of sputtered Cu on TaN, even for the case of the 1-nm-thick Pd catalyst layer. A uniform and continuous 10-nm-thick Cu seed layer was formed by electroless plating over a 1-nm-thick Pd layer, and subsequent Cu electroplating filled all high-aspect-ratio via holes without the appearance of voids.
C688
Kazuo Kondo, Keiji Watanabe, Yuji Abe, Junko Haji and Masaru Shimizu
C692
C. Montero-Ocampo, D. Villegas and L. Veleva
C697
Lucia D’Urzo, HaiHong Wang, Claudia Tang, Anthony Pa and Charlie Zhi
A technique has been developed for the study of the reaction mechanism and the monitoring of copper electroplating baths utilizing a combination of solid phase extraction and high-performance liquid chromatography. This method appears suitable for live electroplating bath control as well as for organic identification, concentration measurement, and reaction mechanism studies. The results from the experiments carried out with the technique described in this paper show how the monitoring of a few diagnostic peaks recovered from a live bath sample can be directly used for this purpose. Two copper sulfuric plating baths at different acidity were used for this study. The stability, degradation mechanism, and by-products of bis(sodiumsulfopropyl) disulfide were addressed in Part I, while polyethylene glycol (PEG) behaviors are studied in Part II. The identification of PEG breakdown by-products was achieved in this work.
C701
Yosuke L. Kawamura, Tetsuo Sakka and Yukio H. Ogata
A new method to control the size and distribution of electrodeposited metal on a semiconductor was investigated, using a system of Pt deposition on p-type Si. Pt is a noble metal, and electrodeposition is possible on p-type Si through hole injection to the valence band. When the Si surface is illuminated, an additional charge-transfer path becomes possible utilizing electrons photoexcited to the conduction band. The two pathways give different morphologies for the deposits. Fine and dispersed particles were electrodeposited under illumination, indicating the nucleation process was prevailing; in the dark, grown deposits were observed and the dominant process was crystal growth. We used the different deposition behavior to control the size and distribution of electrodeposits by the illumination-modulated method. Initial illumination gives nuclei of electrodeposits, and the adjustment of the duration can control the number of electrodeposits. The following electrolysis in the dark grows the deposits and can control the size. The method showed the possibility of controlling the size and distribution of Pt electrodeposits on p-type Si without changing applied potential.
C706
Jaesung Lee and Jan B. Talbot
The primary and secondary current distributions for the particle incorporation process during electrocodeposition of a metal film were numerically studied. The growth of an electrodeposited film along the electrode is governed by the local current density that is affected by the presence of a nonconducting particle. It was assumed that the effect of lateral displacement of the fluid between a particle and an electrode is negligible. The level set method was used to track the moving interface as it grows around the particle, and the Laplace equation for the electrical potential was solved by a finite-element method. For a primary current distribution, voids beneath the particle are generated due to the characteristics of the potential distribution, so that the metallic film does not grow along the particle surface. The resistance increment due to the presence of the particle was compared for the cases of stationary and growing metallic films. A small void on top of the particle when incorporated by metal is observed with a secondary current distribution.
C716
Jun Zhang, W. X. Zhou, Mary B. Chan-Park and Samuel R. Conner
Electrochemical Synthesis and Engineering
D161
Atsushi Murotani, Mahito Atobe and Toshio Fuchigami
D167
Michael M. Crouse, Albert E. Miller, David T. Crouse and Ataul Aziz Ikram
A nanoporous alumina template made from a multilayer metal film structure has been developed that allows for the in situ removal of the electrically insulating alumina barrier layer, exposing a Pt electrode at the pore bases. This barrier-free nanoporous system is of great use for dc electrodeposition of a wide variety of materials in the alumina pores. This work in particular describes the development of a multilayer thin film precursor consisting of a Si substrate with thin Pt and Ti and a thicker Al layer in that order. After the Al is anodized, producing the porous alumina, the resulting
is selectively removed at the base of the alumina pores exposing the Pt electrode. The metals in the precursor perform different roles in the fabrication and allow the alumina template to be fabricated directly on the final substrate with no film transfer technique involved. This allows Si to be used as the substrate, which could then include electronic circuitry. Several techniques are used to analyze the resulting template.
D173
D. Mangaiyarkarasi, E. J. Teo, M. B.H. Breese, A. A. Bettiol and D. J. Blackwood
Photoluminescence images containing several distinct color emissions, from green to red, have been obtained using high-energy focused ion beam irradiation, in conjunction with metal-aided anodization of
p-type silicon. The ion irradiation increases the local resistivity in a controlled manner resulting in smaller hole currents flow through the irradiated areas. This causes a controlled redshift of up to
in the photoluminescence emission, which in terms of the quantum confinement model would correlate to larger nanocrystallites forming in the irradiated region.
D177
Kazuo Onda, Takahiro Ohba, Hironobu Kusunoki, Shinya Takezawa, Daisuke Sunakawa and Takuto Araki
Recently, ozone is used for many purposes as an environmentally friendly oxidant. An ozone production device with high ozone concentration and low production energy is therefore desired. One candidate for such a device is ozone water production in a water electrolysis cell using a solid polymer electrolyte with
anode catalyst. Such a device would have the advantages of being compact and producing high-concentration ozone water directly through deionized water electrolysis. We have studied ozone water production with different electrode and electrolyte compositions and operation conditions, with the aim of improving ozone production performance. The two electrolytes tested were Nafion 117 and a membrane electrode assembly (MEA) with Pt catalyst on the cathode side of Nafion 117. The two electrodes tested were a single layer of Ti expanded metal and four layers of Ti-expanded metal with different meshes. Ozone water production tests were performed for many hours with changes in temperature, water flow rate, current density, current interruption time, and other factors to optimize experimental conditions. The voltage–current characteristics of water electrolysis cell were improved significantly when the electrode was four layers of Ti-expanded metal and the electrolyte was MEA with Pt catalyst on the cathode. Stable ozone water concentration was obtained after the cell had been operated for about 8 h. The optimum temperature, water flow rate, and current density for ozone water production are 25–30°C,
, and
, respectively. Further, the noninterrupted supply of small current suppressed the performance deterioration of ozone water production by current interruption, and the ozone production energy was reduced by supply of oxygen to the cathode.
D184
K. Dring, R. Dashwood and D. Inman
Diagrams showing equilibrium potentials (relative to the standard chlorine electrode) plotted vs the negative logarithms of oxide-ion activity
have been constructed for titanium species including oxides, chlorides, and metal, in molten calcium chloride over the temperature range 800–1100°C. The utility of such diagrams is particularly evident in the field of the molten salt extractive metallurgy of titanium via recently developed electrochemical processing methods. These plots suggest ideal process routes that produce low-oxygen titanium under controlled melt composition and potential.
Physical and Analytical Electrochemistry
E299
Daniel Andreescu and Omowunmi A. Sadik
E308
Xiao Y. Yan and Derek J. Fray
E319
Francisco Alcaide, Enric Brillas and Pere-Lluís Cabot
The oxidation of
to water on commercial platinum catalyzed carbon-polytetrafluoroethylene gas diffusion electrode (GDE) has been studied in deoxygenated aqueous solutions with KOH concentrations in the range
. The
couple behaves reversibly in open circuit, closely following the Nernst equation. A semiempirical equation in agreement with a Tafel–Volmer mechanism, accounting for diffusion, adsorption, inhibition, charge transfer, and ohmic-type drop in the wetted electrode pores, has been developed to quantitatively explain the steady-state linear sweep voltammograms for the different media, temperatures, and feeding hydrogen partial pressures tested. Charge transfer is also slow at high overpotentials except for
KOH. The micropolarization in the current–potential region around the reversible potential has been interpreted considering the Tafel reaction as the rate-determining step. The decay in exchange current density and the increase in activation energy both, at the reversible potential and high overpotentials, with raising KOH concentration has been ascribed to the increasing blocking and energetic effect of adsorbed hydroxyl species. The results of the activation energies suggest that the reactive Pt(110) faces are dominant in the dispersed Pt particles of the GDE.
E328
Guohong Qiu, Meng Ma, Dihua Wang, Xianbo Jin, Xiaohong Hu and George Z. Chen
E337
Parichatr Vanalabhpatana and Dennis G. Peters
In dimethylformamide containing tetramethylammonium tetrafluoroborate and deliberately added water, stoichiometric quantities of 1-bromooctane and electrogenerated cobalt(I) salen react to give octylcobalt(III) salen. When a solution of octylcobalt(III) salen is irradiated with ultraviolet-visible light, the cobalt-carbon bond is broken to form an octyl radical and cobalt(II) salen within a solvent cage. Introduction of dioxygen causes an insertion reaction that leads to an octylperoxocobalt(III) salen intermediate, which subsequently decomposes to produce 1-octanal in up to 47% yield. Under similar experimental conditions, a two-to-one molar ratio of electrogenerated cobalt(I) salen and
-dibromo-
-xylene gives rise to μ-(1,3-xylenyl)-bis[(salen)cobalt(III)] which can photodecompose, followed by insertion of dioxygen, to afford μ-(1,3-xylenyl)-bis[dioxo(salen)cobalt(III)]. Then the latter intermediate undergoes decomposition to form
-phthaldialdehyde in up to 61% yield. In contrast, the ortho and para isomers of
-dibromoxylene react with electrogenerated cobalt(I) salen, eventually to give a dialdehyde in small quantities (3–10%).
Dielectric Science and Materials
F153
Jaehyun Kim and Kijung Yong
F156
V. Jousseaume, M. Fayolle, C. Guedj, P. H. Haumesser, C. Huguet, F. Pierre, R. Pantel, H. Feldis and G. Passemard
F162
Dhananjay Bhusari, Harley Hayden, Ravindra Tanikella, Sue Ann Bidstrup Allen and Paul A. Kohl
F171
Dong-Hau Kuo and Wen-Cheng Tseng
Semiconductor Devices, Materials, and Processing
G731
K. Sueoka
A practical simulator for internal gettering (IG) of nickel and copper by oxide precipitates was developed in which the diffusion and reaction processes were included. In this simulator, the morphology of oxide precipitates was considered. It was found that the diffusion-limited model, which well explained Fe gettering, could not explain the reported experimental results of Ni and Cu gettering. IG of Ni and Cu contamination was analyzed to be reaction-limited. The simulator also showed that (i) a higher density of precipitates provides more efficient gettering sites than a low density of larger precipitates at a fixed amount of precipitated oxygen, and (ii) the precipitate morphology of platelet is more effective for IG than that of sphere at a fixed precipitate volume. Further, the oxide precipitates with high density of about
should be prepared just below the device active region in rapid thermal anneal process. The present IG model was combined with the reported oxygen precipitation model. These models make possible to control the oxygen precipitation for optimized IG.
G736
Tsutomu Shinagawa, Masanobu Izaki, Haruyuki Inui, Kuniaki Murase and Yasuhiro Awakura
G742
Mohamed M. Hilali, Mowafak M. Al-Jassim, Bobby To, Helio Moutinho, Ajeet Rohatgi and Sally Asher
G754
S. C. Tan, L. Liu, Y. P. Zeng, A. See and Z. X. Shen
G757
Satyanarayana Myneni and Dennis W. Hess
G766
Kuo-Lung Fang and Bing-Yue Tsui
G772
A. Zimmer, N. Stein, L. Johann, S. Van Gils, H. Terryn, E. Stijns and C. Boulanger
G778
Yu-Shyan Lin and Yu-Lung Hsieh
G781
Milind S. Kulkarni and Vladimir V. Voronkov
A computationally efficient model to quantify the microdefect distributions in Czochralski grown silicon crystals is proposed and numerically solved. All microdefects are approximated as spherical clusters. The novelty of the proposed model centers on a simplified treatment of the population of the clusters at any location; the average radius of the clusters in the population is approximated by the square root of the average of the squared radii of all clusters. The formation of the clusters is described by the classical nucleation theory. The growth of the clusters at any location is quantified by an auxiliary variable proportional to the total surface area of the clusters present at the location. A comparison between the predictions of the novel model with both a traditional model treating the size distribution of the clusters in the actual cluster population and the experimental observations validate the novel model.
G787
W. Lerch, S. Paul, J. Niess, F. Cristiano, Y. Lamrani, P. Calvo, N. Cherkashin, D. F. Downey and E. A. Arevalo
G794
Youngjo Tak, Kijung Yong and Chinho Park
A high density of aligned ZnO nanorods was grown on Pt buffer layer coated Si substrates. Ultrathin Pt buffer layers were deposited on Si(111). The ZnO nanorods were synthesized by metallorganic chemical vapor deposition using diethylzinc and oxygen. The optimum growth temperature was
to obtain aligned ZnO nanorods. The grown ZnO nanorods had single-crystalline atomic structure and pure compositions without any impurities. The nanorods showed a strong near-band-edge PL emission at
with no significant deep-level emission peaks. The morphology of ZnO nanorods grown on Pt buffer layer was compared with other buffer layers such as atomic layer deposited ZnO and Zr metal buffer film.
Semiconductor Devices, Materials, and Processing
G750
Satoshi Kamiyama, Takayoshi Miura, Yasuo Nara and Tsunetoshi Arikado
Sensors and Displays: Principles, Materials, and Processing
H157
Artur Benisek and Werner Sitte
H161
Kee-Sun Sohn, Duk Hyun Park and Ji Sik Kim
The ultimate goal of the present investigation was to develop an
,Dy thin-film phosphor on the surface of mechanical test specimens to act as a stress or crack indicator during testing. As a preliminary step,
,Dy thin-film phosphors were deposited on several conventional substrates such as quartz glass, Si(111), Si(001), and corrugated quartz glass using a pulsed laser deposition (PLD) technique. Processing parameters were optimized, in an attempt to enhance the efficiency of luminescence of the
,Dy thin-film phosphor. The optimal PLD processing conditions for the
,Dy thin-film phosphor were different from that for other conventional oxide thin-film phosphors in that an oxygen supply during the PLD process was not necessary, a postdeposition annealing in an oxidizing atmosphere was ineffective, and the corrugated substrate did not have a significantly enhanced extraction efficiency. By adopting the best PLD processing conditions, based on the preliminary depositions on conventional substrates, the
,Dy thin-film phosphor was deposited on the surface of a compact tension specimen composed of polycrystalline
and the applicability of the
,Dy thin-film phosphor as a stress or crack indicator was verified in an actual mechanical test.
H168
V. Sivakumar and U. V. Varadaraju