2371
Mingming Geng, Jianwen Han, Feng Feng and Derek O. Northwood
2376
N. Sac Epée, B. Beaudoin, V. Pralong, T. Jamin, J‐M. Tarascon and A. Delahaye‐Vidal
To investigate the self‐discharge mechanism in
cells, the interactions of hydrogen with the β‐NiOOH and γ‐NiOOH nickel oxyhydroxide phases were simulated in a water‐loaded autoclave as functions of both temperature and pressure. Under such conditions, X‐ray diffraction measurements coupled with transmission electron microscopy showed that both γ(III) and β(III) phases are reduced to a β(II) phase, thus providing direct evidence of hydrogen‐nickel oxyhydroxide chemical interaction in charged
cells. The kinetics for such a reaction were found to be mainly controlled by temperature rather than hydrogen pressure. Partial dissolution of solid β‐NiOOH and γ‐NiOOH phases, followed by dissolved hydrogen reduction concomitant with an oriented nucleation growth of the reduced phase on the intact NiOOH, is proposed to account for the self‐discharge mechanism observed in the autoclave. © 1999 The Electrochemical Society. All rights reserved.
2382
V. Pralong, N. Sac Épée, S. Taunier, B. Beaudoin, T. Jamin, A. Delahaye‐Vidal and J‐M. Tarascon
2387
Marco Giorgetti, Stefano Passerini, William H. Smyrl, Sanjeev Mukerjee, X. Q. Yang and James McBreen
Vanadium pentoxide materials prepared through sol‐gel processes act as excellent intercalation hosts for lithium as well as for polyvalent cations. Previous ex situ X‐ray absorption spectroscopy and X‐ray diffraction characterizations have shown that the electrochemical performance of vanadium pentoxide xerogels depends inversely on the long‐range order of the
structure. Recently, new ways to prevent the self‐organization of the dry materials, which takes place upon water removal from the starting hydrogel, have been introduced. In the present paper we report on the in situ X‐ray absorption spectroscopy characterization of a spray‐coated
(freeze‐dried) xerogel cathode upon lithium intercalation. © 1999 The Electrochemical Society. All rights reserved.
2393
Daniel Häringer, Petr Novák, Otto Haas, Benoît Piro and Minh‐Chau Pham
2397
R. A. M. Hikmet, M. P. J. Peeters, J. Lub and W. Nijssen
Mixtures containing liquid electrolyte and α,o‐alkane diacrylates were produced. Upon polymerization two‐phase gels consisting of polymer‐rich and polymer‐poor phases were obtained. The structure and the properties of the gels were studied using nuclear magnetic resonance, complex impedance spectroscopy, and electron microscopy. Conductivity data of various mixtures before and after polymerization were fitted to a master curve using a modified free‐volume theory. Low interaction between the polymer and the lithium ions in these gels ensures that the transport number for lithium is independent of the polymer concentration in various systems. Lithium metal batteries were constructed in which the two‐phase gels performed a dual function as an ion conductor as well as a separator. The gel morphology was found to be very important in determining the performance of such batteries. By optimizing the morphology of the gels, internal short‐circuiting could be prevented, and lithium metal cycling efficiencies in excess of 95% could be obtained. © 1999 The Electrochemical Society. All rights reserved.
2404
Y. Shao‐Horn, S. A. Hackney, A. R. Armstrong, P. G. Bruce, R. Gitzendanner, C. S. Johnson and M. M. Thackeray
2413
The following article is Free article
Daniel R. Baker and Mark W. Verbrugge
For electric‐vehicle and hybrid‐vehicle applications, it is expedient to determine what factors are likely to limit battery performance and determine cell designs that optimize operation for a particular application. This paper provides a derivation of the governing equations and an analytic solution useful for thin‐film battery design. Specifically, differential equations consistent with a two‐dimensional representation of a thin‐film battery are developed based on the underlying physical chemistry. A perturbation approach is used to derive a simpler set of governing equations, and associated analytic solutions for cell energy, power, and thermal characteristics are constructed. The analytic solution of this work assumes a secondary current distribution and linear kinetics for the porous electrodes; the associated system of model equations is thus linear. These assumptions should be valid for short times after the start of charging or discharging from a quiescent state. © 1999 The Electrochemical Society. All rights reserved.
2425
P. Durán, F. Capel, C. Moure, A. R. González‐Elipe, A. Caballero and M. A. Bañares
By using X‐ray diffraction lattice parameter measurements and Raman spectroscopy studies, both the solid solubility limit of titania in yttria tetragonal zirconia polycrystalline solid solutions
and the
tetragonal solid solution field in the
system have been established. Valence state, site symmetry, and changes in local structures of Ti ions in Y‐TZP with 5 and 10 mol %
are studied for the first time using EXAFS (extended X‐ray absorption fine structure), XANES (X‐ray absorption near edge structure), and X‐ray photoelectron spectroscopy. The total electrical conductivity in air of the
tetragonal solid solution decreases with increasing titania content. XANES results show that as the
dissolves into the tetragonal zirconia Y‐TZP matrix, a displacement of
ions from the center of symmetry seem to take place which leads to a nonrandom substitution of
ions on
lattice sites. Ti‐O bond distances derived from EXAFS results indicate that
ion can be in a square‐pyramidal arrangement, i.e., fivefold oxygen‐coordinated. As a consequence, two kind of cation‐oxygen vacancy associations (
and
) with different diffusion dynamics are created. This results in a decrease of the global concentration of moving oxygen vacancies and therefore, a decrease of ionic conductivity. Electronic conductivity, n‐type, only appeared at oxygen partial pressure lower than
atm and above 800°C in Y‐TZP containing 10 mol % titania. Such an n‐type electronic conduction was attributed to a hopping of electrons between
and
cations by a small polaron hopping mechanism. © 1999 The Electrochemical Society. All rights reserved.
2435
Sophia E. Hayes, Hellmut Eckert, William R. Even Jr. and Ronald Guidotti
There has been a great deal of discussion on the potential role of heteroatoms in carbons intended for lithium ion intercalation. Previous observations have been mixed, ranging from beneficial to detrimental effects on intercalation capacity, irreversible losses, and charge efficiencies. The introduction or substitution of silicon into a carbon matrix prepared by chemical vapor deposition has demonstrated a positive effect. The present study concerns substitutional effects in disordered carbons synthesized from polymer precursors. Solid‐state nuclear magnetic resonance, photoacoustic IR spectroscopy, X‐ray fluorescence, and high‐resolution transmission electron microscopy were used to follow the modified carbon synthesis. Silicon is successfully incorporated into the polymer matrix by copolymerizing the precursors with tetravinylsilane. On oxidative stabilization and pyrolysis, however, the Si‐C connectivity is replaced by Si‐O coordination. These silicon species appear to be discrete, and no evidence for either a crystalline or amorphous secondary
phase is seen. These silicon species have a profound effect on the electrochemical performance. Irreversible loss processes are greatly increased, and charge efficiencies are decreased when compared to nonsubstituted controls. © 1999 The Electrochemical Society. All rights reserved.
2443
Atsushi Funabiki, Minoru Inaba, Takeshi Abe and Zempachi Ogumi
The kinetics of the stage transformation of lithium‐graphite intercalation compounds from dilute stage 1 to stage 4 were studied using potential‐step chronoamperometry and alternating current impedance spectroscopy. Highly oriented pyrolytic graphite was used as a host material. The current‐transient curve showed a current hump, suggesting that the stage transformation was initiated by the nucleation and growth of stage 4. The phase‐boundary movement was discussed quantitatively using a simple geometric model. The phase boundary progressed in proportion to time during the initial stage. The rate constant was inversely proportional to the product of the interfacial resistance and the geometric edge‐plane area, indicating that the phase‐boundary movement was determined by the rate of the reaction at the graphite/electrolyte interface. In the following stage, the phase boundary advanced in proportion to the square root of time. The parabolic rate constant obtained experimentally was in satisfactory agreement with that calculated using Wagner's classical model which describes the diffusion within two phases separated by a phase boundary. These results indicated that the phase‐boundary movement was initially determined by the rate of the interfacial electrochemical reaction and was controlled thereafter by a diffusion process. © 1999 The Electrochemical Society. All rights reserved.
2449
Li Qingfeng, Flemming Borup, Irina Petrushina and Niels J. Bjerrum
2455
N. J. Dudney, J. B. Bates, R. A. Zuhr, S. Young, J. D. Robertson, H. P. Jun and S. A. Hackney
2465
Chi‐Chang Hu and Yao‐Huang Huang
2472
R. Retoux, T. Brousse and D. M. Schleich
2477
Shin‐ichi Tanaka, Norimitsu Hirose and Toshiyuki Tanaki
Raney‐nickel (Ni) cathodes were prepared on nickel wire from aluminum powder and titanium hydride powder by heat‐treatment. The influence of the addition of titanium to the Raney‐Ni electrode on the polarization characteristics of the hydrogen evolution reaction was studied in 1 M NaOH at 303 K. Although the coated layer was composed of nickel with a small amount of aluminum and titanium, the titanium was enriched the most. The relative surface area of the Raney‐Ni cathodes was about 3500 independent of the presence of titanium, but titanium could decrease the hydrogen overpotential. © 1999 The Electrochemical Society. All rights reserved.
2481
Manabu Ihara, Chiaki Yokoyama, Abulet Abudula, Ryuzaburo Kato, Hiroshi Komiyama and Koichi Yamada
Power‐generation experiments of solid‐oxide fuel cells with Ni/yttria‐stabilized zirconia cermet anodes were carried out by changing the water‐to‐methane ratio in the fuel. To separate the electrochemical reactions occuring on the three‐phase boundary of the anode from the steam‐reforming reactions, premixed gases corresponding to the composition at thermal equilibrium were used as the fuel. The reactions on the anode were quantitatively clarified at different steam‐to‐methane ratios by making a mass balance of the elements and electrons and by determining the anode exit gas composition. For dry (i.e., no water) methane fuel, the carbon deposited on the three‐phase boundary from the methane mainly reacted with oxide ions
. With increasing steam‐carbon (S/C) ratio from S/C = 0.5 to 1, hydrogen became the dominant reactant. The anode potential vs. current density for S/C = 1 agreed with that for hydrogen diluted with argon. At S/C ratios higher than 1.5, CO in the inlet gas reacted with oxide ions. © 1999 The Electrochemical Society. All rights reserved.
2488
D. Vanmaekelbergh and B. H. Erné
A new model is proposed for the anodic dissolution of metals. It is assumed (i) that the rate‐determining process is the transfer of metal ions through the double layer, (ii) that ion‐transfer proceeds in two steps via an adsorbed, partially solvated ionic intermediate, and (iii) that the surface concentration of the intermediate species affects the potential distribution across the double layer, hence also the ionic transfer rate. It is shown that the model can explain the current‐potential characteristics and the electrical impedance of anodically dissolving metals. The low‐frequency loop of the electrical impedance is shown to arise from relaxation of the double layer during transfer of an ion. © 1999 The Electrochemical Society. All rights reserved.
2495
L. F. Garfias‐Mesias and W. H. Smyrl
Photoelectrochemical microscopy (PEM) was used to locate pitting precursor sites on polycrystalline titanium immersed in sulfuric acid and in ferrocyanide solutions. PEM imaging was done with both a conventional method and a new shear‐force feedback method. The resolution of the PEM images obtained are highly dependent upon the size and preparation procedure of the optical fiber used for the test. 1 μm diam etched tips yield higher lateral resolution images compared to commercially available “pulled” tips. PEM with simultaneous independent topography (using the tuning fork method) resolved submicron features at precursor sites at inclusions and grain boundaries. Both PEM and topographic images were obtained in situ with high lateral resolution by using specially fabricated tips with 100 nm aperture. © 1999 The Electrochemical Society. All rights reserved.
2502
H. Habazaki, K. Takahiro, S. Yamaguchi, K. Shimizu, P. Skeldon, G. E. Thompson and G. C. Wood
The role of iron during anodizing of a non‐equilibrium Al‐4 atom % Fe alloy at high faradaic efficiency has been examined using high resolution transmission electron microscopy, Rutherford backscattering spectroscopy, and X‐ray photoelectron spectroscopy. Anodic oxidation proceeds with initial formation of an anodic alumina film, free from iron species, and subsequent formation of an iron‐contaminated alumina film, which is eventually contaminated by iron species throughout its thickness. During the initial oxidation of aluminum, iron atoms are accumulated in a thin layer of alloy, about 2–3 nm thick, immediately beneath the anodic film. When the average composition of the enriched alloy layer reaches approximately Al‐25 atom % Fe, both aluminum and iron are oxidized and are incorporated into the film in their approximate alloy proportions in the presence of the enriched alloy layer. The incorporated iron species are in the trivalent state, and migrate outward in the growing anodic film about 1.8 times faster than
ions. The iron species eventually reach the film/electrolyte interface, forming a thin, iron‐rich, hydrated layer, probably composed of γ‐FeOOH. © 1999 The Electrochemical Society. All rights reserved.
2508
M. Keijzer, G. Lindbergh, K. Hemmes, P. J. J. M. van der Put, J. Schoonman and J. H. W. de Wit
The corrosion behavior of 304 stainless steel was characterized with cyclic voltammetry in a eutectic Li/K and Li/Na carbonate melt under anode and cathode gas of the molten‐carbonate fuel cell (MCFC). The corrosion rate of 304 steel was determined in four different environments of the MCFC with electrochemical methods and from cross‐sectional analysis of corrosion layers. These four environments were open‐circuit and MCFC‐load conditions both under anode and cathode gas. At open‐circuit conditions corrosion was more severe under the oxidizing cathode gas than under the reducing anode gas. On the contrary, at load conditions corrosion was more severe under anode than under cathode gas. The anodic polarization under anode gas enhances corrosion, whereas the high anodic polarization under cathode gas leads to anodic protection. Corrosion currents were measured with chronoamperometry and determined with Tafel extrapolation from quasi‐stationary polarization‐curve measurements. The difference between the corrosion layer thickness estimated from these corrosion currents and the corrosion layer thickness determined from cross‐sectional analysis is mainly due to contributing currents of either the MCFC‐anode gas reaction under anode gas or the MCFC‐cathode gas reaction under cathode gas. © 1999 The Electrochemical Society. All rights reserved. ©2001 American Geophysical Union
2517
Philippe Lam, Kartik Kumar, Gary E. Wnek and Todd M. Przybycien
This paper describes an electroless gold plating process for particulate 316L stainless steel. The process is based on a mildly acidic gold sodium thiosulfate/ascorbic acid plating solution and is performed under an inert environment at room temperature. The process affords a gold deposition efficiency of ∼50% as inferred from a modified tin chloride based spectrophotometric assay for gold ion concentration. Successful gold deposition depended on the removal of the thin, passivating surface oxide layer on the stainless steel; this was accomplished by an initial cleaning step with 2 M HCl. In situ cyclic voltammetry experiments on a stainless steel electrode and atomic force microscopy scans on small coupons were used to further characterize the oxide removal and gold deposition reactions. © 1999 The Electrochemical Society. All rights reserved. ©2001 American Geophysical Union
2522
Heini Saloniemi, Mikko Ritala, Markku Leskelä and Reijo Lappalainen
Deposition of lead sulfide thin films has been carried out from an aqueous solution using a novel electrochemical method which includes alternate anodic and cathodic reactions.
and
complexed with ethylenediaminetetraacetic acid were used as precursors. During the deposition the substrate potential was continuously cycled between two potentials. At the cathodic potential elemental Pb was deposited and at the anodic potential it was reoxidized and reacted with sulfide forming a PbS film. From basic solutions at pH 8.5, PbS films were deposited only with the cyclic method, but with acidic solutions at pH 5 also the conventional constant potential method could be used. The films were characterized by X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectrometry, wavelength‐dispersive X‐ray spectrometry, Rutherford backscattering spectrometry, elastic recoil detection analysis, deuteron induced reactions, and profilometry. The electrodeposited PbS films were stoichiometric and crystalline, having nontextured rock salt cubic structure. © 1999 The Electrochemical Society. All rights reserved.
2526
C. Madore, O. Piotrowski and D. Landolt
Through‐mask electrochemical micromachining has been employed to fabricate well‐defined three‐dimensional topographies in titanium. Well‐controlled shapes with a smooth surface finish were obtained using optimized electrolyte composition and electrochemical parameters. The shape change resulting from electrochemical etching through patterned photoresists were numerically simulated using the boundary element method, assuming the rate of titanium dissolution to be diffusion controlled. A satisfactory agreement was found between experimentally measured and simulated etched profiles. © 1999 The Electrochemical Society. All rights reserved.
2533
Kow‐Ming Chang, I‐Chung Deng, Ta‐Hsun Yeh and Chien‐Wen Shih
2540
James J. Kelly, Chunyan Tian and Alan C. West
The roles of two model additives, bis(3‐sulfopropyl) disulfide (SPS) and Janus Green B (JGB), in the deposition of copper from an acid‐copper sulfate electrolyte containing polyethylene glycol (PEG) and
were studied by deposition on microprofiled electrodes, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). It was found that leveling occurs only when all four additives are present, suggesting that additive‐additive interactions are important to the leveling mechanism. Moreover, an optimal flux of the active leveling agent exists, an effect that may be explained by the classical diffusion‐adsorption theory of leveling. SEM and TEM micrographs show that the additive SPS removes the columnar structure of the deposit and effects micron‐sized, unoriented grains provided PEG and
are present; the subsequent addition of JGB decreases the grain size of the film significantly. © 1999 The Electrochemical Society. All rights reserved.
2546
R. Lozada‐Morales, M. Rubín‐Falfán, O. Portillo‐Moreno, J. Pérez‐Álvarez, R. Hoyos‐Cabrera, C. Avelino‐Flores, O. Zelaya‐Angel, O. Guzmán‐Mandujano, P. del Angel, J. L. Martínez‐Montes et al
CdSe polycrystalline thin films were grown onto glass substrates by chemical bath deposition at 65°C. Structural, optical, and electrical properties of samples were characterized. The layers grew in the cubic phase as evidenced by X‐ray diffractograms. Using the first derivative of the optical absorption vs. phonon energy curves, two transitions were found, the fundamental at 1.8 eV and a second one at 2.2 eV, respectively. It is worthwhile to mention that the second transition has been reported only for the hexagonal CdSe modification. From the dark conductivity vs. 1/KT behavior on the 100–500 K range, it could be determined an activation energy of 0.3 eV at higher temperatures (>350 K) and a behavior following the variable range hopping model of Mott was satisfied at lower temperature. Electron dispersion spectroscopy measurements indicated stoichiometric CdSe material within the 1 % error bar. © 1999 The Electrochemical Society. All rights reserved.
2549
Xiangqun Zeng and Stanley Bruckenstein
2555
Xiangqun Zeng and Stanley Bruckenstein
We describe an approach that leads to a mechanism describing the lead ion adsorption and lead underpotential deposition (UPD) on a polycrystalline gold electrode in supporting electrolytes containing chloride, nitrate and/or perchlorate. By combining the electrochemical quartz crystal microbalance (EQCM) method with data from X‐ray photoelectron spectroscopy and time of flight secondary ion mass spectrometry, the existence of adsorbed anionic ligands was demonstrated. The lead UPD process goes through the reduction of both an adsorbed lead complex and a lead species present in the supporting electrolyte. © 1999 The Electrochemical Society. All rights reserved.
2562
T. Okada, K. Katou, T. Hirose, M. Yuasa and I. Sekine
Electropolymerized cobalt salen compounds on pyrolytic graphite electrodes were first tested as oxygen reduction catalysts in aqueous solutions of various pH. N,N′‐Bis(salicylidene)ethylenediaminocobalt(II) [abbreviated Co(salen)] and its analogs were polymerized on a basal plane of pyrolytic graphite electrode by electrochemical polarization from deaerated acetonitrile solutions. The cyclic voltammetry of Co(salen) modified electrodes showed that electropolymerized Co(salen) effectively catalyzed oxygen reduction in aqueous solutions, and features such as half‐wave potentials or limiting current density of oxygen reduction were satisfactory as compared with those of cobalt porphyrin‐modified electrodes. The characteristics of oxygen reduction catalyzed by electropolymerized Co(salen) were investigated using rotating ring‐disk electrode measurements in acidic, neutral, and basic solutions. The efficiency of four‐electron reduction of oxygen was found to be best in basic solutions. The results revealed that although in acidic media the catalyst performance deteriorated in a short time, the performance in neutral and basic media was relatively good as compared with that of platinum, the best catalyst for this reaction. © 1999 The Electrochemical Society. All rights reserved.
2569
M. Fedurco, P. Kedzierzawski and J. Augustynski
2573
S. P. Fusselman, J. J. Roy, D. L. Grimmett, L. F. Grantham, C. L. Krueger, C. R. Nabelek, T. S. Storvick, Tadashi Inoue, Takatoshi Hijikata, Kensuke Kinoshita et al
The design of a molten metal‐molten salt based chemical and electrochemical process for separation of actinides from plutonium‐uranium extraction waste requires a consistent set of thermodynamic properties for the actinides and rare earths present in nuclear waste. Standard potential data for Y, La, Ce, Pr, and Gd in molten LiCl‐KCl were obtained. Americium data obtained were standard potentials in molten LiCl‐KCl and activity coefficients for Cd and Bi. Data were obtained between 400 and 500°C. Results for the rare earth chlorides using an improved experimental technique were consistent with theory, with standard free energy of formation values somewhat more negative than those found in the literature. Special attention was given to Am in the LiCl‐KCl/Cd system because it can exist as the +2 and/or +3 ion in this system. Americium ions existed only as the +3 ion in LiCl‐KCl/Bi. Standard electrochemical potentials for
in LiCl‐KCl eutectic at 400, 450, and 500°C were −2.893, −2.853, and −2.838 V, respectively, relative to
. Standard electrochemical potentials vs.
for
in LiCl‐KCl eutectic were −2.83 V at 450°C and −2.78 V at 500°C. Activity coefficients for Am in molten Cd were
and
at 450 and 500°C. Activity coefficients for Am in molten Bi were
and
at 450 and 500°C. © 1999 The Electrochemical Society. All rights reserved.
2581
Norio Miura, Hirotaka Murae, Hajime Kusaba, Jun Tamaki, Go Sakai and Noboru Yamazoe
Oxygen permeation properties of
(A′=Ca, Sr, Ba, and Mg) were investigated. The oxides with
≤ 0.2 had hexagonal
structure at room temperature. The disk membranes (1.0 mm thick) made of these oxides, when cooled from high temperature, showed significant rates of oxygen permeation down to critical temperatures characteristic of the kind of oxides, below which the rates sharply diminished. Among the oxides tested,
showed the largest rate (
at standard temperature and pressure
) at 900°C. As indicated by the X‐ray diffraction and thermogravimetry‐differential thermal analysis, this oxide underwent phase transformation between the above structure (low‐temperature phase) and a cubic perovskite structure (high‐temperature phase), which were oxygen nonpermeable and oxygen permeable, respectively. On heating, the oxygen content (2.5 +δ) of the oxide decreased in two steps, i.e., first from 2.75 to 2.6 over the temperature range 400 to 600°C without changing the structure, and then from 2.6 to 2.5 at the temperature of transformation to the high‐temperature phase (about 900°C). The rate of oxygen permeation of the oxide at 900°C was found to depend on the membrane thickness. Based on these results, oxygen permeation and its relevance to phase transformation are discussed. © 1999 The Electrochemical Society. All rights reserved.
2587
N. Yamada, T. Yaguchi, H. Otsuka and M. Sudoh
A practical‐scale cell
with a trickle‐bed electrode was developed for on‐site electrochemical production of hydrogen peroxide by the cathodic reduction of oxygen. Terminal voltage and current efficiency were affected by the dispersions of liquid and oxygen gas in the trickle‐bed cathode and by the current density. Current efficiency was improved by obtaining uniform dispersions of electrolyte and oxygen in the trickle‐bed cathode. A current efficiency of 97.4% was obtained at a cell voltage of 2.1 V and a current density of
. To save power, the temperature of the electrolyte was not controlled, and exothermic reactions increased the temperature of the anolyte recovered at the outlet from the inlet temperature of 37–44°C. The temperature of the catholyte rose simultaneously from an inlet temperature of 25–44°C. The crystallization of sodium peroxide within the cathodes was prevented by controlling peroxide concentration, and the maximum concentration of hydrogen peroxide in a 5.0% caustic soda solution was 2.1%. © 1999 The Electrochemical Society. All rights reserved.
2592
M. I. Florit, D. Posadas, F. V. Molina and E. M. Andrade
The impedance response of poly(o‐toluidine) (POT) electrochemically grown films was investigated in sulfuric acid 3.7 M, in the temperature range 218 to 293 K. The Nyquist diagrams as a function of temperature show that the transition potential from the nonconductive to the conductive state shifts in the positive potential direction as the temperature decreases. This implies that, at low temperatures, a greater field is needed to induce the transition. In the nonconductive state both the high‐frequency and the low‐frequency resistances increase as the temperature is decreased. The Arrhenius plots for both show a break at about 255 K. This is in agreement with the fact that the high‐frequency resistance is controlled by ionic movements and that there is charge‐transfer control at the polymer/solution interface. In the conductive state the low‐frequency capacitance is independent of temperature, showing that the active site concentration does not depend on the temperature. The low‐frequency resistance in this potential region also depends on the temperature. No break is observed in the Arrhenius plot for this quantity. However from its slope it is inferred that ionic motions within the polymer control the charge transport in this state. © 1999 The Electrochemical Society. All rights reserved.
2598
Sarah R. Jacob and Richard G. Compton
Zinc dialkyldithiophosphates (ZDTPs) are widely incorporated in lubricant formulations as antioxidant and antiwear additives. Using the model compound zinc n dibutyldithiophosphate (Bu-ZDTP) in dimethylformamide (DMF) solution, cyclic voltammetry is applied to a detailed study of Bu-ZDTP electro‐oxidation. Bu-ZDTP is shown to be oxidized in a chemically irreversible electron transfer process under diffusionf‐limited conditions. A similar study of Bu-ZDTP reduction revealed nucleation of zinc at the electrode surface. A chronoamperometric investigation of zinc deposition classified the nucleation according to a progressive mechanism with the diffusion coefficient for Bu‐ZDTP in (DMF) solution as
. By comparison with diffusion coefficients obtained via Levich analysis of Bu-ZDTP oxidation, the oxidation process is assigned as a two‐electron transfer. The use of atomic force microscopy as a means of directly visualizing zinc nuclei formed as a result of Bu-ZDTP reduction is described. © 1999 The Electrochemical Society. All rights reserved.
2606
Stefan Diethelm, Alexandre Closset, Kemal Nisançioglu, Jan Van herle, A. J. McEvoy and Turgut M. Gün
Oxygen diffusion is treated in a dense electronically conducting cobaltate pellet blocked ionically on one surface, electronically on the other, and sealed on its cylindrical periphery. A procedure is developed for extracting the chemical diffusion and surface exchange coefficients for oxygen by use of the asymptotic equations derived for the current response to a potential step at short and long times. It is shown that, while the formation of interfacial phases by reaction between the sample and the electrolyte may affect the surface exchange coefficient, the chemical diffusion coefficient data determined by the present approach are independent of such interfacial phenomena. The consistency of data obtained from several specimens with varying thickness and manner of interfacing with the electrolyte validates the diffusion model and the method used for data analysis. An oxygen permeation cell is also developed in this work as a modification of the diffusion cell. The new cell allows monitoring of the permeation rate by electrochemical means. The steady‐state permeation data obtained by the permeation cell are consistent with the chemical‐diffusion and surface‐exchange coefficients measured by the blocked diffusion cell as long as the assumptions of the related theoretical models are satisfied. This is a further validation of the diffusion model and the related methodology developed here for obtaining the necessary data for characterizing oxygen exchange and transport in such materials. © 1999 The Electrochemical Society. All rights reserved. ©2001 American Geophysical Union
2613
Strømme Mattsson, J. Isidorsson and T Lindström
We propose that the intercalation of ions from a liquid electrolyte into a solid material can be analyzed in terms of a model [J. Appl. Phys., 55, 3341 (1984)] developed for the release of alkali ions from interface traps in a metal‐oxide silicon structure. It is shown that the insertion of Li ions into Sn oxide is described very well by this model, and the diffusion coefficient of Li in the oxide as well as the release frequency of Li ions from surface traps could be obtained. The presence of current peaks in chronoamperometry curves could also be explained. © 1999 The Electrochemical Society. All rights reserved.
2616
Lin‐Feng Li, Dana A. Totir, Yosef Gofer, Kuilong Wang, Gary S. Chottiner and Daniel A. Scherson
The electrochemical properties of clean and oxygen‐contaminated polycrystalline Ag surfaces have been examined in
oxide solutions in ultrahigh vacuum (UHV) environments at temperatures in the range 323–333 K. Unlike the behavior observed for Au and Ni under the same experimental conditions, no clearly defined volmmetric peaks were found during the first and subsequent cycles in the range 2.20–0.25 V vs.
initiated at the open‐circuit potential, 1.75 V vs.
. Instead, the scans in the negative direction were characterized by two adjoining regions in which the current increased linearly with potential, albeit at different rates, and the subsequent scans in the positive direction yielded comparatively much smaller currents largely independent of the applied potential. Integration of the voltammetric curves over the potential range 0.25 <
< 2.20 V vs.
revealed a pronounced imbalance between the charges obtained in the scans in the negative
and positive
directions. This phenomenon was attributed, by and large, to the high rates of Li dissolution into Ag at these temperatures, consistent with the presence of a low‐temperature eutectic in the Li‐Ag phase diagram. Additional support for this view was obtained from UHV non‐electrochemical measurements involving vapor‐deposited Li onto Ag, for which the amount of Li on the surface, as monitored by Auger electron spectroscopy, decreased markedly upon increasing the temperature from ca. 300 to 350 K. The voltammetry of oxygen‐contaminated Ag surfaces was characterized by a well‐defined peak in the scan in the positive direction centered at ca. 1.3 V, which persisted upon continuous cycling. Although the process responsible for this feature has not yet been identified, it provides a marker for detecting oxygen impurities on Ag in this electrolyte. © 1999 The Electrochemical Society. All rights reserved.
2620
Ricardo Jiménez and Miguel Gregorkiewitz
Sodium‐rich nepheline,
(□ = vacancy), has been synthesized from fused salts. Electron microprobe analyses and X‐ray diffraction Rietveld refinement were used to ascertain the composition and the K:Na = 1:1 occupation, leaving 5% vacancies in the large channel‖c. Guinier‐Lenné powder X‐ray diffraction from 100 to 895°C showed no phase transitions and yielded expansivities of
and
. Using polycrystalline pellets, impedance spectra
were registered at constant temperatures from 100 to 370°C. The dispersion of the permittivity, electric modulus, and impedance functions revealed three features with distinct Arrhenius behavior. Considering (i) anisotropic bulk diffusion within the grains, (ii) aggregation of these grains at random orientation in air, and (iii) intergrain and pellet‐electrode contacts, models were developed to simulate the spectra. Agreement with the observed data is obtained for the following assignments: a high‐frequency feature
corresponds to
movement along the large channel, which is fast but occluded between
ions; a low‐frequency electric modulus feature
corresponds to the movement of the blocking ion
along the large channel; and a low‐frequency impedance feature
corresponds to
movement within the ab plane. Due to the presence of
, the near dc conductivity ‖c is only (ca. 10 times (at 231°C) higher than ‖ab, in contrast with the high anisotropy
known for pure sodium nepheline. The accessible volume and its distribution within the framework were calculated for
and
and shown to aid in understanding of the diffusion mechanism. © 1999 The Electrochemical Society. All rights reserved.
2631
Alyssa C. Henry, Robin L. McCarley, Sudipta S. Das and Chantal G. Khan Malek
We describe the characterization of various commercial brands of poly(methyl methacrylate) (PMMA) sheets used in the LIGA process. LIGA, a German acronym for lithography, electroplating, and molding, is a relatively new method for construction of extreme high‐aspect‐ratio microstructures. Metal structures with millimeter‐by‐micron dimensions can be fabricated by electrode‐position of metals into developed features of the commonly used X‐ray‐sensitive resist, PMMA. Previous experiments from these laboratories have indicated that the adhesive strength of a given PMMA sheet to an electroplating substrate is a function of the source of the PMMA, thermal treatment of the PMMA, and the face of the PMMA sheet. We have used scanning force microscopy to inspect the topography of the faces of PMMA routinely used in the LIGA process. Depending on the thickness of the PMMA, or what face of a given PMMA sheet is inspected, the surface topography is found to vary from almost completely smooth to that where pits populate the surface. The dimensions and number of the pits depend on the thermal treatment of the PMMA sheets (annealing at an elevated temperature). Gas chromatography‐mass spectrometry indicates that residual methyl methacrylate (MMA) monomer content in the PMMA decreases upon annealing. Sampling of the local atmosphere during annealing through use of solid phase microextraction confirms that residual MMA is released. The variation in pit number and size, the result of different amounts of expelled MMA, leads to the noted differences in adhesive strength of the various PMMA sheets to the substrate. © 1999 The Electrochemical Society. All rights reserved.
2637
Lars‐Åke Ragnarsson, Erik Aderstedt and Per Lundgren
2643
Jui‐Chang Chuang, Shuo‐Lun Tu and Mao‐Chieh Chen
2648
Sean W. King, Robert J. Nemanich and Robert F. Davis
2652
Kenneth K.S. Lau and Karen K. Gleason
Solid‐state nuclear magnetic resonance (NMR) spectroscopy is applied to the study of films from pulsed plasma enhanced chemical vapor deposition from two hydrofluorocarbon gases,
and
. Beyond confirming the relative
fractions obtained from X‐ray photoelectron spectroscopy, NMR offered greater structural insight into the plasma film network.
NMR identified various network sequences, three
, five
, and three
segments, based on differences in next nearest neighbor attachment.
NMR distinguished between
and
bond configurations, with further separation of unsaturated nonfluorinated carbons into two distinct types. One is attributed to aromatic or graphitic carbon structures while the other is due to unsaturated carbons in closer proximity to fluorines. NMR also allowed changes in structure to be probed upon film thermal decomposition. The film from
showed both precursor desorption and
detachment, while that from
showed only
loss. © 1999 The Electrochemical Society. All rights reserved.
2659
A. Belaïdi, M. Safi, F. Ozanam, J.‐N. Chazalviel and O. Gorochov
In contrast to previous belief, we show that oxide is present at the silicon/dilute‐fluoride electrolyte interface even near the onset of anodic current, which corresponds to the regime of porous‐silicon formation. This point is supported by the observation of a transient anodic current when the potential is maintained in this region until a steady‐state current is reached, then stepped to a value near that of the open‐circuit potential. In situ infrared investigations confirm the presence of a submonolayer oxide film. Upon polarizing the interface, the electrochemical current and the surface concentrations of oxide and hydrogen exhibit slow relaxations. These transient features are accounted for in a simple kinetic model, which assumes two parallel dissolution pathways and a slow, potential‐dependent relaxation of the electrochemically active surface area. In this framework, the transition to the electropolishing regime is found to correspond to unit coverage of the electrochemically active surface by the oxide. © 1999 The Electrochemical Society. All rights reserved.
2665
Fan Zhang, Ahmed A. Busnaina and Goodarz Ahmadi
A new model including the effects of polishing pressure and platen speed on particle penetration depth in chemical mechanical polishing (CMP) processes is derived based on the particle adhesion theory, the surface plastic deformation, and the pad‐wafer partial contact. The predicted particle penetration depth is in good agreement with the experimental surface roughness data. Particle removal models in the final polishing and mechanical brushing/cleaning processes are proposed, and the removal forces are evaluated. The lift force in the hydrodynamic boundary layer is too small to lift particles off the surface and particles most likely roll off the surfaces by the drag force plus the contact forces from the pad or brush asperities. The effects of pressure, rotation speed, pad hardness, and chemical addition in post‐CMP are also addressed. © 1999 The Electrochemical Society. All rights reserved.
2670
W. Lerch, M. Glück, N. A. Stolwijk, H. Walk, M. Schäffer, S. D. Marcus, D. F. Downey and J. W. Chow
For the formation of ultrashallow junctions, a controlled gaseous ambient during rapid thermal annealing is indispensible. To understand the diffusion/activation mechanism, the influencing and depending variables have to be clarified precisely. Ion implantations of 1 keV boron at a fluence of
are annealed isothermally for 10 s at 1000, 1050, and 1100°C in an AST2800ε rapid thermal processing system under controlled concentrations of oxygen in nitrogen ambient (0–1 ppm up to 1%). The concentration‐depth profiles, measured by secondary ion mass spectroscopy, are analyzed within the framework of the kick‐out model involving diffusion enhancement via supersaturation of silicon self‐interstitials and the Fermi‐level effect. The validity of this interpretation is supported by the simulated results which are in good agreement with experimental data. Two input parameters for the SSUPREM IV simulator yield finite values of silicon self‐interstitial supersaturation as a function of temperature and oxygen concentrations, values for the boron diffusion coefficient via neutral and positively charged silicon self‐interstitials, and data for transient enhanced diffusion. After rapid thermal annealing for 10 s at 1050°C, the junctions vary within 800–1400 Å depending on the annealing ambient. © 1999 The Electrochemical Society. All rights reserved.
2679
B. Q. Shi and C. W. Tu
A study on
laser‐assisted chemical beam epitaxy of InP with trimethylindium and tertiarybutylphophine is reported here. In situ monitoring of the laser‐assisted growth surface is carried out using reflection high‐energy electron diffraction. The growth rates over laser‐irradiated and nonirradiated areas are interpreted in terms of physical chemistry of the physisorbed and chemisorbed layers. Two postulations on the photolytic mechanism responsible for growth enhancement with laser are made, which describe the roles of physisorbed group V and group III species in the mechanism. © 1999 The Electrochemical Society. All rights reserved.
2683
M. Akatsuka, K. Sueoka, H. Katahama and N. Adachi
A simulation model to calculate a slip length during thermal processes was proposed on the basis of dislocation kinetics. The dislocation velocity was calculated from gravitational and thermal stresses. The slip length was calculated by integrating the dislocation velocity by the duration of thermal processes. It was found that the model could predict the slip length, the optimum ramping rate, and wafer spacing quantitatively with high accuracy for 300 mm wafers. © 1999 The Electrochemical Society. All rights reserved.
2689
P. Wrschka, J. Hernandez, Y. Hsu, T. S. Kuan, G. S. Oehrlein, H. J. Sun, D. A. Hansen, J. King and M. A. Fury
We describe chemical mechanical polishing (CMP) of blanket and patterned aluminum films employing a polyurethane pad and a slurry based on alumina particles as the abrasive and hydrogen peroxide as the oxidizer. The experiments were conducted at pressures from 19 to 47 kPa and at linear velocities from 26 to 48 m/min, and yielded Al removal rates from 80 to 250 nm/min. The oxidant concentration has a weak effect on the removal rate of Al. Polishing selectivities of Al to silicon dioxide as high as 130:1 were obtained with the maximum selectivities being observed at regions of low pressures and low velocities. The Preston equation fails to describe the dependence of the removal rate on pressure and velocity, and a power function is proposed instead. X‐ray photoelectron spectroscopy was used to examine the surface of Al before and immediately after CMP. These experiments provided information on the thickness of the oxidized Al layer. We found that larger removal rates correlated with a smaller Al‐oxide thickness. We conclude from this that Al CMP proceeds by oxidation of the Al and subsequent Al‐oxide removal. © 1999 The Electrochemical Society. All rights reserved.
2697
Yoshio Fukuda, Wei Zhou, Kazuo Furuya and Hiroshi Suzuki
As‐prepared low resistivity p‐type porous silicon (PS) and PS aged for 15 months are subjected to etching treatment in 0.05% aqueous NaOH at room temperature. Photoluminescence (PL) properties of the treated PS are correlated with chemical states and microstructures analyzed by Fourier transform infrared spectroscopy and scanning electron microscopy. The red PL from as‐prepared PS is almost quenched by NaOH treatment for 10 s, while a lightly oxidized outer surface layer of about 100 nm is removed. The red PL from aged PS becomes weak gradually as the Si‒O bond content in PS decreases with NaOH treatment time. The aged PS shows strong PL even after the treatment for 450 s, while the heavily oxidized outer surface layer partially remains. These results suggest that the oxidized outer surface layer in PS is responsible for the red PL. © 1999 The Electrochemical Society. All rights reserved.
2702
D. A. Stocker and E. F. Schubert
The roughness of GaN surfaces produced by photoenhanced etching is significantly reduced by the introduction of an external bias voltage during the etching process. The root‐mean‐square surface roughness decreases from a maximum of approximately 1700 nm to a minimum of 20 nm as the bias voltage is increased from 0 to 2.5 V, and as the KOH concentration is decreased from 1.0 to 0.01 M. Etch rates as high as 0.4 μm/min are achieved at room temperature, producing surfaces with roughnesses of only 20 nm. © 1999 The Electrochemical Society. All rights reserved.
2705
D. Bose, T. R. Govindan and M. Meyyappan
A comprehensive continuum model is presented for the analysis of high‐density plasma reactors widely used in semiconductor processing. The model couples plasma transport, neutral species dynamics, gas flow, heat transfer, and plasma power coupling from an external source. The governing transport equations are solved along with Maxwell's equations for a multicomponent, multi temperature system with inductively coupled power deposition. The model and code are applied to a nitrogen discharge in an inductively coupled plasma reactor, and the predictions agree well with the experimental data. The effect of self‐consistent modeling of gas flow and gas heat transfer is systematically examined and it is found to affect plasma density and uniformity at low pressures. © 1999 The Electrochemical Society. All rights reserved.
2712
Shiyang Zhu, Yiping Huang, Guoping Ru, Xinping Qu and Bingzong Li
2717
L. C. Meyer, J. W. Lee, D. Johnson, M. Huang, F. Ren, T. J. Anderson, J. R. LaRoche, J. R. Lothian, C. R. Abernathy and S. J. Pearton
Si‐doped n‐GaAs samples were exposed to inductively coupled plasma (ICP)
discharges at different chuck temperature, pressure, source powers, and rf chuck powers to simulate the effects of ion damage and hydrogen passivation during
silicon nitride deposition for GaAs ICs fabrication. The ideality factor and reverse breakdown voltage of Schottky diodes were used to characterize the plasma damages. Both ideality factor and reverse breakdown voltage increase with increasing rf chuck power and ICP power because of the reduction of free carriers due to the lattice disorder created by the ion bombardment. A similar trend was observed with increasing deposition temperature and pressure; however, this is mainly due to the passivation of Si dopants in the GaAs donor layer by hydrogen free radicals and ion bombardment damage. The high temperature process enhances the hydrogen diffusion and high pressure produces more hydrogen free radicals and deposition bias voltage increases at both conditions. © 1999 The Electrochemical Society. All rights reserved.
2720
Hwa Sung Rhee and Byung Tae Ahn
2725
Fumitoshi Sugimoto and Sigeru Okamura
The adsorption behavior of organic contaminants adsorbed onto silicon wafer surfaces was studied. Contaminants result from the presence of volatile organic contaminants in clean room environments and in plastic storage boxes. The contaminants on the wafers were collected by dissolving them in solvent and were characterized by gas chromatography‐mass spectroscopy analysis. It was found that organic contaminants increase in quantity over time. When the contaminants were examined in detail, it was found that the behavior of each contaminant varied with differences in their chemical properties. Whereas the organic contaminants having a low boiling point tended to be adsorbed immediately, those having a high boiling point tended to be adsorbed over a longer exposure time. It is assumed that the organic contaminants having a low boiling point were being replaced by those with a higher boiling point. © 1999 The Electrochemical Society. All rights reserved.
2730
A. A. Ayón, R. A. Braff, R. Bayt, H. H. Sawin and M. A. Schmidt
We present the effects of applied coil power on silicon etching in a high density inductively coupled plasma etcher in both the isotropic and anisotropic regimes. The experimentally obtained response surfaces were generated while changing four etching variables for the isotropic case and eight etching variables for the anisotropic case. The measured performance contained in this report serves as a guide to tailor etching conditions to produce isotropic profiles while etching with pure
, and also to optimize anisotropic profiles when using time multiplexed deep etching. The response surfaces contained herein are useful for micromachining high aspect ratio structures. © 1999 The Electrochemical Society. All rights reserved.
2737
S. Hénaux, F. Mondon, F. Gusella, I. Kling and G. Reimbold
This paper focuses on doping type and doping level characterization of silicon‐on‐insulator wafers prior to device fabrication. The ability of the point‐contact pseudo‐metal‐oxide‐semiconductor transistor to analyze background doping is investigated thoroughly both theoretically and through a comparison with secondary ion mass spectroscopy on intentionally doped wafers. A new method using mercury contacts is proposed to determine the semiconductor type for extremely low doping levels. No sample preparation is needed and unambiguous results are obtained. The physical basis of the measurement is investigated and the method is demonstrated on bulk and silicon‐on‐insulator wafers. © 1999 The Electrochemical Society. All rights reserved.
2744
Y. C. Kang, S. B. Park, I. W. Lenggoro and K. Okuyama
The blue phosphor
particles with sphericity and nonaggregation was prepared by high‐temperature spray pyrolysis. Characteristics of the as‐prepared and the post‐treated particles such as crystallinity, morphology, and luminescence were investigated. The as‐prepared particles at 1200°C had an amorphous phase, and the sphericity of as‐prepared particles disappeared after post‐treatment at 1300°C. On the other hand, the as‐prepared particles at 1500 and 1700°C have good crystallinity of
, and its morphology was maintained after post‐treatment. The mean size of particles obtained from 0.3 M solution was 0.6 μm. The particles which were directly prepared by spray pyrolysis had higher PL intensities than those of post‐treated particles. The good morphology of particles directly prepared by spray pyrolysis caused the high luminescence intensity in comparison with the post‐treated particles. © 1999 The Electrochemical Society. All rights reserved.
2748
K. P. Lee, K. B. Jung, H. Cho, D. Kumar, S. V. Pietambaram, R. K. Singh, P. H. Hogan, K. H. Dahmen, Y. B. Hahn and S. J. Pearton
2752
Constantin Vahlas, Alina Kacheva, Michael L. Hitchman and Philippe Rocabois
2762
V. Y. Kodash and J. W. Fergus