Articles
2769
Kathryn Podolske Ta and John Newman
A reproducible hysteresis in charge‐discharge cycling of thin‐film (10–40 nm thickness) electroprecipitated nickel hydroxide electrodes was quantified. Thin‐film electrodes were prepared both with and without coprecipitated cobalt hydroxide, a common additive to nickel hydroxide electrodes. The ascending and descending branches of the hysteretic loop were determined. Experimental data were gathered using commonly employed techniques to capture electrode behavior on short‐ and long‐time scales. Cyclic voltammetry and galvanostatic discharge experiments were performed, and a macroscopic model of the nickel hydroxide solid material was constructed and used to interpret the simultaneous mass‐transfer, kinetic, and thermodynamic phenomena occurring at the nickel hydroxide intercalation electrode. The persistent hysteresis exhibited by these thin‐film electrodes cannot be due only to solid‐state mass‐transfer limitations. Agreement between calculated and experimental results is achieved with treatment of the hysteresis effect as a permanent, thermodynamic quantity. The numerical model may be applied to most rechargeable cells and is especially suited for systems which exhibit a permanent hysteretic loop or in which side reactions are prevalent. Model results agree with current and potential waveforms gathered from experiments performed with nickel hydroxide thin‐film electrodes. © 1999 The Electrochemical Society. All rights reserved.
2780
Michael E. Spahr, Petra Stoschitzki‐Bitterli, Reinhard Nesper, Otto Haas and Petr Novák
Vanadium oxide nanotubes were prepared in a modified sol‐gel reaction of vanadium oxide triisopropoxide conducted in the presence of the structurally directing hexadecylamine and followed by hydrothermal treatment. The tubes consist of concentric shells of highly crystalline vanadium oxide separated by alternating organic amine layers. The template molecules were removed without structural breakdown of the nanotubes by a combined ion‐exchange reaction and extraction process. The vanadium oxide nanotubes are redox‐active and can electrochemically insert lithium reversibly. A specific charge up to
(with respect to the oxide) was measured for
insertion into porous electrodes containing template‐free nanotubes. The specific charge decreased during cycling, indicating a loss of electroactivity. © 1999 The Electrochemical Society. All rights reserved.
2784
Karim Zaghib, Kuniaki Tatsumi, Yoshihiro Sawada, Shunichi Higuchi, Hiroshi Abe and Takashi Ohsaki
2794
Tiehua Piao, Su‐Moon Park, Chil‐Hoon Doh and Seong‐In Moon
2799
A. N. Mansour, J. McBreen and C. A. Melendres
We have measured in situ the Ni K‐edge X‐ray absorption spectra of
cathode material charged in a nonaqueous cell. The material was charged to various states of charge (i.e., Li content) which corresponded to x = 0.0, 0.12, 0.24, 0.37, 0.49, and 0.86 in
. We have determined variations in the Ni‒O and Ni‒Ni coordination numbers, bond lengths, and local disorders as well as the Ni K‐edge energies as a function of Li content. We show that in the pristine state, the composition of the material can be described by the formula
(i.e., x = 0 and
= 0.14). That is, the material consists of
(25%) and
(75%) with half the
atoms residing in Li sites and the other half in the
slabs. Upon charging, initially
is oxidized to
up to a state of charge which corresponds to x = 2
. Upon further charging to states corresponding to 2z <x≤1 − z,
is oxidized to
with fractions being dependent on the values of x and z. Analysis of the edge energies for NiO, stoichiometric
, and
as reference compounds for
,
, and
, respectively, shows a quadratic dependence for edge energy vs. oxidation state. This type of correlation is consistent with variations observed in earlier studies for some Mn reference compounds in the same range of oxidation states. Oxidation‐state determination of Ni in
as a function of state of charge (i.e., Li content or x) on the basis of edge energies yielded results which are in excellent agreement with oxidation state determinations made on the basis of the mole fractions for
,
, and
extracted from extended X‐ray absorption fine structure spectra. © 1999 The Electrochemical Society. All rights reserved.
2810
Feng Zheng and Larry R. Pederson
The phase stability of Sr‐doped
(LSM) perovskite in the La‐Sr‐Mn‐O system was investigated as a function of Sr content and A/B cation ratio. The perovskite structure changed with both Sr content and A/B cation ratio. As the Sr content was increased to 0.2 mol, the perovskite structure adopted an orthorhombic distortion. This changed to a monoclinic or hexagonal structure for 0.2 ≤ Sr ≤ 0.3 mol. When the Sr content increased to 0.3 mol, the structure reverted to orthorhombic symmetry. Data from X‐ray powder diffractometry, scanning electron microscopy, transmission electron microscopy, and energy‐dispersive X‐ray emission spectroscopy, showed that secondary phases in the La‐Sr‐Mn‐O system were underdeveloped with respect to changes of the doped Sr content, A/B cation ratio, and thermal history. X‐ray detectable minor phases present in the LSM material were
,
,
,
,
, and
. © 1999 The Electrochemical Society. All rights reserved.
2817
Feng Zheng and Larry R. Pederson
2821
Takashi Hibino, Yoshitaka Kuwahara and Shuqiang Wang
2827
S. Primdahl and M. Mogensen
Impedance spectra obtained on high‐performance
Ni/yttria stabilized zirconia (YSZ) cermet anodes at 1000°C in
gas mixtures are considered. An impedance arc with a characteristic frequency of about 10 to 100 Hz is related to finite diffusion limitation by considering the dependence on water partial pressure, apparent thermal activation, and effect of the inert gas component. By experiments in different test geometries the diffusion zone is demonstrated to be a stagnant gas layer outside the anode structure. An estimated stagnant gas layer thickness of about 1 mm is arrived at. The diffusion impedance is demonstrated to be avoidable by using a setup geometry with two coupled electrodes in direct electrical contact through opposing sides of a contacting mesh. © 1999 The Electrochemical Society. All rights reserved.
2834
M. Yoshikawa, Y. Mugikura, T. Watanabe, T. Ota and A. Suzuki
2841
Chris Yates and Jack Winnick
2845
M. Saito, K. Yamada, K. Ohashi, Y. Yasue, Y. Sogawa and T. Osaka
Electroplated CoNiFe films with a saturation flux density as high as 2.1 T are potentially useful in high‐density magnetic recording heads. We found that films electroplated at a high current density
from a bath without saccharin have a sufficient anodic pitting‐corrosion potential (−65 mV). We also found that the pitting‐corrosion potential of films electroplated under a low current density
from saccharin‐free baths have anodic pitting‐corrosion potentials of less than −300 mV. However, the corrosion resistance improved after annealing at temperatures above 100°C. The crystal‐grain boundaries in the as‐plated film that electroplated under a low current density from saccharin‐free baths are not clear (i.e., that the phase is amorphous). But the crystal grain boundaries in the annealed film are clear. Films electroplated from baths containing saccharin also have anodic pitting‐corrosion potentials of less than −300 mV. Their corrosion resistance did not improve when they were annealed at 250°C. The deterioration of the corrosion resistance is attributed to the defects that increase the face‐centered cubic (111) lattice constant. One of the most important characteristics of a highly corrosion‐resistant CoNiFe film is fine crystal structure with very few defects. © 1999 The Electrochemical Society. All rights reserved.
2849
E. McCafferty, J. P. Wightman and T. Frank Cromer
The nature of surface hydroxyls present in the native air‐formed oxide film on titanium has been studied by X‐ray photoelectron spectroscopy (XPS), variable angle XPS, and secondary ion mass spectroscopy (SIMS). The surface isoelectric point of the oxide film on titanium is 5.0, as determined from XPS measurements; and the concentration of surface hydroxyl groups on oxide‐covered titanium is
, as determined by quantitative XPS. © 1999 The Electrochemical Society. All rights reserved.
2853
Minghua Wang, Howard W. Pickering and Yuan Xu
An iteration method for computing the nonuniform potential and current distributions at a partially passivated disk electrode is introduced. The computation method is developed for a small cathode in the vicinity of a much larger anode, a situation encountered in some polarized electrochemical systems, e.g., anodic protection. It uses the finite element method allied with a trial and error technique as well as a successive boundary condition variation technique. The method was used for the study of a steel electrode immersed in a 0.5 N HAc + 0.05 N NaAc solution. The computed distributions, currents, and radius of the passive center were in good agreement with the measured values. © 1999 The Electrochemical Society. All rights reserved.
2863
E. McCafferty
The isoelectric point of the oxide‐covered aluminum surface is an important parameter in the pitting behavior of aluminum and of aluminum binary surface alloys. Contact angle measurements show that ion implantation of Ta into Al modifies the isoelectric point of the resulting oxide film to a value which is intermediate between that of
and
. The critical pitting potential is shown to be a function of the flatband potential of the oxide‐covered aluminum surface. For a series of alloys where the matrix metal (and host oxide) is held fixed, the flatband potential is a function of the isoelectric point of the oxide film on the alloy surface, which in turn is a function of the isoelectric point of the oxide of the alloying element. Thus, the critical pitting potential of a binary surface alloy is related to the isoelectric point of the oxide of the alloying element in the binary alloy. Surface alloying affects the pitting potential by (i) modifying the isoelectric point of the surface so as to change the surface charge, (ii) affecting the heat of adsorption of the chloride ion, and (iii) changing the concentration of oxygen vacancies in the oxide film. © 1999 The Electrochemical Society. All rights reserved.
2870
S. Zhang, J. De Baets, M. Vereeken, A. Vervaet and A. Van Calster
With the advent of flip chip assembly, pads to be plated on printed circuit boards (PCBs) have shrunk dramatically to around
. As a result, most commercial electroless nickel baths will fail to deposit nickel on such small micropads. In this paper, using a specially designed PCB layout, the effects of
concentration and local environment are studied. A competition mechanism between two opposite actions, the adsorption from bulk solution by diffusion and the burying by nickel deposition, is used to explain the effect of
as a catalytic inhibitor. On a constantly growing surface, the dynamic density of adsorbed
is the net result of these two opposite actions. Using this competition mechanism, the skipping problem of micropads is attributed to the combined result of nonlinear diffusion and high concentration of
in the bulk solution. This competition mechanism also gives a new explanation for the effect of potential pinning. In the case of potential pinning, galvanic effect by electrons flowing from one area to another only exists during the initial period of nickel deposition. Once it is started, nickel deposition on any area is maintained by the electroless process, and hence, is actually self‐supporting, By reducing the bulk concentration of
to a lower range in a commercial bath, we have realized consistent nickel plating on micropads as fine as 50 μm in diameter. © 1999 The Electrochemical Society. All rights reserved.
2876
S. Z. Chu, M. Sakairi, I. Saeki and H. Takahashi
The mechanism of direct Ni‐P electroless deposition on aluminum by pulsed yttrium aluminum garnet (YAG) laser irradiation in
solution was investigated by X‐ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) with energy‐dispersive X‐ray (EDX) analysis. Aluminum specimens covered with porous anodic oxide films were irradiated with a pulsed YAG laser in solutions containing
,
,
, or
ions, and then localized Ni‐P electroless plating was attempted at the laser irradiated area in
solution. It was found that laser irradiation in solutions containing
,
, or
ions causes the deposition of small metallic particles of Pd, Cu, or Ni at the laser‐irradiated area on the aluminum surface which was exposed to the solution after removal of anodic oxide film. The deposition of the metals is due to a redox reaction between the aluminum substrate and the
,
, or
ions. During laser irradiation in
solution, Ni‐P and Ni were deposited by redox reactions between
and
as well as between
and Al. Palladium and nickel (Ni‐P) particles deposited during the laser irradiation acted as catalytic centers for the subsequent Ni‐P electroless plating, while Cu particles did not promote the electroless plating. © 1999 The Electrochemical Society. All rights reserved.
2886
N. Zech, E. J. Podlaha and D. Landolt
2892
N. Zech, E. J. Podlaha and D. Landolt
A mathematical model for anomalous codeposition of iron group metals is presented which describes effects of inhibition and enhancement observed experimentally during codeposition of FeNi, NiCo, and FeCo alloys. The model assumes three parallel reaction paths each one proceeding in two consecutive steps and it takes into account the effect of mass transport. The model assumes that deposition involves an adsorbed reaction intermediate containing both metal ions in partly reduced form. This reaction intermediate is responsible for both the inhibition of the more noble species and the enhancement of the less noble species. Differences in the deposition behavior of the three alloy systems considered are due to differences in the surface coverage of the mixed reaction intermediate. The theoretical predictions of the model are compared with experimental data obtained under well‐defined mass transport and current distribution conditions. The model can simulate in a satisfactory way the observed effects of inhibition and enhancement due to codeposition and it predicts correctly the influence of mass transport. It is less successful in the simulation of the influence of the concentration of reacting species. Possible reasons for this behavior are discussed and research directions for improving the model are outlined. © 1999 The Electrochemical Society. All rights reserved.
2901
B. S. MacGibbon, A. A. Busnaina and B. Fardi
Thermophoresis has a direct impact on the amount of particulate deposition on the substrate due to the temperature gradients present near the substrate in a chemical vapor deposition reactor. The effect of thermophoresis on the particle transport and deposition in the reactor is predicted and verified experimentally. Different particle concentrations and sizes are considered. In addition, the motion of these particles according to the thermal gradients in the reactor is examined. The numerical and experimental results show that the particle deposition on the wafer decreases exponentially as the wafer temperature increases or the showerhead temperature decreases. © 1999 The Electrochemical Society. All rights reserved.
2906
P. R. Holmes, T. A. Fowler and F. K. Crundwell
In many of the experiments reported in the literature on the leaching of pyrite by Thiobacillus ferrooxidans, the concentrations of ferric and ferrous ions in the presence of bacteria differ significantly from experiments conducted in their absence. In addition, these concentrations change throughout the course of the experiment. This makes it difficult to determine whether the presence of bacteria increases the rate of leaching above that for chemical leaching at the same solution conditions. We have designed an experimental apparatus to overcome this problem. This apparatus controls the redox potential in one compartment of an electrolytic cell by manipulating the current to the cell. In this manner, the concentrations of ferrous and ferric ions are maintained at their initial values for the duration of the experiment. Two types of experiments are reported in this paper. In the first, pyrite electrodes were exposed to solutions of the same bulk conditions in the presence and absence of bacteria, and their mixed potentials were determined. In the second, particulate pyrite was leached with and without bacteria to determine the effect that bacteria have on the rate of leaching. The mixed potential of bacterially dissolved pyrite decreases as microcolonies and biofilms form on the surface of pyrite electrode over a 14 day period. On the other hand, the mixed potential of chemically dissolved pyrite is constant over the same period. The results of the leaching experiments show that Thiobacillus ferrooxidans enhances the rate of leaching above that found in the absence of bacteria at the same conditions in solution. An electrochemical model of pyrite dissolution is derived that describes the mixed potential and the kinetics of pyrite leaching. This analysis indicates that the decrease in mixed potential and the increase in the leaching rate in the presence of bacteria are due to an increase in the pH at the surface. © 1999 The Electrochemical Society. All rights reserved.
2913
Z. Mekhalif, J. Delhalle, P. Lang, F. Garnier and R. Caudano
2919
F. Girard, R. Izquierdo, E. Quenneville, S. T. Bah, M. Paleologou, M. Meunier, D. Ivanov and A. Yelon
A RAIPORE polymeric cation‐selective membrane was modified by deposition of a thin film of NASICON, a sodium superionic conducting ceramic, using pulsed laser deposition. The composite membrane was incorporated into an electrolysis system for the production of sodium hydroxide and sulfuric acid from sodium sulfate. Its performance was compared to the unmodified polymeric base membrane. The composite membrane showed a significantly higher selectivity for sodium over hydrogen ions compared to the unmodified polymeric base membrane, resulting in a higher current efficiency and a lower energy consumption for the production of sodium hydroxide. The composite membrane was also found to be more resistant to fouling by ferric ion as compared to the polymeric membrane. Neither membrane was fouled by calcium or magnesium. The selectivity of the composite membrane for sodium over potassium ions was not found to improve by the deposition of the ceramic layer. © 1999 The Electrochemical Society. All rights reserved.
2925
C. Bock and B. MacDougall
2933
Cécile Vallières and Michael Matlosz
A multisectioned flow‐through porous electrode, consisting of alternating conducting and insulating sections, was designed, built, and tested for the electrosynthesis of D‐arabinose in aqueous solution. The laboratory prototype, consisting of ten independent porous graphite slices each of 5 mm thickness, can be adapted by external electrical connection to allow both traditional and sectioned operations to be run in a single device. The experimental study in this work focuses on use of the multisectioned arrangement to improve current‐distribution uniformity in the porous‐electrode reactor. A model electrosynthesis system, consisting of oxidation of sodium gluconate to D‐arabinose in competition with the parallel reaction of oxygen evolution, has been chosen for investigation. Measurements in the sectioned electrode show that the performance, expressed in terms of current efficiency for gluconate oxidation, increases significantly with an increase in the number of sections. A comparison of predicted theoretical performance with experimental measurements on the ten‐section prototype has been used to extrapolate the performance of the sectioned electrode to configurations with larger numbers of sections. Extrapolation indicates that optimal performance in the 5 cm electrode can be achieved with fewer than 100 sections, a design that is feasible to construct with modern microfabrication technology. © 1999 The Electrochemical Society. All rights reserved.
2940
F. Zou and D. Thierry
An attempt to assess the influence of diffusion on localized impedance measurements by means of probe method is presented. The influence has been demonstrated and discussed by experiments and computer simulations. When the probe is positioned within the diffusion layer, the measured localized impedance spectra could be different from the conventional electrochemical impedance measurements due to the heterogeneous concentration distribution. The deviations can be dc density‐dependent when the variation of conductivity is the predominant reason of the influence. When the influence of diffusion is predominately due to the redox potential difference at the probe,the deviation can be less dc‐dependent. The influence at low frequency range is more serious than at high frequency range. © 1999 The Electrochemical Society. All rights reserved.
2948
Y. Nigara, K. Kawamura, T. Kawada, J. Mizusaki and M. Ishigame
It was found that the sintered
, which was not perovskite‐type but fluorite‐type, permeated hydrogen under
atmosphere at 1050–1800 K. Three tube‐shaped specimens (ϕ 0.287 × 0.894 cm) (SP I, SP II, SP), the lengths of which were 1.40, 0.37, and 1.45 cm, were prepared. The nonexistence of micropores in specimens was confirmed by supplement of
to the outside of SP at 1650–1820 K.
was supplied to the outsides of SP I and SP II and Ar gas wasallowed to flow to the inside of them. The flow rate to SP I was
, and the flow to SP II was controlled so that the hydrogen concentrations measured by a gas chromatograph were of the same value. After the calculation of
,
, and
concentrations in an equilibrium state inside and outside SP I and SP II and the elimination of mechanically leaked
and permeated hydrogen through the supporting materials (Pt rings, alumina tube, and disk), the atomic hydrogen permeability,
, was determined. The hydrogen partial pressures in the outside and inside were
and
to 1.53 × 10−3 atm at 1050–1800 K. Log
increases with rising temperature, T, while it is not proportional to 1/T. As the electronic conduction in
is considerably higher at low oxygen partial pressure, there is a possibility that
is an electron‐proton mixed conductor under
atmosphere at high temperatures. © 1999 The Electrochemical Society. All rights reserved.
2954
Yongchun Zhu, Yujuan Lü, Guangjin Cheng and Shaojun Dong
The adsorption of an electroinactive product greatly influences an irreversible electrochemical reaction in three ways, including self‐block, self‐inhibition, and self‐acceleration, and changes not only the heterogeneous electron‐transfer rate constant but also the modified formal potential and electron‐transfer coefficient of the electrochemical reaction. In order to study these adsorption effects, a double logarithmic method was suggested to be used in processing the potential‐controlled thin layer spectroelectrochemical data. The result shows three types of double logarithmic plots for three kinds of adsorption effects. These double logarithmic plots can be a diagnostic criterion of the adsorption effects and enable us to determine some thermodynamic and kinetic parameters. The combination of nonlinear regression with double logarithmic method is a convenient way to examine the suggested mechanism and to extract more information from the limited experimental data. Some examples are given to test the theoretical results. © 1999 The Electrochemical Society. All rights reserved.
2959
Heidi B. Martin, Alberto Argoitia, John C. Angus and Uziel Landau
2965
Gary Binyamin and Adam Heller
2968
V. Lehmann and S. Ronnebeck
The dependence of the morphology of macropores in p‐type silicon electrodes on formation parameters such as substrate doping density, electrolyte composition, and applied current density is investigated. The results are compared with the well‐understood case of electrochemical macropore formation on n‐type silicon electrodes. A growth model is derived in which pore formation is shown to be a consequence of charge‐transfer mechanisms in a Schottky diode applied to a nonplanar interface. © 1999 The Electrochemical Society. All rights reserved.
2976
P. Holtappels, I. C. Vinke, L. G. J. de Haart and U. Stimming
The impedance of nickel‐zirconia cermet electrodes at the open‐circuit potential was investigated as a function of temperature for different partial pressures of hydrogen and water. The impedance spectra for the hydrogen/water reaction show three apparent relaxation frequencies that are influenced by the temperature. The data are analyzed using an equivalent circuit representing two parallel reaction pathways which are attributed to (i) a reaction at the triple‐phase boundary involving charge transfer and adsorption and (ii) a diffusion branch described by a resistor in series with a Warburg impedance. At temperatures below 890°C, a charge‐transfer resistance dominates the real part of the impedance. A possible contribution of adsorption in the impedance spectra at higher temperatures is discussed. The diffusion branch is tentatively attributed to an electrochemical reaction in the area of the nickel/electrolyte interface, which is limited by diffusion of protons in the electrolyte phase. The activation enthalpy calculated for this process is between 120 and
. © 1999 The Electrochemical Society. All rights reserved.
2983
Tomás Harrington and Derek Pletcher
The removal of several organics (phenol, aniline, acetic acid, formaldehyde, and three azo dyes) from aqueous solutions (pH 2) containing Fe(II) and using hydrogen peroxide produced by the reduction of oxygen at a gas‐diffusion electrode is demonstrated. It is shown that chemical oxygen demand of solutions containing such organics may be reduced by >90% with a current efficiency >50%, leading to acceptable energy consumptions. The approach also clearly has considerable generality. The voltammetry of the gas diffusion electrodes, fabricated by screen printing an XC72‐R carbon powder/polytetrafluorene active layer on a carbon fiber paper support is also reported and discussed. © 1999 The Electrochemical Society. All rights reserved.
2990
E. S. Kooij, A. T. M. van Gogh and R. Griessen
We describe an experimental method for in situ resistivity measurements during the electrochemical hydrogen loading of thin, switchable metal hydride films. Using an oxygen‐free electrolyte we are able to measure the hydrogen concentration in the films quantitatively and to determine the pressure‐composition isotherms and the hydrogen concentration dependence of the resistivity. Furthermore, the optical properties can be investigated by simultaneous transmission and reflection spectroscopy. The power of these in situ measurements is discussed on the basis of results obtained on
films; possibilities for additional experiments are briefly described. © 1999 The Electrochemical Society. All rights reserved.
2995
Peter Koronaios and Robert A. Osteryoung
3000
Yongchun Zhu, Guangjin Cheng and Shaojun Dong
A simple double logarithmic method in potential‐controlled thin‐layer spectroelectrochemistry for an irreversible electrochemical process has been studied by numerical analysis and examined by experimental examples. This simple algorithm has a novel function offering some important information about the mechanism of a complex electrochemical process directly from a limited amount of potential‐spectrum data, and can be used to distinguish different reaction mechanisms such as E, EC, EE, as well as to determine the electron‐transfer coefficient, α, and the kinetically modified
. Combination of the double logarithmic method with nonlinear regression provides a powerful tool to examine the proposed mechanism and also to estimate other thermodynamic and kinetic parameters. © 1999 The Electrochemical Society. All rights reserved.
3004
Wen‐Chang Chen, Shu‐Chun Lin, Bau‐Tong Dai and Ming‐Shih Tsai
In the study, the film properties and chemical mechanical polishing (CMP) characteristics of the low‐dielectric‐constant materials hydrogen silsesquioxane (HSQ) and methyl silsesquioxane (MSQ) were presented. The Fourier transform infrared spectra, refractive index, dielectric constant, and atomic force microscopy results showed the successful preparation of the HSQ and MSQ films. The CMP characteristics of both materials were studied by two different
slurries, A‐1 and B‐1. Our results showed that the CMP removal rate and nonuniformity increased with increasing the slurry solid content. The removal rate of the polished HSQ film was much larger than that of the polished MSQ film due to the hydrophobic surface of the MSQ film. The removal rate using the A‐1 slurry was larger than the B‐1 slurry for polishing both films. This result can be explained from the consideration of the isoelectric point and the electrostatic force between the abrasive surface and the film surface. The downforce pressure of the CMP process also showed a significant effect on the removal rate and the nonuniformity of the polished HSQ film. © 1999 The Electrochemical Society. All rights reserved.
3009
Khalid Yacoubi, Catherine Azzaro‐Pantel, E. Scheid and Jean‐Pierre Couderc
This paper, Part I of two, presents the results of a study combining experimental and modeling approaches of low pressure chemical vapor deposition (LPCVD) of silicon nitride from a silane‐ammonia mixture. The experimental study consists in a reduced number of runs, chosen in order to identify the main features of the deposition process, i.e., marked nonuniformities at the wafer edge both in thickness and in Si/N composition. It is then shown that a complex gas‐phase mechanism may be responsible for the observed physicochemical phenomena. A gaseous reaction model is thus proposed for a silane‐ammonia mixture under typical low pressure CVD conditions. A complete reaction scheme is first studied. A thorough quantum Rice Ramsberger Kassel (QRRK) analysis compensated for the lack of kinetic information in the gas phase and allowed the identification of kinetic constants for uniand bimolecular reactions. Its appropriateness is examined with one‐dimensional nonsteady computations. A combined analysis of these calculations and of the QRRK results shows that the reaction model could be simplified, thus leading to a reduced reaction set reproducing the essential features of the full mechanism experimentally observed, which involves six species with two silylamine intermediates
and
. In Part II of this article series, this mechanism is integrated in a 2‐D model of LPCVD reactors, previously developed in the laboratory (called CVD2) and adapted to this kind of deposition, taking into account hydrodynamics, mass transport, and chemical reactions. © 1999 The Electrochemical Society. All rights reserved.
3018
Khalid Yacoubi, Catherine Azzaro‐Pantel and Jean‐Pierre Couderc
This paper, Part II of this series of two articles, is devoted to two‐dimensional modeling of silicon nitride low pressure chemical vapor deposition from a silane‐ammonia mixture. In that aim, the CVD2 model previously developed in our laboratory, which takes into account hydrodynamics, mass transport, and chemical reactions, is adapted to this special kind of deposition. The gas phase mechanism described in Part I is integrated in the model. The concentration profiles of
,
,
,
,
, and
have been computed and the contribution of the different species to deposition rate have been evaluated. The results obtained confirm the importance of the entrance zone length of the reactor, which conditions the formation of the stable species
, generating
and
, which are responsible for the strong overthicknesses observed at the wafer periphery. © 1999 The Electrochemical Society. All rights reserved.
3028
Dong‐Hun Lee, Tae‐Yeon Seong, Man‐Ho Cho and Chung‐Nam Whang
3032
Xidong Chen and J. M. Gibson
3039
Vladislav Y. Vassiliev, Jia Zhen Zheng, Shiau Khee Tang, Wei Lu, Ji Hua and Yih Shung Lin
Growth kinetics of borophosphosilicate glass (BPSG) films prepared by the chemical reaction of tetraethylorthosilicate (TEOS), triethylborate, and triethylphosphate, with ozone‐oxygen mixture has been studied using a single‐wafer deposition chamber at 373–458°C under reduced pressure or subatmospheric pressure condition (SABPSG). Based on the comparison of the effective reaction rate constants and other kinetic features, the similarity of BPSG deposition kinetic for different types of precursors and deposition conditions are shown. Fourier transform infrared spectroscopy, X‐ray fluorescence analysis, secondary ion mass spectrometry, stress measurement, optical microscopy, scanning electron microscopy, atomic force microscopy, surface laser scanning, capacitance‐voltage, current voltage, and surface charge analysis techniques have been used for the characterization of SABPSG film properties. Moisture absorption and surface defect formation phenomena have been studied for both as‐deposited and furnace annealed films with boron and phosphorus ranging from 3 to 6 wt %. The liquid state, solid state, and crystalline BPSG surface defects have been characterized and their relationships have been shown. A multipath and multistep reaction mechanism scheme of TEOS‐ozone BPSG deposition process with the formation of active intermediate products, a scheme of porous TEOS‐ozone BPSG film with embedded dopant‐rich clusters, and a scheme of defect formation and growth on BPSG films are discussed. Empirical equations of quantitatively optimized BPSG dopant concentration range are presented by taking into account flow properties, defect formation, and moisture absorption processes in the film. © 1999 The Electrochemical Society. All rights reserved.
3052
Yasuhiro Shimizu, Yoshihiro Akai, Takeo Hyodo, Yuji Takao and Makoto Egashira
3058
C. Gerardi, R. Zonca, B. Crivelli and M. Alessandri
This work reports on the impact of nitric oxide (NO) nitridation on physical and electrical properties of thin steam gate or tunnel oxides. The oxides (∼7 nm) have been annealed in NO ambient under different annealing times and NO fluxes, and for comparison in nitrous oxide
. Nitridation causes nitrogen to pile up near the
interface, producing interface regions with quite different physical and chemical properties according to whether NO or
is used. Secondary ion mass spectroscopy, X‐ray photoelectron spectroscopy, and atomic force microscopy measurements, combined with etch‐rate experiments, show that in the case of NO, nitrogen is built up very close to the interface with a remarkably higher peak (at a lower thermal budget than
) and a narrower distribution, whereas with
, nitrogen distribution is broadened with a lower peak slightly displaced from the interface. The different behavior under reoxidation of NO‐ and
samples confirms the results mentioned previously. Physical analysis shows that the nitrided region is divided into an N‐rich region at the interface with predominant Si‐N bonds and a transition region further from the interface with a lower N content and fewer silicon nitride bonds. The two regions depend on the annealing conditions: the higher exposure produces a bigger N‐rich and a smaller transition region. Electrical characterization shows that NO nitridation improves the oxide resistance to electrical stress for substrate carrier injection. However, a strong NO treatment degrades the oxide robustness during gate injection. Furthermore, a correlation between positive and negative trapping with transition and N‐rich regions is observed under substrate injection conditions. Finally, the role of NO nitridation as boron diffusion barrier in surface p‐channel metal‐oxide semiconductor field effect transistor devices was investigated, showing that the higher nitrogen amount at the
interface the lower the B concentration reaching the silicon substrate. © 1999 The Electrochemical Society. All rights reserved.
3065
Takahisa Yamaha and Fujio Masuoka
This paper reports results on an investigation of the influence of titanium film in interconnects on incomplete transistor annealing. Annealing damage may be impeded when titanium directly overlays transistors. This may be due to not only gettering of hydrogen by titanium films but also to retarding hydrogen diffusion of the interlayer between the gate electrode of transistors and the titanium‐containing interconnects in boron phosphosilicate glass. The hydrogen diffusion coefficient in the boron phosphosilicate glass film was approximately
at 400°C, which is three orders of magnitude smaller than that in the thermal oxide. © 1999 The Electrochemical Society. All rights reserved.
3070
Patricia A. O'Neil, Mehmet C. Öztürk, Alan D. Batchelor, David Venables, Meimei Xu and Dennis M. Maher
In this report, we present results on the low thermal budget deposition of selective silicon epitaxy on heavily
implanted substrates using
and
, in an ultrahigh vacuum rapid thermal chemical vapor deposition reactor. Si growth kinetics, selectivity to
, dopant incorporation, and epitaxial quality have been investigated for varying implant dose conditions and varying levels of chlorine during processing. Contrary to published reports, no significant selectivity degradation mechanism has been observed for oxides implanted, and therefore, damaged by
ions. Additionally, with heavily implanted boron substrates no reduction in silicon growth occurred despite the presence of a hydrophilic substrate surface just prior to epitaxial growth. Although the hydrophilic surface did not affect the silicon growth rate, the epitaxial defect density did increase with increasing implant dose and chlorine flow rate during processing. The nature of these defects has been studied using atomic force microscopy and transmission electron microscopy. The incorporation of boron into the deposited epitaxial films has been investigated and abrupt profiles or intentionally diffuse structures were achieved through variation of the process sequence and annealing conditions. © 1999 The Electrochemical Society. All rights reserved.
3079
Patricia A. O'Neil, Mehmet C. Öztürk, Alan D. Batchelor, David Venables and Dennis M. Maher
In this report, we present results on the low thermal budget deposition of selective silicon epitaxy on heavily arsenic implanted substrates using
and
in an ultrahigh vacuum rapid thermal chemical vapor deposition reactor. The selectivity of silicon to
as well as the silicon growth kinetics, epitaxial quality, and dopant incorporation for varying substrate implant dose conditions and varying levels of chlorine during processing were investigated. We demonstrate that an increase in the arsenic implant dose can reduce the silicon growth by means of an inherent incubation time for deposition occurring in a chlorinated ambient. The extent to which the silicon growth suppression occurs, however, can be lessened by specific changes in the system conditions, and therefore, growth reductions due to arsenic can be minimized. In addition to changes in the silicon growth kinetics, arsenic implanted substrates have demonstrated a tendency to degrade the surface morphology and enhance the density of defects within the deposited silicon epitaxial films. Furthermore, by depositing the silicon film immediately following implantation and prior to any high temperature anneal, movement of arsenic into the deposited silicon layers has been observed at growth temperatures as low as 800°C. Therefore, the incorporation of arsenic into the deposited epitaxial films has been found to be controllable such that abrupt profiles or intentional diffuse structures can be achieved by variation of the process sequence and the annealing conditions. © 1999 The Electrochemical Society. All rights reserved.
3087
David H. Matthiesen, Kristi Davidson and William A. Arnold
The effect of the action of shearing a column of molten gallium (Ga) doped germanium (Ge) on the gallium concentration field in a shear cell segment was experimentally investigated using a physical model. A physical model is an experimental system that is different from the system of interest but connected by scaling relations. Water was used as the fluid in the physical model in place of the molten germanium, and methylene blue dye was used as a tracer in place of the gallium dopant to determine the extent of mixing. Two adjacent cylindrical fluid segments in a capillary of a shear cell were studied with the physical model. These fluid segment dimensions were scaled by a factor of seven for the physical model, since the kinematic viscosity of water at 22.6°C is seven times that of Ge at 950°C. A small amount of mixing between adjacent segments was measured due to the initial fluid‐fluid shear. The mass transfer between the top and bottom segments of the physical model during the fluid‐fluid shear was found to be less than 2% for all shear rates in the range 0.1–2.0 cm/s. The average mass transfer between adjacent segments due to the fluid‐fluid shear in that shearing range was 1.2%. © 1999 The Electrochemical Society. All rights reserved.
3092
Kow‐Ming Chang, I‐Chung Deng and Hong‐Yi Lin
In this study, amorphous‐like tungsten films were deposited by a chemical vapor deposition (CVD) process. The deposited film has shown reduced resistance compared with
, and it also blocked the fluorine atoms from diffusing into the gate oxide. Furthermore, when the amorphous‐like tungsten film was deposited prior to a typical CVD tungsten film with a columnar structure, it not only showed excellent barrier characteristics in impeding fluorine impurities, but its resistance was also substantially lower than a single layer of a‐W film. It is also found in our work that a bilayer film containing typical CVD tungsten/amorphous‐like CVD tungsten is a better wordline structure due to its extraordinarily low resistivity and low fluorine contamination. © 1999 The Electrochemical Society. All rights reserved.
3097
A. Ruf, A. Rucki, H. Cerva, O. Gehring and J. Pahlitzsch
Electron energy loss spectroscopy (EELS) on 16M dynamic random access memory (DRAM) device structures is used to study locally the diffusion of oxygen in the physically vapor deposited (PVD)‐Ti chemical vapor deposition (CVD)‐TiN tungsten liner films. These results are correlated to the electrical contact resistance of 1000 tungsten contact chains on
silicon areas depending on different titanium thickness at the bottom of the contact hole and on the use of a liner anneal around 600°C. It is shown that the local diffusion of oxygen tracked with the EEL spectroscopy is consistent with Auger analysis on blanked films and can explain the different electrical results of the 16M DRAM devices. From this explanation it can be concluded that for a microelectronic processing application the use of CVD‐TiN as the barrier in tungsten plug application with an air break between the PVD‐Ti and CVD‐TiN deposition is only acceptable if enough titanium is available to buffer the oxygen from the native titanium oxide. © 1999 The Electrochemical Society. All rights reserved.
3101
Jae‐Chang Lee, Eun‐Suck Choi, Soon‐Gil Yoon, Dong‐Soo Yoon and Hong‐Koo Baik
3105
Jun‐ichi Nishizawa, Akihiko Murai and Yutaka Oyama
3110
Takashi Unagami
3114
H. M. Ranpura, D. H. Butler, L‐H. Chang, C. J. Tracy and S. P. Beaudoin
Removal of platinum sidewall redepositions formed due to patterning of electrodes during reactive ion etching for an embedded dynamic random access memory project has been investigated. During etching of these devices, nonvolatile etch products commonly deposit onto the pattern sidewall. Removal of these residues without damaging other exposed materials is a challenging process. A mixture of argon and chlorine plasma was used to etch the platinum electrodes used in this study. Following the etching step the wafers were processed in an oxygen plasma (ashed) to remove the photoresist on the wafer. The effectiveness of various postash‐cleaning methods was investigated. Results are presented for wafers that were heated at different temperatures for varying times in different ambients, wafers that were cleaned in aqueous hydrochloric acid of varying concentrations, and wafers that were cleaned in a 40 kHz ultrasonic bath in water, in aqueous hydrochloric acid, and in aqueous ammonium hydroxide. At the conditions studied, it was determined that dissolution of the residues was not the controlling removal mechanism. Rather, a combination of dissolution and physical displacement appeared to control the cleaning process. Specifically, the application of ultrasonic energy to baths of 6 M hydrochloric acid provided the best cleaning results. © 1999 The Electrochemical Society. All rights reserved.
3119
Myoung Seok Kwon and Jeong Yong Lee
3124
J. A. Bardwell, M. W. C. Dharma‐wardana, B. Leathem, S. Moisa, J. B. Webb and B. Tam
An infrared spectroscopic technique has been developed for the characterization of GaN epitaxially grown thin films on sapphire substrates. The technique is complementary to Raman measurements, and provides information on the longitudinal (LO) and transverse optical modes of GaN, and, for thin GaN films, the sapphire substrate. In addition, the free carrier concentration of the GaN can be characterized by analyzing the LO phonon‐plasmon coupled mode present in doped samples. For lightly doped films, the GaN film thickness is easily obtained from the Fabry‐Perot fringes present in the spectra. © 1999 The Electrochemical Society. All rights reserved.
3128
Kyoung‐Wook Min, Sun‐il Mho and In‐Hyeong Yeo
3134
S. K. Saha, R. S. Howell and M. K. Hatalis
Reaction mechanisms within aluminum‐indium tin oxide (Al‐ITO) metallization schemes were investigated in this work using X‐ray photoelectron spectroscopy and X‐ray diffraction. Examination of Al‐ITO, aluminum‐nickel‐indium tin oxide (Al‐Ni‐ITO), and aluminum‐cobalt‐indium tin oxide (Al‐Co‐ITO) interfaces reveals that considerable atomic rearrangement at the ITO interface with Al or with barrier layer transition (CO or Ni) metals occurs due to reaction. Metal‐oxygen bonds in crystalline ITO are broken and the interface is rearranged. In Al‐Co‐ITO stacks, reduced intermetallic species were detected at the Co‐ITO interface. In Al‐Ni‐‐ITO stacks, such species were not detected at the Ni‐ITO interface, although
formed at the Al‐Ni interface. These reactions within metallization stacks are important because they determine the electrical quality of ITO contacts with Al alloy data lines in polysilicon thin film transistor displays. © 1999 The Electrochemical Society. All rights reserved.
3139
P. Tägtström, P. Maårtensson, U. Jansson and J.‐O. Carlsson