ELECTROCHEMICAL SOCIETY LETTERS
L135
Qi Feng, Hirofumi Kanoh, Kenta Ooi, Masato Tani and Yoshifumi Nakacho
L137
Q. ‐Y. Tong, C. B. Eom, U. Gösele and A. F. Hebard
L139
Hideo Akiya, Shuji Kuwano, Tohru Matsumoto, Hisashi Muraoka, Manabu Itsumi and Norikuni Yabumoto
Effects of chelating agent additions to an
wet cleaning solution are examined in terms of metallic contamination on Si surfaces. While ethylenediaminetetraacetic acid and other well‐known chelating agents have been shown to reduce Fe adsorption onto an Si surface only by one third, adding a phosphonic acid chelating agent at a concentration of only 1 ppm reduces Fe and Ca contamination by more than one order of magnitude and increases dielectric strength of 11 nm thin oxide.
TECHNICAL PAPERS
Electrochemical Science and Technology
2579
Minoru Inaba, Zempachi Ogumi and Zen‐ichiro Takehara
Solid polymer electrolyte (SPE®) composite electrodes using a perfluorinated ion‐exchange membrane (Nafion®), which is known to be microscopically separated into hydrophilic and hydrophobic domains, were prepared. VariousN,N′‐dialkyl‐4‐4′‐bipyridinium salts (viologens) were incorporated in the SPE composite electrodes as phase transfer mediators. Electrochemical debromination of meso‐1,2‐dibromo‐1,2‐diphenylethane was carried out on the SPE composite electrodes. The results were compared with those obtained in an emulsion system consisting of water and dichloromethane. Of the viologen compounds tested, propyl viologen was the most effective mediator for the SPE composite electrode, while octyl viologen dibromide was the most effective mediator in the emulsion system. The active species for the debromination in the emulsion system was shown to be a doubly reduced neutral form of viologen that was generated by the disproportionation of cation radicals. The disproportionation constant,
, of octyl viologen cation radical in a two‐phase system consisting of water and dichloromethane was estimated to be 809. The reaction mechanism on the SPE composite electrode was discussed, and it was considered that the active species was generated by disproportionation at the microscopically heterogeneous interface between the hydrophilic and hydrophobic domains of the Nafion.
2587
M. L. Kronenberg, B. J. Stein and B. P. Codd
2590
Nenad M. Marković and Philip N. Ross Jr.
2599
Davor P. Sutija and Charles W. Tobias
Mass‐transport enhancement by rising single and multiple bubble streams was monitored on a vertical electrode incorporating a mosaic of
sensing elements. Limiting current measurements of the reduction of ferric to ferrous sulfate revealed the presence of two distinct mechanisms: surface renewal is effective within a swath of five bubble diameters, while macroscopic laminar flows induced by rising bubbles contribute weaker enhancement over a wider path. Enhancement caused by a sheath of multiple side‐by‐side bubble streams can be well represented by the linear superposition of the effect of single streams. Generally, at equivalent volumetric rates, small bubbles are more effective than larger ones in reducing mass‐transfer resistance to the underlying surface.
2608
L. Torsi, E. De Giglio, L. Sabbatini and P. G. Zambonin
An electroanalytical investigation of the polybithiophene (PBT) band structure has been performed through the study of the voltammetric response of redox systems like ferrocene
and p‐benzoquinone (p‐BQ) at Pt/PBT working electrode The
response suggests a semiconducting behavior of the PBT polymer and the p‐BQ voltammetric response can be used to indirectly test modifications of the polymer band structure occurring when the polymer is overoxidized; in particular the presence of states in the middle of the bandgap can be inferred.
2611
Takahisa Shodai, Boone B. Owens, Hideaki Ohtsuka and Jun‐ich Yamaki
2614
V. V. Viswanathan and A. J. Salkind
Oxygen recombination in a positive‐limited‐sealed Ni‐Cd cell was investigated. The electrodes were made by electrochemical impregnation of nickel fiber substrates. The negative electrode capacity was 1.7 times that of the positive electrode capacity, thus preventing hydrogen evolution during overcharge. A model was developed to compute the recombination parameters during charge and overcharge of the positive‐electrode‐limited sealed Ni‐Cd cell. The model was used to study the effect of electrolyte saturation level, initial state of charge of the positive electrodes, and charge rate on recombination kinetics in sealed Ni‐Cd cells. A comparison of the recombination rate at rest was made with that during overcharge.
2624
Chien‐Hsin Yang and Ten‐Chin Wen
Copolymerization of 2,5‐diaminobenzensulfonic acid (DABSA) and aniline (AN) was performed electrochemically by cyclic voltammetry on
titanium electrodes in 1M
. The copolymerization rate is strongly dependent on the amount of DABSA in the comonomer feed. The compositions of the copolymeric films were determined by x‐ray photoelectron spectroscopy and were controlled by changing comonomer feed ratios. The copolymer compositions can be expressed in terms of comonomer feed ratios by a simple copolymer model showing that the reactivity ratio of aniline increases by increasing the amount of DABSA in the comonomer feed. The composite film of DABSA‐AN copolymer with waterborne polyurethane was prepared and its conductivity was measured for comparing the effect of DABSA in the comonomer feed. Scanning electron microscope (SEM) photographs show that there exist clear differences in morphology of the polymer films at various DABSA concentrations.
2633
D. G. Kolman and J. R. Scully
2642
Charles L. Lloyd and James B. Gilbert II
Cyclic voltammetry experiments have been performed on lithium sulfide in a lithium fluoride electrolyte at 1161 K using a graphite working electrode and a platinum quasi‐reference electrode. Two distinct oxidation mechanisms are observed for the sulfide ions. The first oxidation produces sulfur and at a higher potential a disulfide species is proposed to have formed. Both oxidations appear to be reversible and diffusion controlled.
2645
David J. Ellerbrock and Digby D. Macdonald
Pits are found to nucleate on solid gallium in buffered chloride solutions, and we propose that the pits nucleate from blisters that form beneath the passive film on the metal substrate. The proposed association of pitting with blister formation is accounted for by the point defect model for the growth and breakdown of passive films, and has been tested by comparing the behaviors of solid and liquid gallium upon anodic polarization in chloride‐containing environments. This study shows that liquid gallium resists passivity breakdown much more readily than does the solid, which we attribute to the inhibition of cation vacancy condensation, in liquid substrate, and hence to the formation of blister precursors at the metal/film interface. Thus, solid gallium is added to the growing list of metals and alloys that apparently suffer passivity breakdown via a vacancy condensate precursor.
2649
M. Maeno, R. Hirayama, H. Izumi, R. Takahashi, K. Chiba, Raymond N. Vrtis and T. Ohmi
2655
K. M. Ogle, C. Gabrielli, M. Keddam and H. Perrot
The quartz crystal microbalance (QCM) was used to monitor the changes in mass which occur when an electrodeposited Zn surface is immersed in a phosphatation solution. The mass‐time profiles obtained can be used to evaluate the activity of the phosphatation solution qualitatively. The shapes of the profiles are interpreted in terms of two interrelated processes, the acid attack of the Zn (leading to a loss of mass) and the precipitation and growth of the phosphate film. Ex situ scanning electron microscopy, x‐ray, and Raman spectroscopy are used to complement the QCM results. The results are consistent with a mechanism involving the nucleation and growth of
islands.
2659
Masahiro Watanabe, Kazunori Tsurumi, Takayuki Mizukami, Toshihide Nakamura and Paul Stonehart
Co‐Pt alloys were studied in detail by a corrosion test under phosphoric acid fuel cell (PAFC) conditions on the well‐defined crystallographic structures for a typical combination of the alloy catalysts used in PAFCs, examining the long‐life stabilities of the structures and the catalytic activities for
electroreduction. The ordered (O) and disordered (D) alloys at the same particle sizes can be obtained by heat‐treating the mother alloy in different temperature sequences. The O‐alloy exhibits a specific activity, an electrocatalytic activity based on the catalyst surface area, 1.35 times higher than the D‐alloy before the corrosion test, but shows less activity (0.73 times) after the corrosion test, due to a higher degradation (47%) in the O‐alloy activity as compared with that of the D‐alloy (1%). It was found that the Co atoms on particle surfaces of both alloys dissolve easily in the acid. This is followed by a second slow dissolution from inside the alloy particles probably due to the protective action by a monolayer thickness of Pt remaining on the alloy surfaces, but the loss of Co in the second stage dissolution for the O‐alloy is higher by several percentage points compared to that of the D‐alloy. It was also found that the Pt content does not change on the catalyst support even after 50 h of corrosion test, but the pure Pt phase is formed in the corrosion product, where the phase for the O‐alloy grows faster than that for the D‐alloy with corrosion time. Based on these results, obtained by chemical, x‐ray diffraction, and transmission electron microscopy with energy dispersive spectroscopy analyses, the corrosion for Pt alloy catalysts is clearly explained, i.e., after the dissolution of Co atoms in the first surface layer of alloys, both Co and Pt dissolve out simultaneously from small‐size alloy particles and the Pt redeposits on the surfaces of large‐size alloy particles (Ostwald ripening). It is concluded that the D‐alloy is preferable to the O‐alloy from the viewpoint of the stabilities in the structure and the electrocatalytic activity, differing from previous claims.
2669
W. P. Yang, D. Costa and P. Marcus
2677
S. T. Zhang, F. P. Kong and R. H. Muller
Ion implantation of different metals in Pb and Pb‐4% Sb has been found to improve the open‐circuit corrosion resistance of the two metals in 5M
. Titanium ions were implanted under different conditions of ion dose and ion energy. Optimum implantation conditions resulted in an up to 72‐fold reduction of corrosion currents. The implantation of V, Cr, Ni, and W has been investigated for one implantation condition and has also resulted in decreased corrosion currents. The corrosion behavior was characterized by the current response to small anodic potential steps. Surface analysis and depth profiles have shown the importance of the spacial distribution of the implanted ions for their effects on the anodic and cathodic parts of the corrosion reactions.
2682
Marie‐Claude Bernard and Anne Hugot‐Le Goff
Polyaniline thin films can serve as material for electrochromic devices, due to the displayed color depth and the rapidity of passage from one color to another. The changes of optical density are particularly interesting in a pH 3 electrolytic medium. In this medium, the films were characterized by Raman and optical (optical multichannel analysis, OMA) spectroscopies and the film stability during different kinds of cycling (for cycles up to 10,000) was investigated; the role of anodic reverse potential was emphasized. The use of a mathematical spectra decomposition allows us to arrive at a semiquantitative Raman analysis, showing the increase of polaron sites during cycling. The analysis of the spectral structure of the polaron optical absorption band, during the polymer equilibration at the coloration potential (obtained owing to OMA) allows us to relate the degradation mechanisms to the organization in bipolarons, followed by their scattering in isolated sites.
2690
W. Da Costa, B. Gleeson and D. J. Young
2698
Xingpu Ye, J. P. Celis, M. De Bonte and J. R. Roos
A study of the relation between electrodeposition process parameters, structure and ductility of electrodeposited zinc foils was carried out. A stretching test was used to determine the ductility of zinc coatings after stripping them from the substrate. Depending on the relative texture coefficient coatings appeared to be more or less ductile. A loss of ductility when the pH of the electrolyte exceeds 4, was identified as due to zinc hydroxide precipitates. These particulates precipitate at the cathode and/or at the anode, then are transferred to the vicinity of the cathode where they can be codeposited with zinc.
2708
Jianren Feng, Dennis C. Johnson, Stephen N. Lowery and James J. Carey
2711
E. Chassaing and B. Sapoval
The response of ideally polarizable electrodes often exhibits a behavior such as
, where
is a constant andη a number smaller than one. Recently an expression for the impedance of two‐dimensional (2‐d) self‐similar electrodes, based on the iteration of a simplified equivalent circuit, has been proposed and experimentally verified. These developments, extended to 3‐d objects, allow us to predict the impedance and quantitatively interpret previous results for ramified electrodes. The impedance response presents two frequency domains. In the low‐frequency range, a behavior similar to that of planar electrodes is observed with a surface equal to the total area of the object. At high frequencies, a fractal constant phase angle behavior is found to be quantitatively compatible with our theoretical prediction.
2716
P. Los, A. Lasia, J. Fournier, L. Brossard and H. Ménard
AC impedance studies of the highly oriented pyrolytic graphite (HOPG) basal plane were carried out in 1M
at 25°C. The data were interpreted in terms of equivalent circuits generally associated with a pure intrinsic semiconductor‐electrolyte interface. A five‐element equivalent‐circuit model was proposed and described satisfactorily the electrochemical properties of the HOPG basal plane at different potentials and frequencies. The space‐charge capacitance, the surface state capacitance parameter, the resistance related to the surface states, the charge‐transfer resistance, and the solution resistance were determined. The influence of hydrogen evolution on the ac impedance response of the HOPG basal plane also was studied. This reaction produces surface defects by increasing the edge‐plane content. The ac technique may be used in the diagnostics of the surface changes.
2722
M. F. Mathias
State‐of‐the‐art ac impedance models of redox‐polymer films attached to an electrode and immersed in a bathing electrolyte usually do not predict the transition region correctly between high frequency Warburg behavior and low frequency capacitive behavior. Two effects are considered here that can give rise to distortions in this spectral region. The first occurs when transport of charge‐compensating counterions in the bathing electrolyte is slow relative to charge transport within the polymer film. The second occurs when the system has a nonuniform primary‐current distribution (e.g., the disk geometry), and the ohmic resistance of the bathing electrolyte is large relative to the transport resistance of the polymer coating. Both these situations are considered using mathematical models. Characteristic parameters are identified which are convenient for diagnosing when the effects are expected to be observed. Analysis of representative data in the literature shows that neither phenomenon is the cause of the majority of the transition‐region nonidealities observed in published ac impedance spectra, although the second effect is important in several studies. The need persists to verify previously postulated causes, such as film‐thickness nonuniformities, or to identify and verify others.
2729
V. Anantharaman and P. N. Pintauro
The kinetics of
evolution and glucose reduction to sorbitol was investigated using a batch slurry reactor containing Raney nickel powder catalyst. In the presence and absence of glucose, hydrogen evolution proceeds via a Volmer‐Heyrovský mechanism, with both steps simultaneously rate controlling at low overpotentials and the Volmer reaction rate limiting at high cathodic overvoltages. A kinetic model for the electrocatalytic hydrogenation of glucose with simultaneous
generation was developed and tested. The model contains rate equations for the individual Volmer, Heyrovský, and glucose hydrogenation steps, a Langmuir adsorption isotherm for glucose, an equation describing the shift in open‐circuit potential due to glucose adsorption on the nickel catalyst, and steady‐state atomic hydrogen and charge balance relationships. The theory accurately predicted potentiostatic polarization data and glucose hydrogenation rates. The results indicate that the mechanism for sorbitol formation with electrogenerated atomic hydrogen on Raney nickel is the same as that for the high temperature and pressure chemical catalytic hydrogenation process.
2742
V. Anantharaman and P. N. Pintauro
2753
Xiaodong Wang, Vijay Modi and Alan C. Westz
Results of numerical simulations of the effect of an oscillating fluid flow on the limiting‐current distribution on a line electrode imbedded in an otherwise insulated plane are presented. The fluid motion is established by a parallel plate oscillating in its own plane. The simulation results agree with theory developed for large Péclet numbers and low oscillation frequencies. It is shown that the average mass‐transfer‐limited current density increases with Péclet number but decreases with dimensionless oscillation frequency. The time‐averaged spatial variation in the normalized distribution is always highly nonuniform, but the temporal variations of the spatially averaged flux decrease significantly with increasing oscillation frequency.
Solid–State Science and Technology
2759
K. Sasaki, H. P. Seifert and L. J. Gauckler
The electrical conductivity of
as well as
solid solutions doped with
,
,
,
, and
is investigated, in the temperature range between room temperature and 1300°C, and in the oxygen partial pressure range between
and 1 atm.
doped with
is an electronic conductor, while
doped with
is an oxygen‐ionic conductor. The two‐phase material of the
solid solutions is a 3‐dimensional composite of ionic and electronic conductors. The single‐phase
doped with
is an electronic conductor with a conductivity up to
in air. Two maxima in electrical conductivity are found, one in the two‐phase region and one in the
single‐phase region. Lattice defects responsible for electronic conduction in pure and doped
are discussed. The defect models for
doped with
are proposed, and the Kröger‐Vink diagram is constructed. The metastable solubility of dopants in
due to the slow phase separation kinetics influences the electronic conductivity.
is a most effective donor for increasing electronic conductivity of
, among hypervalent metal oxides including
,
, and
.
2769
K. Hilpert and M. Millera
The vapor of the
system was investigated under equilibrium conditions between 763 and 1009 K by using Knudsen effusion mass spectrometry with one‐ and two‐compartment Knudsen cells. The gaseous species
,
,
,
,
, and
were detected in the vapor. The enthalpy and entropy changes of the reactions
,
, and
, as well as the enthalpy change of the reaction
, resulted as
,
for reaction Eq. 1;
,
for reaction Eq. 2;
,
for reaction Eq. 3; and
for reaction Eq. 4. The following equilibrium constant was obtained for the dissociation reaction Eq. 1:
. The data are discussed generally as well as with respect to their significance for chemical‐vapor transport in metal halide lamps.
2774
M. Miller, U. Niemann and K. Hilpert
The vapor of the Na‐Sn‐Br‐I system was investigated under equilibrium conditions in the temperature range between 623 and 913 K by the use of Knudsen effusion mass spectrometry with a two‐compartment Knudsen cell. The gaseous species
,
,
,
,
,
,
,
,
,
,
, and
were detected in the vapor. The enthalpy and entropy changes of the reactions
,
, and
resulted as
,
for reaction Eq. 1,
,
for reaction Eq. 2, and
,
for reaction Eq. 3. Gas‐phase equilibria important for the development of metal halide lamps were computed using the results of this work and ancillary data.
2779
H. Näfe and M. Steinbrück
From defect chemical considerations the sodium potential dependencies of the partial electronic conductivities of Na‐β‐alumina are derived. As a result, relationships for the ionic transference number, the open‐circuit voltage of a galvanic cell, the steady‐state ionic current and the sodium potential profile across the electrolyte can be solved for. These relationships serve as a theoretical basis to determine and discuss the role of the partial electronic conductivities under defined operating conditions of the electrolyte.
2784
A. Preuss, B. Adolphi and K. Drescher
The oxidation of In‐48Sn was investigated at partial pressures between 10−8 and 10+4 Pa over the temperature range from 22 to 250°C with different analytical methods. The oxide film contains a mixture of several oxides, although indium oxide forms preferentially. The measurements show at the surface an excess of indium compared to the eutectic composition. Below the melting point, a logarithmic growth, and above this point, a parabolic growth of the oxide film was observed. The oxide film formed in air at 250°C does not exceed about 50 nm in the first 5 min of oxidation.
2789
Jong‐Ho Lee and Han‐Ill Yoo
According to the linear transport theory, the mobile cation flux,
, in an electronic conductor oxide, e.g.,
, is given as
,
being the transport coefficient and
the electrochemical potential gradient of charge carriers of type
. It has, however, been normally presumed that
without experimental verification. By an electrochemical means we have measured the “charge of transport” of the cation,
, in the ranges of temperature and oxygen partial pressure,
and
, respectively, and found, contrary to the normal presumption, that
takes a value in a range of 0.7 to 1.6. Furthermore, it tends to increase with decreasing temperature and increasing oxygen partial pressure. The principle and details of the electrochemical experiment employed are given and the compilation is made of all the data on
of
which have been made available via various means up until now.
2795
Ji‐Guang Zhang, David K. Benson, C. Edwin Tracy, Satyen K. Deb, A. W. Czanderna and R. S. Crandall
Transmissive solid‐state electrochromic devices based on the structure of
were optimized for potential large‐area window applications. The electrochromic layer thicknesses, polymer molecular weights, lithium‐containing electrolytes, preassembly lithium‐ion injection amounts, and transparent conductor substrates were systematically investigated for large optical modulation and fast response of the devices. The transmittance of the optimized device at 633 nm can be switched between 74 and 12% in 1 min. The coloring and bleaching voltages were −1.8 and 1.2 V, respectively.
2801
V. V. Afanas'ev, A. G. Revesz, G. A. Brown and H. L. Hughes
Electrons were injected by UV light into the buried oxide (BOX) layer of pseudo‐separation by implantation of oxygen structures in which the original top Si layer was replaced by a metal electrode. From the photocurrent and metal oxide semiconductor C‐V characteristics, the trapping cross sections, density, and location of the electron traps were determined. Two deep neutral traps with
and
trapping cross sections are responsible for fixed negative charge formation under electron injection. There are also shallow traps present which are responsible for transient effects with a time constant of about 100 s associated with photocurrents. The cross section of the shallow traps is of the order of 10−11 cm2 indicating that the traps are some inclusions (clusters) rather than network defects in the oxide. Both the deep and shallow traps are in the vicinity of the Si‐substrate/BOX interface.
2804
Jung‐Chao Chiou and Mao‐Chieh Chen
2811
S. Deleonibus, F. Martin, B. Blanchard, A. Ermolieff and A. M. Papon
Ultrathin gate oxide (5 to 7 nm) optimization is performed by integration into a SILO/RTN isolation process. The influence of initial conditions on gate oxide defect density and QBD is studied. The gate oxide quality is monitored by the RTN temperature weighed by substrate type and initial oxygen content, epi layer, and the cleaning step before RTN. A new concept of surface monolayer gettering is introduced to explain why a last oxide monolayer before RTN is efficient for contamination trapping on Czochralski grown silicon. A comparison is done between bulk and epi substrate results. In Czochralski material, a maximum oxygen concentration is found to avoid the negative impact of residual oxygen on metal ions trapping during the RTN step. The electrical results are correlated to surface and TEM analysis. The sacrificial oxidation optimization is performed as a function of thickness and temperature with
based oxidation A minimum temperature (950°C) and a minimum thickness (45 nm) are found to minimize defect density and maximize QBD. Standard LOCOS and SILO/RTN isolations are compared. Finally, the possibility of using this isolation on advanced CMOS is demonstrated.
2821
K. Graff and P. Heim
A new preferential etch has been developed which is free of chromium oxide. It is based on various combinations of nitric acid, hydrofluoric acid, and acetic acid. The optimum composition for an etch to reveal haze of all haze‐forming metals (Co, Ni, Cu, Rh, Pd) can be determined from a given equation. With the aid of this equation the proportion of acetic acid is calculated as a function of the preselected proportion of nitric acid to hydrofluoric acid. For the first time haze due to nickel can be distinguished from haze due to copper by etching the sample with solutions of different composition. The new etch is highly sensitive to impurity metals precipitated at the surfaces of silicon samples (haze, shallow etch pits) but it reveals also all other lattice defects (slips, dislocations, epitaxial and oxidation‐induced stacking faults). The etch works independently of the wafer orientation.
2825
Kei Hattori, Masaru Hori and Michishige Aoyama
Residue‐free Al‐Si‐Cu alloy reactive ion etching (RIE) with a high selectivity to photoresist and a slightly positive tapered profile is proposed. An investigation on the mechanism of the formation of residues is presented. The precipitation of Cu and Si is the main reason for residues. The precipitated Cu and Si can be removed by sputtering selectively at a relatively high pressure (8 Pa) and a low temperature (45°C). A new RIE method is proposed for achieving residue‐free, high selectivity to photoresists, and a slightly positive tapered profile by employing magnetron RIE.
2829
Karin Ljungberg, Anders Söderbärg, Anna‐Lisa Tiensuu, Stefan Johansson, Göran Thungström and C. Sture Petersson
A buried conductive layer in silicon has been created using wafer bonding technique, with a cobalt interfacial layer. Co‐coated silicon wafers were brought into contact with either similar or uncoated wafers at room temperature.
was then formed through a solid‐phase reaction, during an anneal at 700 to 900°C. A 700 Å buried
, with a resistivity of approximately 21 μΩ cm, was achieved. Good adhesion, as measured by tensile strength testing, between the wafers was achieved. Transmission electron microscopic investigations (Co‐coated wafer bonded to bare silicon) showed that the silicide has not grown into the opposite wafer, and that an amorphous layer exists between the silicide and the silicon surface. The presence of such a layer has been confirmed by electrical characterization.
2834
Hitoshi Morinaga, Makoto Suyama and Tadahiro Ohmi
2842
J. M. Steigerwald, R. Zirpoli, S. P. Murarka, D. Price and R. J. Gutmann
We describe an investigation into the pattern dependence of dishing and erosion during the chemical‐mechanical polishing of copper used for delineating inlaid metal patterns. Copper dishing is determined to be highly dependent on the width of the copper structure, but only minimally dependent on the density of copper structures. Erosion of the
dielectric layer is strongly affected by the pattern density, but not affected by changes in the width of the copper lines. As a result, both line width and pattern density are important considerations in predicting the final thickness of the copper lines.
2848
A. Tanikawa and T. Tatsumi
Poly‐Si films are grown by ultrahigh vacuum chemical vapor deposition (UHV‐CVD) with plasma‐seeding on
. The preferred grain orientations are investigated as a function of thickness, source gas flow rate, and growth temperature. The poly‐Si films show (100) preferred orientation in a wide range of growth conditions. The (100) orientation increases as thickness and flow rate increases and decreases as temperature increases. UHV‐CVD and other deposition methods are compared in order to estimate the role of hydrogen and oxygen as factors controlling the preferred grain orientation.
2852
S. Verhaverbeke, I. Teerlinck, C. Vinckier, G. Stevens, R. Cartuyvels and M. M. Heyns
2857
Masahiro Akiya and Masatosi Ishii
This paper describes fine‐grained Mg containing Al‐Si alloys, which have an electromigration resistance as much as an order of magnitude higher than that of conventional Al‐Si alloys. Films 1 to 8 μm wide made from those fine‐grained metal systems, with an average grain size under 0.26 μm, have lifetimes that are independent of linewidth.
2860
C. Falcony, M. Garcia, A. Ortiz, O. Miranda, I. Gradilla, G. Soto, L. Cota‐Araiza, M. H. Farias and J. C. Alonso
The room temperature photoluminescence emission characteristics of cerium chloride doped aluminum oxide films deposited by spray pyrolysis are reported. The spectra of the photoluminescence excited with 300 nm light on these samples show a broad emission formed by two overlapping peaks at 365 and 395 nm. The relative emission intensity of these peaks to each other and as a whole is strongly dependent on the doping concentration and the deposition temperature. Energy dispersive x‐ray spectroscopy analysis of the samples as well as the correlations observed with the light emission intensity suggest that the luminescence observed is associated with the molecular incorporation of the
into the aluminum oxide and not to the presence of atomic Ce in the film.
2864
N. Krasteva, V. Fotty and S. Armyanov
The thermal stability of electroless Ni‐X‐P alloys is important for many applications in the electronics industry. This property of amorphous Ni‐P and Ni‐Cu‐P alloys prepared using two different methods (melt‐spinning technique and electroless deposition) is compared by differential scanning calorimetry. Analysis of the crystallization kinetics in both cases is carried out and its parameters are determined. Rapidly quenched alloys show higher thermal stability, while the total heats of crystallization are equal for both preparation methods. It is shown that the introduction of copper into electroless deposited Ni‐P alloys exerts two favorable effects: an increase in crystallization starting temperature and a decrease in magnetization of the ferromagnetic phase precipitated after annealing.
2868
Toshiro Maruyama and Tetsuya Kanagawa
Electrochromic niobium oxide thin films were prepared by chemical vapor deposition. The source material was niobium(V) ethoxide. Amorphous niobium oxide thin films were obtained at a substrate temperature 350°C. Reduction and oxidation of the films in a
buffer solution resulted in desirable changes in optical absorption. Coulometry indicated that the coloration efficiency was 160 cm2 · C−1.
2871
O. Savadogo and K. C. Mandal
A novel method for fabricating high efficiency metal
Schottky barrier solar cells is reported. The method is based on the fabrication of
or
thin films chemically deposited with and without silicotungstic acid (STA). The performances of the Schottky junctions fabricated with the films deposited with STA,
, or
, are significantly higher than those deposited without STA. Under AM1 illumination, the photovoltaic properties of the improved
diode showed
,
,
, and efficiency
. Analogous results are obtained on
, where the photovoltaic response of the improved diode showed
,
,
, and
. The ideality factor
and saturation current density
were also significantly improved. C‐V measurements at 1 MHz showed that the barrier height
of the fabricated diodes are 0.62 and 0.59 eV for
and
junctions, respectively, and 0.81 and 0.80 eV for
and
junctions, respectively. It is also observed that the
values are independent of the metal work functions
. This is attributed to the Fermi level pinning of
or
films deposited with and without STA.
2877
S. ‐S. Sun, R. T. Tuenge, J. Kane and M. Ling
2884
David A. Bell, Carol M. McConica, John L. Falconer and Zhiming Lü
2888
T. J. de Lyon, S. M. Johnson, C. A. Cockrum, O. K. Wu, W. J. Hamilton and G. S. Kamath
2893
Eric A. Robertson III and H. Scott Fogler
2899
M. Miyamoto, N. Kita, S. Ishida and T. Tatsuno
2904
H. Shan, B. K. Srinivasan, D. W. Jillie Jr., J. S. Multani and W. J. Lo
This work addresses effects of deposition and ion scattering on profiles of submicron contacts, vias, and trenches in manufacturing oxide etch, and extends the study to multilevel oxide etch. We observe significant profile modulation by total flow rate, local deposition, and temperature, agreeing with other studies' conclusions for high‐powered single‐wafer etcher. Besides, our experimental results indicate that 3D contact and via profiles are more vertical than 2D trench profiles with the same critical dimension, and smaller features are more vertical than larger ones. With the same aspect ratio, we notice that 2D trenches etch faster than 3D vias. By varying deposition rate, we enable trenches to etch either faster or more slowly than open sites, though vias always have a lower etch rate than open sites. Based on our results, we conclude that submicron oxide etch is solid‐angle dependent.
2910
Sunil Wickramanayaka, Yoshinori Hatanaka, Yoichiro Nakanishi and Alexander M. Wrobel
2915
J. Wu, J. D. Parsons and D. R. Evans
The rate, anisotropy, and morphology obtained by reactive ion etching (RIE) of (111)
epilayer surfaces in
were determined as functions of
ratio and RF incident power density, at 60 mTorr. The
etch rate increased from 100 Å/min at
, to 380 Å/min at
, and then decreased to 0 Å/min
. Anisotropic etching was obtained at all
ratios. As‐etched surfaces were textured (but flat), C‐rich, and contained visible residues adjacent to mesa sidewalls only. The RIE dependence on
ratios and the nearly linear proportional increase of etch rate and
indicates etching occurred by a combination of chemical reactions of (111)
surfaces with F and oxygen radicals and ion bombardment. Titanium carbide (111) surfaces, etched under the same conditions, were isotropically etched, exhibited wavelike morphology, and were free of visible residue.
REVIEW
2918
Ram Gopal and Daniel W. Gibbons