Batteries and Energy Storage
A475
Jiachang Zhao, Yang Dai, Jingli Xu, Sihao Chen and Jingying Xie
A481
Yan-Bing He, Zhi-Yuan Tang, Quan-Sheng Song, Hui Xie, Yuan-Gang Liu and Qiang Xu
A488
Elsa A. Olivetti, Kenneth C. Avery, Ikuo Taniguchi, Donald R. Sadoway and Anne M. Mayes
A494
Keith Promislow, Paul Chang, Herwig Haas and Brian Wetton
A model is presented of a polymer electrolyte fuel cell including slow transient effects of liquid water accumulation and evaporation in gas diffusion electrodes (GDEs) and gas channels. The model is reduced dimensionally, coupling a one-dimensional (1D) model of gas and coolant channel flow to 1D models of transport through the membrane electrode assembly (MEA) and bipolar plates. An asymptotic reduction of the two-phase flow to a sharp interface model is used, in which phase change occurs at a front that evolves in time. The asymptotic reduction is based on an immobile water fraction in the GDE and a large capillary pressure. The water content in the membrane and channels is also tracked in time. Gas and thermal transport are taken to be at quasi-steady state on the time scale of liquid accumulation. The model is fit to Ballard Mk9 cells and validated against experimental measurements of both steady-state and transient MEA water content distributions along the length of the channel. Predictions of slow cyclovoltammograms are presented based on the model.
A505
Masanobu Nakayama, Shinsuke Matsuno, Junichi Shirakawa and Masataka Wakihara
A512
S. Cahen, R. Janot, L. Laffont-Dantras and J. M. Tarascon
A520
Jiangfeng Xiang, Caixian Chang, Feng Zhang and Jutang Sun
A526
Denis Y. W. Yu, Kazunori Donoue, Tetsuo Kadohata, Tetsuyuki Murata, Shigeki Matsuta and Shin Fujitani
A531
C. Portet, G. Yushin and Y. Gogotsi
A537
Y. Takahashi, S. Tode, A. Kinoshita, H. Fujimoto, I. Nakane and S. Fujitani
A542
Xiangchun Zhang, Ann Marie Sastry and Wei Shyy
Intercalation-induced stress and heat generation inside Li-ion battery cathode
particles under potentiodynamic control are simulated in this paper. We combined analyses of transport and kinetics in determining resulting stresses, which arise from concentration gradients in cathode particles, and heat generation. Two peaks in boundary reaction flux, and resulting stresses, were determined from the modeling of electrochemical kinetics and diffusion, using intrinsic material properties (resulting in two plateaus in the open-circuit potential) and the applied potential. Resistive heating was identified as the most important heat generation source. To probe the impact of the particle shape (equivalent radius and aspect ratio of an ellipsoidal particle) and the potential sweep rate on stress and heat generation, a surrogate-based analysis was also conducted. The systematic study showed that both intercalation-induced stress and time-averaged resistive heat generation rate increase with particle radius and potential sweep rate. Intercalation-induced stress increases first, then decreases as the aspect ratio of an ellipsoidal particle increases, whereas time-averaged resistive heat generation rate decreases as aspect ratio increases. This surrogate-based analysis suggests that ellipsoidal particles with larger aspect ratios are preferred over spherical particles, in improving battery performance when stress and heat generation are the only factors considered.
Fuel Cells and Energy Conversion
B645
Kenichi Ide, Makoto Fujimoto, Takashi Kado and Shuzi Hayase
B650
Yau-Pin Chyou, Jong-Sheng Chen and Tsang-Dong Chung
Transient analyses based on electrochemical and thermal models have been performed for investigating the transient behavior of a planar solid oxide fuel cell (SOFC). The reference case illustrated in this work is for an anode-supported fuel cell with an active area of
and thickness dimensions of 700, 25, and
, and
for the anode, electrolyte, cathode, and interconnect, respectively. Typical response time and temperature ramp rate of SOFC under steady operating conditions ascend with increasing current density. Furthermore, a series of step functions of current density were imposed to simulate various start-up operating modes. To avoid the temperature ramp rate being too high during the start-up period, a stepwise increment of current density seems to be most suitable. Finally, an example for optimizing the temperature ramp rate and total response time is illustrated. This example involves a three-step increment series of 300, 500, and
, resulting in a temperature ramp rate that complies with a given specification, e.g., less than
per minute, while the total response time is in the moderate range as well.
B660
F. Bidrawn, S. Lee, J. M. Vohs and R. J. Gorte
The influence of ionic conductivity on the performance of solid oxide fuel cell cathodes was studied for electrodes prepared by infiltration of 
(LCF),
(LSF), and
(LBF) into 65% porous yttria-stabilized zirconia (YSZ). The ionic conductivities of LCF, LSF, and LBF, measured between 923 and
using permeation rates in a membrane reactor, showed that LSF exhibited the highest ionic conductivities, followed by LBF and LCF. When electrodes were calcined to
, the performance characteristics of each composite were essentially identical, exhibiting current-independent impedances of
at
. When the composites were calcined to
, the open-circuit impedances were much larger and showed a strong dependence on current density. The open-circuit impedances followed the ionic conductivities, with LSF–YSZ electrodes showing the lowest impedance and LCF–YSZ electrodes the highest. Scanning electron microscopy images and Brunauer–Emmett–Teller surface areas indicate that calcination at
causes the perovskites to form dense layers over the YSZ pores. A model is proposed in which diffusion of ions through the perovskite film limits the performance of the composite electrodes calcined at
.
B666
Yong Hao and David G. Goodwin
Previous experimental studies have shown that addition of small amounts of oxygen to a hydrocarbon fuel stream can control coking in the anode, while relatively large amounts of oxygen are present in the fuel stream in single-chamber solid oxide fuel cells (SOFCs). In order to rationally design an anode for such use, it is important to understand the coupled catalytic oxidation/reforming chemistry and diffusion within the anode under SOFC operating conditions. In this study, the heterogeneous catalytic reactions in the anode of an anode-supported SOFC running on methane fuel with added oxygen are numerically investigated using a model that accounts for catalytic chemistry, porous media transport, and electrochemistry at the anode/electrolyte interface. Using an experimentally validated heterogeneous reaction mechanism for methane partial oxidation and reforming on nickel, we identify three distinct reaction zones at different depths within the anode: a thin outer layer in which oxygen is nearly fully consumed in oxidizing methane and hydrogen, followed by a reforming region, and then a water–gas shift region deep within the anode. Both single-chamber and dual-chamber SOFC anodes are explored.
B675
V. Sonn, A. Leonide and E. Ivers-Tiffée
A high-resolution impedance study of the hydrogen oxidation in
(yttria-stabilized zirconia) cermet anodes has been realized in consideration of a broad range of operating conditions (temperature and partial pressure of fuel gas components
,
,
, He). A major problem in this respect concerns the origin and physical interpretation of empirical equivalent circuits used to fit the experimental data. We applied a two-stage approach for the evaluation of the impedance data: (i) at first, by the deconvolution of a distribution function of relaxation times (DRT), four different processes and their characteristic relaxation times have been identified. Two processes at frequencies
represent a gas-conversion process or, respectively, a gas diffusion, whereas two processes at higher frequencies
are associated with the electro-oxidation of hydrogen at active sites, including the charge transfer reaction and the ionic transport. (ii) Subsequently, the last mentioned processes were fitted to a “transmission line” model describing the electronic and ionic transport properties of the
cermet. The high resolution of the DRT combined with the numeric accuracy of the complex nonlinear least square (CNLS) fit enabled us to determine (i) the effective ionic conductivity of the
cermet, (ii) the spatial extension of the electrochemically active area adjacent to the electrolyte/electrode interface, and (iii) the charge transfer resistance and its thermal activation energy.
B680
Byung Nam Kim, Dong Hwa Lee and Do Hung Han
B686
A. K. Sahu, G. Selvarani, S. Pitchumani, P. Sridhar, A. K. Shukla, N. Narayanan, A. Banerjee and N. Chandrakumar
B696
Panagiotis Trogadas and Vijay Ramani
B704
Stefan A. Freunberger, Ingo A. Schneider, Pang-Chieh Sui, Alexander Wokaun, Nedjib Djilali and Felix N. Büchi
Cell interaction phenomena in polymer electrolyte fuel cell stacks that arise from imbalance between adjacent cells are investigated in detail experimentally and theoretically. A specialized two-cell stack with advanced localized diagnostics was developed and used to analyze the mechanism and effect of cell-to-cell coupling as a result of operationally relevant variations in reactant feed flow. Contributions to overall and local voltage changes with respect to uniformly operated cells are scrutinized. Unequal operation of the cells causes in-plane current in the bipolar plate to redistribute current and result in inhomogeneous polarization. Both increasing and decreasing polarization along the air-flow path reduces cell power as compared to isopotential operation. A two-dimensional model based on a commercial computational fluid dynamics code is used to back and extend the experimental results to more general cases. Furthermore, the experimental setup presented allowed for the first time to perform simultaneous localized electrochemical impedance spectroscopy beyond the single-cell level. The mechanism of mutual cell interaction on local and integral spectra is revealed. Results show that virtually identical operation of the cells is essential to obtain meaningful integral spectra.
B715
Huayang Zhu and Robert J. Kee
A model is developed to represent chemistry and transport in porous mixed ionic-and-electronic conducting composite electrode structures in solid oxide fuel cells (SOFC). The model considers the coupled behavior of a full membrane electrode assembly (MEA, i.e., cathode, electrolyte, and anode), which is an important advance compared to earlier models that consider only a single electrode structure. Within each electrode the model represents parallel conduction of electrons and ions, as well as porous-media, chemically reacting gas transport. The model predicts electric-potential distributions in both phases. Charge-transfer chemistry is handled via a modified Butler–Volmer formalism, which depends on the local electric-potential difference between phases. Heterogeneous chemistry (e.g., reforming or partial oxidation) is handled via a detailed surface-reaction mechanism. For typical composite-electrode structures the charge-transfer region extends about 10–
from the dense electrolyte. The results show cell performance depends upon particle sizes within the porous electrodes. Smaller particles generally improve cell performance as a result of expanded three-phase-boundary length. However, smaller particle sizes impede gas transport. Cell performance can be optimized as a function of functional-layer thickness and particle sizes. A distributed charge-transfer formulation is especially important in advanced thin-film electrode structures (e.g., segmented-in-series architectures) where the entire MEA is only a few tens of micrometers thick. The model is formulated as continuum differential equations, which are solved computationally on a discrete mesh network. The paper illustrates the model with examples comparing alternative MEA structures.
B730
Christoph Peters, André Weber and Ellen Ivers-Tiffée
Nanoscaled and nanoporous
(LSC) thin film cathodes (film thickness ranging from 200 to
, grain and pore size in the range of
) were electrochemically characterized to determine their potential for intermediate and low-temperature solid oxide fuel cells (SOFCs). Chemically homogeneous, large area
, and nanoporous LSC thin films were derived from metallorganic precursors (metallorganic deposition) and deposited on yttria-doped zirconia [(YSZ) “design 1”] and gadolinia-doped ceria [(GCO) “design 2”]. The area-specific polarization resistance
of both designs was evaluated on symmetrical cells with special emphasis on constancy, depending on temperature
and time by means of electrochemical impedance spectroscopy. For both designs, we report the capability of low polarization resistances, e.g., at
,
(LSC/YSZ), respectively,
(LSC/GCO). Oxygen reduction reaction was facilitated by a substantial inner surface area of the porous thin-film cathode, as suggested by the application of Adler’s model. Nanoporous LSC thin-film cathodes from this study were compared to alternative design concepts for high-performance porous cathodes and with dense
thin-film cathodes. Furthermore, the aim of our study was (i) to find a temperature regime with a perspective for chemical durability of an LSC/YSZ interface. We could prove that at a temperature of
and for
, polarization resistance of the LSC/YSZ interface remains constant, and at unreported low values, which reopens LSC/YSZ for micro-SOFC application; (ii) to estimate the structural durability of nanoscaled and nanoporous LSC thin-film cathodes. We have been able to demonstrate stable and unreported low polarization resistance for LSC/GCO in the temperature range between 500 and
, which is of technical interest for auxiliary-power-unit application.
B738
Hiroyuki Yoshida, Hiroshi Deguchi, Toru Inagaki, Koji Hashino, Mitsunobu Kawano, Kei Hosoi and Masaki Horiuchi
The distribution of residual stress in cells with the practical size of 120 mm diameter was measured by X-ray diffraction utilizing synchrotron radiation at Super Photon ring 8 GeV (SPring-8). The residual stress was determined by the constant penetration depth method. When NiO–samaria-doped ceria (SDC) was sintered on
(LSGMC), the tensile stresses resided in NiO and SDC, and the compressive stress resided in LSGMC. The reduction of the anode by hydrogen decreased tensile stresses in the anode. The residual stresses in the electrodes did not change at any X-ray penetration depth. The sintering of the cathode slightly affected the residual stresses of the cells.
B743
Fangming Jiang and Chao-Yang Wang
Potentiostatic start-up of a proton exchange membrane fuel cell (PEMFC) from subfreezing temperatures is explored in this work. Taking advantage of hydration of membrane and rising cell temperature, potentiostatic start-up features a drastic increase in current density in the course of a cold start, thus leading to substantially more heat generation and a more rapid cell warmup. It is noted that potentiostatic start-up is more advantageous over its galvanostatic counterpart only when the membrane is dry prior to a cold start with sufficient gas purge. In addition, it is found that lowering the cell thermal mass significantly improves the performance of potentiostatic start-up. Minimizing the heat loss from end plates to the ambient is less critical for start-up processes of short duration. Finally, numerical results indicate that it is possible to achieve a self-start from
in
under realistic conditions using the potentiostatic method. While potentiostatic start-up cannot be used directly for fuel cell stacks, it is a fundamental problem representing innovative current-ramping strategies.
B752
X. G. Yang, Y. Tabuchi, F. Kagami and Chao-Yang Wang
Electrochemical and microstructural measurements of membrane electrode assemblies (MEAs) cycled under cold-start conditions are reported. An experimental protocol using a single-cell fixture was developed for MEA durability tests under cold-start cycling. Electrochemical diagnostics using high-frequency resistance and pure
found that MEA no. 1 cycled under
from
does not show any degradation after 100 cycles, MEA no. 2 cycled under
from
exhibits mild degradation after 150 cycles, and MEA no. 3 cycled under
from
suffers severe degradation after 110 cycles. Transmission electron microscopy and X-ray diffraction using cross-sectional samples of the aged MEAs further revealed three primary degradation mechanisms: (i) interfacial delamination between the cathode catalyst layer (CL) and membrane, (ii) cathode CL pore collapse and densification upon melting of a fully ice-filled CL, and (iii) Pt particle coarsening and Pt dissolution in perfluorosulfonic acid ionomer. The interfacial delamination and CL densification appear to be closely related to each other, and the key parameter to affect both is the ice volume fraction in the cathode CL after each cold-start step. Eliminating or minimizing these two degradation processes could improve the MEA cold-start durability by 280%. Mitigation strategies, such as improved gas purge prior to cold start, better MEA design, low startup current density, and low cell thermal mass, are proposed.
B762
Ju-Sik Kim, Su-Il Pyun, Heon-Cheol Shin and Suk-Joong L. Kang
B770
Norimitsu Takeuchi and Thomas F. Fuller
Models of carbon corrosion induced by oxygen and hydrogen coexistence on the negative electrode are presented. In proton exchange membrane fuel cells (PEMFCs), this phenomenon occurs under several situations, such as start-up, shutdown, and hydrogen starvation. In the absence of hydrogen, the source of protons on the negative electrode is the oxygen reduction reaction. The solution potential decreases and induces an overpotential,
, large enough to cause carbon corrosion on the positive electrode even at low temperatures. The carbon corrosion current is large enough to influence the lifetime of PEMFCs not only in the case of high oxygen partial pressure, such as observed during start-up, but also in the case of low partial pressures such as a result of the permeation of oxygen through the membrane. The influence of key parameters for carbon corrosion is investigated. It is clear that the oxygen reduction activity on the negative electrode, the thickness of the membrane, and the cell potential can affect the carbon corrosion on the positive electrode significantly.
B776
Jinhua Yang, Jim Yang Lee, Qingbo Zhang, Weijiang Zhou and Zhaolin Liu
Carbon-supported Pd-rich pseudo-core–shell Pd–Pt (Pd@Pt/C) nanoparticles, with Pt coverage close to a monolayer, were prepared from a simple galvanic replacement reaction between Pd/C particles and
at
. The pseudo-core–shell architecture was confirmed by extensive microstructural characterization techniques. The binding energy shifts in the Pt 4f X-ray photoelectron spectra, in particular, suggest an electron exchange between Pd and Pt, and possible strain effects in Pt caused by the underlying Pd core. The activity of the pseudo-core–shell nanoparticles in the oxygen reduction reaction (ORR) was studied in acidic solutions with and without methanol. The electrocatalysts prepared as such were active for ORR at room temperature, even in the presence of 0.1 M methanol. The pseudo-core–shell
catalyst, in particular, compared rather favorably with a Pt/C catalyst with twice the Pt mass loading in terms of the ORR activity, cost, and methanol tolerance.
Corrosion, Passivation, and Anodic Films
C307
L. D. Liu, S. F. Hsieh, C. Y. Lee and C. S. Lin
The microstructural evolution of the plasma electrolytic anodic coating on AZ31 magnesium alloy in an alkaline silicate solution system was studied. Voltage as high as
was observed in the constant current density anodization and caused a characteristic coating transformation from a single thin porous layer to a multilayered microstructure during the anodization process. This transformation was greatly contributed to physical breakdown behaviors of the thin dielectric, during which, closed and open types of defects were observed. Such defect distribution and density in the barrier dielectric thin film were highly likely to affect the sparking behaviors as well as the resultant coating formed. In a
run of anodization, a near-amorphous, silicate-containing, dense-to-porous overcoat was observed, under transmission electron microscope, attaching to a fluoride-rich barrier layer. In chemical analyses, fluoride contents were concentrated in the barrier layer along the magnesium substrate, while silicate contents were distributed away from the barrier layer in increasing amounts during the growth evolution.
C315
Deepika Sachdeva and R. Balasubramaniam
C324
Mark B. Jensen, Audrey Guerard, Dennis E. Tallman and Gordon P. Bierwagen
Scanning electrochemical microscopy (SECM) has been used to study electron transfer at Al and Al alloy surfaces, employing the mediators hydroquinone, hydroquinone sulfonate, anthraquinone-2,6-disulfonate, and anthraquinone-2-sulfonate. Both oxidation and reduction processes are examined. SECM, in combination with scanning electron microscopy/energy-dispersive X-ray analysis, reveals that Cu-containing secondary phase particles exhibit the highest electron transfer activity for both oxidation and reduction reactions on the AA 2024-T3 surface. Although electron transfer is fastest at the intermetallic particles, it also occurs on the alloy matrix under acidic conditions. The charge carried by the mediator appears to have little influence on the electron transfer process despite the fact that the matrix oxide surface is positively charged below pH 7.
C333
S. J. Garcia-Vergara, M. Curioni, F. Roeth, T. Hashimoto, P. Skeldon, G. E. Thompson and H. Habazaki
An
Au gold alloy is employed to investigate the incorporation of a nonoxidized alloying element into porous anodic alumina films formed in phosphoric acid and sulfuric acid electrolytes. Gold is shown to enrich in the alloy in the initial stages of film growth, when a gold-free film is formed. On sufficient enrichment of the alloy, gold nanoparticles are incorporated into the film above an enriched alloy layer containing nanocrystals of
. The formation of the nanoparticles is accompanied by a reduced rate of film growth due to generation of oxygen. The gold is incorporated into the films preferentially at the cell boundary regions of the scalloped alloy/film interface. Elongated and approximately circular nanoparticles are observed in film sections, the former type being particular to films formed in sulfuric acid electrolyte. The incorporation of gold into the film commences earlier than predicted for a planar alloy/film interface. The behavior suggests that transport of gold occurs within the enriched alloy layer, possibly associated with the stresses at the alloy/film interface due to film growth processes.
C340
Geraint Williams and H. Neil McMurray
C350
K. D. Ralston, S. Chrisanti, T. L. Young and R. G. Buchheit
Nuclear magnetic resonance (NMR) measurements were made on aqueous vanadate solutions to characterize speciation as a function of pH and vanadate concentration. Additionally, potentiodynamic polarization measurements were carried out on Al alloy 2024-T3 in 
solutions in which pH and vanadate concentration were systematically varied. Results showed that inhibition by vanadates occurred mainly in alkaline solutions where tetrahedrally coordinated vanadates, metavanadate and pyrovanadate, were abundant. Inhibition was not observed in solutions where octahedrally coordinated decavanadates predominated. Anodic inhibition, in the form of increased pitting potential, was observed in both aerated and deaerated solutions. In contrast, cathodic inhibition was observed only in aerated solutions acting primarily through the suppression of oxygen reduction. Energy-dispersive spectroscopy, used to collect chemical maps from aluminum coupons exposed to vanadate solutions, showed the suppression of
particle dissolution compared to vanadate-free solutions. NMR measurements were also used to track changes in vanadate speciation with time, pH adjustment, and with exposure to metallic aluminum surfaces. NMR showed noninhibiting octahedrally coordinated decavanadates rapidly decompose into inhibiting tetrahedrally coordinated metavanadates and pyrovanadates after alkaline pH adjustment. While decomposition begins immediately upon pH adjustment, equilibrium may not be reached even after significant time periods.
C360
Z. Y. Chen, F. Cui and R. G. Kelly
Corrosion-resistant materials under atmospheric conditions can suffer from localized corrosion (e.g., pitting, crevice, stress-corrosion cracking). The stability of such a localized corrosion site requires that the site (anode) must dissolve at a sufficiently high rate to maintain the critical chemistry while a wetted surrounding area (cathode) provides matching cathodic current. The objective of this study was to computationally characterize the stability of such a local corrosion site and explore the effects of physiochemical parameters and electrochemical kinetics. The goal is to contribute to the establishment of a scientific basis for the prediction of the stabilization of localized attack. An analytical method for evaluating the stability of localized corrosion of corrosion-resistant alloys under thin-layer (or atmospheric) conditions is presented. The method uses input data that are either thermodynamic in nature or easily obtained experimentally. The maximum cathode current available depends on the cathode geometry, temperature, relative humidity, deposition density of salt (i.e., mass of salt per unit area of cathode), and the interfacial electrochemical kinetics. The anode demand depends on the crevice geometry, the position of attack within the crevice, and the localized corrosion stability product. By coupling these two approaches, the stability of a crevice can be determined for a given environmental scenario. The method has been applied to the atmospheric crevice corrosion of type 316L stainless steel.
C369
R. Hausbrand, M. Stratmann and M. Rohwerder
A key parameter that controls the formation of a local galvanic element during the deadhesion of paint from base metals is the potential gradient between a defect in the paint and the intact metal oxide/polymer interface. The suitable development of zinc coatings allows for control of the potential at the intact interface and thus improvement of the delamination behavior. However, no systematic in-depth study on the origin and meaning of electrode potentials at polymer/metal interfaces or even bare metal surfaces has been presented yet, although in many recent publications Volta potential differences between inclusions and matrix measured on the surfaces of alloys are often interpreted as providing information on the galvanic activity during corrosion. It is the focus of this paper to present a detailed analysis of the origin of the potentials measured on the different materials and to point out what conclusion can be drawn from their values. Special focus is given to the technologically important system
.
Electrochemical/Chemical Deposition and Etching
D493
Da-Wei Liu and Jing-Feng Li
D499
Chang Hwa Lee, John E. Bonevich, Joseph E. Davies and Thomas P. Moffat
Superconformal filling of submicrometer trenches with electrodeposited Ni is demonstrated using a
electrolyte containing 2-mercapto-5-benzimidazolesulfonic acid (MBIS). The process offers the ability to build three-dimensional magnetically active structures that may be easily integrated with other state-of-the-art metallization schemes. MBIS acts to inhibit Ni(Fe) electrodeposition, although under certain conditions rapid, autocatalytic breakdown accompanies the onset of Ni deposition. Optimal trench filling is associated with the positive feedback process, moderated by electrolyte internal-resistance losses, and manifests as a hysteretic voltammetric response on planar electrodes for an MBIS concentration
. On freshly immersed substrates, trench filling is characterized by an initial period of uniform growth followed by the development of a v-notch geometry associated with transient depletion of MBIS within the recessed feature. Interestingly, the finest submicrometer features are filled while only minimal deposition occurs on the neighboring free surface. Continued growth of the MBIS derived v-notch geometry also results in void-free filling of the larger features by geometrical leveling. The same behavior is observed for soft magnetic alloys, such as Ni-rich Ni–Fe alloys. Preliminary experiments indicated that MBIS does not significantly perturb the low coercivity of Ni–Fe alloys, an important attribute for prospective technical applications.
D508
B. B. Burton, A. R. Lavoie and S. M. George
D517
David Avellaneda, M. T. S. Nair and P. K. Nair
Polycrystalline thin films (
in thickness) of
formed from chemical baths of
in acetic acid/
solution, triethanolamine,
(aq), and thioacetamide are polymorphic consisting of zinc blende (ZB) and orthorhombic (OR) structures. The ZB structure for the
film, reported in this work for the first time, has a lattice constant
and a direct (forbidden) bandgap of
, which is distinct from that of
, about
. The electrical conductivity of
is 
p-type, with activation energies for the conductivity of
at room temperature and
near
. When a
film is heated in air at
for
, part of it transforms to
and to
; after 
at
in air the film converts to transparent
. Such a film has a bandgap of
and electrical conductivity, 
. Photovoltaic effect in different structures involving these films is presented.
Electrochemical Synthesis and Engineering
E85
Yuya Kado, Takuya Goto and Rika Hagiwara
E90
Tsuyoshi Murakami and Tetsuya Kato
E96
Agnieszka Kapałka, Barbora Lanova, Helmut Baltruschat, György Fóti and Christos Comninellis
The electrochemical oxidation of acetic acid in 1 M
was studied on boron-doped diamond electrode using differential electrochemical mass spectrometry (DEMS). DEMS was used to identify products and intermediates of the reaction, monitored online during the potential sweep. The measurements showed that the main product of acetic acid oxidation is
, which is formed without showing any evidence for the direct discharge of acetic acid resulting in the Kolbe reaction. In fact, only a small amount of ethane was detected by DEMS. In addition to ethane, methanol was identified as a main intermediate of acetic acid oxidation. Based on these results, a model of indirect oxidation of acetic acid via hydroxyl radicals has been proposed.
E101
Prachi Shrivastava and Michael S. Moats
A coating composition, ruthenium-palladium oxide, for use on titanium anodes for low-current-density oxygen evolution is presented. Coated titanium anodes hold the promise of producing higher-purity deposits with less power consumption in primary metal electrowinning, but their cost and long-term stability have limited their commercial acceptance. A coating based on stabilized
with another precious metal, Pd, has been commercially demonstrated, but limited information regarding its structure, electrochemical activity, and stability has been published. In this study, the structure, properties, and stability of various compositions of
coatings are reported. These coatings exhibit a compact mud-cracked surface. X-ray diffraction indicates the presence of two separate phases,
and
, within the coating. The electrochemical activities of the coatings are similar to
, and the stability of these coatings as determined by accelerated life testing is at least four times better than
.
Physical and Analytical Electrochemistry
F139
H. Yamada, K. Nishikubo and C. N. Xu
Highly europium-doped strontium aluminate phosphor
particles were prepared by microspray pyrolysis. The crystallographic sites of the doped
ions and their local atomic coordinates were determined using a combination of Rietveld refinement and the maximum entropy method (MEM) with high-resolution synchrotron X-ray powder diffraction data. The final Rietveld refinement yielded good
factors of 
and
with the following lattice parameters:
,
,
, and
. It was evident that there were two crystallographic sites for doped
ions, namely, Eu1 and Eu2, which were located far from the Sr sites and had displacements of 0.200(7) and
, respectively. Comparison of the resulting local atomic coordinates of Eu1 and Eu2 revealed similar atomic configurations at both Eu sites, indicating that the emission peaks for both appeared at almost the same positions. Electron density distribution was calculated by MEM, and the results clearly showed that all the doped
ions were introduced near Sr1 and Sr2; no other possible crystallographic sites were found. In addition, a subtle electron density between
and
ions was observed, implying the occurrence of charge transfer between
and
ions.
F145
Jong Hyeok Park, Yongseok Jun, Ho-Gyeong Yun, Seung-Yup Lee and Man Gu Kang
F150
Toshikatsu Kojima, Yoshinori Miyazaki, Katsuhiro Nomura and Kazumi Tanimoto
The density, surface tension, and electrical conductivity of the ternary molten salt mixtures of
system have been measured. The molar volumes of the ternary mixtures agreed well with those estimated by additivity arguments within
. It was found that the surface tension of a ternary carbonate mixture can be predicted from known surface tension of binary carbonates, and the mixing of two molten carbonate mixtures of the same surface tension makes a mixture of almost equal surface tension before mixing in this ternary system. We have succeeded in predicting the equivalent conductivity of the ternary carbonate mixtures using the cationic radii and the equivalent conductivities of the pure carbonates.
F157
Buo-Wei Su, Soundappan Thiagarajan and Shen-Ming Chen
Electrochemical deposition and chemisorption studies of iodide film have been done on the glassy carbon electrode (GCE) and polycrystalline gold electrode (poly GE). The iodide film preparation under different conditions and its stability were examined. Further, the redox activity of the iodide modified film on GCE and poly GE was examined in different pH solutions. Here, the electrochemically deposited iodide film on GCE showed good stability and was electrochemically active at pH 1.5 and 4 solutions, while the chemisorbed iodide film on poly GE was found active and stable at pH 9 and 13 solutions. The iodide modified GCEs exhibits a good electrocatalytic activity for the oxidation of As (III) and the reduction of Cr (VI), respectively. A detailed study for As (III) oxidation has been done by using the rotating ring-disk electrode technique. Meanwhile, chemisorbed iodide film on poly GE shows electrocatalytic reduction reactions of
by using different techniques like cyclic voltammetry and differential pulse voltammetry. To examine the practical analytical utility of the proposed electrode, the real sample analyses for arsenic and chromate detection have been examined and the results were found satisfactory.
F165
Benedetto Bozzini, Lucia D’Urzo, Luca Gregoratti and Abderrahmane Tadjeddine
In this research we observed surface compositional waves developing during galvanostatic electrodeposition of Au–Cu alloys from cyanocomplex solutions. Our study was carried out by synchrotron-based scanning photoemission spectro-microscopy. Scanning electron microscopy and X-ray diffraction analyses complemented the sample characterization. We found that the compositional wavefront developing between two homogeneous regions with different Cu enrichment consists of a progressive localization of Cu, initially at the crystallite boundaries and eventually in the formation of Cu-enriched crystallites.
Dielectric Science and Materials
G141
Hsin-Ying Lee
It is demonstrated that an oxide layer can be formed on the
surface using the photoelectrochemical (PEC) method when the pH value of the electrolyte solution of
is
. To study the effect of thermal treatment on the resulted
oxide films, the as-grown samples were thermally treated at 200, 300, and
in
ambiance for 10, 20, 30, and
. The Auger electron spectroscopy measurement indicated that the resulted layers were composed of O, Ga, and As, and the elements ratio of
of the as-grown layer and the layers annealed at 200, 300, and
in
ambience were 1.39, 1.43, 1.51, and 1.52, respectively, being close to the value for
and
. The X-ray photoelectron spectroscopy analysis showed that the bonding structure in the layer is
or
. These results confirmed that the layer could be identified as
and
, mainly the former. It is also demonstrated that when the oxide layers were thermally treated in
ambiance, the
oxide films became denser, the microstructure of the oxide changed from an amorphous to a polycrystalline structure, and the surface roughness of the oxide layer also changed. It is expected that the oxide
layer grown by the PEC method would replace the externally deposited oxide layers to avoid the influence of surface contaminates and to be used as an insulating layer in various devices.
Semiconductor Devices, Materials, and Processing
H459
Suresh Govindaswamy, Abhinav Tripathi, Ian Ivar Suni and Yuzhuo Li
The introduction of porous low-
dielectric materials into semiconductor devices requires the development of low downforce Cu chemical mechanical planarization (CMP). An alternative passivation agent, 5-phenyl-1H-tetrazole (PTA), is proposed here that is effective at lower pH than the traditional CMP passivation agent, benzotriazole (BTA). PTA has previously been reported as a low-pH Cu corrosion inhibitor, but has not been explored for Cu CMP. Cu CMP removal rates and Cu static etch rates are measured for slurries containing 
,
glycine,
colloidal silica, and PTA concentrations ranging from
. At pH 3 and PTA concentrations of
, PTA provides both effective passivation and Cu removal rates of
. Fourier transform-infrared and electrochemical studies are consistent with the formation of an effective passivation layer on Cu in CMP slurries containing PTA concentrations ranging from
, with the effectiveness of passivation increasing with PTA concentration. The improved low-pH passive film formation for PTA in Cu CMP slurries relative to BTA is most likely due to its much lower pKa (4.3), with a much larger fraction of PTA in the anionic form at low pH.
H464
Hock-Chun Chin, Ming Zhu, Ganesh S. Samudra and Yee-Chia Yeo
H469
Chi-Cheng Hung, Ying-Lang Wang, Wen-Hsi Lee and Shih-Chieh Chang
In order to control the polishing qualities of tungsten (W) and titanium nitride
films in W chemical-mechanical-polishing (WCMP) processes, the electrochemical behavior between the W and the
films deposited at various
flow rates was examined in this study. Metrologies, including X-ray diffractrometry, Auger electron spectrometry, and scanning electron microscopy, were used to verify the physical properties of the
films, while electrochemical analyses, including electrochemical impedance spectroscopy, potential dynamic curves, and potential difference measurements, were used to characterize the mechanism of galvanic corrosion between the W and the
films deposited at various
flow rates. The results show that the N content of the
films influences not only the physical properties of the
films but also the chemical activity in the WCMP slurries. The equivalent circuit, including the charge-transfer resistance and the titanium-oxide resistance associated with tantalum-oxide capacitance, was built to characterize the mechanism of the galvanic corrosion between the W and the
metals.
H474
Matthias Boehringer and Ralf Augke
In noncontact charge-carrier lifetime techniques based on surface photovoltage measurements, uncontrolled surface recombination at the wafer back side may strongly interfere with carrier recombination in the silicon bulk for certain applications. An enhanced surface recombination rate decreases the sensitivity to metallic impurities in the bulk and may furthermore result in misleading data. To circumvent this problem, we use dedicated monitor wafers with a high/low
-junction close to the rear surface, where an electrostatic potential barrier hinders excess minority carriers to recombine at the back side. The benefit of this concept in lifetime measurements employing open-circuit photovoltage decay is demonstrated for the routine supervision of oxidation furnaces and implantation beam lines.
H481
Zilan Li, Tom Schram, Thomas Witters, Hag-Ju Cho, Barry O’Sullivan, Naoki Yamada, Tsunoda Takaaki, Jacob Hooker, Stefan De Gendt and Kristin De Meyer
H485
Yohei Yamada, Nobuhiro Konishi, Junji Noguchi and Tomoko Jimbo
We investigated Cu/low-k integration to test the time-dependent dielectric breakdown (TDDB) reliability of Cu interconnects. We described the relationship between TDDB lifetime and defects possibly caused by the Cu chemical-mechanical polishing (CMP) process, such as rough copper surface corrosion, crevice corrosion, and scratches, using Cu/silicon oxycarbide interconnects. Although rough copper surface corrosion has an insignificant effect on the TDDB lifetime, crevice corrosion at the edges of wires does cause TDDB degradation. We also found that a structure’s TDDB lifetime was affected by the kind of post-CMP cleaning solutions used when barrier metal slurries do not contain benzotriazole (BTA). These results indicate that two types of processes for post-CMP cleaning should be used. It is best to use solutions that do not have strong oxidized copper dissolution ability but can remove particles when a barrier metal slurry with an inhibitor other than BTA is used. Also good are solutions with a strong oxidized copper dissolution ability that have been optimized to prevent Cu corrosion when a barrier metal slurry with BTA is used. To improve TDDB reliability, care must be taken with regard to the combination of the barrier metal slurry and the post-CMP cleaning solution.
H491
Chang-Yeon Kim, Min-Koo Han, Hong-Koo Lee, Sang-Hoon Jung, Chang-Dong Kim and In Byeong Kang
The electrical hysteresis of polysilicon thin-film transistors (poly-Si TFTs) employing a negative data insertion (NDI) has been investigated. It is known that the image sticking in active-matrix organic light emitting diode displays using the poly-Si TFT back plane was mainly caused by the hysteresis of driving TFT in a pixel. In this paper, we propose a type of NDI method using inverse data signals in order to suppress the hysteresis of poly-Si TFTs. Experimental results show that the NDI was very effective to reduce the hysteresis level of poly-Si TFTs induced by carrier trapping and detrapping.
H496
Hoon Kim, Harish B. Bhandari, Sheng Xu and Roy G. Gordon
Cu seed layers for future interconnects must have conformal step coverage, smooth surface morphology, and strong adhesion. Conformal deposition had been achieved by chemical vapor deposition (CVD), but CVD Cu films have rough surfaces and poor adhesion. In this paper, conformal, smooth, adherent, continuous, and thin
Cu films were made by CVD. CuON was deposited from a Cu-amidinate precursor,
, and
at 140–
on Ru. Crystallites in the deposited film have either a
or
structure depending on the ratio of
to
. As-deposited CuON films have a smooth surface morphology [
root-mean-square (rms) roughness] and are highly conformal (
step coverage in 40:1 aspect ratio holes). The CuON films were then reduced with remote hydrogen plasma near room temperature to minimize agglomeration of the thin Cu films during reduction. After reduction, CuON films having a
crystal structure showed a higher density Cu film
than those having a
crystal structure
. Both reduced Cu films had a smooth morphology (
rms roughness). Thus, deposition of a CuON film having a
crystal structure and then reduction with remote hydrogen plasma can make Cu layers that can serve as seed layers of future Cu interconnects.
H504
Hsin-Hsiung Huang, Pei-Lun Wu, Hung-Yu Zeng, Po-Chun Liu, Tung-Wei Chi, Jenq-Dar Tsay and Wei-I Lee
H508
S. H. Yeong, B. Colombeau, C. H. Poon, K. R. C. Mok, A. See, F. Benistant, D. X. M. Tan, K. L. Pey, C. M. Ng, L. Chan et al
Recent research in ultrashallow junction formation has been greatly focused on the development of various advanced annealing techniques. Flash annealing has become one of the most likely candidates to achieve the stringent junction requirements for the forthcoming generation of complementary metal oxide semiconductor devices. In this paper, we present an extensive study on the stability of highly active and ultrashallow
junction in preamorphized silicon formed by optimized flash annealing. Our results demonstrate a strong improvement in junction stability by using the multiple-pulse and pre-spike rapid thermal anneal flash annealing schemes. The deactivation of the flash-annealed junction is clearly shown to be correlated to the different levels of self-interstitial supersaturation, resulting from the release of excess silicon interstitials from the end-of-range defects. We show that optimized multipulse flash annealing could minimize the interaction between point defects and dopant atoms, enabling improvement in junction properties.
H513
Hong-Yeol Kim, Jihyun Kim, Sang Pil Yun, Kye Ryung Kim, Travis J. Anderson, Fan Ren and S. J. Pearton
H516
Seungjun Lee, Seokhwan Bang, Sunyeol Jeon, Semyung Kwon, Wooho Jeong, Seokhoon Kim and Hyeongtag Jeon
Characteristics of hafnium–zirconium–oxide films, with and without remote plasma nitridation, have been investigated. The films were created by atomic layer deposition. After deposition, remote plasma nitridation was performed. Nitrogen atoms were successfully incorporated into the hafnium–zirconium–oxide films. As-deposited hafnium–zirconium–oxide film showed a partially crystallized structure. Remote plasma treatment of the hafnium–zirconium–oxide film can effectively suppress the crystallization of the film during rapid thermal annealing. The annealed hafnium–zirconium–oxide film treated by remote plasma nitridation showed a lower equivalent oxide thickness (EOT) and a lower leakage current density than a non-nitrided sample with the same physical thickness. The EOTs of the mixed oxide films with and without nitridation were approximately 1.8 and 2.0 nm, respectively, and the leakage current densities of the films were
and
, respectively.
H520
Dedy Ng, Tapajyoti Sen, Feng Gao and Hong Liang
This paper investigates friction and wear mechanisms of copper electrochemical mechanical polishing (ECMP) in pH and potential parameters as illustrated in the Pourbaix diagram. Three approaches were used in this study. First, a unique experimental setup was designed to investigate the effects of pH and electropotential on planarization. Second, the friction was measured in situ during polishing and used as a monitoring process. Third, the worn areas correlated with the frictional behavior of post-chemical mechanical polishing samples were characterized to study ECMP removal mechanisms. Results showed that friction maps can be generated in conjunction with the equilibrium Pourbaix diagram. This map is helpful in monitoring the removal rate and wear during copper ECMP. These findings can be used as guidance in ECMP process design and optimization.
H525
Shikao Shi, Jing Gao and Ji Zhou
The red phosphor systems containing
as well as 
, were synthesized through solid-state reactions at high temperature, and their luminescent properties were reported. All of the phosphors were effectively excited by near-UV 395 nm light, and showed superior red emissions around 616 nm to the commercial red phosphor
. Both the emission and excitation intensity were found to increase with increasing Mo content (
value), and reached a maximum when
. In particular, the
phosphor system, in which the charge was efficiently compensated via two
substituting for three
ions, exhibited enhanced red-light emissions as compared with that of the
system. The phosphors are promising candidates as red phosphors under near-UV excitation for solid-state lighting.
H529
Liudmila Larina, Edward M. Trukhan, Oleg Shevaleevskiy and Byung Tae Ahn
H536
Il-Suk Kang, Sung-Hun Yu, Se-Wan Son, Jeonghun Seo and Seung-Ki Joo
Low leakage current structures, such as the lightly doped drain and the field-induced drain, employing a subgate were investigated. In order to achieve the self-alignment of a submicrometer level lightly doped drain, the transmittance change in the phase transformation of silicon by a metal-induced lateral crystallization method was employed. Due to an extended thermionic emission domain, more than one order of magnitude improvements in the leakage current at the practical off-state were obtained. Controlling the subgate dielectric resulted in a better on/off current ratio. Simulated results demonstrated that the proposed field-induced drain structure effectively suppressed the electric fields near the drain.
H540
B. Patsch, A. Ehlert and E. Lankmayr
Epitaxial (epi) stacking faults on silicon wafers were investigated by combining different surface analytical methods. Automatic scanning electron microscope energy-dispersive X-ray spectroscopy analysis provided an overview of the defect situation on the wafer surface (coordinates and composition) before information on the topography by atomic force microscope and data on the stress fields of epi defects by micro-Raman spectroscopy were collected. Sputtering of the defects was carried out by argon or oxygen ions to find the cause of the defect. Delaminated particles were analyzed by Auger electron spectroscopy and time-of-flight secondary ion mass spectrometry. The results demonstrate that the geometrical type of an epi defect depends on the chemical composition and the physical phase of the contamination.
H545
K. Tapily, J. E. Jakes, D. S. Stone, P. Shrestha, D. Gu, H. Baumgart and A. A. Elmustafa
H552
D. P. Brunco, B. De Jaeger, G. Eneman, J. Mitard, G. Hellings, A. Satta, V. Terzieva, L. Souriau, F. E. Leys, G. Pourtois et al
Germanium possesses higher electron and hole mobilities than silicon. There is a big leap, however, between these basic material parameters and implementation for high-performance microelectronics. Here we discuss some of the major issues for Ge metal oxide semiconductor field effect transistors (MOSFETs). Substrate options are overviewed. A dislocation reduction anneal
decreases threading dislocation densities for Ge-on-Si wafers 10-fold to
; however, only a 2 times reduction in junction leakage is observed and no benefit is seen in on-state current. Ge wet etch rates are reported in a variety of acidic, basic, oxidizing, and organic solutions, and modifications of the RCA clean suitable for Ge are discussed. Thin, strained epi-Si is examined as a passivation of the Ge/gate dielectric interface, with an optimized thickness found at
monolayers. Dopant species are overviewed. P and As halos are compared, with better short channel control observed for As. Area leakage currents are presented for p+/n diodes, with the n-doping level varied over the range relevant for pMOS. Germanide options are discussed, with NiGe showing the most promise. A defect mode for NiGe is reported, along with a fix involving two anneal steps. Finally, the benefit of an end-of-process
anneal for device performance is shown.
Sensors and Displays: Principles, Materials, and Processing
J181
Cheng-Wei Liao, Jung-Chuan Chou, Tai-Ping Sun, Shen-Kan Hsiung and Jui-Hsiang Hsieh
J187
Jong-Min Moon and Han-Ki Kim
A facing target sputtering (FTS) system with a configuration of vertically parallel facing Al targets and a substrate holder perpendicular to the Al target plane was designed for direct sputtering of Al cathode on organic layers at a low substrate temperature. The linear FTS system has a linear twin target gun with ladder-type magnet arrays for more effective and uniform confinement of high-density plasma. Due to more effective confinement of high-density plasma and a perpendicularly placed substrate position, we were able to deposit an Al cathode layer directly on an organic layer at a low temperature of
without an additional substrate cooling system. It was found that organic light-emitting diodes (OLEDs) with linear FTS-grown Al cathodes have a lower leakage current density than that of OLEDs with dc-sputtered Al cathodes. The leakage current of OLEDs with linear FTS-grown Al cathodes is similar to reference OLEDs with Al cathodes grown by thermal evaporation. The low leakage current density at reverse and forward bias demonstrates that there is no plasma damage effect caused by the bombardment of energetic particles. This indicates that the FTS system with ladder-type magnet array could be effective in direct Al cathode sputtering on OLEDs or organic photovoltaics.
J193
Yousuke Umetsu, Shinji Okamoto and Hajime Yamamoto
J198
F. Martin Van Assche IV, Juan C. Nino and Eric D. Wachsman
J205
Sonja Laubach, K. C. Mishra, K. Hofmann, B. Albert, P. Larsen, C. Wickleder, R. McSweeney and P. C. Schmidt
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K105
Le Hong Quang and Chua Soo Jin
K110
R. Berenguer, T. Valdés-Solís, A. B. Fuertes, C. Quijada and E. Morallón
Nanostructured cobalt oxide
electrodes were prepared by two different methods. The first one involved the synthesis of
nanoparticles through a nanocasting route using commercial silica gel as a sacrificial template, and in the second one, the
electrodes were prepared by thermal decomposition. The electrodes were characterized by different techniques, such as scanning electron microscopy, energy-dispersive X-ray analysis (EDX), X-ray diffraction (XRD), transmission electron microscopy, X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry. EDX, XRD, and XPS show a characteristic spinel-type structure and a similar chemical composition for the two nanostructured cobalt oxides. However, the surface morphology is different. The electrochemical oxidation of cyanide and phenol in alkaline medium were used as test reactions. The electrocatalytic activity of the nanocrystalline
electrodes for cyanide and phenol oxidation turned out to be highly dependent on the electrode preparation method.
K116
V. Khatko, A. Mozalev, G. Gorokh, D. Solovei, F. Guirado, E. Llobet and X. Correig
K124
George Tsekouras, Attila J. Mozer and Gordon G. Wallace