Batteries and Energy Storage
A65
C. Q. Zhang, J. P. Tu, Y. F. Yuan, X. H. Huang, X. T. Chen and F. Mao
A70
Enrique Ruiz-Trejo, Gustavo Tavizón and Héctor García-Ortega
A75
Ren-Jai Shih, Y. Oliver Su and Tsong P. Perng
The present study is a follow-up of a previous work on hydrogen gas-rechargeable metal hydride (MH) electrode for Ni-MH battery. The hydrogen pressure drop in a
battery during hydrogen absorption and electrochemical discharge was monitored. It was seen that hydrogen was simultaneously absorbed by the MH pellet electrode during discharge at higher pressures, and that the pellet released some hydrogen from the bulk when discharged at lower pressures. Electrochemical impedance spectroscopic analysis showed that the charge transfer step at the MH anode was influenced by the magnitude of hydrogen pressure. The higher hydrogen pressure resulted in a smaller semicircle and therefore a smaller charge transfer impedance.
A80
S. Devaraj and N. Munichandraiah
A89
Francesca Deganello, Vincenzo Esposito, Masaru Miyayama and Enrico Traversa
A97
Wei-Ren Liu, Nae-Lih Wu, Deng-Tswen Shieh, Hung-Chun Wu, Mo-Hua Yang, Christiane Korepp, J. O. Besenhard and Martin Winter
A103
M. N. Obrovac and L. J. Krause
A method is described in which crystalline silicon can be used as a practical anode material for lithium-ion batteries. Commercial lithium-ion cells are typically charged at a constant current to a fixed voltage and then are held by the charger at constant voltage until the current decreases to a certain value (also known as constant current/constant voltage or CCCV charging). It is first shown that CCCV charging can be used to reversibly cycle crystalline silicon and limit its capacity. A cycling method is then demonstrated in which crystalline silicon is first partially converted to amorphous silicon, in situ, during conditioning cycles. After the conditioning cycles the silicon can be cycled normally, using CCCV cycling limits, with good coulombic efficiency and little overlithiation during the first cycle.
A109
Manickam Minakshi, Pritam Singh and David R. G. Mitchell
A114
W. Lu, I. Belharouak, J. Liu and K. Amine
A119
Masao Matsuoka and Kazuaki Tamura
A123
Lingyun Liu, Hansung Kim, Jong-Won Lee and Branko N. Popov
A129
K.-F. Chiu
A134
S. R. Sivakkumar and Dong-Won Kim
A nanocomposite of polyaniline (PANI) and multiwalled carbon nanotube (CNT) was prepared by the in situ chemical polymerization of aniline in well-dispersed CNT solution. The PANI/CNT composite was employed as an active cathode material in rechargeable lithium polymer cells. Gel polymer electrolyte based on the porous poly(vinylidenefluoride-co-hexafluoropropylene) membrane was used as an electrolyte material in assembling the cells. The cell delivered a maximum discharge capacity of
at the 80th cycle with an average coulombic efficiency of 98%. To investigate the effect and role of CNT in the above composite, two different kinds of cathodes were prepared by mechanically mixing the pure polyaniline with CNT or super-p carbon separately. The electrochemical performances of these two cathode materials were also evaluated in the lithium polymer cells.
A140
James Lim, Peter Malati, Francois Bonet and Bruce Dunn
A146
Eiji Hosono, Hirofumi Matsuda, Itaru Honma, Masaki Ichihara and Haoshen Zhou
Tin film as a negative electrode in Li-ion secondary batteries with a flat plateau in the potential vs charge relationship even at a high rate (high current density) were fabricated. The self-nanoporous structure, which means that electrode becomes nanoporous after charge/discharge cycling, due to the lithium insertion/extraction during high-rate charge/discharge, high lithium diffusion coefficients, and metallic conductivity based on tin and tin–lithium alloy, are suitable for the high-rate property. The flat plateau of charge/discharge behavior indicates that this lithium storage device is not a super-capacitor but a secondary battery. This is the first report of a high-rate lithium secondary battery with a flat plateau.
Fuel Cells and Energy Conversion
B123
A. K. Sahu, G. Selvarani, S. Pitchumani, P. Sridhar and A. K. Shukla
B133
D. Waldbillig, A. Wood and D. G. Ivey
The most commonly used solid oxide fuel cell (SOFC) anode material is a two-phase, nickel- and yttria-stabilized zirconia
cermet. During fuel cell operation, this material is exposed to a reducing environment and thus remains a cermet; however, the metallic component of the anode may reoxidize in a commercial SOFC system. Following an initial study of the redox kinetics and dimensional changes after reduction and oxidation, as well as a baseline characterization of the electrochemical performance degradation and microstructural changes after redox cycling, two modifications to the anode microstructure were made in order to enhance cell redox tolerance: the anode functional layer was functionally graded and an oxidation barrier layer was added to the bottom of the cell in order to restrict the ability of oxygen to flow into the anode. Both types of microstructural modification significantly improved the cell redox tolerance compared with standard baseline redox tests.
B139
Leng Mao and Chao-Yang Wang
To enhance cold start capability and survivability of polymer electrolyte fuel cells (PEFCs) at subzero temperatures, a fundamental understanding of the principles involved is required. In this work an analytical model is presented to describe heat balance, ice formation in the catalyst layer, water transport characteristics throughout a fuel cell at very low temperatures, and the ensuing voltage behavior during PEFC cold start. The model is used to elucidate cold start behaviors of a PEFC from
and
and to identify key parameters controlling PEFC cold start, such as the initial membrane water content prior to startup and thermal mass of bipolar plates.
B147
Kazuya Tajiri, Yuichiro Tabuchi and Chao-Yang Wang
Experimental procedures, aimed at elucidating fundamentals of polymer electrolyte fuel cell startup from subzero temperatures, are reported. A method of equilibrium purge using partially humidified gas with well-controlled relative humidity is introduced to effectively control initial water distribution inside a cell prior to cold start. Isothermal cold start, in which single cells with sufficiently large thermal mass are used to fix the cell temperature constant at the startup ambient temperature, is proposed to study intrinsic cold start capability of the membrane-electrode assembly. The proton conductivity of membranes with low water content and at subzero temperatures is measured in situ. The cumulative product water in
has been used to quantify performance of isothermal cold start and is shown to exhibit a nonlinear relationship with the membrane water uptake potential, defined as the difference between the membrane hydration water content and initial value prior to cold start. It is found that the membrane is a key component to enhance the intrinsic capability of isothermal cold start from
. Finally, when the current density is high, the pore volume of the cathode catalyst layer is not fully utilized for ice storage, thereby decreasing cold start performance.
B153
Shigenori Mitsushima, Shuya Kawahara, Ken-ichiro Ota and Nobuyuki Kamiya
The consumption rate of Pt in sulfuric acid under potential cycling has been investigated in 
at
as a basic study to understand the consumption rate of the electrocatalyst of polymer electrolyte fuel cells. With a higher potential limit,
was
vs reversible hydrogen electrode (RHE), the consumption rate was a few
for rectangular and symmetric triangular waves, and the consumption rate increased with the
up to
vs RHE. Among the triangular waves between
vs RHE, the consumption rate of symmetric waves and fast cathodic asymmetric triangular waves were a few
. However, the slow cathodic triangular wave, which were
anodic and
cathodic, showed
consumption rate. The ratio in the difference of charge to the consumption showed that the electron transfer number was about 2 for the slow cathodic triangular wave, and that of the electron transfer number was about 4 for the symmetric waves and the fast cathodic triangular waves. Therefore,
that follows the Pt oxidation,
would occur under the enhanced condition, and
would occur under symmetric conditions.
B159
V. Compañ, F. J. Fernández-Carretero, E. Riande, A. Linares and J. L. Acosta
The preparation of cation-exchange membranes by compression molding of sulfonated EPDM-polypropylene blends is described. Concentration potentials measured in a two-compartmental cell with configuration
solution
membrane∕
solution 
., are a linear function of
(=
, where
and
are, respectively, the concentration and activity coefficient of the solution in compartment 2 keeping constant the concentration in compartment 1,
. The values of the proton transport numbers,
, decrease from 0.99 to 0.94 when the ratio
increases from 0.1 to 5, nearly the same decrease reported for Nafion 117 in the same variation of concentration ratios. Proton conductivities at
are
and
, respectively, for water-saturated membranes containing 20 and 10% of polypropylene, more than one decade below the value reported in the literature for the conductivity of Nafion membranes at the same temperature. These conductivities at
amount to
and
, respectively.
B165
Jaehee Shim, Kwang Yeon Joung, Jae Hwan Ahn and Woong Moo Lee
B170
G. Siné, D. Smida, M. Limat, G. Fóti and Ch. Comninellis
B175
Katsushi Fujii, Masato Ono, Takashi Ito, Yasuhiro Iwaki, Akira Hirako and Kazuhiro Ohkawa
B180
Fei Ye, Toshiyuki Mori, Ding Rong Ou, Motoi Takahashi, Jin Zou and John Drennan
B186
J. St-Pierre, B. Wetton, G.-S. Kim and K. Promislow
Operation of proton exchange membrane fuel cells at high current densities is a potential option to reduce fuel cell cost and volume for automotive applications. This operating regime was investigated using low cell voltages leading to limiting current density values. A zero-dimensional cell voltage model and a one-dimensional low cell voltage model were developed and validated. The operating conditions required for model applicability were summarized. The gas diffusion electrode overall mass transfer coefficient was identified as a key design parameter.
B194
Sang-Yeop Lee, EunAe Cho, Jin-Hwa Lee, Hyung-Juhn Kim, Tae-Hoon Lim, In-Hwan Oh and J. Won
Degradation of polymer electrolyte membrane fuel cells (PEMFCs) that is facilitated by on/off cycles is one of the most important issues for commercialization of fuel cell vehicles. When a PEMFC stack is shut down, residual hydrogen could induce high voltage equivalent to open-circuit voltage to the cathode side that might cause sintering of the Pt catalyst and facilitate the formation of hydrogen peroxide radicals at the anode side that might decompose the Nafion membrane. In this study, the degradation of PEMFCs exposed to repetitive on/off cycles was investigated by measuring current density–voltage characteristics, ac impedance, cyclic voltammograms, gas leak, cross-sectional scanning electron microscopy images, and transmission electron microscopy images. To prevent the degradation of PEMFCs caused by the residual gases, hydrogen was removed from the anode gas channel by air-purging, which was found to be a very effective method.
B201
Shaowu Zha, Zhe Cheng and Meilin Liu
B207
Y. Hao and D. G. Goodwin
A two-dimensional numerical model of a single-chamber solid oxide fuel cell (SCFC) operating on hydrocarbon fuels is developed. The SCFC concept is a simplification of a conventional solid oxide fuel cell in which the anode and cathode are both exposed to the same premixed fuel-air mixture, and selective catalysts promote electrochemical oxidation of the fuel at the anode and simultaneous electrochemical oxygen reduction at the cathode. Optimization of SCFC stacks requires considering complex, coupled chemical and transport processes. The model accounts for the coupled effects of gas channel fluid flow, heat transfer, porous media transport, catalytic reforming-shifting chemistry, electrochemistry, and mixed ionic-electronic conductivity. It solves for the velocity, temperature, and species distributions in the gas, profiles of gaseous species and coverages of surface species within the porous electrodes, and the current density profile in an SCFC stack for a specified electrical bias. The model is general, and can be used to simulate any electrode processes for which kinetics are known or may be estimated. A detailed elementary mechanism is used to describe the reactions over the anode catalyst surface. Different design alternatives including yttria-stabilized zirconia vs
electrolytes, the effects of mixed conductivity, and the optimal fuel-to-air ratio are explored.
B218
Hyunchul Ju, Gang Luo and Chao-Yang Wang
Neutron radiography (NR) was intended to visualize the accumulation and distribution of product water inside diffusion media (DM) in a polymer-electrolyte fuel cell (PEFC). However, the two-dimensional NR technique is unable to separate anode water from cathode water and resolve the liquid water distribution along the cell thickness, two pieces of information strongly needed to characterize the level of cathode DM flooding or anode dry-out. In this paper, NR data analysis is performed for the first time in the context of a three-dimensional two-phase PEFC model. The numerical study illustrates the difficulty in NR data analysis where the major concern originates from the separation of liquid water in the cathode DM from the water in thick membranes, or from liquid water in the anode DM for the thin membrane case. In addition, the two-phase simulation results show that the calculated amount of water according to NR conditions is well within the range measured by NR experiments in the literature, demonstrating the validity of the present two-phase model. A concern is raised whether the two-dimensional NR technique is suitable for studying water management, which generally requires separation of water between the anode and cathode.
B229
Rosa E. Ramírez, Luis C. Torres-González and Eduardo M. Sánchez
Asymmetric aliphatic tetraalkyl phosphonium cations form room-temperature ionic liquids with iodide as an anion. Isobutyl-trihexyl phosphonium iodide shows the highest ionic conductivity at room temperature and it is enhanced by 3-methoxypropionitrile addition. A cyclovoltammetric study shows adequate redox behavior for nanocrystalline solar cells devices.
B234
Tatsuya Iida, Mitsunobu Kawano, Toshiaki Matsui, Ryuji Kikuchi and Koichi Eguchi
Several cermet anode materials were investigated for direct internal reforming operation of solid oxide fuel cells. The effects of steam and discharge conditions were examined for internal reforming operation with propane as a hydrocarbon fuel. Even at high steam-to-carbon (S/C) ratio, power generation characteristics with Ni–yttria-stabilized zirconia (YSZ) were deteriorated during internal reforming operation with propane at
, possibly due to carbon formation at low current densities, whereas stable generation behavior was observed for the cells with Ni–scandia-stabilized zirconia (ScSZ) or Ni–samaria-doped ceria (SDC) anode by feeding propane at low
. The carbon deposition rate was measured for several cermet anode materials by feeding dry or humidified methane by the gravimetric technique. The carbon deposition rate over Ni–ScSZ was lower than Ni–YSZ, leading to better generation performance with propane at low S/C. Ni–SDC showed the highest carbon deposition rate among the cermets investigated, even for humidified methane. This implies that carbon formed over Ni–SDC could be effectively removed upon power generation.
B242
J. R. P. Jayakody, S. H. Chung, L. Durantino, H. Zhang, L. Xiao, B. C. Benicewicz and S. G. Greenbaum
B247
Kazuo Onda, Takuto Araki, Takuya Taniuchi, Daisuke Sunakawa, Kenji Wakahara and Mitsuyuki Nagahama
In order to properly understand the power generation performance of polymer electrolyte fuel cells (PEFCs), it is necessary to have accurate data on water management, such as the diffusion coefficient of water through the membrane electrode assembly (MEA) and gas diffusion layer (GDL), electro-osmotic coefficient through MEA, and power loss data such as the activation and resistance overpotentials. In this study we measured these data with the aim of analyzing our experimental results from PEFC power generation tests done using our two-dimensional simulation code. Our code simultaneously solves mass, charge, and energy conservation equations, and the equivalent electric-circuit for PEFC to obtain numerical distributions of hydrogen/oxygen concentrations, cell potential, current density, and gas/cell-component temperatures. The current density distributions calculated with our simulation code were compared with the distribution measured using a segmented electrode cell. The distributions measured under various operating conditions agreed well with the calculated ones, demonstrating that our code is reliable. The concentration overpotential through GDL was also estimated with the parallel fine-pore model, but the estimated concentration overpotential was very small. Also, the cathode flooding is discussed with the calculated distribution of saturation degree along the channel flow, in comparison with experimental stability.
B258
Takafumi Akamatsu and Toshihiro Kasuga
B263
Rune Halseid, Jesse S. Wainright, Robert F. Savinell and Reidar Tunold
B271
Hui Xu, H. Russell Kunz, Leonard J. Bonville and James M. Fenton
The effects of lower equivalent weight (EW) perfluorosulfonic acid (PFSA) ionomers and
catalyst on the cathode performance of proton exchange membrane fuel cells (PEMFCs) were investigated at two atmospheric pressure operating conditions: low temperature/high relative humidity (RH),
RH, and high temperature/low RH,
RH. Cell voltage at a current density of
was used for the performance comparison. The optimized content in the electrode changed with the ionomer EW, from 32% for 1100 EW Nafion, 28% for 920 EW Nafion to 25% for a developmental PFSA 800 EW ionomer. Compared to 1100 EW Nafion, 800 EW ionomer significantly improved the cell performance by 39 mV at
RH; however, at
RH, its effect was not apparent. The introduction of
catalyst into the cathode increased the cell performance by
at
RH, which was much higher than a performance improvement at
RH. Compared to electrodes made of
and Nafion 1100 EW, the combination of 800 EW Ionomer and
catalyst resulted in a
cell voltage increase at
RH and a
cell voltage increase at
RH.
B279
K. C. Neyerlin, Wenbin Gu, Jacob Jorne, Alfred Clark Jr. and Hubert A. Gasteiger
B288
Elena Chalkova, Mark V. Fedkin, Sridhar Komarneni and Serguei N. Lvov
Nafion/zirconium phosphate (ZP) composite membranes of different structures containing in situ precipitated ZP, crystalline layer-structured α-zirconium hydrogen phosphate 
, and three-dimensional-network zirconium hydrogen phosphate 
were synthesized. The ZP materials used have different structure and surface properties (specific surface area, zeta potential, and particle morphology). The composite membranes were studied in an
proton exchange membrane fuel cell (PEMFC) over a range of relative humidity (RH) from 13 to 50% at temperatures of 80 and
. At the operating temperature of
, all studied composite membranes demonstrated significant improvement in performance under dehydrating conditions compared to unmodified Nafion membranes. Among the tested membranes, the Nafion/α-ZPL composite membrane demonstrated the highest performance at
at all RH values, especially at 13% RH. At 26 and 50% RH, the performance of Nafion/α-ZPL and Nafion/19% ZP in situ membranes were close, and the performance of the Nafion/ZPTD membrane was the lowest. The effects of filled polymer pore constriction, scaffold formation, membrane structure, and surface properties of the ZP particles on the membrane performance in PEMFCs are discussed in the paper.
Corrosion, Passivation, and Anodic Films
C67
Subrahmanya Shreepathi, Hung Van Hoang and Rudolf Holze
Corrosion protection performance of a completely soluble polyaniline-dodecylbenzenesulfonic acid salt (PANI-DBSA) on C45 steel has been studied with electrochemical impedance and potentiodynamic measurements. Chloroform is the most suitable solvent to process the pristine PANI-DBSA because of negligible interaction of the solvent with the polyaniline (PANI) backbone. An anodic shift in the corrosion potential
, a decrease in the corrosion current, and a significant increase in the charge-transfer resistance indicate a significant anti-corrosion performance of the soluble PANI deposited on the protected steel surface. Corrosion protection follows the mechanism of formation of a passive oxide layer on the surface of C45 steel. In situ UV-vis spectroscopy was used to investigate the differences in permeability of aqueous anions into PANI-DBSA. Preliminary results of electron diffraction studies show that PANI-DBSA possesses an orthorhombic type of crystal structure. An increase in the feed ratio of DBSA to aniline increases the tendency of aggregation of spherical particles of PANI obvious in transmission electron microscopy. PANI-DBSA slowly loses its electrochemical activity in acid free electrolyte without undergoing degradation.
C74
K. Darowicki, J. Orlikowski, A. Arutunow and W. Jurczak
In this paper the passive layer cracking process that occurs under tensile stresses and anodic polarization conditions on AA1050, AA5052, AA5056, and AA7005 aluminum alloys was examined by means of direct current (dc) technique, dynamic electrochemical impedance spectroscopy (DEIS), and acoustic emission (AE). Research revealed the advantage of DEIS and AE methods over the dc one. It was also possible to determine the exact moment of the passive layer cracking on investigated aluminum alloys.
C81
Vicky Mei-Wen Huang, Vincent Vivier, Mark E. Orazem, Nadine Pébère and Bernard Tribollet
Two numerical methods were used to calculate the influence of geometry-induced current and potential distributions on the impedance response of an ideally polarized disk electrode. A coherent notation is proposed for local and global impedance which accounts for global, local, local interfacial, and both global and local ohmic impedances. The local and ohmic impedances are shown to provide insight into the frequency dispersion associated with the geometry of disk electrodes. The high-frequency global impedance response has the appearance of a constant-phase element (CPE) but can be considered to be only an apparent CPE because the CPE exponent α is a function of frequency.
C89
Vicky Mei-Wen Huang, Vincent Vivier, Isabelle Frateur, Mark E. Orazem and Bernard Tribollet
Numerical methods were used to calculate the influence of geometry-induced current and potential distributions on the impedance response of a blocking disk electrode with a local constant-phase element behavior. While the calculated global impedance is purely capacitive, the local impedance has high-frequency inductive loops that were observed in experiments conducted on a stainless steel electrode in
electrolyte. The calculated global impedance responses are in good agreement with experimental results obtained using both the steel electrode and a glassy-carbon disk in
electrolytes of differing concentrations. The computed local and both local and global ohmic impedances are shown to provide insight into the frequency dispersion associated with the geometry of disk electrodes.
C99
Vicky Mei-Wen Huang, Vincent Vivier, Mark E. Orazem, Nadine Pébère and Bernard Tribollet
Geometry-induced current and potential distributions modify the global impedance response of a disk electrode subject to faradaic reactions. The problem was treated for both linear and Tafel kinetic regimes. The apparent capacity of a disk electrode embedded in an insulating plane was shown to vary considerably with frequency. At frequencies above the characteristic frequency for the faradaic reaction, the global impedance response has a quasi-constant-phase element (CPE) character, but with a CPE coefficient α that is a function of both dimensionless frequency K and dimensionless current density J. For small values of J, α approached unity, whereas, for larger values of J, α reached values near 0.78. The calculated values of α are typical of those obtained in impedance measurements on disk electrodes. For determining the interfacial capacitance, the influence of current and potential distributions on the impedance response cannot be neglected, even if the apparent CPE exponent α has values close to unity. Several methods taken from the literature were tested to determine their suitability for extracting interfacial capacitance values from impedance data on disk electrodes. The best results were obtained using a formula which accounted for both ohmic and charge-transfer resistances.
C108
Geneviève Baril, Gonzalo Galicia, Claude Deslouis, Nadine Pébère, Bernard Tribollet and Vincent Vivier
The corrosion behavior of pure magnesium in sodium sulfate solutions was investigated using voltammetry and electrochemical impedance spectroscopy with a rotating disk electrode. The analysis of impedance data obtained at the corrosion potential was consistent with the hypothesis that Mg corrosion is controlled by the presence of a very thin oxide film, probably MgO, and that the dissolution occurs at film-free spots only. This hypothesis was substantiated both by the superposition of the EIS diagrams, obtained for different immersion times and for two
concentrations once normalized, and by use of scanning electrochemical microscopy in the ac mode to sense the local conductivity of the material. On the basis of the electrochemical results, a model was proposed to describe magnesium corrosion at the open-circuit potential. Simulation of the impedance diagrams was in good agreement with the experimental results.
C114
S. Hodges, N. J. Laycock, D. P. Krouse, S. Virtanen, P. Schmutz and M. P. Ryan
C120
J. Sandberg, I. Odnevall Wallinder, C. Leygraf and N. Le Bozec
C132
T. Makino, R. S. Alwitt and S. Ono
C138
Mirjana Metikoš-Huković, Ranko Babić, Željka Petrović and Damir Posavec
Self-assembled monolayers (SAMs) formed by the adsorption of alkanethiols onto copper is a simple method for producing coatings that can protect the metal against oxidation and corrosion. However, a contradiction regarding the influence of oxygen on the SAMs formation and barrier properties is still present. In this work the SAMs of dodecanethiol (DT) were formed on the copper substrates from ethanolic solutions of DT with and without the presence of dissolved oxygen. The protecting properties of monolayers were studied in a sodium acetate solution with a pH of 6 using cyclic voltammetry and electrochemical impedance spectroscopy. The effect of exposing samples, prepared in the deoxygenated solutions, to air was also studied to examine the decrease in the protecting properties of the SAMs against copper corrosion. The protection efficiency of the DT SAMs was compared with those of benzotriazole, which is known as the best inhibitor for copper corrosion.
C144
Guo Gao and Chenghao Liang
Some β-amino alcohols compounds in the series of 1,3-bis-dialkyl
aminopropan-2-ols referred to as
-apo-
, where
, 3 and 4, were tested as volatile corrosion inhibitors for brass in simulated atmospheric water using potentiodynamic, potentiostatic current transient, electrochemical impedance spectroscopy, gravimetric, and volatile inhibition ability measurements. The evolution of the inhibition effect of the investigated compounds has been monitored according to the length of alkyl chain. The results indicated that the inhibition efficiency increased with increasing the alkyl chain length and inhibitor concentration. Polarization curves showed that these compounds acted as good anodic inhibitor in simulated atmospheric water. The values of charge transfer resistance, obtained from impedance plots of brass, distinctly increased with increase of the inhibitor concentration. The inhibition mechanism was discussed in light of the chemical structure of undertaken inhibitors. The adsorption of the inhibitors on the brass surface followed Langmuir adsorption isotherm model. The surface evaluation techniques like scanning electron microscopy and Fourier transform infrared spectroscopy were used to characterize the surface film.
Electrochemical/Chemical Deposition and Etching
D65
Yaowu Hao, F. Q. Zhu, C. L. Chien and Peter C. Searson
Here we report on the fabrication of ordered macroporous nickel structures by electrodeposition into colloidal crystal templates formed by self-assembly of polystyrene particles with diameters from
to
. The current during deposition into well-ordered colloidal crystals with low defect density exhibits periodic oscillations associated with the change in fractional area within the crystal. Magnetic hysteresis loops and magnetoresistance measurements are performed as a function of pore diameter and film thickness. The magnetic properties can be explained by modeling the ordered macroporous nickel structures as a three-dimensional network structure with magnetic particles connected by narrow ligaments.
D70
Jaesung Lee and Jan B. Talbot
A model of particle electrocodeposition on a rotating cylinder electrode was developed to predict the incorporated particle volume fraction in a composite film. Asymptotic solutions to the transport equations for ions within the diffusion boundary layer showed that diffusion of the reactive species in a supporting electrolyte solution is the dominant process to carry current at the cathodic surface. The ratio of the total volume of particles to that of the deposited metal was expressed as a function of two transport parameters, current density, a probability to determine the particle surface concentration, and two experimental fitting parameters.
D78
Min Tan, Clint Guymon, Dean R. Wheeler and John N. Harb
This paper documents an experimental study to compare the behavior of bis-(3-sodiumsulfopropyl) disulfide (SPS)–Cl–polyethylene glycol (PEG) and 3-mercaptopropanesulfonic acid sodium salt (MPSA)-Cl-PEG additive systems during copper electrodeposition. These systems are analogous to those used industrially to plate copper lines onto integrated circuits. Galvanostatic experiments show that in the absence of chloride ion, either SPS or MPSA added to the plating solution inhibited copper deposition. Upon the addition of
, a rapid transition from inhibition to acceleration was observed for both additives, illustrating the critical role played by the chloride ion in these systems. Potentiostatic experiments performed for the Cl–PEG–SPS and Cl–PEG–MPSA additive systems show that the potential dependency of the Cl–PEG–SPS system was much stronger than that of the MPSA–Cl–PEG system. Differences between the SPS and MPSA additive systems suggest that acceleration may occur through an MPSA pathway. Finally, results with chemical compounds similar to MPSA indicate that the thiol group is associated with inhibition and that a synergistic accelerating relationship exists between the sulfonate group and chloride, presumably due to complex formation.
D82
Naoki Ohashi, Kenji Takahashi, Shunichi Hishita, Isao Sakaguchi, Hiroshi Funakubo and Hajime Haneda
D88
R. C. Da Silva and W. Schwarzacher
D91
Longcheng Wang, Kunee Han and Meng Tao
D95
Seong Keun Kim, Sang Young Lee, Sang Woon Lee, Gyu Weon Hwang, Cheol Seong Hwang, Jin Wook Lee and Jaehack Jeong
Electrochemical Synthesis and Engineering
E25
Dane T. Cestarolli and Adalgisa R. de Andrade
E31
Samuel Shikuku Libendi, Takashi Ogino, Osamu Onomura and Yoshihiro Matsumura
Physical and Analytical Electrochemistry
F25
Luis J. Núnez-Vergara, R. Salazar, P. A. Navarrette-Encina, C. Camargo, C. Yanez and J. A. Squella
A study of the electrolytic oxidation of three new C-4 nitrofuryl 1,4-dihydropyridines in nonaqueous aprotic medium is presented. Controlled-potential electrolysis (CPE) in dimethylformamide
tetrabutyl-ammonium hexafluorophosphate
was followed by UV-visible spectroscopy, high-performance liquid chromatography (HPLC)-photodiode array (PDA), and gas chromatography-Mössbauer spectroscopy (GC-MS) chromatography, and electron spin resonance and electrochemical techniques. Carbon-centered radical intermediates produced in the electrochemical oxidation of C-4 nitrofuryl substituted 1,4-dihydropyridines were trapped with N-benzylidene-tert-butylamine-N-oxide (PBN) and their splitting constants were calculated. The neutral pyridine derivatives were identified by GC-MS techniques as final oxidation products. HPLC-PDA and GC-MS chromatographic techniques were used to follow the time-course of CPE of both parent 1,4-DHP derivatives and their respective oxidation products. Also, an overall oxidation mechanism of C-4 nitrofuryl-1,4-DHP derivatives is presented.
F31
Shunichi Uchiyama, Hiroaki Watanabe, Haruhito Yamazaki, Aiko Kanazawa, Hiroshi Hamana and Yoshio Okabe
F36
Yu Cai, Alfred B. Anderson, John C. Angus and Lubomir N. Kostadinov
F44
Roger T. Bonnecaze, Nicolas Mano, Bomi Nam and Adam Heller
The behavior of the current from a porous rotating disk electrode (PRDE) as a function of the rotation rate, electrode geometry, and porosity at large overpotentials is studied experimentally. The current shows a much richer behavior than the flat RDE, including a sigmoidal dependence on the rotation rate. At low rotation rates, the measured current is qualitatively similar to that of an RDE, with the current increasing with the square of the rotation rate. However, at a critical rotation rate, which we term the lower critical rotation rate and which depends on the radius, the thickness, and the porosity of the porous disk, the current increases much more rapidly than predicted by the Levich theory. At a larger, upper critical rotation rate, the current increases more slowly and then approaches a plateau. The plateau value greatly exceeds that predicted by Levich and is about 20 times greater than that for a flat electrode. The results are explained in terms of the angular velocity dependence of the ratio of the effective electrochemical reaction time to the residence time of the fluid in the porous disk. A theory is presented that collapses the data onto a universal curve.
F48
Shinya Higashimoto, Takeru Shishido, Yoshiki Ohno, Masashi Azuma, Masanari Takahashi and Masakazu Anpo
Dielectric Science and Materials
G25
Wenwu Wang, Toshihide Nabatame and Yukihiro Shimogaki
Hafnium carbonitride
films were synthesized as a metal-gate electrode by metallorganic chemical vapor deposition using 
precursor. The physical and electrical properties, especially the dielectric evolution characteristic of oxide dielectric, were evaluated using X-ray photoelectron spectroscopy, capacitance–voltage, and current–voltage measurements. As a result, the capacitance-deduced equivalent oxide thickness (EOT) becomes much smaller than the initial physical thickness of various oxide dielectrics after
deposition. For the case of
stacks, the reduction in EOTs was attributed to the increase in average effective dielectric constant, possibly due to atoms interdiffusion, e.g., N, Hf, or O atoms, which may promote the formation of high-κ dielectric phases. Based on the dielectric evolution characteristic, although the leakage current in the
stack with reduced EOT is close to the level of the doped-polysilicon/
stack, Hf-based metal electrode/high-κ dielectric/Si MOS stacks are also expected to be integrated into thermal oxide/Si stacks by one-step metal electrode deposition, which results in conversion of the
layer into a high-κ dielectric layer.
G30
N. A. Chowdhury and D. Misra
G38
L. Young and A. Kulpa
We have investigated certain aspects of the dielectric properties of anodic oxide films on tantalum in connection with Dignam’s theory that a special current-driven polarization process is responsible for the transients shown by the ionic current on changing the electric field in the oxide. In his experiments, which were claimed to prove this theory, films were first held at potentials giving fields too low to produce significant ionic current. When voltage pulses were applied large enough to produce fields giving ionic current, extra current was observed to flow for a short time. This was taken as due to the decay of the dielectric polarization built up due to the ionic current, and partial numerical agreement with the model was found. In the present experiments the discharge current flowing after longer periods of voltage application or of ionic current flow was investigated with the aim of finding if more polarization was indeed produced by ionic current flow. The current was not found to be larger after discharge from fields giving ionic current, as required by Dignam’s model. It is argued that structural changes in the glassy oxide are responsible for the transients.
G44
Martin M. Frank, Yu Wang, Ming-Tsung Ho, Rhett T. Brewer, Naim Moumen and Yves J. Chabal
Semiconductor Devices, Materials, and Processing
H67
M. Devika, N. Koteeswara Reddy, K. Ramesh, R. Ganesan, K. R. Gunasekhar, E. S.R. Gopal and K. T.Ramakrishna Reddy
SnS films with different thicknesses have been deposited on glass substrates at a constant substrate temperature of
. The physical properties of the films were investigated using energy dispersive analysis of X-rays, X-ray diffraction, scanning electron microscopy, atomic force microscopy, van der Pauw method, and Fourier transform infrared spectroscopy measurements at room temperature. The deposited films exhibit only SnS phase with different orientations. We show that the electrical resistivity, activation energy, and optical bandgap of the films depend strongly on the preferred orientation of the SnS films. The electrical resistivity of films decreased with the increase of film thickness. The optical and electrical data of the SnS film are well interpreted with the composition, crystal, and surface structure data.
H74
Y. H. Jeong, J. B. Lim, S. Nahm, H.-J. Sun and H. J. Lee
H78
C. O’Dwyer, D. N. Buckley, D. Sutton, M. Serantoni and S. B. Newcomb
H86
M. Yoshida, U. Gösele, M. Morooka and S. Tanaka
In silicon, I and V coexist, where I and V represent self-interstitials and vacancies, respectively. The Frenkel pair reaction of I and V is assumed to be in the near-equilibrium state. Under this condition, I and V diffuse interactively. Interactive diffusion equations of I and V are solved under the condition of an oxidizing atmosphere. From the solutions of concentrations of I and V thus obtained, the effective diffusion coefficients of I and V are obtained by the Boltzmann–Matano method. These results show that I and V diffuse separately with different effective diffusion coefficients like the single diffusions at and near the surface and that I and V diffuse with the same effective diffusion coefficient in the bulk where the concentrations of I and V are their equilibrium values.
H91
Haizheng Song, Masakazu Sugiyama, Yoshiaki Nakano and Yukihiro Shimogaki
H97
Seokhoon Kim, Sanghyun Woo, Hyungseok Hong, Hyungchul Kim, Hyeongtag Jeon and Choelhwyi Bae
H102
Chang Su Kim, Sung Jin Jo, Sung Won Lee, Woo Jin Kim, Hong Koo Baik and Se Jong Lee
H105
Tzu-Juei Wang, Hung-Wei Chen, Ping-Chun Yeh, Chih-Hsin Ko, Shoou-Jinn Chang, John Yeh, San-Lein Wu, Chwan-Ying Lee, Wen-Chin Lee and Denny D. Tang
H109
Jian Zhang, Shoutian Li and Phillip W. Carter
The surface reactivity of tantalum metal and its associated oxide in aqueous environments was explored using electrochemical impedance spectroscopy (EIS) and potentiodynamic electrochemical dc tests in combination with tantalum blanket wafer removal rates produced by chemical mechanical polishing. The EIS data indicated that the transient tantalum oxide films formed during polishing are thinner and have a lower charge-transfer resistance at pH 2 compared to pH 10. The thinner film at pH 2 is attributed to easier mechanical removal of the tantalum oxide at low pH compared to high pH. Polishing experiments showed tantalum blanket wafer removal rates 6 to 20 times greater at pH 2 compared to pH 10 for three different oxidizing agents. In addition, there was a measurable induction time before material removal via polishing at pH 10 where pH 2 showed no significant induction time. The mechanical removal of the surface oxide, not charge-transfer, is postulated to be the rate limiting step in tantalum polishing conditions utilizing low downforces, low abrasive concentrations, and a soft pad within the pH range 2–10. The ease of mechanical removal at low pH may result from enhanced interactions of tantalum surface functionalities with abrasive or solution species.
H115
A. Y. Polyakov, N. B. Smirnov, B. P. Gila, M. Hlad, A. P. Gerger, C. R. Abernathy and S. J. Pearton
H119
C. H. Liu, K. T. Lam, S. J. Chang, C. K. Wang and Y. S. Sun
H124
Hongguo Zhang, Zhi Chen, Tianxiang Li, Fengjuan Wang and Kozo Saito
A one-dimensional array of carbon nanotubes horizontally aligned on silicon substrates was successfully grown using a flame synthesis method based on the template of a one-dimensional anodic aluminum oxide nanopore array. The diameter and length of nanotubes are controlled by the geometry of nanopores of the aluminum oxide template. This one-dimensional carbon nanotube array may have great potential for fabrication of nanoelectronic devices and nanoelectromechanic systems (NEMS) compatible with the planar processing technology.
H127
F. M. Mohammedy, Z. L. Peng, D. A. Thompson and M. J. Deen
Sensors and Displays: Principles, Materials, and Processing
J59
Hongchuan Zhang, Takashi Horikawa, Hiromasa Hanzawa, Ayanori Hamaguchi and Ken-ichi Machida
J62
Zhiya Zhang and Yuhua Wang
J65
Masaru Nagai
J71
C. L. Yu, C. H. Chen, S. J. Chang and P. C. Chang
Interdisciplinary Topics
P1
Benjamin Y. Park, Rabih Zaouk, Chunlei Wang and Marc J. Madou
Fractal electrode designs are proposed for electrochemical devices. A zeroth-order approximation fractal model is analyzed and basic insights into the scaling laws of the electrical properties and the surface-to-area ratio are derived. Fractal electrodes can minimize internal resistance while maximizing surface-to-volume ratios. Recent carbon microelectromechanical systems (C-MEMS) techniques show great promise for use in the fabrication of fractal electrodes for electrochemical applications. Preliminary results showing carbon fractal electrodes fabricated using C-MEMS techniques are presented.
P6
Sung Jong Yoo, Ju Wan Lim, Baeck Choi and Yung-Eun Sung
P11
Keng-Liang Ou, Chang-Chih Chen, Che-Tong Lin, Chin-Sung Chen, Chia-Cheng Lin and Sheng-Yang Lee
P16
Y. S. Lin, Y. H. Tseng, R. S. Liu and Jerry C.C. Chan
P20
Andrew T. Stamps, Shriram Santhanagopalan and Edward P. Gatzke
Curve fitting is commonly used to determine a mathematical expression for sets of experimental data. While there are many instances when theory dictates a linear, quadratic, or other simple mathematical form for a relationship, there are often times when the theoretical form is either unknown or too unwieldy to be used effectively. A common example is the open-circuit-potential relationship of a Li-ion battery. One may use empirical correlations such as high-order polynomials (HOP) or various types of splines which are piecewise polynomials of low order. Despite their simplicity, HOPs are often undesirable given their numerical instability as well as their poor extrapolation performance. Certain splines generally produce acceptably smooth curves but use an unacceptably large number of fitting parameters. A method is presented for construction of continuous and smooth piecewise polynomials. Using significantly fewer polynomial segments than experimental data points, the number of parameters required to develop the calibration curves of a Li-ion battery is substantially reduced from that of splines while maintaining a similar level of fit quality. Mixed-integer programming techniques are employed to ensure that the knot (transition point) placement is optimal.