Table of contents

Preface

The organizing committee of FMSP 2017 is proud to present the proceedings of the 1st International Conference on Frontiers of Materials Synthesis and Processing (FMSP 2017: http://www.icfmsp.org/), held from 28 to 29 October 2017, in Changsha, China.

FMSP 2017 aims at creating a meeting point for researchers and practitioners that from both China and abroad to exchange ideas in the domain of Materials Synthesis and Processing and related topics with its prospective application in the various interdisciplinary domains of engineering, including not only technological issues but also social issues.

FMSP 2017 received 791 manuscripts, and 168 submissions have been accepted by our reviewers. Articles submitted to the conference should report original, previously unpublished research results, experimental or theoretical and must not be under consideration for publication elsewhere. We firmly believe that ethical conduct is the most essential virtual of any academic. Hence any act of plagiarism is a totally unacceptable academic misconduct and cannot be tolerated. The committees of FMSP 2017 invested great efforts in reviewing the papers submitted to the conference and organizing the sessions to enable the participants to gain maximum benefit.

Hopefully, all participants and other interested readers will benefit scientifically from the proceedings and also find it stimulating in the process.

With our warmest regards,

Lin Liu

Conference Organizing Chair

Wuhan, China

List of Conference Chairmen, Scientific Committee, Organizing Committee are available in this pdf.

All papers published in this volume of IOP Conference Series: Materials Science and Engineering have been peer reviewed through processes administered by the proceedings Editors. Reviews were conducted by expert referees to the professional and scientific standards expected of a proceedings journal published by IOP Publishing.

Taking into many influencing factors, a Needle Roller Bearings life calculation model was established using the Influence coefficient method and ISO formula. Take this model as the optimization objective function, some optimization variables were determined, and these variables were added constraint conditions. Using dynamic nonlinear strategy to improve the inertia weight, the arccosine strategy to adjust the learning factor, function constraints was solved by the methods of ensure particle legitimacy. Nonlinear optimization design of cylindrical roller bearings was realized by Improved Particle Swarm Algorithm. The proposed method of bearing design was verified effective by test of the optimization results.

Costs of maintenance and loss of power generation caused by the faults of wind turbines gearboxes are the main components of operation costs for a wind farm. Therefore, the technology of condition monitoring and fault recognition for wind turbines gearboxes is becoming a hot topic. A condition monitoring and fault recognition system (CMFRS) is presented for CBM of wind turbines gearboxes in this paper. The vibration signals from acceleration sensors at different locations of gearbox and the data from supervisory control and data acquisition (SCADA) system are collected to CMFRS. Then the feature extraction and optimization algorithm is applied to these operational data. Furthermore, to recognize the fault of gearboxes, the GSO-LSSVR algorithm is proposed, combining the least squares support vector regression machine (LSSVR) with the Glowworm Swarm Optimization (GSO) algorithm. Finally, the results show that the fault recognition system used in this paper has a high rate for identifying three states of wind turbines' gears; besides, the combination of date features can affect the identifying rate and the selection optimization algorithm presented in this paper can get a pretty good date feature subset for the fault recognition.

Joint clearances and friction characteristics significantly influence the mechanism vibration characteristics; for example: as for joint clearances, the shaft and bearing of its clearance joint collide to bring about the dynamic normal contact force and tangential coulomb friction force while the mechanism works; thus, the whole system may vibrate; moreover, the mechanism is under contact-impact with impact force constraint from free movement under action of the above dynamic forces; in addition, the mechanism topology structure also changes. The constraint relationship between joints may be established by a repeated complex nonlinear dynamic process (idle stroke - contact-impact - elastic compression - rebound – impact relief - idle stroke movement - contact-impact). Analysis of vibration characteristics of joint parts is still a challenging open task by far. The dynamic equations for any mechanism with clearance is often a set of strong coupling, high-dimensional and complex time-varying nonlinear differential equations which are solved very difficultly. Moreover, complicated chaotic motions very sensitive to initial values in impact and vibration due to clearance let high-precision simulation and prediction of their dynamic behaviors be more difficult; on the other hand, their subsequent wearing necessarily leads to some certain fluctuation of structure clearance parameters, which acts as one primary factor for vibration of the mechanical system. A dynamic model was established to the device for opening the deepwater robot cabin door with joint clearance by utilizing the finite element method and analysis was carried out to its vibration characteristics in this study. Moreover, its response model was carried out by utilizing the DOE method and then the robust optimization design was performed to sizes of the joint clearance and the friction coefficient change range so that the optimization design results may be regarded as reference data for selecting bearings and controlling manufacturing process parameters for the opening mechanism. Several optimization objectives such as x/y/z accelerations for various measuring points and dynamic reaction forces of mounting brackets, and a few constraints including manufacturing process were taken into account in the optimization models, which were solved by utilizing the multi-objective genetic algorithm (NSGA-II). The vibration characteristics of the optimized opening mechanism are superior to those of the original design. In addition, the numerical forecast results are in good agreement with the test results of the prototype.

In recent years, with the gradual extension of reliability research, the study of production system reliability has become the hot topic in various industries. Man-machine-environment system is a complex system composed of human factors, machinery equipment and environment. The reliability of individual factor must be analyzed in order to gradually transit to the research of three-factor reliability. Meanwhile, the dynamic relationship among man-machine-environment should be considered to establish an effective blurry evaluation mechanism to truly and effectively analyze the reliability of such systems. In this paper, based on the system engineering, fuzzy theory, reliability theory, human error, environmental impact and machinery equipment failure theory, the reliabilities of human factor, machinery equipment and environment of some chemical production system were studied by the method of fuzzy evaluation. At last, the reliability of man-machine-environment system was calculated to obtain the weighted result, which indicated that the reliability value of this chemical production system was 86.29. Through the given evaluation domain it can be seen that the reliability of man-machine-environment integrated system is in a good status, and the effective measures for further improvement were proposed according to the fuzzy calculation results.

The solid model of orbiting and fixed scroll is created by the Solidworks The deformation and stress of scrolls under gas force, temperature field, inertia force and the coupling field are analyzed using the Ansys software. The deformation for different thickness and height scroll tooth is investigated. The laws of deformation and stress for scrolls are gotten. The research results indicate that the stress and deformation of orbiting scroll are mainly affected by the temperature field. The maximum deformation occurs in the tooth head of scroll wrap because of the largest gas forces and the highest temperature in the tooth head of scroll wrap. The maximum stress is located in the end of the tooth, and the maximum stress of the coupling field is not the sum of loads. The scroll tooth is higher, and the deformation is bigger. The scroll tooth is thicker, and the deformation is smaller.

In this paper, the crankshaft automatic adjustment mechanism designed on CYJY10-4.2-53HF pumping unit is used as the research object. The simulation of the friction and bending moment of the crank is carried out by ANSYS Workbench, and the finite element simulation results are compared with the theoretical calculation results to verify the theoretical calculation. The final result is that the finite element analysis of the friction of the crank is basically consistent with the theoretical calculation; The analysis and calculation of the stress and deformation about the two kinds of ultimate conditions of the guide platform are carried out too; The dynamic state analysis of the mechanism is carried out to obtain the vibration modes and natural frequencies of the vibration of the different parts of the counterweight under the condition of no preload force so that the frequency of the array can avoid the natural frequency, and can effectively avoid the resonance phenomenon, and for different modes we can improve the stiffness of the structure.

To investigate the effect of pre-strain on behaviors in a specially developed Al-4.5Zn-1.2Mg alloy, transmission electron microscopy (TEM) bright field (BF) imaging combined with select area electron diffraction (SAED), Vickers-hardness tests and electrical conductivity tests was conducted for insight into precipitation in aluminum (Al) matrix during two step ageing, and standard exfoliation corrosion (EXCO) test combined with high-angle angular dark field scanning transmission electron microscopy (HAADF-STEM) and scanning electron microscopy (SEM) was carried out for corrosion behavior. Results showed that pre-strain accelerated precipitation during two step ageing as the sequence of: (i) supersaturated solid solution (SSS), GPI zones precipitations, GPI dissolution; (ii) SSS, fcc precipitates, η' phases or η phases. And the precipitation hardening of the fcc precipitates was not effective as GPI zones. Pre-strain also accelerated EXCO developing, which was mainly attributed to the coverage ratio of η phases on high-angle grain boundaries (HAGBs) increasing as pre-strain increase.

Deepwater robots are important devices for human to explore the sea, which is being under development towards intellectualization, multitasking, long-endurance and large depth along with the development of science and technology. As far as a deep-water robot is concerned, its mechanical systems is an important subsystem because not only it influences the instrument measuring precision and shorten the service life of cabin devices but also its overlarge vibration and noise lead to disadvantageous effects to marine life within the operational area. Therefore, vibration characteristics shall be key factor for the deep-water robot system design. The sample collection and recycling system of some certain deepwater robot in a mechanism for opening the underwater cabin door for external operation and recycling test equipment is focused in this study. For improving vibration characteristics of locations of the cabin door during opening processes, a vibration model was established to the opening system; and the structural optimization design was carried out to its important structures by utilizing the multi-objective shape optimization and topology optimization method based on analysis of the system vibration. Analysis of characteristics of exciting forces causing vibration was first carried out, which include characteristics of dynamic loads within the hinge clearances and due to friction effects and the fluid dynamic exciting forces during processes of opening the cabin door. Moreover, vibration acceleration responses for a few important locations of the devices for opening the cabin cover were deduced by utilizing the modal synthesis method so that its rigidity and modal frequency may be one primary factor influencing the system vibration performances based on analysis of weighted acceleration responses. Thus, optimization design was carried out to the cabin cover by utilizing the multi-objective topology optimization method to perform reduction of weighted accelerations of key structure locations.

In this paper, a new type of Delta robot with only two degrees of freedom is proposed on the basis of multi - degree - of - freedom delta robot. In order to meet our application requirements, we have carried out structural design and analysis of the robot. Through SolidWorks modeling, combined with 3D printing technology to determine the final robot structure. In order to achieve the precise control of the robot, the kinematics analysis of the robot was carried out. The SimMechanics toolbox of MATLAB is used to establish the mechanism model, and the kinematics mathematical model is used to simulate the robot motion control in Matlab environment. Finally, according to the design mechanism, the working space of the robot is drawn by the graphic method, which lays the foundation for the motion control of the subsequent robot.

Five species of landscape plants which are scindapsus aureus, water hyacinth, cockscomb, calendula officinalis and salvia splendens were used as experimental materials to study their removal effects on nitrogen, phosphorus, chemical oxygen demand (COD_Mn) and suspended solids (SS) in urban river water. The results show that the 5 landscape plants have good adaptability and vitality in water body, among them, water hyacinth had the best life signs than the other 4 plants, and its plant height and root length increased significantly. They have certain removal effects on the nitrogen, phosphorus, COD_Mn (Chemical Oxygen Demand) and SS (Suspended Substance) in the landscape water of Dalong Lake, Xuzhou. Scindapsus aureus, water hyacinth, cockscomb, calendula officinalis and salvia splendens on the removal rate of total nitrogen were 76.69%, 78.57%, 71.42%, 69.64%, 67.86%; the ammonia nitrogen removal rate were 71.06%, 74.28%, 67.85%, 63.02%, 59.81%;the total phosphorus removal rate were 78.70%, 81.48%, 73.15%, 72.22%, 68.52%;the orthophosphate removal rates were 78.37%, 80.77%, 75.96%, 75.96%, 71.15%;the removal rate of COD_Mn was 52.5%, 55.35%, 46.02%, 45.42%, 44.19%; the removal rate of SS was 81.4%, 86%, 79.1%, 76.7%, 74.42%.The purification effect of 5 kinds of landscape plants of Dalong Lake in Xuzhou City: water hyacinth> scindapsus aureus>cockscomb>calendula officinalis>salvia splendens.

The three-dimensional model of high-speed loading spindle is established by using ABAQUS's modeling module. A finite element analysis model of high-speed loading spindle was established by using spring element to simulate bearing boundary condition. The static and dynamic performance of the spindle structure with different specifications of the rectangular spline and the different diameter neck of axle are studied in depth, and the influence of different spindle span on the static and dynamic performance of the high-speed loading spindle is studied. Finally, the optimal structure of the high-speed loading spindle is obtained. The results provide a theoretical basis for improving the overall performance of the test-bed

Computational Fluid Dynamics (CFD) is an analysis of the physical phenomena involved in fluid flow and heat conduction by computer numerical calculation and graphical display. The numerical method simulates the complexity of the physical problem and the precision of the numerical solution, which is directly related to the hardware speed of the computer and the hardware such as memory. With the continuous improvement of computer performance and CFD technology, it has been widely applied to the field of water conservancy engineering, environmental engineering and industrial engineering. This paper summarizes the development process of CFD, the theoretical basis, the governing equations of fluid mechanics, and introduces the various methods of numerical calculation and the related development of CFD technology. Finally, CFD technology in the mechanical engineering related applications are summarized. It is hoped that this review will help researchers in the field of mechanical engineering.

In this work, kaolin powder and glass fiber fabric were added to PF in order to improve its thermal stability and mechanical property. Micro-structures of carbonized PF with kaolin powder were inspected by scanning electron microscopy (SEM) to demonstrate the filler's pinning effect. SEM results illustrated modified PF had well morphology after high-temperature heat treatment. The Fourier transform infrared spectrometer (FTIR) test was carried out and found that kaolin powder only physically dispersed in PF. The compression test and thermal weight loss test were done on two groups of modified PF (Group A: add powder and fabric; Group B: add powder only). Results showed that all modified PF were better than pure PF, while foams with powder and fabric showed better mechanical characteristic and thermal stability compared with foams with powder only.

In this paper, taking the designer of the new compound balance pumping unit beam as our research target, the three-dimensional model is established by Solid Works, the load and the constraint are determined. ANSYS Workbench is used to analyze the tail and the whole of the beam, the stress and deformation are obtained to meet the strength requirements. The finite element simulation and theoretical calculation of the moment of the center axis beam are carried out. The finite element simulation results are compared with the calculated results of the theoretical mechanics model to verify the correctness of the theoretical calculation. Finally, the finite element analysis is consistent with the theoretical calculation results. The theoretical calculation results are preferable, and the bending moment value provides the theoretical reference for the follow-up optimization and research design.

With the continuous development of the scale of the cultivation of the radix pseudostellariae, the traditional separation mode cannot adapt to the mass production of the crown prince, and the existing manual separation mode is of great labor intensity and low degree of mechanization. Therefore, it is necessary to design a disengaging mechanism of radix pseudostellariae and soil on the basis of the design principle of modern agricultural machinery. According to the physical characteristics and growing environment of radix pseudostellariae, a drum-type separating component is presented, and the drum screen separating mechanism and vibration mechanism of the disengaging mechanism are designed. In this paper, the movement rule and time of the mixture of radix pseudostellariae and soil are determined in the drum screen. Rotation speed of the drum screen is calculated, and the operation rules of the eccentric wheel in the vibration mechanism are summarized.

In order to study the three-phase brushless motor control system of electric vehicle, Freescale9S12XS128 chip is used as the control core, and the power MOSFET is used as the inverter device. The software is compiled by Codewarrior software. The speed control link adopts open-loop control, and the control chip collects the external sensor signal voltage Change control PWM signal output control three-phase brushless DC motor speed. The whole system consists of Hall position detection module, current detection module, power drive module and voltage detection module. The basic functions of three-phase brushless DC motor drive control are realized.

In this study, four different types of adsorbents modified from corn stalk were synthesized after the reaction with epichlorohydrin, N,N-dimethylformamide, triethylamine and different cross-linking agents. The surface functional groups and thermal stability of modified corn stalk (MCSs) were characterized using FTIR and TG analysis, respectively. The feasibility of using MCSs to remove Cr(VI) were evaluated. Adsorption isotherms were determined and modeled with Langmuir, Freundlich and Temkin equations. The experimental results showed that MCS modified using diethylenetriamine (DETA) had the best modification effect, and the adsorption capacity of Cr(VI) reached as high as 227.27 mg/g at 323 K. Thermodynamic study showed that the Cr(VI) adsorption onto MCSs was endothermic processes. As a result, MCS by using DETA as cross-linking agent has good potential for the removal of Cr(VI) from aqueous solutions.

Registration of simultaneous polarization images is the premise of subsequent image fusion operations. However, in the process of shooting all-weather, the polarized camera exposure time need to be kept unchanged, sometimes polarization images under low illumination conditions due to too dark result in SURF algorithm can not extract feature points, thus unable to complete the registration, therefore this paper proposes an improved SURF algorithm. Firstly, the luminance operator is used to improve overall brightness of low illumination image, and then create integral image, using Hession matrix to extract the points of interest to get the main direction of characteristic points, calculate Haar wavelet response in X and Y directions to get the SURF descriptor information, then use the RANSAC function to make precise matching, the function can eliminate wrong matching points and improve accuracy rate. And finally resume the brightness of the polarized image after registration, the effect of the polarized image is not affected. Results show that the improved SURF algorithm can be applied well under low illumination conditions.

For parts with many features, there are more empty tracks during machining. If these tracks are not optimized, the machining efficiency will be seriously affected. In this paper, the characteristics of the empty tracks are studied in detail. Combining with the existing optimization algorithm, a new tracks optimization method based on Z-Map model is proposed. In this method, the tool tracks are divided into the unit processing section, and then the Z-Map model simulation technique is used to analyze the order constraint between the unit segments. The empty stroke optimization problem is transformed into the TSP with sequential constraints, and then through the genetic algorithm solves the established TSP problem. This kind of optimization method can not only optimize the simple structural parts, but also optimize the complex structural parts, so as to effectively plan the empty tracks and greatly improve the processing efficiency.

The soil pH of Fufeng County, Yangling County and Wugong County in Shaanxi Province was studied. The spectral reflectance was measured by ASD Field Spec HR portable terrain spectrum, and its spectral characteristics were analyzed. The first deviation of the original spectral reflectance of the soil, the second deviation, the logarithm of the reciprocal logarithm, the first order differential of the reciprocal logarithm and the second order differential of the reciprocal logarithm were used to establish the soil pH Spectral prediction model. The results showed that the correlation between the reflectance spectra after SNV pre-treatment and the soil pH was significantly improved. The optimal prediction model of soil pH established by partial least squares method was a prediction model based on the first order differential of the reciprocal logarithm of spectral reflectance. The principal component factor was 10, the decision coefficient Rc2 = 0.9959, the model root means square error RMSEC = 0.0076, the correction deviation SEC = 0.0077; the verification decision coefficient Rv2 = 0.9893, the predicted root mean square error RMSEP = 0.0157, The deviation of SEP = 0.0160, the model was stable, the fitting ability and the prediction ability were high, and the soil pH can be measured quickly.

Mechanical properties of filament winding composites are usually tested by NOL ring samples. Few people have studied the size effect of winding composite samples on the testing result of mechanical property. In this research, winding composite thickness, diameter, and geometry of NOL ring samples were prepared to investigate the size effect on the mechanical strength of carbon fiber (CF) winding composite. The CF T700, T1000, M40, and M50 were adopted for the winding composite, while the matrix was epoxy resin. Test results show that the tensile strength and ILSS of composites decreases monotonically with an increase of thickness from 1 mm to 4 mm. The mechanical strength of composite samples increases monotonically with the increase in diameter from 100 mm to 189 mm. The mechanical strength of composite samples with two flat sides are higher than those of cyclic annular samples.

This study aims to explore changes of long-term fertilization on spore density and colonization of AMF (Arbuscular mycorrhizal fungi) under a 38-y long-term fertilization in a brown soil. Soil samples (0-20 cm,20-40cm,40-60cm)were taken from the six treatments of the long-term fertilization trial in October 2016:no fertilizer (CK), N₁(mineral nitrogen fertilizer), N₁P (mineral nitrogen and phosphate fertilizer), N₁PK (mineral nitrogen, phosphate and potassic fertilizer), pig manure (M₂), M₂N₁P (pig manure, mineral nitrogen andphosphate fertilizer).Spores were isolated from soils by wet sieving and sucrose density gradient centrifugation; mycorrhizal colonization levels were determined by the gridline intersect. The spore density was highest in the topsoils (0-20 cm), and was decreased with increasing of soil depth in each treatment. The spores density of M₂N₁P treatment was significantly higher than that of other treatments in each soil layer. Application of inorganic fertilizer (especially inorganic with organic fertilizer) can greatly improve the level of colonization. Our results suggested that long-term fertilization significantly affects spore density and colonization of AMF, however, spore density is not related to colonization rate.

Nowadays, flexible electronic devices are increasingly used in direct contact with human skin to monitor the real-time health of human body. Based on the Fourier heat conduction equation and Pennes bio-heat transfer equation, this paper deduces the analytical solutions of one - dimensional heat transfer for flexible electronic devices integrated with human skin under the condition of a constant power. The influence of contact thermal resistance between devices and skin is considered as well. The corresponding finite element model is established to verify the correctness of analytical solutions. The results show that the finite element analysis agrees well with the analytical solution. With bigger thermal resistance, temperature increase of skin surface will decrease. This result can provide guidance for the design of flexible electronic devices to reduce the negative impact that exceeding temperature leave on human skin.

A phytochemical study was performed on Arundina graminifolia (D.Don) Hochr. by silica gel column and semi-preparative HPLC, and ten stilbenoids were obtained. Their structures were elucidated by NMR and MS spectra and identified as 7-hydroxy-2,4-dimethoxy-9,10-dihydrophenanthrene (1), 4,7-dihydroxy-2-methoxy-9,10-dihydrophenanthrene (2), 2,7-dihydroxy-4-methoxy-9,10-dihydrophenanthrene (3), 3,3'-dihydroxy-5-methoxy-bibenzyl (4), 7-hydroxy-2,8-dimethoxy-phenanthrene-1,4-dione (5), 7-hydroxy-2,10-dimethoxy-phenanthre-ne-1,4-dione (6), 7-dihydroxy-2-methoxy-9,10-dihydrophenanthrene-1,4-dione (7), 7-hydroxy-2-methoxy-phenanthrene-1,4-dione (8), 7-hydroxy-1-(p-hydroxybenzyl)-2,4-dimethoxy-9,10-dihydroxy-phenanthrene (9), 2,7-dihydroxy-1-(p-hydroxybenzyl)-4-methoxy-9,10-dihydroxy-phenanthrene (10). Compounds 5 and 6 were isolated from this plant for the first time. The isolated compounds were examined for their anti-hepatic fibrosis activity against HSC-T6 cells in vitro. The results showed that compounds 4 and 5 exhibited moderate growth inhibitory effects with IC50 61.9 μg/mL and 52.7 μg/mL, respectively.

Colloidal particles can influence the foamability and stabilization of aqueous foam by addition of surfactant at the air-water interface. This occurs because particles are activated via the interaction with surfactant and are adsorbed onto the surfaces of foams. This phenomenon has been applied extensively to the development of new materials and techniques. Whether particle surface can be activated or not is decided by the interaction between the surfactant and the particle. In this work, we studied the effects of cationic surfactant CTAB (cetyltrimethylammonium bromide) on PS (polystyrene), SiO₂, and TiO₂ particles in aqueous solution, and compared the difference in their surface activation according to foam volume of the particles/CTAB/water system, and the degrees of foamability and foam stabilization. In addition, the influence of anionic surfactant SDS (sodium dodecyl sulfate) on the surface activation of PS in aqueous solution was also analyzed and compared with that of CTAB.

In the light of the azeotrope of ethyl acetate-ethanol-water, a process of pressure-swing distillation is proposed. The separation process is simulated by Aspen Plus, and the effects of theoretical stage number, reflux ratio and feed stage about the pressure-swing distillation are optimized. Some better process parameters are as follows: for ethyl acetate refining tower, the pressure is 500.0 kPa, theoretical stage number is 16, reflux ratio is 0.6, feed stage is 5; for crude ethanol tower, the pressure is 101.3 kPa, theoretical stage number is 15, reflux ratio is 0.3, feed stage is 4; for ethanol tower, the pressure is 101.3 kPa, theoretical stage number is 25, reflux ratio is 1.2, feed stage is 10. The mass fraction of ethyl acetate in the bottom of the ethyl acetate refining tower reaches 0.9990, the mass fraction of ethanol in the top of the ethanol tower tower reaches 0.9017, the mass fraction of water in the bottom of the ethanol tower tower reaches 0.9622, and there is also no ethyl acetate in the bottom of the ethanol tower. With laboratory tests, experimental results are in good agreement with the simulation results, which indicates that the separation of ethyl acetate ethanol water can be realized by the pressure-swing distillation separation process. Moreover, it has certain practical significance to industrial practice.

Micro-motion feature is one of the effective features used for radar target recognition in the middle section of the ballistic curve. The micro-Doppler expressions of the scattering center at the conical point and two sliding scattering centers in the conical bottom are given, firstly. Then by analyzing the micro-Doppler expressions, it is found that only the precession frequency can be estimated from the micro-Doppler expressions, and other parameters can't be estimated directly. But all precession and geometry parameters can be estimated by decreasing the number of parameters in the micro-Doppler expressions of two sliding scattering centers, which must use two groups of echoes illuminating the same warhead target from the cone top and the cone bottom. Finally, a new method of estimating all precession and geometry parameters is proposed, and it is validated by the simulation analysis.

The soil condition and condition of the plow affect the tillage resistance and the maximum traction of tractor. In order to improve the adaptability of tractor tillage depth control, a multi-parameter control strategy is proposed that included tillage depth target, draft force aim and draft–position mixed ratio. In the strategy, the resistance coefficient was used to adjust the draft force target. Then, based on a JINMA1204 tractor, the electro-hydraulic hitch prototype is constructed that could set control parameters.. The fuzzy controller of draft–position mixed control is designed. After that, in-field experiments of position control was carried on, and the result of experiment shows the error of tillage depth was less than ±20mm. The experiment of draft-position control shown that the draft force and the tillage depth could be adjust by multi-parameter such as tillage depth, resistance coefficient and draft-position mixed coefficient. So that, the multi-parameter control strategy could improve the adaptability of tillage depth control in various soils and plow condition.

This paper presents a new kind of tilting-pad gas seal. This design is introduced to reduce the tangential seal force and to improve the stability of rotor system finally. A seal test rig is set up. The paper compares the leakage between tilting-pad seal and fixed pad seal. The result shows that the leakage ratio of the tilting-pad seal is close to the leakage ratio of the fixed pad seal. The work done by seal force on the cylinder system is calculated as an index of comparison between these two seals. Result shows that the work done by the fixed pad seal is greater than the work done by the tilting-pad seal. Moreover, system damping factor is used to compare the stabilities of these two seals. The impact tests on the cylinder system are done under different conditions. The system damping factors are calculated from the damped waves of system vibration. Test results show that the damping factor of the tilting pad seal is higher than that of the fixed pad seal in both the vertical and the horizontal directions.

In this study, the mercury content of 44 soil samples in Guan Zhong area of Shaanxi Province was used as the data source, and the reflectance spectrum of soil was obtained by ASD Field Spec HR (350-2500 nm) Comparing the reflection characteristics of different contents and the effect of different pre-treatment methods on the establishment of soil heavy metal spectral inversion model. The first order differential, second order differential and reflectance logarithmic transformations were carried out after the pre-treatment of NOR, MSC and SNV, and the sensitive bands of reflectance and mercury content in different mathematical transformations were selected. A hyperspectral estimation model is established by regression method. The results of chemical analysis show that there is a serious Hg pollution in the study area. The results show that: (1) the reflectivity decreases with the increase of mercury content, and the sensitive regions of mercury are located at 392 ~ 455nm, 923nm ~ 1040nm and 1806nm ~ 1969nm. (2) The combination of NOR, MSC and SNV transformations combined with differential transformations can improve the information of heavy metal elements in the soil, and the combination of high correlation band can improve the stability and prediction ability of the model. (3) The partial least squares regression model based on the logarithm of the original reflectance is better and the precision is higher, Rc2 = 0.9912, RMSEC = 0.665; Rv2 = 0.9506, RMSEP = 1.93, which can achieve the mercury content in this region Quick forecast.

By adding nano SiO2 particles, an enhanced K-PRTV anti-pollution flashover coating had been prepared. Optical profile meter (GT-K), atomic force microscopy (AFM), infrared spectrometer (FT-IR) and EDS characterization were carried out on the coating surface analysis. Those results has been use to optimize the further design and platform of the enhanced K-PRTV pollution flash coating experiment. It is also to improve the plan formulation, formulation optimization and preparation of the hydrophobic modified K-PRTV which is based on anti-pollution coating experiment. More importantly, the anti-pollution flashover K-PRTV coating with super hydrophobic modified is the great significance for K-PRTV coating.

Hydraulic transmission bedstand is one kind of the most commonly used in engineering machinery companies, and the bed structure is the most important part. Based on the original hydraulic transmission bedstand bed structure and the CAE technology, the original bed structure is improved. The optimized bed greatly saves the material of the production bed and improves the seismic performance of the bed. In the end, the performance of the optimized bed was compared with the original bed.

The problem of low efficiency of manual sorting packaging for the current tobacco distribution center, which developed a set of safe efficient and automatic type of alien smoke stack and packaging system. The functions of fully automatic alien smoke stack and packaging system adopt PLC control technology, servo control technology, robot technology, image recognition technology and human-computer interaction technology. The characteristics, principles, control process and key technology of the system are discussed in detail. Through the installation and commissioning fully automatic alien smoke stack and packaging system has a good performance and has completed the requirements for shaped cigarette.

The Goods-Falling device is an important device in the intelligent sorting goods sorting system, which is responsible for the temporary storage and counting of the goods, and the function of putting the goods on the conveyor belt according to certain precision requirements. According to the present situation analysis and actual demand of the domestic goods sorting equipment, a vertical type Goods - Falling Device is designed and the simulation model of the device is established. The dynamic characteristics such as the angular error of the opening and closing mechanism are carried out by ADAMS software. The simulation results show that the maximum angular error is 0.016rad. Through the test of the device, the goods falling speed is 7031/hour, the good of the falling position error within 2mm, meet the crawl accuracy requirements of the palletizing robot.

Using core wires with Ti-B4C-C as core and Al as strip materials, Ti(C,N)-TiB2-Al2O3 composite ceramic coatings were prepared on 45 steel substrates by the reactive arc spray technology. The influence of spray voltage, current, gas pressure and distance on the coatings was discussed. The spray parameters were optimized with porosity of the coatings as evaluation standard. The results showed that the most important factor which influences the quality of the coatings was spray distance. Then spray gas pressure, current and voltage followed in turn. The optimum process was spray current of 120A, voltage of 36, gas pressure of 0.7MPa and distance of 160mm. The porosity of coatings prepared in this spray process was only 2.11%. The coatings were composed of TiB2, TiC0.3N0.7, TiN, Al2O3 and AlN. Good properties and uniform distribution of these ceramic phases made the coatings have excellent comprehensive performances.

Aviation magneto ignition system failure accounted for two-thirds of the total fault aviation piston engine and above. At present the method used for this failure diagnosis is often depended on the visual inspections in the civil aviation maintenance field. Due to human factors, the visual inspections cannot provide ignition intensity value and ignition equilibrium deviation value among the different spark plugs in the different cylinder of aviation piston engine. So air magneto ignition strength and balance testing has become an aviation piston engine maintenance technical problem needed to resolve. In this paper, the ultraviolet sensor with detection wavelength of 185~260nm and driving voltage of 320V DC is used as the core of ultraviolet detection to detect the ignition intensity of Aviation magneto ignition system and the balance deviation of the ignition intensity of each cylinder. The experimental results show that the rotational speed within the range 0 to 3500 RPM test error less than 0.34%, ignition strength analysis and calculation error is less than 0.13%, and measured the visual inspection is hard to distinguish between high voltage wire leakage failure of deviation value of 200 pulse ignition strength balance/Sec. The method to detect aviation piston engine maintenance of magneto ignition system fault has a certain reference value.

In order to improve the movement accuracy of the robot, let the movement of the robot trajectory smoother, we design a third-order uniform acceleration / deceleration trajectory based on the Jerk value. Through the establishment of the mathematical model of the trajectory, combined with the logic control algorithm, constituted the core of the trajectory control. Finally, the StateFlow toolbox in Simulink as the carrier. Using the state module in StateFlow combined with the logic control conversion module, the third-order uniform acceleration and deceleration trajectory design is realized.

Sulfur hexafluoride (SF6) decomposition products were qualitatively and quantitatively analyzed by several gas chromatographs in the laboratory. Test conditions and methods were selected and optimized to minimize and eliminate the SF6' influences on detection of other trace components. The effective separation and detection of selected characteristic gases were achieved. And by comparison among different types of gas chromatograph, it was found that GPTR-S101 can effectively separate and detect SF6 decomposition products and has best the best detection limit and sensitivity. On the basis of GPTR-S101, online gas chromatograph for SF6decomposition products (GPTR-S201) was developed. It lays the foundation for further online monitoring and diagnosis of SF6.

The elongational properties of polyphenylene sulfide (PPS) melt were measured using a melt spinning technique. The relationship between extrusion temperature and melt strength (MS) as well as between elongational viscosity and drawability were investigated with respect to the effects of extrusion temperature and extensional strain rate on the melt extensional stress and elongational viscosity. The results showed that the stretching force for the PPS melt decreased with a rise of extrusion temperature while increased roughly with an increase of extensional rate. The MS decreased with an increase of temperature, and the ln MS was a linear function of 1/T when the extrusion velocity was constant. Both the melt extensional stress and elongational viscosity decreased with the increase of the extrusion temperature. With increase of the extensional strain rate, the extensional stress increased while the melt elongational viscosity first decreases and then increases gradually. A low melt elongational viscosity might be beneficial to improve the melt drawability.

Red mud was used to partially replace cement to prepare red mud concrete, with replacement rate of red mud mass being 0%, 5%, 10%, 15% and 20% respectively, and hydration age being 3d, 28d and 90d. The experiment of cube compressive strength and radioactivity were conducted for 90 cubical test pieces respectively. The results show that with rise of replacement rate of red mud, the cube compressive strength of red mud concrete at the same hydration age first increased and then decreased, leading to increase of content of 226Ra,232Th,40K in red mud concrete, and increase of material's radioactivity accordingly; as hydration age was prolonged, with the replacement rate of red mud being the same, the compressive strength increased, and internal and external exposure indices and total specific activity all increased yet with small increase range. Generally the hydration age does not significantly influence the radioactivity of red mud concrete.

The repair of nuclear spent fuel pool has a high requirement for the quality of welding, the welding speed directly affects the quality of the weld when local dry automatic underwater welding is used to repair the damaged surface. Under the condition of the same condition, the local dry automatic underwater welding test was carried out under the condition of the same welding condition. Taking the 20cm as the experimental condition, after massive experiments show that when the welding speed is approximately 48cm/min the weld quality is high, meeting the design requirements, based on the double layer shrinkage nozzle chamber of local dry underwater automatic welding.

In this paper we report the investigation of diamond-like carbon (DLC) deposited by microwave surface-wave plasma enhanced chemical vapor deposition (PECVD) on the polyethylene terephthalate (PET) web for the purpose of the barrier property improvement. In order to characterize the properties of DLC coatings, we used several substrates, silicon wafer, glass, and PET web and KBr tablet. The deposition rate was obtained by surface profiler based on the DLC deposited on glass substrates; Fourier transform infrared spectroscope (FTIR) was carried out on KBr tablets to investigate chemical composition and bonding structure; the morphology of the DLC coating was analyzed by atomic force microscope (AFM) on Si substrates. For the barrier properties of PET webs, we measured the oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) after coated with DLC films. We addressed the film barrier property related to process parameters, such as microwave power and pulse parameter in this work. The results show that the DLC coatings can greatly improve the barrier properties of PET webs.

A series of thermally conductive and electric-insulating epoxy composites filled with boron nitride (BN) modified by octadecyl trimethyl ammonium bromide and graphene nanosheets (GNP) were prepared. The effects of modified-BN (BNOTAB) and GNP content on thermal conductivity, electric-insulating and thermal stability properties of epoxy composite were investigated. The results indicate that the BNOTAB can homogeneously disperse into epoxy system. When the mass ratio of BNOTAB/GNP is 6:4 (total filler content is 10%), the thermal conductivity of the composites reached 0.48 W/(m·K), which is 108.7% higher than that of the neat epoxy. Meanwhile, the composite retains excellent electric-insulating property. TGA and DSC results showed that the addition of BNOTAB/GNP filler particles can improve the thermal stability of epoxy resin composites.

In order to overcome the difficulty of choosing appropriate grading parameters of filling material for mines which are using filling mining method, the fractal theory is introduced, and a fractal equation of grading is built to represent gradation. Meanwhile taken Dahongshan copper mine as an example to discuss the relationship between fractal dimension and porosity, cementing strength under different parameters. A prediction model of cementing strength is built based on the experimental data, and the results show that the optimal grading parameters of Dahongshan copper mine is fractal dimension = 2.82. The optimized grading parameters of filling material in Dahongshan run steady, which greatly reduced the filling cost.

In recent years, the number of the damage bridge due to excessive deformation gradually increased, which caused significant property damage and casualties. Hence health monitoring and the damage detection of the bridge structure based on the deflection measurement are particularly important. The current conventional deflection measurement methods, such as total station, connected pipe, GPS, etc., have many shortcomings as low efficiency, heavy workload, low degree of automation, operating frequency and working time constrained. GPS has a low accuracy in the vertical displacement measurement and cannot meet the dynamic measured requirements of the current bridge engineering. This paper presents a bridge health monitoring and damage detection technology based on digital image measurement method in which the measurement accuracy is sub-millimeter level and can achieve the 24-hour automatic non-destructive monitoring for the deflection. It can be concluded from this paper that it is feasible to use digital image measurement method for identification of the damage in the bridge structure, because it has been validated by the theoretical analysis, the laboratory model and the application of the real bridge.

High pressure air pipeline joint is important part of high pressure air system, whose reliability is related to the safety and stability of the system. This thesis developed a new type-high pressure air pipeline joint, carried out dynamics research on CB316-1995 and new type-high pressure air pipeline joint with finite element method, deeply analysed the join forms of different design schemes and effect of materials on stress, tightening torque and fatigue life of joint. Research team set up vibration/pulse test bench, carried out joint fatigue life contrast test. The result shows: the maximum stress of the joint is inverted in the inner side of the outer sleeve nut, which is consistent with the failure mode of the crack on the outer sleeve nut in practice. Simulation and experiment of fatigue life and tightening torque of new type-high pressure air pipeline joint are better than CB316-1995 joint.

In this study, to solve the poor water resistance and the low mechanical properties of starch, a mixed-starch composite matrix which including glycerol, sorbitol, and urea, were prepared via single-crew extrusion, then adding oil-flax to improve its physical mechanical and used to a source of biodegradable plastics material. The composite matrix was systematically characterized using various analytic tools including XRD, SEM and TG. The composite showed a maximum tensile strength of 18.11Mpa and moisture absorption 17.67%, while the original starch matrix was only 12.51 Mpa and 24.98%, respectively.

Heterostructural photonic crystals (HPC) have attracted considerable interest due to its large photonic bandgap. Here we report a facile method to calculate and fabricate the heterostructural photonic crystals by using optical transfer-matrix method and polystyrene (PS) spheres with different particle sizes. Results suggest that the numerical simulation match well with the experimental spectra. In addition, compared with the single-structural photonic crystals (SPC), the HPCs have larger photonic bandgap, which is equal to a total of the photonic bandgaps of each SPC. Therefore, the HPCs with large bandgap can be well designed and then synthesized.

In order to study the fragment initial velocity distribution of the cylindrical warhead with terminals and exploded in the air, this paper builds a theoretical calculation model of the side-wall and terminal velocity of the warhead with two terminals based on the energy conservation principle, and considering the explosive energy distribution and proportion. The calculation results obtained by the theoretical model are compared with the experimental results of previous scholars. In this paper, the influence of the warhead L/D and C/M on the side-wall and terminal initial velocity is examined. A good agreement between the theoretical calculation results and the experimental results of previous scholars is observed. This verifies feasibility of the calculation method proposed in this paper. When the warhead L/D is smaller than 2, along with increase of L/D, the side-wall fragment velocity increases and maintains at certain value. In terms of the terminal fragment initial velocity, when the warhead L/D is close to 1, the initial velocity is larger; but, when the L/D is larger than 1, the terminal fragment initial velocity decreases significantly.

Large deployable antennas are widely used in aerospace engineering to meet the envelop limit of rocket fairing. The high flexibility and low damping of antenna has proposed critical requirement not only for stability control of the antenna itself, but also for attitude control of the satellite. This paper aims to increase controllability of a large flexible antenna by modal optimization. Firstly, Sensitivity analysis of antenna modal frequencies to stiffness of support structure and stiffness of scanning mechanism are conducted respectively. Secondly, Modal simulation results of antenna frequencies are given, influences of scanning angles on moment of inertia and modal frequencies are evaluated, and modal test is carried out to validate the simulation results. All the simulation and test results show that, after modal optimization the modal characteristic of the large deployable antenna meets the controllability requirement well.

A mechanical impedance model of a coupled motor–shaft–bearing system has been developed to predict the dynamic characteristics and partially validated by comparing the computing results with finite element method (FEM), including the comparison of displacement amplitude in x and z directions at the two ends of the flexible coupling, the comparison of normalized vertical reaction force in z direction at bearing pedestals. The results demonstrate that the developed model can precisely predict the dynamic characteristics and the main advantage of such a method is that it can clearly illustrate the vibration property of the motor subsystem, which plays an important role in the isolation system design.

RV reducer and various mechanical transmission parts are widely used in eccentric shaft parts, The demand of precision grinding technology for eccentric shaft parts now, In this paper, the model of X-C linkage relation of eccentric shaft grinding is studied; By inversion method, the contour curve of the wheel envelope is deduced, and the distance from the center of eccentric circle is constant. The simulation software of eccentric shaft grinding is developed, the correctness of the model is proved, the influence of the X-axis feed error, the C-axis feed error and the wheel radius error on the grinding process is analyzed, and the corresponding error calculation model is proposed. The simulation analysis is carried out to provide the basis for the contour error compensation.

Tensegrity structures composing of continuous cables and discrete struts are under tension and compression, respectively. In order to determine the damage extents of tensegrity structures, a new method for tensegrity structural damage identification is presented based on flexibility disassembly. To decompose a tensegrity structural flexibility matrix into the matrix represention of the connectivity between degress-of-freedoms and the diagonal matrix comprising of magnitude informations. Step 1: Calculate perturbation flexibility; Step 2: Compute the flexibility connectivity matrix and perturbation flexibility parameters; Step 3: Calculate the perturbation stiffness parameters. The efficiency of the proposed method is demonstrated by a numeical example comprising of 12 cables and 4 struts with pretensioned. Accurate identification of local damage depends on the availability of good measured data, an accurate and reasonable algorithm.

The level set topology optimization method solved by reaction diffusion equation not only can avoid the occurrence of numerical problems such as checkerboard, but also can control the structural complexity of the optimization result through adjusting the value of regularization parameter. In this paper, the level set topology optimization method was used to study the multi-material problem, and the topological optimization mathematical model of the multi-material structure was established. Two methods of introduced element stress are studied. The typical example solved by this model has realized the reasonable layout of multi-material.

To meet the demand of large motion area and high natural frequency of the micro/nano positioning stage used in fast atomic force microscope(AFM), suitable material, actuator and displacement delivering mechanism were chosen and key factors that affected the performance such as input, output, and coupling displacement, driving force and natural frequency were simulated by finite element method(FEM). Finally, we manufactured the micro/nano positioning XY stage actuated by piezoelectric ceramics driver. Experimental results showed that natural frequency was 1.15kHz, maximum displacement was over 60μm along each axis and coupling rate was below 5%.

According to the demand of T2 terminal airlines to operate A380 models, to meet the smooth running of the A380 airliner at the west end of the Capital Airport, So Z3 and Z18 taxiway area of the transformation is imperative. According to the design, the upper layer of this project adopts SMA - 13 modified asphalt mastic macadam mixture. We design the SMA-13 modified asphalt mixture on Z3 and Z18 of the capital airport from any respects, including coarse and fine aggregate, filler, asphalt, fiber and anti-rutting agent, and we hope we can find the best SMA-13 modified asphalt mixture.

This study looked to determine what the optimum cooking loss for minced beef was when three different non-phosphate water retention additives (L-Arginine, sodium carbonate, and sodium citrate) were combined; the optimum value was determined using a Box–Behnken response surface design method. The optimum value was found to be 8.26%, and it was obtained when 0.29% L-Arginine, 0.45% sodium carbonate, and 0.24% sodium citrate were added to the beef.

Nanostructured mesoporous materials is a new type of porous materials, which has been widely used. It has excellent capability in enzymes immobilization, but modification on the chemical bonds of the enzyme reduce the enzymatic activity and rarely used in chemical reactions. The horseradish peroxidase was immobilized on the mesoporous materials with appropriate aperture and its activity and stability was evaluated when catalyzing the nitration reaction of amines and oxidation reaction of thiourea. The optimum mesoporous material to fix the horseradish peroxidase can be obtained by mixing polyoxyethylene - polyoxypropylene-pol, yoxyethylene(P123), 1,3,5-trimethylbenzene(TMB), and tetramethoxysilane (TMOS) at a ratio of 10:1:1, whose surface area and pore volume and pore diameter calculated by BET and BJH model were 402.903m²/g, 1.084cm²/g, 1.084cm²/g respectively. The horseradish peroxidase, immobilized on the mesoporous materials, was applied for catalyzing the nitration reaction of anilines and oxidation reaction of thiourea, produced a high product yield and can be recycled. Thus, it is a strong candidate as a catalysts for oxidation reactions, to be produced at industral scale, due to its high efficiency and low cost.

This paper describes for the first time the analysis of inner microstructure of cotton fibrous assemblies using computed tomography. Microstructure parameters such as packing density, fractal dimension as well as porosity including open porosity, closed porosity and total porosity are calculated based on 2D data from computed tomography. Values of packing density and fractal dimension are stable in random oriented fibrous assemblies, and there exists a satisfactory approximate linear relationship between them. Moreover, poles analysis indicates that porosity represents the tightness of fibrous assemblies and open poles are main existence.

This article presents the effects of quenching temperature on tempering microstructure, mechanical properties and wear resistance of 30MnB steel were studied. The results showed that: The microstructure of 30MnB steel was the tempered martensite and retained austenite after quenching at 840°c-900°c and then tempering at 200°c. the carbide precipitation did not occur when 30MnB steel was tempered at 200°c, only the carbon segregation occurred. Meanwhile, the tensile strength of 30MnB was all above 1350MPa after quenching at 840°c-900°c and then tempering at 200°c, the -40°c ballistic work was above 20J, indicating that it had good low temperature impact toughness. 30MnB had minimum abrasion loss after quenching at 880°c and then tempering at 200°c, the wear morphology was fine wear mark, shallow furrow and ridge augmentation.

In this paper, it uses the way of dry bath temperature to heat the microfluidic chip directly by the heating plate and the liquid sample in microfluidic chip is heated through thermal conductivity, thus the liquid sample will maintain at target temperature. In order to improve the reliability of the whole machine, a temperature control system based on SG3525 is designed.SG3525 is the core of the system which uses PWM wave produced by itself to drive power tube to heat the heating plate. The bridge circuit consisted of thermistor and PID regulation ensure that the temperature can be controlled at 37 °C with a correctness of ± 0.2 °C and a fluctuation of ± 0.1 °C.

Discrete element method has great advantages in simulating the contacts, fractures, large displacement and deformation between particles. In order to analyze the spatial distribution of the shear surface in the three-dimensional triaxial test, a measurement model is inserted in the numerical triaxial model which is generated by weighted average assembling method. Due to the non-visibility of internal shear surface in laboratory, it is largely insufficient to judge the trend of internal shear surface only based on the superficial cracks of sheared sample, therefore, the measurement model is introduced. The trend of the internal shear zone is analyzed according to the variations of porosity, coordination number and volumetric strain in each layer. It shows that as a case study on confining stress of 0.8 MPa, the spatial shear surface is calibrated with the results of the rotated particle distribution and the theoretical value with the specific characteristics of the increase of porosity, the decrease of coordination number, and the increase of volumetric strain, which represents the measurement model used in three-dimensional model is applicable.

Generalized uncertainty principle (GUP), also known as the generalized uncertainty relationship, is the modified form of the classical Heisenberg's Uncertainty Principle in special cases. When we apply quantum gravity theories such as the string theory, the theoretical results suggested that there should be a "minimum length of observation", which is about the size of the Planck-scale (10^-35m). Taking into account the basic scale of existence, we need to fix a new common form of Heisenberg's uncertainty principle in the thermodynamic system and make effective corrections to statistical physical questions concerning about the quantum density of states. Especially for the condition at high temperature and high energy levels, generalized uncertainty calculations have a disruptive impact on classical statistical physical theories but the present theory of Femtosecond laser is still established on the classical Heisenberg's Uncertainty Principle. In order to improve the detective accuracy and temporal resolution of the Femtosecond laser, we applied the modified form of generalized uncertainty principle to the wavelength, energy and pulse time of Femtosecond laser in our work. And we designed three typical systems from micro to macro size to estimate the feasibility of our theoretical model and method, respectively in the chemical solution condition, crystal lattice condition and nuclear fission reactor condition.

All manuscripts must be in English, also the table and figure texts, otherwise we cannot publish your paper. Please keep a second copy of your manuscript in your office. When receiving the paper, we assume that the corresponding authors grant us the copyright to use the paper for the book or journal in question. Should authors use tables or figures from other Publications, they must ask the corresponding publishers to grant them the right to publish this material in their paper.

The mechanical processing has high complexity, strong coupling, a lot of control factors in the machining process, it is prone to failure, in order to improve the accuracy of fault detection of large mechanical equipment, research on fault trend prediction requires machining, machining fault trend prediction model based on fault data. The characteristics of data processing using genetic algorithm K mean clustering for machining, machining feature extraction which reflects the correlation dimension of fault, spectrum characteristics analysis of abnormal vibration of complex mechanical parts processing process, the extraction method of the abnormal vibration of complex mechanical parts processing process of multi-component spectral decomposition and empirical mode decomposition Hilbert based on feature extraction and the decomposition results, in order to establish the intelligent expert system for the data base, combined with large data analysis method to realize the machining of the Fault trend prediction. The simulation results show that this method of fault trend prediction of mechanical machining accuracy is better, the fault in the mechanical process accurate judgment ability, it has good application value analysis and fault diagnosis in the machining process.

4Wetting phenomenon is an important phenomenon in nature, and it is related to our daily life closely. Therefore, it is of great practical significance to study wettability surface. Recently, based on the observation and measurement of Nepenthes surface, we realized the liquid or insects will roll down from the surface almost without resistance resulted from the lunate-shaped microstructure and its composite microstructure, which can make the surface possess superhydrophobic properties. Nepenthes Bio-inspired superhydrophobic primary microstructure was fabricated by the two-photon polymerization using femtosecond laser and characterized by developering are still stable after washing observed by Zygo. The lunate are still intact after washing, so the character of hydrophobicity can be maintained. We demonstrate that our approach provide a novel way to fabricate such primary microstructures on the glass using femtosecond laser two-photon polymerization for practical applications in related area. 97714025@qq.com

The investigation was conducted to study the fatigue behavior of steel fiber reinforced high-strength concrete (SFRHSC) beams. A series of 5 SFRHSC beams was conducted flexural fatigue tests at different stress level S of 0.5, 0.55, 0.6, 0.7 and 0.8 respectively. Static test was conducted to determine the ultimate static capacity prior to fatigue tests. Fatigue modes and S-N curves were analyzed. Besides, two fatige life prediction model were analyzed and compared. It was found that stress level S significantly influenced the fatigue life of SFRHSC beams and the fatigue behavior of SFRHSC beams was mainly determined by the tensile reinforcement.

In order to study fatigue performance of foamed lightweight soil and forecast its fatigue life in the supporting project, on the base of preliminary tests, beam fatigue tests on foamed lightweight soil is conducted by using UTM-100 test system. Based on Weibull distribution and lognormal distribution, using the mathematical statistics method, fatigue equations of foamed lightweight soil are obtained. At the same time, according to the traffic load on real road surface of the supporting project, fatigue life of formed lightweight soil is analyzed and compared with the cumulative equivalent axle loads during the design period of the pavement. The results show that even the fatigue life of foamed lightweight soil has discrete property, the linear relationship between logarithmic fatigue life and stress ratio still performs well. Especially, the fatigue life of Weibull distribution is more close to that derived from the lognormal distribution, in the instance of 50% guarantee ratio. In addition, the results demonstrated that foamed lightweight soil as subgrade filler has good anti-fatigue performance, which can be further adopted by other projects in the similar research domain.

The effect of nitrogen removal was investigated using a Bamboo filament bioreactor to treat wastewater with high organic load and low C/N ratio. Results showed that total nitrogen removal efficiency was 26.6∼96.95%, effluent BOD/COD ratio was 0.07∼0.74 when influent COD was 790∼5000 mg/L, BOD 60.0∼1100mg/L and the BOD/COD ratio was respectively 0.02∼0.44. When COD was 130.0∼278.0 mg/L, BOD was 42.5∼96.7mg/L, NH₄⁺-N was 16.2∼98.1mg/L, TN was 28.7∼103.8 mg/L, COD/TN was 1.6∼4.7, TN removal rate was 29.4%∼58.8%. This indicated that good TN removal efficiency can be achieved when using a Bamboo filament bioreactor to treat wastewater with high organic load and low C/N ratio; Nitrogen removal fluctuated was due to secretion of bamboo juice secreted from the cavity of filamentous bamboo. The distribution characteristics of the main bacteria was investigated to show that total number of bacteria at inlet and outlet were same roughly during the wastewater treatment, while bacteria, nitrifying bacteria were distributed in outlet, and Nitrifying bacteria accounted for 1.57% of total bacteria, while denitrifying bacteria evenly distributed in the reactor.

Nonlinear constitutive modeling of piezoelectric ceramics is discussed in this paper. Van der Pol item is introduced to explain the simple hysteretic curve. Improved nonlinear difference items are used to interpret the hysteresis phenomena of piezoelectric ceramics. The fitting effect of the model on experimental data is proved by the partial least-square regression method. The results show that this method can describe the real curve well. The results of this paper are helpful to piezoelectric ceramics constitutive modeling.

In this paper, a kind of giant magnetostrictive force sensor is proposed, ans its magneto-mechanical coupled model is developed. The relationship between output voltage of giant magnetostrictive force sensor and input excitation force is obtained. The phenomena of accuracy aggravation in high frequency and delay of giant magnetostrictive sensor are explained. The experimental results show that the model can describe the actual response of giant magnetostrictive force sensor. The new model of giant magnetostrictive sensor has simple form and is easy to be analyzed in theory, which is helpful to be applied in measuring and control fields.

The effect of melting point on the physical properties of anhydrous milk fat were investigated. The results showed that high melting fractions (HMF) (S30,S35) were enriched in long-chain fatty acids, whereas low melting fractions (LMF)(S5,S10,S15) were enriched in short-chain and unsaturated fatty acids. From S5 to S35, enthalpy value was gradually increased on both crystallization and melting condition, so as SFC on different temperature. The mixture and chemical interesterification allowed obtaining fats with various degrees of plasticity, increasing the possibilities for the commercial use of different fraction of AMF.

This paper presents the determination of betaine content in Lycii Cortex by high performance capillary electrophoresis (HPCE) method. The borax solution was chosen as buffer solution, and its concentration was 40 mmol at a constant voltage of 20kV and injecting pressure time of 10s at 14°C. Linearity was kept in the concent ration range of 0.0113∼1.45mg of betaine with correlation coefficient of 0.9. The content of betaine in Lycii Cortex was 61.9 mg/g (RSD = 13.4%) (n = 7). The recovery was in the range of 86.6% - 118.1% (n=4). This method is specific, simple and rapid and accurate, which is suitable for the detection of the content of betaine in Lycii Cortex.

This paper presents the determination of betaine content in Lycium barbarum L. by high performance capillary electrophoresis (HPCE) method. The borax solution was chosen as buffer solution, and its concentration was 40 mmol at a constant voltage of 20kV and injecting pressure time of 10s at 20°C. Linearity was kept in the concent ration range of 0.0113∼1.45mg of betaine with correlation coefficient of 0.9. The recovery was in the range of 97.95%∼126% (n=4). The sample content of betaine was 29.3mg/g and RSD 6.4% (n=6). This method is specific, simple and rapid and accurate, which is suitable for the detection of the content of betaine in Lycium barbarum L.

This paper presents the determination of betaine content in jujube by high performance capillary electrophoresis (HPCE) method. The borax solution was chosen as buffer solution, and its concentration was 40 mmol at a constant voltage of 20kV and injecting pressure time of 10s at 14°C. Linearity was kept in the concent ration range of 0.0113∼1.45mg of betaine with correlation coefficient of 0.9. The content of betaine in jujube was 85.91 mg/g (RSD = 16.6%) (n = 6). The recovery of betaine in jujube sample was in the range of 86.2% - 116.6% (n=3). This method is specific, simple and rapid and accurate, which is suitable for the detection of the content of betaine in jujube.

This paper presents the determination of betaine content of Forsythia suspensa by high performance capillary electrophoresis (HPCE) method. The borax solution was chosen as buffer solution, and its concentration was 40 mmol with capillary column (75μm×52/60cm) at a constant voltage of 20kV and injecting pressure time of 10s at 20°C. Linearity was kept in the concent ration range of 0.0113-1.45mg·ml-1 of betaine with correlation coefficient of 0.999. The recovery was in the range of 97%-117% (n=5), The content of betaine was 281.5 mg·g-1and RSD value of 9.6% (n=6) in Forsythia suspensa. This method has the advantage of rapid, accurate and good repeatability in separation and determination of betaine in Forsythia suspensa.

Cardiac and cerebrovascular disease is a common disease. It is well recognized that antiplatelet agent is effective in the prevention and treatment of thrombosis. Clopidogrel is one of thieno pyridine derivatives, which can inhibit ADP-induced platelet aggregation. The preparation methods of Clopidogrel were reviewed and Clopidogrel was finally synthesized from 2-chlorobenzyl cyanide via bromination, condensation, hydrolyze, esterification, resolution, Finally with the sulfate, re-crystallization product of the target compound clopidogrel. The overall yield is 16%. Synthesis of the intermediate product and finally the structure of the product through ESI and ¹H-NMR corroboration. The improved synthetic procedure has the advantage of low cost and is suitable for industrial production.

In response to the Ministry of agriculture's action plan for chemical fertilizer reductions and organic fertilizers instead of fertilizersand discuss the optimum consumption and proportion of peanut biochar-based fertilization.Six different fertilization treatments were set up:C40, C50(standard consumption), C60, C40+M, C30+M and C20+M. Seelding height, chlorophyll content and total biomass were also measured on 6th, 2017. The results showed that C20+M treatment had the highest plant height and the highest biomass in Peanut Seedlings, while the content of chlorophyll increased with the amount of biochar applied.

A glass carbon electrode was prepared that coated with a composite film containing grapheme and multi-walled carbon nanotubes. It was used to study the electrochemical response of terbutaline sulfate. Under the optimized conditions, the oxidation peak current was found to be proportional to its concentration in the range of 0.2-5 μmol·L^-1 and 5-40 μmol·L^-1).Compared with the bare GC electrode, the GN-MWNTs-modified GC (GN-MWNTs/GC) had many advantages such as relatively high sensitivity, good stability and long life time. The modified electrode was used to determine the TES tablets with satisfactory results.

The three-dimensional numerical simulation of the glass melt flowing out from the slit was conducted by Semi-Implicit Method for Pressure Linked (SIMPLE) and volume of fluid (VOF) method with the software FLUENT. In this work, the effect of liquid level of glass melt, viscosity of glass melt, width and height of the slit on flow rate was investigated. The simulation results showed that the flow of glass melt was proportional to the height of the liquid surface and the square of the slit width, and inversely proportional to the viscosity of the glass melt and the height of the slit. It was concluded that high liquid level and low viscosity should be adopted in the drawing process of the flexible glass sheet.

Rubidium, cesium and its compounds play an important role in traditional and high-tech fields. This paper focuses on the research status of separation rubidium and cesium in brine using solvent extraction, and briefly introduced the characteristics of this method, which can be used to realize industrial production of rubidium and cesium from brine.

It is well known that the comprehensive utilization of the Salt Lake resources successfully must be guided corresponding to the aqueous phase equilibria and phase diagrams. Researches on the phase relationships of brine systems containing calcium and strontium ions are essential to promote the development for the relative resources discovered in China at recent years. In this paper, the phase equilibria of calcium-containing systems, strontium-containing systems and calcium-strontium coexisted brine systems around the world were reviewed. The problems existed recently and new trends in future were point out.

It is well known that the phase chemistry is of great importance in the fields of chemistry, chemical engineering, and the separation and purification of minerals from brine. To effectively employ the resources containing lithium, magnesium and borate, the study on phase equilibrium is essential to the comprehensive utilization of the Salt Lake resources. In this paper, progresses on phase equilibria of salt-water systems containing lithium, magnesium and borate were presented.

Introduced the present status of chain boiler efficiency is low, the system analysis of the chain boiler optimization and upgrading of technology, for the whole progress of chain boiler to provide some ideas and reference.

Monolayer molybdenum disulfide (MoS2) and molybdenum diselenide (MoSe2) have attracted a great attention for their exceptional electronic and optoelectronic properties among the two dimensional family. However, controllable synthesis of monolayer crystals with high quality needs to be improved urgently. Here we demonstrate a chemical vapor deposition (CVD) growth of monolayer MoS2 and MoSe2 crystals using three-temperature-zone furnace. Systematical study of the effects of growth pressure, temperature and time on the thickness, morphology and grain size of crystals shows the good controllability. The photoluminescence (PL) characterizations indicate that the as-grown monolayer MoS2 and MoSe2 crystals possess excellent optical qualities with very small full-width-half-maximum (FWHM) of 96 me V and 57 me V, respectively. It is comparable to that of exfoliated monolayers and reveals their high crystal quality. It is promising that our strategy should be applicable for the growth of other transition metal dichalcogenides (TMDs) monolayer crystals.

Power plant boiler is one of the three main equipment of coal-fired power plants, is very tall to the requirement of the safe and stable operation, in a significant role in the whole system of thermal power generation, a risk-based inspection is a kind of pursuit of security and economy of unified system management idea and method, can effectively evaluate equipment risk and reduce the operational cost.

The Zn₃V₂O₈ and (Zn_1-xEu_x)₃V₂O₈ have been production by Solid phase method. The crystal structure, the crystal morphology and the luminescence property of Zn₃V₂O₈ and (Zn_1-xEu_x)₃V₂O₈ have been studied. Based on the first-principles planar wave super-soft pseudopotential method of density functional theory (DFT), the α-Zn₃V₂O₈ crystal model was used to calculate the electronic structure and optical properties of the model. The results show that the crystal structure of Zn₃V₂O₈ and (Zn_1-xEu_x)₃V₂O₈ were the same, and the particle uniformity of (Zn_1-xEu_x)₃V₂O₈ was better than Zn₃V₂O₈. The emission band Zn₃V₂O₈ and (Zn_1-xEu_x)₃V₂O₈ were present at the wave length of 420-690 nm and 300-400nm, the luminescence property of (Zn_1-xEu_x)₃V₂O₈ was enhance by Eu-doped. α-Zn₃V₂O₈ is an indirect band gap, α-Zn₃V₂O has a band gap of 2.715eV, pure α-Zn₃V₂O₈ has a peak, appeared at 3.91eV that is caused by the optical transition between V 3d and O 2p states.

Rotating machinery plays an important role in all walks of life. Once the equipment fails, equipment maintenance and shutdown will cause great social harm and economic losses. Equipment safety operations at nuclear power stations have always been of top priority. It is prone to noise when the equipment is out of order or aging. Failure to find or develop equipment at the initial stage of equipment failure or ageing will pose a serious threat to the safety of the plant's equipment. In this paper, sound imaging diagnosis technology is applied as a supplementary method to the condition monitoring and diagnosis system of rotating machinery in nuclear power stations. It provides a powerful guarantee for the condition monitoring and fault diagnosis of rotating machinery in nuclear power stations.

PEN/NdFeB composite films were prepared by the solution casting method. The thermal properties, fracture morphology and tensile strength of the composite films were tested by DSC, TGA, SEM and electromechanical universal testing machine, respectively. The results reveal that the composite film has good thermal properties and tensile strength. Glass-transition temperature and decomposition temperatures at weight loss of 5% ot the composite films retain at 166±1 C and 462±4 C, respectively. The composite film with 5 wt.% NdFeB has the best tensile strength value for 100.5 MPa. In addition, it was found that the NdFeB filler was well dispersed in PEN matrix by SEM analysis.

An AIEgen 1, 2-di (4-hydroxyphenyl)-1, 2-diphenylethene (TPE-2OH) was introduced into the back bone of semi-crystalline poly arylene ether nitriles (PEN). The fluorescence spectra results indicated that the derived polymer displayed a typical aggregation-induced emission enhancement (AIEE) active with an emitting peak at ∼470 nm. Then the AIEE active PEN was prepared into films through casting method and realised strong fluorescence emission and excellent mechanics properties. Besides, the crystal AIEE active polymer shows sphere micro-morphology along with a strong blue emission. These findings will open a door for further research on the high performance semi-crystalline PEN at flexible display technology and optical sensors.

A novel magnetic g-C₃N₄ (Fe₃O₄-g-C₃N₄) was prepared in one step and used to removal Cd (II) from aqueous solution. VSM, FT-IR, SEM, laser particle analyses and XRD were used to character Fe₃O₄-g-C₃N₄. The kinetic data was more descibed by Peseudo-second-order model. Langmuir model to describe isotherms data is more convincing and the predicated maxmium adsorption capacity for Cd (II) is 204.5 mg/g.

To improve the quality of high-moisture anthracite treated by hydraulic reservoir reconstruction technologies, the isothermal drying process of anthracite were studied experimentally. Based on the experiment results, after the fitting of thin layer drying model and the regression analysis, the prediction model was established. The results show that the isothermal drying process can be divided into the acceleration and deceleration stage. The effective water diffusivity increases with the increase of temperature and particle size. And the Page model fits the best. The prediction model is in good agreement with experimental data.

In this study, PC-nanoTiO₂ and PC-P25 were prepared via chemical-deposition and mixture-calcination methods, respectively. Both of PC-nanoTiO₂ and PC-P25 were employed to adsorb and photocatalytic degrade toluene in aqueous solution. The characterization results show that distribution of TiO₂ nanoparticles in PC-nanoTiO₂ and PC-P25 were different, but their binding force between PC and TiO₂ were both chemical bonds. Due to synergy of adsorption and photocatalytic degradation, both PC-nanoTiO₂ and PC-P25 exhibit good effect in removing toluene in aqueous solution, and both PC-nanoTiO₂ and PC-P25 could be utilized for treating wastewater generated from hazardous chemicals leakage accidents emergency.

Photocatalytic and photo electrochemical (PEC) degradation of chlorsulfuron herbicide were studied. Two novel PEC electrodes Ti/IrO2-Pt-WO3 (TIW) and Ti/IrO2-Pt-Ag3PO4 (TIA) were designed and some important factors were studied. Lower current density showed lower removal efficiency than higher conditions by electrochemical method. Furthermore, PEC showed higher degradation efficiency than the sum of individual EO and photocatalytic methode.

Orange-red phosphors NaY(WO₄)₂:Eu³⁺, Sm³⁺ were successfully synthesised by hydrothermal synthesis method. The photoluminescence (PL) properties were investigated. The PL emission spectrum of Na Y (WO⁴)²: Eu³⁺ shows good luminous properties under 398 nm, which mainly located at 596 and 615 nm, with the additional of Sm³⁺ could broaden and increase emission intensity of Eu³⁺, which could be suitable for the excitation of UV light emitting diodes (LEDs) (∼400 nm). The PL results indicated that Na Y (WO₄)₂: Eu³⁺, Sm³⁺ may be a promising red phosphor candidate for use in white LEDs.

In view of the large heavy slewing bearing no longer follows the rigid ring hupothesis under the load condition, the entity finite element model of thrust angular contact ball bearing was established by using finite element analysis software ANSYS. The boundary conditions of the model were set according to the actual condition of slewing bearing, the internal stress state of the slewing bearing was obtained by solving and calculation, and the calculated results were compared with the numerical results based on the rigid ring assumption. The results show that more balls are loaded in the result of finite element method, and the maximum contact stresses between the ball and raceway have some reductions. This is because the finite element method considers the ferrule as an elastic body. The ring will produce structure deformation in the radial plane when the heavy load slewing bearings are subjected to external loads. The results of the finite element method are more in line with the actual situation of the slewing bearing in the engineering.

The general aviation system is an open and dissipative system with complex structures and behavioral features. This paper has established the system model and network model for general aviation. We have analyzed integral attributes and individual attributes by applying the complex network theory and concluded that the general aviation network has influential enterprise factors and node relations. We have checked whether the network has small world effect, scale-free property and network centrality property which a complex network should have by applying degree distribution of functions and proved that the general aviation network system is a complex network. Therefore, we propose to achieve the evolution process of the general aviation industrial chain to collaborative innovation cluster of advanced-form industries by strengthening network multiplication effect, stimulating innovation performance and spanning the structural hole path.

In order to find out the effect of fluid flow velocity on electrochemical reaction, the electrochemical parameters of super 13Cr stainless steel in 3.5% NaCl aqueous solution were measured by a jet flow system at different flow velocities. The electrochemical characters such as open-circuit potential and polarization curve were monitored online using a three-electrode electrochemical system. The results show that the increase of wall shear stress caused by the high flow velocity leads to the rupture of passive films and the exposure of fresh metal in the corrosive media, which causes the increase of corrosion rate. Meanwhile, the corrosion rate shows a significant growth when the flow velocity is less than 0∼10.0 m/s. But it gradually decreases after reaching a maximum value.

In view of the galvanic corrosion of the tower wall material in the tower of a refinery atmospheric vacuum distillation unit, the electrochemical behavior of Q345R steel, stainless steel (201, 304 cold-rolled plate, 304 hot rolled plate and 316L) in 3.5%NaCl solution was studied by electrochemical method. The results show that the corrosion potential of Q345R is much lower than that of stainless steel, and the corrosion rate of Q345R is higher than that of stainless steel. As the anode is etched as the anode corrosion, the anode polarizability of stainless steel shows strong polarization ability, which is anodic polarization control, and Q345R is anode Active polarization control; Q345R / 201 galvanic pair may be the most serious corrosion, and Q345R/316L galvanic couple may be relatively slight. Therefore, in the actual production of tower equipment, material design or tower to upgrade the replacement, it are recommended to use the preferred anode and cathode potential difference with the use of materials.

When the acoustic fuse of smart landmines tries to detect and recognize a ground vehicle target, it is usually affected by gun shooting, explosive blasting or other similar noises on the actual battlefield. To improve the target recognition of smart landmines, it would be necessary to study the characteristics of these acoustic signals. Using sample data of the shooting noise of a certain type of rifle, the blasting noise of TNT, and the acoustic signals of a certain type of WAV, the energy characteristics of these noise signals are compared and analyzed. The result shows that the wavelet-packet energy method is effective in describing the characteristics of these acoustic signals with distinct intertype variations, and the frequency at the peak energy value can serve as a signature parameter for recognizing battlefield blasting noise signals from vehicle target signals.

By adding nano SiO2 particles, an enhanced K-PRTV anti-pollution flashover coating had been prepared. Optical profile meter (GT-K), atomic force microscopy (AFM) and infrared spectrometer (FT-IR) characterization were carried out on the coating surface analysis. With the use of modified epoxy resin as the base material, the supplemented by phosphate as a corrosion stabilizer, to achieve a corrosion of steel and galvanized steel with rust coating. Paint with excellent adhesion, more than 10MPa (1), resistant to neutral salt spray 1000h does not appear rust point. At the same time coating a large amount of ultra-fine zinc powder can be added for the tower galvanized layer zinc repair function, while the paint in the zinc powder for the tower to provide sacrificial anode protection, to achieve self-repair function of the coating. Compared to the market with a significant reduction in the cost of rust paint, enhance the anti-corrosion properties.

The piezoelectric shunt damping circuit using current mode approach is imposed to control the vibration of a cantilever beam. Firstly, the simulated inductance with large values are designed for the corresponding RL series shunt circuits. Moreover, with an example of cantilever beam, the second natural frequency of the beam is targeted to control for experiment. By adjusting the values of the equivalent inductance and equivalent resistance of the shunt circuit, the optimal damping of the shunt circuit is obtained. Meanwhile, the designed piezoelectric shunt damping circuit stability is experimental verified. Experimental results show that the proposed piezoelectric shunt damping circuit based on current mode circuit has good vibration control performance. However, the control performance will be reduced if equivalent inductance and equivalent resistance values deviate from optimal values.

Aiming at the trouble phenomenon for bevel gear teeth surface damage of Aero-engine, Fault Tree of bevel gear teeth surface damage was drawing by logical relations, the possible cause of trouble was analyzed, scanning electron-microscope, energy spectrum analysis, Metallographic examination, hardness measurement and other analysis means were adopted to investigate the spall gear tooth. The results showed that Material composition, Metallographic structure, Micro-hardness, Carburization depth of the fault bevel gear accord with technical requirements. Contact fatigue spall defect caused bevel gear teeth surface damage. The small magnitude of Interference of accessory gearbox install hole and driving bevel gear bearing seat was mainly caused. Improved measures were proposed, after proof, Thermoelement measures are effective.

Domestic Aramid Fiber III (DAF III) was modified by oxygen plasma treatment. The fiber surface characteristics was observed by Scanning Electron Microscopy. The results showed that oxygen plasma treatment changed surface morphologies. The effects of oxygen plasma treatment on DAF III reinforced bismaleimides (BMI) composite bending and interfacial properties were investigated, respectively. The ILSS value increased from 49.3 MPa to 56.0 MPa (by 13.5%) after oxygen plasma treatment. The bending strength changed a little. Furthermore, the composite rupture mode changed from interfacial rupture to fiber or resin bulk rupture.

LiFePO₄ was prepared via high temperature solid-state method at different heat preservation time. XRD and SEM was used to test the structure and morphology of LiFePO₄. Land 2001 was used to test the electrochemical performance of LiFePO₄. The results illustrated that well-crystallized LiFePO₄ composite with homogeneous small particles was obtained by XRD and SEM. And the optimum heat preservation time was 4 hour. From charge/discharge test, it can be seen that at 0.2C, LiFePO₄ has initial discharge capacities of 159.1mAh/g at the heat preservation time 4 hour. From the rate capacity, it can be seen that the discharge capacity was of optimum sample remains above 99% after 200 cycles.

The experimental study on the energy relationship between the coarse sand with different water content and the concrete interface with different hardness and roughness is carried out, through the high stress direct shear apparatus. Experimental results show that the growth rate of shear energy dissipation of sand - structure contact surface is slowing down with the increase of roughness, even negative; The shear energy dissipation of concrete with different hardness decreases first and then increases with the increase of water content, The crushing energy consumption is the lowest when water content is 16%; The shear energy dissipation at different moisture content increases with the increase of the contact strength of concrete structure.

The monodisperse crosslinked polymer microspheres have attracted much attention because of their superior thermal and solvent resistance, mechanical strength, surface activity and adsorption properties. They are of wide prospects for using in many fields such as biomedicine, electronic science, information technology, analytical chemistry, standard measurement and environment protection etc. Functional polymer microspheres prepared by different methods have the outstanding surface property, quantum size effect and good potential future in applications with its designable structure, controlled size and large ratio of surface to volume. Scholars of all over the world have focused on this hot topic. The preparation method and research progress in functional polymer microspheres are addressed in the paper.

As a kind of novel bio-mimetic carbon fibers, with diversities of high functions, carbon microcoils (CMC) have the outstanding properties of high specific strength, low-density, large specific surface area, heat resistance, corrosion resistance, chemical stability, conductive ability and thermal conductivity. Due to their special three-dimensional spiral structure, they have the chiral characteristics and a high flexibility. Carbon microcoils has become a research hotspot, especially the preparation of polymer-based carbon microcoils composite materials and they have wide more application such as flexible sensors, electromagnetic shielding materials, hydrogen storage materials, health care products and so on.

The microscopic morphology of the plugging agent was observed by scanning electron microscope. Double crosslinking system has dense pores and full structure. The outer network in the double crosslinked gel is filled into the voids of the network. This mainly forms a secondary network in the form of filling, which can greatly improve the water retention and viscoelasticity of the gel. Based on microscopic morphology, the principle of high efficiency plugging was analyzed. The water plugging in the well is simulated by visual model, and the selective plugging effect of double crosslinked gel is observed more intuitively.

The ore-forming fluid system of bauxite in Wuchuan-Zheng,an-Daozhen (short for WZD) Area of northern Guizhou Province was studied from the perspective of deposit formation mechanism. It was discovered that ore-forming fluids were mainly effective for transporting and leaching during the formation of bauxite. The means of transport mainly included colloidal transport, suspended transport and gravity flow transport. In the course of their leaching, fluids had a range of chemical reactions, as a result of which elements such as silicon and iron migrated downwards. In this process, properties of fluids changed as well.

A novel dinuclear dysprosium complex, namely [Dy2 (L) 4 (COO) 2 (CH3OH)2] (1) (L = 2-hydroxy-3-methodxybenzaldehyde-5-bromo oxime), was synthesized, structurally and magnetically characterized. Single-crystal X-ray structural analysis reveals that complex 1 is neutral dinuclear complex, in which two Dy(III) ions with nine-coordinated environment are bridged by two phenoxide groups from two schiff base ligands and four O ions from two molecules of methanoic acid. The magnetic study of complex 1 indicates the slow relaxation of magnetization.

Burdock Fructooligosaccharide (BFO) were sulfated using SO3-Py complex. The maximal degree of sulfonation (DSsulf) was 1.56, which were obtained by varying reaction factor such molar ratio of SO3-Py to fructofuranans unit (FU). The FT-IR, 1H NMR and 13C NMR spectra showed the introduction of sulfate group, and the reaction occurred at C-6, C-4 and C-3 in the fructofuranans unit of BFO. The molecular weight estimated by HPGPC were 6104.7-11003.3 g/mol for S-BFO (DS sulf=1.2).

The superplastic mechanical properties and microstructure evolution of the duplex Mg-9Li-1Al alloy were investigated. The tensile testing results show that, the elongation of the as-extruded Mg-9Li-1Al alloy reaches 510% at 573 K with a strain rate of 2×10-4 s-1. During the deformation process, the strips of α phase break into equiaxed structure. This phenomenon can be attributed to a particular dynamic recrystallization, which suggests that the β phase can recrystallize in the α phase due to the small misfit degree between α phase and β phase.

A graphene/poly (vinyl alcohol) composite hydrogel based on poly (N-methylolacrylamide-methyl acrylate) was prepared. The additon of GO evidently change the network structure and enhance the pH sensitivity of hydrogel. The stucture of hydrogel was characterized by SEM and XRD. Factors influencing the swelling behavior of hydrogel were investigated, such as monomer component and GO. In additon, the reversibility of pH sensitivity of hydrogel was studied as well, which will have a good application in drug release field.

A novel graphene oxide-polyvinyl alcohol/poly (N-isopropylacrylamide) hydrogel (GO-PVA/PNIPA hydrogel) with temperature sensitivity is prepared through in situ free-radical polymerization and freezing–thawing cyclic process. In this study, mechanical property and temperature sensitive property of GO-PVA/PNIPA hydrogel are investigated. The results show that the mechanical strength of GO-PVA/PNIPA hydrogels are enhanced with the increasing content of GO and also keeps good temperature sensitivity. Graphene oxide acting as a multi-functional crosslinker between PVA and PNIPA is responsible for the improving strength. Furthermore, this GO-PVA/PNIPA hydrogel with excellent mechanical strength holds a great promise as candidate for temperature sensitive material.

A silo is an important piece of storage equipment, especially in the grain industry. The internal friction angle and the friction coefficient between the grain and the silo wall are the main parameters needed for calculating the lateral pressure of the silo wall. Bamboo is used in silo walls, but there are no provisions about the friction coefficient between bulk grain and bamboo clappers in existing codes. In this paper, the material of the silo wall is bamboo. The internal friction of five types of grain and the friction coefficient between the grain and the bamboo clappers were measured with an equal-strain direct shear apparatus. By comparing the experimental result values with the code values, the friction coefficient between the grain bulk and bamboo clappers is lower than that between grain and steel wall and that between grain and concrete wall. The differences in value are 0.21 and 0.09, respectively.

In this paper, the effect of different buffers, PBS and TBE, on the construction of an aptamer sensor (apt sensor) for ATP was investigated. The apt sensor was based on fluorescence energy resonance transfer (FRET), when the energy donor was 5'-carboxyfluorescein (5'-FAM) and the energy receptor was Au nanoparticles (AuNPs), respectively. Both the donor and acceptor were conjugated with complementary and single stranded DNA (ssDNA). The fluorescent changes of the sensors were measured to investigate the influence of different buffers during the whole preparation and detection process. The results indicated that when the AuNPs and ssDNA (Au-DNA1) were conjugated in PBS buffer, the corresponding apt sensors would obtain a better detection ability of ATP than in TBE buffer.

In order to improve the bending strength of Polystyrene (PS) sintered parts by selective laser sintering, Polystyrene/glass fiber (PS/GF) composite powders were prepared by mechanical mixing method. The size distribution of PS/GF composite powders was characterized by laser particle size analyzer. The optimum ratio of GF was determined by proportioning sintering experiments. The influence of process parameters on the bending strength of PS and PS/GF sintered parts was studied by orthogonal test. The result indicates that the particle size of PS/GF composite powder is mainly distributed in 24.88 μm~139.8 μm. When the content of GF is 10%, it has better strengthen effect. Finally, the article used the optimum parameter of the two materials to sinter prototype, it is found that the PS/GF prototype has the advantages of good accuracy and high strength.

This study focuses on the load and resistance factor design (LRFD) procedure for anisotropic long composite cylinders under external pressure. The theoretical analysis is performed, the performance function is presented, the target reliability levels are determined, the statistical characteristics of random variables are researched and the LRFD-based code is calibrated. The results show the LRFD-based design procedure provides explicit and consistent reliability for long composite cylinder, which could lead less conservative design.

A subsea blowout preventer experimental prototype is developed to meet the requirement of training operators, and the prototype consists of hydraulic control system, electronic control system and small-sized blowout preventer stack. Both the hydraulic control system and the electronic system are dual-mode redundant systems. Each system works independently and is switchable when there are any malfunctions. And it significantly improves the operation reliability of the equipment.

In order to study the dynamic wear evolution of steel wires during multi-axial fretting-fatigue, experiments were carried out on a self-made multi-axial fretting fatigue test rig. The results show that the maximum length, maximum width, area and depth of wear scar will increase with the fatigue cycles, and the cross angle decreases from 11° to 4° with increasing fatigue cycles. The wear coefficient increases quickly at first and then tends to be stabilized when fatigue cycles increases from 5000 to 20000.

It is proposed in the 13th five-year plan that reefs of the south China sea should be constructed. In the paper, an innovative thinking was proposed for the first time in order to realize local material acquisition in island construction and life dependence on sea, namely alkali-resistant glass fibre is mixed in coralaggregate concrete as reinforcing material. The glass fibre is characterized by low price, low hardness, good dispersibility and convenient construction. Reliable guarantee is provided for widely applying the material in future projects. In the paper, an orthogonal test method is firstly applied to determine the mix proportion of grade C50 coral aggregate concrete. Then, the design plan ofmix proportion of alkali-resistant glass fibre enhanced seawater coral aggregate concrete is determined. Finally, the influence law of alkali-resistant glass fibre dosageon tensile compressiveflexture strength of seawatercoralaggregate concrete is made clear.

The conservative operation method which takes unified current-carrying capacity as maximum load current can't make full use of the overall power transmission capacity of the cable. It's not the optimal operation state for the cable cluster. In order to improve the transmission capacity of underground cables in cluster, this paper regards the maximum overall load current as the objective function and the temperature of any cables lower than maximum permissible temperature as constraint condition. The interior point method which is very effective for nonlinear problem is put forward to solve the extreme value of the problem and determine the optimal operating current of each loop. The results show that the optimal solutions obtained with the purposed method is able to increase the total load current about 5%. It greatly improves the economic performance of the cable cluster.

The influence of the reoxidation time on electrical properties and the positive temperature coefficient of resistance (PTCR) effect in multilayer Y₂O₃-doped BaTiO₃ (BTO) ceramics were investigated. The BTO ceramics were sintered at 1160 °C−1270 °C for 2 h in a reducing atmosphere and then reoxidized at 500 °C–900 °C for 0 h−4 h. Results indicated that the room-temperature resistance of BTO ceramics reoxidized at 750 °C for 2 h after sintering at 1160 °C−1270 °C for 2 h decreased with the increasing of the sintering temperature. As the reoxidation time increased, the room-temperature resistance of the BTO samples slightly increased. In addition, the effect of the reoxidation time on the PTCR effect of the ceramics was also studied. The BTO ceramics had a low room-temperature resistance of 0.3 Ω and a resistance jump greater than 3.0 orders of magnitude.

This article demonstrated a technology for producing high purity hexachlorodisilane what is one raw material of Semiconductor industry, which using the method of combination adsorption with rectification, whose material was from polysilicon residues of polysilicon company. This technology could remove most high boiling points chloro-silicane impurities and metal impurities effectively. The purity of Si₂Cl₆ produced by this technology can be up to 99.9%, the content of metal impurities can be low at 4ppb, which can meet the requirement of industy using completely. The technology extends the routes of Si₂Cl₆ in localization, having the advantages of simple process, continuous operation, and large capacity and so on.

We investigate the effect of calcination temperature on the positive temperature coefficient of resistivity (PTCR) characteristics in (Ba_x-0.002Sm0.002)TiO₃ ceramics that were fired at 1250 °C for 30 min in a reducing atmosphere and reoxidized at 800 °C for 1 h in air. The results indicate that the room-temperature resistivity first decreased and then increased as calcination temperature increased from 1000 °C to 1200 °C. Moreover, the critical calcination temperature of 1150 °C is experimentally determined. The samples have a low room-temperature resistivity of 38.4 Ω·cm and exhibit a significant PTCR effect with a resistance jump of 2.1 orders of magnitude. Furthermore, the room-temperature resistivity of the S7 samples doped with a small amount of Mn(NO₃)₂ is much higher than that of the S3 specimens not doped with Mn(NO₃)₂ in our work.

Stretchable electronics, such as stretchable displays and bioeletrictrical interfaces, require stretchable electrical conductors which can be stretched by large strain repeatedly. In this work, highly stretchable indium films were successfully deposited on PDMS substrates using magnetron sputtering. Stretchable indium films can sustain as much as 180% mechanical strain while maintaining great electrical conductivity. Compared to popular gold films, indium films have much better stretchability, light permeability and lower melting point, which can be widely used in bioelectronics.

In order to explore the Lamb wave propagation in laser welding of stainless steel, the numerical simulation is used to show the feature of Lamb wave. In this paper, according to Lamb dispersion equation, excites the Lamb wave on the edge of thin stainless steel plate, and presents the reflection coefficient for quantizing the Lamb wave energy, the results show that the reflection coefficient is increased with the welding width increasing,

New phosphors Sr₃B₂SiO₈: Dy³⁺ have been successfully synthesized via solid-state reaction process. Emission/excitation spectra, photoluminescence decay behaviors were investigated in detail. Under the excitation of 351 nm, the emission spectrum consisting of the characteristic transitions of Dy³⁺ which mainly peaking at 480, 487 nm and 574 nm corresponding to the⁴F_9/2→⁶H_15/2 and⁴F_9/2→⁶H_13/2, respectively, the intensity of the blue emission stronger than the yellow one which indicated that Dy³⁺ ions take the site without inversion symmetry. The chromaticity coordinates of Sr_3-xB₂SiO₈: x Dy³⁺ fixed in the white region. The results showed the kind of phosphor may be act potential applications in the fields of UV-excited white LEDs.

Aiming at the thickness detection of the plate surface attachment, a nondestructive testing method based on the Lamb wave is presented. This method utilizes Lamb wave propagation characteristics of signals in a bi-layer medium to measure the surface attachment plate thickness. Propagation of Lamb wave in bi-layer elastic is modeled and analyzed. The two-dimensional simulation model of electromagnetic ultrasonic plate - scale is established. The simulation is conducted by software COMSOL for simulation analysis under different boiler scale thickness wave form curve. Through this study, the thickness of the attached material can be judged by analyzing the characteristics of the received signal when the thickness of the surface of the plate is measured.

In this paper, diamond single crystal co-doped with sulfur and boron was successfully synthesized at the fixed pressure of 6.0 GPa and temperature range of 1535 K. Sulfur was detected in the co-doped diamond by Fourier Transform Infrared Spectroscopy (FTIR) and the corresponding characteristic peak located at 848 cm-1. Interestingly, Hall effect measurements indicated that the diamond co-doped with sulfur and boron exhibited n-type semiconductor behaviour. Furthermore, the Hall mobility and carrier concentration of the co-doped diamond higher than those of the boron-doping diamond.

Penetrating the shell armor is an effective means of destroying hard targets with multiple layers of protection. The penetration process is a high-speed impact dynamics research category, involving high pressure, high temperature, high speed and internal material damage, including plugging, penetration, spalling, caving, splashing and other complex forms, therefore, Analysis is one of the difficulties in the study of impact dynamics. In this paper, the Lagrang algorithm and the SPH algorithm are used to analyze the penetrating steel plate, and the penetration model of the rocket penetrating the steel plate, the failure mode of the steel plate and the missile and the advantages and disadvantages of Lagrang algorithm and SPH algorithm in the simulation of high-speed collision problem are analyzed and compared, which provides a reference for the study of simulation collision problem.

In this paper, rolling bearing fault diagnosis method is proposed based on wavelet packet threshold de-noising and improved BP neural network. It achieves the goal of signal de-noising by setting the appropriate threshold, and then the denoised signal is decomposed into three layers by wavelet packet. The energy characteristics of the 8 frequency bands are calculated respectively. Levenberg-Maquardt algorithm which is improved the traditional BP neural network to improve the diagnosis efficiency of BP neural network, is proposed. Taking the outer ring fault of rolling bearings as an example, the experimental results show that the wavelet packet threshold de-noising can effectively improve the signal-to-noise ratio. Compared with the traditional BP neural network, the improved BP neural network has better diagnosis efficiency.

In this paper, by testing welding joints of their metallography and hardness, we analyze the metal structure. And then, the microstructure characteristics, macro and micro fracture morphology of underwater welding joint were investigated by means of metallographical examination and SEM. The fracture failure of the underwater welding joint is discussed here. The cracks are the major factors to fracture failure. The cracks spread along with the crack of the welding line, and this expand process generates dimple. The crack continues to expand under the action of tensile and the fracture fails eventually.

In this paper, a design method of detachable intelligent platform trolley is presented. The detachable intelligent platform trolley has three driving modes, and the rubber blanket and the cardan joint in the structure filter effectively the road surface turbulence and improve the safety of the driver. The design idea of the active wheel fixed structure and the driven steering wheel structure is emphatically introduced. At last, The results show that the right panel of intelligent platform trolley as the research object and analyses the load, static stress of the right panel of platform trolley mainly concentrated in the panel at the front and back ends and other connectors on the contact surface. In addition, the safety factor can meet the design requirements by analysis.

The thermal protective performance of the fire fighter protective clothing is of vital importance for fire fighters. In the study fabrics treated by phase change materials (PCMs) were applied in the multi-layered fabrics of the fire fighter protective clothing ensemble. The PCM fabrics were placed at the different layers of the clothing and their thermal protective performance were measured by a TPP tester. Results show that with the application of the PCM fabrics the thermal protection of the multi-layered fabrics was greatly increased. The time to reach a second degree burn was largely reduced. The location of the PCM fabrics at the different layers did not affect much on the thermal protective performance. The higher amount of the PCM adds on, the higher thermal protection was brought. The fabrics with PCMs of a higher melting temperature could contribute to higher thermal protection.

According to the growing demand for air transport industry, an extension of the associated taxiway is required, so the Shenzhen Airport runway west of the taxiway expansion is imperative. Combined with the taxiway of Shenzhen Baoan International Airport, we design the lower layer type of AC-25 modified asphalt mixture ratio. We analysis from raw material selection, mixture gradation design and admixture added, and finally choose the excellent performance of asphalt mixture.

Conducting sand liquefaction estimated based on codes is the important content of the geotechnical design. However, the result, sometimes, fails to conform to the practical earthquake damages. Based on the damage of Tangshan earthquake and engineering geological conditions, three typical sites are chosen. Moreover, the sand liquefaction probability was evaluated on the three sites by using the method in the Code for Seismic Design of Buildings and the results were compared with the sand liquefaction phenomenon in the earthquake. The result shows that the difference between sand liquefaction estimated based on codes and the practical earthquake damage is mainly attributed to the following two aspects: The primary reasons include disparity between seismic fortification intensity and practical seismic oscillation, changes of groundwater level, thickness of overlying non-liquefied soil layer, local site effect and personal error. Meanwhile, although the judgment methods in the codes exhibit certain universality, they are another reason causing the above difference due to the limitation of basic data and the qualitative anomaly of the judgment formulas.

Aiming at the problem that the existing detection method can not effectively solve the security of UAV's ultra low altitude flight caused by power line, a power line recognition method based on grid search (GS) and the principal component analysis and support vector machine (PCA-SVM) is proposed. Firstly, the candidate line of Hough transform is reduced by PCA, and the main feature of candidate line is extracted. Then, upport vector machine (SVM is) optimized by grid search method (GS). Finally, using support vector machine classifier optimized parameters to classify the candidate line. MATLAB simulation results show that this method can effectively identify the power line and noise, and has high recognition accuracy and algorithm efficiency.

Intelligent home as a way to achieve the realization of the family information has become an important part of the development of social information, Internet of Things because of its huge application prospects, will be smart home industry in the development process of a more realistic breakthrough in the smart home industry development has great significance. This article is based on easy to implement, easy to operate, close to the use of the design concept, the use of STC89C52 microcontroller as the control core for the control terminal, and including infrared remote control, buttons, Web interface, including multiple control sources to control household appliances. The second chapter of this paper describes the design of the hardware and software part of the specific implementation, the fifth chapter is based on the design of a good function to build a specific example of the environment.

With the continuous progress of society, the continuous development of the times, people's living standards continue to improve, people continue to improve the pursuit. With the rapid development of automobile manufacturing, the car will be all over the tens of thousands of households, the increase in car traffic, a direct result of the incidence of traffic accidents. Brake system is the guarantee of the safety of the car, its technical condition is good or bad, directly affect the operational safety and transportation efficiency, so the brake system is absolutely reliable. The requirements of the car on the braking system is to have a certain braking force to ensure reliable work in all cases, light and flexible operation. Normal braking should be good performance, in addition to a foot sensitive, the emergency brake four rounds can not be too long, not partial, not ring.

Elliptical vibration cutting (EVC) has been widely concerned since it was proposed, and its unique characteristics such as friction reversal and intermittent cutting can effectively extend the tool life, improve the machined surface roughness and so on. The objective of this paper was to predict the behavior of cutting force. A method of predicting the behavior of cutting force based on the chip thickness under various cutting conditions is proposed. Based on the established tool motion model, the chip model was founded. By numerical simulation, the effects of cutting parameters on cutting force under various cutting conditions were studied. The results show that the chip thickness can be used to predict the behavior of cutting force.

Micro-displacement motion stage driven by piezoelectric actuator has a significant demand in the field of ultra-precision machining in recent years, while the design of micro-displacement motion stage plays an important role to realize a large displacement output and high precision control. Thus, a 3D elliptical micro-displacement motion stage driven by three PZT actuators has been developed. Firstly, the 3D elliptical trajectory of this motion stage could be adjusted through the form of the PZT actuators input signal. Then, the desired trajectory was obtained by adjusting the micro displacement of the motion stage in 3D elliptical space. Finally, the trajectory simulation and the finite element simulation were applied in this motion stage. The experimental results shown that, the output displacement of the three directions under the input force of the 1600N were 14μm, 16μm and 74μm, respectively. And the first three modes were 1471.6Hz, 2698.4Hz and 2803.4Hz, respectively. Analysis and experiments were carried out to verify the performance, result proved that a large output displacement and high precision control could be obtained.

The use of recycled aggregate as replacement of natural aggregate has increased in recent years in order to reduce the high consumption of natural resources in construction industry. This paper presents an experimental investigation on the effect of graphene oxide (GO) on the mechanical properties of recycled mortar. It is showed that the recycled mortar with GO has a better mechanical properties than the recycled mortar without GO. Microstructural analysis of the recycled mortar with GO showed to have much denser and better crystallization of hydration product.

In this paper, Zn₃V₂O₈ phosphors were synthesized by high temperature solid method. The effect of flux on the luminescent properties was studied. And based on the first-principles planar wave super-soft pseudo potential method of density functional theory (DFT), the α- Zn₃V₂O₈ crystal model was used to calculate the electronic structure and optical properties of the model. The results show that the crystal morphology of the sample is improved, the grain agglomeration is reduced and the crystal structure isn't changed. The excitation spectrum ranges from 300-400nm, the excitation peak is at 360nm, and the emission spectrum is in the range of 420-690 nm, the peak at 550 nm. α- Zn₃V₂O₈ is an indirect band gap, α- Zn₃V₂O₈ has a band gap of 2.715eV, α- Zn₃V₂O₈ has a strong UV-near ultraviolet light absorption capacity.

In this paper, we mainly introduce a multi-function water temperature controller designed with 51 single-chip microcomputer. This controller has automatic and manual water, set the water temperature, real-time display of water and temperature and alarm function, and has a simple structure, high reliability, low cost. The current water temperature controller on the market basically use bimetal temperature control, temperature control accuracy is low, poor reliability, a single function. With the development of microelectronics technology, monolithic microprocessor function is increasing, the price is low, in all aspects of widely used. In the water temperature controller in the application of single-chip, with a simple design, high reliability, easy to expand the advantages of the function. Is based on the appeal background, so this paper focuses on the temperature controller in the intelligent control of the discussion.

Commercial AZ91 Mg alloys were equal channel angular pressed (ECAP) for up to 6 passes at temperature as low as 473K. Microstructures and mechanical properties of as-received and as-pressed samples were investigated. It is shown that ECAP applied successfully to these materials at elevated temperatures leads to grain refinement due to the occurrence of recrystallization during the pressing process and to significant improvements in the strength and ductility of these materials. The microstructure was obviously refined and the average grain size was considerably reduced from over 28μm to below 1μm. From tensile testing at room temperature (RT), the ultimate tensile strength (UTS) increases obviously from 318MPa to 365MPa, in contrast, the uniform elongation increased from 12% of the as-received to 26% of the pressed up to 4 passes. These observations may be attributed to the effects combined grain refinement and texture development.

A new design of bipolar plate flow field in proton exchange membrane (PEM) stack was presented to develop a high-performance transfer efficiency of the two-phase flow. Two different flow fields were studied by using numerical simulations and the performance of the flow fields was presented. the hydrodynamic properties include pressure gap between inlet and outlet, the Reynold's number of the two types were compared based on the Navier–Stokes equations. Computer aided optimization software was implemented in the design of experiments of the preferable flow field. The design of experiments (DOE) for the favorable concept was carried out to study the hydrodynamic properties when changing the design parameters of the bipolar plate.

The quality of withhold parts determines the service life of high-pressure rubber hose to a great extent. Leakage at withholding is the main form of high pressure hose failure in the several forms. The quickest and most effective method to detect the withholding quality is measuring the section size of the withhold parts. As long as the section size is in line with the provisions, that is, the quality of hose withholding is qualified. In this paper, the mesurement system which is designed improves low efficiency of manual mesurement.

The finite element simulation is an effective way for the study of thin-walled tube in the two cross rolls straightening process. To determine the accurate radius of curvature of the roll profile more efficiently, a simplified finite element model based on the technical parameters of an actual two cross roll straightening machine, was developed to simulate the complex straightening process. Then a dynamic simulation was carried out using ANSYS LS-DYNA program. The result implied that the simplified finite element model was reasonable for simulate the two cross rolls straightening process, and can be obtained the radius of curvature of the roll profile with the tube's straightness 2 mm/m.

The core section of Guiyang Nanming River suffers from river water quality deterioration, black turbidity, sediment deposition and other phenomena. The deposition is extremely serious particularly at the upstream area in front of the flap dam. It is necessary to upgrade and transform the flap dam, thereby preventing the sedimentation in the front of the dam, and improving the ecological environment of the river. The flap dam should be newly designed, and its application should be studied.

A brief introduction of the development background, the concept, characteristic and advantages of lithium-ion battery was given. The typical fire accidents about lithium-ion battery in production process, the vehicle with new energy, portable electronic products were summarized. Some important factors for lithium-ion batteries' safety were emphatically analyzed. Several constructive suggestions on improvement direction were given, meanwhile, we have a nice exception on the future of lithium-ion battery industry.

In this paper, CaCO₃, CoO, CuO as raw materials, using solid phase preparation of Ca₃Co₄O₉-based thermoelectric materials doping Cu. The Ca₃Co₄O₉-based thermoelectric material intermediates were prepared according to the stoichiometric ratio x=0.01, and the sintered crystals were prepared by using muffle furnace under different temperature setting conditions. X-ray diffraction (XRD) and Scanning electron microscopy (SEM) were used to analyze the crystallinity and morphology of the samples after sintering. The results show that the crystallinity of Ca₃Co₄O₉-based thermoelectric materials is best when sintered at 800-850°C, and the crystallinity of samples sintered at 850°C is better than that at 800°C, The diffraction intensity ratio is stronger than 800°C. Continue to raise the temperature, Ca₃Co₄O₉-based thermoelectric materials phase transition to Ca₃Co₂O₆-based thermoelectric materials, When the sintering temperature is 1000°C, the product is Cu-doped Ca₃Co₂O₆-based thermoelectric materials.

Pure TiO₂ and N-doped nano-TiO₂ photo catalysts were individually prepared following the sol-gel method under ultrasonic conditions. The photo catalytic decomposition of methyl orange (MO) solution under ultraviolet and visible light irradiation was used as a probe reaction to estimate their photo catalytic activities. The particle size, crystal structure, and optical properties of the prepared TiO₂ were performed by X-ray diffraction, transmission electron microscopy and UV–vis diffuse reflectance spectroscopy. The results suggest that ultrasound significantly reduced the size of the TiO₂ particles, improved particle dispersion, which in turn improve the photo catalytic activity of TiO₂ under ultraviolet light. Ultrasound also promoted the doping of non-metal nitrogen and markedly enhanced the visible light absorption capacity of the N-doped nano-TiO₂. Compared with pure TiO₂, the degradation rate for MO under visible light of U-N-TiO₂ was increased by 70%.

The conception and compose of emergency plan system is introduced and the emergency disposal principle, measure and procedure of videoconference system is detailed stated. It will benefit the construction of emergency response plan system

The object of this study was to investigate the impact of application biocar on peanuts growing. It was based on a long-term fertilization experiment which researched the effect of applying different amounts of biochar and BBF when continuously cropping peanuts for 5 years. There were five treatments: no fertilizer, low level of biochar (C15), high level of biochar (C50), chemical nitrogen–phosphorus–potassium (NPK) fertilizer and biochar-based fertilization (BBF).We determined peanuts stem and leaf weight, root weight, plant and the relative content of chlorophyll at every growth stages in 2016. The results showed that all fertilization can increase these indexes and in application of NPK improve them the most which close to BBF. The peanuts stem and leaf weight, root weight, plant and the relative content of chlorophyll was higher than the same level carbon treatment (C15) 62.85%, 6.67%, 18.73% and 25.58%, respectively. Expect stem and leaf weight, plant height, root weight and chlorophyll were higher when high level biochar (C50) applied than the low one (C15).

A kind of hexagonal ZnO (HZO) was synthesized in N-methyl-2-pyrrolidone (NMP)/H2O mixed solvent for a high exposure of polar ±(0001) facets to get a high-efficiency photocatalyst. The amine-functionalized HZO particles were coated with graphene oxide (GO) by electrostatic force-induced self-assemby and thermal reduction to form HZO@Gr core/shell structure. The as-prepared HZO and HZO@Gr were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy and UV-visible diffuse reflectance spectroscopy (UV-vis/DRS). The results indicate that the graphene on HZO@Gr remains high quality and the optical properties of the composite change a lot with sunlight absorption improving, bandgap and photoluminescence (PL) intensity decreasing. The obtained HZO photocatalyst shows good photocatalytic activity for methylene blue (MB) under UV-visible irradiation. Furthermore, the HZO@Gr photocatalyst exhibits the best photodegradation rate of MB reaching up to 98.2% within 50 minutes. The graphene-coated HZO structure could offer new directions which would further extend the scope for synthesis of various ZnO/graphene composites with improved properties useful for various applications.

In order to study the efficacy of calcium carbonate for cobalt (Co) fixation, as well as its influence on chemical speciation of Co in fluvo-aquic soil, pakchoies were planted in the soil with different quantities of exogenous Co and calcium carbonate. Co concentrations in the mature plant shoots were analyzed, and the chemical speciation of Co were detected with the Tessier five-step sequential extraction. The results showed that the Co concentration in plants tended to decrease first and then get higher with the concentration of calcium carbonate increasing (0-12g/kg) in soil (P < 0.05). The proportion of Co in the exchangeable form in the soil followed the similar tendency (P < 0.05), which might transform from the exchangeable form into the carbonate-associated and organic-associated forms. A regression analysis showed that when the concentrations of calcium carbonate were in the range of 5.0 to 7.5 g/kg, Co concentration in the plant reached to the lowest point, while the proportion of Co in the exchangeable form reached the minimum. In conclusion, to get the optimum effect, the dosage of calcium carbonate should be kept in the range of 5.0 to 7.5 g/kg when it is applied to Co fixation.

The peel strength of polyvinyl chloride (PVC) edge band on curved edge part was tested by using experimental method which was conducted to define the influence of many factors, including temperature of applying glue, glue dosage and feed rate on peel strength of edge band from curved edge part. The results showed that the temperature of applying glue, glue dosage and feed rate have a great effect on the peel strength of PVC edge band. The obtained optimum technical parameters were respectively as follow: temperature of applying glue was 140~150°C, glue dosage was 363~379g/m2 and feed rate was 13~15m/min.

Shield method construction of coal mine roadway is the future trend of the development of deep coal mining. The main shaft supporting is the segment. There is rubber pads between segment and segment. The performance of compression deformation of rubber pad is essential for the overall stability of lining. Through load test, displacement of the rubber pad under load, the thrust force law of the rubber pad deformation, and provide a theoretical basis for the stability analysis of coal mine tunnel shield construction.

A novel donor-acceptor type conjugated polymer PTBFTPD based on two-dimensional (2D) conjugated alkylthienyl substituted thieno[2,3-f]benzofuran (TBF) and thienopyrroledione (TPD) unit, was synthesized and applied as donor material for bulk heterojunction solar cells. The novol polymer possesses a narrow bandgap of 1.83 eV, a deep HOMO energy level (-5.64 eV) and a closer π−π stacking. After conventional devices were fabricated using PTBFTPD as donor blending with PC₇₀BM as acceptor, a power conversion efficiency (PCE) of 4.33% with a high open circuit voltage (V_oc) of 1.09 V was obtained. The result indicates the promising potential of thieno [2, 3-f] benzofuran unit for high efficient polymer solar cells with a high voltage.

The precursors of Mn₂O₃ was synthesized through co-precipitation method using MnAc_2·4H₂O, NaHCO₃ as raw materials. The precursors were heat-treated at 400°C, 500°C, and 600°C, respectively. The samples were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical properties of the samples were investigated also. The test results showed that the Mn₂O₃ (heat-treated at and 600°C) featured higher reversible capacity and better cycling performance than that of other samples. The specific capacity of the Mn2O3 samples (heat-treated at and 600°C) was 745 mAh/g respectively after 100 cycles at a constant current of 100 mA/g in the voltage range of 0.01-3 V. The preparation principle for the formation of the Mn2O3 samples and its electrochemical process of Mn₂O₃ were discussed also.

The NiMoO₄ samples were synthesized by rheological phase-hydrothermal method. The efforts of different annealed temperatures on the morphologies and electrochemical properties of the final products were systematically investigated. The NiMoO₄ samples exhibit the best electrochemical properties with a high reversible capability (640 mAh g⁻¹ at current density of 50 mA g⁻¹) and cycling stability, compared with the other samples. These results indicate that the NiMoO₄ samples could be promising electrode materials for lithium ion batteries.

The synergistic reaction under specific conditions of the nonlinear system, weak driving signal and moderate noise can make noise to be advantageous in a certain extent, so as to achieve the purpose of signal enhancement, this seemingly anomalous phenomenon is defined as stochastic resonance. In this paper, the weak signal detection under strong noise background is the main line. The principle of white noise to counteract external noise is expounded, and the present research situation and development trend of stochastic resonance are reviewed in that paper, it also pointed out the direction of further research of stochastic resonance technology.

Considering the characteristic of radar, constructed the evaluation index system of radar importance, established the comprehensive evaluation model based on decision matrix. Finally, by means of an example, the methods of this evaluation on radar importance was right and feasibility.

In this paper, double cross-linked gel system was first screened. Organic chromium cross-linking agent was selected as primary cross-linking gel system, hyperbranched polyacrylamide as primary cross-linking system main polymer, phenolic resin system as a cross-linking agent for secondary cross-linked gel system, cationic polyacrylamide as a cross-linking agent for secondary cross-linked gel systems. Through the experiment, the formula of the double cross-linked gel system was that the amount of fixed hyperbranched polyacrylamide was 2000mg/L, the amount of internal network cross-linking agent was 300mg/L, the amount of stabilizer was 800mg/L, the amount of cationic polyacrylamide was 2000mg/L, the amount of enhancer was 150mg/L and the system performance was evaluated.

The concentrated seawater containing abundant salt components can be utilized as water resource in soda industry either to lower the production cost or prevent the environmental problems caused by excessive drainage. However, its application has been confined by the high contents of the scaling ions (Ca2+, Mg2+, SO42-) which probably cause production interruption and unnecessary energy consuming. Hence, this study has developed a process for concentrated seawater refining by the waste liquid from the soda production and investigated its optimum conditions: Ca(OH)2/Mg2+=1.0, pH ≥ 10.61, proportion of demonization waste liquid adding to 40%v/v, 10% w/v seed crystal input, and Ca2+/CO32-=1.1. The composition of refined liquid could satisfy the requirement of actual production.

Laser cladding technology has a high demand for control system, and the domestic laser cladding control system mostly uses the traditional PID control algorithm. Therefore, the laser cladding control system has a lot of room for improvement. This feature is suitable for laser cladding technology, Based on fuzzy PID three closed-loop control system, and compared with the conventional PID; At the same time, the laser cladding experiment and friction and wear experiment were carried out under the premise of ensuring the reasonable control system. Experiments show that compared with the conventional PID algorithm in fuzzy the PID algorithm under the surface of the cladding layer is more smooth, the surface roughness increases, and the wear resistance of the cladding layer is also enhanced.