Batteries and Energy Storage
A495
Yoojung Kim and Jaephil Cho
A500
N. D. Leifer, A. Colon, K. Martocci, S. G. Greenbaum, F. M. Alamgir, T. B. Reddy, N. R. Gleason, R. A. Leising and E. S. Takeuchi
A507
F. Leardini, J. F. Fernández and F. Cuevas
A515
Yong Min Lee, Jun Young Lee, Heung-Taek Shim, Joong Kee Lee and Jung-Ki Park
The morphological and compositional changes of the solid electrolyte interphase (SEI) layer formed on the surface of Si thin electrodes during precycling were investigated. At the beginning of charging, the native layer (
and silanol) covering the surface of the Si thin electrode is readily destroyed and a new SEI layer is formed by the decomposition of both organic solvents and anions. At this stage, the interfacial resistance decreases to a minimum level. Thereafter, the interfacial resistance increases with charging due to the growth of an SEI layer, which is mainly originated from the decomposition of organic solvents. During the discharging process, an SEI layer was formed mainly by the decomposition of anions.
A520
B.-C. Park, H. J. Bang, C. S. Yoon, S.-T. Myung, J. Prakash and Y.-K. Sun
A527
Chi-Wi Ong, Yuan-Kai Lin and Jenn-Shing Chen
A534
Aniruddha Deb, Uwe Bergmann, Stephen P. Cramer and Elton J. Cairns
After the recent upsurge of interest in the layered
system for use as a cathode material for rechargeable lithium batteries, we have studied the charge compensation mechanism and structural perturbations occurring during cycling of the novel layered system of
coated with nano-crystallized
, which effectively improved the rate capability. In addition, the
evidently suppressed any structural change of the
. In situ X-ray absorption spectroscopy (XAS) measurements were performed utilizing a novel in situ electrochemical cell, specifically designed for long-term X-ray experiments. The cell was cycled at a moderate rate through a typical Li-ion battery operating voltage range
. The electrode contained
of
on a
Al foil, and had an area of
. XAS measurements were performed at different states of charge (SOC) during cycling, at the Ni, Co, and the Mn edges, revealing details about the response of the cathode to Li insertion and extraction processes. Extended X-ray absorption fine structure region of the spectra revealed the changes of bond distance and coordination number of Ni, Co, and Mn absorbers as a function of the SOC of the material. We found that the oxidation states of the transition metals in the system are
,
, and
in the fully discharged condition. During charging the
is oxidized to
through an intermediate stage of
,
is oxidized almost to
. Utilizing a combination of Faraday’s calculation and XAS results, the Co was found to be at
at the end of the charge, whereas Mn was found to be electrochemically inactive and remains as
. These measurements on this cathode material confirmed that the material retains its symmetry and good structural short-range order leading to superior cycling.
A542
Jinyoung Kim and Jaephil Cho
A547
D. Golodnitsky, R. Kovarsky, H. Mazor, Yu. Rosenberg, I. Lapides, E. Peled, W. Wieczorek, A. Plewa, M. Siekierski, M. Kalita et al
The complex interplay between the ionic conductivity and structure of the
polymer electrolyte, induced by the calix[6]pyrrole anion receptor, has been investigated by different experimental methods, including ac impedance, calorimetry, X-ray diffraction, and Fourier-transform infrared spectroscopy. It was found that calix[6]pyrrole, even at low concentrations, can form stable bidentate complexes with triflate anions, thus making cation transport dominating, which results in
close to unity. It should be noted that the incorporation of an anion trap does not suppress the bulk ionic conductivity of polymer electrolytes at above 60°C. We attribute this effect to the dissociation of ion aggregates and structural changes imposed by the additive. Stable solid electrolyte interface resistance was achieved in the polymer electrolytes containing calix[6]pyrrole.
A554
A. Turković, M. Pavlović, P. Dubček, M. Lučić-Lavčević, B. Etlinger and S. Bernstorff
A561
Yoojung Kim, Junho Eom, Min Gyu Kim, Yang-Kook Sun, Chong Seung Yoon and Jaephil Cho
A566
Naoaki Yabuuchi, Sundeep Kumar, Hayley H. Li, Yong-Tae Kim and Yang Shao-Horn
A579
Fernando Pico, Carlos Pecharroman, Alejandro Ansón, M. Teresa Martínez and Jose M. Rojo
A587
Qi Zhang and Ralph E. White
A597
A. D. W. Todd, R. E. Mar and J. R. Dahn
Fuel Cells and Energy Conversion
B501
Brian D. Madsen and Scott A. Barnett
Solid oxide fuel cells (SOFCs) were fabricated with thick
(GDC) electrolytes, composite anodes containing
(LSCV), GDC, and
, and Au current collector grids. SOFCs with varying anode firing temperatures, GDC contents, and
contents were structurally evaluated and characterized by current-voltage measurements and electrochemical impedance spectroscopy in humidified hydrogen and air. With increasing anode firing temperature, particle sizes in the porous anodes increased and the area specific resistance
increased (power density decreased). For lower firing temperatures, e.g., 1100°C,
decreased sharply with increasing
content from 0 to
, but showed little further decrease from 5 to 
.
values were generally higher for higher firing temperatures, e.g., 1400°C, decreasing gradually with increasing
content from 0 to
. These trends were explained by an increase in Ni particle sizes with increasing firing temperature, making the Ni catalyst less effective. The anode polarization resistance at 750°C was
at
cell voltage (
at open circuit), for a composition of
LSCV,
GDC, and 
.
B508
Monica Lira-Cantu, Kion Norrman, Jens W. Andreasen, Nieves Casan-Pastor and Frederik C. Krebs
B514
Fuqiang Liu and Chao-Yang Wang
A mathematical model for the cathode of a direct methanol fuel cell (DMFC) is developed to investigate two-phase transport in the catalyst layer (CL) and to elucidate the mechanism of cathode mixed potential due to oxidation of crossover methanol. A coupled model of two-phase species transport and multistep electrochemical kinetics, including simultaneous oxygen reduction, methanol oxidation, and gas phase chemical reaction, is presented. The model predictions agree favorably with experiments of cathode mixed potential, and the predicted profiles of water saturation, oxygen concentration, and overpotential along the CL thickness further reveal the profound interplay between multiple reactions and the transport of oxygen and water. It is shown that in the presence of methanol crossover, the DMFC cathode is operated at higher overpotential and water saturation, with larger oxygen transport loss than that in the
/air counterpart. The model results also indicate that reducing the cathode CL thickness can facilitate both liquid water removal and oxygen transport through the CL, leading to improved cathode performance.
B523
Zhengrong Xu, Jingli Luo and Karl T. Chuang
B528
Fu-Chi Wu, Chi-Chao Wan, Yung-Yun Wang, Li-Duan Tsai and Kan-Ling Hsueh
Better catalyst utilization is essential to improve cell performance and to reduce catalyst loading of polymer electrolyte fuel cells. The current function of perfluorosulfonic ionomer (PFSI) in the catalyst paste is to serve as an ionic conducting agent and binder in the catalyst layer. In this study, we have successfully used the PFSI to stabilize dispersed Pt particles in addition to its original function as ionic conducting agent and binder. This results in an electrode with fine Pt cluster, high ionic conductivity, and high catalyst utilization. Silane coupling agent 3-aminopropyltrimethoxysilane (APTMS) was employed to graft PFSI on Pt surface resulting in significant steric stabilization. Electron spectroscopy for chemical analysis and nuclear magnetic resonance results had been verified the occurring of coupling reaction. The transmission electron spectroscopy/energy-dispersive spectroscopy image showed the PFSI indeed grafted on the Pt surface. The primary particle of Pt was
, which was examined by extended X-ray absorption fine structure. The cell performances of the membrane electrode assembly (MEA) made with APTMS-modified Pt cathode and the MEA without treatment were compared. About 15% utilization increase can be achieved by the APTMS treatment.
B533
H. Chhina, S. Campbell and O. Kesler
B540
Anil V. Virkar and Yingke Zhou
A mechanism of catalyst particle growth in proton exchange membrane fuel cells (PEMFCs) by Ostwald ripening is presented. Particle growth occurs as a coupled process involving platinum ion transport through aqueous liquid and/or ionomer, and electron transport through a carbon support. The dominating factor in degradation of a catalyst supported on carbon is the presence of platinum ions in solution (in liquid and/or in ionomer). Experiments were conducted on commercial PEMFC electrodes in three liquids,
solution, dilute acid solution, and deionized water. Pt particle size grew from
to
after
in
solution. By contrast, no detectable growth occurred in dilute acid or in deionized water. This demonstrates that the higher the Pt ion concentration, the faster the kinetics. The role of electronic conduction through support was verified by conducting experiments in
solution on Pt supported on an electronically insulating material, namely alumina. While significant growth occurred in Pt supported on carbon, no detectable growth occurred in Pt supported on alumina. This observation is in complete accord with the model, and demonstrates the role of electronic transport on degradation. That is, when supported on alumina, lack of an electronically conducting path suppresses degradation even with
present in solution.
B548
Wolfgang G. Bessler and Stefan Gewies
This series of papers presents details of numerical studies of the nature of the impedance of solid oxide fuel cell (SOFC) anodes caused by gas-phase transport processes. The present part treats channel geometries where gases are transported parallel to the electrode surface. Two cases are investigated: (i) channel flow by forced convection, a typical situation in planar stack segments; and (ii) channel diffusion without convective flow, a typical situation in laboratory-scale single-chamber experiments using symmetrical cells. Current/voltage curves and electrochemical impedance spectra are simulated based on the Navier–Stokes transport equations and nonlinear electrochemistry models. Both channel flow and channel diffusion cause a capacitive behavior in the form of an resistance-capacitive (RC)-type semicircle in the Nyquist diagram. Its resistance and relaxation frequency strongly depend on operation parameters (gas concentration, flow rate, temperature, electrochemical polarization) and geometry (channel length and cross-sectional area). The model predictions are in good quantitative agreement with four different experimental studies published in the literature. The simulation approach thus allows a physically based assignment of observed gas concentration impedance processes.
B560
Yanming Gong, Yaw D. Yeboah, Serguei N. Lvov, Victor Balashov and Zhicheng Wang
B566
D. A. Stevens, J. M. Rouleau, R. E. Mar, A. Bonakdarpour, R. T. Atanasoski, A. K. Schmoeckel, M. K. Debe and J. R. Dahn

random alloy samples, covering most of the binary composition range, have been prepared via magnetron sputtering. The alloys were deposited through shadow masks onto 3M nanostructured thin-film catalyst support for testing in a 64-electrode polymer electron membrane fuel cell (PEMFC). CO stripping voltammograms and hydrogen oxidation polarization curves with pure hydrogen and with reformate containing up to
CO were measured on all the samples. In agreement with reports in the literature, Ru, Mo, and Sn were found to improve the CO tolerance of Pt, although the intrinsic hydrogen oxidation activity of Pt decreased significantly as the Sn content increased. The addition of Co to Pt had no impact on CO tolerance, possibly because of loss of surface Co through dissolution in the fuel cell. The addition of Au to Pt led to an increase in hydrogen oxidation overpotential when CO was present. Small amounts of Ta gave a small reduction in hydrogen oxidation overpotential in the presence of CO, but the overpotentials were still too high for practical application in a reformate-fed fuel cell.
B577
Lan Zhang, San Ping Jiang, Chia Siang Cheng and Yujun Zhang
B583
E. Ruiz-Trejo and J. Maier
B588
Mingliang Liu, Zhe Lü, Bo Wei, Ruibin Zhu, Xiqiang Huang, Kongfa Chen, Gang Ai and Wenhui Su
B593
Gyoung-Ja Lee and Su-Il Pyun
Ion penetration into pores during double-layer charging/discharging has been investigated by analyses of potentiostatic current transients (PCTs) and cyclic voltammograms (CVs) experimentally measured on porous carbon electrodes with pore fractality. From the analyses of the cathodic PCTs measured on microporous electrodes, it was found that the PCTs showed ideal behavior with a slope of
in the earlier stage, indicating that the change in the resistance-capacitance (RC) time constant distribution produced by pore fractal dimension in the micropore size range is too small to affect the shape and value of the PCT. The cathodic PCTs measured on meso/macroporous electrodes exhibited anomalous behavior with a slope lower than
in the earlier stage due to the considerably wider RC time constant distribution. From the analyses of the cathodic PCTs measured on multifractal electrodes, it is strongly suggested that the current decays more rapidly with increasing relative volume fraction of larger-sized pores. From the analyses of the measured CVs, it is experimentally confirmed that the higher relative volume fraction of larger-sized pores enhances the rate capability γ, which yields us the higher power density, but it reduces the double-layer capacitance, which provides us the lower energy density.
B601
A. Flügel, M. D. Dolan, A. K. Varshneya, Y. Zheng, N. Coleman, M. Hall, D. Earl and S. T. Misture
Corrosion, Passivation, and Anodic Films
C279
E. Matykina, F. Monfort, A. Berkani, P. Skeldon, G. E. Thompson and J. Gough
The local compositions, structures, and morphologies of titania-based coatings formed by spark anodizing of titanium have been investigated using analytical scanning and transmission electron microscopies. The coatings were formed at 20, 40, or
in orthophosphate and pyrophosphate electrolytes at
, which are relevant to development of osseointegrated implants. According to X-ray diffraction, anatase and rutile are the main crystalline phases in the coatings, with amorphous material also being present, as confirmed by transmission electron microscopy. The amorphous phase is more extensive for formation in the pyrophosphate electrolyte than in the orthophosphate electrolyte and contains high levels of phosphorus species relative to that in adjacent nanocrystalline regions. Porosity, extending from craters at the coating surface to the vicinity of the metal/coating interface, is revealed in coating taper sections. Finer, submicrometer porosity is also found in some coating regions. Locations of silicon tracer species indicate destruction of coating material at breakdown sites followed by regrowth of material at the damaged regions.
C286
J. Idrac, Ch. Blanc, Y. Kihn, M. C. Lafont, G. Mankowski, P. Skeldon and G. E. Thompson
Model alloys, generated by magnetron sputtering, have been employed to understand the role of copper on the corrosion behavior of aluminum alloys. Binary Al–Cu alloys, with copper contents between 0 and 100 atom %, were synthesized with well-controlled compositions, embracing single-phase α and θ alloys together with multiphase alloys. Electrochemical measurements confirmed the stability of the thin alloy films and revealed that the corrosion behavior of the α, θ, and
phases differed strongly in the cathodic region. Further, in the anodic region, phases of high copper content suffered pitting in sulfate solutions, while the α phase remained passive.
C294
Jin Kawakita, Martin Stratmann and Achim Walter Hassel
In an attempt to improve the corrosion resistance of a NiTi shape memory alloy, thick oxide films were fabricated on the surface by an anodic oxidation process. High-voltage square shape pulse anodization was carried out in various electrolytes over the whole range of pH values from sulfuric acid, acetate buffer, ammonium pentaborate, sodium diphospho heptoxide, sodium aluminate, and potassium hydroxide. Microscopic observation showed that the films are porous or tile structured in nature and the structural analyses by X-ray diffraction and Raman spectroscopy demonstrated their amorphous nature. From the chemical analyses, the oxide films were determined to consist mainly of titanium as the metal component, whereas the nickel content of the oxide films depends on the pH value of the electrolyte as well as the amount of anions incorporated from the electrolyte. The application of an asymmetrical rectangle waveform was effective in increasing the density of the films. An electrochemical technique was used for screening the corrosion resistance of the anodized films and demonstrating the improvement in the resistance against localized corrosion of NiTi.
C299
Gonzalo Viramontes-Gamboa, Berny F. Rivera-Vasquez and David G. Dixon
C312
Eiji Tada and G. S. Frankel
C318
Eiji Tada and G. S. Frankel
The effects of a coating of silica particles on the localized corrosion behavior of AISI 304 stainless steel (304SS) during drying of thin electrolyte layers in controlled relative humidity environments were investigated by measurements of the transients of open-circuit potential (OCP) and galvanic current. The silica coatings were composed of spherical silica particles and were deposited on 304SS by cathodic electrophoretic deposition. It was confirmed that the silica layer worked very well as a host layer to soak up electrolyte solutions and that it remained intact under wet and dry conditions. OCP and galvanic current transients indicated that the silica layer affected propagation more than initiation of pitting corrosion. The propagation of pitting corrosion for silica-coated samples was slower than for uncoated 304SS.
C326
Chun-Che Shih, Chun-Ming Shih, Kuang-Yi Chou, Shing-Jong Lin and Yea-Yang Su
The inert properties of gold make it a useful material for implants. Gold was applied as a coating on 316L stainless steel stents to improve the radiopacity and to provide better thrombogenic resistance and a lower degree of restenosis after deployment. Reports of clinical trials using gold-coated stents showed controversial results. A detailed examination of gold-coated stents was designed to understand the influence of surface conditions on the electrochemical properties in vitro. Corrosion resistance of gold-coated stents was investigated by cyclic polarization, and potentiostatic control. Surface morphologies of gold-coated stents in as-received condition, postinflated condition, and after cyclic polarization were characterized by scanning electron spectroscopy (SES). X-ray mapping identified elemental distribution. Results found severe defects in the gold-coating in the as-received condition, cracks and wrinkles on inflated gold-coated stents, and severe corrosion after cyclic polarization. Leaching of metallic ions in Ringer’s solution was possible.
C331
H. Groult, F. Lantelme, I. Crassous, C. Labrugère, A. Tressaud, C. Belhomme, A. Colisson and B. Morel
During the fluorine evolution reaction occurring in the electrolysis of molten KF-2HF, a thin, solid fluorocarbon layer is formed on the carbon anode. The high anodic overvoltage which characterized this process is mainly due to the presence of such a film which drastically changes the wettability of the electrode by the melt. Activation of carbon at
in KF-2HF modifies strongly the surface morphology (scanning electron microscopy) and composition (energy-dispersive X-ray and X-ray photoelectron spectroscopy) of the surface fluorocarbon film. In addition, it enhances the electrochemical performances of the carbon electrodes vs fluorine evolution. Local microconductivity measurements carried out by atomic force microscopy have revealed heterogeneities of composition of the carbon-fluorine film due to the presence of conducting fluorine-graphite intercalation compounds and insulating graphite fluorides
within the film. Finally, the peculiar shape of the fluorine bubbles observed during electrolysis of molten KF-2HF was studied, taking into account the presence of these two fluorocarbon compounds on the surface.
Electrochemical/Chemical Deposition and Etching
D293
C. E. Täubert, D. M. Kolb, U. Memmert and H. Meyer
The adsorption of three different thiol-based additives, commonly used in sulfuric acid copper plating baths, on Cu(111) has been studied by cyclic voltammetry and in situ scanning tunneling microscopy. Adsorption rates were determined and the adlayer growth was monitored for various thiol concentrations. The observed growth peculiarities were tentatively explained by the lifting of a sulfate-induced reconstruction of Cu(111) and, in the case of 3-mercaptopropionic acid, by a bilayer formation.
D300
J. L. Koh, L. K. Teh, F. Romanato and C. C. Wong
The temperature dependence of the growth of cadmium selenide (CdSe) films prepared by galvanostatic electrodeposition in an aqueous acidic bath was examined. We observed a growth mode change at around
, below which the growth rate is reaction rate limited and above which it is transport limited. Growth below
deviates from conventional laws of electrolysis and results in Se-rich “cauliflower” films. At increased temperatures, the films show irregular growth but improved stoichiometry.
D304
Shunsuke Yagi, Kuniaki Murase, Tetsuji Hirato and Yasuhiro Awakura
To develop a surface-finishing technique, an Fe–Cr surface alloying of an iron substrate was investigated using alternating pulsed electrolysis in an aqueous solution containing only Cr(III) ions as a single metal component. In this electrochemical process, the iron substrate was slightly dissolved during the anodic pulse, providing iron ions into the solution in the vicinity of the substrate, while Fe and Cr were both electrodeposited on the substrate surface during the subsequent cathodic pulse. Crack-free or fracture-free Fe–Cr alloy layers with continuous composition gradients were formed on the iron surface under appropriate pulse conditions. Both the thickness and Cr content of the Fe–Cr alloy layer increased with increasing anodic pulse time, suggesting that the Fe(II) ions which dissolved and stayed near the substrate induced the electrodeposition of chromium atoms. The time-dependent concentration distribution of Fe(II) ions in the vicinity of the substrate was digitally simulated through a simple diffusion model using a set of experimental data on current density and current efficiency. The effect of the Fe(II) ion concentration near the substrate surface was discussed in terms of the layer properties, such as chromium content and its anticorrosion behaviors.
D310
Jean Rousset and Daniel Lincot
This paper explores the electrodeposition of thick CdTe semiconductor layers. The electrodeposition of films up to
thick has been achieved under optimized potential and current-controlled conditions in acidic aqueous solutions. The layers were characterized by scanning electron microscopy in order to investigate the morphological and compositional evolutions of the deposited material during the growth. Progressive enrichment in tellurium content, with the formation of an intermediate amorphous cadmium ditelluride phase and morphological transitions from dense to columnar structure, have been observed. These thickness-dependent properties have been compared to those observed with thin films as a function of the applied potential. Current-controlled conditions were also tested and allowed films of up to
to be obtained, but still with a columnar structure. These results are discussed in terms of growth mechanisms.
D316
Yi-Wen Lin, Chia-Cheng Tai and I-Wen Sun
D322
Taku Oyama, Takeyoshi Okajima and Takeo Ohsaka
The cyclic voltammetric behavior of
on glassy carbon (GC) and gold electrodes in room-temperature ionic liquids, i.e., 1-ethyl-3-methylimidazolium tetrafluoroborate
and 1-
-butyl-3-methylimidazolium tetrafluoroborate
has been examined. A series of two-electron (2e-) and one-electron (1e-) reductions of the
redox system could be observed at GC electrode. For example, the cathodic and anodic peaks corresponding to the
redox couple were observed at ca. 0.2 and
vs a Ag wire quasi-reference electrode, respectively, in
, while those observed at
and
were found to correspond to the
redox couple. The disproportionation reaction of the 2e-reduction product of
, i.e.,
to
and Au metal, was also found to occur significantly. A single reduction peak corresponding to the three-electron (3e-) reduction of
to Au metal was observed at Au electrode. The electrodeposition of Au nanoparticles was carried out on GC electrode in these ionic liquids containing
by applying potential-step electrolysis in a different potential range, i.e., the potential was stepped from
to 0 and
, at which the reduction of
to
and Au, respectively, takes place. The results obtained demonstrate that the electrodeposition of gold may occur via a disproportionation reaction of
to
and Au as well as via a series of the reductions of
to
and further,
to Au. The size and morphology of the prepared Au nanoparticles as well as the relative ratio of the Au(111), Au(110), and Au(100) crystalline orientation domains constituting the polycrystalline Au nanoparticles electrodeposited were found to largely depend on the stepped potential (i.e., 0 and
). Interestingly, the Au nanoparticles prepared by a potential-step electrolysis from
are enriched in the Au(110) single-crystalline domain.
D328
Ryosuke Shimizu, Masaaki Ogino, Masakazu Sugiyama and Yukihiro Shimogaki
D334
Y. Xiao, D. W. van der Plas, J. Bohte, S. C. Lans, A. van Sandwijk and M. A. Reuter
In order to investigate an alternative process for the production of primary aluminum via a sulfide intermediate, the electrochemical behavior of
in molten salt has been studied on a laboratory scale. The effects of electrolyte composition, temperature, and cell design on the cell performance have been investigated. Temperature and cryolite addition have positive effects on the current density. Increasing the anode-to-cathode surface area (closer to unity) and shortening the interelectrode distance lead to higher current density. It is concluded that the electrolytic process is governed by the ohmic drop, caused mainly by the sulfur bubbles at the anode.
Electrochemical Synthesis and Engineering
E77
Yi-Wen Chung, Ing-Chi Leu, Jian-Hang Lee, Jung-Hsien Yen and Min-Hsiung Hon
By employing colloidal crystal templates with different colloid diameters, nickel well-ordered macroporous structures (inverse opal) with different void diameters can be fabricated via a template-mediated electrodeposition process. It was found that the different degrees of filling colloidal crystal template produces different nickel nanostructures during the electrodeposition process. Moreover, the filling behavior for electrodeposition of nickel into the template can be characterized in terms of the current transients recorded. Because of preferential nickel-filling into the interstitial spaces among the colloids, fabrication of well-ordered nickel nanorod and monolayer porous arrays are manipulated by controlling electrodeposition times accurately at 5 and
, respectively. However, the macroporous structure covered with hollow sphere arrays on the surface can be formed in
due to preferential nickel-coating around the colloidal surface. Therefore, various kinds of nickel-based structures derived from colloidal crystals can be constructed via a one-step, template-mediated electrodeposition process.
E84
I. M. Petrushina, L. N. Cleemann, R. Refshauge, N. J. Bjerrum and V. A. Bandur
The catalytic NO reduction by methane was studied using a
fuel cell at 135 and
. It has been found that, without any reducing agent (like
), NO can be electrochemically reduced in the (NO, Ar),
,
fuel cell with participation of
or electrochemically produced hydrogen. When added, methane partially suppresses the electrochemical reduction of NO. Methane outlet concentration monitoring has shown the
participation in the chemical catalytic reduction, i.e., methane co-adsorption with NO inhibited the electrochemical NO reduction and introduced a dominant chemical path of the NO reduction. The products of the NO reduction with methane were
,
, and water. The catalytic NO reduction by methane was promoted when the catalyst was negatively polarized
. Repeated negative polarization of the catalyst increased the NO conversion. Maximum NO conversion was 48%. This effect was explained as a result of the reaction of the electrochemically produced hydrogen.
Physical and Analytical Electrochemistry
F95
Qianpu Wang, Michael Eikerling, Datong Song and Zhong-Sheng Liu
We present a model of transport and reaction kinetics in ultrathin cathode catalyst layers for polymer electrolyte fuel cells (PEFCs). In contrast to conventional catalyst layers, ultrathin catalyst layers neither contain a separate electronic conductor, other than the catalyst itself, nor are they impregnated with perfluorinated sulfonic acid ionomer as an intrinsic proton conductor. They can thus be regarded as two-phase composites. The model utilizes Poisson-Nernst-Planck theory for proton transport in the layer. It relates calculated spatial distributions of oxygen and proton concentrations, electrode potential, and electrochemical reaction rates to catalyst utilization and current-voltage performance. By comparison with experimental data from literature for current-voltage relations at low and intermediate current densities the transfer coefficient
of the cathodic reaction was estimated. Catalyst layer thickness, composition, and volume fraction of water-filled pore were systematically varied to determine the values that maximize Pt utilization and voltage efficiency of the layer. The significance of these results for the optimization of catalyst layers in view of operation conditions and synthesis methods is discussed.
F102
Fahd Bensliman, Yuuki Sawada, Kazuya Tsujino and Michio Matsumura
F106
Christopher M. Lang and Paul A. Kohl
The effect of structural rigidity in quaternary ammonium-based ionic liquids (ILs) was investigated.
and
, both 8 atom (7 carbons, 1 oxygen) ether-substituted quaternary ammonium chlorides (Quats), were syn thesized and investigated. In acetonitrile, placement of the oxygen one atom from the nitrogen (Quat I) resulted in a significant decrease in the reductive stability. While the IL form showed similar stability for the two systems, placing the oxygen close to the nitrogen (methyl ethyl ether) appears to localize a greater portion of the positive charge on the nitrogen. This results in an IL with a higher melting point
than the nonether analog,
(III,
) IL. In contrast, placing two carbon atoms between the nitrogen and ether group, ethyl methyl ether (Quat II), delocalizes the positive charge from the nitrogen and produces a room-temperature IL. Neutralization of the acidic IL with sodium chloride resulted in an increase in the bulk conductivity, due to the polar ether group. Upon addition of
or
, which both form a solid-electrolyte interphase on the substrate surface, the increased free sodium ion concentration allowed sodium reduction and oxidation currents greater than
at room temperature.
F111
T. Knutsen, S. Diplas, T. Våland, S. Jørgensen and T. Norby
F122
Wanida Pongsaksawad, Adam C. Powell IV and David Dussault
A phase-field model of electrochemical interface dynamics is developed to study cathode shape and topology change in transport-limited electrolysis in two and three dimensions under conditions of rapid charge redistribution. A case study for the binary model is carried out for an Fe–FeO system. Stability behavior of the model is in good agreement with linear stability theory for small amplitude sinusoidal perturbation in electrodeposition. When there is no convection, a high electric field and low surface tension cause the cathode interface to be unstable, leading to growth of dendrites which break into powders. When the electrodes and electrolyte are low-viscosity fluids, flow provides an additional mechanism for stabilizing the interface. A new stability criterion for this liquid situation based on the Schmidt number is derived from dimensional analysis and model results. For an unstable cathode interface, a streamer morphology (liquid dendrites) is observed in two and three dimensions. This binary model is extended to a ternary system and a representative case is carried out for the Ti–Mg–Cl system. One- and two-dimensional ternary simulations show qualitatively correct interface motion and electrical potential behavior.
F134
J. Agrisuelas, C. Gabrielli, J. J. García-Jareño, D. Giménez-Romero, J. Gregori, H. Perrot and F. Vicente
The conversion process of “insoluble” prussian blue (PB) films into the “soluble” structure has been followed by the simultaneous measurement of current and mass changes during voltammetric experiments and focusing on the possibilities of the use of the instantaneous mass/electrical charge ratio at each potential. A similar procedure was used for the analysis of the mechanism of reduction of PB films to the Everitt’s salt form and to follow the partial dissolution of iron species during the oxidation to the prussian yellow form. The possibility of covering PB films by Nafion membranes, which make difficult the transport of anions through it, allows us to discern the role of anions in the solubilization process of PB films.
Dielectric Science and Materials
G127
Oh Seong Kwon, Sang Woon Lee, Jeong Hwan Han and Cheol Seong Hwang
G134
Takayuki Watanabe, Susanne Hoffmann-Eifert, Lin Yang, Andreas Rüdiger, Carsten Kügeler, Cheol Seong Hwang and Rainer Waser
G141
Jyh-Liang Wang, Yi-Sheng Lai, Sz-Chian Liou, Chen-Chia Chou, Chun-Chien Tsai, Chun-Ping Juan, Huai-Yuan Tseng, Chueh-Kuei Jan and Huang-Chung Cheng
Semiconductor Devices, Materials, and Processing
H417
Hao Jin, K. J. Weber and P. J. Smith
The electrical properties of the
interface following nitridation by ammonia plasma exposure at room temperature indicate that a high density of interface defects and charges is generated by the plasma exposure. Combined high-frequency and quasistatic capacitance-voltage measurements show a dramatic increase in the midgap defect density and interface charge, while quasi-steady-state photoconductivity decay measurements indicate a large increase in carrier recombination at the surfaces, as measured by an increase in the emitter saturation current density. The majority of the defects are not paramagnetic and are annealed out by a thermal treatment at 400°C. However, some defects are also generated by the ammonia plasma exposure which is not removed by subsequent thermal treatments. A combination of ammonia plasma treatment and a subsequent 400°C anneal results in good interface passivation, despite the generation of additional paramagnetic defects, making oxynitride layers produced in this way attractive for potential photovoltaic applications.
H422
Mi-Hee Jung, Stephen P. Beaudoin and Ho-Suk Choi
In this study, the effects of
on the etching of photoresist (PR) on Si wafers in atmospheric-pressure Ar and He plasma have been investigated. The PR etch rate in Ar plasma was several times larger than that in He plasma. It is hypothesized that the Ar was more effective because the density of the Ar plasma was higher than that of the He plasma. In addition, the Ar plasma extended more significantly outside the plasma cavity, and approached the PR more closely than the He plasma at equivalent cavity-PR separation distances. The PR etch rate in
plasma was also higher than that in
plasma at equivalent conditions of plasma power, plasma outlet-to-sample distance, and
content. After the treatment, the PR etched surfaces were examined using contact angle goniometry, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). Contact angle measurements demonstrated that gas mixtures (
or
) are more effective at raising the hydrophilicity of the treated surfaces than single gases (Ar or He). AFM results showed that the morphology of the Si surface following plasma treatment is comparable when either of the single gases (Ar or He) is applied. However, when gas mixtures were applied, the
etched surface was rougher than the
etched surface. The XPS results showed that
atmospheric-pressure plasmas at the conditions studied could effectively remove all PR from wafer surfaces.
H430
Hao Jin, K. J. Weber and A. W. Blakers
The bonded hydrogen concentration in thermally annealed low-pressure chemical vapor deposition (LPCVD)
films increases rapidly following exposure to ammonia plasma and saturates at a concentration determined by the thermal history of the films. Where the nitride layer is deposited on oxidized silicon samples, the introduction of hydrogen into the nitride film using ammonia plasma is effective at passivating the
interface. The plasma treatment does not lead to the generation of a significant number of additional interface defects, shown by lifetime and electronic paramagnetic resonance measurements. Subsequent anneals in nitrogen further improve the interface passivation.
H435
Chun-Hao Tu, Ting-Chang Chang, Po-Tsun Liu, Chi-Feng Weng, Hsin-Chou Liu, Li-Ting Chang, Sheng-Kai Lee, Wei-Ren Chen, Simon M. Sze and Chun-Yen Chang
H440
Zhongshi Liu, Xiping Jing and Lingxuan Wang
, a native defect luminescent material with blue emission, was fabricated by annealing
powders under various
partial pressures or in Ga metal atmosphere. Annealing under low
partial pressure favors the photoluminescence (PL), which indicates that
should be one of the luminescence centers in this phosphor. Annealing in Ga metal atmosphere reduced the PL intensity, which indirectly suggests that
or defect cluster
might be another luminescent center. Electron paramagnetic resonance (EPR) measurements verified the existence of single ionized oxygen vacancy
. An EPR signal with
and four hyperfine lines was observed, which is considered to be related to
and the hyperfine interaction parameter is
. Furthermore, the correlations between PL intensity and the densities of
as well as
were studied. At present, although we can not clarify whether
exists as
or
,
, and
may act as donors, whereas
or
may act as accepters for the luminescence.
H444
Y. Hong, V. K. Devarapalli, D. Roy and S. V. Babu
H454
G. Kissinger, J. Dabrowski, A. Sattler, C. Seuring, T. Müller, H. Richter and W. von Ammon
H460
Yongchai Kwon, Jongwon Seok, Jian-Qiang Lu, Timothy S. Cale and Ronald J. Gutmann
H466
I. M. Dharmadasa, N. B. Chaure, G. J. Tolan and A. P. Samantilleke
Copper indium gallium diselenide layers with
, p, i, n, and
-type electrical conduction, as predetermined, have been electrodeposited from aqueous solutions in a single bath. The photoelectrochemical cell has been used as the key analytical tool to determine the electrical conduction type, and X-ray fluorescence has been used to determine the stoichiometry of the corresponding layers. Optical absorption, X-ray diffraction, and atomic force microscopy have been used to investigate the bandgap, bulk structure, and surface morphology of the material layers, respectively. It has been found that the bandgaps of these layers can be varied in the range
. A four-layer n-n-i-p solar cell structure was fabricated and a corresponding energy band diagram for the device constructed. Current-voltage and capacitance-voltage measurements were carried out to assess the devices, and these parameters (
,
, and
) indicate encouraging characteristics enabling further development of multilayer thin-film solar cells based on
. The addition of a
layer to the structure improved device parameters as expected due to improvements at the metal contact to the
surface of the n-n-i-p-
structure.
H472
Shenghong Qiu and Thomas L. Starr
H476
Ruslan Burtovyy, Yong Liu, Bogdan Zdyrko, Alex Tregub, Mansour Moinpour, Mark Buehler and Igor Luzinov
Atomic force microscopy (AFM) studies of interactions between slurry particles and substrates treated by chemical mechanical polishing (CMP) processes were carried out. To conduct adhesion measurements, the particles present in a CMP system were first attached to the surface of a silicon wafer covered with thin polymer film having high affinity for both particles and the silicon wafer. A silica glass sphere was attached to the AFM cantilever with an appropriate spring constant. The sphere represented the surface of the material being polished and was used as received or covered with a layer of copper. The sphere can be modified with various materials in future research. The AFM force volume mode, which uses the collection of the force-distance curves over selected surface areas, was used for the adhesion measurements. The adhesion in the systems studied was strongly dependent on the pH value of the aqueous environment, and the concentration and type of surfactants added.
H486
Yao-Chen Wang and Tian-Shiang Yang
Chemical mechanical planarization (CMP) has played an enabling role in producing near-perfect planarity of interconnection and metal layers in ultralarge scale integrated devices. For stable and high performance of CMP, it is important to ensure uniform slurry flow at the pad–wafer interface, hence necessitating the use of grooved pads that help discharge debris and prevent subsequent particle loading effects. Here, using two-dimensional lubrication theory and contact mechanics models, we examine the effects of pad groove designs (viz. their width, depth, and spacing) on slurry flow in CMP. It is found that the presence of pad grooves generally increases the slurry flow rate (which clearly facilitates debris discharge) and the magnitude of the subambient fluid pressure (i.e., suction) on the pad–wafer interface. The increased suction implies higher contact stress on the pad–wafer interface, and hence the local material removal rate is expected to increase as well. However, our numerical results suggest that, as a grooved pad has less contact area for effective interaction with the wafer, the overall material removal rate is expected to increase as well. However, our numerical results suggest that, as a grooved pad has less contact area for effective interaction with the wafer, the overall material removal rate is decreased by the presence of pad grooves. There is therefore a trade-off between slurry flow rate enhancement and material removal rate reduction in pad groove design.
H495
Praveen C. Ramamurthy, William R. Harrell, Richard V. Gregory and Apparao M. Rao
Composites of high-molecular-weight polyaniline (PANI) and single-walled carbon nanotubes as well as composites of PANI and multiwalled carbon nanotubes of various weight percentages were prepared using solution processing. The integration and distribution of the carbon nanotubes (CNTs) in the PANI matrix were investigated by various characterization methods. CNT distribution was evaluated using scanning electron microscopy, while CNT dispersion and alignment were characterized by transmission electron microscopy. The specific gravity of the composite material was measured using a density gradient column, which indicates how well the nanotubes are integrated into the polymer matrix. Results indicate that effective integration and distribution of CNTs into a PANI matrix can be achieved with solution processing for composites containing between 1 and 5% CNTs by weight.
H500
Zhongshi Liu, Xiping Jing and Lingxuan Wang
Pure phase
was fabricated by solid state reactions and the products were annealed in various atmospheres, such as
, air,
, vacuum, Zn, and Ge. The material was a native defect phosphor presenting white-bluish emission and its photoluminescence was about 40% brighter than that of the commercial ZnO phosphor. The electron paramagnetic resonance (EPR) measurements showed the existence of
(or
), an abnormal valence for Zn. Additionally,
,
, and ionized
were also detected by EPR. The model for the luminescent emission of this native defect phosphor was proposed, which may arise from the recombination between the donors (
and
) and the acceptors (
and ionized
).
H507
Tanuja Gopal and Jan B. Talbot
H512
Kou-Chiang Tsai, Wen-Fa Wu, Chuen-Guang Chao and Chi-Chang Wu
H517
Wenfeng Xiang, Seokjoon Oh, Hyejung Choi, Rui Dong, Dongsoo Lee, Dongjun Seong and Hyunsang Hwang
H521
J. K. Sheu, K. W. Shu, M. L. Lee, C. J. Tun and G. C. Chi
H525
Ja-Hyung Han, Sang-Rok Hah, Young-Jae Kang and Jin-Goo Park
The stains on the pad caused by polishing by-products can be observed in a copper chemical and mechanical polishing (CMP) process. In this study, the effects of stains on CMP performance such as erosion, dishing, and nonuniformity were evaluated as a function of the degree of stains accumulated on the pad. The stains on the pad deteriorate the nonuniformity of removal rate and result in the increase in erosion and dishing. CMP by-products adhere on both pores and grooves of the pad and block the flow of slurry through the grooves, resulting in the deterioration of nonuniformity. The selectivity (ratio of removal rate, Cu to TaN or dielectric film) is important in order to minimize erosion. When wafers were polished on a stained pad, the removal rate of Cu decreased
due to the poor slurry distribution and the selectivity decreased more than 40% because the mechanical abrasion was enhanced by the presence of by-products on pad surfaces. The lower the selectivity, the higher the level of erosion on the polished patterned wafers. The higher frictional force on a stained pad results in higher temperature and etch rate of Cu which might be the reason for recess and dishing of Cu lines.
H530
Jeng-Yu Lin, Chi-Chao Wan, Yung-Yun Wang, Jui-Chin Chen, Jiun-Yu Lai, Yuh-Da Fan and Jui-Ping Chuang
In this paper, the effect of impurity distribution in copper film on corrosion in chemical mechanical planarization process was studied. The corrosion behavior was investigated by electrochemical and surface analytical techniques. An energy dispersive X-ray analyses attached to a focus ion beam was used to analyze the distribution of impurities. As more impurities were accumulated at the grain boundary, the copper oxide film formed in the slurry tended to be porous. Therefore, corrosion was enhanced. The correlation between corrosion behavior and distribution of impurity was established herein.
H536
Jialin Zhao, Alan C. Seabaugh and Thomas H. Kosel
Sensors and Displays: Principles, Materials, and Processing
J177
Hongbin Liang, Qu Zeng, Zifeng Tian, Huihong Lin, Qiang Su, Guobin Zhang and Yibing Fu
In order to develop a suitable green phosphor for plasma display panels (PDPs), samples
for
, 0.35, 0.50, 0.65, 0.80, and 0.95 were prepared by a solid-state reaction technique at high temperature. The vacuum ultraviolet (VUV, wavelength
and the energy
)—vis spectroscopic properties and decay characteristic were investigated. Because the phosphor
for
shows broad and strong absorption in the vacuum ultraviolet (VUV) range, exhibits higher intensive emission under
excitation, and has a shorter decay time
in comparison with the commercial green PDP phosphor
, it is considered to be a promising green phosphor in PDPs.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K11
Hao Ming Chen, Chia Fen Hsin, Ru-Shi Liu, Shu-Fen Hu and Chao-Yuan Huang
We demonstrate here a simple method to tune the optical properties of thin films of nickel nanowires grown inside an anodic alumina oxide (AAO) template using different anodizing conditions. The optical properties of the metal plate can be effectively tuned by adjusting the thickness of porous alumina oxide. In our case, the thickness of the porous alumina oxide depends strongly on the current density because the duration of anodization maintained constant. The transmission electron microscopic image of the cross section reveals the growth of nickel nanowires which are embedded in porous alumina oxide. Due to the interference between incident light and reflected light, the anodic alumina oxide plate exhibits a variety of color. This demonstration of optical behavior tuning makes it possible to scale up the preparation of metal/oxide nanostructures exhibiting color tuning in the visible region.
Interdisciplinary Topics
P69
Palani Balaya, Janez Jamnik, Jürgen Fleig and Joachim Maier
P77
K. B. Wiles, B. J. Akle, M. A. Hickner, M. Bennett, D. J. Leo and J. E. McGrath
Polymeric electromechanical transducers were identified and based on various novel ion-exchange membranes bonded between two conductive metal layer electrodes. Imposed deformations and small electric fields allowed both sensing and actuation applications. Soft actuator materials produced large bending displacements when only a small voltage was applied across the membrane electrode assembly. Charge motion from one pole to the other pole produced electromechanical coupling effects in the ionic materials through the electric double layer. By increasing the surface area of the electrodes, thereby increasing the capacitance, it was shown that the motion of charges and actuator performance increases, thus indicating a strong correlation between the capacitance and charge motion/performance. Manipulation of the morphology of the electrodes by enhancing the capacitance and effective interfacial area of the conductive electrodes produced major effects on performance and transduction. Transducer actuation performance at lower frequencies was enhanced by employing a novel electrode fabrication technique which could utilize
instead of platinum. At higher frequencies, mass transport and interfacial resistance appeared to play pivotal roles in actuator performance.
P86
Xiaoming Liu, Cuicui Yu, Chunxia Li and Jun Lin
Miscellaneous
S13
Yael Katsir, Lior Miller, Yakir Aharonov and Eshel Ben Jacob