Batteries and Energy Storage
A253
Denis Y. W. Yu, Christopher Fietzek, Wolfgang Weydanz, Kazunori Donoue, Takao Inoue, Hiroshi Kurokawa and Shin Fujitani
A258
E. Ruiz-Trejo, A. Benítez-Rico, S. Gómez-Reynoso and M. Angeles-Rosas
A263
Qingsong Wang, Jinhua Sun and Chunhua Chen
A268
Sun-Ho Kang, Sang-Ho Park, Christopher S. Johnson and Khalil Amine
A275
Ruizhi Yang, Arman Bonakdarpour, E. Bradley Easton, P. Stoffyn-Egli and J. R. Dahn
A283
Young-Ho Rho, Linda F. Nazar, Laura Perry and Dominic Ryan
is a promising cathode material for lithium-ion batteries despite its low intrinsic electronic conductivity. We show, using a combination of Mössbauer, X-ray diffraction, and X-ray photoelectron spectroscopy (XPS), that conductive metal phosphides which enhance its electrochemical performance (
, and metallic
), are generated on the surface of the parent
by reaction with in situ carbon from iron citrate and reducing gases such as hydrogen. Their relative fraction, nature, and location was quantified. Under the most mild reducing conditions, nanosized
is formed on the surface along with
, and carbon resulting from the precursor. Under more aggressive reducing conditions,
is still present, but thermodynamics now favor the formation of
, with fractions varying from 4 to
depending on the temperature and atmosphere used for treatment. Both large
crystallites, and amorphous or nanodimensioned particles are present. XPS studies reveal that the amorphous or nanodimensioned
lies on the inner surface adjacent to the
, and the residual carbon lies on the outer surface. The resulting
“composites” show significantly enhanced electrochemical rate properties as well as outstanding cyclability, which allows a high discharge capacity of
at a 14.8C rate
.
A290
The following article is Free article
Je-Deok Kim, Toshiyuki Mori, Shigenobu Hayashi and Itaru Honma
A295
M. Stanislowski, E. Wessel, K. Hilpert, T. Markus and L. Singheiser
The vaporization of chromium species from chromia scales limits the applicability of chromia-forming steels at high temperatures and is one of the major reasons for degradation in the development of planar solid oxide fuel cells (SOFCs).
vaporized from the interconnector is reduced at the cathode and deposits in the form of solid
-oxide, thereby inhibiting the electrochemical processes. This work presents the first systematic study on the Cr vaporization of Cr-, Fe-, Ni-, and Co-based alloys in air and in
atmospheres at high temperatures. The influence of outer oxide layers of
,
,
,
, and
on the Cr vaporization is investigated. It is shown that the Cr vaporization of chromia-forming steels can be reduced by more than 90% by alloying. An estimate of the expected degradation effects on planar SOFC designs for the use of uncoated interconnector materials is used to show that in order to achieve the desired lifetimes for SOFC systems, additional Cr-retention coatings are necessary. Additionally, equilibrium vaporization measurements are carried out for pure
in humid air in order to elucidate controversies in the literature concerning the thermodynamic data of
.
A307
J. Barker, R. K. B. Gover, P. Burns and A. Bryan
The electrochemical insertion properties of the monoclinic
(
, 0.10, 0.25, and 0.50) phases are presented. Aluminum incorporation induces a modification of the lithium insertion reaction, consistent with increased alkali-ion disorder within the Nasicon structure. Although the reversible specific capacity decreased with aluminum content, the results suggest that the substituted phases may offer some important beneficial properties. Preliminary cycle testing of prototype lithium-ion cells indicated encouraging performance with high material utilization and comparatively low discharge-capacity fade. The highest Al content phase demonstrated the best capacity retention, albeit at the expense of initial specific capacity.
A314
Naoaki Yabuuchi, Yoshinari Makimura and Tsutomu Ohzuku
A322
S. Komaba, T. Itabashi, M. Watanabe, H. Groult and N. Kumagai
Electrochemical reduction and oxidation of a graphite electrode were carried out in nonaqueous electrolytes that consisted of ethylene carbonate/diethyl carbonate (1:1) solvents where
and
were codissolved. Reversible lithium intercalation into graphite occurred accompanied with no remarkable side reactions in the potential range between 1.5 and
vs
, that is, no sodium deposition and no sodium intercalation were observed. Comparing to results in a sodium-free electrolyte, i.e., a conventional electrolyte in Li-ion batteries, the initial irreversibility was noticeably suppressed by codissolving sodium ions, and kinetics of the lithium intercalation were enhanced with better capacity retention during cycling. Additionally, the redox behavior of graphite for lithium-ion batteries was improved by sodium ion coexistence, with no inferior influences on the negative and
positive electrodes and electrolyte. When the sodium ion concentration increased to
, the superior reversibility of lithium intercalation was observed in comparison with that in a sodium-free system; however, the higher concentration of sodium ions deteriorated the lithium intercalation properties. We found that a surface layer formed on graphite electrode got less resistive as a lithium-ion conductor by entrapping sodium during the initial electroreduction with optimal
concentration.
A331
Joykumar S. Thokchom and Binod Kumar
A337
H. Xia, L. Lu, Y. S. Meng and G. Ceder
A343
Hyojin Lee, Hansu Kim, Seok-Gwang Doo and Jaephil Cho
Ge nanoparticles with different particle sizes confined in a carbon matrix were prepared by annealing Ge nanoparticles terminated with butyl groups at 400, 600, and
. X-ray diffraction and transmission electron microscopy results showed that the Ge nanoparticles’ size increased from
as the annealing temperature of the as-prepared samples increased from
. Raman spectra confirmed that the parts of the Ge nanoparticles were not covered by the carbon starting at
after annealing for
. Moreover, the graphitization degree of the carbon increases with increasing temperature, and the sample, annealed at
for
, showed the graphitization degree. Electrochemical cycling results revealed that the
Ge nanoparticles, confined in a carbon matrix obtained after annealing the as-prepared sample at
for
, showed the best charge capacity of
with 12% capacity loss after
. On the other hand, Ge nanoparticles that had not been covered with the carbon matrix showed a rapid capacity decrease, along with pulverization of Ge nanoparticles to a size of about
after cycling.
A347
Kazuhisa Naga, Tsuyoshi Nakajima, Yoshimi Ohzawa, Zoran Mazej, Boris Žemva and Henri Groult
A353
T. Nonaka, C. Okuda, Y. Seno, Y. Kondo, K. Koumoto and Y. Ukyo
A359
I. Ruth Mangani, C. W. Park, Y. K. Yoon, J. H. Beom and J. Kim
A364
K.-F. Chiu, H.-Y. Tang and B.-S. Lin
A369
F. H. B. Lima, J. R. C. Salgado, E. R. Gonzalez and E. A. Ticianelli
A376
Mariko Miyachi, Hironori Yamamoto and Hidemasa Kawai
A381
Mathieu De Koninck, Simon-Claude Poirier and Benoît Marsan
Fuel Cells and Energy Conversion
B371
Rasmus Barfod, Mogens Mogensen, Trine Klemensø, Anke Hagen, Yi-Lin Liu and Peter Vang Hendriksen
B379
Takeshi Komatsu, Hajime Arai, Reiichi Chiba, Kazuhiko Nozawa, Masayasu Arakawa and Kazunori Sato
Chemical reactivity of
(LNF) with
has been investigated in order to examine the long-term stability of the LNF phase at
, which shows a high performance as the cathode of intermediate-temperature solid oxide fuel cells (IT-SOFCs). The chemical stability of LNF was compared with that of
(LSM) under the existence of
. The LNF powder, a powder mixture of LNF and
, and a powder mixture of LSM and
were, respectively, heated at
, and they are analyzed by X-ray powder diffraction with the Rietveld refinement. We found that the LNF phase maintains the hexagonal crystal system heated in air up to
. In the
mixture, the LNF phase kept its pristine crystal structure while a new phase,
, was detected, which was produced by the reaction between
and the residual
contained in the starting LNF powder. In the
mixture, LSM reacted with
and produced a significant amount of
. LNF showed a much better chemical stability against
than LSM. LNF can serve as a long-life cathode in the IT-SOFC system.
B383
I. A. Schneider, S. A. Freunberger, D. Kramer, A. Wokaun and G. G. Scherer
B389
Kyung Joong Yoon, Wenhua Huang, Guosheng Ye, Srikanth Gopalan, Uday B. Pal and Donald A. Seccombe Jr.
B396
Choong-Gon Lee, Do-Hyung Kim and Hee-Chun Lim
B405
Adam Z. Weber and John Newman
In this paper, results from mathematical, pseudo two-dimensional simulations are shown for four different along-the-channel thickness distributions of both the membrane and cathode catalyst layer. The results and subsequent analysis clearly demonstrate that for the membrane thickness distributions, cell performance is affected a few percent under low relative-humidity conditions and that the position along the gas channel is more important than the local thickness variations. However, for the catalyst-layer-thickness distributions, global performance is not impacted, although for saturated conditions there is a large variability in the local temperature and performance depending on the thickness.
B413
Joshua L. Hertz and Harry L. Tuller
Thin-film composite electrodes with nanometric grains of platinum and yttria-stabilized zirconia (YSZ) were reactively sputtered onto single-crystal yttria-stabilized zirconia. The activation polarization resistance exhibited an activation energy of
and was found to have an approximate inverse dependence on microelectrode radius squared, consistent with, effectively, a mixed ionic–electronic conductive nature. Area specific polarization resistances of less than
were achieved at 400°C in a dense thin-film electrode. The attractiveness of these nanocomposite electrodes for use in microfabricated solid oxide fuel cells (SOFCs), of interest as portable power sources, is discussed.
B419
Volker Paul Schulz, Jürgen Becker, Andreas Wiegmann, Partha P. Mukherjee and Chao-Yang Wang
A full morphology (FM) model has been developed for studying the two-phase characteristics of the gas diffusion medium in a polymer electrolyte fuel cell (PEFC). The three-dimensional (3D) fibrous microstructure for the nonwoven gas diffusion layer (GDL) microstructure has been reconstructed using a stochastic technique for Toray090 and SGL10BA carbon papers. The FM model directly solves for the capillary pressure-saturation relations on the detailed morphology of the reconstructed GDL from drainage simulations. The estimated capillary pressure-saturation curves can be used as valuable inputs to macroscopic two-phase models. Additionally, 3D visualization of the water distribution in the gas diffusion medium suggests that only a small number of pores are occupied by liquid water at breakthrough. Based on a reduced compression model, the two-phase behavior of the GDL under mechanical load is also investigated and the capillary pressure-saturation relations are evaluated for different compression levels.
B427
G. J. la O’, B. Yildiz, S. McEuen and Y. Shao-Horn
Corrosion, Passivation, and Anodic Films
C189
Hiroshi Goto, Noboru Akao, Nobuyoshi Hara and Katsuhisa Sugimoto
C195
M. Kendig and P. Kinlen
Galvanic reduction of an oxidatively formed disulfide polymer of 2,5-dimercapto-1,3,4-thiadiazole (polyDMcT) in a conducting carbon paste releases its monomer anion in neutral
NaCl. The monomer anion exhibits very good oxygen reduction reaction (ORR) inhibition at Cu cathodes. Coupling a carbon paste containing polyDMcT to a freshly polished metallic Al surface releases a corrosion inhibiting reduction product from the paste that can diffuse to and inhibit a remote cathode. This chemistry forms the basis for a “smart” corrosion inhibiting material that will release an ORR inhibitor when a corrosive environment couples the material to a base metal as would be the case for a coating with a defect. No release would occur in the absence of either the reducing force of the base metal, or the presence of a coupling ionic (corrosive) environment.
C202
N. Vasiljevic, L. T. Viyannalage, N. Dimitrov, N. A. Missert and R. G. Copeland
C209
M. Reid, J. Punch, C. Ryan, L. F. Garfias, S. Belochapkine, J. P. Franey, G. E. Derkits Jr. and W. D. Reents Jr.
Pure copper samples were exposed in an environmental chamber for 2, 4, 7, 15, and
at 90% relative humidity,
, and
hydrogen sulfide (
). Samples were subsequently subjected to microscopy and microanalysis using different techniques: scanning electron microscopy, energy analysis dispersive X-ray spectroscopy, X-ray diffraction, focused ion beam (FIB), and secondary ion mass spectroscopy. The corrosion samples were cross sectioned and the different corrosion layers were imaged using FIB. After
exposure the predominant corrosion products were copper sulfide
and cuprite
. Once the
reached a minimum thickness, the rate of growth of the layer became parabolic due to the limiting
diffusion through a thickening film. As the layers reach a critical thickness
internal stresses and defects in the corrosion layer allow virtually free access of
and O to the underlying layers, consequently accelerating the film growth.
C215
Edouard Asselin, Akram Alfantazi and Steven Rogak
Electrochemical/Chemical Deposition and Etching
D195
Sunjung Kim and David J. Duquette
D201
W. Shao, G. Pattanaik and G. Zangari
D208
D. Josell, T. P. Moffat and D. Wheeler
Bottom-up superconformal feature filling during electrodeposition, called “superfilling,” that is used for industrial processing of damascene copper interconnects has also been demonstrated during electrodeposition of silver and gold. The curvature enhanced accelerator coverage (CEAC) mechanism has been proposed to underlie all three processes and has been used to quantitatively predict observed filling of patterned features. The key feature of the CEAC mechanism is redistribution of adsorbed additives through changes of local surface area as dictated by mass conservation and the relative strengths of adsorption. Previous studies of CEAC-mediated superfilling have neglected adsorbate diffusion along the surface that might arise during deposition due to the CEAC-induced gradients in surface coverage. This paper extends the CEAC model to include such diffusion, applying the resulting formulation to understand differences in the geometries of experimental superfilling systems.
D215
Te-Ming Chen, Fu-Ming Pan, Jui-Yi Hung, L. Chang, Shich-Chuan Wu and Chia-Fu Chen
D220
Kazuhisa Azumi, Shinnosuke Egoshi, Satoshi Kawashima and Yuuichi Koyama
Etching pretreatment in
solution was applied to magnetron sputter-deposited Al–Si alloy films formed on a glass plate to improve uniformity of Zn deposition in the double zincate process. In the etching process, a small amount of Cu was deposited on the alloy surface at a very high density to accompanying Al dissolution. These deposits acted as nucleation seeds for Zn deposition, resulting in uniform, fine and thin Zn layers on Al alloys in a zincate process. This effect was more prominent on Al alloys containing 2.0 or 2.6 atom % of Si than on those containing 0 or 1.0 atom % of Si. Such a discrepancy was caused by increased Cu deposition on Al–Si alloys with relatively high Si concentration.
D227
J. Y. Chen, Y. M. Liao, C. C. Lee and G. C. Chi
D230
Xiaohai Li, Timothy O. Drews, Effendi Rusli, Feng Xue, Yuan He, Richard Braatz and Richard Alkire
A multiscale simulation model was developed to simulate shape evolution during copper electrodeposition in the presence of additives. The model dynamically coupled a kinetic Monte Carlo (KMC) model (for surface chemistry and roughness evolution) with a finite volume (FV) model (for transport and chemical reactions in the electrolyte) and a level-set code (for tracking macroscopic movement of the metal/electrolyte interface). The KMC code was coarse-grained and used a multisite mesoparticle approach to account for the adsorption of large molecules. A multilevel grid approach was used to achieve numerical efficiency and accurate interface tracking. The model was demonstrated for an application involving in-fill of two-dimensional trenches by copper electrodeposition with additives [bis(3-sulfopropyl)disulfide], polyethylene glycol, chloride, and l-(2-hydroxyethyl)-2-imidazolidinethione. Demonstration calculations were carried out with use of initial estimates for the physicochemical parameters associated with a proposed reaction mechanism. The approach was found to be feasible for computing stable, dynamic behavior during macroscopic shape evolution over extended periods of time while simultaneously tracking microscopic roughness evolution associated with nearly molecular scale events at the surface. Numerical results include predictions of the surface concentration distributions as a function of time and distance for each reactant, product, and intermediate species associated with the proposed reaction mechanism.
D241
Shou-Yi Chang, Yu-Shuien Lee and Chia-Ling Lu
In this study, the interface chemistry and adhesion strengths between Cu and SiCN etch stop layers have been investigated under different plasma treatments. From the examination of interface microstructures and the analyses of chemical compositions and bonding configurations, an oxide layer was found to exist at the untreated
interface. After
and
treatments, the amount of oxides was effectively reduced. Some Cu silicides formed during SiCN deposition, and Cu nitrides even formed under
plasma treatment. The adhesion strengths of the
interfaces were measured by nanoindentation and nanoscratch tests under which interface delamination occurred around indented regions. The adhesion energy of the untreated
interface was obtained as about 4.98 and
, respectively, by nanoindentation and nanoscratch tests. After
and
plasma treatments, the adhesion energy was effectively improved to 5.90 and
by nanoindentation test, and to 1.74 and
by nanoscratch test, respectively, because of the removing of oxides and the formation of Cu silicides and nitrides at the
interfaces.
D249
Yael Katsir, Lior Miller, Yakir Aharonov and Eshel Ben Jacob
Qualitative observations of electrochemical deposition in thin circular cells have shown that radio-frequency (rf) irradiation of zinc sulfate solutions can dramatically affect the deposition patterns. For some growth parameters the rf-treatment can even induce morphology transitions between the dense branching morphology and dendritic growth. We found that the effects of rf-treatments can last for a long time (hours). In addition, detailed studies using electron microscopy observations reveal that the effects span on all scales, from the micrometer-scale organization to the self-organization of the macroscopic pattern. We propose that these changes of patterning on all scales resulted from singular effects of gas-filled submicrometer bubbles or nanobubbles, which are generated by the rf-irradiation. The idea is that hydration shells around the nanobubbles induce water ordering that acts as a new singular perturbation mechanism in the solution. The latter is in addition to the well studied microscale singular perturbation mechanisms in the deposit (surface tension and attachment kinetics). We also studied electrochemical deposition in zinc sulfate solutions prepared from water that is doped with nanoparticles under rf-irradiation, and found similar and even amplified effects. Moreover, the nanoparticle doping stabilizes the effects—they are retained months after the solutions were prepared.
D260
Jay Y. Kim, Youn-Geun Kim and John L. Stickney
Au(111) single-crystal substrates were used in studies of Cu nanofilm formation by electrochemical atomic layer deposion (ALD). Cu undepotential deposition (UPD) was used to deposit the first Cu atomic layer on a Au(111) substrate, modified with an atomic layer of I atoms. By definition, Cu UPD results in the formation of an atomic layer, thus, to deposit subsequent Cu, surface-limited redox replacement (SLRR) was used. The SLRR involved initial formation of Pb UPD on the Cu-coated surface just described. This Pb UPD-coated surface was then exposed to
at open-circuit potential (OCP), where the Pb atoms were exchanged for Cu. In the ultrahigh-vacuum electrochemical (UHV-EC) studies presented here, two Pb UPD potentials were investigated:
and
. UHV-EC studies involved use of a surface analysis instrument with optics for low-energy electron diffraction and Auger, and to which was attached an ante-chamber containing a Pyrex glass electrochemical H-cell. In this way, surface analysis was performed without transfer of the deposit through air and the contamination which would result. In addition, studies of the first few cycles of redox replacement were investigated using electrochemical in situ scanning tunnel microscopy (STM), with a flow cell for solution exchange to prevent loss of potential control.
D267
Y. B. Yun, D. J. Kim, S. M. Park, N.-E. Lee, K. S. Kim and G. H. Bae
D273
Takuya Shimada, Hiromi Nakai and Takayuki Homma
Oxidation reaction mechanisms of reductants for electroless Ag deposition process were investigated using density functional theory calculation, focusing upon behavior of the reaction intermediate species. It was indicated that the oxidation processes of reductants, such as dimethylamine borane, formaldehyde, and hypophosphite ion, on the Ag surface are initiated by addition of
and proceed via five-coordinate intermediate species. Catalytic activity of the Ag surface for the oxidation reaction of the reductants was investigated by using energy density analysis, focusing upon the local interaction of the species. The results indicated that the adsorption of the reductants onto the Ag surface is driven by destabilization of the reductant and stabilization of the Ag surface. It was also indicated that the destabilization of the five-coordinate intermediate species at the Ag surface is a key factor of the “catalytic activity” for the oxidation reaction. In the case of the reaction of formaldehyde, in which the Ag surface acts as catalyst, the intermediates were considerably activated at the Ag surface, whereas such an effect was not clearly seen with the hypophosphite ion, for which the Ag surface is not catalytic. It was also suggested that the activation of the intermediates is affected by coordination behavior of
species.
Electrochemical Synthesis and Engineering
E63
Hiromasa Goto
The optical rotatory dispersion and circularly dichroism of the chiral conjugated polymer polybithiophene prepared in a cholesteric liquid crystal are examined. Change in the optical rotation of the polymer depends on the redox conditions, with a maximum optical rotation of
. The ellipticity of this polymer is also found to exhibit hysteresis with redox cycle. These results demonstrated that the optical rotation of the chiral polymer could be controlled via the electrochemical redox potential.
E68
Adam L. Friedman and Latika Menon
We have carried out a systematic study of the electrodeposition process to understand the effect of varying three important quantities on the synthesis of nanowires inside porous alumina templates. We have electrodeposited iron nanowires inside porous alumina to determine the optimal settings of these variables to induce effective and efficient nanowire growth. First, we vary the pH of the electrolyte solution to show that pH has little effect on the deposition rate. Second, we vary the magnitude of the applied ac voltage to show that the deposition rate increases with increasing voltage. Finally, we vary the frequency of the applied ac voltage to show that there are three distinct regions corresponding to different deposition rates. We have studied the magnetic properties of the synthesized nanowires and our results as a function of fabrication parameters are discussed.
E71
Kazuki Arihara, Chiaki Terashima and Akira Fujishima
Physical and Analytical Electrochemistry
F65
Gregory W. Bishop, Jonathan A. Karty and Dennis G. Peters
Catalytic reduction of 1,1,1-trichloro-2,2,2-trifluoroethane (CFC-113a or Freon 113a) by cobalt(I) salen electrogenerated at a carbon cathode in dimethylformamide (DMF) containing
tetramethylammonium tetrafluoroborate
has been investigated with the aid of cyclic voltammetry, controlled-potential electrolysis, gas chromatography–mass spectrometry, and high-performance liquid chromatography-electrospray ionization-mass spectrometry (HPLC-ESI-MS). Cyclic voltammetry reveals that CFC-113a and two of its degradation products, 2,2-dichloro-1,1,1-trifluoroethane (HCFC-123) and 2-chloro-1,1,1-trifluoroethane (HCFC-133a), can all undergo catalytic reduction by cobalt(I) salen. Controlled-potential (bulk) electrolyses of cobalt(II) salen in the presence of CFC-113a lead to the production of HCFC-123, HCFC-133a, 2-chloro-1,1-difluoroethene (HCFC-1122), and 1,1-difluoroethene (HFC-1132a). HPLC-ESI-MS has been employed to demonstrate that, during the bulk catalytic reduction of CFC-113a, the salen ligand of the catalyst is modified through addition of a
or
moiety to an imino
bond. On the basis of documented knowledge about the electrochemistry of cobalt-containing complexes, together with the results of our cyclic voltammetry and bulk electrolysis experiments, a mechanistic scheme is proposed for the cobalt(I) salen-catalyzed reduction of CFC-113a.
F70
X. Zhang, S. Stewart, D. W. Shoesmith and J. C. Wren
F77
J. A. Squella, L. J. Núñez-Vergara, A. Campero, J. Maraver, P. Jara-Ulloa and J. Carbajo
Dielectric Science and Materials
G85
Hua-Gen Peng, Dong-Zhi Chi, Wei-De Wang, Jing-Hui Li, Kai-Yang Zeng, Richard S. Vallery, William E. Frieze, Mark A. Skalsey, David W. Gidley and Albert F. Yee
G95
David L. Witker, Sean O. Clancy, David J. Irvin, John D. Stenger-Smith and Jennifer A. Irvin
G99
Yan-Kai Chiou, Che-Hao Chang, Chen-Chan Wang, Kun-Yu Lee, Tai-Bor Wu, Raynien Kwo and Minghwei Hong
Semiconductor Devices, Materials, and Processing
H259
Chyuan Haur Kao, Chao Sung Lai and Chung Len Lee
H263
Chih-Wei Hu, Feng-Ming Lee, Kun-Fu Huang, Chia-Lung Tsai and Meng-Chyi Wu
In this article, we demonstrate a simple and low-cost method to fabricate the
strained multiquantum-well
buried-heterostructure (BH) laser diodes (LDs) by using the single-step metallorganic-chemical-vapor-deposition (MOCVD) regrowth and self-aligned technique. The active region is buried by the intrinsic
layer which is used as the current-blocking layer as well as the electrical and optical confinement layer. The BH LDs have a calculated internal quantum efficiency of 81% and an internal loss of
. The fabricated as-cleaved BH LDs exhibit a threshold current of
, a maximum light output power of
at
, a maximum operating temperature of
, and a characteristic temperature of
in
. The BH LDs with an as-cleaved front facet and a high reflectivity coating
applied to the rear facet can increase the maximum operation temperature up to
and have a light output power exceeding
at
and
. The
frequency at a bias current of
is 8.0, 6.5, and
at 30, 60, and
, respectively. Besides, the
modulation bandwidth can be extended as far as
at
and
. These results confirm that BH LDs have the potential capacity for high-speed fiber optic applications.
H268
Fu-Hsiang Ko, Hsin-Chiang You, Chun-Ming Chang, Wen-Luh Yang and Tan-Fu Lei
H271
Arun Vijayakumar, Ravi M. Todi and Kalpathy B. Sundaram
H275
M. M.A. Hakim and P. Ashburn
H283
Der-Feng Guo, Chih-Hung Yen, Jung-Hui Tsai, Wen-Shiung Lour and Wen-Chau Liu
H289
Ssu-I Fu, Tzu-Pin Chen, Rong-Chau Liu, Shiou-Ying Cheng, Po-Hsien Lai, Yan-Ying Tsai, Ching-Wen Hung and Wen-Chau Liu
In this work, the characteristics of the
heterojunction bipolar transistors with different emitter-edge-thinning thickness were systematically investigated. A stronger downward-band-bending phenomenon was observed at the edge of emitter-edge-thinning intersection with the exposed base surface. This band bending induced the presence of a potential saddle point, which substantially increased the recombination rates and electron densities. In addition, the decision of emitter-edge-thinning thickness plays a key role in reducing surface recombination at the potential saddle point. As the emitter-edge-thinning thickness was selected between 100 and
, the lowest recombination rate and electron density and highest dc current gain could be obtained. Furthermore, good agreements between the theoretical analyses and experimental results were found.
H293
S. Hayashi, R. Sandhu and M. S. Goorsky
H297
P. Thiyagarajan, M. Kottaisamy and M. S. Ramachandra Rao
H304
Chien-Neng Liao, Tong-Her She, Po-Jui Liao and Hsu-Shen Chu
H309
Andy Eu-Jin Lim, Wan Sik Hwang, Xin Peng Wang, Doreen Mei Ying Lai, Ganesh S. Samudra, Dim-Lee Kwong and Yee-Chia Yeo
H314
Qingchun Zhang, Chia Wai Han and Chunxiang Zhu
In this work, the formation of nickel germanide is investigated by spectroscopic ellipsometry. The phase transition and thickness of nickel germanide were identified nondestructively by spectroscopic ellipsometry. The results were compared with traditional analytical tools such as four point probe, Rutherford backscattering spectrometry, and X-ray photoelectron spectroscopy, and showed good agreement. The optical properties (refractive index) of nickel germanide were obtained from spectroscopic ellipsometer measurements and applied to the thickness measurement of nickel germanide successfully.
H318
Byung Joon Choi, Seol Choi, Yong Cheol Shin, Cheol Seong Hwang, Jin Wook Lee, Jaehack Jeong, Yoon Jung Kim, Sung-Yeon Hwang and Suk Kyoung Hong
H325
M. J. Hernández, M. Cervera, J. Piqueras, M. A. González, M. Avella, T. del Caño and J. Jiménez
Sensors and Displays: Principles, Materials, and Processing
J121
Wei-Ning Wang, W. Widiyastuti, I. Wuled Lenggoro, Tae Oh Kim and Kikuo Okuyama
J129
Leta Y. Woo, L. Peter Martin, Robert S. Glass and Raymond J. Gorte
An electrochemical cell
serves as a model system to investigate the effect of
and
. Possible mechanisms responsible for the response are presented. Two dense Au electrodes are co-located on the same side of a dense YSZ electrolyte and are separated from the electrolyte by a porous YSZ layer, present only under the electrodes. While not completely understood, the porous layer appears to result in enhanced
response. Impedance data were obtained over a range of frequencies
, temperatures
, and oxygen (2–18.9%) and 
concentrations. Spectra were fit with an equivalent circuit, and values of the circuit elements were evaluated. In the absence of
, the effect of
on the low-frequency arc resistance could be described by a power law, and the temperature dependence by a single apparent activation energy at all
concentrations. When both
and
were present, however, the power-law exponent varied as a function of both temperature and concentration, and the apparent activation energy also showed dual dependence. Adsorption mechanisms are discussed as possibilities for the rate-limiting steps. Implications for impedancemetric
sensing are also discussed.
J136
Masahiro Takesada, Tetsuhiko Isobe, Hisamitsu Takahashi and Shigeo Itoh
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K1
Krzysztof Winkler, Emilia Grodzka, Francis D’Souza and Alan L. Balch
Interdisciplinary Topics
P49
Ming-Kwei Lee and Tsung-Hsiang Shih
High-quality nanoscaled fluorine and nitrogen co–doped anatase-phase titanium oxide can be obtained from the conversion of ammonium oxotrifluorotitanate by thermal treatment. The photocatalytic activity of titanium oxide treated at
shows the highest photocatalytic activity and is about 1.31 times of P-25 due to higher fluorine and nitrogen doping. The heterojunction of zinc sulfide/titanium oxide prepared by metallorganic vapor-phase epitaxy shows 1.51 times the photocatalytic activities of commercial P-25. Both nanoscaled titanium oxide and zinc sulfide/titanium oxide heterojunction show a proportional relationship between carrier lifetime and photocatalytic activity.
P52
D. A. Koleva, J. H.W. de Wit, K. van Breugel, Z. F. Lodhi and E. van Westing
The electrochemical behavior of steel reinforcement in conditions of corrosion and cathodic protection was studied, using electrochemical impedance spectroscopy (EIS) and compared to reference (noncorroding) conditions. Polarization resistance (PR) method and potentiodynamic polarization (PDP) were employed as well, in addition to ac 2 pin electrical resistance monitoring, thus deriving a comparison of the involved parameters, mainly polarization resistance and bulk electrical properties, obtained by all methods. It was found out that EIS is readily applicable for evaluating electrochemical behavior of the steel surface not only for corroding or passive state, but also in conditions of cathodic protection, although the interpretation of derived parameters is not straightforward and is related to the properties of the product layers, formed on the steel surface in the different conditions. For verification of the latter dependence, EIS, PDP, and PR measurements were performed additionally in cement extract solution, using steel samples from the previously embedded rebars in all technical conditions. The bulk matrix properties in passive, corroding, or under-protection conditions can be well defined by EIS. The evaluation of the electrochemical behavior of the steel surface, in terms of deriving polarization resistance, should take into account the crystallinity, morphology, and composition of the surface layers, which were investigated by scanning electron microscopy and energy dispersive X-ray analysis.
Miscellaneous
S3
S. J. Young, L. W. Ji, S. J. Chang and X. L. Du
S4
C. J. Lan, W. Y. Liu and T. S. Chin
S5
Rajesh Katamreddy, Ronald Inman, Gregory Jursich, Axel Soulet and Christos Takoudis
S6
Vicky Mei-Wen Huang, Vincent Vivier, Mark E. Orazem, Nadine Pébère and Bernard Tribollet
S7
Vicky Mei-Wen Huang, Vincent Vivier, Isabelle Frateur, Mark E. Orazem and Bernard Tribollet
S8
Vicky Mei-Wen Huang, Vincent Vivier, Mark E. Orazem, Nadine Pébère and Bernard Tribollet
S9
Kang Xu