Electrochemical Science and Technology TECHNICAL PAPERS
593
Jeffrey M. Calvert, Bryndyn Weiner, Jerry J. Smith and Robert J. Nowak
598
R. Koksbang, D. Fauteux, P. Norby and K. A. Nielsen
605
H. S. Lim, J. D. Margerum, S. A. Verzwyvelt, A. M. Lackner and R. C. Knechtli
613
Dennis A. Corrigan and Sandra L. Knight
620
Zen‐ichro Takehara, Kiyoshi Kanamura and Makoto Kawanami
Lead dioxide film deposited on the gold plate was discharged under various conditions. Lead sulfate was formed only on the electrode surface during the discharge at 30°C. On the other hand, lead sulfate was formed on the electrode surface and also at the interface between lead dioxide film and the gold plate during the discharge at 50°C. The crystal size of lead sulfate formed at the interface was larger than that formed on the electrode surface. The shape of lead sulfate formed at the interface was like a plate. These facts indicate that lead sulfate film formed at the interface causes the passivation of the electrode. The oxidation rate of lead sulfate formed at the interface was much slower than that formed on the surface. Therefore, the reaction temperature is the most important factor for the failure of a lead‐acid battery by the passivation at the interface between the grid and active mass.
625
Z. Ogumi, Y. Uchimoto and Z. Takehara
Ultrathin polymer membranes are prepared by polymerizing octamethylcyclotetrasiloxane in glow discharge. Membranes formed by glow discharge (plasma) polymerization are uniform and pinhole‐free. Polymeric solid electrolyte membranes are prepared by hybridization of plasma polymer formed from octamethylcyclotetrasiloxane, poly(propylene oxide), and lithium perchlorate. The films are about 1 μm thick and show high ionic conductivity of the order of 10−6S · cm−1 (10 Ω cm2 resistance per unit area of solid polymer electrolyte) at 60°C. The conductivity depends on the content of lithium perchlorate, and its temperature dependence fits with the WLF‐type equation rather than the Arrhenius equation.
630
J. Y. Huot, A. Van Neste, L. Brossard and R. Schulz
The electrolytic hydrogenation of
in acid solution leads to the amorphous transformation of the alloy. This new technique of synthesizing amorphous metallic glasses permits fine control of the hydrogen fugacity, the hydrogen flux, and the total amount of absorbed hydrogen. The hydrogenation can be performed at much higher hydrogen fugacity compared with gaseous hydrogenation. The hydrogen diffusion kinetics are also investigated.
635
Gery R. Stafford
640
B. J. Feldman and O. R. Melroy
By simultaneously measuring the copper deposition rate and the current, we have determined the partial currents corresponding to the oxidative and reductive half‐reactions for electroless Cu deposition from an EDTA, formaldehyde solution. These experiments were performed in a solution containing both copper and formaldehyde. The copper deposition rate was measured in situ with a quartz crystal microbalance. The resulting partial I/V curves are different from those obtained by others who used separated (one component missing) half‐cells. Specifically, we find that formaldehyde catalyzes the electrochemical reduction of Cu(EDTA). These observations help explain discrepancies between previously measured I/V curves for the independent oxidative or reductive half‐cells, and the predictions of mixed potential theory concerning the electroless Cu deposition rate.
644
Woon‐kie Paik, Thomas E. Springer and Supramaniam Srinivasan
Platinum gauze electrodes coated with the proton‐conducting polymer, Nafion, were investigated with respect to the kinetics of the oxygen reduction and hydrogen oxidation reactions. The coated electrodes were in contact with a Nafion membrane electrolyte. The current‐potential behavior of the coated electrodes depended upon the thickness of the coating. The electrodes with thicker coatings exhibited less activation and ohmic control but encountered diffusion limitations. Those with thinner coatings showed significant ohmic control. A theoretical analysis was made for the current‐potential relation and the current distribution using a model of a Nafion‐coated wire in contact with the membrane. The present analysis confirms the necessity of optimizing the amount of Nafion impregnation in low‐Pt‐loaded, porous gas‐diffusion electrodes, as was experimentally observed in another study in our laboratory.
649
Masatoshi Fujii, Tomoji Kawai and Shichio Kawai
656
Jeffrey T. Glass, George L. Cahen Jr. and Glenn E. Stoner
661
The following article is Free article
Steven J. Visco, Catherine C. Mailhe, Lutgard C. De Jonghe and Michel B. Armand
A broad class of organosulfur compounds is discussed which may offer unique advantages as positive storage electrodes in advanced battery systems. The organosulfur electrodes operate between ambient and 150°C, are inexpensive, and inert to many metals. In addition, the physicochemical and electrochemical properties of the organosulfur electrodes may be varied in a predictable way. At room temperature these materials may be crystalline, liquid, or polymeric. Batteries based on the novel organosulfur positive electrodes and sodium metal negative electrodes have theoretical energy densities ranging from 350 to 600 Wh/kg. The system which has to date been studied in most detail is the sodium/tetraethylthiuram disulfide (TETD) couple which has a theoretical energy density of 360 Wh/kg and an open‐circuit voltage of 2.3 V. Laboratory cells have been assembled and tested with maximum practical energy densities of over 110 Wh/kg at zero current drain and volumetric energy densities of 0.196 Wh/cm3. These cells have been cycled between 10 and 90% of available capacity at power densities of 6 Wh/kg at an energy density of 80 Wh/kg and overall energy efficiency of 75%. Some experimental batteries delivered peak power densities of 40–60 W/kg for a period of a minute or more. Further, preliminary testing of batteries using simple alkyl disulfide electrodes have resulted in full charge/discharge cycles at current densities of 10 mA/cm2 at 105°C.
665
Edward K. Yung, Brian W. Hussey, Arunava Gupta and Lubomyr T. Romankiw
A focused argon ion laser beam (514.5 nm) has been used to induce etching of manganese‐zinc‐ferrite ceramics in aqueous
solutions. In the absence of the laser beam the etching process did not take place even at the boiling point of the selected etchant. For
concentration above 2N, bubble‐free etching took place in the presence of the laser beam. Within the range of 2–8N for
concentration, the depth of the etched grooves increased with increasing laser power, decreasing scan speed, and increasing
concentration. Evidence of decreasing average etch rate due to mass transport limitation was observed under low
concentration, high laser power, and low scan speed conditions. The width of the etched grooves increased with increasing laser power, but was relatively insensitive to the scan speed and the
concentration. The experimental findings of the laser‐assisted etching of Mn‐Zn‐ferrite can be qualitatively interpreted by a thermally activated reaction mechanism: formation at and above a threshold temperature of an active chemical environment on the surface for the initiation of the etching process; more concentrated etchant allows more abundant supply of the reactive species and requires less heat input to reach the active state. Etching of ferrite occurs as a result of the reaction between the active etchant (possibly fused
) and either the solid or the molten ferrite, depending on the laser power. The etching process generates soluble product species and the profiles of the etched patterns are strongly influenced by the mass transport characteristics of the etching system. A mathematical model for the surface temperature distribution, which takes into account heat loss into the liquid, is also presented.
673
Gleb Mamantov and T. M. Laher
677
M. C. Pham, F. Adami and P. C. Lacaze
The detection of the phenoxy radical during the anodic oxidation of 2–6 disec‐butyl phenol confirms the radical mechanism and the possibility of the MIRFTIRS method in the in situ study of process occurring at the interphase electrode‐solution.
679
R. S. Parikh and K. C. Liddell
The partial differential equations describing the mass transfer to a rotating ring disk electrode where the intermediate generated at the disk electrode is decomposed by chemical reaction in the solution have been solved by the orthogonal collocation technique. The two spatial dimensions (normal and radial) are discretized leaving a continuous dependence in time. The space in the normal direction is discretized by exponentially weighted polynomials, whereas the “shifted” Jacobi polynomials are used in the radial direction. Results are presented for an electron transfer at the disk and ring together with decomposition of the intermediate generated at the disk by first or second order kinetics. Two different boundary conditions at the disk are investigated, namely, a constant potential in the limiting current region and a constant applied current. The transient and steady‐state currents at the disk and the ring electrodes, as well as the simulated collection efficiency, are in excellent agreement with previous theoretical treatments. This algorithm, however, is much more accurate and takes much less computer time as compared to other techniques. The working curves provided allow the determination of rate constants of homogeneous reactions from ring current‐rotation rate data obtained from a rotating ring disk electrode.
688
David E. Stilwell and Su‐Moon Park
The degradation reaction kinetics of oxidized polyaniline has been studied employing rotating ring‐disk electrode techniques. Polyaniline films were grown on the disk electrode and were then oxidized at a potential more positive than 0.90V vs.
, while the degradation product (benzoquinone) was monitored at the ring electrode at an applied potential of 0.05V. The product was monitored either with the disk potential maintained at >0.90V (closed‐circuit experiment) or with the disk circuit disconnected after the polyaniline film was oxidized for some time (open‐circuit experiment). The results of closed‐circuit experiments indicate that electrochemical generation of oxidized polyaniline was a limiting step and its rate decayed for a given amount of polyaniline film according to the zeroth order. The rate of hydrolysis for the oxidized polyaniline in quinonoid forms was determined to be consecutive first order from open‐circuit experiments. The dependencies of the hydrolysis reaction on the acidity of the degradation medium and sulfate concentrations have also been studied; the results are consistent with the Schiff base hydrolysis mechanism.
698
Bianting Sun, J. J. Jones, R. P. Burford and M. Skyllas‐Kazacos
Thick, freestanding, flexible films of polypyrrole have been prepared from pyrrole monomer in propylene carbonate solvent containing tetra ethyl ammonium p‐toluene sulfonate electrolyte. Films were electrodeposited onto titanium substrates at temperatures from −40° to 25°C, and were found not only to have high conductivity, but were also anisotropic. The electrodeposition temperature, electrode dimensions, current density, voltage, and solvent were found to affect the properties of the polymer. The values of conductivity of the polypyrrole films increased with decreasing electrodeposition temperature and increasing current density. For a
substrate, the highest conductivity value, 514 S/cm, was obtained with samples prepared at a temperature of −20°C and a current density of 3.0 mA/cm2. The ratio of conductivities measured along
and across
the surface of the samples increased with decreasing electrodeposition temperature and current density, but was strongly dependent on the electrode geometry. A conductivity of 996 S/cm and a
ratio of 3.3 was obtained for a film deposited on a long narrow substrate, compared with a ratio of 1.2 for a square substrate. Films produced in propylene carbonate solvent possessed better properties than when either acetonitrile or mixtures of propylene carbonate and acetonitrile were employed as solvents.
702
Yoshihito Ikariyama, Shigeru Yamauchi, Tomoaki Yukiashi and Hiroo Ushioda
Enzyme electrodes were microfabricated by electrochemical incorporation of enzyme molecules into the continuously electrochemically developing micropores of platinum black particles. Two electrochemical processes, electrochemical adsorption of enzyme molecules and reductive deposition of metallic microparticles from its complexal form, were simultaneously carried out by using a microelectrode of diameter ranging from 10 to 200 μm. An amperometric glucose sensor, consisting of a glucose oxidase‐incorporated microelectrode, demonstrated high performance characteristics including high sensitivity and fast response.
707
Pawel J. Kulesza and Larry R. Faulkner
713
Simon S. Wang
A microelectrode array coated with a ionically conducting polyethylene oxide (PEO) film was developed for lubricant studies. With this microarray, the ohmic resistance of the bulk lubricant layer can be reduced considerably. In addition, since all electrodes stay in the conducting PEO medium, stable potentials can be established between the working and the reference electrodes. Lubricant additives, some of which are electrochemically reactive but exist in a poorly conducting medium, the oil‐based lubricant, can then be extracted (in situ) into the PEO medium and react at the working electrode. With this device, current originating from two different lubricant additives was measured separately for the first time.
716
M. Pujadas and P. Salvador
In order to go further into the mechanisms of water splitting at platinized
powder suspensions, the photoelectrochemical behavior of both bare and electroplatinized
single crystal in
and
saturated electrolytes has been studied by electrolyte electroreflectance (EER) and photocurrent transient techniques. EER is shown to be an interesting tool to follow the potential distribution changes occurring at the
interface during photo‐ and electrochemical reactions. In particular, reversible shifts of the
flatband potential, due to local pH changes associated with
evolution, could be detected for the first time by EER. Direct experimental evidence has shown that equilibrium of OH− and H+ ions between the electrolyte and the
surface is reached in times no longer than a few seconds. The combined information obtained from EER and photocurrent transient experiments with the platinized
single crystal, strongly suggests that the ∼1 V Schottky barrier existing at the
microjunctions drastically collapses when the electrolyte in the interface with the semiconductor becomes
saturated. Evidence is also shown that either dissolved or evolved
can be photo‐oxidized with holes trapped at Pt islands. This constitutes an important source of surface recombination, responsible to a great extent for the low water splitting efficiency at platinized
suspensions. Finally, it can be inferred from our experimental results that, in colloidal systems, band asymmetry between bare and platinized zones is not a sine qua non condition for water splitting to be a feasible process. Nevertheless, the barrier height diminution at the
contact upon interaction of Pt with
seems to be decisive for
to evolve with an acceptable rate at Pt islands. On the other hand, Pt plays an important role as a catalyst by reducing the overpotential for
evolution, which can occur in spite of the small energy difference between the
redox level and the
conduction bandedge.
723
Dennis A. Corrigan and Richard M. Bendert
Binary 9:1 composite hydroxides of nickel with 13 other metals were prepared by cathodic electrocoprecipitation from metal nitrate solutions and characterized by cyclic voltammetry in
. Under these conditions, coprecipitated Ce, Fe, and La strongly catalyzed the oxygen evolution reaction. Conversely, Cd, Pb, and Zn poisoned this reaction. The hydrogen evolution reaction was less affected by the coprecipitated metals; Ag and Pb had a catalytic effect on this reaction. Co and Mn shifted the nickel hydroxide redox potentials to more cathodic values. In contrast, Cd, Ce, Cr, Fe, La, Y, and Zn each shifted these redox potentials anodically. The coulombic efficiency of the oxidation‐reduction process was substantially lowered by Ce, Fe, and La.
TECHNICAL NOTES
728
Thomas Z. Fahidy
730
Norio Takami and Nobuyuki Koura
Solid‐State Science and Technology TECHNICAL PAPERS
732
T. Wada, M. Sugimoto and T. Ajiki
Corrosion of thin aluminum is one of the important failure mechanisms in integrated circuits. In our work, aluminum corrosion and electrolytic leakage current have been studied by temperature‐humidity‐bias tests. Two different passivation layers were investigated; a double layer of nondoped silicate glass (NSG) on phosphosilicate glass (PSG), and single layer of plasma‐deposited silicon nitride
. Samples were prepared with three different combinations of width/spacing: 2/2 μm (width/spacing), 4/4 and 12/6 μm, 2/2 and 4/4 μm patterns with a passivation layer on the stripes and a 12/6 μm pattern in which a part of the passivation layer is etched to expose the aluminum stripe. Investigation of these aluminum patterns via temperature‐humidity‐bias tests leads to the following conclusions. (i) With
passivation, cathodic aluminum corrosion did not occur on 2/2 and 4/4 μm patterns. On the other hand, with
passivation, cathodic corrosion occurred on three patterns. (ii) In 12/6 μm patterns with
passivation, the leakage current increases earlier than that of 2/2 and 4/4 μm
passivated patterns. Thus, it is confirmed that leakage current conducts through the interface between the passivation layer and the plastic resin. (iii) In a special aluminum pattern in which a part of
passivation layer is etched to expose the stripe, local anodic corrosion was dominant. This anodic corrosion can be explained by the fluorine in
plasma used for
etching.
736
Robert Forbes and Stefan Zukotynski
740
Edward W. Kiewra and Peter C. Wayner Jr.
A linear thin‐film array of silicon carbide thermistors has been developed to measure temperature profiles near the contact line of an evaporating liquid meniscus. The array consists of 80,
square silicon carbide thermistors on a 3 in. diam single crystal of silicon. The devices are spaced at 50, 250, and 1000 μm intervals along the wafer. Temperature data are obtained through the use of an external electronic data acquisition system. This arrangement enables an accurate evaluation of the heat flux occurring in an evaporating thin liquid film, and it should also be suitable for temperature measurements in many other situations.
745
J. J. Krajewski and D. W. Kisker
In this study, we have used mass spectrometry to investigate the efficiency of activated carbon as a scrubbing agent for removal of organometallic tellurium compounds from a vapor stream. Using a common tellurium source for organometallic chemical vapor deposition, diethyltellurium, we find that activated charcoal scrubbing is very efficient, removing this compound to below our detection limit of 10 ppb. We have investigated the effect of carbon loading, flow, and concentration on the scrubbing efficiency of two different types of charcoal and a granular alumina.
748
Tetsuya Osaka, Jun Kawaguchi and Hideo Sawai
The thermal stability of electroless Ni‐P alloy thin film resistors for pulse heating was investigated using the step stress test method. The resistance of electroless Ni‐P resistors is decreased by pulse heating. It was confirmed by a micro x‐ray diffraction analysis of the resistors after the step stress test that this resistance decrease is due to crystallization of the resistor films. The degree of crystallization can be quantitatively evaluated as the temperature coefficient of resistance of Ni‐P films calculated from resistance changes during pulse heating. The step stress test is demonstrated to be an effective and quick method of determining the thermal stability of thin film resistors for pulse heating, and it also gives an evaluation of the temperature coefficient of resistance of thin film resistors.
753
H. Matsubara, M. Toda, T. Sakuma, T. Homma, T. Osaka, Y. Yamazaki and T. Namikawa
756
Edward K. Yung and Lubomyr T. Romankiw
Through‐hole plating experiments were carried out with a gap cell and with Plexiglas boards. The gap cell provided good simulation of the plated through‐hole system and allowed accurate and nondestructive profile analysis of copper deposits. As the current density and the aspect ratio were increased, the copper distribution inside the hole (gap) became more nonuniform. Plugging of holes was observed at high current levels due to current crowding into the hole entrance where the mass transport rate was high. The experimental findings were confirmed by mathematical models which were developed on the basis of electrochemical engineering principles and were applied to the geometric domain that included both the surface of the board and the through‐hole wall. The limits of present through‐hole plating technology are pointed out and possible means for process improvement are discussed.
768
K. Ryoo, R. Drosd and W. Wood
Ion implantation damage that transforms to crystallographic defects such as dislocation loops or stacking faults with heat‐treatments is unavoidable in VLSI device fabrication. Dislocation loops were introduced into three different regions of p+‐n junction such as the p+, the depletion, or the n region by Si implantation followed by annealing. Stacking faults were introduced into the p+ region or extended into the depletion region of p+‐n junction by Si implantation followed by oxidation. Locations, densities, and characteristics of the extended defects were scrutinized with transmission electron microscopy (TEM). In forward bias, diodes having dislocation loops still show diffusion currents with the ideality factor equal to 1, regardless of their locations, only increasing the ohmic resistance at forward bias higher than 0.5V. In addition, dislocation loops in the depletion or the n region caused higher diffusion current levels than control diodes which did not have dislocation loops. In reverse bias, dislocation loops in the n region caused the smaller generation current than those in the depletion region, whereas dislocation loops in the p+ region caused current levels as low as control diodes. Stacking faults in the p+ region functioned similarly to dislocation loops in the p+ region except for showing higher ohmic resistance than dislocation loops, even though the densities of the former were much lower than those of the latter. Only stacking faults extending into the depletion region caused the large leakage currents which degrade the diode functions.
772
D. T. C. Huo, M. F. Yan, J. D. Wynn and D. P. Wilt
775
H. Zogg, S. Blunier and J. Masek
779
A. Behfar‐Rad, S. S. Wong, R. J. Davis and E. D. Wolf
782
C. I. H. Ashby, D. R. Myers and F. L. Vook
The etch rate of a solid‐excitation‐based photochemical etching process for semiconductor materials is determined by the balance between recombination of photogenerated carriers and carrier participation in the surface etching reaction. Ion implantation‐induced damage of the semiconductor can shift the balance between recombination and reaction, permitting selective etching of undamaged regions of a semiconductor surface relative to ion‐implanted, damaged regions. Spatially selective photochemical dry etching of
has been achieved by this approach.
785
B. K. Singh, Anuradha Chatterjee, A. N. Daw and R. N. Mitra
Ohmic contacts to p‐type silicon having resistivity of the order of 5 Ω‐cm and orientation <111> were fabricated by an electroless Ni‐B process. It has been found that boron content in the deposit varies from 5–27% using sodium borohydride as the reducing agent. The contact resistance decreases as the boron content in the deposit increases with heat‐treatment.
787
Mark E. Collingham and Richard L. Zollars
It has been proposed that a recycle loop would increase the uniformity of the coating thickness in a low pressure chemical vapor deposition reactor. Research was conducted to analytically and experimentally evaluate the effects of recycling on the axial coating thickness uniformity during the deposition of polycrystalline silicon. This research shows that considerable improvement in the uniformity can be obtained through the use of a recycle loop. The amount of improvement depends upon a variety of factors, including pressure, temperature, gas velocity through the reactor, and the recycle ratio. Furthermore, these improvements can increase the uniformity of the wafers while decreasing the amount of reactants required to produce an acceptably thick coating. This is accomplished primarily by operating the reactor at a high conversion so that the amount of reactants lost in the outlet gas is minimized.
794
John D. Cressler, Wei Hwang and Tze‐Chiang Chen
An experimental and theoretical investigation of the temperature dependence of the dc conductivity in heavily arsenic‐doped polycrystalline silicon thin films is presented. Measured results indicate that the carrier trapping model which is traditionally used to describe polysilicon transport fails in the heavy doping regime. After consideration of alternative models, the electrical nature of the grain boundary is found to be best described as a conduction process with two different activation energies. Reasonable agreement with data is obtained when the grain and grain boundary conductivities are combined using a model of the film microstructure. Nonuniform grain size and distributions are considered.
805
H. Norström, S. Nygren, T. Johansson, R. Buchta, M. Östling, A. Lindberg, U. Gustafsson and C. A. Petersson
A polycide process with silicided diffusions is presented. This allows simultaneous use of mutually different silicides on the gate electrode and on the respective source and drain areas. The novel technique was used to fabricate MOSFETs and
gate electrodes and self‐aligned
on source/drain regions. Respective sheet resistivities were 5 and 7–8 Ω/□ and no degradation effects were observed. A comparison with the more conventional salicide concept is made and several advantages are elucidated.
810
Al F. Tasch, H. Shin, C. Park, J. Alvis and S. Novak
815
R. T. Tung, J. L. Batstone and S. M. Yalisove
819
Michael E. Coltrin, Robert J. Kee and Greg H. Evans
We describe a mathematical model of the coupled fluid mechanics and gas‐phase chemical kinetics in a rotating disk chemical vapor deposition reactor. The analysis is for the flow between an infinite radius, heated nonporous rotating disk and a parallel infinite radius porous surface through which reactive fluid is injected normal to the disk. The analysis extends the usual von Karman transformation to allow specification of the normal velocity at the porous disk, and reduces to a stagnation point flow in the limit of zero rotating rate. The deposition of silicon from silane is used as an example system. A new reaction mechanism and set of rate constants are given for the thermal decomposition of silane. We present an RRKM analysis of several of the unimolecular reactions in the mechanism. Calculated velocity and temperature profiles, chemical species density profiles, and deposition rates as functions of susceptor temperature, spin rate, and inlet flow velocity are presented.
829
Laurence Bigio
Two laser techniques are used to derive absolute densities and radial density distributions for the three
excited states of mercury in the positive column of a low pressure Hg‐Ar dc discharge. Radial density distributions are obtained using a saturated laser absorption technique, while absolute densities are measured using the hook method (an interferometric technique). Results are shown and discussed for a variety of discharge currents and pressures.
835
G. M. Choi, H. L. Tuller and J. S. Haggerty
Nonstoichiometry and charge transport properties of
have been investigated as functions of doping level, temperature, and thermal history. Undoped and
single‐crystals and undoped,
,
,
,
,
, and
polycrystalline specimens of
have been characterized using complex impedance techniques. The magnitude of ionic conductivities, pre‐exponentials, and activation energies were found to be insensitive to dopants or doping concentrations. Thus a model of
as an intrinsic oxygen ion conductor was found to be most appropriate. This represents the first identification of an intrinsic fast oxygen ion conductor with noncubic crystal symmetry. The conductivity along the [100] direction was found to be approximately two orders of magnitude higher than that along the [001] direction consistent with the anisotropic character of the crystal structure. The conductivity of both single and polycrystalline samples decreases exponentially with time as observed previously for stabilized zirconia.
839
R. Pretorius, M. A. E. Wandt, J. E. McLeod, A. P. Botha and C. M. Comrie
843
M. Benlyamani, F. Ajersch and G. Kennedy
847
Jenq‐Gong Duh and Jyh‐Wei Lee
During high temperature oxidation of Fe‐8.9Al‐3Cr‐31Mn‐0.87C alloys at 1000°C, an oxidation‐induced transformed α layer is observed between the γ matrix and the oxide scale. The morphology of the oxidized sample and the elemental redistribution of the constituents are evaluated using an electron microprobe. The formation of the α layer is caused by the selective oxidation of manganese, and its thickness of the α layer increases with the oxidation time and temperature. The growth of the α layer obeys a modified parabolic rate law at 1000°C. The diffusivity of manganese in the α layer at 1000°C is evaluated on the basis of the interfacial compositions at the γ/α and the α/oxide interfaces along with the proposed diffusion‐related formulation.
853
A. Derre, M. Ducarroir and F. Teyssandier
The influence of various parameters controlling chemical vapor deposition of
on steel are studied by means of experimental designs. Temperature, molar fraction of methane, deposition time, and total flow rate are the main factors with respect to three responses: weight increase, thickness, and yield. Thermodynamic calculations allow one to explain the etching of the substrate under reduced pressure by chemical exchange Fe‐Ti. The three response surfaces are determined as a function of the main factors.
858
D. B. M. Klaassen, D. M. De Leeuw and C. A. H. A. Mutsaers
Multilayer interference filters enhance the luminance, emitted in the forward direction, of cathode‐ray tubes used for projection television. These filters also affect the chromaticity of the emitted light. Both effects are calculated from first principles. Using these calculation methods, it is found that by the use of multilayer interference filters, the chromaticity of practically all blue emitting phosphors can be brought within the E.B.U. recommendations for the blue primary. Moreover, this change in chromaticity can be achieved without any loss in white‐D capability.
863
Yoshiyuki Sato, Masahiro Yanagida, Hiroshi Yamanaka and Hideo Tanigawa
The reflectance and structure changes of iridium oxide films by reduction were investigated in an attempt to apply the films to optical data storage media. The films were prepared by the thermal oxidation of iridium‐carbon composite films. The films were easily reduced by heating them in 5%
in Ar at temperatures in the range 100°–300°C. When the films were reduced, the particle size of Ir metal and the reflectance of the films increased with an increase in the reducing temperature. The reduced films were stable against oxidation at temperatures of 250°C or higher. Optical writing on the films was carried out with an argon laser at 0.84W power. The writing mechanism was based on changes in the film's optical properties caused by laser‐induced reduction.
867
Kiumars Ghowsi and Robert J. Gale
An analytical model for the growth kinetics of the anodic oxidation of Si is developed, in which oxidant anions are drifted across the as‐grown
by the electric field from an applied constant voltage. Literature evidence for an anionic transport mechanism is reviewed. The theoretical model derived for the film growth rate is consistent with an empirical relation due to Jain et al.,
, where
represents the oxide thickness as a function of time, and
and
are constants (3). The net anion mobility was calculated using the model and earlier experimental results. Electronic current density, the major total current component, is shown to be nonohmic and space charge limited. Equations are derived, each as a function of time, for the total current density, the electronic current density, and the ionic efficiency during anodic oxidation. These theoretical predictions are in good agreement with the available experimental data.
TECHNICAL NOTES
872
Yasushiro Nishioka, Hiroshi Shinriki and Kiichiro Mukai
873
M. N. Kozicki, J. M. Robertson, H. Kheyrandish and A. E. Hill
876
R. Kwor, R. J. Matson, M. M. Al‐Jassim, S. Polchlopek, P. L. F. Hemment and K. J. Reeson
878
M. N. Kozicki and J. M. Robertson
882
N. Yokoyama, K. Hinode and Y. Homma
ACCELERATED BRIEF COMMUNICATIONS
885
Yee‐Min Wuu, Fu‐Ren F. Fan and Allen J. Bard
887
V. Mitrovic‐Scepanovic and R. J. Brigham
889
R. D. S. Yadava and R. K. Bhan
891
J. L. Yeh, S. Z. Liu, B. Schwartz and M. J. Vasile
893
R. M. Williams, B. Jeffries‐Nakamura, M. L. Underwood, B. L. Wheeler, M. E. Loveland, S. J. Kikkert, J. L. Lamb, T. Cole, J. T. Kummer and C. P. Bankston
895
Z. Nagy, N. C. Hung and R. M. Yonco
897
K. L. Siefering and G. L. Griffin
899
Peter S. Fedkiw and Wei‐Hwa Her