Batteries and Energy Storage
090501
Kepiao He, Yonglian Xiong, Chao Zhang, Zhiting Dou, Ting Yi, Shengqiang Lin, Chunsheng Li and Yan Sun
This paper studied the electrochemical performance and heat generation characteristics of 18650 LiMn0.6Fe0.4PO4/LiNi0.5Co0.2Mn0.3O2 (LMFP/NCM) composite cathode materials for lithium-ion batteries under different states of health (SOH) (98%, 90% and 82%). The discharge performance, temperature rise and heat generation of these three batteries were investigated at different discharge rates and different temperatures. The electrochemical impedance spectroscopy (EIS), internal resistance and entropy heat coefficient at different depths of discharge (DOD) were analyzed. The results showed the internal resistance and irreversible heat generation increased with the decrease of battery SOH value. The entropy heat coefficient significantly increased at 0.5 DOD, and the maximum total heat generation power was also obtained at 0.5 DOD. The maximum heat generation power of 90% and 82% SOH batteries at 0.5 DOD increased by 175% and 208% than 98% SOH battery when discharging at 2 C, respectively. The battery with 82% SOH had the highest temperature rise (7.5 °C) and total heat generation power (3.12 W), and the ratio of reversible to irreversible heat generation was the lowest (0.152) at −10 °C. It provided a theoretical basis for optimizing the thermal management of LMFP/NCM batteries.
090502
The following article is Open access
Matt D. R. Kok, Anmol Jnawali, Thomas M. M. Heenan, Thomas G. Tranter, Dan J.L. Brett, Paul R. Shearing and James B. Robinson
Extending the lifetime of commercial Li-ion cells is amongst the most important challenge to facilitate the continued electrification of transport as demonstrated by the substantial volume of literature dedicated to identifying degradation mechanisms in batteries. Here, we conduct a long-term study on a cylindrical Li-ion cell, tracking the evolution of the structure of the cell using X-ray computed tomography. By evaluating the internal geometry of the cell over several hundreds of cycles we show a causal relationship between changes in the electrode structure and the capacity fade associated with cell ageing. The rapid aging which occurs as cells reach their end-of-life condition is mirrored in a significant acceleration in internal architecture changes. This work also shows the importance of consistent and accurate manufacturing processes with small defects in the jelly-roll being shown to act as nucleation sites for the structural degradation and by extension capacity fade.
090503
Shin-ichi Iida, Masahiro Terashima, Kazutoshi Mamiya, Takahito Kimoto and Shunsuke Sasaki
Recently, researchers are extensively developing next-generation batteries, including all-solid-state batteries (ASSBs), to meet the increasing demand for electric vehicles (EVs) and renewable energy storage. Li metal has been considered an ideal anode material due to its high theoretical capacity and low redox potential. However, it is highly reactive and severe side reactions occur at the interface between Li metal anode and solid electrolytes (SEs), significantly affecting battery performance. Therefore, Li metal anodes have not yet been commercialized. To obtain a chemically stable Li metal anode, the authors examined the side reactions at the interface between the Li metal anode and oxide-type SE using surface analysis techniques such as time-of-flight secondary ion mass spectrometry (TOF-SIMS), X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and low-energy inverse photoelectron spectroscopy (LEIPS). In this paper, we present the results of interface analysis between Li metal anode/SE and discuss how to obtain a stable Li metal anode.
090504
Nemanja Latas and Nikola Cvjetićanin
Anatase TiO2 was prepared in the form of nanotube arrays by anodic oxidation of Ti foil followed by annealing at 400 °C. Electrochemical experiments, which included cyclic voltammetry (CV), galvanostatic (GS) cycling and electrochemical impedance spectroscopy (EIS) were conducted in 1 M solution of LiClO4 in propylene carbonate (PC) at temperatures 25 °C–55 °C. CV experiments, at scan rates 5–50 mV·s−1, demonstrated with increasing temperature a large increase in the intensity of the redox peaks along with a decrease in the peak-to-peak separation. GS cycling showed large increase of capacity of thin-wall TiO2 nanotubes with increasing temperature, which attains 357 mAh·g−1 at 55 °C during lithiation at current rate 5.3 C, with capacity retention of 98.5% and Coulombic efficiency of 97.5%. Surface storage and development of secondary voltage plateau strongly contribute to such a large capacity value. EIS showed a multiple decrease in solid electrolyte interphase (SEI) layer resistance and charge transfer resistance with temperature rising up to 55 °C.
090505
The following article is Open access
Stefan Oswald, Moritz Bock and Hubert A. Gasteiger
The rising interest in single-crystalline NCMs (LiMO2, M = Ni, Co, Mn) has generated numerous publications which feature promising results in terms of cycle-life improvement when compared to the conventional polycrystalline analogues. To elucidate the effect of the two morphologies on the capacity retention and the internal resistance, this study aims to discriminate the effect of different degradation phenomena of polycrystalline and single-crystalline NCM851005 (LiNi0.85Co0.10Mn0.05O2) in coin full-cells cycled against graphite anodes. The impact of the particle morphology is analyzed over the course of more than 200 charge/discharge cycles for two temperatures of 25 and 45 °C, applying 4.1 or 4.4 V as upper cutoff voltages. The morphology-dependent surface area changes, resulting mainly from the tendency of polycrystalline NCMs towards particle cracking upon calendering, charging, and extended cycling, are quantified via krypton-gas physisorption, and the consequences of particle cracking regarding the amount of gas evolution, transition-metal dissolution, loss of lithium inventory, and resistance build-up are evaluated. In particular, the pronounced cathode impedance build-up of polycrystalline NCMs, investigated by electrochemical impedance spectroscopy using a micro-reference electrode in full-cells, exposes the impact of particle cracking and the induced electronic resistances within a secondary agglomerate on the rate capability.

Highlights
Comparison of polycrystalline (PC) and single-crystalline (SC) NCM in full-cells
Extended cycling in full-cells under mild and harsh conditions
Evaluation of surface-area-dependent side reactions (metal dissolution and gassing)
Counterintuitively, despite lower surface area, better rate capability of SC
Difference in performance governed by particle cracking of PC
090506
Bhamiti Sharma, Haidar Y. Alolaywi, Bing Tan, David Shepard, Yunkui Li, Yuhao Liao and Yang-Tse Cheng
Lithium (Li) metal batteries are attractive due to their high gravimetric and volumetric energy densities. However, they can fail catastrophically due to dendritic nucleation, growth, and penetration through the polypropylene (PP) or polyethylene (PE) separators. Poor electrolyte wetting and non-uniform Li ion flux are known to affect Li dendrite formation, especially since the PP/PE separators have non-uniform pore size distribution and typical organic electrolytes do not wet them well. In this work, we demonstrate that a porous zeolite coating on a commercial PP separator can improve electrolyte wettability and through plane ionic conductivity, giving rise to more uniform Li flux. Consequently, coated separator can delay dendrite penetration and enhance cell performance and safety. We tested Celgard 2400 (uncoated) and zeolite-coated separator (coated) in high energy NMC||Li cells for their rate capability and cycle life performance. Rate capability test for these cells shows that the additional resistance due to the zeolite coating can negatively impact the cell performance at high C-rates. However, cells with the coated separator outperform those with uncoated separator in the cycle life test with improved capacity retention. Symmetric cell studies performed to understand the differences in Li plating morphology indicate initial lower overpotential for the coated separator cells, revealing improved electrolyte wetting and relatively uniform Li flux. Scanning electron microscopy (SEM) reveals zeolite-coating microstructure with evenly distributed zeolite particles and cycled Li metal electrode morphologies. SEM images show much smoother Li plating morphology on Li metal surface in the cells with coated separators. This study highlights the potential of using zeolite-coated separators to enhance lithium metal battery (LMB) performance and safety.

090507
Madhushri Bhar, Vivek Vishwakarma, Kaliprasad Yalamanchili and Surendra K. Martha
With the advent of globalization, the upsurge of lithium-ion battery (LIB) production and generation of spent batteries impose a severe threat as hazardous e-waste and resource sustainability of crucial elements like cobalt and lithium. Herein, we propose one-step regeneration of cobalt oxide (RCO) from cycled LiCoO2 (LCO)-type cathode via carbon anode-assisted reduction. The inherent structural changes resulting in high irreversibility are minimized in conversion-type mixed-phase recycled cobalt oxide anode due to less Li-ion consumption and stable SEI formation during initial cycles. Replacement of conventional Cu-foil current collector with carbon-fiber (CF) based freestanding electrode further enhances the Li-ion storage capacity with overall active material utilization, accommodating volume changes in the internal void spaces and providing mechanical stability. Electrochemistry reveals that RCO@CF and RCO@Cu deliver an initial discharge capacity of 3800 mAh g−1 and 1432 mAh g−1 at 30 mAg−1 with 77% and 64% coulombic efficiency that becomes ∼97% in the following cycles. Besides, RCO@CF shows an average discharge capacity of 730 mAh g−1 at 300 mA g−1 over 300 cycles, which is ∼2.7 times that of recycled graphite anode (270 mAh g−1). The sustainable recycling strategy described herein rejuvenates the cycled LCO-type cathode as an appealing anode material for LIBs.

090508
The following article is Open access
Weiran Gao, Javit Drake and Fikile R. Brushett
In response to challenges in the thermal management of lithium-ion batteries (LIBs), we investigate the concept of circulating electrolyte through the porous electrodes and separator to facilitate effective, uniform, and real-time temperature regulation. We show, through physics-based electrothermal modeling and dimensional analysis of a single, planar LIB cell, that electrolyte convection can simultaneously draw heat from the cell and suppress heat generation from entropy change, charge-transfer, and ohmic losses, and that the cell temperature rise can be effectively mitigated when heat removal matches or exceeds heat generation. These findings distinguish internal convection from external surface cooling approaches used in conventional thermal management that often lead to a tradeoff between heat and mass transport. In a simulated exemplary 5.7-C case, a LIB cell with stationary electrolyte must stop discharging at only 54% of its capacity due to cell temperature rise to an upper threshold (325 K); with sufficient electrolyte flow (∼1 μm s−1 for a single cell, or a residence time of ∼200 s), the cell can be maintained below 315 K while delivering 98% of its capacity. Finally, to illustrate the potential for dynamic temperature regulation, we simulate scenarios where cells already experiencing self-heating can instantly arrest temperature rise with the onset of convection.

090509
The following article is Open access
Ortal Breuer, Gayathri Peta, Yuval Elias, Hadas Alon-Yehezkel, Yu-Ting Weng, Miryam Fayena-Greenstein, Nae-Lih Wu, Mikhael D. Levi and Doron Aurbach
Composite solid electrolytes with ceramic particles dispersed in a polymer matrix are considered a correct choice for all-solid-state batteries. These electrolytes balance the high ionic conductivity of superionic-ceramic conductors and the elasticity of polymers. Here, Li||LiFePO4 batteries with 30 wt% of LATP embedded in PEO20:LiTFSI show superior performance at elevated temperature. After ∼150 cycles, cells retained 84% of their original capacity compared to only 51% for batteries with no additive. At 5 C cells demonstrate 43% higher capacity. In symmetric cells with blocking and non-blocking electrodes and all-solid-state batteries LATP lowers the impedance of the electrode-electrolyte interface ensuring cycling stability. LATP improves performance by stabilization of the cathode-electrolyte interface, apparently the major contributor to the cell impedance.

090510
The following article is Open access
Jiaqiang Huang, Charles Delacourt, Parth Desai, Charlotte Gervillié-Mouravieff, Laura Albero Blanquer, Ruifeng Tan and Jean-Marie Tarascon
Battery ageing is inevitable for chemistry of any kind and still occupies a central place in battery research and development. However, the operando monitoring of battery ageing under real working conditions remains largely unexplored. Herein, we demonstrate the feasibility of using fiber Bragg grating sensors to operando monitor the thermal (temperature and heat) evolutions of commercial 18650 sodium-ion cells during long-term cycling ageing. With the delicate heat deconvolution, the evolutions of entropy and overpotential heat rates upon the cycling ageing are decoded, while the ageing-driven changes in overpotential components are further analysed. Drawing also on thermodynamics, high-resolution enthalpy profiles are computed from operando heat and voltage profiles, enabling to track and unravel redox variations during the cycling ageing. Collectively, this work shows that fiber optic sensors are essential tools for operando deciphering cell ageing and offer tremendous opportunities for academia and industry alike.
090511
The following article is Open access
Hyeongjun Choi, Dongjun Moon, Junmyoung Sheem, Jin Kyo Koo, Seungmin Hong, Seung-Min Oh and Young-Jun Kim
Manufacturing electrodes for lithium-ion batteries (LIBs) consists of making a slurry, coating the slurry onto a current collector, drying the slurry to remove the solvent, and calendaring the electrode. Cathodes for LIBs are fabricated by a wet process using a toxic chemical, N-methyl-2-pyrrolidone (NMP). However, it is preferable to use a dry process without toxic chemicals, and with fewer manufacturing operations, which saves money. However, the powder-mixing step of the dry process makes it difficult to ensure a uniform distribution of the carbonaceous conducting agents and binder used, which agglomerate in the dry mixed product. To solve this problem, we fabricate a composite of polytetrafluoroethylene (PTFE) and carbon black (CB) nanoparticles. The electrode fabricated using the PTFE/CB composite has a 98 wt% active material content and 3.8 g cc−1 of electrode density. An electrode produced by the conventional wet process using a polyvinylidene fluoride (PVDF) binder and NMP solvent has a 96 wt% active material content and an electrode density of 3.4 g cc−1. The dry-processed electrode has a higher volumetric capacity (760 mAh cc−1) as well as a higher discharge rate capability and cycle life than a conventional wet-processed electrode.
090512
The following article is Open access
Jason K. Ostanek, Mohammad Parhizi, Weisi Li, Gozdem Kilaz and K. R. Crompton
A high-resolution, 3D, computational fluid dynamics (CFD) model was developed and implemented for simulating the heat and gas generation during thermal runaway failure of an 18650 Li-ion battery cell. The model accounts for volumetric gas generation within the active material of the cell and for gas flow through the jellyroll, into the headspace regions, through the safety vent, and out into the surrounding air space. The simulation captures the key features of the oven test, including: self-heating from decomposition reactions, initial venting (i.e. blowdown), temperature decrease due to evaporative cooling, thermal runaway, a second venting event associated with thermal runaway, and cooldown. The highly detailed geometric model of the safety vent allowed for new insight into the physics of venting during thermal runaway. Secondary flows, including ring vortices, counter-rotating vortex pairs, and corner vortices, were found to increase the rate of mixing of the vented gases with the surrounding air. The simulation was compared to previously reported experimental results and found to have good qualitative agreement of jet flow direction. The present thermal abuse model forms the basis for future studies to consider the role of gas impingement heat transfer and gas combustion in full battery pack propagating failures.
Highlights
A 3D thermal abuse model was implemented for an 18650 li-ion cell oven test
Model includes gas generation from decomposition reactions and evaporation
Simulations show gas flow through the jellyroll, safety vent, and out of the cell
Spatial distribution of vented gases depends strongly on rate of gas generation
Turbulent flow structures increased the vent gas mixing rate with surrounding air
090513
Jianda Wang, Matthew Powell, Ryan Alcala, Christopher Fetrow, Xiao-Dong Zhou and Shuya Wei
Rechargeable Li-CO2 batteries have emerged as promising candidates for next generation batteries due to their low cost, high theoretical capacity, and ability to capture the greenhouse gas CO2. However, these batteries still face challenges such as slow reaction kinetic and short cycle performance due to the accumulation of discharge products. To address this issue, it is necessary to design and develop high efficiency electrocatalysts that can improve CO2 reduction reaction. In this study, we report the use of NiMn2O4 electrocatalysts combined with multiwall carbon nanotubes as a cathode material in the Li-CO2 batteries. This combination proved effective in decomposing discharge products and enhancing cycle performance. The battery shows stable discharge–charge cycles for at least 30 cycles with a high limited capacity of 1000 mAh g−1 at current density of 100 mA g−1. Furthermore, the battery with the NiMn2O4@CNT catalyst exhibits a reversible discharge capacity of 2636 mAh g−1. To gain a better understanding of the reaction mechanism of Li-CO2 batteries, spectroscopies and microscopies were employed to identify the chemical composition of the discharge products. This work paves a pathway to increase cycle performance in metal-CO2 batteries, which could have significant implications for energy storage and the reduction of greenhouse gas emissions.
090514
Jie Xiao, Yonglian Xiong, Pengju Lei, Ting Yi, Quanhui Hou, Yongsheng Fan, Chunsheng Li and Yan Sun
Accurately estimating the state of charge (SOC) is imperative for ensuring safe and dependable battery utilization. However, accurately calculating SOC for LiMn0.6Fe0.4PO4/LiNi0.5Co0.2Mn0.3O2 (LMFP/NCM) batteries can be challenging due to their two flat voltage platforms and significant temperature dependence. To improve estimation accuracy, a battery SOC estimation method based on a dual Kalman filter (DKF) was proposed. The adaptive unscented Kalman filter (AUKF) process starts with the introduction of Schmidt orthogonal transform, which is subsequently employed in the algorithm’s sampling point selection procedure to mitigate computational complexity. Moreover, the utilization of the multi-innovation theory serves to enhance the accuracy of algorithmic estimation. The extended Kalman filter is used to identify the parameters of the equivalent circuit model online while simultaneously carrying out battery SOC estimation. This approach mitigates the impact of variations in battery model parameters during charging and discharging processes. Under complex conditions, the algorithm’s average error is less than 0.53%, demonstrating its effectiveness in improving SOC estimation accuracy as evidenced by comparison between experiment and simulation results. It has reference significance for optimizing LMFP/NCM battery SOC estimation.

090515
The following article is Open access
Matthew Labbe and Douglas G. Ivey
Evaluating the electrochemical performance of catalysts towards the oxygen reduction and evolution reactions in zinc-air batteries is a routine process often conducted using a two-electrode cell. At the air electrode, a current collector is necessary if a carbon paper-based gas diffusion layer (GDL) is employed. The catalytic properties of the current collector may interfere with the studied catalyst on the GDL if flaws in cell design allow electrolyte contact to be made with the current collector. At the zinc electrode, highly alkaline electrolytes (e.g., KOH), with high surface tension, can easily climb up the electrode and accumulate at the interface between the cell and the surrounding atmosphere. An oxygen concentration cell is then enabled by the deposited electrolyte and the zinc electrode is rapidly corroded until failure, prematurely ending a long-term cycling test.
090516
Gayathri Peta, Hadas Alon-Yehezkel, Nagaprasad Reddy Samala, Shaul Bublil, Yuval Elias, Ilya Grinberg, Miryam Fayena-Greenstein and Doron Aurbach
Nanometric fillers are known to affect the electrochemical performance of polymer electrolytes. Here, nanowires and nanotubes of TiO2 with the same crystal structure are compared as additives to poly(ethylene oxide) based electrolytes for solid state sodium batteries. Electrochemical studies of symmetric cells with blocking and non-blocking electrodes examined the effects of the additive shapes on the bulk electrolyte and Na-electrolyte interface. Impedance spectroscopy was used as a major electroanalytical tool. To obtain a full perspective, all-solid-state batteries were evaluated. In galvanostatic measurements the filler shape effect is most noticeable at a high current density. TiO2 nanotubes improve the solid electrolyte behavior considerably more than titania nanowires. This effect is related mainly to the interface of the polymeric matrix with the electrodes.
090517
The following article is Open access
Zach J. Hoffman, Michael D. Galluzzo, Madeleine P. Gordon, Jeffrey J. Urban and Nitash P. Balsara
Concentrated solution theory has furthered our understanding of ion transport in electrolytes. This theory can be used to predict salt concentration profiles under an applied current if the transport properties of the electrolyte (conductivity (κ), restricted diffusion coefficient (D), and the cation transference number with respect to the solvent velocity (
)), and the thermodynamic factor (Tf) are known. In this work, we provide the first study comparing the predicted salt concentration profiles with measurements based on operando Raman spectroscopy. Concentration polarization is asymmetrical; the increase in salt concentration near the positive electrode is a factor of two greater than the decrease in salt concentration near the negative electrode. We find qualitative agreement between theory and experiment. Further work is needed to resolve the quantitative differences.
090518
The following article is Open access
Dominik V. Horváth, Valeria Nicolosi and Jonathan N. Coleman
Combining high-capacity electrodes with good rate performance is essential for maximising both energy and power density in Li-ion batteries. While much effort has been dedicated to increasing both capacity and rate performance, little consideration has been made as to how an increase in specific or volumetric capacity might directly affect rate performance. Here, we quantitatively examine the relationship between the volumetric capacity of Li-storing electrodes and their rate performance using graphite/boron-nitride composite electrodes with a range of compositions as a model system. The rate performance of these cells is evaluated by fitting capacity vs rate curves to a semi-empirical equation and extracting a characteristic charge/discharge time. As graphite content and so electrode capacity are increased, we observe a linear, threefold increase of this characteristic time, representing a significant degradation in rate performance. This shows that capacity and rate performance are anti-correlated, an observation is consistent with the predictions of a simple physical model which shows this effect to be associated with the RC charging time of the electrode. Using no adjustable parameters, we find excellent agreement between the model and our experimental data.
090519
The following article is Open access
Anudeep Mallarapu, Shriram Santhanagopalan, Wataru Uno, Yuta Kanai, Yohei Uemura, Ryosuke Yagi and Shuichi Uchikoga
Quantifying aging effects in lithium-ion cells with chemistries that have a flat open circuit potential is challenging. We implement a physics-based electrochemical model to track changes in the electrochemical impedance response of lithium titanate-based cells. Frequency domain equations of a pseudo two-dimensional model are made dimensionless, and the corresponding non-dimensional parameters are estimated using a Levenberg-Marquardt routine. The model weighs the relative contributions of changes in diffusion, ionic conduction within the electrolyte phase against solid phase electronic conduction towards cell aging. Solid-phase diffusion, charge transfer resistance and double layer capacitance at the solid-liquid interface are accounted for in the particle impedance. The estimation routine tracks dimensionless parameters using accelerated cycling data from full cells over 1000 cycles. The model can be deployed within a short time for state estimation using physics-based models without requiring prior knowledge of the battery chemistry, format, or capacity.
090520
The following article is Open access
Jesús I. Medina-Santos, Jesús Palma, Edgar Ventosa and Enrique Garcia-Quismondo
The Solid Electrolyte Interface (SEI) in lithium-ion batteries plays a critical role in key performance indicators such as cycle life and the significance of its ionic conductivity and electrically-protecting character. The SEI layer’s chemical composition and structure significantly influence its ionic conductivity, and various strategies exist to enhance its electrically-protecting character while maintaining adequate ionic conductivity. Herein, a Redox-Mediated Enhanced Coulometry method is presented, which enables evaluation of both protecting character and ionic conductivity of the SEI, which allows estimation of cycle life at various temperatures. The method is based on the electrochemical impedance spectroscopy (EIS) technique and coulombic efficiency measurements in the presence of redox mediators. The impact of electrolyte additives at different temperatures has been used to demonstrate the potential of the proposed method.

Highlights
090521
The following article is Open access
Yicheng Zhang, Glenn Teeter, Young Jin Kim, Kyusung Park, Anthony Burrell and Yeyoung Ha
Toward the development of high energy density and long lifetime batteries for behind-the-meter storage (BTMS) applications, Li- and Mn-rich layered oxide cathode (xLi2MnO3·(1-x)LiMeO2, Me = Ni, Mn, and etc., LMR-NM) and Li4Ti5O12 (LTO) anode system was examined. To mitigate the major degradation mechanisms at each electrode (i.e., loss of Li inventory (LLI) at the anode and transition metal dissolution and oxygen release at the cathode), two approaches were taken—prelithiating the LTO electrode and varying the electrolyte solvent compositions. The effect of prelithiation and electrolyte engineering on the long-term cycle performance of LMR-NM/LTO cells were systematically evaluated via electrochemical analyses and post-mortem characterizations. By using a prelithiated LTO anode and supplying additional Li to the system, the capacity retention of LMR-NM/LTO system was improved. The degree of enhancement was dependent on the types of electrolytes used, as their decomposition products determined the level of LLI. With increased capacity retention, however, the cathode was utilized to a greater extent, resulting in more severe loss of the cathode active material. Thus, all degradation mechanisms should be considered comprehensively when designing high performance LMR-NM/LTO cells to account for their complex interplay.
090522
Taihe Le, Pingli Mao, Wenyi Hu and Qichi Le
Mg–Sn–Ca alloys are promising candidates for Mg–air battery anodes. In this study, the influence of Sn/Ca mass ratio on the formation of the second phase, corrosion behavior and discharge performance of Mg-xSn-1Ca (x = 0.5, 1.0, 2.5, 4.0 wt%) alloys, has been investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD) and electrochemical characterizations. The results reveal that the CaMgSn phase forms in four Mg–xSn–1Ca alloys, the Mg2Ca phase precipitates in low Sn/Ca mass ratio alloys (Mg-0.5Sn-1Ca and Mg–1Sn–1Ca), and the Mg2Sn phase precipitates in the Mg-4Sn-1Ca alloy. Low Sn/Ca mass ratio alloys present better corrosion resistance than high Sn/Ca mass ratio alloys (Mg-2.5Sn-1Ca and Mg-4Sn-1Ca). The improvement in the corrosion resistance of the Mg2Ca phase is more than that of the Mg2Sn and CaMgSn phases. The highest average discharge voltage, anodic efficiency, power density, specific capacity, and specific energy of 1.188 V, 58.3%, 23.78 mW cm−2, 1225.5 mA h g−1, and 1389.8 mW h g−1, respectively, are found for the Mg-0.5Sn-1Ca alloy at an Sn/Ca mass ratio of 0.34, at a current density of 20 mA cm−2. This is attributed to better corrosion resistance and good electrochemical activity of the alloy. For the TX01 alloy, the current of discharge failure is calculated to be 93.6 mA.
090523
The following article is Open access
Andrew Weng, Everardo Olide, Iaroslav Kovalchuk, Jason B. Siegel and Anna Stefanopoulou
This work proposes a semi-empirical model for the SEI growth process during the early stages of lithium-ion battery formation cycling and aging. By combining a full-cell model which tracks half-cell equilibrium potentials, a zero-dimensional model of SEI growth kinetics, and a semi-empirical description of cell thickness expansion, the resulting model replicated experimental trends measured on a 2.5 Ah pouch cell, including the calculated first-cycle efficiency, measured cell thickness changes, and electrolyte reduction peaks during the first charge dQ/dV signal. This work also introduces an SEI growth boosting formalism that enables a unified description of SEI growth during both cycling and aging. This feature can enable future applications for modeling path-dependent aging over a cell’s life. The model further provides a homogenized representation of multiple SEI reactions enabling the study of both solvent and additive consumption during formation. This work bridges the gap between electrochemical descriptions of SEI growth and applications toward improving industrial battery manufacturing process control where battery formation is an essential but time-consuming final step. We envision that the formation model can be used to predict the impact of formation protocols and electrolyte systems on SEI passivation and resulting battery lifetime.
090524
The following article is Open access
Tobias Hofmann, Jacob Hamar, Marcel Rogge, Christoph Zoerr, Simon Erhard and Jan Philipp Schmidt
One of the most challenging tasks of modern battery management systems is the accurate state of health estimation. While physico-chemical models are accurate, they have high computational cost. Neural networks lack physical interpretability but are efficient. Physics-informed neural networks tackle the aforementioned shortcomings by combining the efficiency of neural networks with the accuracy of physico-chemical models. A physics-informed neural network is developed and evaluated against three different datasets: A pseudo-two-dimensional Newman model generates data at various state of health points. This dataset is fused with experimental data from laboratory measurements and vehicle field data to train a neural network in which it exploits correlation from internal modeled states to the measurable state of health. The resulting physics-informed neural network performs best with the synthetic dataset and achieves a root mean squared error below 2% at estimating the state of health. The root mean squared error stays within 3% for laboratory test data, with the lowest error observed for constant current discharge samples. The physics-informed neural network outperforms several other purely data-driven methods and proves its advantage. The inclusion of physico-chemical information from simulation increases accuracy and further enables broader application ranges.
090525
Lei Wang, Yubin He and Huolin L. Xin
Solid polymer electrolytes (SPEs) offer potential advantages over liquid electrolytes, including flexibility, safety, and processability. However, they suffer from low room-temperature ionic conductivity. Recently, it has been reported a poly(ethyl acrylate) based (polyEA) SPE, by incorporating 50 wt% of succinonitrile (SN) solid plasticizer, 30 wt% of lithium salt and 5 wt% of fluoroethylene carbonate additive, which achieves a high room-temperature ionic conductivity of 1.01 × 10−3 S cm−1 (Nat. Nanotechnol, 2022, 17, 768-776). This novel SPE exhibits stability against Li0 and anodic stability up to 4.9 V vs Li+/Li. However, the specific mechanism responsible for its high ionic conductivity remains elusive. In this work, by adjusting the weight ratio of SN in the SPE, a transition from Vogel-Fulcher-Tammann to Arrhenius ion-conducting behavior is observed. It is demonstrated that the addition of SN leads to the gradual decoupling of Li-ion from the polymer backbone and its coordination with SN, as revealed by 6Li solid-state nuclear magnetic resonance spectroscopy. As a result, Li-ion migration primarily occurs through SN rather than the segmental motion of the polymer backbone. Performances of the SPE in Cu||Li, Li||Li and a LiFePO4||Li pouch cells are shown to demonstrate the commercial viability of this SPE in Li0-anode solid-state batteries.
090526
Shota Tsujimoto, Changhee Lee, Yuto Miyahara, Kohei Miyazaki and Takeshi Abe
Non-graphitizable carbon allows reversible sodium-ion intercalation and hence enables stable and high-capacity sodium storage, making it a promising material for achieving long-term cycling stability in sodium-ion batteries (SIBs). This study investigated the interfacial reactions between various electrolytes and a non-graphitizable carbon electrode for their use in SIBs. The morphology and particle diameter of the non-graphitizable carbon, HC-2000, remained unchanged after heat treatment, indicating its stability. The X-ray diffraction pattern and Raman spectrum suggested a disordered structure of HC-2000 carbon. The interlayer spacing, Brunauer–Emmett–Teller specific surface area, and density were determined to be 0.37 nm, 5.8 m2 g−1, and 1.36 g cm−3, respectively. Electrochemical impedance spectroscopy analysis showed that the charge transfer resistances differed between the Na salts and other electrolytes. Therefore, the use of a large amount of NaF in the solid electrolyte interphase (SEI) resulted in high charge transfer resistances at the non-graphitizable electrodes. However, there were no apparent differences in the activation energy or reversible capacity. In summary, NaF obstructs the penetration pathway of sodium ions into non-graphitizable carbon, impacting the charge transfer resistance and rate stability of SIBs. Charge–discharge measurements revealed reversible capacities of 260–290 mAh g−1, and the rate performance varied depending on the electrolyte. Therefore, an SEI containing minimal inorganic species, such as NaF, is desirable for efficient sodium-ion insertion into non-graphitizable carbon.
090527
The following article is Open access
Tina Taskovic, Anu Adamson, Alison Clarke, Ethan D. Alter, Ahmed Eldesoky, Kevin L. Gering, Kenneth Tuul and J. R. Dahn
A common degradation product dimethyl-2,5-dioxahexane carboxylate (DMOHC) produced in Li-ion cell electrolytes after ageing is used here as an electrolyte solvent, allowing Li-ion cells to operate at high temperatures (70 °C and 85 °C) with excellent capacity retention and low impedance growth. Viscosity and conductivity values are reported for various DMOHC and diethyl-2,5-dioxahexane carboxylate (DEOHC) blends with dimethyl carbonate (DMC) and diethyl carbonate (DEC). Charge-discharge cycling data are reported for LiFePO4/graphite (LFP), Li[Ni0.5Mn0.3Co0.2]O2/graphite (NMC3.8 V, balanced for 3.8 V cut-off), Li[Ni0.6Mn0.4Co00]O2/graphite (NMC640, balanced for 4.1 V cut-off) and Li[Ni0.83Mn0.06Co0.11]O2/graphite (Ni83, balanced for 4.06 V cut-off) pouch cells at 70 °C and 85 °C. Pouch cells with DMOHC electrolyte have extraordinarily long lifetimes at 70 °C and 85 °C Pouch cells containing DMOHC-based electrolytes produce little to no gas compared to traditional ethylene carbonate (EC) based electrolytes. Cells taken apart after testing showed uniform negative electrode lithiation and no differences in the cell components were observed when using DMOHC electrolytes compared to EC. Lastly, micro X-ray fluorescence spectroscopy analysis was performed to probe the degree of transition metal deposition on negative electrodes of cycled cells. Very low levels of transition metals were found on the negative electrode even for cells tested at 85 °C. DMOHC is a co-solvent that can enable Li-ion batteries with exceptional high temperature lifetimes.
090528
Yu Yang, Jie Ding, Dezhi Shen and Tianyun Hao
State of charge (SOC) plays a crucial role in battery management systems, which is of paramount importance in safety of lithium-ion batteries. However, incorrect charging/discharging, electromagnetic interference, electrochemical rebound characteristics of the battery, or battery faults can lead to sudden and unexpected variations in SOC, posing hazards on systems with lithium-ion batteries. To achieve rapid and accurate tracking of such variations, this paper proposes a robust strong tracking filter based on optimal information fusion, which can address the issue of estimation accuracy degradation caused by the over-adjustment of the fading factor in traditional strong tracking filters, while maintaining strong tracking capability for SOC variations. The effectiveness of the proposed method has been demonstrated by discharge experiments and dynamic stress testing.
090529
Naoya Masuda, Kiyoshi Kobayashi, Futoshi Utsuno and Naoaki Kuwata
All-solid-state lithium-ion batteries are a promising next-generation technology because they have higher energy densities than their liquid-electrolyte counterparts. Recently, halogen-rich argyrodite, specifically Li5.4(PS4)(S0.4Cl1.0Br0.6), has been reported to show higher ionic conductivities than other sulfides with argyrodite structures and electrochemical stability against lithium metal. However, the stability of Li5.4(PS4)(S0.4Cl1.0Br0.6) against cathode active materials in all-solid-state batteries has not yet been evaluated. Herein, we report the electrochemical stability of Li5.4(PS4)(S0.4Cl1.0Br0.6) as a solid electrolyte in an all-solid-state battery. Li(Ni0.8Co0.1Mn0.1)O2 and lithium metal were used as the cathode and anode, respectively, and an enhancement in the discharge capacity was expected. The impedance of the battery was almost independent of the frequency above 106 Hz for 50 charge/discharge cycles. These findings are a result of the constant lithium-ion resistance of Li5.4(PS4)(S0.4Cl1.0Br0.6). X-ray diffraction analysis confirmed that no byproduct phase was formed in the cathode mixture over 50 cycles. These results demonstrate the high chemical stability of Li5.4(PS4)(S0.4Cl1.0Br0.6) against Li(Ni0.8Co0.1Mn0.1)O2, thereby broadening the design scope of electrolyte materials for all-solid-state lithium-ion batteries with high performance and stability.

090530
The following article is Open access
A. Eldesoky, N. Kowalski, Haoqi Ni, E. R. Logan, E. Zsoldos, A. Dutta, N. Zhang and J. R. Dahn
The impact of electrolyte, Li excess, NMC blending, and cycling conditions on the performance of Li1+xMn2-xO4 (LMO)/Artificial Graphite (AG) cells was studied using ultra-high precision coulometry (UHPC), X-ray fluorescence (XRF), and isothermal microcalorimetry (IMC). Decreasing the Li excess resulted in severe capacity fade which was greatly improved by blending LMO with NMC622. The known synergy between NMC and LMO is electrolyte-dependant and was more significant at elevated temperatures. We showed with XRF that Mn deposition on the negative electrode occurs primarily during the early cycles and is reduced by increasing the Li excess in LMO or by blending with NMC622. IMC experiments demonstrates a correlation between parasitic heat flow and Mn loading on the negative electrode and gas generation. Finally, LiFSI co-salts were examined to suppress Al corrosion while retaining the beneficial role of LiFSI in improving cell performance.
090531
Toshikatsu Kojima, Mitsunori Kitta and Riki Kataoka
Spinel-type sodium titanium oxide, Na3LiTi5O12 (NTO) has a structure analogous to that of Li4Ti5O12 (LTO) and is a promising anode material for sodium-ion batteries exhibiting good cyclability. However, the synthesis of NTO using LTO is a tedious process and requires more than nine iterated procedures, which involves the reductive insertion of Na+ in a glovebox, followed by oxidation using water, and subsequent extraction of Li+. Therefore, in this study, a efficient method was developed for the conversion of LTO to NTO. The conversion ratio of sodiated LTO to NTO during water oxidation was determined from the quantity of Li+ released into water, which was evaluated using ion chromatography. The results revealed that the conversion ratio was approximately 53 mol% at 273 K but decreased to 45 mol% at 303 K confirming its temperature dependence. Moreover, the sodiation of LTO could be accelerated via stirring, ultrasonication, and heating to 323 K. NTO was successfully produced via five treatment cycles using a method without using the glovebox. The half-cell employing the obtained NTO afforded a capacity of 125 mA h g−1, and stable cyclability for up to 200 cycles, with a retention ratio of 97.6% and a coulombic efficiency of 99.8%.
090532
The following article is Open access
Yanli Zhang, Wenjuan Zhang, Jiakun Zhou, Xiaoning Li, Wenzhang Zhou, Yanting Xie, Jing Mao and Kehua Dai
Spinel LiMn2O4 (LMO) is a cathode material that features 3D Li+ diffusion channels, and it offers a range of benefits including low cost, non-toxicity, environmental friendliness, high safety, and excellent rate performance. Consequently, it has become a popular cathode material for lithium-ion batteries, having gained practical application. However, the cycling performance of LMO is still limited by problems such as Jahn-Teller distortion and Mn dissolution. In recent years, researchers have proposed various preparation and modification methods to address these problems and achieve wider commercialization of LMO cathode materials. This paper introduces the spinel structure of LMO and its degradation mechanisms, listing several common methods for synthesizing LMO cathode materials and modification approaches aimed at improving cyclic stability.

090533
Udita Bhattacharjee, Madhushri Bhar, Shuvajit Ghosh, Subhajit Bhowmik and Surendra K. Martha
Lithium-ion capacitors (LICs) are hybrid capacitors that target pushing the energy limits of conventional supercapacitors by incorporating a lithium-ion battery (LIB)-type electrode without compromising much on the power density and cycle life of capacitors. Herein, a LIC is assembled using an ordered porous carbon cathode derived from the recycled polymer separator of spent LIBs and recycled graphite anode from the same source. The carbon-rich polymer is thermally stabilized and carbonized to utilize its porosity for ion storage and ordered matrix for better electronic conduction. The cathode half-cell delivers a capacitance of ∼100 F g−1 till 1000 cycles at 1 A g−1. In contrast, the anode half-cell delivers a capacity of 130 mAh g−1 under similar conditions. The assembled LIC provides an energy density of 129 Wh kg−1 at a power density of 275 W kg−1 and 54 Wh kg−1 at a high-power density of 13750 W kg−1. The LIC cycles with >70% capacitance retention till 6000 cycles. Further, the ion-storage mechanism of the LICs as well as their capacitive and diffusion-type contribution, is studied. The self-discharge and leakage current tests were performed in the cells to understand their practical feasibility.
090534
Otto von Kessel, Tobias Hoehl, Philipp Heugel, Felix Brauchle, Dragoljub Vrankovic and Kai Peter Birke
The mechanical changes in active materials with large volume expansion such as silicon and nickel not only affect the electrochemical performance of modern batteries but also pose a great challenge to their mechanical design due to the pressure increase during operation. In this study, we show that the large expansion and consequently changing mechanical properties of silicon and nickel strongly affect the electrochemical and mechanical performance. A multi-scale electrochemical model is developed, parameterized, and validated for a pouch cell with a SiOx-graphite anode (22 wt% SiOx) and an NMC∣811 cathode. Mechanical parameters such as expansion and compressive properties are determined experimentally using an in-house-developed high-precision cell press and electrode dilatometer, thus parameterizing a semi-empirical mechanical model. We employ a new characterization technique to measure mechanical changes in the cell in-operando and propose a phenomenological parameterization where physical modeling is not yet sufficient. Through electrode porosity, we show that mechanical and electrochemical performance are interdependent, as the latter is reduced upon expansion and pressure development. On the one hand, the active material of the anode seems to expand into the pores at increased pressure, and on the other hand, the mechanical deformation of the cell components can no longer be neglected.
090535
Pappu Naskar, Shubhrajyoti Mondal, Biplab Biswas, Sourav Laha and Anjan Banerjee
A successful solar energy storage is accomplished in a 5 V/5 mAh rated Na-ion battery, which is customized by series connection of three 1.8 V unit cells. The unit cell is constructed with open framework structured Na2Co0.5Ni0.5Fe(CN)6 positive and Natrium Super Ionic CONductor (NaSICON) type NaTi2(PO4)3 negative electrodes in 1 M Na2SO4-SiO2 hydrogel electrolyte. Both positive and negative active materials demonstrate Faradaic charge storage mechanism with appreciable diffusion coefficients, such as 5.17 × 10−15 and 1.13
10−15, respectively. The Na2Co0.5Ni0.5Fe(CN)6//NaTi2(PO4)3 full cell depicts a specific capacity of 48 mAh g−1 (@ 100 mA g−1), an energy density of 95.68 Wh kg−1 (@ 259.96 W kg−1) and a power density of 779.75 W kg−1 (@ 54.36 Wh kg−1). The cell also exhibits an excellent durability, i.e., 93% capacity retention with 99% Columbic efficiency at 200 mA g−1 upon 1000 cycles. However, the 5 V battery is performance tested under solar-charging cum constant-load-discharging experiment for one-month, and the device describes 85% capacity retention over the period. The good power capability and cycle life with moderate energy density make this battery chemistry suitable for solar energy storage applications.
090536
Shiqi Zhou
Classical density functional theory is used to study the capacitance enhancing issue of electrical double-layer using aqueous-like electrolyte and ionic liquid+solvent mixture (ILSM) as supporting electrolyte, respectively. The polar organic solvent and water-like solvent are described by an electric dipole dimer model. This study focuses on capacitance enhancing of counter-ion sized electrode pore (CISEP) relative to large pore capacitance and relation with electrode voltage applied, counter-ion relative size, solvent weight percentage in the bulk and its polarity depicted by electric dipole moment.
090537
The following article is Open access
Lei Zhao, Xuzhi Du, Zhigang Yang, Chao Xia, Jinwei Xue, Muhammad Jahidul Hoque, Wuchen Fu, Xiao Yan and Nenad Miljkovic
Lithium-ion (Li-ion) batteries find wide application across various domains, ranging from portable electronics to electric vehicles (EVs). Reliable online estimation of the battery’s state of health (SOH) is crucial to ensure safe and economical operation of battery-powered devices. Here, we developed three deep learning models to investigate their potential for online SOH estimation using partial and random charging data segments (voltage and charging capacity). The models employed were developed from the feed-forward neural network (FNN), the convolutional neural network (CNN) and the long short-term memory (LSTM) neural network, respectively. We show that the proposed deep learning frameworks can provide flexible and reliable online SOH estimation. Particularly, the LSTM-based estimation model exhibits superior performance across the test set in both direct learning and transfer learning scenarios, while the CNN and FNN-based models show slightly diminished performance, especially in the complex transfer learning scenario. The LSTM-based model achieves a maximum estimation error of 1.53% and 2.19% in the direct learning and transfer learning scenarios, respectively, with an average error as low as 0.28% and 0.30%. Our work highlights the potential for conducting online SOH estimation throughout the entire life cycle of Li-ion batteries based on partial and random charging data segments.
090538
The following article is Open access
Haeseong Jang, Ivana Hasa, Hyunchul Kim, Yoon Hwa, Young-Woon Byeon, Robert Kostecki and Haegyeom Kim
This study aims to develop high-capacity hard carbon anode materials for alkali-ion batteries by controlling the microstructures of non-graphitic hard carbon through an annealing protocol and investigating the effects on the alkali-ion storage mechanisms using physical, chemical, and electrochemical analytical techniques. The hard carbon materials were synthesized at temperatures ranging from 900 °C to 1600 °C. Those synthesized at 1100 °C with high surface area and abundant defects exhibited the highest reversible capacity in Li- and K-ion systems, with the storage dominated by surface-adsorption mechanisms. In contrast, the hard carbon compounds prepared at 1400 °C with numerous curve-featured pores delivered the highest reversible capacity in the Na-ion system, indicating that these pores are the preferred Na-ion storage sites, particularly in low-voltage plateau regions. This study provides a comprehensive understanding of the relationship between microstructures and alkali-ion storage mechanisms in non-graphitic hard carbon and highlights the importance of tailoring the microstructures of hard carbon to achieve high specific capacity for the desired alkali-ion species.
090539
Meng Hu and Shaodian Shen
The requirement for high-power performance of secondary batteries suffering from inherent sluggish charge transfer kinetics is urgent for the expanding energy storage and conversion applications such as electric vehicles. A successful combination of high-power supercapacitors with high-energy secondary batteries in one energy storage device will meet the needs of both high power and energy density. We study the electrochemical behaviors of alternately stacked super-capacitive [Co4Al(OH)10]NO3 and [Ni4Al(OH)10]NO3 layered double hydroxide (LDH) electrodes. By cyclic voltammetry studies, the sandwich of [Co4Al(OH)10]NO3 lDH between [Ni4Al(OH)10]NO3 LDH and the Pt current collector results in the current amplification of the oxidation or reduction peaks to 4∼35 times. By galvanostatic charging/discharging, the 3-stacked Ni–Al|Co–Al|Ni–Al LDH electrode behaves better than the Co–Al|Ni–Al|Co–Al LDH electrode, exhibiting a maximal capacity, 338.1 mAh·g−1 under a current density of 1000 mA·g−1 and maintaining 288.6 mAh·g−1 within 400 cycles. It also has a much lower liquid-solid interface capacitor resistance and lower self-discharge. These results suggest that stacking in a suitable sequence contributes to high electrode performances, providing a strategy for producing energy storage and conversion devices. A synergetic charge transfer for the combination of Ni–Al and Co–Al LDH suggests that Co–Al LDH outstands as a bridge, accelerating the transfer of electrons.

Highlights
Construction of sandwiched Ni-Al LDH|Co-Al LDH|Pt multi-layer modified electrode.
Amplification of oxidization and reduction currents of Ni-Al LDH up to 4∼35 times.
Excellent performances of 3-stacked heterostructured Ni-Al|Co-Al|Ni-Al electrode.
Proposing a synergetic charge transfer for the supercapacitor-battery combination.
090540
The following article is Open access
Anmol Jnawali, Matt D. R. Kok, Muthu Krishna, Mina Abedi Varnosfaderani, Daniel J. L. Brett and Paul R. Shearing
Lithium-ion (Li-ion) batteries have undergone a multitude of improvements and achieved a high level of technological maturity. To further optimise cell performance, an understanding of the failure mechanisms is important. Forty-eight state-of-the-art cylindrical cells in the 21700 format, suitable for electric vehicles, are studied at the beginning-of-life (BOL) and end-of-life (EOL) by X-ray computed tomography (X-ray CT) and image analysis. The results indicate that shifting current collecting tabs closer to the centre of the cell and including a mandrel is likely to supress the propagation of capacity depleting deformations. It is recommended that manufacturers also try to improve cell assembly processes to form a more uniformly circular jelly roll and use tapered electrodes to minimise the nucleation of deformations.
090541
Baicheng Liu, Yonghong Xu, Hongguang Zhang, Jian Zhang, Fubin Yang, Yan Wang, Hailong Yang, Zhuxian Liu and Hao Zheng
With the rise of new energy vehicles, supercapacitors (SCs) have been used as energy storage components for new energy vehicles due to their high-power density and good low-temperature performance. Accurate modeling and state of charge estimation of SC can ensure the safe operation of new energy vehicles. In order to explore the low-temperature performance of supercapacitors, this paper proposes a dual ZARC fractional-order circuit model to simulate the dynamic characteristics of SC. Using adaptive genetic algorithm for SC parameter identification, the model terminal voltage error is less than 6.5 mV. In addition, the SOC of SC at different temperatures and working conditions is estimated by using the fractional-order particle filter (FOPF) method and compared with the fractional-order extended Kalman filter (FOEKF). The experimental results show that the FOPF method has high estimation accuracy and robustness. Under the temperature of minus 40 °C, the maximum mean absolute error and maximum root-mean-square deviation of SOC estimation under different working conditions are less than 2%, showing good low-temperature performance.
Highlights
A fractional-order particle filter algorithm for estimating the SOC of supercapacitor is proposed.
Adaptive genetic algorithm is used to identify the model parameters.
The impact of low temperature on the accuracy of SOC estimation was studied.
The accuracy and robustness of the algorithm are verified using experimental data.
090542
The following article is Open access
Ben Dlugatch, Janina Drews, Ran Attias, Bar Gavriel, Adar Ambar, Timo Danner, Arnulf Latz and Doron Aurbach
One of the major issues in developing electrolyte solutions for rechargeable magnesium batteries is understanding the positive effect of chloride anions on Mg deposition-dissolution processes on the anode side, as well as intercalation-deintercalation of Mg2+ ions on the cathode side. Our previous results suggested that Cl− ions are adsorbed on the surface of Mg anodes and Chevrel phase MgxMo6S8 cathodes. This creates a surface add-layer that reduces the activation energy for the interfacial Mg ions transportation and related charge transfer, as well as promotes the transport of Mg2+ from the solution phase to the Mg anode surface and into the cathodes’ host materials. Here, this work further examines the effect of adding chlorides to the state-of-the-art Mg[B(HFIP)4]2/DME electrolyte solution, specifically focusing on reversible magnesium deposition, as well as the performance of Mg cells with benchmark Chevrel phase cathodes. It was observed that the presence of chlorides in these solutions facilitates both Mg deposition, and Mg2+ ions intercalation, whereby this effect is more pronounced as the purity level of the solution is lowered.
090543
The following article is Open access
Richard Bertram Church, Haining Gao, Betar M. Gallant and A. John Hart
To meet the growing performance demands for personal electronics and electric vehicles the energy density of lithium-ion batteries can be increased by incorporating thicker electrodes. We present thick “honeycomb” electrodes based on patterned, vertically aligned carbon nanotubes (CNTs) on Cu foils. Thick electrodes are created by Si deposition on >100 μm tall honeycomb patterned CNTs. Si-CNT electrodes are cycled in half-cells, demonstrating electronic connection between the Si and Cu foil via the aligned CNTs. For ~4.7 mAh cm−2 capacity the honeycomb patterning improves capacity retention (78%) over 30 cycles compared to non-patterned electrodes (58%). We attribute this improvement to the honeycomb’s ability to accommodate Si expansion, thereby reducing cracking that causes active material loss and solid electrolyte interphase instability, and to provide pathways for Li-ion transport into the electrode. The Si-CNT electrode capacity is further increased to 20 mAh cm−2 by increasing the Si loading. Finally, a fluoroethylene carbonate containing electrolyte is used to increase cell lifetime. Here, the honeycomb electrodes have a higher areal (~10.2 mAh cm−2) and retained (65%) capacity over 180 cycles, and exhibit superior rate performance to their non-patterned counterparts. Our work demonstrates the role of patterning in enabling aligned CNTs as a robust template for thick battery electrodes.
090544
The following article is Open access
Rashmi Tripathi, Göktug Yesilbas, Xaver Lamprecht, Pranay Gandharapu, Aliaksandr S. Bandarenka, Rajiv O. Dusane and Amartya Mukhopadhyay
The volume expansion/contraction of Si-based anodes during electrochemical lithiation/delithiation cycles causes a loss in mechanical integrity and accrued instability of the solid electrolyte interphase (SEI) layer, culminating into capacity fade. Electrolyte additives like fluoroethylene carbonate (FEC) improve SEI stability, but the associated causes still under debate. This work reveals some of the roles of FEC via post-mortem observations/analyses, operando stress measurements and a comprehensive study of the impedance associated with the formation/evolution of SEI during lithiation/delithiation. Usage of 10 vol.% FEC as electrolyte additive leads to significant improvements in cyclic stability, Coulombic efficiency and facilitates smoother/compact/crack-free surface/SEI, in contrast to the cracked/pitted/uneven surface upon non-usage of FEC. Operando stress measurements during SEI formation reveal compressive stress development, followed by loss in mechanical integrity, upon non-usage of electrolyte additive, in contrast to insignificant stress development associated with SEI formation upon usage of FEC. The EIS model proposed here facilitates good fit with the impedance data at all states-of-charges, with the SEI resistance and capacitance exhibiting expected variations with cycling and the SEI resistance progressively decreasing with cycle number in the presence of FEC. By contrast, in the absence of FEC, severe fluctuations observed with the SEI resistance and capacitance indicate instability.
Corrosion Science and Technology
091501
The following article is Open access
B. Malki, I. Guillotte and B. Baroux
This paper presents a novel method for deriving metastable Pourbaix diagrams of Fe-Cr alloys using Density Functional Theory calculations, with the objective of providing a more comprehensive understanding of the thermodynamic equilibria within passive films, considering the metallurgical characteristics of the alloys and the electrochemical polarization conditions. By using advanced numerical tools and optimization algorithms provided by the Materials Project Database, we have developed an approach that incorporates nonequilibrium effects as a corrective factor for the chemical equilibria observed in passive films. Our findings highlight the significant role of nucleation conditions, particularly for the Cr2O3 oxide, in stabilizing the inner layers of the passive films. Lastly, the method was used to investigate the impact of pulsed polarization conditions on AISI 304 stainless steel and proposed a reaction scheme elucidating the enhanced corrosion protective properties of the passive film.
091502
Isao Nakatsugawa, Koji Yamada, Tomoko Yamashita, Takashi Nishikawa, Yasuhito Taniguchi and Yasumasa Chino
Three different extruded Mg–Al–Zn–Ca–Mn magnesium alloys with varying alloying elements and a diecast AZ91D alloy were exposed to two coastal environments for five years. Under unsheltered exposure, Mg–Al type layered double hydroxide was primarily formed, and the mass loss corrosion rate was decreased with increasing Al content in the alloys. Under sheltered exposure, magnesium hydroxy carbonate was the main corrosion product. Additionally, Mg alloys with high Al content tended to exhibit localized corrosion. Furthermore, the negative impact of Ca addition on atmospheric corrosion occurred when the alloys were exposed under sheltered conditions.
091503
The following article is Open access
Isuri N. Dammulla and Greg M. Swain
The spontaneous formation of a diazonium molecular adlayer on the exposed fibers of a carbon fiber reinforced polymer (CFRP) composite was investigated as a surface treatment. The purpose of the surface treatment is to reduce the extent of galvanic corrosion on a trivalent chromium process (TCP) conversion-coated aluminum alloy when the two materials are mechanically joined as is common in aircraft structures. The adlayer functions to reduce the rate of dissolved oxygen reduction on the more noble carbon thereby reducing the rate of galvanic corrosion on the more active metal alloy. The formation of the adlayer (4-nitrophenyl (NP), 4-nitroazobenzene (NAB), or 2-fluorene diazonium tetrafluoroborate (FL)) was achieved by immersing the CFRP composite specimen in a solution of 5 mM diazonium salt dissolved in acetonitrile for a specified time (1–24 h) under open circuit conditions (so-called spontaneous deposition). Cyclic voltammetry (CFRP composite) and rotating disk voltammetry (glassy carbon) were used to investigate the oxygen reduction reaction kinetics in naturally aerated 0.5 M Na2SO4 (pH 5–6). The oxygen reduction reaction current was suppressed by greater than 90% by the NP and NAB adlayers and 80% by the FL adlayer. The surface treatment (24 h immersion) with NAB significantly reduced the galvanic corrosion damage on TCP conversion-coated aluminum alloy during a 14-day continuous neutral salt spray (NSS) exposure. The mass loss (mg/cm2) and corrosion intensity (g/m2y) were reduced by over 10×. The spontaneously formed NAB adlayers are stable during the salt-spray exposure and provide better inhibition of galvanic corrosion on the aluminum alloy and resistance to carbon corrosion than do NAB adlayers formed by an electrochemically assisted process reported on previously.
091504
Weidong Liu, Shun Li, Yonghua Zhao, Xiaoming Yue, Jingxin Su and Zhiping Wang
Electrochemical machining (ECM) is an essential non-traditional industrial shaping technology. An in-depth understanding of ECM anodic dissolution is fundamentally important for process parameter design and optimization. However, the existing electrochemical setups face challenges in achieving efficient analysis of these processes. In this work, a new flow cell has been developed via simulation-based design and 3D printing that demonstrates comprehensive advantages in terms of improved electric and flow conditions, measurement technique versatility, and production simplicity at low cost. Simulations are performed to reveal particular characteristics of the proposed cell in terms of physical distributions and to determine its key dimensions with high efficiency. The stereo lithography technique is used to realize the complex design and fabricate the proposed flow cell, thus ensuring ease of accessibility. Furthermore, the effectiveness of the developed cell is verified experimentally by examining the anodic behavior of typical metals in common ECM electrolytes, using Fe and SS304 stainless steel as examples. Test results show that information on the polarization behavior, current efficiency, anodic interface structure, and surface finish can be obtained conveniently and the results agree with previous findings, demonstrating the potential of the developed cell to perform high throughput tests to study ECM fundamentals.
091505
The following article is Open access
C. S. Witharamage, A. A. Darwish, J. Christudasjustus, J. Soltis and R. K. Gupta
The time-dependent corrosion behavior of pure aluminum (Al) in a chloride-containing environment was investigated using various electrochemical and characterization techniques for up to 336 h. Transmission electron microscopic and secondary ion mass spectroscopic analysis revealed the continuous dissolution of the surface film over the immersion time. In the meantime, the increasing passive oxide thickness resulted in the surface film resistance enhancement over the immersion time, as indicated by the electrochemical impedance spectroscopic analysis. The electrochemical noise measurements showed an increase in the corrosion kinetics with immersion time until 60 h because of the accelerated localized corrosion in the early stage of immersion. However, an inhibition in corrosion kinetics occurred after longer immersion times due to corrosion product deposition inside the pit.
Electrochemical/Electroless Deposition
092501
The following article is Open access
Shuhua Shan, Mihir N. Parekh, Rong Kou, Donghai Wang and Christopher D. Rahn
The cycle life and power density of Zn metal batteries depend on the anode electrodeposition morphology, including the formation of metal dendrites, and impedance, respectively. This paper investigates the influence of aqueous ZnSO4 electrolyte convection through a copper mesh anode on Zn electrodeposition morphology and current densities. Electrochemical experiments in a specially designed flow-through cell with a Zn metal cathode reveal that the electrolyte flow from the cathode through the anode improves Zn deposition morphology and reduces impedance at concentrations ranging from 0.01 to 1 mol l−1. Small flow rates at millimeters per second double the current densities. The electrodeposition morphology and current density are positively impacted at Peclet number larger than 1. At these flow rates, the Zn plating is more smooth, compact, uniformly deposited around the wire, and dense than that in the stagnant electrolyte. Zn-Cu asymmetric cell cycling tests at 50 mA cm−2 show that flow-through electrolyte can significantly increase the cell lifespan from 18 cycles in static electrolyte to 1300 cycles at a flow rate of 0.5 mm s−1. Numerical analysis illustrates that the flow-through electrolyte replenishes consumed zinc ions at the electrode surface and suppresses dendrite growth by maintaining a uniform current density distribution.
092502
Jiakang Qu, Xiang Chen, Hongwei Xie, Yanyang Guo, Dihua Wang and Huayi Yin
Electrochemically splitting sulfides to metals and sulfur gas is a promising clean method to reduce energy consumption and environmental burden. Anode electrolysis has been proven to break metal-sulfur bonds at the anode in molten salts, but the electrolysis of complex sulfides has not been investigated. Herein, the selective extraction of Fe, Cu and S in copper matte (the mixture of FeS and Cu2S) by anode electrolysis was thoroughly studied by both thermodynamics and electrochemical tests. The FeS component was preferentially oxidized from copper matte on the anode while releasing sulfur gas, and the Fe powder as the main product was first collected from the cathode and then Cu was obtained. During potentiostatic electrolysis of copper matte on the anode, the content of Fe element was reduced from 49.1% to 18.6%, and the content of Cu element was enriched from 1.8% to 41.2%, showing the potential for not only achieving the clean sulfide electrochemical metallurgy but also effective separation. Thus, anode electrolysis could be applied to extract various complex sulfide ores.

Highlights
Fe and Cu are selectively extracted from copper matter by anode electrolysis with a current efficiency of above 85%;
FeS was preferentially oxidized and then Cu2S was oxidized;
The content of Fe element was reduced from 49.1% to 18.6%, and the content of Cu element was enriched from 1.8% to 41.2%
A modified up-down electrolysis structure was designed.
092503
Bingbing Li, Kamran Dastafkan, Yu Shen, Lu Wang, Yi Ma, Zenglin Wang and Chuan Zhao
The application of advanced high-frequency (5 G) requires a low-profile Cu foil to reduce the high-speed signal loss due to skin effect. However, the adhesion of electroless copper film on the smooth surface of polyimides (PI) remains a challenge. Here, a two-step composite modification method, consisting of TiO2 photocatalysis and Na2S2O8 photooxidation treatment, is successfully applied to induce a high adhesion strength of electroless copper film on the smooth PI surface. To meet the requirements of the flexible electronics, the average surface roughness of the PI film is increased from 4.2 to 11.5 nm through optimizing the modification. Whereas the surface contact angle decreases from the original 76.9° to 18.7° and the adhesion strength between the electroless copper film and PI film is increased from 0 to 0.90 KN m−1. Spectroscopic investigations reveal that the amide bonds on the surface PI get oxidized by radicals, while an abundant –COOH and –NH2 groups form. The high oxidation potential, strong stability of the sulfate anion radicals, as along with their increased concentration in the treatment solution are contributed to the extraordinary modification performance. Therefore, the TiO2 photocatalysis and Na2S2O8 photooxidation composite treatment is an effective and environmentally friendly method for surface modification of PI films.
092504
Atiqah Binti Jasni and Sachio Yoshihara
Pyrimidine derivatives, for example, 2,4-pyrimidinedione (uracil), 1-methyluracil and 5-methyluracil (thymine) can bind with metal ions in alkaline solution. 5-methyluracil (thymine) as complexing agent in electroplating solution has not been investigated due to low solubility in water. The aims of this study were to determine the potential of 5-methyluracil (thymine) as complexing agent for cyanide-free silver electroplating solution. The influence of complexing agent and polyethyleneimine on the silver electrodeposition reaction were studied. Several methods which are electrochemical quartz crystal microbalance (EQCM) and electrochemical impedance spectroscopy (EIS) have been used to study the electrochemical behavior of cyanide-free silver electroplating solution. The surface morphology and brightness of silver deposits obtained from each cyanide-free silver electroplating solution were evaluated. A semi-bright deposit was obtained from thymine and uracil-complexing silver solution while matte deposit from 5,5-dimethylhydantoin-complexing silver solution. A bright silver deposit could be obtained in the presence of polyethyleneimine. The reduction current value decreases as the amount of polyethyleneimine added increases due to inhibition effect on the silver electrodeposition reaction. The results of electrochemical quartz crystal microbalance measurement showed that the addition of polyethyleneimine in thymine-complexing silver solution does not significantly affect the resonance frequency change.
092505
Shuna Liu, Ben Yang, Anran Zuo and Yongming Tang
Ti/SnO2-Sb/PbO2 anodes were electrodeposited from methanesulfonate-based baths, and the effect of dopants such as PVP and Fe on the surface morphology, phase composition, electrocatalytic activity and stability was investigated. It is revealed that the inclusion of Fe effectively enhances the stability of PbO2 anode, while PVP can significantly improve its electrocatalytic activity. The Fe,PVP-codoped anode, Ti/SnO2-Sb/Fe-PVP-PbO2, exhibits the higher stability and electrocatalytic activity compared to the respective inclusion of Fe and PVP. The gradation efficiency of methyl orange (MO) on the Ti/SnO2-Sb/Fe-PVP-PbO2 anode is affected by the applied current density and the initial MO concentration. During degradation, the azo structure of MO is firstly cleaved, resulting in the rapid decolorization of solution. Demethylated MO and the anion of sulfanilic acid are detected as intermediates, and thus a plausible pathway of MO degradation is proposed.
092506
Wei Han, Xiaohui Lan, Yongqiang Zhang, Rugeng Liu, Meng Zhang, Ji Wang, Yang Sun and Mei Li
092507
Mohd. Sufiyan Khan, Anwesha Mukherjee, L. Shakila, V. Arunkumar and R. Kumaresan
The aim of the present study was to prepare ZrFe2 and ZrFe1.8Ni0.2 intermetallic compounds by FFC Cambridge process. The intermetallic compounds were prepared directly from the mixed oxide precursors, namely ZrO2-Fe2O3 and ZrO2-Fe2O3-NiO, respectively. Electrochemical de-oxidation experiments were carried out with mixed oxide pellet cathode and HD graphite anode by applying a constant cell voltage of 3.1 V in CaCl2 melt at 900 oC. The electrochemical behaviour of oxides was studied by cyclic voltammetry using metallic cavity electrodes (MCEs). The electrolysis was carried out for different durations of time to understand the mechanistic pathway of reduction of ZrO2-Fe2O3. The electro-reduced products were characterized by X-ray diffraction (XRD) technique, scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS). The reduction intermediates involved Fe, CaZrO3, calcia stabilised zirconia (CSZ), Fe23Zr6, Zr6Fe3O and Zr2Fe. Single cubic C15 phase of ZrFe2 was obtained in 48 h electrolysis product. ZrFe1.8Ni0.2 was also electrochemically synthesized from its oxide precursors viz. ZrO2, Fe2O3 and NiO. Apart from ZrFe1.8Ni0.2 phase, the electro-reduced products had a Zr2Ni phase even after 72 h of electrolysis.
092508
The following article is Open access
Ryutaro Miura, Ryusuke Yuasa, Tsutomu Shinagawa, Kazuhiro Fukami and Kuniaki Murase
The direct or indirect effects of two different copper(II)-lactate complex species, Cu(H–1L)L– and Cu(H–1L)22–, on the orientation and electrical properties of Cu2O electrodeposits were examined, where L– = CH3CH(OH)COO– and H–1L2– = CH3CH(O–)COO–. To investigate the relationships between the copper(II)-lactate complex species and several properties of Cu2O, a set of Cu2O layers was electrodeposited from thermodynamically well-stabilized electrolytes of different pHs with unified overpotentials. The Cu2O layers obtained at pH <9.5 had the 〈100〉 preferential orientation, whereas the orientation changed to the 〈111〉 preferential orientation at pH >9.5. In addition, marked differences were observed in the resistivity and carrier density of Cu2O layers bordering pH 9.5, indicating the presence of a strong relationship between copper(II)-lactate complexes and these crystallographic or electrical properties. In terms of the cathodic reactivity of copper(II)-lactate complexes and changes in local pH in the vicinity of the cathode upon electrodeposition, we suggest that the two copper(II)-lactate complexes directly affected the electrical properties of Cu2O and indirectly affected its crystallographic orientation.
092509
The following article is Open access
Shoma Tchorap-Yamamoto, Yuta Suzuki, Seiya Tanaka, Hidekazu Kobatake and Takuya Goto
The conversion of CO2 to solid carbon by the electrochemical method is an attractive process as a CO2 recycling technology, but the electrolyte has been limited to high-temperature molten salts. In this study, the electrodeposition of solid carbon from CO2 on an Ag substrate in triethylpentylphosphonium bis(trifluoromethanesulfonyl)imide at room temperature and 1 atm CO2 atmosphere was investigated. Cyclic voltammetry with multiple cycles revealed that the three potential steps causing reduction, oxidation, and reduction current are important for the carbon electrodeposition from CO2. Based on the cyclic voltammogram, potentiostatic electrolysis was performed in the three potential steps. Consequently, the Ag substrate was covered with a black film because of the electrodeposited solid carbon. Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy revealed that the deposits were composed of the electrodeposited solid carbon and nanometer-size silver particles coming from the Ag substrate. From the experimental results, we propose a model of the electrochemical formation mechanism of solid carbon from CO2 on the Ag substrate. This study shows that the electrochemical method has the potential to convert CO2 into valuable carbonaceous materials with optimized electrochemical parameters, even at room temperature, and that this technique will contribute to developing a carbon-circulation society.
092510
Kristin Partanen, Dianne S. Lee, Adekunle Omoboye, Kevin McEleney, Rebecca X. Y. Chen and Zhe She
Effectively detecting bacteria in the environment is crucial for researchers to make informed decisions about the safety of public areas, such as lakes. This led to an increased need in the development of portable handheld devices, capable of on-the-spot chemical and biological sensing applications. Specific interests lie in electrochemical biosensors and screen-printed electrodes (SPEs) due to the decreased costs, an ability to integrate with handheld devices, and their user-friendly nature. Together, these qualities make the devices more accessible in resource-poor settings. Two of the most common substrates used to fabricate SPEs are carbon and gold. Carbon SPEs are effective in sensing applications yet challenged when attempting to covalently attach biomolecules to the surface. Gold SPEs have higher affinity towards biomolecules and improve the sensitivity, selectivity, and stability of a device; yet they can be costly. A carbon SPE modified with gold may be an ideal candidate to create an efficient low-cost device, using electrochemical gold deposition. In this study, electrochemical gold deposition on SPEs is explored to enhance the surface area and conductivity towards sensing applications. These SPEs were then modified with a thiol-based self-assembled monolayer (SAM) which demonstrates this technique could be used for further modification towards biosensing.

Highlights
Electrochemically deposited gold on screen-printed carbon electrodes.
Enhanced conductivity and surface area of electrodes for sensing applications.
Developed a new method to create inexpensive gold electrode.
Enabled gold-thiol chemistry commonly used for biosensing applications.
Electrochemical Engineering
093501
The following article is Open access
Andrei Kulikovsky
A model for performance and impedance of a partially flooded cathode catalyst layer (CCL) in a low-platinum PEM fuel cell is developed. The CCL is modeled by a system of cylindrical pores approximating real pore–size distribution in the electrode. The model includes oxygen transport along the pores and through the ionomer film covering Pt/C agglomerates. Part of the pore domain adjacent to the membrane is allowed to be flooded. Fitting of the model to experimental impedance spectra of a low-platinum PEM fuel cell shows 30%–40% CCL flooding. Flooding effectively reduces the CCL volume available for current conversion, thereby lowering the limiting current density due to oxygen transport through the ionomer film.
093502
Anahita Asadi, Hesam Bazargan Harandi, Bolin Kang, Joey Chung-Yen Jung and Pang-Chieh Sui
As a part of the recycling process of spent lithium-ion batteries, electrodialysis (ED) is used to extract lithium hydroxide and sulfuric acid from the lithium sulphate solution. This study reports on a multicomponent, 2-dimensional ED model based on simultaneously solving the Nernst-Planck equation, Navier–Stokes equations, species conservation with electrochemical reactions, and electro-osmotic water flow equations using computational fluid dynamics technique. To satisfy the electroneutrality assumption in the ED device, the fluxes of H+ and OH− ions produced from electrochemical reactions are estimated. The distributions of velocity, potential, and species’ concentrations are determined. A close agreement between the present model and experimental data shows the accuracy and validity of this work. The influence of transmembrane water flow is investigated. It is revealed that although the water molecules transferring from dilute to concentrate compartments reduce the concentration of concentrate channels, the generated ionic convection flux reversely affects this quantity. A parametric study is carried out to study the effects of operation conditions and membrane properties. It is found that 37% growth of dilute channel concentration is observed when inlet velocity increases from 50 to 100 μm·s−1. The enhancement of the water volume fraction of membranes also reduces the transmembrane water flow rate.
093503
Ha Huu Do, Kwun Nam Hui, Pham Gia Vu, Kwan San Hui and Duc Anh Dinh
The development of durable, efficient catalysts is vital in electrochemical water dissociation. Metal-organic frameworks (MOFs) based nanomaterials have been explored due to their well-distribution metal nodes and stability, but the shortage of efficient cathode compounds for electrochemical hydrogen evolving restricted their industrial applications. Herein, Cu2Se nanocrystals embedded in the octahedral carbon frameworks (Cu2Se/C) were fabricated using a copper-related MOF template through a one-step selenization technique. Interestingly, the catalytic efficacy of Cu2Se/C is better than that of Cu/C and Cu-MOF as catalysts for hydrogen generation in an acidic medium. In particular, Cu2Se/C shows a moderate overpotential of 220 mV at a current density of 10 mA cm−2 and a low Tafel slope of 54.5 mV dec−1. Also, this catalyst presents outstanding durability with 2000 cycling operations and 12 h of testing by chronoamperometry. The high efficiency is assigned to the synergistic effect of Cu2Se nanoparticles and carbon frameworks, which play essential roles in increasing exposed catalytic sites and protected active centers. The results may open potential direction to prepare economical hydrogen-evolving electrocatalysts.
093504
Shiyi Wang, Xinlei Wang, Guiqing Yuan, Yu Zhang, Xiangxiang Zhu, Xufei Zhu and Ye Song
Sparking voltage is one of the vital parameters of the working electrolytes for aluminum electrolytic capacitors, which determines the operating voltage of the capacitors. However, the existing methods for measuring the sparking voltage suffer from low accuracy, bad reproducibility, high artificial error, etc. In this paper, we reported a versatile approach to determining the sparking voltage of the electrolytes. By a linear fitting procedure, the voltage-time data acquired from the test experiments were transformed into a correlation coefficient-time curve. Since the abrupt correlation coefficient change due to the occurrence of sparking could be more readily identified in the correlation coefficient-time curve, the limit voltage of the electrolyte was accurately determined. Thus, this voltage was subtracted from the IR drop in the solution to get the true sparking voltage of the electrolyte. This method prevented artificial errors arising from the direct observation or listening of sparking features, by which reliable and reproducible results can be gained by a computer program. This study provided active support for the development of high-performance working electrolytes.
093505
Yu Yu, Yiwei Zhong, Ying Li, Wei Ren, Mingyong Wang and Zhancheng Guo
Invar alloy film with low thermal expansion is a key substrate for high-resolution organic light-emitting diodes (OLEDs). The preparation of Invar alloy film by electrodeposition has attracted increasing attention due to its low cost and simple process. In this work, a large-sized (8 × 10 cm) uniform Fe-Ni alloy film was fabricated by pulse reverse electrodeposition. The effects of the electrodeposition parameters on the chemical composition and microstructure of Fe-Ni alloy films were investigated. Results showed that greater Ni2+/Fe2+ in the electrolyte, lower pulse frequency (f), smaller reverse pulse coefficient (x), and lower electrodeposition temperature (T) favored the iron content. The Invar alloy film (64 wt% Fe) was electrodeposited at T = 50 °C, x = 0.2, f = 10 Hz, and Ni2+/Fe2+ = 1.9 when the average pulse current density was 30 mA cm−2. The structure of the film was composed of a mixture of fcc and bcc phases, where (110) and (111) preferential orientations were predominant. After heat treatment in H2 at 800 °C for 120 min, the bcc phase transformed into the fcc phase, and the grain size increased (>2 μm). As a result, the coefficient of thermal expansion of the film decreased from 11 × 10−6 to 1.5 × 10−6/°C, which is close to the standard for commercial application.

Highlights
Large-sized Invar alloy film was fabricated by pulse reverse electrodeposition
High iron content was obtained at lower pulse frequency and reverse pulse coefficient
CTE of the Invar alloy film was 1.5 × 10−6/°C after heat treatment at 800 °C in H2
093506
Ji-Hyung Han
This is the first report discussing the long-term stability (1000 h) of direct seawater electrolysis (DSWE) in relation to seawater acidification and inorganic precipitation. Unlike general DSWE, in which inorganic precipitates are formed at the cathode surface due to a local pH increase caused by the hydrogen evolution reaction (HER), bipolar membrane-based DSWE acidified natural seawater to pH 3, suppressing the formation of inorganic precipitates and inducing a positive shift in the equilibrium potential for the HER. Because the acidified seawater became alkaline after 300 h, periodic seawater replacement was suggested as a method of maintaining seawater acidification for 1000 h, during which a Mg(OH)2 film with a thickness of 1 mm or more was formed at the cathode surface. Using Brunauer–Emmett–Teller (BET) analysis, water vapor sorption, and electrochemical impedance analysis, it was confirmed that the Mg(OH)2 film has a hierarchical mesoporous structure and high affinity for water, which maintained mass transport. The unique properties of the Mg(OH)2 film under seawater acidification contributed to a lower rate of increase in the cathodic potential than that under seawater alkalization, where very thin inorganic deposits were formed.

Highlights
Seawater (catholyte) was acidified for 1000 h despite hydrogen evolution reaction.
Periodic replacement of seawater maintained the concentration of Mg2+.
High porosity and water affinity of thick Mg(OH)2 film enhanced mass transfer.
Cathodic potential rose slowly in seawater acidification vs seawater alkalization.
093507
Guillaume Hopsort, Laure Latapie, Karine Groenen Serrano, Karine Loubière and Theodore Tzedakis
In the present work, all the by-products formed during the urea electrooxidation (UEO) by Ni(III) in alkaline medium are identified and quantified for the first time (e.g., 



). Complete mass balances are simultaneously established in both aqueous and gas phases for large urea conversion rates (>80%). The results provide clear evidence (with a maximal deviation of 2%) that, in addition to
N-overoxidized by-products are produced during the UEO. Electrolyses conducted with human urine samples under identical operating conditions result in different distributions of N and C-by-products. In particular, the formation of formic and oxalic acids in these latter experiments suggests the presence of different and/or additional mechanistic pathways during the UEO process. The amount of
generated at the cathode is also quantified, showing a reduction of 30% in energy consumption when compared with water electrolysis. Finally, this study assesses the energy efficiency of UEO with urea synthetic and real-matrix effluents, thereby contributing to the development of this sustainable process, which enables energy recovery from waste.

Highlights
Elucidation of all the by-products occurring during UEO;
Complete mass balances in both liquid and gas phases for large urea conversion;
Nitrogen is not the main nitrogenous by-product;
Comparison of electrolysis efficiency between synthetic and real matrix urine;
Energy consumption of the electrolyzers for producing H2 from urine.
093508
Jiajun Lu, Sanjun Liu and Yonghua Zhao
Analogous to difficult-to-cut materials in mechanical machining, Niobium (Nb) is a difficult-to-dissolve metal by electrochemical machining (ECM) due to its prone-to-passivation nature. Jet-electrochemical discharge machining (Jet-ECDM), which uses anodic discharge rather than the cathodic discharge as in traditional ECDM, has been previously demonstrated as an efficient method for machining inert semiconductors like Si, 4H-SiC. However, applying Jet-ECDM on Nb-like passivating metal is very challenging because plasma electrolytic oxidation (PEO) is very prone to occur in the machining area due to anodic discharges, forming an insoluble, highly stable oxide coating that prevents material removal. This study reveals the principles of overcoming PEO to enable Jet-ECDM on metals. The findings show that the discharge intensity, affected by the electric field and pulse frequency, is decisive in achieving Nb material removal. The electrolyte chemistry significantly influences material removal fashions, depending on the electrolyte’s chemical activity. NaOH is the preferred choice for higher removal efficiency (maximum 1.92 mm min−1) and machining localization, while NaCl ensures better surface quality (Sa 99.4 nm). Moreover, the Jet-ECDM generated microstructure surface presents a thin layer of PEO coatings (<1 μm). This demonstrates the high potential of Jet-ECDM technology for efficient fabrication of coated microstructures in a single-step process.
Highlights
Applied electricity and pulse shape exert critical influence on realizing material removal.
The right electrolyte chemistry can significantly promote the material removal rate.
The discharge behavior is influenced by the electrolyte type and temperature.
Chemical factors play a more important role in overcoming PEO than discharge energy.
PEO coating-microstructure integrated fabrication is realized by Jet-ECDM.
093509
The following article is Open access
Charles W. Monroe
Motivated by years of correspondence with Prof. Ralph White, I discuss two unconventional ways to solve diffusion problems with Laplace transforms. A method to derive error-function series, alternatives to Fourier series that converge rapidly and avoid the Gibbs phenomenon at short times, is illustrated by example. It is shown how Mittag-Leffler partial-fractions expansions can facilitate derivations of Fourier-series solutions from the same starting point. Several basic problems pertinent to electrochemical transport are analyzed, culminating in the development of a modified Cottrell equation applicable to thin films of unsupported electrolytic solutions sandwiched between planar electrodes.
093510
The following article is Open access
Qiaohao Liang and Martin Z. Bazant
As the design of single-component battery electrodes has matured, the battery industry has turned to hybrid electrodes with blends of two or more active materials to enhance battery performance. Leveraging the best properties of each material while mitigating their drawbacks, multi-component hybrid electrodes open a vast new design space that could be most efficiently explored through simulations. In this article, we introduce a mathematical modeling framework and open-source battery simulation software package for Hybrid Multiphase Porous Electrode Theory (Hybrid-MPET), capable of accounting for the parallel reactions, phase transformations and multiscale heterogeneities in hybrid porous electrodes. Hybrid-MPET models can simulate both solid solution and multiphase active materials in hybrid electrodes at intra-particle and inter-particle scales. Its modular design also allows the combination of different active materials at any capacity fraction. To illustrate the novel features of Hybrid-MPET, we present experimentally validated models of silicon-graphite (Si-Gr) anodes used in electric vehicle batteries and carbon monofluoride (CFx) - silver vanadium oxide (SVO) cathodes used in implantable medical device batteries. The results demonstrate the potential of Hybrid-MPET models to accelerate the development of hybrid electrode batteries by providing fast predictions of their performance over a wide range of design parameters and operating protocols.
093511
Akshay Subramaniam, Suryanarayana Kolluri, Taejin Jang, Rayan Charab, Daniel Jimenez, Francisco Trinidad, Diptarka Majumdar and Venkat R. Subramanian
A one-dimensional (1D) electrochemical model is developed for a lead-acid demonstration cell comprising two positive electrodes engaging a single negative electrode. Classical 1D models, which analyze a single repeat unit in a full battery, are extended to this non-standard configuration by considering additional porous electrode and electrolyte reservoir domains. The non-standard model necessitates appropriate boundary conditions to couple electrochemical variables in different domains, since symmetry boundary conditions typically employed at the current collector grids are no longer applicable. The modified model, with new boundary conditions, is simulated using standard techniques. Salient modeling and simulation differences compared to a standard lead-acid model are discussed, as are trends in predicted variables. The non-standard model predicts reduced polarization and more uniform utilization of the non-limiting electrodes, in addition to non-zero reaction currents and active material utilization in the terminal electrode faces, which are typically ignored in “unit-cell” analyses. This model is expected to be of substantial utility in guiding evaluations of new lead-acid battery designs through improved prediction of performance of such test configurations. The boundary conditions introduced herein are also useful for 1D modeling of non-standard configurations characterized by multiple, electrochemically interacting porous domains, particularly where spatial current distributions are initially unknown.
093512
Ayoub Najem, Othon S. Campos, Gábor Girst, Mounir Raji, Attila Hunyadi, José García-Antón, Abdelkbir Bellaouchou, Hatem M. A. Amin and Maria Boudalia
Developing green anticorrosive films is gaining great attention in science and engineering. Citrus fruit peels are mainly discarded as waste, although they can be an excellent repository of phytochemicals, that can be exploited as mitigating agents for corrosion. Herein, we report the high anticorrosion activity of a citrus extract for low-carbon steel in 1 M HCl solution at different temperatures. The main extract constituents were identified by MS and NMR. Two polymethoxyflavones (PMFs), namely nobiletin and heptamethoxyflavone, were identified as major constituents of the extract and the crude PMFs-based extract was investigated for corrosion protection. Using potentiodynamic polarization, weight loss and electrochemical impedance spectroscopy (EIS) methods, this extract revealed improved inhibition efficiency of 94%. The inhibition mechanism was elucidated by considering electrochemical kinetics and adsorption thermodynamics. SEM and UV–vis supported the electrochemical results. PMFs-based extract acted as a mixed-type inhibitor with a Langmuir model of adsorption. Importantly, DFT simulations provided atomic-level insights into the inhibition mechanism and unraveled donor-acceptor interactions between the methoxy groups of PMFs and iron atoms, facilitating the formation of a stable inhibition adsorption layer, and thus supporting the experimental findings. In addition to the physical barrier effect of PMF inhibitor, π-back bonding effect between PMF and steel was suggested.

Highlights
Five polymethoxyflavones (PMFs) with nobiletin and heptamethoxyflavone as majors were successfully isolated from a citrus peel waste.
The crude extract was exploited as a green ecofriendly corrosion inhibitor.
A remarkable corrosion protection efficiency of 94% was achieved.
PMFs adsorb on iron steel following a Langmuir isotherm, forming a protective blocking layer.
DFT calculations provided insights into the interfacial adsorption mechanism at the molecular/atomic level.
Fuel Cells, Electrolyzers, and Energy Conversion
094501
F. Kukk, S. Pylypko, E. Lust and G. Nurk
Reversible solid oxide cell technology (RSOC) is a key technology in future hydrogen energy concept and may play a significant role in stabilizing intermittent renewable electric power sources. This work handles an attempt to optimize the thickness of the hydrogen electrode active layer (HEAL) for solid oxide cells designed and developed initially for fuel cell application (SOFC). Five cells with HEAL thickness of 0, 7, 12, 16 and 20 μm, prepared using industrial manufacturing methods, are analyzed using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) methods under a wide range of operating conditions. Optimal thickness of an active layer studied depends on operating conditions. Depending on the temperature and feed gas water content applied highest performances were achieved for cells with HEAL thicknesses between 7 and 16 μm. At 800 °C and 90% feed gas water content, the best cell had an active layer of 7 μm, drawing −3.5 A cm−2 current at −1.4 V.
094502
The following article is Open access
Xiaoqiang Zhang, Danan Yang, Min Xu, Aaron Naden, Mayken Espinoza-Andaluz, Tingshuai Li, John T. S. Irvine and Martin Andersson
Solid oxide fuel cells (SOFCs) directly convert chemical energy to electricity with high electrical efficiency. It involves gas transport through the porous electrode to the three-phase boundaries (TPB). The tortuosity of gas transport relates the bulk diffusion of gas in free space to the effective diffusion coefficient of gas migrating through a porous material. Therefore, determining the tortuosity is of great importance. This paper tests button SOFCs with NiO-YSZ as anode material followed by dual beam-focused ion beam scanning electron microscopy (FIB-SEM) to obtain 2D serial slice images. Based on processed 2D images and reconstructed 3D microstructure, the tortuosity is calculated using three approaches i.e., porosity-tortuosity correlations, voxel-based, and path-length-based approaches. The test results show that a decrease in Ni content in the anode greatly decreases the cell performance due to a decreased percolated electronic phase. The sample with low performance has high tortuosity. Different approaches vary regarding the tortuosity value and computational time. The path-length-based approach can achieve reasonable accuracy in a relatively short time but is only valid for using the longest path length.
094503
The following article is Open access
Yan-Sheng Li, Davide Menga, Hubert A. Gasteiger and Bharatkumar Suthar
094504
Muhammad Nihal Naseer, Asad A. Zaidi, Kingshuk Dutta, Juhana Jaafar, Yasmin Abdul Wahab and Yuhang Cai
Microbial fuel cell (MFC) is attractive for research community as a promising bioelectricity production technology using organic waste. However, due to low performance and erroneous reproducibility and replicability, MFC lacks industrial application. Additionally, the nonlinear dynamic behavior of MFC, along with the involvement of electrochemistry and biology in mathematical models, makes it difficult to comprehend and simulate. To overcome these barriers, this study provides a simulation platform for conducting theoretical studies using a fundamental mathematical model of MFC. This novel Simulink/MATLAB model is based on mass balance across both compartments of MFC, and provides power density as a function of a wide range of performance-affecting parameters. Model validation depicts only 2%–10% error. This model can provide a stepping stone to perform theoretical optimization and industrial application studies in future. By varying the values of different parameters; studies may be performed to spot optimum values of the most sensitive parameters. Therefore, using the proposed tool paves the path for further improvements in design, cost effectiveness and performance efficiency that ultimately promises up-scaling of MFCs as a renewable and alternative energy resource.
Highlights
Proposed model simulates various design inputs to predict the performance of MFCs
Verification with experimental data demonstrates an error between 2%–10% only
Simulation tool provides a platform for sensitivity analysis of design parameters
Simulation tool help in optimization studies prior to experimentation
Model reduces computational time to only 10 s, also provides a user-friendly interface
094505
The following article is Open access
Nagappan Ramaswamy, Samantha Kapushy, Nathan P. Mellott, Ashley LaLonde, Roland Koestner, Frank D. Coms and Swami Kumaraguru
Precious group metal-based catalysts based on Pt- and Pt-alloys are currently used as catalysts for the kinetically sluggish Oxygen Reduction Reaction (ORR) on the cathode of fuel cells. The activity of Pt or Pt-alloy catalysts towards ORR is severely compromised by the adsorption of spectator-species such as sulfonate anions from perfluorosulfonic acid (PFSA) ionomer or Pt-O(H)ad via water activation. Considering recent evidence pointing to the improvement in ORR activity via the use of melamine organic molecule or melamine-formaldehyde copolymeric additives as surface blocking agents for the prevention of sulfonate or Pt-OHad adsorption, we evaluated these additives in fuel cells. The catalysts were modified with either of these additives and characterized using ex situ and in situ methods to verify successful adsorption and eventual performance in fuel cells. These surface modifying agents were found to suppress Pt-OHad formation as well as suppress ORR activity. There was no evidence to point out that these additives improved ORR activity and H2/air polarization performance in a fuel cell MEA on supported, polycrystalline Pt catalyst.
094506
Anusorn Kongkanand, Venkata Yarlagadda, Wenbin Gu and Srikanth Arisetty
Pt surface oxide coverage (POC) and Oxygen Reduction Reaction (ORR) were measured under a range of operating conditions in a Proton Exchange Membrane Fuel Cell (PEMFC). Sensitivity analysis suggests that adsorption of sulfonate groups of the ionomer on the Pt surface plays an important role in POC and ORR kinetics. Although both Pt oxide growth and ORR activity decay follow a logarithm of time behavior, it is found that ORR kinetics are affected by at least two different types of Pt oxide. A semi-empirical ORR kinetic model is proposed taking into account the effect of ionomer and Pt oxide types. The model is capable of providing a quantitative prediction of POC and ORR activity over a range of potential, temperature, relative humidity, and time that is relevant to normal PEMFC operation.
094507
The following article is Open access
Lena V. Bühre, Alexander J. McLeod, Patrick Trinke, Boris Bensmann, Mareike Benecke, Omar E. Herrera, Walter Mérida and Richard Hanke-Rauschenbach
This work presents a platinum wire micro-reference electrode suitable for recording in-operando individual electrochemical impedance spectra of both the anode and the cathode in a proton exchange membrane water electrolyzer. The setup enables the protonic membrane potential to be accessed outside the active area. The reference electrode allows for the analysis of kinetic parameters for anode and cathode reactions separately. However, the exact location of the measured membrane potential is unknown due to a potentially asymmetric potential distribution, which makes the calculation of exact kinetic parameters non-trivial. Qualitative analyses of the potential distribution behavior over temperature, cell compression, and current density are shown.
094508
The following article is Open access
Tianyi Han, Liangfei Xu, Yang Zhao, Shukai Zhang, Zunyan Hu, Jianqiu Li and Minggao Ouyang
Increasing the power density of proton exchange membrane fuel cell (PEMFC) is essential for its commercialization. Cathode catalyst layer (CCL) carbon additive is an effective method that can improve membrane electrode assembly (MEA) performance under high current density. In this work, carbon nanofiber (CNF) is used as CCL additive and its mechanism is studied. The influence of CNF on the CCL structure is studied by scanning electron microscope (SEM), nitrogen adsorption method and contact angle experiment. Meanwhile, the mechanism is examined by using polarization decomposition and impedance analysis combined with the result in characterization experiments. The results show that: (1) the MEA used in this work has the best performance when adding 1 wt%. The voltage rises 74 mV (15.42%) at 2 A cm−2; (2) CNF varies the MEA performance mainly through changing the hydrophobicity of CCL, influencing the mass transport resistance and the concentration polarization. The mass transport resistance decreases 57.18% at 2 A cm−2; (3) activation polarization values have a negative linear correlation with the peak volume values of the primary pores at around 4 nm in diameter. This study provided a detailed understanding of the mechanism of CNF additive in CCL and will be helpful for improving PEMFC performance.

094509
The following article is Open access
Anne Berger, Yen-Chun Chen, Jacqueline Gatzemeier, Thomas J. Schmidt, Felix N. Büchi and Hubert A. Gasteiger
Interfaces are crucial for the water management in polymer electrolyte membrane fuel cells (PEMFCs). The introduction of a microporous layer (MPL) had a revolutionary effect on the water distribution by improving the interface between the catalyst layer and the gas diffusion layer substrate (GDL-S). Hence, it is vital to maximize the improvement by further characterizing and advancing the properties of the interfaces, in this case the MPL/GDL-S interface. This study aims at fabricating a GDL with an MPL that intrudes into the GDL-S, analyzing the impact on the GDL-S structure and on PEMFC performance. Mercury intrusion porosimetry (MIP) and ex situ X-ray tomography (XTM) show that the intrusion of the MPL into the hydrophobic GDL-S proceeds via the preferential filling of the GDL-S macropores, thereby reducing their size and volume fraction in the GDL-S. While an intruding MPL leads to a small performance increase under wet PEMFC operating conditions, this improvement could only be achieved by a careful management between the extent of MPL intrusion and the partial macropore blocking in the GDL-S. Furthermore, the impact of MPL intrusion on the liquid water saturation of the GDL was quantified by operando XTM. The results provide design guidelines for improved GDLs.
Organic and Bioelectrochemistry
095501
Faezeh Zivari-Moshfegh and Davood Nematollahi
In order to discover more information about the toxic metabolites formed from the oxidation of rifampicin and acetaminophen in the body, the electrochemical oxidation of these drugs together and also in the presence of vitamin C was studied. This work has led to strong evidence of a catalytic reaction between vitamin C and the oxidized form of rifampicin. Also, contrary to the published reports, the results of this study have discovered another catalytic reaction between oxidized acetaminophen and rifampicin. The results of this study can be used to prevent the toxic effects of rifampicin and acetaminophen and/or prevent the poor bioavailability of these drugs.

Physical and Analytical Electrochemistry, Electrocatalysis, and Photoelectrochemistry
096501
Kangli Chen, Yuan Li, Guanjiu Wu, Qing Wang, Chenfeng Fan, Lu Zhang, Jianzheng Song and Shumin Han
Designing Earth-abundant, cost-effective catalysts for hydrogen evolution via water splitting is essential for hydrogen generation. Adding a third metal element to binary phosphides provides the opportunity to tune their morphology, crystalline and electronic structures and thus their electrocatalytic properties. In this study, a hierarchical crystalline/amorphous Ni−Co−P compound is prepared on nickel foam (NF) with different nickel to cobalt ratio by one-step electrodepositing technique. The Ni−Co−P/NF is composed of metallic Co and amorphous phosphides. It has hierarchical morphology, consisting of ∼800 nm spherical particles in the bottom layer, ∼1.5 μm spherical particles in the middle layer, and staggered network structure on the top layer. The Ni−Co−P/NF electrode exhibits superior hydrogen evolution reaction (HER) catalytic activity in the alkaline solution, which requires only 72 mV for delivering 10 mA cm−2. More importantly, the Ni−Co−P/NF catalyst sustains the current density of 20 mAcm−2 for 53 h with negligible degradation in overpotential which shows remarkable electrochemical stability.

Highlights
The hierarchical crystalline/amorphous Ni–Co–P compound is prepared on nickel foam (NF) by one-step electrodepositing technique.
The Ni–Co–P/NF electrode exhibits a low overpotential of 72 mV at a current density of 10 mA cm−2 and a small Tafel slope of 92 mV dec−1.
The Ni–Co–P/NF shows high stability at a current density of 20 mA cm−2 for 53 h.
096502
S. Irem Kaya, Mahsa Majidian, Goksu Ozcelikay-Akyildiz, Ahmet Cetinkaya, Burcu Dogan Topal, Esen Bellur Atici and Sibel A. Ozkan
This study reported the molecular imprinting process investigated by two techniques: photopolymerization (PP) and thermal polymerization (TP). These techniques were integrated with an electrochemical sensor to determine the new generation anticancer drug Olaparib (OLP), which is a poly(ADP-ribose) polymerase (PARP) inhibitor with high sensitivity and selectivity. The PP-MIP film was formed by PP, while TP-MIP film was formed by TP on a glassy carbon electrode (GCE). In the PP-MIP(OLP)/GCE sensor, which was developed using PP, 4-aminobenzoic acid (4-AB) as a functional monomer was designed, and obtained in the presence of basic monomer (HEMA, 2-hydroxyethyl methacrylate), crosslinker (EGDMA, ethylene glycol dimethacrylate), and initiator (2-hydroxy-2-methyl propiophenone) by keeping it under a UV lamp at 365 nm. For TP-MIP(OLP)/GCE was obtained by using a mixture of 4-AB as a functional monomer, NH3 solution, surfactant sodium dodecyl sulfate (SDS), and tetraethyl orthosilicate (TEOS): ethanol (1:1, v/v) and keeping it in an oven at 50 °C for 40 min. After each process, the GCE surfaces were characterized via scanning electron microscope and electrochemical techniques (cyclic voltammetry and electrochemical impedance spectroscopy). The required optimization studies were performed for both techniques. After obtaining the optimum MIP-integrated electrochemical sensors, the analytical performances of PP-MIP(OLP)/GCE and TP-MIP(OLP)/GCE were evaluated, and the validation parameters were compared. The linear ranges of PP-MIP(OLP)/GCE and TP-MIP(OLP)/GCE are 0.1–1 nM. The PP-MIP(OLP)/GCE and TP-MIP(OLP)/GCE were applied to commercial serum samples and pharmaceutical dosage forms. The selectivity of proposed sensors was also proven using similar structures of OLP through imprinting factor. The results show that the proposed PP-MIP(OLP)/GCE and TP-MIP(OLP)/GCE sensors have good selectivity, high sensitivity, accuracy, and precision. The determination of OLP was achieved with these electrochemical sensors for the first time.

Highlights
The first MIP-based electrochemical sensor application for OLP analysis
Comparison of molecular imprinting methods (photo and thermal polymerization)
Successful application of the MIP-sensors to serum and tablet samples
096503
S. Brindha Devi and R. Navamathavan
The demand for green and clean technology motivates the research community to find a novel electrocatalyst for overall water-splitting. Therefore, in this study, we developed a hybrid non-noble metal catalyst nanocomposite of Ti3C2–CoS2 (TC-CS) as a bifunctional electrocatalyst for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). The nanocomposite shows crushed nanosheets of Ti3C2 sprinkle on the CoS2 (CS) surface thus increasing the electrochemically active surface area of the catalyst. The nanocomposite exhibits a low overpotential of 276 mV for HER and 376 mV for OER with a Tafel slope of 159 mV dec−1 and 22 mV dec−1. This new kind of MXene composite will create a revolution in future energy technology.
096504
Michely P. Rosseto, R. R. Ribeiro de Almeida, R. S. Zola, E. K. Lenzi and L. R. Evangelista
We analyze the electrical impedance response established in terms of the time-fractional approach formulation of the Poisson-Nernst-Planck model by considering a general boundary condition. The total current across the sample is solenoidal, as the Maxwell equations require, and the boundary conditions can be related to different scenarios. We also study the behavior of the electrical conductivity and its connection with the ionic spreading in the sample to establish the diffusion regime present in the system in the low-frequency limit. Furthermore, we investigate impedance spectroscopy measurements of a nematic liquid crystal cell and observe a good agreement between the experimental data and the model.
096505
The following article is Open access
Burkhard Hecker, Elisabeth Robens, Helen E. Valencia, Anna Windmüller, Falk Muench, Maria Meledina, Hermann Tempel, Hans Kungl, Joachim Mayer and Rüdiger-A. Eichel
Using a tunable electroless nanoplating reaction, different silver structures including two nanoplate-based structures were synthesized, characterized and tested as catalysts to improve the electrochemical reduction of CO2 towards CO. Relative to a planar polycrystalline silver surface, the faradaic efficiency to CO was significantly improved, from 7% to 67% at −0.6 V vs RHE and from 51% to 97% at −1.0 V vs RHE, decreasing the parasitic evolution of hydrogen and formate. By comparing the catalytic performance of three intensively characterized silver structure types, namely high aspect ratio nanoplates, particulate nanoplate clusters, and interconnected grain-like particles, in-depth insights into various effects that influence the observed reactions are presented. In particular, at low potentials and high current densities, the catalytic performance is more related to the electrochemical surface area and local transport effects. The obtained results demonstrate the relevance of structural control in electrocatalysts and the special effects of nanoplate structures. Thus, our findings provide a useful groundwork for the practical design of electrocatalysts for CO2 reduction.
Highlights
Effect of nanoplate structure on the electrochemical CO2 reduction
Electroless synthesis of silver nanoplates as thin films on metal foil
Electrocatalyst design improving the selectivity to carbon monoxide
Structure related mass transport effects on the electrochemical reaction
096506
The following article is Open access
Martin D. M. Badley, David W. Shoesmith and James J. Noёl
The ability of hydrogen (H2) to scavenge hydroxy radicals (OH•) created by the dissociation of hydrogen peroxide (H2O2) on the surface of uranium dioxide (UIVO2) has been studied in a chloride/bicarbonate (pH = 9.5) solution. The oxidation/reduction of the oxide surface was monitored by measuring the corrosion potential as a function of time in this solution, containing various concentrations of H2O2 sparged with either Ar or an Ar/H2 mixture. The surface oxidation was subsequently determined using X-ray photoelectron spectroscopy. In the absence of H2, the peroxide oxidized the surface to UIV1–2xUV2xO2+x with x varying with H2O2 concentration and eventually achieved a composition of UIV0.34UV0.66O2.33. At this surface composition, the surface becomes unstable with respect to dissolution, but the dominant reaction is H2O2 decomposition. In the presence of H2, the initial oxidation of the UIVO2 when H2O2 was added was reversed by the ability of H2 to scavenge the OH• with the H• radicals formed. This led to a reduction of the oxidized surface. The efficiency of this process is determined by the relative concentrations of H2O2 and H2.
096507
Catherine J. McMahon, Brandaise Martinez and Charles S. Henry
Thermoplastic carbon electrodes (TPEs) are an alternative form of carbon composite electrodes that have shown excellent electrochemical performance with applications in biological sensing. However, little has been done to apply TPEs to environmental sensing, specifically heavy metal analysis. The work here focuses on lead analysis and based on their electrochemical properties, TPEs are expected to outperform other carbon composite materials; however, despite testing multiple formulations, TPEs showed inferior performance. Detailed electrode characterization was conducted to examine the cause for poor lead sensing behavior. X-ray photoelectron spectroscopy (XPS) was used to analyze the surface functional groups, indicating that acidic and alkaline functional groups impact lead electrodeposition. Further, scanning electron microscopy (SEM) and electrochemical characterization demonstrated that both the binder and graphite can influence the surface morphology, electroactive area, and electron kinetics.
096508
Xingxing Liao, Zhaode Mu, Panke He, Yonghua Yuan, Jiaxu Zhou and Lijuan Bai
In this work, a new non-enzymatic sensor for the determination of glucose was constructed using Fe-doped NiMoO4 nanoparticles (NiFeMoO4). Hydrothermal and calcination techniques were successfully used to synthesis different proportion nanoparticles of Ni1−xFexMoO4 (x = 0, 0.01, 0.03, 0.05). A set of electrochemical measurements demonstrated that all of the Ni1−xFexMoO4 have electrocatalytic properties to glucose. Especially, Ni0.99Fe0.01MoO4 (x = 0.01) displayed the most excellent amperometric response to glucose in the range of 0.01∼13 mM with a limit of detection (LOD) of 0.29 μM (S/N = 3). This amperometric sensor also showed satisfactory anti-interference performance and stability. More significantly, the sensor’s applicability was tested using a glucose assay in actual serum samples with acceptable results.
Sensors
097501
Cheng Li, Xiao Zhang, Jia Liu, Guoqing Liu, Guangying Sun, Wanli Xu, Qifu Zheng, Jian Xie and Hangjia Shen
Iron-N–C (Fe–N–C) materials are facilely synthesized by chemical vapor deposition (CVD) and applied in detecting hydrogen peroxide. Benefiting from the merits of Fe–N–C configuration, the achieved Fe–N–C modified electrodes exhibit outstanding electrochemical sensing performances toward pH-universal hydrogen peroxide detection.
097502
Subburaj Srinithi, Catherin Meena Boominathan, Shen-Ming Chen, Elayappan Tamilalagan and Vellaichamy Balakumar
N-acetyl-p-aminophenol, commonly known as paracetamol (PAL), is a widely prescribed drug for the treatment of fever and moderate pain. The presence of PAL at trace levels has been detected in hospital wastewater, drinking water, and sewage water, primarily due to its excretion from human and animal urine. Therefore, this work intends to improve the detection of PAL in human urine, thereby boosting its monitoring and analysis in environmental samples. Here in we developed a rational construction of the nanoflake structured vanadium pentoxide (V2O5) particles with functionalized multiwalled carbon nanotube [V2O5@f-MWCNT (1–4)] and evaluated their electrocatalytic performance for the detection of PAL. The synthesized materials were characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and Field emission scanning electron microscopy (FE-SEM) with elemental mapping analysis. The electrocatalytic performance of different electrocatalysts on the GCE surface was studied through cyclic voltammetry (CV) and differential pulse voltammetry (DPV). It was observed that the optimized V2O5@f-MWCNT-3 nanocomposite exhibited higher electrocatalytic activity towards PAL, resulting in a wide linear range of detection. The respectable limit of detection (LOD) of the V2O5@f-MWCNT-3 modified GCE was found to be 0.00185 μM and utilized for analyzing PAL in real samples.
097503
Alexandru-Adrian Bratei, Raluca-Ioana Stefan-van Staden, Ruxandra-Maria Ilie-Mihai and Damaris-Cristina Gheorghe
Cathepsins B, D and protein p53 are three of the biomarkers with a large spectrum of implications in the field of physiopathology as many diseases proved to be associated with their variation in concentration. Therefore, there is a need for reliable tools able to perform molecular recognition/differentiation, and also reliable quantification of cathepsins B, cathepsin D, and protein p53. Two stochastic microsensors based on diamond/graphene nanopowders modified with 2,3,7,8,12,13,17,18-octaethyl-21H,23H-porphine manganese (III) chloride were proposed for the simultaneous differentiation and quantification of cathepsins B, D and protein p53 in whole blood, urine, saliva, and tumoral tissues. The lowest limits of determination and the highest sensitivities were recorded when the stochastic microsensor based on nanopowder of graphene was used. Wide linear concentration ranges were recorded for both microsensors. The recovery values obtained for the microsensors, were higher than 97.00%, and the relative standard deviations values were lower than 1.00%, when used for screening of whole blood, urine, saliva, and tumoral tissues.
097504
Yu-Ching Weng, Ting-Yu Yang, Chi-Jung Su and The-Wang Liu
A simple and novel electrochemical sensor based on a hydrophilic single-walled carbon nanohorn (SWCNH) modified glassy carbon electrode (GCE) was designed for the determination of acetaminophen (APAP). The hydrophilic SWCNH/GCE was characterized using Transmission electron microscopy (TEM), Raman spectroscopy, X-ray diffractometer (XRD), and X-ray photoelectron spectroscopy (XPS). This proposed sensor exhibits remarkable performance for the electrocatalytic detection of APAP. The hydrophilic SWCNH/GCE shows a good differential pulse voltammetry (DPV) response at APAP concentration from 100 to 1000 μM with sensitivity and a detection limit of 2.63 μAμM−1cm−2 and 1 μM. Regarding the reaction mechanism, the hydrophilic SWCNH/GCE could easily electro-catalyze APAP oxidation to form N-acetyl-p-benzoquinone-imine (NAPQI). Then NAPQI is rapidly degraded to p-benzoquinone in solutions of 0.1 M Na2SO4 and 0.05 M H2SO4 at pH 1.
097505
Noor Shahzad, Rabia Ajmal and Adeel Afzal
Gout arthritis, a painful condition characterized by the accumulation of uric acid (UA) crystals in the joints, necessitates the development of efficient and accessible diagnostic methods. In this study, we present the design and fabrication of non-enzymatic electrochemical sensors based on molecularly imprinted conducting polymer nanostructures for the selective detection and monitoring of UA. To overcome the limitations of current point-of-care (POC) diagnostics, we developed a disposable voltammetric sensor capable of selectively and accurately analyzing UA concentrations at room temperature and pH 7.4. The sensor utilizes a selective polythiophene layer, deposited on disposable screen-printed electrodes, for the reversible binding and recognition of UA. Extensive electrochemical measurements employing electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and differential pulse voltammetry (DPV) demonstrate excellent UA sensing performance in the wider concentration range of 1–500 μM using a standard redox solution with 2.91 μA cm−2·μM−1 sensitivity, 354 nM detection limit, and substantial selectivity over common interferents. The sensor is capable of analyzing complex mixtures such as human saliva with 90.4% recovery of the spiked UA concentration. This highly sensitive and cost-efficient electrochemical sensor offers great promise for POC testing, disease monitoring, and predicting treatment outcomes related to gout arthritis.
097506
Ni Xiao, Yinan Chen, Wen Tan, Jiangang Ku, Qiang Wang, Hang Chen, Wei Weng and Shuiping Zhong
Real-time and rapid determination of trace copper ion (Cu2+) in the electrolyte of zinc smelting process is urgently needed. However, the complicated composition of the electrolyte, especially the extremely high-concentration of zinc ion (Zn2+) may cause severe interference to the detection of Cu2+. This work describes a facile electrochemical sensor for Cu2+ determination in the electrolyte of zinc smelting plants based on a fluorine-doped tin oxide (FTO) electrode with silver nanowires (AgNWs) and Nafion modification. The AgNWs/Nafion-FTO electrode showed good detection ability with the linear detection range of 0.2−2 mg l−1 Cu2+ in 45 g l−1 Zn2+ solution using differential pulse anodic stripping voltammetry (DPASV) technique. With DPASV technique, Cu2+ can be first reduced and pre-concentrated on the working electrode surface at −0.6 V vs Ag/AgCl for 500 s, after which the deposited Cu metal is oxidized around 0 V vs Ag/AgCl during the stripping step. It has been proved by transmission electron microscopy (TEM) and X-ray photoelectron spectra (XPS) that trace Cu2+ can be adsorbed and reduced on AgNWs in solutions with Zn/Cu ratio up to (2.25−22.5) × 104. The results extend AgNWs modified electrode to the industrial solution, providing a new strategy for detection of trace metal ions in industrial solutions.
097507
Santa Islam, Abdul Awal, S. M. Abu Nayem, Shamsun Naher, Md. Delwar Hossain and A. J. Saleh Ahammad
Considering the adverse effect of sulfite (SO32−), an effective Ni(II)- and Ru(II)-based heterometallic-supramolecular polymer (HMSMP) (polyNiRu) has been synthesized. PolyNiRu was characterized by Field-emission scanning electron microscopy (FE-SEM), and Fourier transmission infrared (FT-IR) spectroscopy. The formation of HMSMP was confirmed via UV–Vis spectroscopy. The molecular weight of polyNiRu (4.77 × 105 Da) was measured through intrinsic viscosity measurement following Mark-Houwink equation. The electrochemical behavior of polyNiRu modified glassy carbon electrode (polyNiRu_GCE) was investigated via CV and DPV. Furthermore, we have investigated the Tafel plot for this heterogeneous electrochemical system to calculate the number of transferred electrons during redox reactions. The limit of detection was found as 0.25 μM with a wide linear dynamic range of 10 to 600 μM. A probable surface mechanism has been studied toward SO32− oxidation at the interface of polyNiRu_GCE. Using the Butler-Volmer equation, the heterogeneous kinetic rate transfer constant and charge transfer coefficient were found as 1.02 × 10−6 cm2 s−1 and 0.68 respectively. These obtained parameters were further evaluated by simulated CV, which agreed with the experimental value. Excellent recovery with lower relative standard deviation (RSD) and high stability for 4000 s in analytic solution confirmed the reliability of using this polyNiRu_GCE in the practical assessment.

097508
Noor Sultan, Ayub Alam, Batool Fatima, Sameera Shafi, Dilshad Hussain, Zohaib Sarwar, Muhammad Wasim, Saadat Majeed, Ahmad Yar and Muhammad Najam-ul-Haq
Liver cirrhosis is a life-threatening disorder characterized by severe hepatitis C. Early detection of hepatitis C is crucial since HCV infection has few symptoms, and the patient may remain unaware for many years. The early-stage detection can assist in the treatment and prevent further virus transmission. Abnormally varying albumin concentrations in hepatitis C patients can lead to hypoalbuminemia. Herein, a novel Co-Ni/TiO2 core–shell-based electrochemical sensor is developed for facile and ultra-sensitive human serum albumin (HSA) detection in HCV patients. Co-Ni/TiO2 core shells are fabricated via coprecipitation and hydrothermal methods and used for non-enzymatic detection albumin with high sensitivity, selectivity, and lower detection limits. Cyclic voltammetry, chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS) is performed for albumin detection via Co-Ni/TiO2 modified GCE at different scan rates, pH, and concentrations. The linear range and limit of detection (LOD) obtained for the Co-Ni/TiO2 electrode are 0–30 μM and 0.019 μM, respectively. The utility of Co-Ni/TiO2 electrodes is extended to HSA sensing from HCV-infected patients. Albumin recovery at room temperature ranged from 81.0% to 91.3% in diluted human serum samples. The developed electrochemical analysis method is superior for HSA detection and can be a tool for clinical diagnosis in the future.
097509
Hosna Ehzari and Elahe Darvishi
Nowadays, the use of nano-sensors has been considered in order to detect various compounds. In the food industry, nano-sensors are used to detect toxins, microbes and various compounds. Allura red is a red azo dye that is used in health and cosmetic, pharmaceutical and food industries. Azo dyes have toxic effects and can cause oxidative stress response and change the expression of different genes. Therefore, it is important to detect and determine its concentration. In this study, a simple and novel electrochemical sensor modified with ZnO nanoparticles (ZnO NPs) synthesized by the green method was fabricated and used for electrochemical detection of Allura Red in food samples. Surface morphology and electrochemical properties of the prepared nanocomposite modified electrode were investigated by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Under optimized conditions, the calibration plot was linear in the concentration renege of 0.01 μM to 0.41 μM, and the limit of detection was found to be 0.001 μM. The proposed sensor was successfully applied for determination of Allura Red in food samples.
097510
Youjian Zhang, Yuguo Wu, Ming Xue, Pei Chen and Dandan Li
Salicylic acid (SA) is effective in the treatment of coronary heart disease. In this study, a novel PEC sensor was prepared to specifically detect SA, and copper sulfide-layered double hydroxide/reduced graphene oxide (CuS-LDH/rGO) with visible light activity was chosen as the identification element and photoactive material. The photocurrent response of CuS-LDH/rGO shows linear relationship with SA concentration over a range of 1–80 μM and 160–5760 μM, with a low limit of detection (LOD) (S/N = 3) of 0.35 μM. Therefore, the novel PEC-sensing strategy proposed in this study represents an ultra-sensitive method with high selectivity and stability for the detection of SA.
097511
Pandia Rajathi Muthu Krishnan, Arunkumar Sakthivel and Subbiah Alwarappan
Sulfur doped graphitic carbon nitride (S-g-C3N4) was prepared by a thermal polymerization method using thiourea as a precursor. The as-prepared S-g-C3N4 was characterized by various surface probing techniques and employed as a platform for the electrochemical detection of DNA bases guanine (G), adenine (A), thymine (T), and cytosine (C). Effect of various buffers and pH essential for the selective and sensitive detection of all the DNA bases were also investigated. From the results, it was evident that PBS (pH 9.0) buffer is the best suitable medium for the DNA detection. A limit of detection of 13.22, 13.1, 37.7, and 14.61 μM (S/N = 3) and sensitivity of 1.76, 2.41, 0.68 and 2.38 μA cm−2μM−1corresponding to G, A, T and C respectively were noticed. Further, the proposed sensor was found to be linear in the range of 5–35 μM (G), 5–35 μM (A), 25–175 μM (T) and 25–175 μM (C). The proposed S-g-C3N4 modified electrode also exhibited a stable, selective and sensitive performance towards the detection of individual DNA base in the presence of other DNA bases.

Errata
099001
The following article is Free article
A. Sanjuan, W. H. Woodford, Y.-M. Chiang, W. Craig Carter and R. E. García
099002
The following article is Free article
Kristen Alanis, Zuzanna S. Siwy and Lane A. Baker
099003
The following article is Open access
Andrei Kulikovsky