Batteries, Fuel Cells, and Energy Conversion
A395
K. Funke, B. Heimann, M. Vering and D. Wilmer
In fragile glass-forming ionic melts, spectra of the ionic conductivity have been taken in wide ranges of frequency and temperature. In our experiments, we have studied
and
over more than ten decades on the frequency scale, including the far infrared. The results exhibit characteristic traits, and a clear-cut picture is found to emerge from them. We present a phenomenological description of our data as well as a set of equations which fit them surprisingly well. Those equations are then traced back to their dynamic origins on atomic scales of length and time. The underlying dynamic principle which is thus revealed is called the concept of mismatch and relaxation (CMR). © 2001 The Electrochemical Society. All rights reserved.
A402
K. C. Hewitt, L. Y. Beaulieu and J. R. Dahn
Ballmilling of In and Sb has been used to produce InSb for use in electrochemical and in situ X-ray diffraction studies (XRD) of
ethylene carbonate:diethyl carbonate/InSb cells. The cell capacity decays rapidly when cycled between 0 and 1.3 V, while the capacity reduction is less pronounced when cycling is restricted to the 0.65-1.4 V range. In situ XRD studies reveal that
and In are formed during the first plateau (above 0.65 V), according to the reaction
The indium product subsequently reacts with Li forming the
phases InLi and
in sequence. When cells are cycled above 0.6 V (i.e., in the absence of
formation) capacity retention improves significantly, remaining relatively constant near 250 mAh/g. Detailed in situ XRD studies of these cells suggest that 0.27 Li atoms per InSb may be intercalated during a sharp drop in the cell potential, according to the reaction 
This intercalation accounts for only a small (about 30 mAh/g) fraction of the overall capacity of 680 mAh/g. Consequently, it appears that the reactivity of In and Sb with Li, not the structure type, determines the reaction path. Therefore, InSb is not an attractive intercalation host for Li, in contrast to the claims made in the literature. © 2001 The Electrochemical Society. All rights reserved.
A411
Göran Lindbergh, Marie Olivry and Mari Sparr
The electrochemical performance of the porous nickel anode in a molten carbonate fuel cell was experimentally investigated in this study. The electrode structure was studied by scanning electron microscope and Hg porosimetry. The effect of electrolyte filling, on overpotential at a constant current density, was also examined. Kinetics for the hydrogen reaction was studied by obtaining stationary polarization curves, for porous nickel anodes at varying temperatures and anode gas compositions. The slopes of these polarization curves were analyzed at low overpotentials, with the assumption that the porous anode was under kinetic control, and the corresponding exchange current densities were determined using a simplified porous electrode model. The obtained partial pressure dependencies of the exchange current density were high, and therefore, difficult to explain by the generally assumed mechanisms. © 2001 The Electrochemical Society. All rights reserved.
A418
G. Frenning, F. Engelmark, G. A. Niklasson and M. Strømme
A422
K. Dokko, M. Mohamedi, Y. Fujita, T. Itoh, M. Nishizawa, M. Umeda and I. Uchida
A427
Zhongliang Zhan, Ting-Lian Wen, Hengyong Tu and Zhi-Yi Lu
A433
M. J. Jørgensen and M. Mogensen
A number of lanthanum strontium manganate/yttria-stabilized zirconia (LSM/YSZ) composite electrodes are produced with varying composition and processing parameters. The composites are investigated using impedance spectroscopy. General trends related to the oxygen reduction process are extracted from the impedance data. Literature concerning kinetic studies of LSM/YSZ electrodes and related systems is reviewed and compared to new experimental data. From this it is found that at least five processes affect the impedance. Going from high to low frequency, these processes are (i), (ii) two geometry-related contributions interpreted as transport across LSM/YSZ interfaces and through the YSZ of the composite, (iii) a process reflecting competitive reaction steps such as bond breaking and surface diffusion,
gas diffusion in a stagnant gas layer above the electrode structure, and
an activation process (inductive) presumably located at the triple phase boundary of electrode, electrolyte, and gas phase. © 2001 The Electrochemical Society. All rights reserved.
A443
Seungdoo Park, Raymond J. Gorte and John M. Vohs
A448
R. Patrice, B. Gérand, J. B. Leriche, L. Seguin, E. Wang, R. Moses, K. Brandt and J. M. Tarascon
We present a study of the
reduction process leading to the second electron plateau occasionally occurring during the electrochemical discharge of
-based alkaline cells. The origin of the second plateau is nested in a dissolution-reduction-precipitation mechanism, and its onset potential is governed by
solution species through the Nernst law. Also, the appearance of this second plateau in
-based alkaline cells is a strong function of the nature of the counter electrode, and is, for instance, rarely observed when Zn slurries are used as the counter electrode. Direct experimental evidence, by means of in situ XRD, SEM, and EDX analyses, is given for the formation of the spinel
during the first electron reduction of
An ion exchange reaction is proposed to account for the formation of this phase. Based on these findings, we show that the likelihood of raising the second potential through chemical approaches, thereby using the second electron capacity in
-based alkaline cells, is low. © 2001 The Electrochemical Society. All rights reserved.
A456
Teruhisa Horita, Katsuhiko Yamaji, Natsuko Sakai, Harumi Yokokawa, André Weber and Ellen Ivers-Tiffée
A463
X. Zhang, P. N. Ross Jr., R. Kostecki, F. Kong, S. Sloop, J. B. Kerr, K. Striebel, E. J. Cairns and F. McLarnon
A baseline cell chemistry was identified as a carbon anode,
cathode, and diethyl carbonate-ethylene carbonate
electrolyte, and designed for high power applications. Nine 18650-size advanced technology development cells were tested under a variety of conditions. Selected diagnostic techniques such as synchrotron infrared microscopy, Raman spectroscopy, scanning electronic microscopy, atomic force microscopy, gas chromatography, etc., were used to characterize the anode, cathode, current collectors and electrolyte taken from these cells. The diagnostic results suggest that the four factors that contribute to the cell power loss are solid electrolyte interphase deterioration and nonuniformity on the anode; morphology changes, increase of impedance, and phase separation on the cathode; pitting corrosion on the cathode current collector; and decomposition of the
salt in the electrolyte at elevated temperature. © 2001 The Electrochemical Society. All rights reserved.
A471
Yongyao Xia, Tetsuo Sakai, Takuya Fujieda, Masashi Wada and Hiroshi Yoshinaga
A482
Seung-Taek Myung, Shinichi Komaba and Naoaki Kumagai
A490
S. Calabrese Barton and A. C. West
The mass-transfer-limited region of zinc electrodissolution in alkaline electrolyte was investigated using a zinc rotating disk electrode. Pseudo-steady-state polarization measurements reflect a strong dependence of dissolution rate and shape of the limiting current plateau on composition and mass transfer rate. Electrochemical impedance spectroscopy results show that there is no appreciable dependence of the high frequency resistance on potential or rotation speed at prepassive potentials. Electrohydrodynamic impedance measurements, together with a simple model, suggest that the zincate ion is the appropriate mass transfer-limited species in this range, although the diffusion coefficients estimated from these analyses are lower than expected. © 2001 The Electrochemical Society. All rights reserved.
A496
H. Hoster, T. Iwasita, H. Baumgärtner and W. Vielstich
Smooth ultrahigh vacuum-cleaned PtRu alloys used as model catalysts for methanol oxidation, present a continuous loss of activity under potentiostatic conditions. After a potential step, e.g., from 50 to 500 mV vs. reference hydrogen electrode, chronoamperometric curves first show a steep decrease over 5-10 min followed by a slower decrease over several hours. The latter decay exhibits a time−1 behavior for different catalyst compositions, with higher slopes for the catalysts with less activity. The first current decay can be repeatedly observed by restarting the experiment after setting the potential back to the initial value, thus indicating a certain degree of reversibility. The slow decrease in activity, however, cannot be recovered by this means. But stepping the potential to higher anodic values, e.g., up to 1.2 V, the original surface activity can be obtained again. Optimized porous PtRu surfaces, on the other hand, do not show any comparable decrease after a respective potential step. The possible origin of the different behavior of smooth and porous surfaces is discussed. © 2001 The Electrochemical Society. All rights reserved.
A502
W. Vielstich, V. A. Paganin, F. H. B. Lima and E. A. Ticianelli
Potentiostatic investigations of the methanol oxidation in the absence and presence of oxygen at the three-phase boundary of a Pt-catalyzed gas diffusion electrode were carried out at several electrode potentials. In the presence of oxygen, a purely chemical reaction between oxygen and methanol was observed, with the products being
and water. A study of the rate of
formation and of the electrochemical currents for methanol oxidation showed that the rate of fuel consumption at the electrode is strongly increased by this chemical pathway. This is accompanied by a considerable decrease in the electrochemical currents for oxygen reduction. In the absence of oxygen and for potentials above 1.1 V vs. RHE, current oscillations were observed during the anodic process, which were attributed to the formation of an unstable layer of surface platinum oxides. © 2001 The Electrochemical Society. All rights reserved.
A506
Rajendra N. Basu, Orhan Altin, Merrilea J. Mayo, Clive A. Randall and Semih Eser
A high-quality fugitive pyrolytic carbon (PyC) film is used as an interlayer material in fabricating solid oxide fuel cells (SOFCs) by electrophoretic deposition (EPD). The carbon must both be highly conducting and burn away cleanly; hence, a graphitic or pyrolytic carbon is required. In this investigation, optimum conditions for PyC deposition from propylene pyrolysis (i.e., CVD) were ascertained. Propylene was decomposed at temperatures of 725, 775, and 825°C and at 1 atm pressure with different residence times (10-20 s) onto a porous
tube surface. Depending on the temperature and residence time, two different ranges of carbon deposit reactivities were obtained, corresponding to disordered and ordered carbon states, respectively. Temperature-programmed oxidation, scanning electron microscopy, and micro-Raman spectroscopy analyses indicate that the creation of uniform and sufficiently thick films with the highest degree of atomic ordering occurs at temperatures between 725 and 775°C and a gas residence of about 14 s. Notably, the same carbon deposition conditions produced crack-free and gastight YSZ films (15-20 μm) during the fabrication of SOFCs by EPD and subsequent sintering. © 2001 The Electrochemical Society. All rights reserved.
A513
C. Hasiotis, Li Qingfeng, V. Deimede, J. K. Kallitsis, C. G. Kontoyannis and N. J. Bjerrum
A520
Y. Arachi, T. Asai, O. Yamamoto, Y. Takeda, N. Imanishi, K. Kawate and C. Tamakoshi
Corrosion, Passivation, and Anodic Films
B163
V. Guillaumin, P. Schmutz and G. S. Frankel
A variety of interfaces relevant to corrosion processes were examined by the scanning Kelvin probe force microscopy (SKPFM) technique in order to study the influences of various parameters on the measured potential. SKPFM measurements performed on AA2024-T3 after solution exposure showed that surface composition is not the only parameter that controls the Volta potential difference, which is measured by SKPFM. The influence of surface oxide structure and adsorption at the oxide surface can be probed by SKPFM and lateral potential gradients can be observed in the absence of significant differences in oxide composition. The influence of tip-sample separation distance on the measured Volta potential difference was studied for different pure oxide-covered metals. SKPFM measurements were made in air on pure Ni and Pt samples withdrawn from solution at open circuit or under potential control. The Volta potential difference was found to be composed of a transient component that slowly discharged and a more permanent component associated with the charge of adsorbed species. The Volta potential difference transients measured on the samples emersed under potential control decayed much slower than the open-circuit potential transient measured in solution upon release of the potential control. These different measurements validate the use of SKPFM for the prediction of local corrosion sites and the study of surface modification during solution exposure. © 2001 The Electrochemical Society. All rights reserved.
B174
T. Suter, E. G. Webb, H. Böhni and R. C. Alkire
The onset of pitting corrosion at MnS inclusions on 304 stainless steel in 1 M NaCl was studied with and without applied mechanical stress with use of microelectrochemical cells. Polarization curves of areas (100 μm diam) without inclusion showed no pitting at potentials below that of oxidation evolution; stress had no effect on the corrosion behavior. Areas containing five round inclusions of about 4 μm in size showed stable pitting at about 400 mV; the effect of stress shifted the pitting potential to values that were 150 mV more negative. Polarization curves measured on large deep MnS inclusions showed active pitting. Curves of areas with single large, shallow MnS inclusions showed multiple current transients during dissolution of the inclusion without stress, but the metastable events did not initiate stable pitting. The dissolution of shallow MnS inclusion did not form a deep microcrevice between the MnS and stainless steel matrix. However, under applied stress, cracks were formed within the shallow MnS inclusion and active pitting occurred. To explore whether such cracks might serve to generate locally high concentrations of aggressive species, the pH and chloride concentration inside a crack were simulated using a finite difference model. For experimental conditions where stable pitting was observed, the simulations predicted that the solution composition at the base of a typical 13 μm deep crack correspond to a pH of around 2, and a chloride concentration of about 6 M led to stable pitting. © 2001 The Electrochemical Society. All rights reserved.
B186
E. G. Webb, T. Suter and R. C. Alkire
A combination of mathematical modeling and experiments on single MnS inclusions was used to investigate the role of MnS inclusions on the initiation of pitting corrosion of 304 stainless steel. Isolation of single MnS inclusions in chloride-containing solutions with use of microcapillaries as electrochemical cells showed that the orientation of the MnS inclusion played a significant role in pit initiation. Large, shallow MnS inclusions failed to initiate pitting corrosion, while the same inclusions, oriented narrow and deep, consistently exhibited the onset of localized corrosion. The formation of a microcrevice was observed between the dissolving MnS inclusion and stainless steel. The microcrevice resulted in a locally occluded region where aggressive ions can accumulate. A mathematical model was developed to explore the local chemistry within a one-dimensional microcrevice of which one wall was MnS and the other was stainless steel. The results of the simulations supported the view of a critical solution chemistry of sulfur species, in a chloride environment, as a possible trigger mechanism for localized corrosion. A critical microcrevice geometry of approximately 1 μm was predicted to be sufficiently large to generate stable pitting in the system under study. © 2001 The Electrochemical Society. All rights reserved.
B196
G. O. Ilevbare and J. R. Scully
Oxygen reduction reaction (ORR) kinetics were investigated on bulk synthesized analogues of Al-Cu, Al-Cu-Mg, and Al-Cu-Fe-Mn intermetallic phases with and without chromate conversion coating (CCC) in 0.1 M
M NaCl (pH 6) with minimal levels of total dissolved chromate. The results were compared to AA 2024-T3 and high purity Al, Cu, Cr, and Au. Net cathodic ORR mass transport-limiting current densities of Al-based materials, lacking large quantities of Fe, Mn, or Cu were lower than the theoretically predicted rates in the mass transport controlled regime of ideal electronic conductors. This suggests a second rate-limiting factor in the case of these Al-based materials that was deduced to be related to Al-rich surface oxides. A second rate-limiting effect was also seen for pure Cr, implying that
inhibits ORR kinetics. CCC inhibited open circuit corrosion, via reduced ORR kinetics. It also serves as a diffusive barrier to
transport. The role(s) of CCC as an enhanced electronic barrier to electron transfer or barrier to
chemisorption remains unclear. © 2001 The Electrochemical Society. All rights reserved.
B208
Houyi Ma, Shenhao Chen, Lin Niu, Shuxia Shang, Shulan Li, Shiyong Zhao and Zhenlan Quan
The electrochemical behavior of copper in the aerated 0.5 mol dm−3 sodium bromide solutions with or without a Schiff base,
-phenylen-bis(3-methoxysalicylidenimine) (V-o-Ph-V) were investigated by means of the steady-state polarization and impedance techniques. V-o-Ph-V acted as a mixed-type inhibitor in NaBr media, and it adsorbed easily on the copper surface at potentials near the corrosion potential. The adsorbed V-o-Ph-V formed a thin protective film which reduced both anodic and cathodic reaction rates significantly. The impedance spectra for copper measured at the corrosion potentials in the presence of V-o-Ph-V displayed two capacitive loops due to different influences of the protective film on the anodic and cathodic reactions occurring at the copper surface. V-o-Ph-V could self-assemble on the copper surface and the self-assembled film also exhibited a good inhibition on copper in halide solutions. The dissolution mechanism of copper and the inhibition mechanism of V-o-Ph-V on the copper in NaBr solution are interpreted. In addition, the inhibiting action of V-o-Ph-V is compared with that of the other two Schiff bases,
-phenylen-bis (3-methoxysalicylidenimine) (V-p-Ph-V) and N-[(2-hydroxy-3-methoxyphenyl)methylene]-histidine (V-His) in order to investigate the effect of Schiff bases’ geometric structures on their inhibition ability. © 2001 The Electrochemical Society. All rights reserved.
Electrochemical/Chemical Deposition and Etching
C327
Wei-Tsu Tseng, Chia-Hsien Lo and Shih-Chin Lee
C333
Wei-Tsu Tseng, Chia-Hsien Lo and Shih-Chin Lee
C339
Mary Ellen Biggin and Andrew A. Gewirth
The potential-dependent behaviors of benzotriazole (BTAH) and 1-(methoxymethyl)-1H-benzotriazole (MeOMe-BTA) on copper surfaces were studied by cyclic voltammetry and in situ polarization modulation infrared reflection absorption spectroscopy. The identity of the anion in the supporting electrolyte has a significant effect on the formation and decomposition of the Cu(I)BTA multilayer surface complex. In chloride-containing solution, the Cu(I)BTA film is more easily formed. This film can be completely reduced upon excursion to more negative potentials. In sulfuric acid solution, the Cu(I)BTA film is formed less readily at more positive potentials and cannot be completely reduced at more negative potentials. The differences in the film formation/decomposition in the two electrolytes are attributed to coordination of the anion
or
to the Cu(I) center of the Cu(I)BTA complex. Secondary ion mass spectrometric results also show that the anion coordination changes the amount of specific elements incorporated into the copper electrodeposit. MeOMe-BTA does not form a complex with copper due to blockage of one of the triazole ring nitrogens, and its electrochemical behavior is not affected by the anion identity. © 2001 The Electrochemical Society. All rights reserved.
C348
X. H. Xia and J. J. Kelly
C353
Chee Won Chung and Ilsub Chung
C357
M. Innocenti, G. Pezzatini, F. Forni and M. L. Foresti
We applied the electrochemical atomic layer epitaxy (ECALE) methodology to obtain deposits of CdS and ZnS on Ag(111) by alternate underpotential deposition of the elements forming the compounds. The amounts of the elements deposited, determined by stripping coulometry, always yielded a stoichiometric 1:1 ratio. The deposits were formed using an automated electrochemical deposition system, described here, making use of a simple distribution valve. © 2001 The Electrochemical Society. All rights reserved.
C363
Wiehua Wang, Mark R. Holl and Daniel T. Schwartz
A flexible and inexpensive approach for rapid prototyping of thick masks (∼130 μm in height) for through-mask electrodeposition of metallic microstructures is demonstrated. The electrodeposition masks are fabricated directly from a computer-aided design layout by patterning adhesive-backed polyvinyl chloride tape using a
laser. The pliant tape masks can then be transferred directly to planar or nonplanar substrates. We demonstrate the use of the tape mask on a nonplanar substrate by plating a NiFe microcoil on a cylindrical rod. The pattern transfer characteristics of the tape mask are illustrated by plating copper columns on a platinum rotating disk electrode. We also fabricate a two-level NiFe criss-cross structure to show how these tape masks can be used to build structures in three dimensions. Limitations of the existing laser system permit minimum lateral feature dimensions of 130 μm, though the method developed here should readily scale down in feature dimensions using a higher energy pulsed laser. © 2001 The Electrochemical Society. All rights reserved.
C369
T. Hernández-Pérez, M. Morales, N. Batina and M. Salmón
The surface morphology of polypyrrole (ppy) films prepared by potentiostatic and voltammetric methods at the platinum electrode was studied by ex situ atomic force microscopy (AFM). The study was mainly focused on the early stages of polymer film growth up to a film thickness of 30 to 50 nm. AFM analysis revealed that polymer film morphology depends on the electrosynthesis method used. Electrosynthesized films produced by the voltammetric method consisted of nano-size ppy nodules, which during the polymer oxidation process become associated forming larger surface aggregates. However, in thicker films and those prepared using a large anion, this association was not observed. The ppy films formed by the potential step method (potentiostatic) allowed a better control of the early stages of the electropolymerization process. Thus, the AFM study showed that the first ppy nodules grow three-dimensionally during the application of the potential pulse steps, and simultaneously their number increase on the electrode surface according to the progressive nucleation and growth model. Negligible association of ppy nodules was noticed for the film prepared by the potentiostatic method, which suggests that this synthesis method is a better alternative for controlling ppy film growth. © 2001 The Electrochemical Society. All rights reserved.
C376
Yang Cao, Peter C. Searson and Alan C. West
Direct numerical simulations, using a boundary integral method, are used to investigate nucleation followed by diffusion-limited growth during electrochemical deposition. Results are compared to three published models. For instantaneous nucleation, the theories are in good agreement with simulations. Errors are more significant for finite nucleation rates for two published theories, while the theory of Mirkin and Nilov is in very good agreement with simulations. The evolution in time of the standard deviation in cluster size due to the apparently random nature in space and time of nucleation is presented. The advantages and possible extensions of the simulation approach are also discussed. © 2001 The Electrochemical Society. All rights reserved.
C383
Kwang Chul Kim, Chan Il Park, Jae Il Roh, Kee Suk Nahm, Yoon Bong Hahn, Youn-Sik Lee and Kee Young Lim
Single crystal cubic SiC(100) thin films were grown on Si(100) from thermal cracking of tetramethylsilane (TMS) as a function of growth temperature, reactor pressure, source gas flow rate, and Si/C atomic ratio in a radio frequency-inductive chemical vapor deposition reactor. The orientation of as-grown SiC films mostly followed that of the Si substrate. However, the growth of SiC(111) was detected in the films grown at high TMS flow rates and high Si/C atomic ratios. The thickness of the SiC film was increased with the growth temperature, reactor pressure, TMS flow rate, and Si/C atomic ratio. Voids were formed in the silicon side of the SiC/Si interface, but disappeared when the reactor pressure, TMS flow rate, and Si/C ratio were increased. The formation of voids was attributed to the outdiffusion of Si atoms from the Si substrate. The stresses and strains generated in the grown films were also investigated in terms of the growth conditions. The formation mechanism of voids at the SiC/Si interface was discussed on the basis of the experimental observations. © 2001 The Electrochemical Society. All rights reserved.
C390
Carol Thompson, G. B. Stephenson, J. A. Eastman, A. Munkholm, O. Auciello, M. V. Ramana Murty, P. Fini, S. P. DenBaars and J. S. Speck
We apply synchrotron X-ray analysis techniques to probe the surface structure of GaN films during synthesis by metallorganic chemical vapor deposition (MOCVD). Our approach is to observe the evolution of surface structure and morphology in real-time using grazing incidence X-ray scattering (GIXS). This technique combines the ability of X-rays to penetrate the chemical vapor deposition environment for in situ measurements, with the sensitivity of GIXS to atomic scale structure. Examples are presented from some of our studies of growth modes and surface evolution as a function of process conditions that illustrate the capabilities of synchrotron X-ray analysis during MOCVD growth. We focus on studies of the homoepitaxial growth mode, island coarsening dynamics, and effects of impurities. © 2001 The Electrochemical Society. All rights reserved.
C395
Qun Zhu and Charles L. Hussey
Electrochemical Synthesis and Engineering
D49
İ. Becerı˙k and F. Kadirgan
Cyclic voltammetry combined with X-ray photoelectron spectroscopy measurements were utilized to explore the kinetic of the electro-oxidation of formic acid on dispersed platinum and perchlorate doped polypyrrole film electrodes. Experimental conditions for the preparation of the electrocatalytic system were determined. Results strongly suggest the doping effect on the reaction mechanism. © 2001 The Electrochemical Society. All rights reserved.
D55
Z. Yoshida, H. Yosue and G. Nogami
D60
M. A. Rodrigo, P. A. Michaud, I. Duo, M. Panizza, G. Cerisola and Ch. Comninellis
The electrochemical behavior of synthetic boron-doped diamond thin-film electrode (BDD) has been studied in acid media containing 4-chlorophenol (4-CP) by cyclic voltammetry, chronoamperometry, and bulk electrolysis. The results have shown that in the potential region of supporting electrolyte stability occur reactions involving the oxidation of 4-CP to phenoxy radical and 1,4-benzoquinone. Polymeric materials, which result in electrode fouling, are also formed in this potential region. Electrolysis at high anodic potentials, in the region of electrolyte decomposition, complex oxidation reactions can take place involving electrogenerated hydroxyl radicals, leading to the complete incineration of 4-chlorophenol. Electrode fouling is inhibited under these conditions. The experimental results have been also compared with a theoretical model. This model is based on the assumption that the rate of the anodic oxidation of 4-CP is a fast reaction. Finally, high-pressure liquid chromatographic analyses revealed that the main intermediate products of 4-CP oxidation were 1,4-benzoquinone, maleic acid, formic acid, and oxalic acid. © 2001 The Electrochemical Society. All rights reserved.
D65
Ming-Sieng Wu, Ten-Chin Wen and A. Gopalan
Physical and Analytical Electrochemistry
E177
C. Cachet-Vivier, V. Vivier, C. S. Cha, J-Y. Nédélec and L. T. Yu
Taking the electrocatalytic hydrogenation of ethylene as an example, we show that the cavity microelectrode allows the study of the surface processes occurring on powder materials. The electrocatalytic current can be observed at scan rate
up to a few tens of mV s−1, while with a standard composite electrode,
must be lower than a few fractions of mV s−1. The extent of the scan rate range is around two to three magnitudes. Therefore, it is possible to construct significant voltammogram characteristics (peak intensity, peak potential, and peak area) scan rate profiles, which are related to processes underlying the electrocatalysis. However, their quantitative exploitation needs a theoretical model, which can be built up by (i) applying the chemical and electrochemical kinetics to the various involved processes and (ii) taking into account the geometry proper to a composite electrode. Direct analysis of the model allows qualitatively explaining the variation of the ratio electrolytic-current/H chemisorption current observed on cavity microelectrode vs. the scan rate, when compared to that of the spherically shaped platinum electrode. © 2001 The Electrochemical Society. All rights reserved.
E183
Xuerong Zhang, James K. Pugh and Philip N. Ross
Ethers and organic carbonates are commonly used as solvents in lithium battery electrolyte. It is important to determine the oxidation potentials of these organic solvents due to the high cathode potential (∼5 V) in many of these batteries. There are significant variations in the reported oxidation potentials for electrolytes containing these solvents. The factors contributing to the variation include the type of salt used in the electrolyte, composition of the electrode, and a somewhat arbitrary determination of the oxidation potential from the anodic cutoff current. We report here the application of density functional theory (DFT) to calculate solvent oxidation potentials assuming oxidation occurs via one-electron transfer to form the radical cation. No specific ion-ion, ion-solvent, or ion-electrode interactions are included. These values are then compared to the experimental observations. Eleven solvent molecules are studied: 1,2-dimethoxyethane, tetrahydrofuran, 1,3-dioxolane, diethylcarbonate, dimethylcarbonate, ethylmethylcarbonate, ethylene carbonate, propylene carbonate, butylene carbonate, vinylene carbonate, and catechol carbonate. Optimized geometries of the radical cations correlate well with the fragmentation patterns observed in mass spectrometry. The oxidation potentials of saturated carbonates are calculated to be approximately 1 V higher than the organic ethers, which is consistent with reported literature values. Quantitative comparison with experiment will require more careful measurements to eliminate other oxidation reactions and a standardized procedure for determining the oxidation potential. © 2001 The Electrochemical Society. All rights reserved.
E189
D. Tsiplakides and C. G. Vayenas
A two-Kelvin-probe arrangement was used to measure, for the first time in situ, the work functions, Φ, of the gas-exposed surfaces of porous Pt, Au, and Ag working and reference electrodes exposed to 
and
mixtures, and deposited on 8%
-stabilized
(YSZ) in a three-electrode solid electrolyte cell. It was found that at temperatures above 600 K the potential difference,
between the working (W) and reference (R) electrode reflects the difference in the actual, spillover, and adsorption-modified work functions,
and
of the two electrodes

This equation, typically valid over 0.8-1 V wide
ranges, was found to hold for any combination of the Pt, Au, and Ag electrodes. It is consistent with the previously reported equation

which is also confirmed here, and allows for the definition of a natural absolute electrode potential
in solid-state electrochemistry from

where Φ is the work function of the gas-exposed electrode surface of the metal (any metal) electrode in contact with the YSZ solid electrolyte. It expresses the energy of solvation of an electron from vacuum to the Fermi level of the solid electrolyte. The value
V was determined as the standard
value at
and
K. © 2001 The Electrochemical Society. All rights reserved.
E203
Keqin Huang and John B. Goodenough
E215
Guofeng Li, Mira Josowicz and Jiřı́ Janata
E219
Toru H. Okabe, Akiyoshi Horiuchi, Kallaracke T. Jacob and Yoshio Waseda
E227
Zhiliang Cheng, Long Cheng, Shaojun Dong and Xiurong Yang
Ultrathin multilayer films of a polybasic lanthanide heteropoly tungstate-molybdate complex and a cationic polymer of quaternized poly(4-vinylpyridine) partially complexed with osmium bis(2,2′-bipyridine) have been fabricated on a gold electrode precoated with a cysteamine self-assembled monolayer. The multilayer films have been characterized by optical spectroscopy, small-angle X-ray diffraction, and electrochemical methods (cyclic voltammetry and electrochemical impedance). Especially, the electrochemical impedance spectroscopy is developed to monitor the layer deposition processes. It provides important information such as double-layer capacitance and charge-transfer resistance. All obtained results reveal regular film growth with each layer adsorption. © 2001 The Electrochemical Society. All rights reserved.
E233
K. Darowicki, A. Krakowiak and A. Zieliński
Spectral analysis was carried out by Fourier and Gabor transformation of a nonstationary process. It is shown that spectral analysis by Gabor transformation correctly reflects the analyzed signal of varying spectral composition. Fourier transformation is an averaged spectral characteristic. Spectral analysis of anodic current oscillations of copper dissolution in sulfate solution was performed. It was found that current oscillations are a composition of three simple oscillators. The intensity of frequency bands decreases with time. Instantaneous frequencies of each band also decrease in the function of time. Spectral analysis by the Fourier method does not correctly reflect the real changes of analyzed oscillations. Gabor transformation accurately reflects oscillation changes in time. This type of spectral analysis is a useful tool in the analysis of electrochemical oscillations. © 2001 The Electrochemical Society. All rights reserved.
E237
Peter K. LeMaire, Rodney Speel and Rick Ruotolo
is one of a family of amorphous mixed ionic electronic conductors
(A = Cu, Ag, and x between 2.8 and 4.0). This work extends the electrical transport measurements over a temperature range 170 to 440 K. Direct current four-probe transient methods were used to acquire voltage vs. time profiles of the material, and the ionic and electronic conductivities, and the chemical diffusion coefficients obtained following Yokota’s model for mixed conductors. Differential scanning calorimetry showed phase transitions at about 411 and 451 K. Variations in the electrical transport measurements at around 400 K seem to corroborate the first phase transition. Thermogravimetric analysis shows no decomposition of the material up to about 600 K. The ionic conductivity over the entire temperature range is of the Arrhenius form, supporting hopping as the mode of ionic transport, with an activation energy of about 0.25 eV, and jump and residence times of the order of
and
s, respectively. The electronic conductivity results suggest possible variable range hopping between localized states, in support of earlier results obtained from the estimate of the electronic diffusion. The chemical diffusion coefficients were also of the Arrhenius form, with an activation energy of about 0.24 eV. © 2001 The Electrochemical Society. All rights reserved.
Dielectric Science and Materials
F83
Dong-Soo Yoon, Kwon Hong and Jae Sung Roh
The effect of various post-treatment temperatures on the oxidation behavior of a TiN diffusion barrier was investigated as a function of a two-step annealing. Both the Ru-O/Ru/TiN/poly-Si/Si and BST/Ru-O/Ru/TiN/poly-Si/Si structures retained their structure without an increase in resistivity even after annealing at 550°C and the two-step annealing, while for both the
and
structures, the degradation is started after annealing at 400°C. In the latter case, the
film was a porous amorphous structure, no formation of a thin
layer, and many voids, resulting from free diffusion of oxygen and oxidation of TiN diffusion barrier. Meanwhile, in the former case, the role of the thin
oxidized layer formed at the surface of Ru film after annealing at 400°C leads to the strongly stuffed along the grain boundaries as well as matrix and the formation of chemically strong bonds with Ru-O. At 400°C and after the two-step annealing, the conductive
phase is formed at the surface of Ru film, giving rise to oxygen sink layer. In addition, the BST/Ru-O layer leads to confusion of the oxygen indiffusion through the BST/Ru-O layer during annealing at 420°C for 5 min in oxidizing ambient, followed by a suppression of oxygen indiffusion and an improvement of TiN barrier properties. Therefore, both the Ru-O/Ru/TiN/poly-Si/Si and BST/Ru-O/Ru/TiN/poly-Si/Si systems for broadening the process window of a sputtered TiN diffusion barrier are better than the
and the
systems. © 2001 The Electrochemical Society. All rights reserved.
F92
A. A. Efremov, V. G. Litovchenko, G. Ph. Romanova, A. V. Sarikov and C. Claeys
Physical mechanisms of oxygen transport and precipitation in silicon during the synthesis of buried oxide layers are reviewed. Different effects caused by the interaction of weakly bonded oxygen with mobile point defects and static defect complexes are analyzed. As a result, the possibility of controlling the evolution of the spatial distribution of implanted oxygen by means of gettering and defect engineering are studied and validated by computer simulations based on a quasi-chemical description of the kinetics. Special attention is given to carbon induced gettering mechanisms involved in the buried oxide synthesis known as low-dose approach combined with defect engineering. Secondary ion mass spectroscopy profiling data together with the results of computer simulations show a rather complicated behavior of the carbon and point toward an important role of the carbon-vacancy and carbon-oxygen complexes in the oxygen accumulation. Some effects in the early stage of the oxygen redistribution are revealed and discussed. The influence of an inhomogeneous distribution of bonded oxygen in silicon on the yield of different single atomic and cluster secondary ions (SIs) during oxygen sputtering is studied. The role of different oxygen containing phases in SI formation is discussed. It is shown that carbon acts on
precipitates not only in a local but also in a global manner. © 2001 The Electrochemical Society. All rights reserved.
F98
I. Matthew and M. Tomozawa
The influence of fictive temperature on the polishing characteristics of amorphous silicon dioxide films was studied. Amorphous materials, in general, can have different properties depending upon their thermal history, and this is attributed to a difference in their fictive temperature, the temperature at which the supercooled liquid structure freezes into a glass. Amorphous silicon dioxide films ca. 2 μm thick, were prepared by wet thermal oxidation, dried, and then heat-treated to have different fictive temperatures. Indentation testing of similarly heat-treated silica glasses, done using nanoindentation and a Knoop microhardness indenter, showed that the glass with a higher fictive temperature had a higher hardness. On the other hand, the chemical etch rate in dilute hydrofluoric acid was faster for the silica glass with the higher fictive temperature. Polishing of the silicon dioxide films using cerium oxide slurry under identical conditions showed that the polishing rate was higher for the oxide films with a lower fictive temperature. Hence, it was suggested that the mechanical properties of the glass were more important than chemical properties in controlling the polishing behavior of amorphous silicon dioxide. © 2001 The Electrochemical Society. All rights reserved.
F102
Sairam Agraharam, Dennis W. Hess, Paul A. Kohl and Sue Ann Bidstrup Allen
Fluorocarbon films were deposited from pentafluoroethane/argon plasmas in a parallel plate reactor at operating pressures of 0.75 and 1 Torr, substrate temperatures of 120, 180, and 240°C, and applied powers between 10 and 30 W. These films were subjected to an 85°C and 85% relative humidity environment for 100 h to assess reliability. Infrared spectroscopy showed no change in the bulk structure and composition of the deposited films after temperature-humidity exposure. Also, no OH related peaks were detected in the infrared spectrum, suggesting negligible moisture absorption. Indeed, moisture absorption studies showed less than 0.15 wt % increase for the investigated deposition conditions, as measured by a quartz crystal microbalance. Furthermore, humidity cycling studies indicated no chemisorption of water by the deposited films. Capacitance measurements of the fluorocarbon films yielded a dielectric constant ranging between 2.23 and 2.55 and a loss tangent on the order of
The dielectric constant increased with an increase in deposition temperature and a decrease in operating pressure. The dielectric constant of the fluorocarbon films did not change after exposure to the 85°C/85% relative humidity environment, further confirming the IR and moisture absorption results. However, X-ray photoelectron spectroscopy (XPS) of the fluorocarbon films indicated a decrease in the F/C ratio and an increase in the O/C ratio after temperature-humidity exposure, which suggests that defluorination and oxidation occur primarily in the top few monolayers of the deposited films. C 1s spectral analysis indicated a decrease in the relative concentrations of 
CF, and
moieties and a dramatic increase in the C-C/C-H concentrations. These changes were attributed to the formation of a thin layer of low molecular weight oxidized material, which could be dissolved by rinsing the film in an ethanol ultrasonic bath. © 2001 The Electrochemical Society. All rights reserved.
Semiconductor Devices, Materials, and Processing
G237
Seung-Youl Kang, Kwang-Ho Kwon, Sung-Ihl Kim, Sang-Kyun Lee, Moon-Youn Jung, Young-Rae Cho, Yoon-Ho Song, Jin Ho Lee and Kyoung-Ik Cho
G241
Geun-Min Choi and Tadahiro Ohmi
In this study, the removal efficiency of metallic impurities with various substrate surfaces has been investigated. It strongly depends on the substrate conditions as well as the kind of metallic impurities. Copper (Cu) impurities deposited on an amorphous silicon (a-Si) surface are hardly removed by a hydrofluoric acid-hydrogen peroxide mixture (FPM) cleaning, while they are completely removed from a single crystalline silicon (c-Si) surface at a level lower than the detection limit. A hydrofluoric acid-hydrogen peroxide mixture with nonionic surfactant (FPMS) cleaning with high HF concentration, however, can efficiently remove Cu contaminants from both c-Si and a-Si surfaces. We postulate that both etching of the silicon by the FPM solution and surface passivation by the surfactant are essential to removing Cu contaminants from a-Si surface. Moreover, the Cu removal efficiency of FPMS solution is highly dependent on the nature of a-Si films. The range of high removal efficiency on a-Si film surface with inactivated phosphorus, when changing the chemical mixing ratio of an FPMS solution with 50 ppm nonionic surfactant, is much broader than that on undoped a-Si film surfaces, whereas it is not depending on the presence of hydrogen in a-Si film. In order to remove metallic impurities from all substrates including various a-Si film surfaces, a cleaning solution should have the etching capability of substrates and high dissolution rate of metallic contaminants. Much more attention should be given for HF-based solution process of various substrates with high etching rate. © 2001 The Electrochemical Society. All rights reserved.
G249
Katsushi Ohshika, Tomoko Yamashita, Munetoshi Fukui, Hiroshi Yanazawa, Shinichiro Takatani and Hidetoshi Matsumoto
G254
Ji-Myon Lee, Sang-Woo Kim and Seong-Ju Park
Nonselective dry etching of GaN,
and their multiquantum wells (MQW) was examined using a
plasma at room temperature. The etching characteristics were studied as functions of
concentration, inductively coupled plasma power, and radio frequency table power. Nonselective etching of MQW using a
plasma was monitored by means of laser interferometric reflectance. Ga, In, and GaCl as well as CN were observed as group III and group V etch products, respectively, in the optical emission spectrum during plasma etching. By optimizing the
concentration in the gas mixture, the roughness on the etched surface and the sidewall of the MQW could be substantially reduced. These results indicate that
plasma chemistry, combined with a postannealing process for etch-damage recovery, is suitable for the fabrication of optoelectronic devices using GaN, InGaN, and GaN/InGaN MQW. © 2001 The Electrochemical Society. All rights reserved.
G258
Sam-Dong Kim, In-Seok Hwang, Jin-Koo Rhee, You-Seok Suh and Dae-Gyu Park
We examine effects of the process variables of
transistor gate structures on material and electrical properties of
films and patterned polycide gate lines at sub-0.15 μm regime. The process variables include molar ratio of Si/Ti in composite
targets
2.2, 2.3, and 2.4), sputter deposition temperature, film thickness, rapid thermal annealing (RTA) process condition, and postannealing in a furnace. At high
Si precipitate formation is highly pronounced at the film surface as RTA temperature increases and contributes to the increase in surface roughness of the films. Moreover, processes of higher x targets show a greater number of add-on particles and more retarded
phase transformation. The RTA process after film deposition completely transforms 
films to
phase even at very fine lines when annealed at 800°C or higher for 20 s. The maximum thermal budget allowed for
postannealing is 800°C for 60 min, where no appreciable thermal degradation is shown in bar resistance regardless of target composition. At this postannealing condition, excellent bar resistance (∼4.4 Ω/□) and thermal stability are shown at 0.12 μm linewidth when
films were sputtered at 200°C.
films sputtered at 500°C show a stronger (040) C54 preferred orientation and greater degraded thermal stability than the films deposited at 200°C, and exhibit a bar resistance of ∼5 Ω/□ at 0.12 μm linewidth. © 2001 The Electrochemical Society. All rights reserved.
G265
Michele L. Ostraat, Jan W. De Blauwe, Martin L. Green, L. Douglas Bell, Harry A. Atwater and Richard C. Flagan
G271
Ming Qin, Vincent M. C. Poon and Stephen C. H. Ho
G275
Hei Wong, M. C. Poon, Yong Gao and Ted C. W. Kok
In this work, we develop methods for fabricating high quality dielectric films for nonvolatile memory applications. Oxide/Si-rich nitride/oxide structures are fabricated where the Si-rich nitride layer was deposited by the low pressure chemical vapor deposition (LPCVD) technique. With a Si-rich nitride layer, the Fowler-Nordheim tunneling voltage can be cut down to 3 V for oxide thickness of about 100 Å. By reoxidizing the Si-rich nitride layer, secondary ion mass spectroscopy study reveals that the hydrogen content of nitride film and its interface can be reduced by more than 40%. With this method, high nitrogen content oxynitride and smoother oxynitride/oxide interfaces result and the interface charge trapping can be improved remarkably. © 2001 The Electrochemical Society. All rights reserved.
G279
V. V. Afanas’ev and A. Stesmans
G283
Ming-Wen Wang and Fu-Chu Chou
G291
Sang-Wook Park, Dong-Jin Kim, Cha-Deok Dong, Noh-Yeal Kwak, Young-Taek Kong, Chan-Ho Lee, Seung-Cheol Lee, Se-Ho Park, Jong-Woo Kim and Hong-Seon Yang
This paper describes the effect of annealing on the characteristics of cycling endurance and charge retention in flash electronically erasable programmable read-only memory (EEPROM) fabricated by self-aligned source (SAS) dry etching process which was used for the shrinkage of cell size. The annealing process was used for the recovery and thickness compensation of the tunnel oxide edge at which severe plasma damage was accumulated during the SAS dry etching process. Through the analysis of cycling endurance, it was clarified that charge traps and structural defects were generated at the tunnel oxide edge during the SAS dry etching process and they induced the degradation of cycling endurance of memory cells. The characteristics of charge retention were improved due to the structural recovery and the thickness compensation of the tunnel oxide edge. An analysis of the results from the measurement of charge retention and the examination of the tunnel oxide edge with high resolution transmission electron microscope, indicates that the thickness compensation of the tunnel oxide edge affected more positively the reduction of tail bits than the structural recovery of the tunnel oxide edge. © 2001 The Electrochemical Society. All rights reserved.
General Topics
J25
Teruhisa Horita, Katsuhiko Yamaji, Natsuko Sakai, Harumi Yokokawa and Tohru Kato