ELECTROCHEMICAL SOCIETY LETTERS
L123
Joseph S. Shor and Richard M. Osgood Jr.
Wafer‐scale etching of
is demonstrated using UV‐lamp‐assisted photoelectrochemical etching in conjunction with photolithographically defined masks. The process exhibits high etch rates and dopant selectivity, features not available using other
etching methods.
L125
W. P. Kang and C. K. Kim
L128
Chang Wei and Krishnan Rajeshwar
L130
Pierre Boulas, Ramakrishnan Subramanian, Wlodzimierz Kutner, M. Thomas Jones and Karl M. Kadish
TECHNICAL PAPERS Electrochemical Science and Technology
2135
J. A. Bardwell, K. B. Clark, D. F. Mitchell, D. A. Bisaillion, G. I. Sproule, B. MacDougall and M. J. Graham
The anodic behavior of Si in dilute
solutions has been investigated with the aim of producing thin gate oxides of thickness between 4 and 15 nm. The oxide is formed under potentiostatic conditions and in varying solution concentrations. The thickness is calculated from x‐ray photoelectron spectroscopy (XPS) which has been calibrated with nuclear reaction analysis, using the 16O(d,p) 17O reaction. The anodic growth process yields very clean oxide, contaminated only with adventitious carbon on the surface as well as ≤1 at. percent nitrogen within the bulk (as detected by XPS). The nitrogen impurity is present in various oxidation states depending on the formation conditions. Its concentration can be decreased by annealing the samples, decreasing the concentration of
in solution, or by cathodic reduction. The growth mechanism has been investigated using the technique of 18O labeling with analysis by secondary ion mass spectroscopy.
2139
Bhasker B. Dave, Ralph E. White, Supramaniam Srinivasan and A. John Appleby
Effects of partial pressure of carbon dioxide and temperature on oxygen reduction kinetics on a gold electrode in a lithium carbonate melt were examined using electrochemical impedance spectroscopic (EIS) and linear sweep voltammetric techniques. The impedance spectra were analyzed by a complex nonlinear least squares method, using the Randles‐Ershler equivalent circuit model, to determine the electrode‐kinetic and the mass‐transfer parameters such as the charge‐transfer resistance and the Warburg coefficient. The cyclic voltammetric measurements indicated that the oxygen reduction process in lithium carbonate melt is “reversible” up to 200 mV/s. The product
determined by cyclic voltammetry agreed well with those estimated by the EIS method. The reaction order with respect to carbon dioxide and the activation energy for the exchange current density were determined to be −0.52 and 132 kJ/mol, respectively. Also, the reaction order with respect to carbon dioxide and the activation energy for
were calculated to be −0.8 and 185 kJ/mol, respectively.
2145
Thomas C. Franklin, Remi Nnodimele and Josef Kerimo
Copper(II) oxide and manganese(II) oxide were shown to be catalysts for the electro‐oxidation of 2‐chloroethyl ethyl sulfide, diethylsulfide, 2‐hydroxyethyl ethyl sulfide, and 1‐chlorobutane in aqueous suspensions containing cationic surfactants. These oxides were shown to act as catalysts by formation of copper(III), manganese(III), and manganese(IV) oxides which chemically oxidized the organic compounds. Analysis of the product suspensions showed the production of only the sulfoxide by oxidation of the 2‐chloroethyl ethyl sulfide and diethyl sulfide. Destruction of chlorobutane was catalyzed by both barium peroxide and copper(II) oxide. Volatile product(s) was trapped in a liquid nitrogen trap during electrolysis. These products included butane and butene.
2151
T. Kenjo, Y. Yamakoshi and K. Wada
The contact area between the platinum paste electrode and the zirconia electrolyte was estimated on the basis of a linear relationship between the peak area of linear sweep voltammetry and the actual contact area. The latter area was measured by microscopic observation of the contact area from one side of a transparent zirconia single‐crystal disk on the other side of which the platinum paste had been sintered. Applying the peak area vs. contact area relationship obtained to the same platinum electrode sintered on polycrystalline zirconia disks, the contact area was estimated from the voltammogram peak. The electrode performance increased monotonically with increasing contact area, but there was a small deviation from the proportional relationship. This deviation was corrected by using the length of the three‐phase boundary, instead of the contact area, as a morphological parameter.
2157
E. Lojou, M. Devaud, M. Troupel and J. Perichon
The electrocrystallization of cadmium, tin, or lead at a gold microelectrode has been studied in DMF solutions. For each deposited metal, the deposit grew through a 3D‐nucleation diffusion‐controlled process. The electroreduction of residual water on these deposits has been analyzed. The influence of the deposit structure on this phenomenom has been assessed.
2163
Olga P. Márquez, Jairo Márquez and Reynaldo Ortíz
Growth of a highly colored insoluble material on a platinum electrode by the oxidative reaction of 1,2‐dimethoxybenzene (veratrole) in acetonitrile is observed when tetrabutylammonium tetrafluoroborate is used as supporting electrolyte. The organic yield of the deposit reaches 98% when short‐timed electrolyses are performed. The main product has been characterized by several electrochemical and spectroscopic methods.
2167
James H. White and Anthony F. Sammells
This investigation explores direct methanol fuel cells incorporating perovskite anode electrocatalysts. Preliminary electrochemical performance was addressed following incorporation of electrocatalysts into polymer electrolyte (Nafion 417) fuel cells. Perovskite electrocatalysts demonstrating activity towards direct methanol oxidation during cyclic voltammetry measurements included, respectively,
,
,
,
,
,
,
, and
where
gave methanol oxidation currents up to 28 mA/cm2 at 0.45 V vs. SCE. Correlations were found between electrocatalyst solid‐state and thermodynamic parameters corresponding to, respectively, molecular electronic polarizability (α), the optical dielectric constant (∈), the perovskite spin‐only magnetic moment
, the number of d‐electrons in perovskite A and B lattice sites
, and the average metal‐oxygen binding energy for the perovskite lattice
, and corresponding fuel cell performance. This may have future merit for the prediction of new electrocatalyst family members for promoting direct methanol oxidation. Methanol diffusion from anode to cathode compartments appears to be a major obstacle to the development of polymer electrolyte methanol fuel cells.
2178
Trung V. Nguyen and Ralph E. White
Proper water and heat management are essential for obtaining high‐power‐density performance at high energy efficiency for proton‐exchange‐membrane fuel cells. A water and heat management model was developed and used to investigate the effectiveness of various humidification designs. The model accounts for water transport across the membrane by electro‐osmosis and diffusion, heat transfer from the solid phase to the gas phase and latent heat associated with water evaporation and condensation in the flow channels. Results from the model showed that at high current densities (> 1 A/ cm2) ohmic loss in the membrane accounts for a large fraction of the voltage loss in the cell and back diffusion of water from the cathode side of the membrane is insufficient to keep the membrane hydrated (i.e., conductive). Consequently, to minimize this ohmic loss the anode stream must be humidified, and when air is used instead of pure oxygen the cathode stream must also be humidified.
2187
Ibrahim H. Omar, H. J. Pauling and K. Jüttner
2192
G. S. Frankel, R. C. Newman, C. V. Jahnes and M. A. Russak
The pitting behavior of sputter‐deposited Al binary alloy thin films was studied. Pitting and repassivation potentials were determined in 0.1M
for samples in freshly deposited and air‐aged states. Aging for several years in laboratory air increased the pitting potential for some of the alloy systems but had no effect on others. The repassivation potentials, meaningful values for pits in thin films, were found to be very close to the pitting potentials of freshly‐deposited films for many alloy systems. Stable pits initiate in these Al binary alloys at potentials just above the value at which they would repassivate, indicating that pit growth considerations control the pitting process. By determining the pit anodic current density just before passivation it is shown that alloying improves pitting resistance through a reduction in the ability of pits to maintain the critical local environment necessary for growth. The influences of alloying on the passive film chemistry and on the tendency of the metal to repassivate (depassivation pH) are secondary in nature.
2197
R. H. Lamoreaux and Daniel Cubicciotti
Mixed potential modeling of the stainless steel corrosion potential (CP) in high temperature water has concentrated on aqueous species reactions at the steel/water interface and has ignored the variable stoichiometry oxide layer, which reacts with water to gain or lose oxygen. The oxide/water couple contributes to the CP during the slow approach to the steady state and to the determination of the steady‐state oxygen ratio at the water interface. The CP dependences of the steady‐state oxygen to metal ratios of the γ‐iron oxide and
phases have been analyzed by using estimated thermodynamic properties.
2205
F. Mansfeld and H. Xiao
2210
J. ‐E. Svensson and L. ‐G. Johansson
2217
Shigeru Umino and John Newman
The restricted diffusion method was used to measure the differential diffusion coefficient of sulfuric acid in water at 25°C for the concentration range from 0.3 to 7.5 molar. The concentration gradients of diffusing species were observed by Rayleigh interferometry. Experimental transport data are analyzed with concentrated solution theory of electrolytes in order to elucidate macroscopic transport characteristics of sulfuric acid in terms of specific binary interactions in solution. Results indicate that the transport properties of sulfuric acid are determined by the hydrogen ion‐water molecule interaction.
2221
Andre M. T. van der Putten and Jan Willem G. de Bakker
Electroless plating is used commercially for the simple and low cost deposition of metal coatings on relatively large area substrates. For plating of very fine metal patterns such as (submicron) contact holes in integrated circuit technology, anomalous behavior has been found with respect to the initiation and film growth. First, the areas to be metallized are so small that mass transport by nonlinear diffusion, which is considerably enhanced compared to linear diffusion to large area substrates, must be considered. A second effect that must be considered is electrical connections within the substrate. An ohmic connection of a small hole to a large substrate leads to plating potential pinning of this hole, i.e., the local potential at the contact hole during plating is determined by the steady‐state value that is established at the large area substrate. Dependent on the exact conditions, these two geometrical effects can lead to both an enhanced growth rate of the metal compared to bulk substrates, or to no metal deposition at all. The experimental observations can be explained by the mixed potential theory. This insight in turn indicates how uniform deposition rates in contact holes still can be achieved, regardless of their exact geometry.
2229
Andre M. T. van der Putten and Jan‐Willem G. de Bakker
Wet chemical processes such as etching or plating are generally isotropic. Although anisotropic wet etching can be achieved using single‐crystalline substrates or a duplex resist, anisotropic metal deposition seems a difficult task. However, we show here that anisotropic deposition of Ni has been accomplished in an acid electroless Ni bath to which an appropriate level of Pb2+ has been added. Since the edges of a given pattern experience an additional contribution from nonlinear diffusion, mass transport to these edges is enhanced compared to the bulk of a substrate. As a result the surface concentration of the adsorbed stabilizer is also higher at the edges. By choosing the proper Pb2+ concentration, the edges can be selectively poisoned: bevels can be grown with an angle that is a function of the stabilizer concentration in the electrolyte. That the Pb2+ stabilizer inhibits the cathodic partial reaction (metal deposition itself), but not the oxidation of the reducing agent has been verified with cyclic voltammetry at a rotating‐disk electrode, carried out in the vicinity of the plating potential. The process can be used to deposit metal pyramids onto the Al bond pads of an integrated circuit. This morphology is useful for the direct mounting of an integrated circuit onto a conductor pattern (flip chip).
2235
Sandra W. Watson
2238
Hiroya Yamashita, Takeshi Yamamura and Katsutoshi Yoshimoto
The relation between catalytic ability for hydrogen evolution reaction and characteristics of nickel‐tin alloys prepared by electroplating was investigated. The catalytic ability was found to strongly depend on preparation conditions. Hydrogen overvoltage was drastically decreased with an increase of the width at half height of x‐ray diffraction peaks which was related to the tin content. The nickel‐arsenide‐type structure and the initial high catalytic ability remained unchanged after an 800 day durability test, suggesting that the addition of the specific amount of tin, which itself had high overvoltage, enhanced the catalytic ability of nickel.
2244
K. Ohtani, T. Ohmi and K. Ihara
The adhesion and removal behavior of metallic impurities on a PFA sheet surface was examined with TRXRF analysis. Metals such as Fe and Cu are strongly adhered, and they can be removed to some extent by SPM or FPM cleaning. The surface metallic concentration of PFA sheets did not increase when they were dipped into UPW or chemicals contaminated with metals, therefore it is assumed that metallic impurities do not adhere to the PFA surface from liquids. Moreover the metallic transfer tests showed that a cleaned PFA sheet did not contaminate Si wafers but an uncleaned sheet polluted the wafer strongly with metallic impurities. Therefore, when PFA molded parts such as wafer carriers and tubes are used in wet processing in semiconductor manufacturing, they must be cleaned by SPM or FPM cleaning.
2250
Dawn M. Bernardi, Hiram Gu and Andrew Y. Schoene
A two‐dimensional mathematical model of the lead‐acid cell that details nonuniformities along cell height as well as thickness is presented. The model is an extension of earlier, one‐dimensional models that simulate variation across the cell thickness alone. The model results show significant variations of current density and other variables in cell height, even at relatively low rates of discharge. The local electrochemical reaction rates are lowest at the bottom center of the electrodes and highest at the top. As discharge proceeds, the distributions in reaction rates and current density become more uniform from the top to the bottom of the cell. Also, significant variations in sulfuric acid concentration throughout the cell develop during discharge. The most concentrated acid is located at the bottom center of the negative electrode, and the most dilute acid is located at the top center of the positive electrode. Predictions of cell voltage are nearly that of one‐dimensional model results for the conditions studied; however, variations across cell thickness by one‐dimensional models should be considered as an average of the behavior along cell height for all practical operating conditions.
2258
Ying Kang and Jacob Jorné
Morphological stability analysis for the photoelectrochemical etching of n‐type Si is performed, in which the stability of the back‐illuminated Si‐electrolyte interface is theoretically investigated. Both the transport of holes in the semiconductor and ions in the diffusion layer are considered, together with the electrochemical reaction and surface energy. The roles and the effects of the various parameters, such as applied potential, dopant concentration, current density, illumination intensity, surface energy, and electrolyte concentration, on the morphology of porous silicon are studied. The results show that porous silicon is formed when the dissolution process is controlled by the supply of holes in the semiconductor, and the density of porous silicon is a property which is both material‐ and process‐dependent.
2265
Shih‐Min Lin and Ten‐Chin Wen
A systematic modeling analysis of Ir‐Ru‐Sn ternary oxide‐coated electrodes fabricated by thermal decomposition is performed. Using mixture experimental design, empirical models are fitted and plotted as contour diagrams which facilitate comparisons with experimental trends noted by other investigators and reveal the synergistic/antagonistic effects between the mixed oxides. The results indicate that each component demonstrates different performances in either binary (Ir‐Ru, Ir‐Sn, and Ru‐Sn) or ternary (Ir‐Ru‐Sn) systems, with the Ir 75%‐Ru 25% binary electrode being by far the most valuable anodic candidate for oxygen evolution in acidic media. X‐ray photoelectron spectroscopy analysis shows that the Ir 75%‐Ru 25% binary electrode surface is enriched with Ir, while Auger electron spectroscopy depth profile results demonstrate inhomogeneous bulk.
2272
Michael Matlosz
Two‐step reaction mechanisms involving adsorbed monovalent intermediate ions for the electrodeposition of iron and nickel as single metals can be combined to form a predictive model for the codeposition of iron‐nickel alloys. Inhibition of the more noble nickel in the presence of iron is caused by preferential surface coverage of the adsorbed iron intermediate resulting from a difference between the two elements in Tafel constant for the electrosorption step. The role of hydrolyzed cations and surface pH is investigated and methods for evaluating the influence of pH are explored. The analysis shows that changes in surface pH with potential are not necessary for iron‐rich (anomalous) deposits, but that variations in pH from one electrolyte to another may influence deposit composition. The tendency toward iron‐rich deposits with increasing overpotential exists in all systems, however, and can be prevented only by decreasing the iron concentration of the bath. An extension of the analysis to account for transport limitations in baths with low iron concentration is developed and calculations with the model are presented to illustrate the effects of current density and electrolyte convection under conditions similar to those investigated experimentally in the literature.
2279
Ivan Krejčí, Petr Vanýsek and Antonín Trojánek
Transport of
ions through modified microporous polypropylene membranes (Celgard 3401, 3501) was studied using polarography and conductometry. Soluble Nafion as an ion exchange modifying agent was applied to the membrane by several techniques. The influence of Nafion and a surfactant on transport of zinc ions through the membrane was studied. A relationship between membrane impedance and the rate of
transport was found. The found correlation between conductivity, ion permeability, and Nafion coverage suggests a suitable technique of membrane preparation for obtaining the desired zinc ion barrier properties.
2283
Hiromi Tokoi
An improved sodium sulfur cell design is proposed to enhance capacity and to decrease internal resistance. The cell is constructed with the sodium negative electrode inside a β″‐alumina tube and an annular sulfur positive electrode that utilizes unique and separate charge and discharge electrodes, outside the tube. The active material in the positive electrode is circulated, using the density difference between sulfur and sodium pentasulfide. An experimental cell was stably charged and discharged in the two‐phase region composed of sulfur and sodium pentasulfide. Compared to a conventional cell design, the effective cell capacity was increased without increasing the surface area of a β″‐alumina tube while the internal resistance was decreased. The resistance decrease was due to a thinner positive electrode and the unique charge and discharge electrodes.
2287
R. L. Mahajan and X. A. Wang
This paper presents artificial neural networks (ANNs) to model thermally based microelectronic manufacturing processes. The specific processes chosen are the chemically vapor deposited (CVD) epitaxial deposition of silicon in a horizontal reactor and “pool boiling” as applied to vapor‐phase soldering. In the CVD processes, an analytic model is used to generate data under simulated production conditions. Part of the data sets are used to train the neural network models. These models, referred to hereafter as physiconeural models, are then used to predict the output as a function of input parameters for the other part of the data sets. For pool boiling, an empirical correlation is used to train the ANN model. A comparison of these predictions with the physical model's computational results for the CVD process, and the experimental data for the pool boiling shows good agreement. These results show the effectiveness of the artificial‐neural‐network technique for modeling complex processes. Further work is in progress to exploit fully the potential of neural models, singly or in conjunction with physical models for run‐to‐run and real‐time process control.
Solid‐State Science and Technology
2294
A. Deptula, M. Carewska, T. Olczak, W. Lada and F. Croce
Spherical powders (with diameters <100 μm) of zirconia‐ceria hydroxide gels (stabilized with nitrates or chlorides) were fabricated by a water extraction variant of the sol‐gel process. The resulting powders were calcined at 400, 600, and 800°C in order to obtain crystalline forms, subsequently pressed at various pressures, and then sintered for 8 h at 1700°C. The sintered pellets had relatively high geometric density (in some cases >95% of the theoretical density) and showed both tetragonal and/or cubic x‐ray phases. The bulk density values of these ceria‐doped zirconia sintered pellets are much higher than those obtained for the
‐ or
zirconia samples prepared by the same process.
2297
Fumiyoshi Kirino, Akiko Mutou, Fumiko Yano and Norio Ohta
The wet corrosion mechanism on
magneto‐optical recording film was analyzed by Auger electron spectroscopy (AES) and electron spectroscopy for chemical analysis (ESCA). The corrosion reaction rate of the film is slower as the Nb concentration is higher. From AES measurement, Tb is oxidized on the surface of the
film; however, the oxide layer thickness is thinner with increasing Nb concentration. From ESCA measurement, Fe and Co are in the metallic state, and Nb is oxidized after exposure to 80°C at 95% RH for 100 h. These results show that when Nb oxide exists, the decrease in wet corrosion rate is effective for protection.
2302
Anita Sharma and Philip D. Pacey
A sensor employing yttria‐stabilized zirconia as an electrolyte and platinum paste as electrodes was exposed to rapid changes in oxygen pressure. The response time of the sensor was studied as a function of initial and final pressures between 5 and 760 Torr and temperatures between 773 and 948 K. Experiments in which the oxygen pressure suddenly increased had faster response and the opposite dependence of response on initial pressure when compared to experiments in which the pressure suddenly decreased. The order of the process with respect to final oxygen pressure was close to −0.25 at the lower temperatures, declining slightly at higher temperatures. The activation energy was
and the logarithm of the pre‐exponential factor was
. The differential rate laws for various possible elementary steps have been integrated and the resulting expressions have been fit to experimental curves of voltage as a function of time. The results at lower temperatures are in agreement with a model in which response is limited by the rate of conversion of electron holes and singly charged oxygen anions to neutral oxygen atoms at the surface of the zirconia.
2309
K. Fujino, Y. Egashira, Y. Shimogaki and H. Komiyama
A simulation model for atmospheric pressure (AP) CVD has been developed using one‐dimensional diffusion and mass conservation equations. The model was applied to trench step‐coverage of the tetraethoxysilane (TEOS) and
CVD, in which it was not necessary to consider lateral diffusion because of narrow (and deep) trenches. For nondoped silicate glass (NSG), the step‐coverage of a 4.5 aspect ratio trench showed a good fit if a sticking probability of 0.0039 was assumed for the 0.6% ozone (in oxygen) deposition and of 0.0026 for the 6% ozone deposition (both 400°C). The reaction rate constant was compared with the diffusion mass‐transfer coefficient, and the reaction proved to be limited by diffusion of the reactant, TEOS, which directly participated in the CVD reaction. For the 2 m/o phosphosilicate glass (PSG) step‐coverage, which had a slight overhang, the model matched the obtained results well only when an active growth species with a high sticking probability of 1.0 was added to the growth species of nondoped oxide. This analytical simulation method satisfactorily explains the experimental data.
2313
G. Galvagno, A. Scandurra, V. Raineri, C. Spinella, A. Torrisi, A. La Ferla, V. Sciascia and E. Rimini
Al‐based precipitate evolution for 80 keV Al ions implanted in Si has been investigated. Precipitates are formed during high temperature annealings of
implanted samples. They are located at two depths where Al concentration peaks are detected. Al atoms are gettered into the extended defects present in the crystal and/or precipitate when their concentration is higher than the solid solubility value at the annealing temperature. Increasing annealing time, precipitates dissolve out and only a small fraction of atoms diffuses into the sample, meanwhile the greater part evaporates from the sample. At
dose the Al concentration is below the solid solubility limit. The secondary defects are not detected and the dopant profile does not display anomalous peaks. Moreover, all the implanted Al is electrically active and remains in the sample during the first instant of annealing. At higher annealing times it diffuses out of the sample reducing the residual dose.
2319
Hikmet Kasapbasioglu, Peter J. Hesketh and Albert T. Macrander
Silicon x‐ray analyzer crystals were microfabricated by dicing and etching 10.3 cm (4‐inch) diam, 1.35 mm thick, undoped float zone (111) silicon wafers. These analyzer crystals are intended for a beam line at the Advanced Photon Source synchrotron accelerator ring under construction at the Argonne National Laboratory. Parallel and perpendicular, 1 mm spaced grooves were cut on the silicon wafers using an automated dicing saw. The grooves were cut at 15° and 105° to the ‘110’ primary flat to avoid crystallographic cleavage directions because mechanical strength was desired. The depth of the grooves was 1.15 mm, which was 85% of the wafer thickness. The two cutting parameters, progressive cutting thickness, and feed rate were optimized to reduce saw damage and chipping. Saw damage, which extended over a region of about 30 μm from grooves was removed by isotropic etching. The quality of the single crystal was tested by measuring the width of x‐ray rocking curves with a double‐crystal diffractometer. The best width obtained with 11.2 arc‐s. Since the ideal full width at half maximum (FWHM) according to x‐ray dynamical diffraction theory is 9.7 arc‐s, a broadening function with a FWHM of only 5.6 arc‐s is present due to residual strains (quadrature addition is assumed).
2323
E. Klausmann, W. R. Fahrner, S. Löffler and H. C. Neitzert
The admittance of metal oxide semiconductor (MOS) diode after switching from inversion to deep depletion is calculated. Special attention is given to the final stationary state in inversion conditions. For this state the relaxation equations must be modified because the usually assumed large signal carrier deficits are not valid. The results of these dispersion measurements are compared with the conventional Zerbst technique. Good agreement is obtained. The dispersion technique is a valuable tool for determining very short lifetimes.
2328
L. A. Lipkin
A technique for monitoring oxidation furnaces using a surface charge analyzer (SCA) is investigated. This tool produces excellent results when compared with the conventional capacitance‐voltage (CV) techniques. SCA is more precise, significantly faster and easier, and more accurate than the traditional CV technique. The SCA agrees with the CV measurements for 90% of the measurements, but is more reliable for identifying true oxide quality fails. The instances where the two techniques did not agree were due almost exclusively to measurement errors with the CV technique. SCA monitoring of oxidation furnaces easily can replace the day‐to‐day monitoring now performed with the CV technique, and the tool would pay for itself in labor alone in less than two years. Considering all these issues, the SCA is an attractive option for oxidation furnace monitoring.
2332
G. A. Mattiussi, P. J. Scanlon and I. M. Templeton
Negative‐ and positive‐tone e‐beam resists have been exposed by focused beams of Si++ and Be++ ions. The resolution of the negative resist, Shipley SAL601‐ER7, was better than 0.2 μm and vertical sidewalls were achieved. A dose of
was required to retain the full thickness of the resist after developing. Different postexposure bake (PEB) times and temperatures were examined in this work. A saturation in resist response was observed at moderately high PEB temperatures (115–125°C). This effect has not been reported previously for either ion‐beam or e‐beam exposure. Increases in developing time can increase the sensitivity and the effective contrast of this resist. The positive‐tone resist, OCG Microelectronic Materials P28, is at least two to three times more sensitive than PMMA. It also displays a wide range of doses
for which positive‐tone imaging is possible. Present results show the resolution of P28 to be at least 0.3 μm, which is not as fine as that of polymethylmethacrylate (PMMA). Preliminary results on the behavior of the P28 resist as a mask for silicon etching are presented.
2339
David J. Monk, David S. Soane and Roger T. Howe
2346
M. Murata, K. Yamauchi, H. Kojima, A. Yokoyama, T. Inoue and T. Iwamori
2356
J. Nagel, M. Reiche, S. Hopfe and D. Katzer
During polybuffered local oxidation of silicon processing the formation of pits in the polysilicon buffer layer is often observed after wet nitride etch. While nitridation of whole polysilicon grains due to a chemical reaction of ammonia, water, and silicon is discussed in the literature, it is shown in this work that the pits originate from voids in the polysilicon film which are already created during oxidation. For the first time, a stress‐induced migration effect in polysilicon, analogous to void formation in narrow aluminum interconnect lines, is proposed as the primary cause of the pit problem. Based on the experimental findings a process strategy is suggested to avoid substrate damage in the active transistor area.
2360
Bea Cao, Juan Carrejo and N. David Theodore
Grain‐size measurement in thin metal films is important for many applications. Typically, techniques which examine the film surface topography, such as scanning electron microscopy (SEM) and scanning tunneling microscopy/atomic force microscopy (STM/AFM), are used for grain‐size measurement. We have studied the extent of correlation between the surface topography and microstructure in thin aluminum films containing 1.5 weight percent copper using a scanning electron microscope equipped with a heating stage and plan‐view transmission electron microscopy (TEM). Surface grooves were found on the film surface which bore no correlation to grain boundaries, suggesting that grain size measurement by SEM and AFM could produce erroneous results due to interference from surface topography. Additional information from another technique, such as TEM, is recommended for verification.
2363
C. Y. Mak, S. Nakahara, Y. Okinaka, H. S. Trop and J. A. Taylor
An investigation was conducted to examine the low temperature (<300°C) annealing behavior of two types of fine‐grained electroless copper deposits. Heat‐treatment from continuous oven‐annealing was compared to that from thermal cycling in a fluidized sandbath (FSB) unit. It was found that one of the deposits, referred to as type IV electroless copper, showed considerable resistance to recrystallization. Microscopic and chemical analyses indicated that this electroless copper contained a high density of organic inclusions which were effective in pinning grain boundary movement and preventing recrystallization. Type IV electroless copper also had high gaseous hydrogen content. The FSB experiments showed that this entrapped hydrogen could induce a local plastic deformation mechanism and cause internal fatiguing in the copper during thermal cycling. The other deposit, referred to as type I electroless copper, was relatively free of foreign incorporation. This copper recrystallized readily upon annealing. The driving force for grain growth was the surface energy released from elimination of grain boundaries.
2370
Gyoichi Nogami, Hirohumi Maruyama and Kazutaka Hongo
A new type of ion sensor was developed. Thin film perovskite materials such as
were deposited onto a metal electrode by a hydrothermal‐electrochemical method in an autoclave. The resultant electrode was paired with a counter‐electrode and immersed in solution. When an external step bias was applied, transient current was observed even in pure water, the electric conductivity of which was extremely small. The initial current was precisely proportional to the ionic concentration of the solution. The detection limit of the sensor depends on the purity of the solvent. When extra‐pure water is used, the detection limit is about 10−7M. This sensor can be also used as biosensor.
2373
A. C. Rastogi, K. S. Balakrishnan and Archana Garg
2376
Andre M. T. van der Putten
2378
Toshihiro Yamase and Kyota Uheda
electroluminescence (EL) cells have been fabricated with the
layer with 40–80 μm thickness, as the emissive medium. The spectral distribution of EL, induced by the applied negative voltage pulse, indicates the presence of three emission envelopes of nitrogen plasma, oxygen‐to‐tungsten (O → W) ligand‐to‐metal charge transfer (LMCT) emission, and Eu3+ f‐f emission for every dispersion layer of Ca2+, Sr2+, or Ba2+ salt of
and
pellet. The Eu3+ EL lines are similar to Eu3+ photoluminescence lines but with relatively higher intensity in the
transition. Typical operating conditions are
at 100–300 Hz. A high porosity of the
layer which allows a voltage drop to occur in the layer, resulted in a significant contribution of the nitrogen plasma to the total emission. Comparison of transient behaviors among three emissions exhibits an accumulation of charges inside the
layer which induces an internal field. Such charges once trapped are released and accelerated by external field or by internal field after the applied pulse is turned off, until enough kinetic energy is acquired to excite
. The insulating Mylar film is important for the EL in that it allows accumulation charges to remain inside the
layer. The EL intensity is still very low, due to the small number of internal carriers and the small amount of carrier accumulation in the vicinity of the
.
2384
Zhengming Zhang and John H. Kennedy
Melt‐quenched compounds with
ratios from 0.5 to 0.67 form homogeneous glasses, while the 0.33 and 0.4 compositions show two amorphous phases. The 0.33 and 0.4 melt‐quenched compounds were identified as glasses by x‐ray diffraction, which was supported by differential scanning calorimetry and electric measurements. However, solid‐state magic angle spinning‐nuclear magnetic resonance at high speed (≥ 8 kHz) revealed the existence of short‐range ordered units in the 0.33 and 0.4 melt‐quenched compounds. The electric conductivities, obtained by complex impedance analyses, of the melt‐quenched compounds in the Ag‐P‐S system were studied along with glass transition temperature,
, values and compared with Li+ conductive sulfide glasses. Eight crystalline compounds were synthesized and studied in the Ag‐P‐S ternary system:
,
,
,
,
,
,
, and
. The ionic conductivity and electronic conductivity of the ordered Ag‐P‐S system were investigated by complex impedance analyses and dc Wagner measurements. The
crystalline compound showed the highest room temperature conductivity,
, in the Ag‐P‐S system with a value of
. The electronic conductivity of the
crystalline compound was <10−10 S/cm at room temperature. It appears that the
tetrahedron provides a pathway conducive to high ionic conductivity with a low activation energy.
2390
N. K. Chen and C. Lee
2395
T. J. Dalton, J. C. Arnold, H. H. Sawin, S. Swan and D. Corliss
The formation of microtrenches in polysilicon plasma etching over thin gate oxides has been observed and modeled Microtrenches are small trenches formed in the bottom of etching features and are caused by the localized breakthrough of the gate oxide and subsequent rapid etching of the underlying silicon. In contrast to previous reports, the microtrenches were observed a small distance away from the sidewall. Their formation and position were functions of the thickness and angle of the photoresist and polysilicon sidewalls. Simulation of ion scattering from the sidewalls of the etching features indicated that the flux of ions at the bottom of the feature was peaked away from the sidewall under the process conditions of this study. The position of the peak ion flux predicted by the model and the experimentally observed trench varied in a similar fashion as a function of the topography of the etched feature.
2402
Masahiro Hagio
2406
A. Giani, F. Pascal‐Delannoy, G. Bougnot, G. G. Allogho and J. Bougnot
2410
Tetsuya Homma, Takuya Katoh, Yoshiaki Yamada and Yukinobu Murao
2414
T. Nishida and T. Tamamura
The microloading effect in the anisotropic wet etching of
is quantitatively studied for distributed feedback‐LD grating fabrication. In this study, 240 nm pitch gratings based on resist patterns with various space widths defined by E‐beam lithography were etched in saturated bromine water (SBW) and hydrobromic acid
. The etched depth and the shape show a clear dependence on the space width, and this microloading effect can be explained by the diffusion of the reactant, the length of which is comparable to the grating size. Dry‐etching is found to reduce the loading effect. The wet etching model and controllability of the coupling coefficient for DFB‐LD gratings are discussed.
2422
G. Salviati, C. Ferrari, L. Lazzarini, L. Nasi, C. E. Norman, M. R. Bruni, M. G. Simeone and F. Martelli
Strain‐induced dislocations have been studied in low and medium mismatched (001) oriented
superlattice heterostructures. Their optical quality, composition, residual strain, dislocation nature, and location have been studied by x‐ray diffraction and electron microscopy techniques. Different predictions of the residual strain have been discussed briefly. All the samples presented perpendicular networks of misfit dislocations with different densities along the [110] and [110] directions. The dislocations were confined inside the buffer layer or at the buffer‐superlattice interface without threading the superlattice. Asymmetric dislocation movement along the ‘110’ type directions were induced by the electron beam in a scanning electron microscope. Panchromatic cathodoluminescence observations allowed the on‐line observation of the dislocation movement when thickness and composition were such that a low linear dislocation density
was present. The effect was correlated to the different level of metastability of the superlattice. Almost only 60° type misfit dislocations were observed in all the specimens.
2427
Y. Shacham‐Diamand, A. Dedhia, D. Hoffstetter and W. G. Oldham
The transport of copper in silicon dioxide thermally grown on single crystalline silicon was studied by capacitance techniques, secondary ion mass spectroscopy (SIMS) analysis, and Rutherford backscattering spectrometry (RBS). Metal/oxide/silicon (MOS) capacitors were used to study the penetration of copper into the oxide as a function of temperature and applied electric field. The role of a titanium layer between the copper and the oxide was also studied. Bias‐thermal stress (BTS) studies of MOS structures were conducted at 150°C to 300°C with an electric field of 1 MV/cm for times ranging between 10 min and 168 h. It is shown that without bias a relatively small amount of copper reaches the silicon/silicon dioxide interface, with a maximum surface concentration of about 1017 cm−3 that drops exponentially with depth in the oxide. The high‐frequency (100 kHz) capacitance vs. voltage (CV) characteristics of the MOS devices changed drastically when a positive bias was applied to the gate and copper reached the silicon/silicon‐dioxide interface. The penetration time for copper through the oxide was characterized as a function of the temperature. The copper drift velocity, mobility and diffusivity in the oxide were determined and the copper profiles in the capacitors were characterized by SIMS. The activation energy for the diffusivity and mobility models was found to be
. Devices without a barrier layer, which were stressed under a positive electric field, showed high copper concentration in the oxide, up to 1021 cm−3. At high temperatures and long stress times a significant amount of copper was also found in the silicon substrate. A titanium layer thicker than 5 nm acted as effective barrier even after 30 h of BTS at 300°C.
2432
N. Tomesakai, M. Suzuki and J. Komeno
A metallorganic vapor phase epitaxial (MOVPE) technique is used to produce successfully the epitaxial layer of a selectively doped
high electron mobility transistor (HEMT) structure. We have developed a method for mass producing HEMT‐LSIs (large‐scale integration). Our low pressure barrel reactor can grow twelve 3‐inch wafers simultaneously using a wafer rotation system. The
heterointerface fluctuates by less than several angstroms over the entire wafer. Their electrical characteristics are excellent and the distribution in both layer thickness and donor concentration satisfy the demands for LSI applications. We used photolithography to fabricate HEMT devices with 0.6 μm long gates. We applied the MOVPE technique to a 64 kbit HEMT SRAM and obtained a typical address access time of 1.2 ns at a power dissipation of 5.9 W.
ERRATA
2293
G. C. Schwartz, Y. ‐S. Huang and W. J. Patrick
2293a
T. Takebe, T. Yamamoto, M. Fujii and K. Kobayashi