ELECTROCHEMICAL SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
1261
Bradley R. Karas
An alternating current (ac) resistance technique for sodium‐sulfur cells is described. The method has been applied to central sodium and central sulfur cells with between 16 and 650 Ah capacity. The shape of the ac charge resistance‐capacity plot has been correlated with resistive layer composition. Anomalies in direct current (dc) resistances for oriented‐mat sulfur electrode cells are explainable in conjunction with ac analysis. The increased sensitivity of ac compared to dc measurements has been utilized to identify incipient electrolyte failure and sodium electrode problems not discernable by the latter technique.
1266
Bradley R. Karas and Randall N. King
The effects of current density (54–865 mA/cm2), temperature (330°–355°C), and discharge depth (
to
) on sodium‐sulfur cell efficiency, resistance, capacity, and longevity are presented. Equal discharge and charge cycle times obtained on 16 Ah laboratory cells at 865 mA/cm2 and 335°C demonstrated the resistive layer effectiveness in preventing sulfur passivation of the beta″‐alumina electrolyte surface during cell charging. Elevated temperatures increased cell efficiency ∼3%/10°C, decreased resistance, and increased capacity. A group of cells operating at 216 mA/cm2, twice the standard current density, and 330°C have obtained ∼700 cycles, ∼900 Ah/cm2, with little performance deterioration. The cells are ∼82% efficient and display ∼80% of theoretical capacity. Alternating current resistance analysis of typical laboratory cells revealed an increase in discharge resistance occurred when cells were cycled between
and
. Correlations with the sodium‐sulfur phase diagram indicate the resistance rise was due to precipitation of
. Upon subsequent charge inception, the ac resistance dropped. However, an increased two‐phase charge resistance was recorded. This suggested that
deposition occurred at the resistive‐mat/conductive‐mat interface.
1273
The following article is Free article
Emad Roayaie and Jacob Jorné
A mathematical model which includes mass transfer within the pores has been applied to the flow‐through porous graphite electrode during the discharge of the zinc‐chloride battery. The purpose of the model is to obtain key design parameters such as potential distribution, concentration distribution of dissolved chlorine and zinc chloride, and local reaction rate distribution within the porous electrode. The resultant coupled nonlinear differential equations have been solved numerically for the galvanostatic operation. Potential, concentration, and reaction‐rate distributions have been obtained for various operating conditions such as specific area of the porous electrode (100–1000 cm−1), electrolyte flow velocity (0.5–3.0 cm/min), discharge current density (30–100 mA/cm2), electrode thickness (0.2–0.4 cm), and direction of flow. The results can be used in the optimization of the energy efficiency of the zinc‐chloride battery.
1277
Denise M. Aylor and Patrick J. Moran
1281
Blanca M. Rosales and S. L. Granese
By means of electrochemical techniques, the corrosion of Zn in
aerated and deaerated aqueous solutions at 25°C was studied. The kinetic equations proposed from values obtained in the Tafel region were in good agreement with those provided by computer program POLCURR (1) developed by Gerchakov et al. for overpotentials of ±20 mV. On those bases and analyzing by x‐ray, the corrosion products formed an overall reaction was proposed which would be controlled by an adsorption‐oxidation step.
1284
O. Teschke, F. Galembeck and M. A. Tenan
Mechanical oscillations of the solution meniscus risen around a corroding wire electrode were observed in synchronism with electrical current oscillations. Scanning electron microscopy coupled to microprobe analysis was used to investigate the topochemistry of the system under study. Solution capillarity effects on iron and on iron compounds are related to the oscillations detected in this system.
1288
Hugh S. Isaacs and Yuichi Ishikawa
The currents flowing from a localized corrosion site (LCS) on passive stainless steel in air‐saturated
have been studied using a vibrating probe electrode. The potential behavior during applied currents was analyzed by assigning equivalent circuits to the passive surface and the localized site so that the paths of the current across the passive surface and the LCS could be calculated and compared with the measured values. The equivalent circuit of the passive surface without active localized corrosion was determined from potential transients and was found to be dependent on the prior history of the electrode. The LCS was equated to a resistance with an EMF which were calculated from the LSC current and specimen potential. The variations of this resistance were attributable to changes in solution resistance adjacent to the LCS. It was found that the capacitance of the passive surface played a major role during potential transients and the initiation of pitting.
1293
Krishan L. Luthra
1298
Mark W. Verbrugge and Charles W. Tobias
A mathematical model is presented for the electrodeposition of multicomponent alloys by an arbitrarily specified current source. The model takes into consideration transient, convective mass transfer to a rotating disk electrode, Butler‐Volmer kinetics, and individual component activities in the electrodeposit. The model can be used to calculate current‐potential relationships, ionic concentration profiles, and electrodeposit composition. Results for square‐pulse, pulse‐reversal, and triangular current waveforms are presented. An analogous model for potential‐controlled electrolysis is also discussed.
1307
R. C. Paciej, G. L. Cahen Jr., G. E. Stoner and E. Gileadi
The recovery of gallium from dilute solutions is known to be slow and inefficient due to competing hydrogen evolution and the limitations of mass transport. Methods used to improve the process include pulse plating, inhibition of hydrogen evolution by suitable additives, increasing the pH, and conducting the process at temperatures above the melting point of gallium. In the present work, an alternative approach was taken employing microelectrodes to enhance the rate of mass transport and thus to increase the rate of gallium recovery. Potentiostatic plating and stripping experiments were performed using electrodes ranging in diameter from 1 cm down to 45 μm. The effect of electrode diameter on the rate and efficiency of the plating of gallium was studied at different potentials and under different conditions of mass transport. The effect of plating time was also determined, and the conditions for the optimum recovery of gallium in terms of the overall rate as well as the current efficiency were evaluated. Carbon fiber epoxy composites can serve as ensembles of microelectrodes. It was shown that, with a typical radius of 3–5 μm for the individual fibers, considerable enhancement of the rate of recovery of metals from dilute solutions can be expected.
1312
J. D. Luttmer and Isaac Trachtenberg
1315
Ronald L. Cook, Patrick F. Dempsey and Anthony F. Sammells
1319
J. C. W. Folmer, John A. Turner, R. Noufi and David Cohen
1328
Tetsuo Sakai, Hiroyasu Takenaka, Noboru Wakabayashi, Yoji Kawami and Eiichi Torikai
Gas permeation properties for Nafion membranes and their composites were investigated under various conditions. The permeability coefficients of Nafion depended greatly on the water content, the cation form, and the ion‐exchange capacity. The gas permeation rate through a same sample varied with temperature, pressure, and membrane thickness. The permeabilty of hydrogen was about twice as great as that of oxygen. The electrocatalyst plated on the membrane did not serve as a barrier for gas permeation, but the structure of the catalyst layer played an important role in gas permeation during water electrolysis.
1333
M. Gauthier, D. Fauteux, G. Vassort, A. Bélanger, M. Duval, P. Ricoux, J. ‐M. Chabagno, D. Muller, P. Rigaud, M. B. Armand et al
The feasibility of polyether‐based all‐solid‐state cells has been assessed in a joint research and development program. At 80°–100°C, cells using
or
positive‐electrode material and excess lithium show high material utilization at 0.5–1.0 mA/cm2 and can be cycled more than 250 times. Furthermore, a new family of polyether electrolytes has been found that allows room temperature (26°C) operation at 3–20 μA/cm2.
1340
Chy Hyung Kim, Bingyi Qiu and Ephraim Banks
Samples based on the
structure
were prepared. A combination of phosphorus substitution and reduction of M3+ content permitted increasing sodium content, the maximum sodium content being 3.3. Conductivity of this sample, measured by pulse and two‐terminal ac methods, was about
at 320°C, compared to
for
at the same temperature. Activation energies were slightly lowered with increasing sodium content, from 15 to 14 kcal/mol. In compositions with other rare earths, conductivity increased with increasing ionic radius of the rare earth ion. Lithium ions were introduced by ion exchange in molten
. The conductivities were slightly lower than those of the corresponding sodium samples, but decreased with increasing rare earth radius.
1345
Pal Joo and James Q. Chambers
1350
P. E. Richardson and C. S. O'Dell
Electrochemical, interfacial capacitance, and surface photovoltage (SPV) measurements have been used in a study of oxygen reduction and xanthate chemisorption on in situ cleaved natural and synthetic lead sulfide crystals. Electrodes cleaved in nitrogen‐sparged 0.1M sodium tetraborate assume the flatband potential,
, at the instant of cleavage, and thus the cleavage potential decreases with increasing bulk electron concentration. Highly n‐type electrodes have a cleavage potential
of ≃−0.6V (SCE), and highly p‐type electrodes have a value of ≃−0.2V (SCE). The space charge is readily varied by applied potentials in the range −0.2 to −0.6V. This Bureau of Mines, U.S. Department of the Interior, report discusses the effect of the variable space‐charge layer on oxygen reduction and xanthate chemisorption.
1356
S. Waaben, I. Moskowitz, J. Federico and C. K. Dyer
Circuit analogs for a single battery cell have previously been composed of resistors, capacitors, and inductors. This work introduces a nonlinear circuit model for cell behavior. The circuit is configured around the PIN junction diode, whose charge‐storage behavior has features similar to those of electrochemical cells. A user‐friendly integrated circuit simulation computer program has reproduced a variety of complex cell responses including electrical isolation effects causing capacity loss, as well as potentiodynamic peaks and discharge phenomena hitherto thought to be thermodynamic in origin. However, in this work, they are shown to be simply due to spatial distribution of stored charge within a practical electrode.
1363
T. Biegler and M. D. Horne
Linear sweep voltammetry with a freshly renewed surface of a chalcopyrite
mineral electrode shows a small anodic prewave in acid electrolytes. The main anodic reaction, with complete dissolution of copper and iron, occurs at more positive potentials. Experiments under nitrogen show that the prewave is not a consequence of atmospheric oxidation during surface preparation. The prewave represents a surface oxidation of chalcopyrite to form a thin passivating film. The charge passed in forming this film is around 2 mC cm−2 for a polished surface. The prewave reaction is identified with the initial phase of the oxidative dissolution or leaching of chalcopyrite. Contrary to the reported behavior at 80°C, the surface film is stable at 25°C for long periods at open circuit. Various evidence, including the relative charges passed in forming and then reducing the surface film, and the presence of dissolved copper, leads to the following suggested stoichiometry for the prewave reaction

The product layer containing
and S is about 3 nm thick.
1369
Alfred Viehbeck and David W. DeBerry
1375
Chester J. Dymek Jr. and Lowell A. King
TECHNICAL NOTES
1380
Takao Nagatomo, Hidehiko Kakehata, Chiaki Ichikawa and Osamu Omoto
1382
Vernon D. Neff
1384
K. Shimizu and K. Kobayashi
1385
Gholamabbas Nazri and Rolf H. Muller
1387
D. Brynn Hibbert and Foo Y. Y. Yon‐Hin
SOLID-STATE SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
1390
M. Suzuki, Y. Ohnishi and A. Furuta
1394
Charles B. Greenberg
Methods for forming thin, transition metal oxide films pyrolytically from liquid spray vehicle are well known. On the one hand, there are the uniform and finely crystallized spinel‐structured films grown from organic solutions of acetylacetonates; one of these is herein reviewed. A spectrally similar film grown from aqueous solution, of another spinel composition (1), is not so well formed. This film's relatively gross morphology is a clue to its growth mechanism. The morphology can be explained qualitatively by invoking a model for closely associated phenomena characteristic of spray drying (2). By this model, solid or partially molten metal‐organic material approaches the hot substrate in the form of roughly spherical, porous, hollow shells. These remain after solvent evaporation from the droplets of the liquid spray. The hollow shells vaporize on the approach to the substrate, and the film grows by a CVD reaction at the substrate. Constituents which do not readily vaporize, such as impurities, impact the substrate and imprint a morphological pattern of collapsed shells. These comprise the rare clue for the analysis and for modeling film growth.
1398
D. Bélanger, J. P. Dodelet, B. A. Lombos and J. I. Dickson
1406
Tiao‐Yuan Huang, Donald J. Coleman and James L. Paterson
An LPCVD oxide/LPCVD nitride stack has been investigated as a possible substitute for the interpoly oxide in double‐level‐polysilicon VLSI processes. Results from capacitor lots show that 25 nm LPCVD oxide/25 nm LPCVD nitride stacks yield breakdown voltages greater than 25V with a tight distribution. The breakdown voltage can further be enhanced by depositing an additional LPCVD blocking oxide of 50Å thickness on the stack. Suitable thermal sealing oxides are also shown to be effective in enhancing the breakdown field strength. A further scaling of the stack thickness is also demonstrated.
1409
Dan Anderson and Kjell O. Jeppson
At high concentrations, impurity diffusion in semiconductors is governed by nonlinear diffusion processes. Using similarity analysis, a general expression for evaluation of the diffusion coefficient from experimental impurity profiles is derived for the case of redistributive diffusion of implanted impurities. This expression corresponds to the Boltzmann‐Matano analysis for the case of diffusion with constant surface concentration.
1412
Wen Lin and M. Stavola
In this paper, the origins of the microscopic impurity inhomogeneity in Czochralski (CZ) silicon are reviewed. The relevance of impurity segregation behavior and microscopic growth rate variations to the impurity microfluctuations are analyzed and discussed. The nature of the oxygen microfluctuations is studied in terms of its segregation behavior and its effects on precipitation. Spatially resolved infrared absorption and spreading resistance are used to study the oxygen microfluctuations induced by the melt thermal asymmetry, isolated by a manually controlled crystal growth. It is shown that oxygen segregates microscopically in the same manner as arsenic in silicon, that is,
for oxygen. A quantitative analysis yields a
value in the neighborhood of 0.3 for oxygen, which agrees well with the previous result based on a macroscopic analysis. Heat‐treatment experiments have shown that when CZ silicon exhibits microfluctuations in oxygen concentration the precipitation is not uniform; rather, the precipitation is enhanced in the high oxygen regions of the fluctuations. Such behavior can impede the formation of the denuded zone where the high oxygen regions meet the wafer surface, resulting in nonuniform denuded zone width across the wafer.
1417
P. A. Folkes, C. C. Chang and E. Lane
1424
Kazuo Nakajima and Jiro Okazaki
1432
R. Huq and G. C. Farrington
1437
A. Auerbach
We describe a novel method for generating fine metal lines with a laser. The laser radiation is focused onto the surface of a nonconductive silver nitrate‐doped polymer film to reduce silver. By translating the surface relative to the laser beam, a highly conductive silver line is formed. The measured resistance agrees well with the computed value for a silver conductor of comparable dimensions.
1441
G. S. Oehrlein, R. M. Tromp, J. C. Tsang, Y. H. Lee and E. J. Petrillo
Silicon surfaces which had been exposed to
reactive ion etching have been characterized by x‐ray photoelectron emission spectroscopy, He ion channeling, H profiling, and Raman scattering techniques. Plasma exposure of a clean Si surface leads to the deposition of a thin (∼30–50Å thick) C,F containing film. The near‐surface region (∼30–50Å) of the Si substrate is heavily disordered (“amorphized”), as found by ion channeling and Raman scattering. A modified, less damaged Si region extends from about 30–50Å from the surface to a depth in excess of 250Å. This layer contains a high concentration (∼5 atom percent) of H as shown by hydrogen profiling techniques. From the observation of Si‐H and
vibrational modes by Raman scattering, it has been shown that the H is bonded to the Si lattice. In ion scattering, the extended modified Si layer appears to cause a strongly enhanced background in the energy spectra. Results of Monte Carlo range calculations are reported and compared with the damage depth found experimentally.
1448
S. Aptekar, M. Fernandes and D. L. Kwong
An oxidation rate law for thin oxides, as suggested by Hu (2, 3), has been found to correlate very well with experimental data. The growth law, although not based on any interface reaction mechanism, has been formulated to be consistent with the observed power‐law pressure dependence of the linear rate constant through the use of a dummy parameter,
. The higher oxidation rate observed at thin oxides has been taken into account by an exponentially decaying term. The analysis assumes that
varies linearly over the thickness of the oxide. Values of the other parameters in the rate law have been taken from available data.
1450
M. Wittmer, F. Le Goues and H. ‐C. W. Huang
1456
M. Tanielian, R. Lajos, S. Blackstone and D. Pramanik
We have investigated the silicide‐silicon interface during the oxidation of titanium silicide on polysilicon. We find that during oxidation the polysilicon layer under the silicide is consumed inhomogeneously and that at the same time the titanium silicide moves into the polysilicon layer. Oxidations were carried out both in wet and dry
with similar results. This nonuniform consumption of the polysilicon layer appears to be related to the condition of the silicide‐silicon interface prior to the oxidation step. This effect can result in the reduction of the dielectric breakdown strength of underlying gate oxide in titanium silicide/polysilicon/oxide/Si structures.
1460
Shin‐ichiro Kimura, Eiichi Murakami, Kiyoshi Miyake, Terunori Warabisako, Hideo Sunami and Takashi Tokuyama
Silicon dioxide growth in an oxygen plasma is investigated using newly developed microwave discharge equipment with electron cyclotron resonance. It is found that the plasma oxidation kinetics can be explained by the Cabrera‐Mott model, in which the drift motion of ions is assumed, rather than by the Deal‐Grove thermal oxidation model. The drift motion of oxygen ions across the oxide film under the influence of self‐bias in the plasma is considered to be the plasma oxidation mechanism. Infrared absorption and etch‐rate measurements reveal that the physical properties of plasma oxidized
at 600°C are structurally quite comparable to those of thermally oxidized
.
1466
Yoshio Homma and Sukeyoshi Tsunekawa
Planarization of multilevel interconnection is most effective for achieving a higher packing density. However, it is shown by computer simulation that degradation of metallization step coverage becomes serious as the via aspect ratio increases. Conventional deposition methods, in which emitted particles flow onto the substrate and usually do not migrate, are shown to be inadequate for maintaining sufficient step coverage. A new deposition technique, RF/dc sputtering with RF bias for metal, is developed and found to provide sufficient step coverage and, moreover, planarity. In an application of the technique to aluminum film deposition, the existence of a resputtering effect was confirmed. Aluminum particles were found to deposit primarily near the bottom of the depressions and to fill up the depressions completely, through sputtering at a high bias. Steep, deep grooves and vias with aspect ratios up to 3 were found to be completely filled with the aluminum film by deposition at resputtering rates higher than 50%. It was also found that substrate biasing has a decisive effect on giving aluminum films an almost complete (111) crystallographic texture.
1472
R. A. Levy, S. M. Vincent and T. E. McGahan
This study describes the use of x‐ray fluorescence as an analytical tool for determining phosphorus concentration in phosphosilicate glass. By comparison with other available methods, we shall demonstrate that this direct measurement technique is accurate, simple, fast, reproducible, and nondestructive. With the use of this technique, flow and reflow profiles of phosphosilicate glass will be illustrated at different phosphorus concentrations and representative thermal cycles.
1480
T. Suzuki, Y. Inoue, T. Aoyama and M. Maki
A new approach to uniform growth, which directly modulates and controls the reactant gas concentration distribution within a reactor, has been proposed. A rotary disk (pancake) type reactor with a controlled supplemental gas adding system for regions of insufficient epitaxial layer thickness was designed and fabricated after consideration of gas flow patterns and reaction gas concentration distribution within the reactor. Simulation and control methods were developed to optimize the parameters of the multiple supplemental gas nozzles so that a uniform layer thickness distribution over a large range of susceptor radial directions could be achieved. Experiments using three supplemental nozzles showed that this system and control method could achieve deviations in thickness of less than ± 1% both within a wafer and within a growth lot.
1487
M. Tanielian and S. Blackstone
The resistivity, composition, and microstructure of sputtered titanium silicide films from a composite
target were investigated as a function of substrate temperature
in the range of
. We find that there are essentially three distinct regimes of properties, for
,
, and
. The oxygen incorporation, oxidation sensitivity, and resistivity of the films decrease as the substrate temperature increases. The most notable observation was that the physical properties of the films in the temperature range of 450°–600°C are similar to fully reacted titanium disilicide films formed in a furnace anneal at 900°C, and, in addition, they are oxygen free. In order to explain this result, we had to assume that the surface substrate temperature was several hundred degrees higher during sputtering than what the macroscopic measurements of the bulk substrate temperatures would indicate.
1492
K. Takahashi, J. Miyahara and Y. Shibahara
TECHNICAL NOTES
1495
Fumio Mizuno, Makoto Kato, Tooru Koizumi, Yoichi Takehana, Katsuro Sugawara and Keiji Mori
1496
K. Kugimiya
1498
R. L. Jones, S. R. Jones and C. E. Williams
1502
Jiri Marek, Roy Geiss, Larry M. Glassman and Martin P. Scott
ACCELERATED BRIEF COMMUNICATIONS
1505
E. Wang, N. Kimura and M. Greenblatt