REVIEWS AND NEWS
275C
W. Bruce Darlington and Marino Y. C. Woo
The Edward Weston Summer Fellowship Report
295C
Jeanne E. Pemberton
The Colin Garfield Fink Summer Fellowship Report
298C
Eric E. Bancroft
The Joseph W. Richards Summer Fellowship Report
300C
Raymond N. Dominey
ELECTROCHEMICAL SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
1651
Henry Leidheiser Jr., Alton F. Rauch, Elhoseny M. Ibrahim and Richard D. Granata
The purpose of these studies is to obtain a better understanding of the role which antimony plays in accelerating the corrosion of tin. Tin‐antimony alloys were prepared by electrodeposition and the corrosion rates were determined from polarization data obtained in deaerated 0.33M citric acid. The corrosion rates were linearly related to the antimony concentration in the alloy and were described by the following equation

where
is the antimony concentration in the tin in ppm. A mechanism is proposed in which small amounts of antimony oxide on a tin substrate catalyze the hydrogen evolution reaction. Nitrite additions to deaerated citric acid greatly accelerated the corrosion rate of unalloyed tin. The effects of nitrite were described by the following equation

where
is the nitrite concentration in the citric acid in ppm. The nitrite results and the great effect of antimony on the corrosion rate were attributed to the fact that a partially oxidized surface serves as a remarkably effective catalyst for the hydrogen evolution reaction on tin.
1658
Henry Leidheiser Jr., Gary W. Simmons, Sandor Nagy and Svetozar Musić
1662
S. C. Tjong, R. W. Hoffman and E. B. Yeager
Binary iron‐base alloys containing chromium additions of 3, 9, 12, and 18% were passivated in borate buffer (pH 8.4). The passive films formed on these alloys were investigated by Auger, ESCA, and SIMS techniques. For the Fe‐3Cr alloy passivated in the potential range 0.65–1.45V vs. RHE, the Auger spectra showed negligible Cr in the passivation layer. For the Fe‐9Cr, Fe‐12Cr, and Fe‐18Cr alloys, the Cr content was lower at the surface of the passive film and passed through an apparent maximum within the film. ESCA measurements indicate that the passive film of Fe‐18Cr alloy has a higher content of bound water in the form of OH− than Fe‐3Cr alloy. The SIMS results for the Fe‐Cr alloys generally confirm the relative measurements of Cr in the passive film found from Auger measurements.
1668
S. W. Smith, W. M. Vogel and S. Kapelner
1670
Johnsee Lee and J. R. Selman
The current distributions at parallel‐plate electrodes in an electrochemical flow reactor with a separator are calculated using the orthogonal collocation technique. The effects of separator and electrode resistance are taken into account, in addition to the effects of reactor geometry, mass transfer, and reaction kinetics. It is found that the presence of a separator and electrode resistance may contribute to a marked smoothing of the current distribution if the current tab is located at a properly chosen position. The results also demonstrate the value of model calculations for the optimization of cell design in the case of compartmented cells.
1678
J. D. Jorgensen, R. Varma, F. J. Rotella, G. Cook and N. P. Yao
1681
Tomokazu Matsue, Masamichi Fujihira and Tetsuo Osa
By controlled potential electrolyses in the presence of α‐cyclodextrin (α‐CD) in the electrolyte solution, the preferential reduction of o‐nitrophenol in a mixture of o‐ and p‐nitrophenol was achieved. The ratio of the decrease in the concentration of the o‐isomer to that of the p‐isomer,
, was ca. 10 in the presence of α‐CD in solution; whereas, the ratio was only 2.2 in the absence of α‐CD, indicating that the o‐isomer was reduced with good selectivity by the addition of α‐CD. These phenomena may be caused by the cathodic shift in the reduction potential of the p‐isomer resulting from the selective inclusion of the p‐isomer into the cavity of α‐CD. α‐CD adsorbed or immobilized on graphite electrodes has a similar effect; however, the ratios observed on the electrodes were not high (3.7 and 3.0, respectively).
1685
Jiri Prejza, Ingemar Lundström and Terje Skotheim
The formation of polypyrrole on some metallic films (Pt, Pd, Ti, Au, Ni, Cr, In, Al, Fe, Ag, etc.) has been studied under potentiostatic and galvanostatic conditions. The role of pyrrole and the fluoborate ion in the polymerization process has been investigated at room temperature. From the analysis of galvanostatic current‐potential curves it has been possible to distinguish the particular processes: initiator formation, polymerization, polymer degradation, and gas evolution. The polymerization in acetonitrile is indirectly initiated with a reaction order of ≈1 with respect to the
concentration. There are at least two different kinds of polypyrrole, depending on polymerization potential, that differ structurally. The formation of polymers on nonpolarized electrodes has also been observed.
1689
S. Ardizzone, A. Carugati, G. Lodi and S. Trasatti
The kinetics of chlorine evolution on ruthenium dioxide based films supported on titanium and quartz is investigated as a function of the intimate structure of the catalyst surface. The latter is modified by changing the temperature of pyrolysis of
and is characterized by measuring the amount of charge exchanged with the solution when the potential is varied within a range where no electrode reaction takes place. The results allow distinguishing between macro‐ and micro‐roughness of the surface. Chlorine evolution appears to be sensitive to the former but not to the latter.
1694
B. L. Papke, M. A. Ratner and D. F. Shriver
Two ion‐transport mechanisms are described for ion transport in polyether‐alkali metal salt complexes: an intrahelical jumping process along crystalline (helical) regions of the polymer, and a transport process in the amorphous regions which is dependent on formation of fourfold coordination sites via mutual motion of ether oxygens from two or more polymer chains. The intrahelical jumping process may exhibit Arrhenius behavior, while transport in the amorphous regions should behave like a configurational entropy dominated process, showing a temperature dependence like
, where
is the equilibrium glass transition temperature. For the highly crystalline poly(ethylene oxide) ·
complexes, an Arrhenius behavior is observed to dominate, whereas for the amorphous polyether · salt complexes the configurational entropy behavior is observed. Even for the highly crystalline complexes, however, amorphous regions separate the crystalline regions of the polymer, and segmental motion of the polymer chains is postulated to be crucial here as well. The models are consistent with the observed frequency‐dependent ionic conductivity, as well as spectroscopic, x‐ray, thermal, and physical characterization measurements. They provide a reasonable microscopic picture for ion motion and yield testable predictions concerning the dependence of the ionic conductivity on pressure, temperature, and crystallinity.
1701
Claude Levy‐Clement, Adam Heller, W. A. Bonner and B. A. Parkinson
1705
M. E. Langmuir, M. A. Parker and R. D. Rauh
1710
M. Sakashita, H. ‐H. Strehblow and M. Bettini
1716
J. J. Kester, T. E. Furtak and A. J. Bevolo
New aspects of molecular interactions in corrosion inhibition are reported in this first investigation of benzotriazole on copper using surface enhanced Raman scattering (SERS). The observation of hysteresis in the Raman intensity of concentrated solutions as a function of applied voltage is attributed to a conformation or bonding rearrangement in the protective layer. Also, a photoalteration of the benzotriazole complex, which occurs during anodization, produces improved corrosion resistance and increases the Raman activity. The ability of SERS to detect these photoaltered layers provides a new probe for corrosion studies.
1719
Patrick M. Dhooge, David E. Stilwell and Su‐Moon Park
1724
P. Rasiyah, A. C. C. Tseung and D. B. Hibbert
The formation of high valence oxides of Ni and Co on
at potentials before oxygen evolution commences was studied by controlled potential coulometry, cyclic voltammetry, and by galvanostatic charging. Three oxides are formed at 1.25, 1.31, and 1.40V vs. a dynamic hydrogen electrode (DHE) in
at 25°C, and the charges passed in their formation are approximately in the ratio 1:1:2. It is suggested that the transitions are
,
, and either all
or tetrahedrally coordinated
. The total charge passed to form higher oxides is 9.7% of the maximum possible charge if all the cations in the
electrode are oxidized to the +4 state. For
of 43 m2g−1, approximately 8% of the unit cells are found at the surface. This suggests that the formation of higher oxides is limited to the surface of the
particles. Analysis of the controlled potential coulometry results indicates that oxide formation obeys first‐order kinetics.
1727
Jacob Jorne
A cumulative flow channel is suggested in which the flow is fed uniformly through a porous wall facing the active electrode. The velocity distributions are solved using a perturbation method. The solution for the two‐dimensional convective diffusion indicates that for the case of zero entrance velocity, the surface is uniformly accessible to mass transfer, and the limiting current is uniform. The cumulative flow channel is proposed as a unique flow system that exhibits uniform accessibility to mass transfer.
1733
W. Gissler, A. J. McEvoy and M. Graetzel
1737
T. Skotheim, L. ‐G. Petersson, O. Inganäs and I. Lundström
Highly stable photoanodes based on single crystal n‐Si protected with a thin coating of Pt and electrochemically grown polypyrrole films have been studied. A power conversion efficiency of 5.5% under illumination of 55 mW/cm2 tungsten‐halogen light is reported with an iodide/triiodide electrolyte. The cells exhibit long‐term stability over a time period of weeks. The operating characteristics of the junctions yield high fill factors and rapid electron transfer kinetics at the interface. Values of the junction quality factor as low as 1.1 have been achieved showing almost ideal Schottky junction behavior. The open‐circuit voltage as a function of the redox potential of the electrolyte shows substantial fermi level pinning at the interface. The physical structure of the junctions has been studied with AES sputter profiling techniques. The main factor limiting the power conversion efficiency of the present devices is low short‐circuit photocurrent due to light absorption in the concentrated iodide/triiodide electrolyte.
1742
G. Nagasubramanian, Bob L. Wheeler, Fu‐Ren F. Fan and Allen J. Bard
TECHNICAL NOTES
1745
P. G. Glugla and V. J. DeCarlo
1747
K. Kinoshita and S. C. Leach
1749
Hans S. Hartmann and Raymond A. Sutula
1752
Kohei Uosaki and Hideaki Kita
1754
Donald R. Franceschetti and J. Ross Macdonald
SOLID-STATE SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
1757
H. P. Vyas, G. D. Kirchner and S. J. Lee
1760
Noboru Shiono, Osaake Nakajima and Chisato Hashimoto
An electrical characteristic degradation in MOSFET's due to the substrate hot‐electron injection into the gate
layer has been examined through long‐term stress aging with high substrate bias
applied at high temperatures. Experimental evidence of interface trapped charge generation at the
interface, besides electron trapping, is presented. This effect leads to larger positive threshold voltage
shifts than positive flatband voltage
shifts. Generated interface trapped charges are annihilated during annealing above 250°C, whereas trapped electrons cannot be discharged by the same annealing. The empirical
shift equation, for devices with 30 nm thick gate
layer under 5V gate bias applied, is expressed approximately as
. Here,
,
, and the units of the quantities are
,
,
, and
.
and
shifts for the device fabricated with direct electron beam lithography are also shown to appear faster than for a device fabricated with conventional photolithography, due to high trap concentration in gate
and high leakage currents for EB fabricated device.
1765
R. M. Levin
The interaction between phosphosilicate glass films and water vapor has been studied at the temperature range 70–100°C, using infrared spectroscopy. The films were deposited at 640°C using low pressure chemical vapor deposition. The infrared spectra change significantly during the exposure of the films to water vapor. In spite of the observed decrease in the intensity of the P=O band it has been found that phosphorus ions do not outflow from glasses that contain less than 8 m/o phosphorus oxide. The diffusion of water in the films can be described by a single activation energy, which increases with increasing phosphorus oxide concentration. Densification of the glass by means of heat‐treatment substantially increases the film resistance to water absorption. The densification of the phosphosilicate glass has been studied by infrared spectroscopy and etch rate measurements. The efficiency of the densification increases with increasing the temperature and time of the heat‐treatment. The effectiveness of the ambients used in this study can be ranked in the order:
.
1770
G. Smolinsky, T. M. Mayer and E. A. Truesdale
1773
G. M. Samuelson and K. M. Mar
The correlations of physical and electrical properties of PECVD
films with their composition ratios (Si/N and Si‐H/N‐H) are explored and compared. The four physical properties considered include refractive index, absorption edge, mechanical stress, and density. Both refractive index and absorption edge show very similar behavior in their correlations with Si/N and Si‐H/N‐H. Their correlations with Si/N show a distinct deposition condition dependence while those with Si‐H/N‐H indicate, to within experimental error, deposition condition independence. The other two physical properties exhibit similar behavior: a parabolic dependence on Si/N with a minimum at
and no correlation with Si‐H/N‐H. The two electrical properties considered are dielectric and d‐c conductivity. In the frequency range 103–106 Hz, two distinct absorption peaks are observed for films with the respective combinations of high Si‐H and low N‐H and high N‐H and low Si‐H concentrations. In d‐c conductivity, only one
of the three parameters (
,
,
) that characterize the Frenkel Poole conduction mechanism shows an apparent correlation with conductivity (σ). However, σ is quantitatively demonstrated to correlate better with Si‐H/N‐H than with Si/N.
1778
Joe Steinberg
1782
E. Bauser and G. A. Rozgonyi
1786
H. J. Stein
Chemical bonding changes and electrical effects of hydrogen implantation into silicon nitride have been investigated. Silicon nitride films were prepared by chemical vapor deposition from the decomposition products of
and
gases onto silicon substrates at 850°C. Implantation of either hydrogen or deuterium causes Si‒H bond formation by transferring deposition‐incorporated hydrogen from nitrogen to silicon bonds. The implanted hydrogen isotope, however, bonds predominantly on nitrogen. Displacement damage, which causes the N‐H band to broaden and shift to lower frequencies, is reduced by annealing at 500°C, and a loss of both N‒H and Si‒H bonds occurs when implanted films are annealed at temperatures >500°C. The observed electrical effects of hydrogen implantation of silicon nitride followed by annealing at 500°C are increased equilibrium positive charge, decreased charge transport, and enhanced charge trapping and retention. A correlation between deep traps and Si‒H bond formation in silicon nitride is suggested to explain the electrical effects.
1791
Len Mei, Michel Rivier, Young Kwark and Robert W. Dutton
The electrical characteristics of polycrystalline silicon layers are closely related to their grain structure. This paper describes a comprehensive study of the grain growth of polysilicon under a wide range of doping and processing conditions. A grain‐growth model has been developed and implemented in the SUPREM process simulator, and the simulated results are compared to those obtained by transmission electron microscopy for As‐, P‐ and B‐doped polysilicon. These results indicate that n‐type dopants increase the growth rate whereas the p‐type dopant has a negligible effect.
1795
T. H. Miers
1800
K. H. Nicholas and R. J. Tree
The misregistration between patterns in integrated circuits can be due in part to the masks. Mask errors can be simulated by writing different patterns on the same mask. The patterns can be arranged to form thin film resistors in a bright chrome mask and the resistor value can be used to calculate misregistrations. Normally the two patterns have to be aligned to get useful results. This paper, however, describes patterns that do not require alignment and this extends the use of the measurement technique to the assessment of the long term mask making errors and errors in copying. It is shown that the technique can be accurate to better than ±0.05 μm and an evaluation of runout effects in mask copying is described.
1803
W. J. M. J. Josquin and Y. Tamminga
In order to reveal the mechanism of oxidation inhibition in nitrogen‐implanted silicon, the 15N(p, αγ)12C resonant nuclear reaction has been applied to obtain detailed information on nitrogen concentration profiles in silicon. It appears that the oxidation resistance is caused by an extremely thin (<3 nm) nitrogen‐rich layer at the
interface. The formation of this interfacial nitride‐like layer is the result of complicated redistributions of the nitrogen which take place during annealing and oxidation. It is shown that implantation of nitrogen ions into source and drain areas of an MOS transistor can be used to inhibit further growth of the gate oxide in these areas during a subsequent oxidation and thus allows a selective oxidation of polysilicon gates. This provides a novel technique for obtaining self‐aligned contact windows to the source and drain regions. Finally reverse current measurements on gate‐controlled diodes show that the bulk and surface generation currents in the nitrogen‐implanted layer are as low as for unimplanted reference wafers, provided adequate experimental conditions are applied.
1811
S. Solmi, M. Severi, R. Angelucci, L. Baldi and R. Bilenchi
This paper presents the results of an extensive experimental investigation on the electrical properties of heavily As‐ and P‐doped polycrystalline silicon (poly‐Si) films thermally or CW‐laser annealed. The minimum resistivity values achievable with different annealing treatments are discussed in terms of grain size, carrier concentration, and electron mobility. After thermal annealing, the As‐doped films (0.44 μm thick) have a minimum sheet resistivity of 30 Ω/sq compared to 12 Ω/sq in similarly P‐doped samples. This is due to both carrier concentration and electron mobility being lower in As‐doped samples. Mobility values of 18 and 31 cm2/V·sec are achieved in As‐ and P‐doped poly‐Si films, respectively, for the highest carrier concentrations obtainable by thermal treatments. With measurements on heavily doped single crystal silicon we have found that the ionized impurity scattering depends on the nature of the ion and is stronger for As. Moreover, the grain boundary scattering is anomalously high in thermally annealed, As‐doped poly‐Si films. Laser annealing greatly reduces grain boundary scattering in As‐doped films also without a significant increase of grain size. On the contrary, in poly‐Si films doped with P to its solid‐solubility limit (
at 1050°C) CW‐laser annealing is not essential to obtain mobility values near to those of single crystal silicon.
1819
D. L. Malm and J. E. Riley Jr.
Composition profiles of the boron distribution in borosilicate glasses are shown to be dependent on the mode of sample preparation. Surfaces prepared for analysis by either abrasive polishing or saw cutting exhibit a boron gradient, the boron concentration increasing gradually to a constant level at 1–2 μm, Conversely, profiles for surfaces prepared by impact fracture show no significant change with depth.
1822
L. M. Ephrath and R. S. Bennett
1826
E. Guerrero, H. Pötzl, R. Tielert, M. Grasserbauer and G. Stingeder
A model for As clustering in single crystal silicon is presented that allows for the participation of arbitrary numbers of As ions, electrons, and arbitrarily charged vacancies. From this model the saturation behavior of the concentration of unclustered, electrically active As impurities is derived. It is shown that saturation (or electrical solubility) demands the participation of at least one negative charge in the formation of positively charged clusters, be it electron or negative vacancy. By analysis of our own experimental results and those by other authors, this general cluster model indicates that the participation of exactly one negative charge is the most likely case. In the course of this discussion the equilibrium saturation concentration of electrically active As is deduced from experiment as a function of temperature.
1831
T. Tamamura, K. Sukegawa and S. Sugawara
The ultimate resolution of the high contrast negative electron resist, chloromethylated poly‐α‐methylstyrene, was investigated by exposing thin films with 10 nm diam, 39 kV electron beam on a thin
substrate. The resolution of the negative resist showed a significant dependence on initial resist thickness and molecular weight of polymer. The swelling of cross‐linked polymer during development limits the pitch resolution, which showed a remarkable improvement by the reduction in the resist thickness and the molecular weight. Rather smaller initial thickness and molecular weight dependences of the resolution were observed in the minimum linewidth achieved, which seems to be limited by the size of cross‐linked polymer chains. The highest resolution pattern of 23 nm wide lines on 82 nm pitch was delineated in a thin film of a low molecular weight resist.
1835
Suresh T. Kshirsagar, H. Bradford Thompson and Jimmie G. Edwards
1840
A. K. Misra, D. P. Whittle and W. L. Worrell
TECHNICAL NOTES
1845
E. E. Crisman, Y. M. Ercil, J. J. Loferski and P. J. Stiles
1848
K. A. Bezjian, Henry I. Smith, J. M. Carter and M. W. Geis
ACCELERATED BRIEF COMMUNICATIONS
1851
Per Carlsson and Bertil Holmström
1853
W. K. Istone and R. J. Brodd