Batteries and Energy Storage
A55
Yong Min Lee, Young-Gi Lee, Yong-Mook Kang and Kuk Young Cho
The high rate discharge behavior of a lithium-ion secondary battery (LIB) in which each
and Li metal corresponds to the cathode and the anode is investigated with the introduction of functional additives. Representative additives such as vinylene carbonate, tris(pentafluorophenyl)borane (TPFPB), and biphenyl are generally chosen for anode stabilization, anion reception, and cathode protection, respectively. Even if there is no result showing the correlation between high rate performance and electrolyte, TPFPB apparently improves the high rate performance of LIB. This impressive result may provide the possibility that the introduction of a functional additive can be another way to attain a high power density of LIB for application in hybrid electric vehicles or electric vehicles.
A59
Colin Wessells, Riccardo Ruffo, Robert A. Huggins and Yi Cui
The electrolytic stability windows of several aqueous electrolytes were investigated by a constant current method. The electrode potential range depended upon the value of the imposed current. The magnitude of this behavior varied with the salt solution, its concentration, and pH of the electrolyte. At a leakage current density of
, a 5 M solution of
had an electrolytic window of 2.3 V, spanning from −0.55 to 1.75 V with respect to the standard hydrogen electrode. These results demonstrate the feasibility of operating lithium batteries at voltages appreciably above the theoretical decomposition voltage of water.
A62
Andrew van Bommel and J. R. Dahn
Fuel Cells and Energy Conversion
B47
Wenzhen Li and Pradeep Haldar
A carbon supported core-shell PtNi@Pt nanoparticle catalyst was synthesized through a two-step solution-phase reduction method, and it demonstrated a 5.4 times higher specific activity to an oxygen reduction reaction than a conventional Pt/C catalyst by using a rotating disk electrode in a three-compartment electrochemical cell, which could be attributed to the modified electronic structure of the Pt surface layer.
Corrosion, Passivation, and Anodic Films
C13
Jaganathan Ulaganathan and Roger C. Newman
Small iron electrodes were reactivated from the passive state in pH 4.7 acetate buffer. An inverted Tafel type of behavior was observed and interpreted in terms of thermodynamic control of the reactivation kinetics: The dissolution rate cannot exceed the value at which the interfacial concentration of
equals the concentration that is in equilibrium with an Fe(III) oxide or oxyhydroxide. Various minerals and their partially or wholly amorphous relatives were considered to try to identify the controlling solid at the interface.
Electrochemical/Chemical Deposition and Etching
D19
Hsyi-En Cheng, S. H. Hsiao and Deng-Maw Lu
D23
Toshio Haba, Hitoshi Suzuki, Hiroshi Yoshida, Haruo Akahoshi and Akira Chinda
Copper was selectively and anisotropically electroplated for a resistless metallization process using copper overburden with an inhibiting additive. Basic Red 12 (2-[3-(1,3-dihydro-1,3,3-trimethyl-2H-indol-2-ylidene)-1-propenyl]-1,3,3-trimethyl-3H-indolium chloride) was used as an inhibiting additive in an electroplating bath. When this additive was added, copper overburden was observed on the surface to have features without accelerating additives. The shapes of the deposited copper varied as a function of the additive concentration and plating current density. This process shows significant advantages in fabricating micrometer copper structures without a patterned resist layer.
D26
Kazuo Kondo, Yushi Suzuki, Takeyasu Saito, Naoki Okamoto and Minoru Takauchi
High speed copper electrodeposition is needed to achieve the through silicon via (TSV) process with a high throughput. To inhibit electrodeposition on the top surface of the TSV, octadecanthiol (ODT) was microcontact-printed on the top surface. The ODT microcontact-printing effectively inhibits copper electrodeposition on the top surface. With sulfonated diallyl dimethyl ammonium chloride copolymer (SDDACC), V shapes were formed in the via cross section, and these shapes led to bottom-up via filling. We succeeded in filling
diameter and
deep vias within 37 min. This was achieved by shortening the off time to 100 ms, ODT microcontact-printing, and adding 1 mg/L SDDACC additive.
D29
Luiz Henrique Dall’Antonia, Norma R. de Tacconi, Wilaiwan Chanmanee, Hari Timmaji, Noseung Myung and Krishnan Rajeshwar
D33
C.-C. Yang, F. R. McFeely, P.-C. Wang, K. Chanda and D. C. Edelstein
A selective chemical vapor deposition process of a ruthenium (Ru) metal capping layer was investigated for Cu interconnects in ultralarge scale integrated circuits. X-ray fluorescence spectroscopy determined the Ru deposition selectivity as a function of the deposition temperature and substrate materials. The feasibility of the selective Ru metal capping layer in the Cu interconnects for nanoelectronic applications was checked via a comprehensive evaluation including both electrical and reliability.
Dielectric Science and Materials
G33
Y. J. Cho, J. W. Mah, C. Y. Kim, H. Kim, H. J. Lee, H. J. Kang, D. W. Moon, S.-O. Kim and M.-H. Cho
G37
C. Radtke, C. Krug, G. V. Soares, I. J. R. Baumvol, J. M. J. Lopes, E. Durgun-Ozben, A. Nichau, J. Schubert and S. Mantl
G40
Névine Rochat, Aurélie Tauzin, Frédéric Mazen and Laurent Clavelier
G43
C. H. Yang, G. D. Hu, W. B. Wu, J. C. Wang and X. Wang
Metal–ferroelectric–insulator–silicon capacitors with a
(BFMO) ferroelectric film and a
(BTO) insulator have been fabricated. The electrical properties of 300 nm thick BFMO were investigated for different BTO thicknesses. The experimental results show that BFMO/BTO (50 nm) exhibits the largest maximum memory window. Furthermore, the trapped and mobile positive charges initiate at ±7 and ±8 V, respectively. Compared with BFMO/BTO (30 nm) and BFMO/BTO (70 nm), the BFMO/BTO (50 nm) shows a relatively long retention time.
G47
Sarmistha Basu, K. Ramesh Babu and R. N. P. Choudhary
The measured coupling coefficients for 0–3 type multiferroic composites are usually inferior to the theoretical prediction. To pole these composites, it is important to inhibit the percolation of the low resistive magnetostrictive phase in a piezoelectric matrix. To yield 0–3 type composites, a synthesis process has been optimized to homogeneously disperse cobalt iron oxide (magnetostrictive) in the lead zirconate titanate (piezoelectric) matrix. The analyses of the impedance spectra in conjunction with structural and microstructural features of these composites could be a valuable tool to understand the nature of the piezoelectric–magnetostrictive interface for an effective elastic coupling.
Semiconductor Devices, Materials, and Processing
H141
Sung-Min Yoon, Shin-Hyuk Yang, Soon-Won Jung, Chun-Won Byun, Sang-Hee Ko Park, Chi-Sun Hwang and Hiroshi Ishiwara
H144
Hsiao-Wen Zan, Wei-Tsung Chen, Cheng-Wei Chou, Chuang-Chuang Tsai, Ching-Neng Huang and Hsiu-Wen Hsueh
Instead of the conventional furnace annealing process with a temperature higher than
, two low temperature annealing methods are successfully demonstrated to suppress the instability problem of amorphous indium gallium zinc oxide (IGZO) thin film transistors (TFTs). With adequate Nd:yttrium aluminum garnet laser (266 nm) annealing energy density or Xe excimer UV lamp (172 nm) irradiation time, the on voltage shift is greatly suppressed from over 10 to 0.1 V. The influence of laser energy density and UV lamp irradiation time on the performance of IGZO TFTs is also investigated and explained. The proposed methods are promising for the development of amorphous IGZO TFTs on flexible substrates.
H147
Hee-Sub Hwang, Jae-Hyung Lim, Jin-Hyung Park, Eun-Suck Choi, Jin-Woo Ahn and Jea-Gun Park
We investigated the effect of hydroxyethyl cellulose (HEC) concentration in the alkaline slurry on the surface qualities of polished silicon wafers after touch polishing, such as the number of remaining particles and the haze level. They significantly decreased and saturated over the addition of a 0.2 wt % HEC. We attributed these surface quality enhancements to a formation of nanometer-sized passivation layers onto the silicon wafer and colloidal silica surfaces during touch polishing. The formation of passivation layers were shown by the results of investigations with an average particle size, the zeta potential of abrasives, the contact angle, and X-ray photoelectron spectroscopy measurements.
H151
S. J. Lim, Jae-Min Kim, Doyoung Kim, Changsoo Lee, Jin-Seong Park and Hyungjun Kim
H155
Jong-Young Cho, Hao Cui, Jin-Hyung Park, Sok-Ho Yi and Jea-Gun Park
H159
S. Z. Rahaman, S. Maikap, H.-C. Chiu, C.-H. Lin, T.-Y. Wu, Y.-S. Chen, P.-J. Tzeng, F. Chen, M.-J. Kao and M.-J. Tsai
H163
Ping-Wei Huang and YewChung Sermon Wu
An AlGaInP-based vertical light emitting diode (LED) comprising double roughened (GaP and n-AlGaInP) surfaces and a bottom metal reflector was fabricated by surface-etching and wafer-bonding technologies. The roughened GaP surface was created by photolithography and wet etching, while the AlGaInP surface was roughened by inductively coupled plasma dry etching. The output power of the double roughened LED could reach 5.88 mW, which was 2.56 times higher than that of the conventional LED. This is because the double roughened surfaces can provide photons multiple chances to escape from the LED surface and can redirect photons.
H166
Fu-Yen Jian, Ting-Chang Chang, Ann-Kuo Chu, Shih-Ching Chen, Te-Chih Chen, Yung-en Hsu, Hsueh-chih Tseng, Chia-Sheng Lin, Tai-Fa Young and Ya-Liang Yang
This article proposes an edge-Fowler–Nordheim (FN) tunneling method to make silicon–oxide–nitride–oxide–silicon thin film transistors possess not only 2 bit nonvolatile memory but also transistor switch functions. The 2 bit memory status is determined by measuring drain or source gate-induced drain leakage current, which can be suppressed by hole injection and electron erase after edge-FN tunneling. Because charge injection mainly occurs at the drain or source side during edge-FN tunneling operation, the device retains its transistor switch function without a threshold voltage shift during memory operation.
H169
S. Arulkumaran, S. Vicknesh, G. I. Ng, Z. H. Liu, M. Bryan and C. H. Lee
Sensors and Displays: Principles, Materials, and Processing
J39
Yong-Seok Park, Kwang-Hyuk Choi, Han-Ki Kim and Jae-Wook Kang
We investigated the stacking sequence effect of indium zinc oxide (IZO)–Ag and IZO–Ag–IZO on the characteristics of multi stacked flexible transparent electrodes for organic photovoltaics. In spite of the similar sheet resistances of the IZO–Ag and IZO–Ag–IZO stacked electrodes, the optical transparency of the latter is much higher than that of the former in the wavelength region of 400–800 nm due to the effective antireflection in the symmetric oxide–Ag–oxide structure. Furthermore, the flexible organic solar cells (OSCs) fabricated on the IZO–Ag–IZO-stacked multilayer electrode showed a higher power conversion efficiency than those fabricated on the IZO–Ag–stacked multilayer electrode due to the higher optical transparency of the former electrode in the main absorption region of the poly(3-hexylthiophere) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6)
layers. This indicates that the multistacked electrode with the IZO–Ag–IZO sequence is more beneficial than that with the IZO–Ag sequence for low resistance and high transparency electrodes in flexible OSCs.
J43
Seung Yoon Ryu, Chang Ho Lee, Il Soo Oh, Seung Yong Song, Kyu Hwan Hwang, Hyeon Seok Hwang, Man Hyeop Han, Byoung Har Hwang, Hong Koo Baik, Youn Sang Kim et al
J47
Xuhui Xu, Yuhua Wang, Yanqin Li and Yu Gong
J50
M. K. Chong, Q. V. Vu and K. Pita
J53
Jun-Hyuk Park, Han-Ki Kim, Hosuk Lee, Hosun Lee, Sooyoung Yoon and Chang-Dong Kim
J57
Dongdong Jia
J62
Bo Yong Han and Kee-Sun Sohn
Although detailed information about divalent europium-doped
,
, and
phosphors and their binary mixtures and solid solutions is now well known, no attempt has been made to examine ternary
. In this regard, we employed high throughput, solid-state synthesis and characterization techniques aimed at screening the entire composition range of the ternary
library in terms of photoluminescence intensity, color chromaticity, and structure. We finally pinpointed two promising ternary phosphors,
and
, which would work best as reliable candidates for use in light emitting diode applications.
J65
Xiaotun Qiu, Jon Oiler, Jie Zhu, Ziyu Wang, Rui Tang, Cunjiang Yu and Hongyu Yu
This article described relative humidity (RH) sensing using a ZnO-based film bulk acoustic-wave resonator (FBAR). The resonant frequency of the FBAR decreased in a two-stage manner as the RH increased. For low RH, a frequency downshift of 2.2 kHz per 1% RH change was observed. This effect was attributed to water molecules replacing the adsorbed oxygen on the ZnO surface, thus increasing the density of the film. For high RH, a frequency downshift of 8.5 kHz per 1% RH change was obtained, which was due to the mass loading effect of the water layers formed on the ZnO surface.
J68
Ziqiang Jiang and Yuhua Wang
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K39
S. Zhu, T. P. Chen, Z. H. Cen, Y. C. Liu and Y. Liu
The optical properties of self-assembled gold nanoparticles on silicon substrate have been determined using ellipsometric analysis. The dielectric function of the nanoparticles is best represented by a Drude term and three Lorentz oscillators with the resonance energies at 1.26, 2.22, and 3.65 eV. The Lorentz oscillator at 3.65 eV is due to the interband transitions, while the other two oscillators are attributed to the splitting of the plasmon resonance of the spatially limited free electrons inside the nanoparticles. The splitting of plasmon resonance could be due to the influence of various factors such as the near-field interactions of adjacent nanoparticles, image effects of the substrate, imperfect spherical shapes of the nanoparticles, etc.
K43
H. T. Chang, W. Y. Chen, T. M. Hsu, P. S. Shushpannikov, R. V. Goldstein and S. W. Lee
Self-aligned stacked Ge nanolenses were fabricated by selective chemical wet etching of Ge dot/Si multilayers. After removal of Si spacers, Ge nanodots become more lenticular. Based on the results of Raman spectroscopy, this shape change is attributed to the strain relief of Ge nanodots. The geometrical modulation could also be greatly beneficial to the vertical self-alignment of Ge nanolenses during the etching process. In addition, the improved full width at half-maximum value of the photoluminescence emission can be attributed to the reduction in size and composition fluctuations within the stacked Ge nanolenses.
K46
Wei Huang, Li Fu, Yingchang Yang, Sai Hu, Chao Li and Zelin Li
We report here a facile electrochemical method on simultaneous fabrications of nanoparticles and three-dimensional (3D) porous films of Pb or Sn by a highly cathodic polarization of pure metals in a NaOH solution. The nanoparticles produced from the formation and decomposition of unstable metal hydrides were assembled into 3D porous structures with a hydrogen bubble template. The two 3D porous metal films exhibited a high electrocatalytic activity toward the electroreduction of oxalic acid. Moreover, the two 3D porous oxide surfaces of Sn and Pb prepared by air exposition and by electro-oxidation of the porous metal films of Sn and Pb, respectively, showed superhydrophobicity.
K49
Hee Jung Park and Yong Ho Choa
We investigated oxygen ionic conduction in fully dense, transparent polycrystalline yttrium-doped zirconia with an average grain size of
. We observed that the oxygen ionic conductivity across single grain boundaries in the nanostructured ceramic is 1 order of magnitude greater than that of the corresponding microstructured ceramic. Such an enhancement in the grain boundary is attributed to the high density of the sample.
K53
Emanuele Francesco Pecora, Alessia Irrera, Pietro Artoni, Simona Boninelli, Corrado Bongiorno, Corrado Spinella and Francesco Priolo
We demonstrated the heteroepitaxial growth of single-crystal faceted Ge nanowires (NWs) by electron-beam evaporation on top of Si(111) substrates. Despite the non-ultrahigh vacuum growth conditions, scanning electron microscope and transmission electron microscope images show that NWs have specific crystallographic growth directions ([111], [110], and [112]) and that specific surface crystallographic planes ({111} or {110}) correspond to the [110] and [112] growth directions. Moreover, we studied in detail the Ge NWs structural properties. The temperature dependence of the NW length and of the frequency of each crystallographic orientation has been elucidated. Finally, the microscopic growth mechanisms have been investigated.