Batteries and Energy Storage
A125
Robert E. Doe, Kristin A. Persson, Geoffroy Hautier and Gerbrand Ceder
First principles calculations have been used to explore the Li–Bi–F ternary phase diagram. Our results confirm the thermodynamic stability of previously observed phases and find no new phases in this system. Electrochemical voltage profiles for the reaction of Li and
are in reasonable agreement with experiment. The driving force to form ternary Li–Bi–F intermediates is small. We also investigated the effect of particle size on the reaction voltage and find a potential decrease when nanoscale vs bulk Bi forms upon reacting
with Li.
A129
Mao-Sung Wu, Chen-Yu Huang and Kun-Hao Lin
Ni-decorated carbon nanotube (CNT) film of a networklike architecture has been formed on a stainless steel substrate by electrophoretic deposition (EPD) in CNT suspension containing nickel nitrate. Adsorption of nickel ions on the CNTs increases the measured zeta potential and consequently favors the dispersion and EPD of CNTs. Nickel ions are reduced on the CNT surface to form Ni-decorated CNT film in the EPD process. The deposited nickel layer plays an important role in improving the adhesion, wettability, and electrochemical reaction of the film. Therefore, the Ni-decorated CNT film exhibits an excellent capacitive behavior compared with the bare CNT film.
A132
Tao Zhang, Nobuyuki Imanishi, Satoshi Hasegawa, Atsushi Hirano, Jian Xie, Yasuo Takeda, Osamu Yamamoto and Nigel Sammes
A136
Sen Zhang, Chao Deng and Saiyu Yang
A140
Fabio Rosciano, Jean-François Colin, Fabio La Mantia, Nicolas Tran and Petr Novák
A145
J. Morales, R. Trócoli and J. Santos-Peña
Fuel Cells and Energy Conversion
B107
Z. H. Bi and J. H. Zhu
B112
Tao Huang, Xiaoya Wang, Jihua Zhuang, Wen-Bin Cai and Aishui Yu
Porous ternary PtRuCo catalyst supported on a glassy carbon substrate was prepared by one-step electrochemical codeposition using an adsorbed hydrogen gas bubble as a dynamic template. The as-prepared catalyst was characterized by scanning electron microscopy and transmission electron microscopy. Methanol electro-oxidation on the as-prepared catalyst was investigated by cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy, and the results show that porous ternary PtRuCo catalyst has excellent electrocatalytic performance.
B116
B. Legros, P.-X. Thivel, Y. Bultel, M. Boinet and R. P. Nogueira
This study evaluates the acoustic emission (AE) technique for the detection of membrane dehydration in proton exchange membrane fuel cells during operation. The dehydration of the membrane owing to inefficient water management leads to drastic performance losses. Electrochemical impedance spectroscopy (EIS) and AE measurements were carried out during dehydration of Nafion samples. Results have shown that electrochemical parameters obtained from EIS yield monotonic exponential-like responses following the water loss. AE was shown to be sensitive enough to detect structural changes taking place at the last stages of dehydration.
Corrosion, Passivation, and Anodic Films
C17
Yan-Yan Song, Robert Lynch, Doohun Kim, Poulomi Roy and Patrik Schmuki
We report on an approach to obtain anodic self-organized
nanotube layers with a significantly improved tube morphology. Before the anodic tube growth, a rutile layer is formed on the Ti substrate by high temperature oxidation in air. This layer protects the tube tops during anodization against chemical etching in the fluoride-containing electrolyte. As a result, much longer (higher aspect ratio) nanotubes can be grown that still have an intact tube top (i.e., the formation of undesired etching-induced “nanograss” and “nanospikes” is suppressed). This technique is particularly significant for applications that require open tubes and coherent tube walls.
Electrochemical Synthesis and Engineering
E9
P. Vernoux, M. Guth and X. Li
Propane deep oxidation, as a model reaction, was investigated to illuminate the intrinsic electrochemical promotion of catalysis (EPOC) by a nanodispersed Pt/yttria-stabilized zirconia catalyst powder. The thermally induced back-spillover of
ions from the ionic ceramic support to the Pt particle’s surface was observed and confirmed to play a key role in enhancing the catalytic activity as an effective promoter. These results demonstrate that EPOC can be thermally induced without any electrical polarization by using nanoparticles of metallic catalysts supported on ionically conducting ceramics, which can be widely utilized as attractive alternative supports in various heterogeneous catalyses.
E12
Jonathan Mbah, Burton Krakow, Elias Stefanakos and John Wolan
Physical and Analytical Electrochemistry
F9
Masaki Yamagata, Soichiro Konno, Kazuhiko Matsumoto and Rika Hagiwara
A series of fluorohydrogenate ionic liquids (FHILs),
(
: alkylpyridinium cations and allylated quarternary cyclic ammonium cations), are prepared, and their physical and electrochemical properties are characterized. The viscosities and conductivities of alkylpyridinium-based FHILs increase and decrease, respectively, with an increase in the length of the side chain. The FHILs of allylated cations exhibit higher ionic conductivities than those of the corresponding propylated cations and even those of the ethylated cations in some cases, which is explained by differences in volume, charge distribution, and rotational freedom of the side chains according to quantum mechanical calculations. The electrochemical windows of the FHILs are around 4 V.
F13
Haiqing Jiang, Sho Sakurai and Koichi Kobayashi
F17
Yunjung Choi, Minsu Jung and Young-Kook Lee
Dielectric Science and Materials
G31
Chang-Po Hsiung, Jon-Yiew Gan, Shih-Hao Tseng, Nyan-Hwa Tai, Pei-Jer Tzeng, Cha-Hsin Lin, Frederick Chen and Ming-Jinn Tsai
In this work, reactively sputtered
films were reported to contain reduced Ti ions, the concentration of which correlates to the conductive channels formed in the film through percolation. Cells made on these films appear with different switching behaviors, depending on whether the as-fabricated cell intercepts the conductive channels. Films with a high population of conductive channels are “forming free” because most of the devices fabricated on them may intercept conductive channels and initially appear in the low resistance state.
G34
H. C. M. Knoops, A. J. M. Mackus, M. E. Donders, M. C. M. van de Sanden, P. H. L. Notten and W. M. M. Kessels
Semiconductor Devices, Materials, and Processing
H233
Chia-Feng Lin, Chun-Min Lin, Chung-Chieh Yang, Wei-Kai Wang, Yu-Chieh Huang, Jien-An Chen and Ray-Hua Horng
H238
M. Yang, T. P. Chen, L. Ding, J. I. Wong, Y. Liu, W. L. Zhang, S. Zhang, F. Zhu and W. P. Goh
H241
Sung Gyu Pyo, Myoungshik Kim, Hyungjun Kim and Sibum Kim
The purpose of this study is to investigate the planarization behavior of high selective ceria slurry in terms of topography and pattern density variation. Planarization experiments have been performed using ceria slurry with various initial step heights and surrounding pattern density on active trench and shallow trench isolation. The threshold step height was measured in various layouts which showed different pattern density ranges, and the pattern density effect on the threshold step height has been discussed. The planarization capability of high selective slurry and the removal rate of the high density plasma oxide are strongly dependent on the whole chip topography rather than on the micropattern density.
H244
Y.-J. Chang, Y.-W. Su, D.-H. Lee, S. O. Ryu and C.-H. Chang
Chemical bath deposition (CBD) is a commonly used and inexpensive technique to deposit a variety of semiconductor and oxide thin films for a variety of different applications. In this work, a continuous flow microreactor was used to better control the reacting flux present during the CBD reaction by offering a better temporal resolution. High quality CdS films at various thicknesses could be obtained by using a flux that avoided the formation of nanoparticles. The chemistry and growth kinetics of CdS CBD were elucidated using this microreactor. The results suggest that
ions formed during the thiourea hydrolysis reaction are the dominant sulfide ion source responsible for the CdS deposition.
H248
Windu Sari, Tae-Kwang Eom, Chan-Wook Jeon, Hyunchul Sohn and Soo-Hyun Kim
H252
Fang-Chung Chen and Yu-Jen Huang
Air stable ambipolar organic field-effect transistors containing p/n heterojunctions are achieved by passivating the electron trapping sites on the
surface. The morphology of the heterojunctions is controlled by the film thicknesses of p- and n-channel semiconductors, thereby affecting the device air stability and the electrical characteristics. Further, air stable complementary-like inverters, which are able to work both in the first and the third quadrants with a high gain up to 30, are also demonstrated.
H256
Sung Kyu Park, Yong-Hoon Kim, Hyun-Soo Kim and Jeong-In Han
H259
Nicholas G. Kubala, Pieter C. Rowlette and Colin A. Wolden
H263
Toshihide Takahashi, Shuichi Komatsu and Tatsuoki Kono
Pb-based solders are used as high temperature solders in power semiconductor devices. Although use of Pb is globally restricted, alternative materials are inadequate to replace Pb-based solder. This study aims to replace Pb-based solder with an intermetallic compound (IMC). Samples were produced to join a Si chip with evaporated Ag and Sn films onto a Ag-plated Cu substrate at 523 K for 10 s. As a result, the evaporated films were completely transformed into a
IMC. The IMC joint showed higher strength until 543 K and good heat-aging resistance at 423 K. Therefore, this joint would be promising in replacing Pb-based solders.
H266
Ruilong Xie, Thanh Hoa Phung, Mingbin Yu, Sue Ann Oh, Sudhiranjan Tripathy and Chunxiang Zhu
H269
Purushottam Kumar, Seung-Young Son, Jaeseok Lee, Feng-Chi Chang, Aniruddh Khanna, Arul Chakkaravarthi Arjunan and Rajiv K. Singh
H272
F. Fillot, S. Maîtrejean, F. Pierre and B. Chenevier
H275
Se-Yeon Jung, Tae-Yeon Seong, Hyunsoo Kim, Kyung-Soo Park, Jae-Gwan Park and Gon Namgoong
H278
Seyeoul Kwon, Jungwon Park and Philip D. Rack
H281
R. Yang, X. M. Li, W. D. Yu, X. J. Liu, X. Cao, Q. Wang and L. D. Chen
Multiform resistance switching (RS) effects, including two modes of bipolar RS effects and unipolar RS effect, have been observed in the same
(LCMO)/Pt structures by adjusting the thickness of Al electrode and implementing a forming process. When Al electrode is ultrathin (10 nm), a polarity reversal in bipolar RS can be obtained. The conversion from bipolar RS to unipolar RS can also be realized while increasing the thickness of Al (such as 50 nm). The transitions between these multiform RS effects derive from the changes in the Al/LCMO interface, which highlights the importance of the interface structure on the RS properties.
Sensors and Displays: Principles, Materials, and Processing
J61
Taeho Moon, Gun Young Hong, Hong-Cheol Lee, Eun-A Moon, Byung Woo Jeoung, Sun-Tae Hwang, Je Seok Kim and Byung-Gil Ryu
J64
R. Balakrishnaiah, Dong Woo Kim, Soung Soo Yi, Kwang Duk Kim, Sung Hoon Kim, Kiwan Jang, Ho Sueb Lee and Jung Hyun Jeong
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K45
Steffen Berger, Florian Jakubka and Patrik Schmuki
K49
Chih-Chieh Wang, Chi-Chung Kei, Ye Tao and Tsong-Pyng Perng
Miscellaneous
S9
Jie Shu