Batteries and Energy Storage
A111
H. T. Kuo, T. S. Chan, N. C. Bagkar, R. S. Liu, C. H. Shen, D. S. Shy, X. K. Xing and J.-F. Lee
A115
Prasant Kumar Nayak and N. Munichandraiah
A120
Yong Zhang, Yanghai Gui, Xingbing Wu, Hui Feng, Lizhen Wang, Aiqin Zhang, Xiaofeng Li, Tongchi Xia, Linsen Zhang, Peng Zhang et al
Fuel Cells and Energy Conversion
B91
Zhiyi Jiang, Changrong Xia, Fei Zhao and Fanglin Chen
B94
Nobuaki Ohguri, Atsuko Y. Nosaka and Yoshio Nosaka
B97
H. Chhina, D. Susac, S. Campbell and O. Kesler
B101
Fuqiang Liu and Chao-Yang Wang
As a key parameter in enabling the operation of high concentration methanol fuel cells, the water transport coefficient through the membrane must be reduced to between 0 and −1/6. We show that this coefficient can be lowered to −0.7 at
and under common cathode flow conditions using fully humidified air. A previously developed membrane electrode assembly based on a Nafion 112 membrane was used. The present result gives rise to the possibility of achieving a water-neutral state for use of pure methanol, i.e., with the water crossover coefficient of −1/6, under temperatures much higher than
and in active air-flowing direct methanol fuel cell systems with high power density.
B103
Shiquan Lü, Yuan Ji, Xiangwei Meng, Guohui Long, Tao Wei, Yanlei Zhang and Tianquan Lü
Electrochemical/Chemical Deposition and Etching
D49
D. H. van Dorp, J. H. den Otter, N. Hijnen, M. Bergmeijer and J. J. Kelly
The influence of electrochemical etching on the electroluminescence properties of n-type
- and
was investigated. Luminescence was generated by forward-biasing the semiconductor in an electrolyte solution containing a hole-injecting species. The emission properties of unetched, uniformly etched, and porous-etched substrates are compared. It is shown that the spectral distribution of the luminescence and the emission intensity strongly depends on photoanodic treatment.
Dielectric Science and Materials
G27
Tung-Ming Pan, Li-Chen Yen, Chun-Chin Huang and Wu-Ching Lin
Semiconductor Devices, Materials, and Processing
H191
Yasa Sampurno, Fransisca Sudargho, Yun Zhuang, Toranosuke Ashizawa, Hiroyuki Morishima and Ara Philipossian
This study explored the effect of different cerium oxide abrasive particle sizes in chemical mechanical planarization of
blanket plasma-enhanced tetraethylorthosilicate wafers. All polishing experiments were done with a polisher and tribometer capable of measuring shear force and down force in real-time. Coefficient of friction and removal rate were found to correlate well with the slurry median particle size distribution. Removal rate modeling based on particle size was explored to support the interpretation of the experimental results.
H195
Dongjo Kim, Seong Hui Lee, Sunho Jeong and Jooho Moon
We analyzed all-ink-jet printed organic thin-film transistors (TFTs) on plastic substrates. Multilayered organic transistors were created by a successive printing and annealing of silver nanoparticulate conductive ink, sol-gel dielectric ink, and organic semiconductor ink. Controls for interlayer compatibility and processing temperatures played an important role in determining the device performance of the multilayered solution-processed transistor. After the optimization of all the component materials and processing conditions, we fabricated the flexible TFT arrays, which exhibited good field-effect transistor characteristics and mechanical flexibility.
H198
Dong Hun Kim, Nam Gyu Cho, Ho-Gi Kim and Il-Doo Kim
H202
Jer-Chyi Wang, Chao-Sung Lai, Yu-Kai Chen, Chih-Ting Lin, Chuan-Pu Liu, Michael R.S. Huang and Yu-Ching Fang
H205
B. Brennan, M. Milojevic, H. C. Kim, P. K. Hurley, J. Kim, G. Hughes and R. M. Wallace
The effect of water and ozone as the oxidant in the atomic layer deposition (ALD) of aluminum oxide on the ammonium-sulfide-passivated
surface is compared using X-ray photoelectron spectroscopy (XPS) after each “half-cycle” of the ALD process. While the first half-cycle of the aluminum precursor tri-methyl aluminum (TMA) reduces the residual native oxides to within detection limits of XPS, the ozone oxidation process causes significant reoxidation of the substrate in comparison to the water-based process. Subsequent TMA pulses fail to remove the excess interfacial oxides caused by ozone oxidation, resulting in the formation of an oxide interlayer.
H208
Deok-Yong Cho, Jaewon Song, Yong Cheol Shin, Cheol Seong Hwang, W. S. Choi and Jae Kyeong Jeong
H211
Li-Yang Chen, Huey-Ing Chen, Shiou-Ying Cheng, Tzu-Pin Chen, Tsung-Han Tsai, Yi-Jung Liu, Yi-Wen Huang, Chien-Chang Huang and Wen-Chau Liu
The temperature-dependent characteristics of an
pseudomorphic high electron mobility transistor (PHEMT) with an electroless plated (EP) deposition approach are studied and demonstrated. Based on the low temperature and low energy deposition, the EP deposition approach can form a better metal–semiconductor interface with the reduction in surface damage. Experimentally, the EP-based device shows a significantly improved dc performance. Good experimental results, including a high Schottky barrier height of 0.831
, low ideality factor of 1.10 (1.32), high turn-on voltage of 0.75
, low reverse leakage current of 3.9
, improved threshold voltage of 
, and high maximum transconductance of 225.8
, are obtained at 300
. Moreover, the EP approach also has the advantages of easy operation and low cost.
H214
Chia-Chun Kao, Pang Lin, Li-Hsin Chan, Cheng-Chung Lee and Jia-Chong Ho
We investigated bottom-contact organic thin-film transistors based on
-benzyl naphthalene 1,4,5,8-tetracarboxylic diimides. The electrical characteristics were tested in both air and vacuum environments. n-Type semiconductors which are modified by fluorinated imide can be operated in ambient environment. The close packing of the fluorinated ester imide group leads to carrier mobility as high as
. The short distance between each molecule can be found via a single-crystal structure.
H218
Ye-Hwan Kim, Gisik Hong, Jong-Woo Kim, Sang-Kyun Kim, Namsoo Kim, Dong Kee Yi and Ungyu Paik
The constraints of corning on the W plug in W chemical mechanical planarization (CMP) were investigated by controlling the corrosion behavior and static etch rate of the W film. Poly(acrylic amide) (PAM) was used as an inhibitor to decrease the static etch rate of the W film. The interaction between PAM and the surface of the W film was determined by potentiostatic measurement using a potentiometer and by force measurement using an atomic force microscope (AFM). AFM results revealed that the adlayer of PAM formed on the W film, which prevented the oxidation of the W film. Consequently the addition of PAM suppressed the corning defect on the W plug in a W CMP test that used patterned wafers.
H222
R. H. Horng, C. C. Chiang, Y. L. Tsai, C. P. Lin, K. Kan, H. I. Lin and D. S. Wuu
H226
Chih-Ming Hsieh, Bing-Yue Tsui, Yu-Ren Hung, York Yang, Ryan Shen, Sam Cheng and Tony Lin
H229
Chia-Sheng Lin, Ying-Chung Chen, Ting-Chang Chang, Wei-Che Hsu, Shih-Ching Chen, Hung-Wei Li, Kuan-Jen Tu, Fu-Yen Jian and Te-Chih Chen
In this work, the negative bias temperature instability (NBTI) in low temperature polycrystalline silicon thin-film transistors in a darkened and in an illuminated environment was investigated. Experimental results reveal that the generation of interface state density
showed no change between the different NBTI stresses. Nevertheless, the degradation of the grain boundary trap
under illumination was more significant than that in the darkened environment. This phenomenon is mainly caused by the extra number of holes generated during the illuminated NBTI stress.
Sensors and Displays: Principles, Materials, and Processing
J55
Chandramouli Kulshreshtha, Namsoo Shin and Kee-Sun Sohn
J58
Jeong Rok Oh, Hoo Keun Park and Young Rag Do
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K41
Tsung-Chi Hung, Chia-Fu Chen and Wha-Tzong Whang