Batteries and Energy Storage
A151
Wilfried Sigle, Ruhul Amin, Katja Weichert, Peter A. van Aken and Joachim Maier
There is still some controversy about the mechanisms responsible for the delithiation of
. We studied the delithiation of both large single crystals and powder by electron energy-loss spectroscopy. It is shown that Li depletion leads to a change in the Fe valency, to an enhanced prepeak at the O K edge, and to a pronounced interband transition peak between 4 and 6 eV. Exploiting these spectral changes, the delithiation process was monitored, with the result that in the large single crystal, delithiation takes place by removal of Li from the surface-near region, whereas in small particles, Li is removed from the particle core.
A155
Mengqing Xu, Ang Xiao, Weishan Li and Brett L. Lucht
A159
Seung-Wan Song, Sung-Jin Hong, Ho Young Park, Young Chang Lim and Ki Chang Lee
A163
Yang-Kook Sun, Seung-Taek Myung, Chong Seung Yoon and Dong-Won Kim
A167
A. Caballero, L. Hernán, J. Morales, M. Olivares-Marín and V. Gómez-Serrano
In this work, we developed an easy method to suppress the irreversible capacity (IC) observed in disordered carbons acting as electrode materials in lithium batteries by limiting the amount of Li inserted in the first discharge to different nominal capacities. This strategy is quite effective with carbons with a high IC. To suppress IC, the proposed method improves capacity retention and rate capabilities.
Corrosion, Passivation, and Anodic Films
C21
Y. I. Kuznetsov, L. P. Kazansky, I. A. Seljaninov, D. Starosvetsky and Y. Ein-Eli
Electrochemical/Chemical Deposition and Etching
D53
E. Gileadi, O. Berkh and Y. Shacham-Diamand
Electroplating of magnetic alloys is often the preferred method of fabrication of micropermanent magnets for microelectromechanical system applications. Electroplated cobalt–platinum alloys have the desired magnetic characteristics. However, the observed current efficiency, the composition, and the magnetic properties of the deposit change with the amount of charge passed. This impedes the manufacturability of alloys. These changes are undoubtedly associated with changes in the composition of the bath, specifically the nature of the Pt-containing complex. Here we discuss the possible changes in the
complex and in the other components of the bath, employing the methods of voltammetry.
D57
J. J. Mallett, W. Shao, D. Liang and G. Zangari
The simultaneous underpotential codeposition of Cu and diffusion-limited overpotential codeposition of Au into Cu–Au alloy films is investigated from sulfuric acid solutions containing high concentrations of cupric ions and low concentrations of tetrachloroaurate ions. These conditions allow Cu to be deposited close to equilibrium, with the Cu fraction thermodynamically limited by the deposition potential. The dependence of the alloy composition on potential is described by a subregular solution alloying model. The average value of the bulk alloy minimum mixing enthalpy of
obtained from fits to this model agrees with the value of −6.35 kJ/mol assessed in the literature
D61
S. L. Toh, Z. H. Mai, E. Hendarto, H. J. Mak, J. C. Lam and L. C. Hsia
Laser-enhanced chemical etching with a 532 nm neodymium-doped yttrium aluminum garnet pulsed laser in KOH solution was used for sharpening conical tungsten nanotips which were prefabricated with a conventional electrochemical etch. The laser irradiation was incident axially on the tip apex. Due to different light absorption mechanisms by objectives in different sizes, the laser irradiation generates a controllable temperature gradient profile from the tip apex to the tip base. In the KOH solution, the etching rate varies with the temperature profile along the tip axis. The tip apex radius was greatly reduced, with the shape and aspect ratio in good control.
Electrochemical Synthesis and Engineering
E17
Aijian Zhang, Weimin Zhang, Jiaxing Lu, Gordon G. Wallace and Jun Chen
E20
L. Wang, H. Jia, X. Yu, Y. Zhang, P. Du, Z. Xi and D. Jin
Dielectric Science and Materials
G37
Seung-Yeon Kwak, Chaun Gi Choi and Byeong-Soo Bae
Fluorinated hybrid materials were synthesized for a solution-processable gate insulator. The surface energy was modified by perfluoroalkyl chains contained in the hybrid gate insulator itself. We investigated the initial morphology and growth mode of pentacene and the characteristics of organic thin-film transistors (OTFTs) to determine how these characteristics depend on the surface energy. Pentacene growth was changed from a layer-by-layer mode to a three-dimensional (3D) island growth mode at low surface energy. Tightly and uniformly grown pentacene grains at 3D island mode induced good OTFT performance, but the carrier mobility was degraded at very low surface energy due to the large amount of grain boundaries.
G40
Byungha Shin, Joël Cagnon, Rathnait D. Long, Paul K. Hurley, Susanne Stemmer and Paul C. McIntyre
G44
Tung-Ming Pan, Ching-Lin Chan and Tin-Wei Wu
Semiconductor Devices, Materials, and Processing
H285
Jae-Hong Kwon, Sang-Il Shin, Jinnil Choi, Myung-Ho Chung, Hyeyeon Ryu, Ute Zschieschang, Hagen Klauk, John E. Anthony and Byeong-Kwon Ju
This work reports on the fabrication of organic thin-film transistors (OTFTs) with a solution-based 6,13-bis(triisopropylsilylethynyl)pentacene by a drop-casting method, and the determination of the electrical properties of OTFTs having different source/drain interdigitated-finger electrodes. The results show that the hysteresis in transfer characteristics of the OTFTs depends on the variation of contact fingers. These hystereses lead to changes in threshold voltage, which originates from charge trapping/detrapping at or near the organic semiconductor/dielectric interface. These related phenomena also influence the device parameters such as the field-effect mobility, the on/off current ratio, and the gate current.
H288
R. Henríquez, P. Grez, E. Muñoz, E. A. Dalchiele, R. Marotti and H. Gómez
H292
Adam M. Urbanowicz, Kris Vanstreels, Denis Shamiryan, Stefan De Gendt and Mikhail R. Baklanov
H296
Dong Hun Kim, Seung-Hoon Choi, Nam Gyu Cho, YoungEun Chang, Ho-Gi Kim, Jae-Min Hong and Il-Doo Kim
H299
Hyung Gu Kim, Hyun Kyu Kim, Hee Yun Kim, Jae Hyoung Ryu, Ji hye Kang, Nam Han, Periyayya Uthirakumar, Dong Hyun Yu and Chang-Hee Hong
In this article, overcut-shaped periodic microstructures (OSPMs), embedded InGaN/GaN light-emitting diodes (LEDs), are fabricated using a 2 M aqueous KOH solution wet etching process. Inclined overcut microstructures are formed as the GaN
facets and GaN
facets with angles of 57 and 62°. This can be attributed to the crystallographic properties of GaN by the difference in etch rates between the Ga face and the N face. The light extraction properties of OSPM-LEDs are effectively extracted upside of the LED device by entirely deflected photons from the inclined overcut microstructures.
H302
R. P. Gupta, J. B. White, O. D. Iyore, U. Chakrabarti, H. N. Alshareef and B. E. Gnade
H305
Young-Hwan Kim, Jae-Hong Kwon, Sang-Il Shin, Byeong-Yun Oh, Hong-Gyu Park, Kyeong-Kap Paek, Byeong-Kwon Ju and Dae-Shik Seo
H309
Ho-Kyun Park, Jin-A Jeong, Yong-Seok Park, Seok-In Na, Dong-Yu Kim and Han-Ki Kim
We reported on the characteristics of an indium-free Ga-doped ZnO (GZO)/Ag/GZO multilayer electrode for use in bulk heterojunction organic solar cells. By inserting a very thin Ag layer between two GZO layers, we can fabricate a GZO-based transparent electrode with a low sheet resistance of
and a high optical transmittance of 87% at room temperature without postannealing. The power conversion efficiency (2.84%) of the organic solar cell fabricated on the GZO/Ag/GZO multilayer using neutral poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is much higher than that of the organic solar cell fabricated on the GZO electrode (1.57%) annealed at
. Indium-free GZO/Ag/GZO multilayer electrodes are expected to substitute for expensive indium tin oxide (ITO) electrode and decrease the cost of organic solar cells or flexible organic solar cells due to their comparable electrical and optical properties to those of crystalline ITO electrodes.
H312
Yeong Don Park, Jung Ah Lim, Donghoon Kwak, Jeong Ho Cho and Kilwon Cho
Sensors and Displays: Principles, Materials, and Processing
J69
Toru Takahashi and Sadao Adachi
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K53
Guoping Dong, Xiaofeng Liu, Xiudi Xiao, Qiang Zhang, Geng Lin, Zhijun Ma, Danping Chen and Jianrong Qiu
Using low temperature synthesized BCNO phosphors as raw materials, monodispersed BCNO nanoparticles
are obtained successfully after a two-step centrifugation. X-ray diffraction results indicate that these BCNO nanoparticles are mainly hexagonal BN phase. These BCNO nanoparticle-embedded polymer nanofibers with an average diameter of 300 nm are prepared by electrospinning. Photoluminescence spectra of these nanofibers indicate that the emission can be readily tuned by adjusting the C concentration in the BCNO phosphors. These nontoxic nanofibers with intense tunable emission may find potential applications in the fields of lighting, biological marker, optoelectronic nanodevices, etc.
K56
Fu-Lin Zheng, Gao-Ren Li, Xiao-Lan Yu and Ye-Xiang Tong
Here we have successfully fabricated
nanowires via an electrodeposition–heat-treatment method. The precursors prepared via electrodeposition possess many spheres which are amorphous, consisting of bismuth oxides and molybdenum oxides. After annealing at
for 2 h in air atmosphere, bismuth molybdate nanowires were synthesized from the sphere precursors. Scanning electron microscopy, electron-dispersive spectroscopy, X-ray diffraction, and selected area electron diffraction measurements were employed to characterize the bismuth molybdate nanowires. A possible growth mechanism for bismuth molybdate nanowires was proposed in this article.
Miscellaneous
S11
Ying Wang, Fei Cao, Zhongxiao Song and Chun-Hui Zhao