Batteries and Energy Storage
A171
Cheol-Min Park, Heechul Jung and Hun-Joon Sohn
The electrochemical behavior of Ag with Li was investigated with various particle sizes and under different current densities. When tested at a current of
, the electrochemical behavior of a nano-Ag electrode showed a highly reversible reaction with Li, with the first discharge and charge capacities being 1158 and
, respectively. The electrochemical reaction mechanism of Ag alloying/dealloying with Li was revealed by ex situ X-ray diffraction analyses combined with a differential capacity plot of the nano-Ag electrode.
A176
Xue-Bin Zhu, Shu-Lei Chou, Lin Wang, Qi Li, Dong-Qi Shi, Jia-Zhao Wang, Zhi-Xin Chen, Yu-Ping Sun, Hua-Kun Liu and Shi-Xue Dou
A181
Sung Woo Oh, Seung-Taek Myung, Hyun Joo Bang, Chong Seung Yoon, Khalil Amine and Yang-Kook Sun
A186
Gregorio F. Ortiz, Ilie Hanzu, Philippe Knauth, Pedro Lavela, José L. Tirado and Thierry Djenizian
A190
Sukeun Yoon and Arumugam Manthiram
A194
Masahiro Suguro, Shigeyuki Iwasa and Kentaro Nakahara
A copolymerized poly(4-vinyloxy-2,2,6,6-tetramethylpiperidine-
-oxyl) (PTVE) was synthesized by cationic polymerization of a vinyl monomer bearing a 2,2,6,6-tetramethylpiperidine-
-oxyl (TEMPO) radical and an ethylene oxide or tri(ethylene oxide). The charge/discharge properties of copolymerized PTVE improved with the length of the ethylene oxide chain, and high rate and high power properties of the PTVE synthesized by copolymerization with tri(ethylene oxide) were much better than those of the PTVE homopolymer. Electrochemical measurements showed that the ionic conductivity of the polymer synthesized by copolymerization with tri(ethylene oxide) was higher than that of the PTVE homopolymer.
Fuel Cells and Energy Conversion
B119
A. Masao, S. Noda, F. Takasaki, K. Ito and K. Sasaki
B123
Dong-Ha Lim, Woo-Jin Lee, Nathan L. Macy and William H. Smyrl
B126
Sang-Kun Lee, Kohei Ito, Toshihiro Ohshima, Shiun Noda and Kazunari Sasaki
The temperature distribution across a proton exchange membrane fuel cell was measured by inserting micro-thermocouples between layers such as a gas diffusion layer and membrane electrode assembly. Under steady-state operation, the cathode catalyst layer had the maximum temperature. The activation overpotential at the cathode catalyst layer served as the main heat source, resulting in the maximum temperature at the cathode catalyst layer. The temperature at the cathode catalyst layer just after the load current was interrupted had the minimum temperature. This is thought to be caused by water evaporation from the cathode catalyst layer, where liquid water accumulates during operation.
B131
Massimiliano Cimenti, Mickey Tam and Jürgen Stumper
A capacitive arc with a peak frequency at 1–10 kHz is observed during impedance studies on proton exchange membrane (PEM) fuel cells when a shunt resistor is used for measuring the current. A few studies have reported this feature, but its cause has not been identified yet. In this work, correlations between the high frequency arc and the experimental setup are analyzed. Experimental results show that the high frequency arc is likely an experimental artifact caused by neglecting the frequency dependence of the shunt resistor. Methods to avoid this type of distortion and a simple correction procedure are presented.
B135
Keiji Yashiro, Takashi Nakamura, Maya Sase, Florian Hermes, Kazuhisa Sato, Tatsuya Kawada and Junichiro Mizusaki
B138
Yannick Garsany, Benjamin D. Gould, Olga A. Baturina and Karen E. Swider-Lyons
Electrochemical/Chemical Deposition and Etching
D65
Yanqing Lai, Fangyang Liu, Sanshuang Kuang, Jun Liu, Zhian Zhang, Jie Li and Yexiang Liu
D68
Takahiro Ishizaki, Yoshitake Masuda and Naobumi Saito
A composite film composed of crystalline
and
was successfully deposited on magnesium alloy AZ31 from a liquid phase through a single-step process. The film had a thickness of ca. 370 nm and was composed of aggregations of nanoparticles whose diameters were in the range of 50–100 nm. During the corrosion tests, the coated AZ31 substrate showed a higher corrosive resistance than the uncoated AZ31. Potentiodynamic polarization curve measurements revealed that a clear passive region approaching ca. 280 mV could be observed on the curve of the coated AZ31 substrate. The formation and corrosion mechanism of the coated AZ31 substrate has also been discussed.
D72
Tsutomu Shinagawa, Kuniaki Murase and Masanobu Izaki
Physical and Analytical Electrochemistry
F21
S. Devaraj and N. Munichandraiah
F26
Daria Sokic-Lazic and Shelley D. Minteer
Most enzymatic biofuel cells contain bioanodes with single enzymes to partially oxidize biofuels. This is ideal for implantable devices, but two-electron oxidation of fuels limits energy density for portable power applications. This article details the development of enzymatic bioanodes for complete oxidation of pyruvate, where the bioanode contains the enzymes of the Kreb’s cycle, therefore maximizing the energy density. Although pyruvate has not been employed as a fuel for enzymatic biofuel cells in the literature, it has been employed as a fuel for mitochondrial biofuel cells. In this article, we observe 4.6-fold power density increases using individual Kreb’s cycle enzymes compared to the intact mitochondria.
Dielectric Science and Materials
G47
Vadim Sh. Yalishev, Shavkat U. Yuldashev, Yeon Soo Kim and Bae Ho Park
Reproducible resistance switching behaviors induced by the external voltage were investigated in anodic oxide alumina (AOA) thin films. Electric-transport measurements showed that a low resistance state in the Ag/AOA/Al structures might be caused by the formation of the conductive filaments. Switching to a high resistance state occurred due to the rupture of these filaments. Change in the photoluminescence properties of the AOA films depending on the resistance states was observed.
G50
Qian Tao, Gregory Jursich, Prodyut Majumder, Manish Singh, Weronika Walkosz, Peter Gu, Robert Klie and Christos Takoudis
G54
Yuan-Chang Liang
This study investigates the correlation between the microstructure and the physical properties of transparent
(BST) thin films with thicknesses of 90–220 nm on the transparent conductive glass. The dielectric constant and tunability of BST films increase with thickness, as attributed to a comparatively larger grain size and a smaller tensile thermal in-plane strain in the thicker film. A BST film with an optimal thickness of 180 nm has a high tunability/loss tangent value of 34.4 and an optical transparency of over 70%.
Semiconductor Devices, Materials, and Processing
H315
Ray-Ming Lin, Yi-Lun Chou, Wan-Ching Tseng, Chia-Lung Tsai, Jen-Chih Li and Meng-Chyi Wu
In this study, we investigated the thermal stability of Ni/Ag-based alloy contacts on p-type GaN. We observed the morphology of aggregated Ag for the Ni/Ag bilayer on p-type GaN after annealing it at
in an
ambient. To improve the thermal stability, we deposited a Ni/Ag/Au trilayer onto p-type GaN. In this case, Ag aggregation was retarded after thermal annealing, and the specific contact resistance exhibited improved stability. Furthermore, because strong interdiffusion of the Au and Ag layers leads to poor reflectance, we added a diffusion barrier layer into the system; i.e., we deposited Ni/Ag/Ti/Au onto p-type GaN, with the Ti layer playing the role of the diffusion barrier. After annealing, the contact exhibited diminished Ag aggregation and a lower level of interdiffusion of the Au and Ag layers. We investigated the effect of the annealing time (at
in an
ambient) on the properties of the Ni/Ag (1/150 nm), Ni/Ag/Au (1/150/150 nm), and Ni/Ag/Ti/Au (1/150/500/150 nm) layers, namely, their values of specific contact resistance, determined using a modified transmission line model, and reflectance at 465 nm. According to analyses by using scanning electron microscopy and secondary-ion mass spectrometry, we determined that the aggregation of Ag and the interdiffusion of Au and Ag within the Ni/Ag/Ti/Au construct were both minimized with the presence of the Ti layer, thereby improving the thermal stability of the contact on the p-type GaN.
H319
Il-Suk Kang, Sung-Hun Yu, Hyun-Sang Seo, Jeong-Hun Kim, Jun-Mo Yang, Wook-Jung Hwang and Chi Won Ahn
H322
Hwan Hee Jeong, Sang Youl Lee, June-O Song, Kwang Ki Choi, Seok-Hun Lee, Hee Seok Choi, Tchang-Hun Oh, Yong-Hyun Lee and Tae-Yeon Seong
H325
Soon-Won Jung, Sung-Min Yoon, Seung-Youl Kang, Kyu-Jeong Choi, Woong-Chul Shin and Byoung-Gon Yu
H329
Shuyu Zhang, Rongqing Liang, Qiongrong Ou, Xiaojing Wu, Meifu Jiang, Zongfu Nie, Feng Liu, Xijiang Chang, Yipeng Wang, Jilong Du et al
H333
S. Prucnal, L. Rebohle, A. Kanjilal, H. Krzyzanowska and W. Skorupa
H336
Young Hwan Hwang, Jun Hyuck Jeon, Seok-Jun Seo and Byeong-Soo Bae
H340
Min Cheol Kang, Yung Jun Kim and Jae Jeong Kim
An Ag capping layer as a metal barrier was proposed to hinder the oxide formation of Cu, which is exposed after chemical mechanical polishing (CMP). To simplify the process step, the in situ formation of the Ag barrier during the Cu CMP process was investigated using a displacement reaction at either the second step of Cu CMP or the buffing step. The Ag capping layer effectively disturbed the contact between oxygen and Cu, which led to preventing Cu oxidation. Moreover, through the capping formation at the buffing step, the depth of dishing was diminished to about 20 nm regardless of the linewidth.
H344
Xin Ji, Yuan-Wei Dong, Zhong-Qi Huo and Wei Xu
H348
Hyun-Sik Seo, Jong-Uk Bae, Dae-Hwan Kim, YuJin Park, Chang-Dong Kim, In Byeong Kang, In-Jae Chung, Ji-Hyuk Choi and Jae-Min Myoung
Sensors and Displays: Principles, Materials, and Processing
J73
Shinya Teranishi, Kyohei Kondo, Masakazu Nishida, Wataru Kanematsu and Takashi Hibino
J77
Cheng Liao and YewChung Sermon Wu
A periodic n-bowl mirror structure was introduced into light-emitting diodes with roughened p-GaN surface (RP-LED) by wafer bonding and laser lift-off technology. The performance of these n-bowl mirror light-emitting diodes (NBM-LEDs) was better than that of RP-LED. Besides, the light intensity and the output power of NBM-LEDs were increased with the decrease in n-bowl dimension. The view angle was decreased with the diameter of the n-bowl.
J80
Jin-A Jeong, Han-Ki Kim and Seok-In Na
We report on the characteristics of an amorphous indium zinc tin oxide (a-IZTO) multicomponent electrode cosputtered by linear facing target sputtering (LFTS) using indium tin oxide (ITO) and indium zinc oxide targets for bulk heterojunction organic solar cells (OSCs). Without substrate heating or postannealing, the a-IZTO electrode exhibited a low sheet resistance of
, a high average optical transmittance of 88.1% at a wavelength of 500 nm, and a high work function of 5.22 eV. In addition, the a-IZTO electrode with a root-mean-square (rms) roughness of 0.35 nm shows a much smoother surface than the crystalline ITO electrode (rms roughness of 1.25 nm), due to the absence of bombardment of energetic particles on the IZTO electrode during the cosputtering process. Moreover, the OSC with the a-IZTO anode showed a comparable open-circuit voltage (0.56 V), short-circuit current
, fill factor (68.1%), and power conversion efficiency (3.50%) to an OSC with a commercial crystalline ITO electrode. This indicates that the LFTS-grown a-IZTO electrode is a visible alternative to crystalline ITO electrodes for low cost OSCs, eliminating the need for the annealing or substrate heating step generally required for preparing high quality anode electrodes.
J83
Woo-Sung Cho, Yang Doo Lee, Yong Churl Kim, Yoon Chul Son, Jeong Na Heo, In Taek Han, Jung-Ho Park and Byeong-Kwon Ju
Carbon nanotubes (CNTs) were effectively dispersed and functionalized by being wrapped with RNA. The RNA–CNT hybrids attached strongly to an indium tin oxide (ITO) glass substrate and formed a uniform film, making it possible to use field emitters for field emission applications. An electron field emission cathode was fabricated with a spray method using these RNA–CNT hybrids. Well-defined RNA–CNT patterns were obtained on the ITO glass substrate. The cathode showed a uniform emission pattern across the entire surface and also exhibited a high current density. The RNA–CNT hybrids compared favorably to other factionalized CNTs for use in the spray method.
J87
Jing Gou, Yuhua Wang and Haiyan Jiao
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K59
Il Seo, Chang-Woo Kwon, Hyun Ho Lee, Yong-Sang Kim, Ki-Bum Kim and Tae-Sik Yoon
K63
Jaehyun Moon, Su-Jae Lee, Jin-Ah Park and Taehyoung Zyung
We used an electrospinning method to produce ZnO nanofibers for CO sensing. ZnO nanofibers were electrospun from a solution containing poly(4-vinyl phenol) (PVP) and Zn acetate. The calcination process of the ZnO/PVP composite nanofibers brought forth polycrystalline würtzite ZnO nanofibers with diameters of 30–70 nm. Regarding the applications of the ZnO nanofibers, their CO gas-sensing responses were evaluated in a concentration range of 10–25 ppm. The resistances of the ZnO nanofibers were observed to decrease upon exposure to CO. This is attributed to the reducing nature of CO, which reacts with adsorbate
to release an extra electron.
Miscellaneous
S13
Seung-Wan Song, Sung-Jin Hong, Ho Young Park, Young Chang Lim and Ki Chang Lee