Batteries and Energy Storage
A199
Haibo Wang, Kelong Huang, Yuqun Zeng, Fenggang Zhao and Liquan Chen
The reasons for capacity fading of an
lithium-ion cell based on structure and dissolution of transition metals were investigated. X-ray diffraction and inductively coupled plasma results showed that the properties of the anode have an impact on the cycle life of the cell. To stabilize the cycling capacity of the anode, and thus improve the cycle life of the cell, coating with a conductive polyaniline on the surface of the anode was proposed. Cycle tests revealed that the stability of the lithium-ion cell with surface coated anode was greatly improved.
A204
J. Wang, S. H. Ng, Sau Yen Chew, D. Wexler, G. X. Wang and H. K. Liu
A208
Zhumabay Bakenov, Masanobu Nakayama and Masataka Wakihara
A212
H. Groult, T. Nakajima, A. Tressaud, S. Shibata, E. Durand, L. Perrigaud and F. Warmont
A216
Yong Min Lee, Jeong Eun Seo, Young-Gi Lee, Sang Hyo Lee, Kuk Young Cho and Jung-Ki Park
A220
J. T. Vaughey, J. Owejan and M. M. Thackeray
A225
Wonjoo Lee, R. S. Mane, V. V. Todkar, Sangjin Lee, Olga Egorova, Won-Seok Chae and Sung-Hwan Han
A228
A. Manthiram and W. Choi
Fuel Cells and Energy Conversion
B135
Hideto Kurokawa, Tal Z. Sholklapper, Craig P. Jacobson, Lutgard C. De Jonghe and Steven J. Visco
B139
Jingwang Yan, Makiko Enoki, Hiroshige Matsumoto and Tatsumi Ishihara
B142
Yanghua Tang, Jianlu Zhang, Chaojie Song and Jiujun Zhang
B147
Odysseas Paschos, Seth L. Knupp, Pyoungho Choi, Jeremy Snyder, Steve J. Buelte, Nazarali Merchant, Zhigang Qi and Pradeep Haldar
We examined the effect of polytetrafluoroethylene (PTFE) content and annealing temperature on oxygen reduction reaction (ORR) in phosphoric acid for a series of Pt/carbon nanotube (CNT) electrodes. When PTFE is added, PTFE particles cover the electrodes, influencing the active Pt surface area, the adsorption of phosphate species on the Pt surface and mass transport of reactants to the surface. The performance of the Pt/CNT showed maximum at 20 and 25% PTFE content for annealing temperatures of 337 and 350°C, respectively. Performance was further improved by mixing Pt/CNT with
. This may be explained by improved accessibility of reactants to/from the interface.
B150
Lajos Gancs, Brian Nicholas Hult, Nazih Hakim and Sanjeev Mukerjee
B155
D. P. Wilkinson, M. Blanco, H. Zhao, J. Wu and H. Wang
Adequate reactant gas distribution and water management are critical parameters for a fuel cell stack to perform properly and avoid certain failure modes. In this study, an approach is used in which the cathode flow field active area is changed with changing operating conditions. This approach maintains high and stable performance in the fuel cell system without significantly increasing the parasitic load. Such a dynamic flow field is particularly beneficial for applications with a wide range of operating conditions.
Electrochemical/Chemical Deposition and Etching
D89
Xin Sun, Qiang Lu, Hideki Takeuchi, Sriram Balasubramanian and Tsu-Jae King Liu
Argon-ion implantation can be used to selectively and dramatically enhance the etch rate of a silicon dioxide film down to a precise depth, to allow for improved control of etch depth in a timed oxide etch process. An empirical model based on damage concentration, fit to experimental data, is used to explain the correlation between the implantation conditions (dose, energy) and the etch-rate enhancement parameters. The model is shown to yield predictions of the etch rate enhancement consistent with the existing model based on nuclear deposited energy. The depth of etch-rate enhancement is determined primarily by the implant energy, whereas the etch-rate enhancement factor is controlled by the implant dose. Enhancement factors close to five were achieved with moderate-dose 
implantation. Lower ion-implantation energy results in sharper transition between the etch-rate enhanced and the unaffected oxide region. This technique can be used to improve process uniformity in fabrication of three-dimensional semiconductor device structures such as bulk-Si FinFETs, for reduced variations in circuit performance.
D92
Tokihiko Yokoshima, Yasuhiro Yamaji, Hirotaka Oosato, Yuichiro Tamura, Katsuya Kikuchi, Hiroshi Nakagawa and Masahiro Aoyagi
Dielectric Science and Materials
G63
K. Sidi Ali Cherif, S. Kordic, J. Farkas and S. Szunerits
Semiconductor Devices, Materials, and Processing
H243
S. Armini, C. M. Whelan, M. Moinpour and K. Maex
H248
Longcheng Wang and Meng Tao
The conduction type (n- or p-type) of electrochemically deposited cuprous oxide
can be controlled by solution pH. It was found that cuprous oxides deposited at solution pH below 7.5 are n-type semiconductors, while cuprous oxides deposited at a solution pH above 9.0 are p-type semiconductors. A two-step process was adopted to deposit p-type and n-type cuprous oxides in sequence for the formation of a p-n homojunction in cuprous oxide. Photocurrent and current-voltage measurements demonstrate the successful formation of a p-n homojunction of cuprous oxide.
H251
Daniel C. S. Bien, Michael F. Bain, Yee Hooi Low, Neil S. J. Mitchell, Mervyn B. Armstrong and Harold S. Gamble
We have demonstrated a self-aligned process to fabricate organized iron nanowires on a planarized surface with wire dimensions down to
. Polishing was used to expose an alternating silicon silicon dioxide edge and a dual selective metal deposition process produced the nanowires. The initial selective deposition produced a tungsten layer on the exposed polysilicon regions. The discovery that selective chemical vapor deposition of iron from
precursor on dielectric surfaces over tungsten surfaces is the key factor that enables the self-alignment of the iron nanowires. Dimensions of the wires are determined by the thickness of the thermal oxide.
H254
Hyun-Gi Hong, June-O Song, Hyunseok Na, Hyunsoo Kim, Kyoung-Kook Kim and Tae-Yeon Seong
H257
Donovan Lee, Thomas Seidel, Jeremie Dalton and Tsu-Jae King Liu
Atomic layer deposition (ALD) is demonstrated to be effective for filling gaps as small as
and aspect ratios greater than 10 with no void defects. Thus, it is a promising technique to enable the fabrication of complementary metal oxide semiconductor (CMOS) transistors using a “gate-dielectric-last” process to minimize thermal exposure of the high-κ gate dielectric, in order to avoid issues such as gate Fermi-level pinning and increased leakage current density associated with oxygen vacancy formation and crystallization.
H260
Ren Wei and Chi Dongzhi
H264
S. Boninelli, F. Cristiano, W. Lerch, S. Paul and N. E.B. Cowern
H267
Wantae Lim, Yu-Lin Wang, F. Ren, D. P. Norton, I. I. Kravchenko, J. M. Zavada and S. J. Pearton
H270
June O Song, Kyung-Kook Kim, Hyunsoo Kim, Hyun-Gi Hong, Hyeonseok Na and Tae-Yeon Seong
H273
Cheng-Tsung Lee, Wang Yueh, Jeanette Roberts and Clifford L. Henderson
A method which utilizes experimental measurement and modeling of photoacid-catalyzed deprotection rates obtained via Fourier transform infrared spectroscopy has been developed for determining photoacid generator (PAG) photoreaction rate constants (i.e., Dill C parameters) in protected polymer matrices. Numerical modeling of deprotection rates as a function of exposure dose and postexposure bake time is used to determine the Dill C parameters for the PAG in the actual resist matrix polymer of interest. This protocol is shown to be a fast, nondestructive, and material-saving technique that can permit measurement of Dill C parameters in reactive polymer matrixes.
H278
Satoshi Kamiyama, Takayoshi Miura and Yasuo Nara
H281
P. Zhou, Y. C. Shin, B. J. Choi, S. Choi, C. S. Hwang, Y. Y. Lin, H. B. Lv, X. J. Yan, T. A. Tang, L. Y. Chen et al
H284
Nguyen Mai Phuong, Nak-Jin Seong, Jun-Ku Ahn, Eui-Tae Kim, Ji-Hong Lee, Geun Hong Kim and Soon-Gil Yoon
Sensors and Displays: Principles, Materials, and Processing
J101
Yih-Ming Liu, Yuh Sung, Yann-Cheng Chen, Chuan-Ting Lin, Yu-Hsien Chou and Ming-Der Ger
A method to fabricate good carbon nanotube (CNT) field emitters using electroless codeposition and CNT purification techniques was developed. Multiwalled CNTs (MWNTs) were codeposited with Ni to form a composite layer acting as the emitter. This composite layer is uniform in thickness and the MWNTs distributed in Ni matrix show a strong adhesion to the substrate. To ensure the emitting quality and good dispersion of MWNTs in the composite, heat annealing and acid immersion process were employed. The composite film shows good emission uniformity and the current density of
was obtained at about
.
J105
Tse-Heng Chou, Yean-Kuen Fang, Che-Yun Yang, Yen-Ting Chiang, Jin-Shu Shie and Chia-Chen Chien
J108
Ji-Man Cho, Kyoung Soo Kim, Sengdo An, Sang-Yong Lee and Soo-Won Kim
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K39
Sung Hyun Kim, Jyongsik Jang, Ji Hwan Yoon and Jun Yeob Lee
Interdisciplinary Topics
P23
Chien-Neng Liao, Ching-Hua Lee and Wen-Jin Chen