Batteries and Energy Storage
A1785
Sami Oukassi, Cédric Giroud-Garampon, Séverine Poncet and Raphaël Salot
In this work we developed flexible rechargeable thin film lithium ion batteries based on all-solid-state materials. The flexible batteries were fabricated using low temperature sequential physical vapor deposition techniques. A thin film battery (TFB) architecture consisting of Ti/V2O5/LiPON/Li/encapsulation multilayer was deposited on flexible polyimide substrate. To the best of our knowledge, the obtained TFBs are among the thinnest reported with an overall thickness of 50 μm including substrate, active layers and encapsulation stack. The fabricated TFBs delivered discharge capacity as high as 0.15 mAh (1.5 cm² of cathode area) upon galvanostatic cycling at 30 μA.cm−2 within 3.8–1.5 V voltage range. The capacity decreased during cycling with an average fading rate of 0.25% over 100 cycles. Electrochemical impedance spectroscopy (PEIS) measurements and modeling analysis revealed an increase of the internal resistance during cycling. Furthermore, it was shown that the internal resistance increase was induced by a progressive decrease of the electrolyte/electrodes contact area. TFBs having the same architecture and cell design were fabricated on two substrates: a flexible polyimide foil and a rigid silicon wafer. Electrochemical characterization showed a clear influence of substrate type on TFBs discharge capacity and internal resistance variations during cycling, the results are discussed within this paper
A1792
The following article is Free article
Pierrot S. Attidekou, Chen Wang, Matthew Armstrong, Simon M. Lambert and Paul A. Christensen
This paper presents a new technique to determine the online capacity of a lithium ion battery for Electric Vehicle (EV) applications. A mixed calendar and cycling profile is defined and applied to a high power- density 16Ah pouch type battery. Whilst the capacity loss due to cycling is irreversible, the apparent capacity loss due relaxation/self-discharge is found to be pseudo-reversible. The characteristic voltage drop during relaxation is studied in detail, and shown to exhibit behavior which can be modelled using a dynamic time constant approach. Applying this technique, an excellent fit is obtained between the actual and model predicted relaxation curves. The results are of significant practical importance, particularly in the field of lifetime prediction of Li-Ion batteries.
A1802
Hao Liu, Haodong Liu, Saul H. Lapidus, Y. Shirley Meng, Peter J. Chupas and Karena W. Chapman
Lithium transition metal oxides are an important class of electrode materials for lithium-ion batteries. Binary or ternary (transition) metal doping brings about new opportunities to improve the electrode's performance and often leads to more complex stoichiometries and atomic structures than the archetypal LiCoO2. Rietveld structural analyses of X-ray and neutron diffraction data is a widely-used approach for structural characterization of crystalline materials. However, different structural models and refinement approaches can lead to differing results, and some parameters can be difficult to quantify due to the inherent limitations of the data. Here, through the example of LiNi0.8Co0.15Al0.05O2 (NCA), we demonstrated the sensitivity of various structural parameters in Rietveld structural analysis to different refinement approaches and structural models, and proposed an approach to reduce refinement uncertainties due to the inexact X-ray scattering factors of the constituent atoms within the lattice. This refinement approach was implemented for electrochemically-cycled NCA samples and yielded accurate structural parameters using only X-ray diffraction data. The present work provides the best practices for performing structural refinement of lithium transition metal oxides.
A1812
The following article is Open access
Lucas Lodovico, Alberto Varzi and Stefano Passerini
In this work, the stability of ether-based electrolytes for Li-S batteries is investigated with particular regard to the effect of dissolved oxygen. Specifically, the performance of two different electrolyte solvents, i.e., 1,2-dimethoxyethane and its mixture with 1,3-dioxolane (DME:DOL, 1:1 v/v), is characterized in cells assembled in dry air environment, which would substantially lower production costs with respect to inert atmosphere (Ar). Although stability of all the components would suggest that Li-S batteries built in both the environments should behave similarly, it is found that cells containing the DME:DOL-based electrolyte are rather unstable in the presence of O2 in contrast to those employing DME-based electrolyte, which show a relatively good performance. The different sensitivity toward O2 of these electrolytes is associated to the ring-opening reaction of DOL, which happens to a greater extent when O2 is present, but occurs also in its absence. Based on these results a mechanism for electrolyte degradation in Li-S cells, and its reaction with dissolved polysulfides is proposed, which rationally explain for the first time the behavior already reported in literature for these kind of batteries. These findings are also relevant to the field of Li-O2 batteries, where these ether-based electrolytes are also used.
A1820
Hua Zhu, Min Li, Dihua Wang, Shoubin Zhou and Chuang Peng
Advances in multi-electron transfer materials and architectured electrodes are two important strategies for innovations in electrochemical energy storage. We herein report the attainment of both by interfacial electrodeposition of freestanding PPY-PEDOT copolymer films. The composition of the copolymer is verified by FTIR and XPS spectra and the dispersion of PPY and PEDOT is studied by EDX mapping. SEM images show the film has an open porous 3D network microstructure. Electrochemical characterizations show that the copolymer film is an excellent supercapacitor electrode material with high specific capacitance, good power capability and cycle performance. The multi-electron transfer nature of the copolymer, the copolymerization synergistic effects and the unique microstructure are responsible for the improved charge-discharge performances.
A1826
The following article is Open access
Guangyu Liu and Wei Lu
We present a model that enables simulations of concurrent coupled lithium dendrite growth, SEI formation and growth on the dendrite surface, dendrite penetration of the SEI layer, and SEI regrowth. The concept of SEI coverage density is introduced, which is conceptually similar to SEI thickness but broader. SEI and dendrite growth interacts with each other by evolving dendrite morphology, stretching of SEI by the dendrite surface, and the effect of evolving SEI thickness (coverage density) on lithium deposition reaction. The model shows that even under low current density, small protrusions on lithium surface can still grow into dendrites by penetrating SEI and causing inhomogeneous electrical resistance on dendrite surface. We find that dendrite growth shows two distinct stages: fast acceleration during SEI penetration, and stable growth after reaching an equilibrium SEI thickness at the dendrite tip. Under low current density, increasing current scales up the growth rate of dendrite without much shape change. High current density causes dendrite morphology to change significantly, forming a needle shape. We show that local SEI defects/inhomogeneity can induce dendrite formation and growth. Our study suggests that flat lithium surface, uniform SEI layer, and low SEI resistivity are important to reduce dendrite formation.
A1834
Long Chen, Yongchang Liu and Li-Zhen Fan
Safety, energy density and cycling life are believed to the most three urgent concerns to develop next-generation high-performance lithium ion batteries. Lithium metal anode is attractive owing to the extremely high theoretical specific capacity and the lowest negative electrochemical potential. However, the use of metallic lithium anode has been limited by the poor interface stability with the electrolyte along with the occurrence of dendrite growth. Here, we report a self-standing flexible composite polymer electrolyte (CPE) incorporated with organic robust cage-type cucurbit[6]uril (CB[6]) prepared by solvent-free hot-pressing method. Poly(ethylene oxide)-Lithium bis(trifluoromethanesulfonyl)imide with 35 wt% CB[6] composite electrolyte exhibits a wide electrochemical window at 55°C (4.7 V vs. Li+/Li) and high thermal stability (380°C). The interface stability with lithium metal anode is significantly enhanced by the addition of CB[6]. At 0.5 C rate under operation temperature of 55°C, the LiFePO4|CPE|Li battery demonstrates excellent cycling performance with high capacity retention of 99.8% at 100th cycle and 86.5% at 200th cycle, which indicates that such CPE membranes are able to present stable electrode/electrolyte interface and inhibit lithium dendrite growth for achieving high-safety all-solid-state batteries.
A1841
Masanobu Chiku, Shota Matsumura, Hiroki Takeda, Eiji Higuchi and Hiroshi Inoue
Aluminum bis(trifluoromethanesulfonyl)imide (Al(TFSI)3) was synthesized by a simple substitution reaction and investigated as the Al3+ source for the electrolyte of a rechargeable Al battery. The electrochemical window was extended to 3.6 V with the electrolyte containing Al(TFSI)3 in AN, whereas it was ∼2.5 V with the conventional electrolyte for the Al rechargeable battery. A reversible electrochemical Al deposition/dissolution reaction was observed on a Mo plate electrode with small overpotential less than 0.5 V. NMR and Raman spectra identified the main Al species in the electrolyte as Al(TFSI−)x(AN)6-x3-x (x = 1 ∼ 6).
A1845
Youliang Cheng, Qingling Zhang, Changqing Fang and Shaohua Guo
Carbon nanotubes (CNTs) have been successfully grown on the surfaces of mesocarbon microbeads (MCMB) via a chemical vapor deposition (CVD) method by using iron particles as the catalyst. The morphologies of the hybrids were modulated by controlling the ratio (r) of H2 to C2H2. The obtained CNTs are uniform with an average diameter of 20 nm when r = 2 at 750°C. The specific surface area of such MCMB-CNTs-2 is 34.5 m2·g−1, and the specific capacitance is 319 F·g−1 at the current density of 1 A·g−1. More importantly, MCMB-CNTs-2 exhibits extraordinary cycling life stability (the retention is 88.4% after 5000 cycles), despite some CNTs may break off from MCMB surface after cycles. We attribute the improvement of electrochemical properties to the mesoporous structure and excellent electrical conductivity of the hybrids with low specific surface area. Our study indicates that the MCMB/CNTs hybrids are promising candidates for the electrode materials of supercapacitors.
A1852
Qiming Chen, Rong Xu, Zitao He, Kejie Zhao and Liang Pan
Here we demonstrate the use of projection stereo-micro-lithography as a low-cost and high-throughput method to fabricate three dimensional (3D) microbattery. An Ultraviolet (UV)-curable Poly (ethylene glycol) (PEG)-base gel polymer electrolyte (GPE) is first created. The GPE is then used as a resin for micro-stereolithography in order to build a 3D architecture of battery's electrolyte. Active materials, LiFePO4 (LFP) and Li4Ti5O12 (LTO), are mixed with carbon black and the GPE resin, which is then flown into the 3D structure. Aluminum (Al) foil is cut and inserted as a current collector. The GPE is characterized and the microbattery is performed a cycling test. Results show a feasibility of microbattery fabrication using projection micro-stereolithography.
A1858
Paul T. Coman, Stefan Mátéfi-Tempfli, Christian T. Veje and Ralph E. White
This paper presents a mathematical model developed for predicting the temperature-pressure behavior and gas generation inside 18650 LCO/Graphite cells with a DMC (Dimethyl Carbonate) electrolyte. The cell was modeled using oven heating conditions, and the analysis was done at time intervals around the venting event. The paper also presents the thermodynamic property table for DMC, as extracted from different resources and calculated using various assumptions. The model was developed by deriving the energy balance for an unsteady-flow control volume and applying the isentropic flow equations corresponding to the venting of gas. The results show that the model fails to predict the pressure measured experimentally when no gas is generated inside. When adding the gas generation due to pre-venting reactions occurring, the model can predict the pressure profile measured experimentally.
A1866
The following article is Open access
M. Härmas, T. Thomberg, T. Romann, A. Jänes and E. Lust
Various electrochemical methods have been applied to establish the electrochemical characteristics of the electrical double layer capacitor consisting of the activated carbon material based electrodes and 1 M triethylmethylammonium tetrafluoroborate solution in acetonitrile and 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid as the electrolytes. Activated carbon material used for the preparation of electrodes has been synthesized from hydrochar prepared via hydrothermal carbonization process of granulated white sugar solution in H2O, followed by activation with ZnCl2 with a mass ratio of 1:4 at the temperature 700°C. High porosity and Brunauer-Emmett-Teller specific surface area (SBET = 2100 m2 g−1), micropore surface area (Smicro = 2080 m2 g−1) and total pore volume (Vtot = 1.05 cm3 g−1) have been achieved for the granulated white sugar derived carbon (GWS carbon) material. Wide region of ideal polarizability (ΔE ≤ 3.0 V), short characteristic relaxation time (0.5 s and 4.0 s), high specific series capacitance (125 F g−1 and 140 F g−1) and high energy density (39 W h kg−1 and 48 W h kg−1) have been calculated for the GWS carbon material in 1 M triethylmethylammonium tetrafluoroborate solution in acetonitrile and 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid, respectively, demonstrating that these systems are very promising for energy storage devices.
A1873
Qiuping Zhao, Yu Zhang, Fengjuan Tang, Jiachen Zhao and Shiyou Li
The finding of appropriate electrolytes and applying them to low-temperature lithium-ion batteries is of special interest. Lithium difluoro (oxalate) borate (LiODFB) and lithium tetrafluorobotate (LiBF4) are promising salts for lithium-ion batteries owing to their unique characteristics. In this work, the electrochemical behaviors of blend salts of LiODFB and LiBF4 with different mole ratio were studied by employment of ethylene carbonate (EC), diethyl carbonate (DEC) and dimethyl sulfite (DMS) as mixed solvents in order to optimize the low-temperature performance for lithium-ion batteries. The results show that the electrolyte system of LiODFB/LiBF4 (1:1, by molar)-EC/DEC/DMS (1:2:1, by volume) is the optimized electrolyte, and the discharge capacity of the electrodes in the optimized electrolyte is 82.5 mAh g−1 at −40°C, maintaining 55.7% of the room temperature capacity and nearly 100% of capacity retention for 50 cycles. The electrolyte exhibits not only excellent film-forming characteristics, but also low impedance of the interface film at low temperature. Especially, the action mechanism of LiODFB, LiBF4 as well as functional solvent on optimization of low-temperature performance is discussed.
A1881
Swatilekha Ghosh, Allumolu Daya Mani, Brij Kishore, Nookala Munichandraiah, Rayavarapu Prasada Rao, Lee Loong Wong, Stefan Adams and Prabeer Barpanda
In the pursuit to develop practical sodium-ion batteries, safe negative insertion (anode) materials are essential. Recently, Na2Ti6O13 has been unveiled by conventional solid-state synthesis as a 0.85 V anode with 1-dimensional Na+ diffusion pathways. Here, an energy-savvy autocombustion synthesis has been successfully implemented to produce the target compound Na2Ti6O13 by restricting the annealing duration within 2 h. This drastic reduction in heat-treatment time involves minimal grain-growth hence forming homogeneous nanostructured particles (∼100 nm). It benchmarks the shortest synthesis of Ti-based anodes for sodium-ion batteries. The current work describes various aspects of autocombustion route. The as-prepared compound delivers near theoretical capacity (ca. 40 mAh g−1) involving a Ti4+/Ti3+ redox potential centered at 0.83 V (vs. Na/Na+) with excellent reversibility. Using both experiment and bond valence site energy (BVSE) modeling, the electrochemical, Na+ diffusion pathways and corresponding energy barriers have been explained.
A1887
Tae Jin Lee, Jeong Beom Lee, Taeho Yoon, Hosang Park, Sunhyung Jurng, Daesoo Kim, Jiwon Jung, Jiyong Soon, Ji Heon Ryu, Kyu Tae Lee et al
Tris(pentafluorophenyl)silane (TPFPS) is examined as a solid electrolyte interphase (SEI)-forming agent for a graphite electrode. The surface film (SEI layer) generated from a conventional carbonate-based electrolyte (TPFPS-free) is so poorly passivating that continued reductive electrolyte decomposition and concomitant film deposition are employed to increase its thickness. Thus, the electrode develops more sluggish kinetics. An electrochemical quartz crystal microbalance (EQCM) study demonstrates that TPFPS is preferentially electroreduced before the organic carbonate solvents on the copper electrode, as predicted from ab initio calculations. Preferential electroreduction of TPFPS over the carbonate-based electrolyte is also observed after first lithiation of the graphite electrode. This gives a more compact and evenly covered SEI layer. The passivating ability of the resulting SEI layer is so high that additional electrolyte decomposition/film deposition is greatly suppressed. Consequently, both Li/graphite half-cell and graphite/LiCoO2 full-cell show higher Coulombic efficiency and better capacity retention in the TPFPS-added electrolyte.
A1893
The following article is Open access
M. P. Klein and J. W. Park
Understanding internal state non-uniformity that occurs across the electrodes in large-format Lithium-ion batteries, and among parallel-connected cells, is a critical part of the cell and battery module design process. Two separate groups of parallel-connected 18650 cells were tested using LiFePO4/C6 (LFP), and LiNiMnCoO2/C6 (NMC) chemistries. Pulse and full-capacity discharges were performed at various States of Charge (SOC), C-rates, average temperatures, and levels of temperature non-uniformity. Current non-uniformity for the pulse testing was always lower for the LFP group compared to the NMC group. The hottest cell in the LFP group produced up to 40% more current than average, while this was up to 80% for NMC. Conversely, under charge depleting conditions the NMC group experienced less current non-uniformity, and in certain cases provided a nearly uniform current distribution in the presence of non-uniform temperature. The results indicate that higher temperature sensitivity in the impedance of a cell will cause larger current non-uniformity under pulse conditions. However, due to the presence of non-uniform SOC for charge depleting, the Open Circuit Voltage (OCV) versus SOC gradient plays a significant role in dictating the current distribution behavior, where steeper OCVs provide a corrective action that minimizes the effect of the non-uniform impedance.
A1907
Sarah L. Guillot, Adrian Peña-Hueso, Monica L. Usrey and Robert J. Hamers
The high flammability and thermal instability of conventional carbonate electrolytes limit the safety and performance of lithium-ion batteries (LIBs) and other electrochemical energy storage devices. Organosilicon solvents have shown promise due to their reduced flammability and greater chemical stability at high temperatures. A series of organosilicon electrolytes with different functional substituents were studied to understand the structural origins of this enhanced stability. The thermal and hydrolytic stability of organosilicon and carbonate solvents with LiPF6 was probed by storage at high temperatures and with added water. Quantitative monitoring of organosilicon and carbonate electrolyte decomposition products over time using NMR spectroscopy revealed mechanisms of degradation and led to the discovery of a key PF5-complex that forms in organosilicon electrolytes to inhibit further salt breakdown. Increased knowledge of specific structural contributions to electrolyte stability informs the development of future electrolyte solvents to enable the safer operation of high-performing lithium-ion batteries.
A1918
Yuying Wang, Juan Du, Hongliang Zhang, Lei Liu, Yifeng Yu, Yue Zhang, Haijun Lv and Aibing Chen
Nitrogen-doped hollow mesoporous carbon spheres (NHMCSs) are synthesized by a one-pot silica-assisted assembly process and applied in supercapacitors. SiO2 spheres act as interior cores, which is crucial to form the hollow structure. 3-Aminophenol/formaldehyde resin and tetraethylorthosilicate (TEOS) cross-link through hydroxyl groups, then together directly deposit and co-assemble with cetyltrimethylammonium bromide via electrostatic interactions leading to an outer carbon-silica shell surrounding the SiO2 spheres. In the preparing process, TEOS not only acts as silica-assisted material and assembles with 3-aminophenol/formaldehyde resin, but also creates more pores to improve the surface area. After carbonization and silica etching, the NHMCSs with spherical morphology, uniform mesoporous, hollow structure, high surface area and nitrogen content are obtained. The nitrogen-doped, hollow and mesoporous structure are conducive to improve the capacitance. As electrode materials, the NHMCSs exhibit a high capacitance (201 F g−1 at 1 A g−1) and a good cycling stability (83.3% after 5000 cycles). These results reveal that NHMCSs can be expected to be promising electrode materials for electrochemical capacitors.
A1924
Long Wang, Yulin Ma, Panpan Wang, Shuaifeng Lou, Xinqun Cheng, Pengjian Zuo, Chunyu Du, Yunzhi Gao and Geping Yin
Tris(2, 2, 2-trifluoroethyl) borate (TTFEB) is evaluated as an effective electrolyte additive for LiNi1/3Co1/3Mn1/3O2 cathode. Galvanostatic charge/discharge tests indicate that the cycling performance and rate capability of LiNi1/3Co1/3Mn1/3O2 cathode are enhanced dramatically with the presence of 0.5 wt% TTFEB in electrolyte, which delivers a high initial discharge capacity of 185.3 mAh g−1 at 0.5 C with high capacity retention of 89.5% after 100 cycles. Moreover, superior discharge capacity of 135.1 mAh g−1 is displayed at high rate of 4 C, while only 73.7 mAh g−1 is delivered for the cell without TTFEB. The effects of TTFEB on the LiNi1/3Co1/3Mn1/3O2 cathode surface are further investigated by EIS, SEM, XRD and XPS. It is found that the enhanced electrochemical performance can mainly be attributed to the alleviation of electrolyte decomposition and prevention of LiNi1/3Co1/3Mn1/3O2 cathode structural deterioration at the high voltage, which is benefited by the formation of the thin and uniform film with lower interfacial impedance on cathode surface with the presence of TTFEB.
A1933
The following article is Open access
Barak Shapira, Izaak Cohen, Eran Avraham and Doron Aurbach
Capacitive mixing is a newly emerging technique for the production of renewable energy from the controlled mixing of river water and seawater. Energy extraction is provided by the potential rise in electrodes held in a fixed charge, as a response to the concentration change. Therefore, electrodes that exhibit high potential variation as a response to concentration change (negative rise for the cation-capturing electrode and vice versa) are highly desirable. In this work, electrodes that can accommodate mostly cations within their porous structure are discussed. In accordance to the modified Donnan (mD) model of the electrical double layer, it is expected that such electrodes will display the highest potential change as a response to concentration change (while being held with a fixed charge). Using appropriate selective activated carbon electrodes, high potential rise, around 50 mV, was observed as a response to concentration change, when the concentration of NaCl solutions was changed from 1M to 10−1 M and from 10−1 M to 10−2 M. Such a capability of potential rise of selective electrodes can serve as a good basis for energy extraction by capacitive mixing.
A1939
Chenhui Yang, Wenxiu Que, Yi Tang, Yapeng Tian and Xingtian Yin
Two-dimensional (2D) transition metal carbides (MXenes) have been recently attracted as promising electrode materials for energy storage applications. Herein, we report a high-capacity supercapacitor material based on nitrogen and sulfur co-doped titanium carbides (NS-Ti3C2), which is prepared by a simple thiourea-assisted carbonization of large-scale Ti3C2 nanosheets. Importantly, results indicate that the 2D Ti3C2 treated with thiourea-assisted carbonization results in change in its microstructure, specific surface area, and mesopores. And, it also has a crucial effect on co-doping content and position of N and S, which can improve the accessibility to active sites. The carbonization treated NS-Ti3C2 nanosheets exhibit a high specific capacitance of 175 F g−1 at 2 mV s−1 in 1 M Li2SO4 electrolyte solution, and a prominent cycling stability (90.1% of the initial capacitance after 5000 cycles). The significant improvement in electrochemical performance of the NS-Ti3C2 can be attributed to larger surface areas and more mesopores, actually, the doping of N and S can enhance the intercalation of ion electrolyte, provide more abundant electrical charge, and thus contribute to the pseudocapacitance. Hence, this new type of nitrogen and sulfur co-doped Ti3C2 could be a promising electrode material for high-performance supercapacitors.
A1946
The following article is Open access
Luxi Shen, Masato Mizutani, Gabriel G. Rodríguez-Calero, Kenneth Hernández-Burgos, Thanh-Tam Truong, Geoffrey W. Coates and Héctor D. Abruña
In an effort to dramatically increase the capacity and electronic conductivity of organic-based redox active materials for electrochemical/electrical energy storage applications, polypyrrole (PPy) has been used as an anchoring backbone to form a family of dimethoxybenzene- (DMB-), bis(methylthio)benzene- (BMTB-), N, N, N’, N’-tetramethylphenylenediamine- (TMPD-), and N, N, N’, N’-tetramethylbenzidine- (TMB-) functionalized redox-active polymers. PPy was deliberately modified to provide an electronically conducting backbone with redox active pendants (RAPs) to enable immobilization (via electropolymerization) of the polymers onto current collectors. The RAPs dramatically increase the capacities of the materials by the reversible exchange of multiple electrons per formula unit. The electropolymerization of the pyrrole-anchored RAP monomers was achieved via cyclic voltammetry. The stability of the electropolymerized films was highly dependent upon the redox potential of the RAPs. The effects of charge density, during the electropolymerization process, were studied by varying the structure of the monomers. By the systematic characterization of the electrochemical properties of the electropolymerized films, the electrochemical behavior of these polymers provides validation of our targeted design to maximize the energy density of organic electrode materials for electrical energy storage applications.
A1952
Qingqing Qin, Xiaodong Du, Chenxi Xu, Shenggen Huang, Weijie Wang, Yong Zhang, Jian Yan, Jiaqin Liu and Yucheng Wu
Mechanical strength is crucial to flexible supercapacitors during their practical usage. In this work, polybenzimidazole with a high tensile strength of ∼100 MPa, an anion (or proton) conducting polymer electrolyte when doped with KOH (or H3PO4), was employed to fabricate highly robust and flexible supercapacitors. The polybenzimidazole film was integrated with activated carbon electrodes coated on graphite paper. These flexible supercapacitors exhibited low equivalent series resistance and good cycling stability of capacitance retention above 90% after 10000 cycles. Under mechanical deformations of bending, twisting, and rolling as well as a repeated bending test, the electrochemical performance of the flexible supercapacitors was well maintained, demonstrating good flexibility. The integration design showed better reliability against mechanical damage. It is an advantage for flexible supercapacitors with high energy density in mass production especially for devices based on KOH doped polybenzimidazole. This work suggests that polybenzimidazole based ion conducting polymer electrolytes are very promising for developing highly robust flexible supercapacitors in future practical applications.
A1958
The following article is Open access
Yoshinori Morita, Shinya Watanabe, Peng Zhang, Hui Wang, Daisuke Mori, Yasuaki Matsuda, Osamu Yamamoto, Yasuo Takeda and Nobuyuki Imanishi
Here we show the feasibility of a novel high energy density battery with a Li anode and a MCl2 (M = Fe, Co, Ni, Cu, and Zn) aqueous cathode separated by a water-stable NASICON-type lithium-ion conducting solid electrolyte of Li1.4Al0.4Ge0.2Ti1.4(PO4)3 (LAGTP). The Li/MCl2 (M = Co, Ni, and Zn) aqueous solution with LiCl cells were successfully charged and discharged. In contrast, the Li/MCl2 (M = Fe and Cu) cells were discharged, but they could not be charged, because FeCl2 and CuCl2 reacted with lithium-ions to produce an insoluble compound. The Li/CoCl2 and Li/NiCl2 cells showed discharge cathode capacities of 326 and 412 mAh g−1 at 60°C and 4.0 m A cm−2, respectively, which correspond to 78 and 100% to the theoretical capacity, respectively. The estimated specific energy densities calculated using the mass of cell components with a 0.1 mm thick LAGTP separator (except the packaging) were 617 and 670 Wh kg−1 for the Li/CoCl2 and Li/NiCl2 cells, respectively, which are approximately two times higher than those for conventional lithium-ion batteries.
A1965
Jin Il Kim, Jinwoo Heo and Jong Hyeok Park
The development of polymer separators for Na+-ion batteries has not been of interest because conventional polyolefin (e.g., polyethylene or polypropylene) separators are not suitable for the solvation of Na+-ion-containing electrolytes. Here, we report a simple surface modification method based on chemical vapor deposition of SiO2 applied to a polyethylene separator for Na+-ion batteries. A thin SiO2 layer is coated uniformly onto a porous polymer separator with the negligibly increased total separator thickness. Improved wetting ability of the SiO2-film-coated polyethylene separators with a polar electrolyte based on ethylene carbonate (EC) and dimethyl carbonate (DMC) solvents is demonstrated, with superior electrochemical performance characteristics, such as initial specific capacity, C-rate and cyclic stability. In addition, the thin SiO2 coating film results in substantially suppressed thermal shrinkage, which may lead to improvements in the thermal and dimensional stability of Na+-ion batteries. Compared to a glass-fiber separator and the conventional PE separator, the metal-oxide-thin-film-coated polyethylene separator will accelerate the development of Na+-ion batteries for various electrochemical energy storage applications.
A1970
Mohammed Al-Yasiri and Jonghyun Park
The flow in a vanadium redox flow battery, which is determined by flow rate and geometry of flow channels, is an important factor in determining battery performance. Therefore, flow rate and flow channel must be carefully designed and controlled to provide smooth supplies of electrolyte to the areas where electrochemical reactions take place. Through a verified three-dimensional electrochemical steady-state model involving fluid motion, it is found that channel height is an important geometric parameter that determines battery performance. We investigate its impact on pressure drop and penetration of the electrolyte into the electrode, and then examine how it ultimately played a role in voltage response, energy efficiency, and battery efficiency. To identify the optimal channel shape, various operating parameters (including flow rate, current, and state of charge) are investigated at different channel heights. Overall, low-height cells are found to have better energy and battery efficiency, and can operate at relatively lower optimal flow rates. There is, however, a trade-off between an improved flow field and pumping loss, depending on geometry and loading conditions. A judicious balance between them would be useful in finding the optimal flow channel geometry and ideal loading conditions for the best performance of flow batteries.
A1983
Altug S. Poyraz, Jianping Huang, Shaobo Cheng, Lijun Wu, Xiao Tong, Yimei Zhu, Amy C. Marschilok, Kenneth J. Takeuchi and Esther S. Takeuchi
α-MnO2 type manganese dioxide is an interesting prospective cathode material for reversible lithium insertion owing to its cation accessible tunnels (0.46 nm × 0.46 nm), high voltage, and low cost. The tunneled structure is synthetically formed by the assistance of cations acting as structure directing agents where the cations may remain in the tunnel. The electrochemistry of this family of materials is strongly dependent on the morphological and physicochemical (i.e. surface area, crystallite size, and average manganese oxidation state) properties as well as tunnel occupancy. In this work, we prepared a set of materials Mn8O16·0.81H2O, K0.81Mn8O16·0.78H2O and Ag1.33Mn8O16·0.95H2O with similar nanorod morphology, crystallite size, surface area, and tunnel water content. This set of samples allowed us to investigate the role of tunnel cations in the electrochemistry of α-MnO2 type manganese dioxide in a lithium based environment while minimizing the effects of the other parameters. The electrochemistry was evaluated using cyclic voltammetry, galvanostatic cycling, rate capability, and galvanostatic intermittent titration type testing. Mn8O16·0.81H2O showed higher loaded voltages, improved capacity retention, and higher specific energy relative to K0.81Mn8O16·0.78H2O and Ag1.33Mn8O16·0.95H2O. After 100 cycles, Mn8O16·0.81H2O delivered ∼200% more capacity than Ag1.33Mn8O16·0.95H2O (64 vs. 129 mAh/g) and ∼35% more capacity than K0.81Mn8O16·0.78H2O (85 vs. 129 mAh/g). Mn8O16·0.81H2O also showed higher effective lithium diffusion coefficients (DLi+) and higher rate capability compared to K0.81Mn8O16·0.78H2O and Ag1.33Mn8O16·0.95H2O suggesting faster Li+ ion diffusion in the absence of large metal tunnel cations.
A1991
Pei Shi, Shaohua Fang, Dong Luo, Li Yang and Shin-ichi Hirano
In this work, a safe electrolyte was formulated by mixing propylene carbonate with 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether, in which fluoroethylene carbonate was used to improve the compatibility of electrolyte with graphite anode. It was found that this electrolyte showed high safety and good wettability to separator and electrodes, and its conductivity reached 5.04 mS cm−1 at 25°C. In particular, this safe electrolyte could well support graphite/LiCo1/3Mn1/3Ni1/3O2 full cells. Its rate and cycle performances at room temperature were close to those of a conventional electrolyte, and better cycle performance at elevated temperature (60°C) was obtained. Moreover, it also showed excellent low-temperature performance, and the cell could even operate at −40°C.
A2000
Yaxin Chen, Liluo Shi, Ang Li, Su Zhang, Mengyao Guo, Xiaohong Chen, Jisheng Zhou and Huaihe Song
Capacity enhancements are sometimes observed when carbon materials, especially porous carbons, are used as lithium-ion batteries anodes. However, the correlative mechanism is unclear now. Here, porous carbon (PC) is used to reveal the mechanism by using a combination of structure analysis and electrochemical calculations. The coexistence of blind pores and closed pores with fractal porous structure is confirmed by N2 sorption and small angle X-ray scattering. When the PC with main pore diameter of 30 nm is used as lithium-ion batteries anode, the specific capacity increases from 700 mAh g−1 (40th cycle) to 1300 mAh g−1 (110th cycle) at a current density of 50 mA g−1. It could be ascribed to the stepwise diffusion of Li atoms inside the pore structure, including the following two effects. (1) The diffusion of solvated Li+ in the blind pores results in the continuous formation of solid electrolyte interface, providing more activated sites on the inside surface; (2) Li atoms diffuse into the inner closed pores via disordered carbon walls to further enhance the reversible capacity. Our finding provides a deep insight on the mechanism of capacity enhancement of porous carbon electrodes, which could benefit the design of advanced electrode materials.
A2007
Shaoqiang Yang, Ruhong Li, Xianyu Cai, Kuiwang Xue, Baofeng Yang, Xinguo Hu and Changsong Dai
In order to improve the electrochemical performance of lead-acid batteries for energy storage, SnSO4 and Sb2O3 were selected as additives to form positive plates. The effects of these additives on the composition and the microstructure of the positive plate were investigated. The content of PbSO4 and hydrated PbO2 in positive active material (PAM) of lead acid batteries have been characterized by chemical analysis and X-ray photoelectron spectroscopy (XPS). Experiment results prove that the contents of hydrated PbO2 gradually decrease with the increase of PbSO4, and the maximum depth-of-discharge (DoD) for electrodes is determined. Through contrastive analysis of different types of electrodes, the relation between the content of hydrated PbO2 and cycle life has been obtained. Using this method, the cycle life of new batteries could be predicted rapidly.
A2012
S. J. Richard Prabakar, Su Cheol Han, Chunguk Park, Ikhe Amol Bhairuba, Michael J. Reece, Kee-Sun Sohn and Myoungho Pyo
For the first time we report that hard-wood (oak) can spontaneously create interconnected channels of μm to nm in diameter during carbonization at an optimized temperature (1100°C). These microstructural features have never been found in other hard-carbons without the use of additives. When compared with sucrose-based hard-carbon (SHC), oak-based hard-carbon (OHC) shows much higher charge-storage capability (ca. 223 vs. 112 mAh·g−1 at 20 mA·g−1) and excellent stability (fading rate of 0.04 vs. 0.08%·cycle−1) as an anode in potassium-ion batteries. The high performance of OHC mainly results from interwoven nanoporous channels, which lead to facile charge transfer and fast K+-diffusion.
A2017
The following article is Open access
Roberto Scipioni, Peter S. Jørgensen, Christopher Graves, Johan Hjelm and Søren H. Jensen
In this work an Equivalent Circuit Model (ECM) is developed and used to model impedance spectra measured on a commercial 26650 LiFePO4/Graphite cylindrical cell. The ECM is based on measurements and modeling of impedance spectra recorded separately on cathode (LiFePO4) and anode (Graphite) samples, harvested from the commercial cell. Modeling of the single-electrode impedance spectra provided information about the electronic and ionic resistance in the porous composite electrodes, as well as the solid state diffusion. Focused Ion Beam (FIB)/Scanning Electron Microscopy (SEM) of anode and cathode samples was used to make 3-D maps of the electrode microstructures and to obtain microstructural data for the ECM. The complementary analysis was crucial for the resolution of the single electrode impedance parameters and the proposal and validation of a new equivalent circuit used to model the full commercial battery impedance.
A2031
Yanqiong Shi, Chaolumen Wu, Lei Li and Jun Yang
A novel polymer electrolyte based on lithiated perfluorinated sulfonic acid ionomer (PFSA-Li) and poly(tetrafluoroethylene) (PTFE) was prepared, and its performance in the Li-O2 batteries was evaluated. In this polymer electrolyte, porous PTFE membrane was used as supporting substrate to provide mechanical strength and dimensional stability, and PFSA-Li ionomer was employed as polymer electrolyte to fill into the pores of the PTFE substrate. After swollen with anhydrous dimethyl sulfoxide solvent, the PFSA-Li/PTFE polymer electrolyte showed a high room temperature ionic conductivity of 1.5 × 10−4 S cm−1 and a high lithium transference number of 0.84. Its use in a lithium-oxygen battery demonstrated excellent compatibility to lithium anode with stable interface property and dendrite-free Li deposition. A good cycling stability over 90 cycles at 1000 mAh g−1 and rate capability up to 2 A g−1 were obtained suggesting a feasible strategy for developing large-scale Li-O2 battery systems toward high energy and high power application with polymer electrolytes.
A2038
The following article is Open access
Selina Liu, Matt Kok, Yongwook Kim, John L. Barton, Fikile R. Brushett and Jeff Gostick
Electrospinning was used to create custom-made fibrous electrode materials for redox flow batteries with targeted structural properties. The aim was to increase the available surface area for electrochemical reaction without diminishing the transport properties of the electrode. Electrospinning conditions were identified that could produce fibers several times larger than those typically yielded by the technique, yet much smaller than in commercially available electrodes. These materials were subsequently carbonized using widely reported protocols. The resultant materials were subjected to a range of characterization tests to confirm that the feasibility of the target material, including surface area, pore and fiber sizes, porosity, conductivity, and permeability. The most promising material to emerge from this selection processes was then tested for electrochemical performance in a flow cell. The produced material performed markedly better than a commercially available material. Further optimizations such as improved consistency in the production and some surface activation treatments could provide significant advancements.
A2049
Kazushi Hayashi, Yuya Wada, Yasutaka Maeda, Tsubasa Suzuki, Hisatoshi Sakamoto, Wai Kian Tan, Go Kawamura, Hiroyuki Muto and Atsunori Matsuda
The electrochemical performance of porously sintered iron-based negative electrodes was examined to assess their suitability for application to high performance alkaline rechargeable batteries. Atomized iron-based powders with and without sulfur were used as raw materials of the electrodes. In order to clarify the discharge-charge mechanism, effects of additives such as K2S, Bi2S3 and LiOH on the electrochemical reaction were also discussed based on the results of cyclic voltammetry in conjunction with changes in the chemical bonds along with the depth from the electrode surface. It was found that the electrochemical performance of the iron electrodes (atomized iron-based powders without sulfur) was improved when K2S was added to the electrolyte of 8 M KOH. The discharge capacity was two times larger than those having the LiOH or Bi2S3 additive in the electrolytes. Furthermore, the discharge curves showed three distinct potential plateaus at about −1.0, −0.9 and −0.7 V vs. Hg/HgO, indicating that oxidation reaction was induced by sulfur additive in the electrolyte. It was revealed by X-ray photoelectron spectroscopy (XPS) analysis that the surface of the iron was uniformly covered with FeS of about 200 nm in thickness in the vicinity of the electrode surface. It is obvious from the XPS spectra that formation of FeS was the primary reaction on the electrode surfaces. Owing to the above-mentioned reaction, the discharge capacity for the negative electrodes fabricated with the sulfur-containing iron-based atomized powders increased with the number of cycles and reached 200 mAhg−1(Fe) at the 15th cycle, and maintained the behavior up to 25 cycles with a Coulombic efficiency of around 100%.
A2056
Ki-Hun Nam, Jeong-Hee Choi and Cheol-Min Park
Sb2Te3 and its amorphous carbon-modified nanocomposite (Sb2Te3–C) are synthesized by simple solid-state synthetic methods, and their potential as anode materials for rechargeable Na-ion batteries (NIBs) is evaluated. Ex situ X-ray diffraction and high-resolution transmission electron microscopy clearly demonstrate the sodiation/desodiation reaction mechanism of the Sb2Te3 and Sb2Te3–C nanocomposite electrodes. In both electrodes, Sb2Te3 is converted into Na3Sb and Na2Te during Na insertion. However, Na3Sb and Na2Te in only the Sb2Te3–C nanocomposite electrode recombine into the original Sb2Te3 phase after full Na extraction. As a consequence of its interesting conversion/recombination reaction during sodiation/desodiation reaction, the Sb2Te3–C nanocomposite electrode exhibits a long cycle life with highly reversible gravimetric and volumetric capacity (373 mAh g−1 and 765 mAh cm−3 over 50 cycles) and fast rate capability (1 C: 391 mAh g−1 and 802 mAh cm−3; 2 C: 377 mAh g−1 and 773 mAh cm−3).
A2065
Sandeep Bhattacharya and Ahmet T. Alpas
Si-Al composite anodes, where micron-sized Si particles were embedded in a ductile Al matrix, were electrochemically cycled in ethylene carbonate (EC)- and propylene carbonate (PC)-based electrolytes vs. Li/Li+. When cycled in PC-based electrolytes, cracks were not formed in Si at a low voltage scan rate of 0.50 mVs−1. However, cracks formed in Si when lithiated in EC-based electrolytes and these cracks were arrested by the surrounding Al-matrix and subsequently closed during de-lithiation. Lithiation at a high scan rate of 5.00 mVs−1 increased the crack formation probability but in PC-based electrolytes, only a few cracks were formed and then closed during de-lithiation. The results suggest that composite Si-Al anodes, which do not pulverize like monolithic Si, could provide durable electrodes for Li-ion batteries–especially if they contain small Si particles (<10 μm) and cycled in a PC-based electrolyte.
A2075
Kyulin Lee, Sangryun Kim, Jesik Park, Sung Hyeon Park, Ali Coskun, Dae Soo Jung, Woosuk Cho and Jang Wook Choi
All-solid-state batteries (ASSBs) are gaining prominence for their ability to overcome the intrinsic drawbacks of conventional liquid-based counterparts, such as electrolyte leakage, flammability, and limited voltage window. Nevertheless, ASSBs have so far been mainly investigated using lab-scale dry mixing processes and therefore suffer from limitation of scalability and agglomeration of active particles in the composite electrodes. Here, we report a systematic investigation on ASSBs fabricated by a solution-based casting process. By screening a wide range of binders and solvents, acrylonitrile butadiene rubber and para-xylene were a suitable binder and solvent, respectively, compatible with sulfide glass-ceramic solid electrolyte. This binder-solvent combination facilitates homogeneous dispersion of the solid electrolyte in the slurry and electrolyte layer, offering high adhesion between electrode materials and comparable lithium ionic conductivity to that of the dry mixing-based counterpart. When solution-based casting processes were adopted for both electrolyte and composite cathode (containing LiNi0.8Co0.1Mn0.1O2) layers, the solution-processed cell exhibits decent performance in rate capability and cyclability due to higher homogeneity of the electrode components, originating from the appropriate combination of solvent and binder.
A2082
The following article is Open access
Taeho Yoon, Navid Chapman, Daniel M. Seo and Brett L. Lucht
Silicon electrodes were cycled with electrolytes containing different salts to investigate the effect of salt on the electrochemical performance and SEI structure. Comparable capacity retention were observed for the 1.2 M LiPF6, LiTFSI and LiClO4 electrolytes in ethylene carbonate (EC):dimethyl carbonate (DEC), 1:1, but severe fading was observed for the 1.2 M LiBF4 electrolyte. The differential capacity plots and EIS analysis reveals that failure of the 1.2 M LiBF4 electrolyte is attributed to large surface resistance and increasing polarization upon cycling. However, when LiBF4 was added as an electrolyte additive (10% LiBF4 and 90% LiPF6), the capacity retention and Coulombic efficiency were improved. The SEI was analyzed by FTIR and XPS for each electrolyte. Both spectroscopic methods suggest that the main components of the SEI are lithium ethylene dicarbonate (LEDC) and Li2CO3 in the 1.2 M LiPF6, LiTFSI and LiClO4 electrolytes, while an inorganic-rich SEI, composed of LiF and borates, was generated for both the 1.2 M LiBF4 electrolyte and the 10% LiBF4 electrolyte. The chemical composition of the SEIs and corresponding electrochemical performance of the Si electrodes were strongly correlated with electrolyte solution structure.
A2089
The following article is Open access
D. J. Xiong, T. Hynes and J. R. Dahn
Different concentrations of LiPF6 (0.3 M–2 M) in ethyl methyl carbonate (EMC) electrolyte and ethylene carbonate (EC)-based electrolyte were studied in LiNi0.4Mn0.4Co0.2O2 (NMC442)/graphite pouch cells. Fresh cells containing 0.3 M LiPF6 in EMC electrolyte showed extremely large charge transfer resistance while those with 0.3 M LiPF6 in EC/EMC electrolyte did not. Impedance spectra taken on symmetric cells and ionic conductivity measurements suggest this difference is due to difficulty in dissociating and desolvating Li+ ions from the EMC-based electrolyte to intercalate into both the electrodes. After elevated temperature storage experiments at 4.5 V, cells with 0.3 M LiPF6 in EC/EMC showed a large increase in positive electrode charge transfer impedance, presumably caused by electrolyte oxidation. With salt concentrations greater than 1 M, charge transfer resistance was much smaller in EMC-based electrolytes and was stable during storage for both electrolyte types. Conductivity and cycle testing measurements suggest that 1.5 M LiPF6 should be used in EC-free EMC-based electrolytes to optimize cell performance.
A2101
The following article is Open access
Daniela Oboroceanu, Nathan Quill, Catherine Lenihan, Deirdre Ní Eidhin, Sergiu P. Albu, Robert P. Lynch and D. Noel Buckley
The stability of typical vanadium flow battery (VFB) catholytes was investigated at temperatures in the range 30–60°C for VV concentrations of 1.4–2.2 mol dm−3 and sulfate concentrations of 3.6–5.4 mol dm−3. In all cases, V2O5 precipitates after an induction time, which decreases with increasing temperature. Plots of the logarithm of induction time versus the inverse of temperature (equivalent to Arrhenius plots) show excellent linearity and all have similar slopes. The logarithm of induction time also increases linearly with sulfate concentration and decreases linearly with VV concentration. The slopes of these plots give values of concentration coefficients βS and βV5 which were used to normalize induction times to reference concentrations of sulfate and VV. An Arrhenius plot of the normalized induction times gives a good straight line, the slope of which yields a value of 1.791 ± 0.020 eV for the activation energy. Combining the Arrhenius equation with the observed variation with sulfate and VV concentrations, an equation was derived for the induction time for any catholyte at any temperature in the range investigated. Although the mechanism of precipitation of VV from catholytes is not yet well understood, a precise activation energy can now be assigned to the induction process.
A2110
The following article is Open access
Zhi-Hui Xie, Zimin Jiang and Xueyuan Zhang
In situ transmission electron microscopy (TEM) electrochemistry with high-resolution characterization of morphology and microstructure is a powerful and practical technique to observe and analyze the lithiation and delithiation process of Li ions in the cathode and anode for comprehensively understanding the performance of Li-ion batteries (LIB), the formation of a solid electrolyte interphase (SEI), and the aging process during the investigation of LIBs. This review mainly focuses on the development and achievements of in situ TEM electrochemical techniques in investigating the mechanism of LIBs in recent years. Three types of in situ TEM electrochemical holders that are used commonly in the characterization of LIBs are presented. A calculation method for quantitative determination of the lithium diffusion coefficient (DLi) in electrodes with in situ TEM electrochemical technique is also mentioned. Finally, the challenges, limitations, and future work for during application of the in situ TEM-electrochemistry technique are further discussed and reviewed from the perspective of morphology, influence of electron radiation on the decomposition of electrolyte, configuration of electrode, and determination of DLi.
A2124
The following article is Open access
Jesse S. Ko, Christopher S. Choi, Bruce Dunn and Jeffrey W. Long
We evaluate a series of nanoparticulate NaTi2(PO4)3 (NTP) powders as Na+-insertion hosts in either nonaqueous or aqueous electrolyte, correlating electrochemical properties such as capacity and electrode kinetics (in the form of powder–composite electrodes) with the degree of crystallinity in NTP. Starting with amorphous NTP powders prepared using the Pechini method, calcination from 500 to 800°C was used to induce varying degrees of crystallinity and to remove carbonaceous species. Poorly crystalline NTP powders derived by heating at 500–600°C exhibit low specific capacities and broad voltammetric features for Na+-insertion, characteristic of surface-limited processes. Heating at higher temperatures (700–800°C) yields the nanocrystalline form with the NASICON structure. Nanocrystalline NTP exhibits sharp voltammetric peaks and diffusion-limited kinetics in both aqueous and nonaqueous electrolytes. The electrochemical performance of nanocrystalline NTP is further enhanced when integrated with reduced graphene oxide (rGO) to increase local electronic conductivity; theoretical specific capacity for NTP (133 mAh g−1) is achieved when NTP-rGO is cycled in a nonaqueous electrolyte, and 100 mAh g−1 in a mild aqueous electrolyte. This nanocomposite also exhibits long-term stability (86% capacity retention after 1000 charge/discharge cycles) in a nonaqueous electrolyte.
A2131
Josh Wold, James Marcicki and Alvaro Masias
The successful electrification of the transportation and stationary power markets requires batteries with 10–30 years of lifetime. Validations of such long time scales can take several years and require significant confidence in future life predictions. Battery life predictions across such timescales can be highly sensitive to uncertainty in the collection of primary parameters such as current, voltage and time. A methodology to quantify how these primary parameters propagate into the derived parameters of interest such as capacity and coulombic efficiency is presented. The recent development of high precision battery testing and equipment has met the need for accurate and precise assessment of measurement errors. As an example of the derived quantity uncertainty propagation methodology and approach developed in this paper, a prototype high current, high precision tester is also evaluated. The aim of this paper is to describe a standardized method for the precise quantification of battery derived parameter uncertainty, apply the method to the performance of a prototype high current, high precision tester (HPT) as a case study, and then to model the sensitivity of these precision results across a population of possible test conditions.
A2138
The following article is Open access
Le Li, Lu Wu, Fang Wu, Shipai Song, Xiaoqing Zhang, Chen Fu, Dingding Yuan and Yong Xiang
The olivine structure lithium iron phosphate (LiFePO4) is considered as one of the promising lithium ion batteries cathode materials for its high theoretical specific capacity, excellent reversibility, thermal stability, environmental friendliness, and low cost. However, the application of LiFePO4 in vehicle power battery was hindered by its poor electronic and ionic conductivity. To solve these problems, various strategies, including surface coating, element doping, and particle size reduction were proposed. In this review, we summed up some recent researches on surface modification of LiFePO4 and explained the mechanisms of modification. Moreover, the defects and advantages of these modification methods were discussed. Finally, an outlook for the surface modifications of LiFePO4 cathode materials was given.
A2151
Yue Ru Li, Altug S. Poyraz, Xiaobing Hu, Michael Cuiffo, Clive R. Clayton, Lijun Wu, Yimei Zhu, Esther S. Takeuchi, Amy C. Marschilok and Kenneth J. Takeuchi
Birnessite type layered manganese dioxides (δ-MnO2) have attracted considerable attention in recent years as 2D intercalation cathodes for rechargeable Li+, Na+, and Mg2+ batteries due to fast ion diffusion through their negatively charged δ-MnO2 sheets separated by interlayer cations and a stable Mn3+/4+ redox couple. Here we report the preparation and electrochemistry of zero and divalent copper co-intercalated birnessite type manganese dioxide (Cu00.03Cu2+0.21Na0.12MnO2·0.9H2O). The copper intercalated birnessite materials were fully characterized utilizing powder X-ray diffraction (XRD), inductively coupled plasma optical emission spectroscopy (ICP-OES), transmission electron microscopy (TEM). The mixed valent nature of intercalated Cu0 and Cu2+ was confirmed by X-ray photoelectron spectroscopy (XPS) and electron energy loss spectroscopy (EELS). Electrochemical evaluation results show that zero valent copper intercalated birnessite exhibits higher discharge capability, improved cyclability, and lower impedance compared to the Cu2+ only intercalated (Cu0.26MnO2·1.0H2O) and Cu free Na birnessite (Na0.40MnO2·1.0H2O) materials. Remarkably, zero valent copper birnessite shows almost no fade after 10 cycles at 0.1 mV/s. Electrochemical impedance spectroscopy results suggest that charge transfer resistivity of Cu0 modified samples was much lower than that of Cu2+ and Cu free birnessite, indicating that the presence of a small amount of Cu0 improves the conductivity of birnessite and results in better electrochemical cyclability, rate capability, and lower impedance.
A2159
The following article is Open access
Kyriakos Giagloglou, Julia L. Payne, Christina Crouch, Richard K. B. Gover, Paul A. Connor and John T. S. Irvine
In this work CoNi2S4 was investigated as a candidate cathode material for Li thermal batteries. The CoNi2S4 was synthesized by a solid state reaction at 550°C in a sealed quartz tube. Neutron powder diffraction was utilized to confirm normal spinel structure up to 200°C, however, there was cation disorder above this temperature. The electrochemical properties of the batteries were investigated at 500°C by galvanostatic discharge to elucidate the mechanism and the products NiS, Co3S4 and Co9S8 of the discharge mechanism were confirmed using powder X-ray diffraction. CoNi2S4 exhibits two voltage plateaus vs Li13Si4 at 500°C, one at 1.75 V and the second at 1.50 V. CoNi2S4 has an overall capacity of 318 mA h g−1 from OCV 2.58 V to 1.25 V vs Li13Si4 which is comparable to that of the well-known metal disulfides.
A2164
The following article is Free article
J. Yan, W. J. Cao and J. P. Zheng
Lithium-ion capacitor (LIC) contains negative electrodes (NEs), positive electrodes (PEs), separator and lithium source for pre-lithiation of NEs. Activated carbon was used as the active materials of PEs, and hard carbon will be chosen as NEs. As we know, the specific capacity of NE is ∼372 mAh/g. The most concerned work for our cells now is the pre-lithiation method. With published data from Cao's group before, pre-lithiation with 99.9% purity Li strips can manufacture cells more efficient and safer than using stabilized lithium metal powder (SLMP). However, even this method may take up to 18 h for electrode to finish the pre-lithiation process. In this paper, five pre-lithiation methods for LICs were evaluated in this work, and strip cells were used as control samples and further provided the base for the whole comparison. This research brought up a new method of using 15∼20 um Li ultra-thin film for pre-lithiation. During tests, both sandwich LIC cells and 200F LICs were fabricated to demonstrate this new method. As supplementary evidence, DC life and cycle life tests were conducted after initial tests. Thus, 200F LICs using 20 μm Li film for pre-lithiation can achieve higher capacitance (246 F) and lower ESR (19 mOhm) than Li strip cells. Higher energy and power densities (26.9 Wh/L and 18.3 kW/L) have also been achieved. Moreover, sandwich cells with 15∼20 μm Li thin film has passed 100,000 charge-discharge cycle tests, and their capacitance and ESR can be maintain stable after 1500 h constantly charging at 3.8 V under 65°C.
A2171
The following article is Open access
David S. Hall, Ulrike Werner-Zwanziger and J. R. Dahn
Solid-state NMR spectroscopy was used to characterize the solid-electrolyte interphase (SEI) formed on the graphite electrode surface from the electrolyte additive pyridine pentafluorophosphate (PPF). The PPF-derived SEI was prepared in a full Li(Ni0.4Mn0.4Co0.2)O2/graphite cell, rather than in a coin cell or using a bench-top synthesis approach. 19F and 19F→31P cross-polarization measurements provide direct evidence that F atoms and P–F bonds are present at the graphite surface. By comparing rinsed and unrinsed samples, an insoluble SEI component was differentiated from residual LiPF6 from the dried electrolyte. The SEI species contains F and P chemical environments that are similar to, but distinct from, the additive starting material and the lithium hexaflurophosphate (LiPF6) electrolyte salt used in this work. The results are consistent with the previously proposed formation of a dilithium 4,4’–bipyridine-N,N’–bis(pentafluorophosphate) salt. LiF was also observed and is attributed to decomposition of the PPF-derived surface layer and/or the LiPF6 electrolyte salt.
A2176
G. Venkatesh, Brij Kishore, R. Viswanatha, Doron Aurbach and N. Munichandraiah
Research activities on Na-ion battery materials have gained importance in recent years as Na-ion batteries are considered as an economical substitute for the Li-ion batteries in some future applications. In the present work, P2-type Na0.67Mn0.65Fe0.20Ni0.15O2 was synthesized in microspherical morphology and characterized. Microspheres of FeCO3 were first prepared and used to synthesize Mn0.65Fe0.20Ni0.15CO3, followed by its thermal decomposition to the corresponding oxide and finally the thermal fusion of the oxide with Na2CO3 to produce P2-type Na0.67Mn0.65Fe0.20Ni0.15O2. The sodiated mixed metal oxide formed in microspherical morphology is in a pure crystalline phase with a mesoporous structure of average pore size 29 nm. Cyclic voltammograms of electrodes are characterized by well-defined two pairs of peaks corresponding to the oxidation and reduction processes in two different stages. The sodiated oxide provides an initial discharge capacity of about 216 mAh g−1 with an excellent cycling stability upon cycling at C/15 rate. The rate of decay in discharge capacity is about 0.3% per cycle at C/15 rate, but it increases to 0.9% per cycle over 100 continuous charge-discharge cycles at higher rates. The rate capability is also high and the discharge capacity is about 100 mAh g−1 at 2C rate. The high discharge capacity and high rate capability are attributed to the porous microspherical morphology.
A2183
Koichi Kajihara, Hayato Nagano, Takaoki Tsujita, Hirokazu Munakata and Kiyoshi Kanamura
Conductivity of a Mg2+-ion-conducting solid oxide Mg0.5−x(Zr1−xNbx)2(PO4)3 (x = 0.15) was measured with non-blocking Mg metal electrodes at 350°C in vacuum. The oxidation of Mg electrodes was suppressed by preventing their exposure to air throughout the deposition and measurements. The observed conductivity agreed with conductivities measured by ac impedance spectroscopy with blocking Pt electrodes. The transport number of Mg2+ ions derived from the conductivities measured with Mg electrodes by dc polarization method and ac impedance spectroscopy was ∼1. These observations evidenced that this compound is a pure Mg2+-ion conductor and stable in contact with Mg.
A2186
The following article is Open access
Zachary L. Brown, Sunhyung Jurng and Brett L. Lucht
The influence of vinylene carbonate (VC) on the plating/stripping of lithium was investigated using Cu||LiFePO4 cells. These cells allow for easy fabrication and in-situ generation of lithium, with no excess lithium to influence performance. Addition of VC to the electrolyte improves both capacity retention and efficiency. IR and XPS spectroscopy of the surface of the plated lithium suggests the presence of a significant amount of poly(VC) when the electrolyte (1.2 M LiPF6 in ethylene carbonate (EC): ethyl methyl carbonate (EMC) (3:7, vol)) contains 5% of added VC. This suggests employing additives that generate polymeric species on the surface of lithium improves plating/stripping performance in carbonate electrolytes.
A2190
Stephan Hildebrand, Christian Vollmer, Martin Winter and Falko Mark Schappacher
Al2O3, SiO2 and TiO2 were coated on LiNi0.8Co0.15Al0.05O2 (NCA) in varying amounts and investigated regarding their influence on thermal stability and electrochemical performance. The presence of the coating on the surface was confirmed by Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM). Al2O3 showed agglomerated nano-scaled particles. SiO2 was coated homogeneously. TiO2 showed loose nano-scaled particles on the surface. The coated materials showed a decrease in capacity of ≈10 mAh g−1 with slightly higher cycling stability compared to the pristine NCA. Accelerating Rate Calorimetry (ARC) of the delithiated materials was conducted with 1 M LiPF6 in ethylene carbonate (EC): diethyl carbonate (DEC) 3:7 (by weight) + 2 wt% vinylene carbonate (VC) + 0.5 wt% lithium bis(oxalate)borate (LiBOB). The TiO2 coating resulted in an increase of the onset temperature of thermal runaway (TdT/dt>0.2 K/min) of 5°C. Coatings with Al2O3 and SiO2 led to a significant increase of TdT/dt>0.2 K/min of up to 10 and 11°C, respectively. The coatings are able to lower the extent of reaction between the highly reactive oxygen evolving from the charged cathode at higher temperatures and the organic solvent-based electrolyte.
A2199
Z. Wang, J. Siegel and K. Garikipati
We present a coupled continuum formulation for the electrostatic, chemical, thermal and mechanical processes in battery materials. Our treatment applies on the macroscopic scale, at which electrodes can be modeled as porous materials made up of active particles held together by binders and perfused by the electrolyte. Starting with the description common to the field, in terms of reaction-transport partial differential equations for ions, variants of the classical Poisson equation for electrostatics, and the heat equation, we add mechanics to the problem. Our main contribution is to model the evolution of porosity as a consequence of strains induced by intercalation, thermal expansion and mechanical stresses. Recognizing the potential for large local deformations, we have settled on the finite strain framework. We present a detailed computational study of the influence of the dynamically evolving porosity, upon ion distribution, electrostatic potential fields, charge-discharge cycles and mechanical force generated in the cell.
A2213
Weiqiang Lv, Jianmin Gu, Yinghua Niu, Kechun Wen and Weidong He
Featured with ‘zero-strain’ structure and a lithiation potential of ∼1.55 V vs. Li+/Li, spinel lithium titanate (Li4Ti5O12, LTO) has found promising applications as an anode of lithium-ion batteries (LIBs) in large-scale, high-power stationary energy storage systems and electric vehicles/hybrid electric vehicles (EVs/HEVs). However, due to the gas formation in charge/discharge and regular storage processes, the practical applications of LTO are limited severely. Considerable efforts have been taken to reveal the gassing mechanism of LTO anodes. In this report, various gassing sources are investigated to provide a comprehensive overview on LTO gassing mechanisms which have been proposed. In addition, efficient solutions to suppressing LTO gassing are discussed systematically. This report is expected to provide the most up-to-date insights into LTO toward lithium-ion batteries with improved applicability.
A2225
Norihiro Togasaki, Tadayoshi Gobara, Toshiyuki Momma, Tetsuya Osaka and Tomoko Numata
Lithium nitrate (LiNO3) is a potential option for the lithium salt in lithium−oxygen (Li−O2) batteries because it reduces the charging overpotential on carbon-based cathodes and protects the lithium metal anode from side reactions. However, the cycling stability of an electrolyte containing LiNO3 in the presence of cathode catalysts has not yet been studied. In this paper, we report an improvement in the cycling performance of δ-MnO2 cathodes in Li−O2 batteries using LiNO3 in comparison with that of batteries using lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in DMSO-based electrolytes. A >50% improvement in cycling performance is obtained from the electrolyte with LiNO3 versus that with LiTFSI. While the charge−discharge voltage profiles of the two electrolytes are identical to each other, the electrolyte containing LiNO3 produces less side products such as C−F group compounds, Li2SO3, and Li2SO4 on the cathode surface. This may be due to the electrochemically stable behavior of LiNO3 and the preventive effect of NO3− on solvent decomposition, which stabilizes reactive species of superoxide radicals in the electrolyte.
A2231
Ran Attias, Daniel Sharon, Arie Borenstein, David Malka, Ortal Hana, Shalom Luski and Doron Aurbach
Chemically prepared manganese dioxide (CMD), which is traditionally used as a cathode material for Li-ion batteries, was tested and characterized for the first time as a positive electrode material for hybrid supercapacitors with two different aqueous electrolyte solutions (6 M KOH and 0.5 M K2SO4). The CMD electrodes exhibit distinct electrochemical characteristics that depend on the electrolyte solution used. The CMD electrodes show higher specific capacitance in the basic electrolyte solution, 137 F/g, at a current density of 0.1 A/g. Asymmetric supercapacitors comprising CMD positive electrodes and activated carbon negative electrodes were fabricated and tested within an electrochemical window wider than the thermodynamic voltage limitation for aqueous solutions. The asymmetric supercapacitors based on KOH and K2SO4 showed very good electrochemical stability during more than 7000 charge–discharge cycles and reasonable energy and power density. The electrochemical performance of CMD/AC asymmetric supercapacitors, their easy assembly, and their low cost make these super capacitors promising as practical energy-storage devices.
A2238
Mahmud Tokur, Ahmet Aydin, Tugrul Cetinkaya and Hatem Akbulut
The focus of the current study is to investigate the role of different carbon materials on the mechanical integrity and electrochemical stability of silicon anodes during cycling tests. Because, the electrochemical performance of the lithium ion batteries (LIBs) strongly depends on the mechanical integrity of Si during the lithium insertion process with huge volume change of silicon (∼300%) causes undesirable mechanical pulverization of electrodes that results in electrical disconnection between the active materials and the current collector, and eventual fast capacity fading. To this aim, multi-component anode materials were designed with various combinations of Si, Amorphous Carbon (C), reduced Graphene Oxide (rGO), and Carbon Nanofibers (CNFs) for high capacity and long stability LIBs. The stress generations in Si/rGO and Si/C/rGO were calculated after full lithiation of silicon and comparison of the contribution of the carbon shell to the deformation and stress in silicon was evaluated using finite element method in ANSYS design modeler. According to the experimental findings, Si/C/rGO/CNFs electrode has exhibited the highest reversible capacity of about 1750 mAhg−1 after 200 cycles and the fairly good integral stability against lithium insertion-induced expansion of a silicon.
A2251
Peter Michalowski, Alexander Gräfenstein, Martin Knipper, Thorsten Plaggenborg, Julian Schwenzel and Jürgen Parisi
Understanding the degradation of graphite anodes plays a major role in the improvement of Li-ion batteries. Herein, we used the nondestructive character of lock-in thermography (LIT) to investigate the aging of graphite anodes in pouch cells. The aged cells show a typical ring pattern in lock-in thermography images, which can be explained by the help of Raman spectroscopy. We attribute this pattern to the different contact due to the formation of a gas during operation, which also leads to inhomogeneous degradation of the graphite electrode. Finally, we demonstrate the detection of two-dimensional variances on the sub-mm scale in the composition of the graphite anodes in pouch cells by LIT. For this purpose, we combined LIT measurements with Raman spectroscopy mapping to link differences in the heat emission to those in the structure of the graphite.
A2256
Yan Xiang and Walid A. Daoud
In this study, indium modified carbon paper electrode is investigated as the positive electrode for all-vanadium redox flow battery (VRFB). The electrochemical performance is studied using cyclic voltammetry, electrochemical impedance spectroscopy and stability test toward V (IV)/V (V) redox reaction. The results show that the modified carbon paper exhibits excellent electrocatalytic activity and stability after repetitive 100-cycle test in an electrolyte containing 0.5 M VOSO4, while degradation is observed in pristine carbon paper. Such improvement is due to the indium particles deposited on the carbon fibers acting as stable active sites promoting the vanadium redox reactions and reducing charge transfer resistance as indicated by impedance measurement. Full cell performance is assessed via polarization curve analysis at different states of charge. A simple cell set-up (without flow field) employing the modified electrode exhibited limiting current of 125 mA cm2, which is 73% higher than the cell employing pristine carbon paper (72 mA cm2) at SOC of 96%. Overall, the results demonstrate that indium deposition on carbon paper promotes the electrochemical performance and provides an opportunity for further investigation in the exploration of metal modification of carbon materials for VRFB.
A2262
Hui Fan, Li Qi and Hongyu Wang
The electrochemical manner of hexafluorophosphate anion into a graphite electrode has been studied in mixed solvents of propylene carbonate (PC) and ethylmethyl carbonate (EMC). The successful electrochemical intercalation of PF6− has been gained in PC/EMC-based electrolyte solutions and the effect of PC and EMC on PF6− insertion into graphite in these electrolyte solutions has been studied by electrochemical tests, ex situ XRD and in situ Raman. Moreover, the interaction between anions and solvents in electrolyte solutions was investigated by nuclear magnetic resonance. Furthermore, Li/graphite cells based on these solutions cycled well.
A2268
Zhilong Wang, Tong Zhao and Masahiro Takei
The morphological structure characterizations of Lithium-ion battery (LIB) slurry have been clarified under shear rotational conditions of rotation speed n and rotation time t by on-line dynamic electrical impedance spectroscopy (EIS) method. The EIS Nyquist and Bode plots are fitted by 10-parameter electrical equivalent circuit (10p-EEC) to clarify electrochemical characteristics which are resistance, reactance and peak frequency of LIB slurry. Then, the on-line dynamic resistance of conductive path Rp, the time-averaged capacitances of PVDF-CB double layer Cdl and PVDF-NMP solution CSO are obtained, which results in the following morphological structure characterizations of LIB slurry. The network structure of LIB slurry is deteriorated in the low rotation speeds of n = 50 rpm and n = 150 rpm and is well constructed in the high rotation speeds of n = 300 rpm and n = 720 rpm. Moreover, PVDF-CB double layer is well formed with the increase of n. Furthermore, with the increase of t, the particle size of LiCoO2 coated by CB is slightly changed in the low rotation speeds of n = 50 rpm and of n = 150 rpm; however, the particle size of LiCoO2 coated by CB is increased in the high rotation speeds of n = 300 rpm and n = 720 rpm. The above-mentioned morphological structure characterizations are in agreement with those observed from morphological images of LIB slurry.
A2277
The following article is Open access
L. J. Krause, T. Brandt, V. L. Chevrier and L. D. Jensen
Li-ion pouch cells utilizing a negative electrode formulated with 15 wt% of an engineered Si alloy in a graphite composite electrode were cycled in an isothermal heat flow calorimeter against a LiCoO2 positive electrode. Two different electrolytes were investigated: a blend of ethylene carbonate and ethyl methyl carbonate (3EC:7EMC) and a blend of ethylene carbonate, ethyl methyl carbonate and 1-fluoro ethylene carbonate (27EC:63EMC:10FEC). Both electrolytes were 1 M in LiPF6 salt. The parasitic thermal power and coulombic efficiency was derived from isothermal heat flow measurements and high precision current-source meters. Cells without FEC showed high parasitic thermal power which increased with cycle number indicative of a surface area increase which was confirmed by post-cycling scanning electron micrographs and surface area measurements. Cells with FEC showed relatively stable parasitic thermal power. These measurements demonstrate the surprising function of FEC in controlling or attenuating the evolution of surface area in Si alloys. Vinylene carbonate was also found to be effective at controlling the increase in alloy surface area.
A2283
Yun Wang and Hao Yuan
This paper presents a fundamental study on the precipitate formation/morphology and impact of discharge precipitates in Li-air batteries and compares the voltage loss with two Li-air battery models, namely a film-resistor model and surface coverage model. Toray carbon cloth is selected as cathode, which serves as large-porosity electrodes with an approximately planar reaction surface. Imaging analysis shows film formation of precipitates is observed in all the experiments. In addition, toroidal and aggregate morphologies are present under lower currents as well. Specially, toroidal or partially toroidal deposit is observed for 0.06 A/cm2. Aggregates, which consist of small particles with grain boundaries, are shown for 0.03 A/cm2. We found that the film-resistor model is unable to predict the discharge voltage behaviors under the two lower currents due to the presence of the deposit morphologies other than the film formation. The coverage model's prediction shows acceptable agreement with the experimental data because the model accounts for impacts of various morphologies of precipitates.
A2290
Seong Heon Kim, Sung Heo, Jinsoo Mun, Gyusung Kim, Woon Joong Baek, Yong Su Kim, Sungsoo Han and Heechul Jung
Li-ion batteries (LIBs) with high performance in terms of high capacity and stability are in increasing demand for applications in a variety of energy-related fields, including next-generation electric vehicles. In this regard, attempts have been made to form a stable and robust solid electrolyte interphase (SEI) on LIB anodes, which can stably maintain the cyclic process of Li ion insertion/extraction into/from the anode materials. In this study, we coat the surfaces of LIB anode materials consisting of graphite and Si with poly(vinyl alcohol)-phosphate to form a stable SEI layer with high ionic conductivity and apply Auger electron spectroscopy (AES) to clearly detect the LixC6 (x < 1) phase generated by the permanent intercalation of Li into graphite interlayers. A comparative analysis based on AES clearly demonstrates that permanent Li intercalation into graphite interlayers is delayed by the oxide coating, resulting in both enhanced stability and reduced Li consumption at the anode.
Sensors
B391
M. F. Hossain, P. S. Das and J. Y. Park
A solvothermal technique with extra treatment was performed to synthesize high quality chemically modified graphene (CG). An environmentally friendly reducing agent, glucose, was used to obtain biocompatible chemically modified graphene. After acidic treatment of glucose treated chemically modified graphene (GCG), contamination free CG sheet was produced. CG suspension was cast on the surface of the plain biosensor surface and nylon filter paper. Pt nanoparticles (PtNP) were deposited on the CG decorated surface by cyclic voltammogram technique. Chitosan - glucose oxidase (chit-GOx) composite and nafion were then integrated by dropped casting technique on the CG/PtNP modified surface. This as-prepared biosensor showed high electrochemical activity for the detection of glucose in phosphate buffered saline (PBS) solution. It exhibited excellent analytical properties including a short response time (4 s), high sensitivity (69.44 μA/mMcm−2), and wide detection range (0.002–12 mM) for glucose sensing. The repeatability, reproducibility, interference phenomena and the stability of the developed sensors were also investigated. The CG based electrode was also evaluated for use as a dry electrode for ECG signal monitoring. The performance of the dry electrode was excellent in comparison to the conventional wet electrodes.
B397
Masahiro Nagao, Kazuyo Kobayashi, Peiling Lv, Shinya Teranishi and Takashi Hibino
The formation of highly oxidative and reductive states within and around WO3 and In2O3 during detection of NOx (NO and NO2) was investigated by attaching the metal oxide electrode to a proton-conducting Sn0.9In0.1P2O7 electrolyte, followed by electrode polarization at 200°C. Proton insertion and release occurred at the WO3 electrode, while metal-ion redox reactions proceeded at the In2O3 electrode. Although the hydrogen tungsten bronze formed under cathodic polarization was insensitive to NO and NO2, the WO3 operating under anodic polarization possessed sensitivity toward NO and NO2. Addition of these gases increased the ohmic, charge-transfer, and gas-diffusion resistances in a similar manner. The In2O3 underwent significant changes in NOx sensing ability upon changes in polarity and magnitude of the applied voltage. In particular, under cathodic polarization, the sensor resistance decreased upon addition of NO and NO2 in the range of –0.5 to –1.5 V, but increased upon addition at –2.0 V, due to reduction of In3+ to lower valence states, which selectively absorbed NO2 beginning at –1.7 V. The WO3 and In2O3 sensing abilities were not significantly affected by interference from O2, H2, CO, or n-C4H10, and the sensors became more sensitive toward NO2 as the WO3 and In2O3 particle size decreased.
B403
Mani Govindasamy, Rajaji Umamaheswari, Shen-Ming Chen, Veerappan Mani and Chaochin Su
The increasing concerns about food safety urged the desire to develop rapid and sensitive sensors for the detection of food contaminants such as pesticides. We described a reproducible and reliable screen printed carbon electrode (SPCE) modified with graphene oxide nanoribbons (GONRs) for sensitive determination of methyl parathion. The GONRs were prepared from carbon nanotubes (CNTs) and characterized by TEM, SEM, XRD, FT-IR, Raman, impedance and electrochemical techniques. Compared with CNTs, GONRs possess rich edge chemistry and abundant functional groups, higher area-normalized edge-plane structures and chemically active sites. As a result, GONRs/SPCE exhibits significantly improved electrocatalytic ability to methyl parathion in comparison with CNTs. The sensor exhibited two linear ranges; (1) 100 nM to 100 μM with sensitivity of 1.804 μAμM−1 cm2, (2) 100 μM to 2500 μM with sensitivity of 0.8587 μAμM−1 cm2. The detection limit was 0.5 nM (S/N = 3). The combined advantages of SPCE and GONRs make this method suitable for food robust real-time food analysis. The method is successful in the determination of methyl parathion in Ugli and tomato fruits, Beetroot and Broccoli indicating its excellent practical applicability. The other advantages of the electrodes are excellent stability, repeatability, reproducibility and high selectivity.
B409
Narendra Kumar, Satyendra Kumar, Jitendra Kumar and Siddhartha Panda
This paper presents an experimental investigation on the effect of pH sensitivity of the dielectric surface in field effect based sensors on the label free detection of prostate specific antigen (PSA). Two types of electrolyte-insulator-semiconductor (EIS) devices using covalently attached antibodies were used in this study; a device with low pH sensitivity showed ∼63 mV flatband voltage shift while a device with relatively higher pH sensitivity showed ∼23 mV shift with a PSA concentration of 10 ng/ml in buffer. These observations validated the reported theoretical models, and reconciled the other reported experimental observations using adsorbed antibodies. The effects of different steps of surface modifications using aqueous solutions to covalently attach the antibodies were investigated to understand governing mechanisms responsible for enhanced PSA detection with the device with low pH sensitivity. The variations in the flatband voltages, contact angles, and pH sensitivities confirmed the tunability of the low pH sensitive devices upon any charge associated with the biomolecules (PSA). The learning from this study could be utilized to enhance the sensitivity of conventional ISFET biosensors and more specifically that of devices with non-silicon based semiconductors as the chemical functionalization processes significantly affect their performance.
B417
The following article is Open access
Sunwoo Jung, Kwang Hyeon Baik, Fan Ren, S. J. Pearton and Soohwan Jang
The use of Ag in the gate region of AlGaN/GaN heterostructure diodes is shown to provide stable, reversible changes in barrier height and thus current during exposure to ethanol at 250°C. The exposed ethanol molecules are adsorbed on the silver and oxidized, resulting in the increase of Schottky barrier height. The detection limit of ethanol at this temperature was 58 ppm, and the sensor response was linear over the range 58–58700 ppm. For the high end of this concentration range (5.87%), ethanol exposure at 250°C caused the Schottky barrier height to change from 0.604 eV to 0.656 eV, which produced a forward current relative change of 45.4% at 0.9V forward bias. The results are competitive with detection of ethanol by oxide thin films or nanostructures of SnO2, Fe2O3, CuO, and ZnO.
B421
Jing Lu, Lin Wu, Yufang Hu, Sui Wang and Zhiyong Guo
A Faraday cage-type electrochemiluminescence (ECL) biosensor for ultrasensitive detection of cancer-associated microRNA-21 was constructed based on Fe3O4@Au magnetic nanoparticles (Fe3O4@Au MNPs) and multi-functionalized graphene oxide. The capture unit (Fe3O4@Au MNPs-cDNA) was prepared by immobilizing capture DNA (cDNA) on Fe3O4@Au MNPs, while the multi-functionalized graphene oxide acted as the signal unit ((sDNA&luminol)@GO). In this biosensor, the capture unit, which was used to catch the microRNA-21, could be easily attracted onto the magnetic glassy carbon electrode surface. After the hybridization of microRNA-21 with the capture unit, the signal unit was further hybridized to form a Faraday cage-type structure, in which the signal unit was directly fixed onto the electrode surface, resembling a huge net and even becoming a part of the electrode surface. All luminol molecules labeled on the signal unit could take part in the electrode reaction, thus greatly enhancing the ECL signal. The ECL intensity was found to increase with the logarithm of microRNA-21 concentrations from 1 fM to 10 pM with a detection limit of 0.3 fM. In addition, this proposed Faraday cage-type ECL biosensor can be used for practical analysis of microRNA-21 in human serum, providing an ultrasensitive detection platform for microRNAs in clinical diagnosis.
B427
Syeda Sara Hassan, Sallahuddin Panhwar, Ayman Nafady, Abdullah M. Al-Enizi, Sirajuddin, Syed Tufail Hussain Sherazi, Muhammad Siddique Kalhoro, Munazza Arain, Muhammad Raza Shah and M. Younis Talpur
In this study, a simple, faster and eco-friendly method was used for the synthesis of piroxicam drug derived gold nanoparticles (PX-AuNPs) in aqueous solution. The electrochemical behavior of paracetamol (PAR) was investigated at a PX-AuNPs modified glassy carbon electrode (GCE) by using differential pulse voltrammetry (DPV) in Britton Robinson Buffer solution in strong acidic medium. It showed excellent electrocatalytic activity towards the anodic oxidation of PAR at the peak potential value of 0.66 V and considerable improvement in the peak currents as compared to that observed at the bare GCE. The advantages are related to the unique properties of modified nanosensor such as large surface area, catalytic behavior and hence increased electron transfer abilities compared to GC electrode. The calibration of peak current vs. concentration of PAR was linear in the range of 0.05–12 μM with correlation coefficient R2 = 0.996 and limit of detection (LOD) of 5 nM. We successfully applied this sensor for determination of PAR in drug samples with a mean recovery of 99.7%. The proposed sensor is simple, novel, rapid, reproducible and sensitive. It can be used as an alternative for chromatography and other voltammetric methods involving mercury electrode. The proposed method could be used for water analysis from pharmaceutical industrial effluents and so on.
B435
V. C. Soorya and Sheela Berchmans
In this work, it has been demonstrated that the sequential inclusion of three catalytically active metals (Cu, Pt and Bi) in a glassy carbon (GC) matrix can ascribe a dual role to the trimetallic composite facilitating the oxidation and reduction of H2O2 under physiological conditions. The trimetal based nanosensing platform was constructed by sequential steps which included electrodeposition of Cu, galvanic replacement of Cu by Pt and irreversible adsorption of Bi over Pt. The electrocatalytic activity exhibited by the trimetallic composite was found to depend upon the composition and surface area. The Cu-Pt-Bi nanocomposite modified GC electrode (GC/Cu-Pt-Bi) effectively catalyzed the electrochemical oxidation and reduction of H2O2 at the potential of + 0.25 V and −0.01 V vs NCE (normal calomel electrode) respectively, with fast amperometric response, high sensitivity and low detection limit. Along with these attractive features, the modified electrode also displayed very high specificity to H2O2 with complete elimination of interference from uric acid (UA), ascorbic acid (AA), and glucose. These advantageous characteristics motivated us to build a dual mode cholesterol sensor based on H2O2 transduction by immobilizing cholesterol oxidase (ChOx) on GC/Cu-Pt-Bi. The enzyme modified nanostructured platform provided a highly sensitive and selective sensing of cholesterol coupled with a fast response time and low Km value.
B443
Livia Alexandra Gugoasa, Raluca-Ioana Stefan-van Staden, Ahmed Jassim Muklive Al-Ogaidi, Camelia Stanciu-Gavan, Jacobus Frederick van Staden, Marcela-Corina Rosu and Stela Pruneanu
Two stochastic sensors based on graphene powder modified with platinum and titanium dioxide (TiO2Pt/rGO) and 2,6-bis((E)-2-(furan-2-yl)vinyl)-4-(4,6,8-trimethylazulen-1-yl)pyridine (S1) and 2,6-bis((E)-2-(thiophen-3-yl)vinyl)-4-(4,6,8-trimethylazulen-1-yl)pyridine (S2) were proposed for the assay of three biomarkers monitorized in colon cancer: P53, KRAS and CEA. The limits of determinations were low, and the sensitivity very high. Whole blood samples from confirmed colon cancer patients were used for the validation of the method.
B448
The following article is Open access
Kannan P. Ramaiyan, Josh A. Pihl, Cortney R. Kreller, Vitaly Y. Prikhodko, Scott Curran, James E. Parks II, Rangachary Mukundan and Eric L. Brosha
A mixed potential sensor using Au and Pt dense wire electrodes embedded between tape-casted layers of 8 mol% yttria stabilized zirconia (YSZ) was tested for application toward NH3, NO, NO2, C3H6 and C3H8. In single-gas testing, the sensor exhibited the highest response toward NH3, while still exhibiting reasonably high sensitivity toward other interferent gases. The sensor was tested in a high-flow reactor at the National Transportation Research Center (NTRC) in order to simulate exhaust gas constituents and flow rates produced by lean-burn vehicles powered by Compression-Ignition Direct-Injection (CIDI), diesel engines. The sensor was characterized at 525 and 625°C for NH3, CO, C3H6, C3H8, and NOx in a base gas composition of 10% O2, 5% H2O, and 5% CO2 flowing at 15 slpm. The sensor exhibited fast response time equal to the response time of the system's switching valve (T90<0.6s). Moreover, in simulations of overdosing a selective catalytic reduction (SCR) system, the sensor was able to selectively respond to 20ppm injections of NH3 slip despite the presence of the interferent gas species at combined concentrations ten times higher than that of the NH3. The laboratory sensor construct was transitioned to a pre-commercial, automotive stick sensor configuration that was demonstrated to retain the advantageous characteristics of the tape-cast device.
B456
Xiaoxia Hua, Dong Tian, Fangquan Xia, Changli Zhou and Gang Wu
In this work, graphite-like carbon nitride nanosheets (g-C3N4) coupled with layered MoS2 were synthesized via a direct mixing and calcination method. Then they were studied as a new type of highly efficient luminescent material in an electrochemiluminescent (ECL) immunosensor. The prepared g-C3N4/MoS2 nanosheets exhibited strong and stable cathodic ECL activity compared to individual g-C3N4 and MoS2. One possible reason is that the synergy between the g-C3N4 and MoS2 would promote charge transfer and, thus, enhance the separation efficiency of electron-hole pairs. In addition, the combination also mitigates the passivation of g-C3N4. The ECL assay for alpha-fetoprotein (AFP) detection by using g-C3N4/MoS2 nanosheets was developed with excellent sensitivity at wide concentration ranges from 0.001 to 50 ng/mL. The limit of detection (LOD) is also down to 0.33 pg/mL, which is superior to other materials. Importantly, the designed immunosensor exhibited excellent selectivity, reproducibility, and long-term stability. The MoS2/g-C3N4 nanocomposite-based immunosensor is also promising for medical diagnosis.
B463
Mani Govindasamy, Sakthivel Kogularasu, Shen-Ming Chen, Yi-Hui Cheng, Muthumariappan Akilarasan and Veerappan Mani
Polyhedrons shaped three dimensional cobalt oxide (Co3O4 PHs) particles were synthesized via simple and facile hydrothermal synthetical route. The morphological, elemental, diffraction and electrochemical studies have been performed to verify the structure and shape. The Co3O4 PHs possesses good porosity, large electrochemical area, roughened surface, and stable electrochemical behavior. The Co3O4 PHs modified electrode was fabricated which displayed excellent electrocatalytic ability toward 4-nitrophenol (4-NP). A rapid, sensitive, selective, reproducible, and durable electrochemical 4-NP assay, by employing Co3O4 PHs modified electrode was described. The sensor displayed outstanding sensitivity with nanomolar limit of detection of 4.09 nM, which surpassed the detection limits of many previously reported sensors. The practical applicability of the sensor was successfully demonstrated in rapid in drinking water, which showed good recoveries. The facile synthetical route, easy fabrication and outstanding sensing attributes make this modified electrode as potential candidate in environmental analysis of 4-NP.
B470
Agnieszka Bala, Janusz Rębiś and Łukasz Górski
The feasibility of using gold electrodes modified with phosphorothioated oligonucleotides (PTOs) for determination of uranyl cation is described. PTOs are able of anchoring to gold surface via phosphorothioate linkers, present in its backbone. This approach is advantageous due to lack of the necessity of chemical activation before use and low cost. It was shown that the sensor sensitivity highly dependents on the incubation time in the sample solution. The developed biosensor demonstrated high selectivity toward UO22+ ion with minor interferences from other metal ions. A linear relationship between the changes in current signal derived from methylene blue – used as a redox marker – and the uranyl ion concentration up to 100 nmol·L−1 was obtained, with a detection limit of 14.7 nmol·L−1. In order to characterize the morphology of gold surface modified with DNA-SH or PTO, atomic force microscopy (AFM) was used. Interactions between UO22+ and the receptor layer (PTO) were studied using square wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS).
B476
Somayeh Mohammadi, Mohammad Ali Taher and Hadi Beitollahi
In the present work chitosan (CT) was used to construct a chitosan-modified carbon paste electrode (CT/CPE). The amine groups in the chitosan bind mercury ions from an aqueous KCl solution (PH 5.0). Then the electrode was held at a negative potential (−1.3 V) to reduce the Hg2+ bound to the CT/CPE to forming mercury nanodroplets. The proposed electrode was evaluated for preconcentration and determination of Tl+1 ions by differential pulse anodic stripping voltammetry (DPASV). The electrochemical procedure was based on the accumulation of thallium ions at the surface of the modified carbon paste electrode with mercury nanodroplets and chitosan biopolymer. Parameters involved in the binding of Hg+2 ions to the CT/MCPE, preconcentration of thallium ions and voltammetric stripping step were studied and the best set of experimental conditions were chosen. Under the optimized conditions, the voltammetric peak current of Tl+1 increased linearly with Tl+1 concentrations in the range of 1.0–400 ng mL−1 and a detection limit of 0.20 ng mL−1 was obtained for Tl+1. The practical application of the suggested modified electrode was evaluated by the determination of trace amount of Tl in the environmental and biological samples.
B482
Shalini Menon and K. Girish Kumar
A gold electrode (GE) modified with L-cysteine and gold nanoparticles (AuNPs) has been generated for computing the individual and simultaneous determination of nimesulide (NM) and acetaminophen (APAP). The electrochemical behavior of the pair of molecules has been inspected utilizing square wave voltammetry (SWV), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Studies indicated that the oxidation of APAP and NM is expedited at AuNPs/L-cysteine GE giving well defined peaks for APAP and NM at 0.596 V and 1.072 V respectively in Britton-Robinson (B-R) buffer (pH 2). The assay enabled simultaneous determination of these drugs in the linear working range of 3.0 × 10−4 M–1.0 × 10−5 M with detection limits of 4.06 × 10−7 M and 6.49 × 10−6 M for APAP and NM respectively. The high selectivity and sensitivity of the proposed assay were illustrated by its active application in the ascertainment of both APAP and NM in pharmaceutical preparations.
B488
Mehmet Bakir
In this study, Metamaterial Based Microfluidic Sensor (MBMS), which is designed by utilising a Split Ring Resonator (SRR) along with a patch has been employed to reveal the three different types of sensor applications by experimentally and numerically. These applications include purity demonstration of methanol, ethanol and acetone, different material sensing which is illustrated by poly ethylene glycol (PEG 300, PEG400) and temperature sensor application which is new in the current literature and proven by utilising pure ammonia solution. In the first step of the validation, these materials’ complex permittivity values were measured using an Agilent 85070E dielectric probe kit between 4 GHz and 6 GHz. Following this, a numerical simulation test was conducted by applying a FIT-based simulation programme. Finally, in order to verify the numerical simulation study, a proposed design has been manufactured prior to carrying out an experimental study on all of the applications. To support the simulation and experimental results, theoretical study carried out and obtained results were compared with similar studies. Both the numerical and experimental results reveal that the proposed Microfluidic sensor, which is based on a change in the complex permittivity, can be configured and applied to other sensing tools.
Corrosion Science and Technology
C465
The following article is Open access
Ying Jin, Min Liu, Chuanhui Zhang, Christofer Leygraf, Lei Wen and Jinshan Pan
This work presents a theoretical assessment of galvanic (relative) nobility of four intermetallic particles (IMPs), Al2Cu, Al2CuMg, Mg2Si and MgZn2, in aluminum alloys through work function calculation based on density functional theory (DFT). The concepts of work function, Volta potential and relative nobility are discussed with respect to the IMPs and aluminum matrix. The calculated Volta potentials are compared with reported experimental Volta potentials measured by scanning Kelvin probe force microscopy (SKPFM). Various crystal faces and terminal types are examined in the DFT calculation, showing that these two factors have a significant effect on the work function value. Considering the large divergence in the reported experimental data, the comparison shows a general agreement between the calculated and experimental Volta potential data for the investigated IMPs. The DFT calculations provide theoretical explanations for several experimental phenomena. The results demonstrate that DFT calculation is a valuable theoretical approach for assessment of the relative nobility of different phases in the alloys, providing complementary information to experimental data from SKFPM. Moreover, the implications of the calculated Volta potentials are discussed with respect to the corrosion potentials.
C474
Jianjun Gao, Zhilong Zhao, Lufeng Wei and Kai Cui
Directionally solidified NiAl–W pseudobinary eutectic alloys were selectively etched using an electrochemical system of three electrodes with pulsed potentials to remove the W fibrous phase, and nanoporous NiAl matrix was obtained. Experimental results demonstrated that the ammonium acetate solution has better dissolving efficiency than Na2HPO4−C6H8O7 buffer solution in selectively dissolving the W phases. The dissolving rate at the pulsed potential of 0.5 V is much higher than that of 1.0 V in the same dissolving duration. For polarization at the pulsed potential of 0.5 V, the pore diameter is a constant of 0.22 μm and the dissolving depth increases during the dissolving duration. Over-dissolving occurred at the pulsed potential of 1.0 V, led to the enlargement of the pores on the NiAl matrix. The number of connecting pores in the sample evidently increased with solidification speed from 8 μm/s to 15 μm/s.
C481
The following article is Open access
B. Laurent, N. Gruet, B. Gwinner, F. Miserque, M. Tabarant and K. Ogle
The rate of anodic dissolution and the associated activation potential that characterizes the passive-active transition of stainless steels have been measured directly for the first time in nitric acid. The anodic dissolution current under cathodic polarization in pure nitric acid, in absence of chlorides, is masked by intense cathodic hydrogen reduction. In this work, atomic emission spectroelectrochemistry (AESEC) was used to record simultaneously the dissolution rate of the individual alloying elements of stainless steels as well as the overall cathodic current. This methodology has been used to quantify the influence of several parameters on the activation potential: nitric acid concentration, temperature, and the addition of silicon in the steel composition.
C488
The following article is Open access
M. Iannuzzi, K. L. Vasanth and G. S. Frankel
Scanning Kelvin probe force microscopy was used to investigate the influence of microstructure on the corrosion behavior of nickel aluminum bronzes in ammoniacal and NaCl solutions as well as under potential control in Na2SO4. The results showed an inverse correlation between the measured Volta potential difference and the observed corrosion behavior. In other words, the phase with initially higher Volta potential was preferentially attacked whereas those with the lowest Volta potential difference values remained intact. This behavior suggests that Volta potential difference maps in air cannot be universally correlated with practical nobility or reactivity in solution, as proposed by other investigators. The implications of these findings are discussed.
C498
Kyohei Otani, Md. Saiful Islam and Masatoshi Sakairi
Inhibition ability of gluconates for fresh water corrosion of mild steel changed with metal cations were investigated by immersion tests and electrochemical impedance spectroscopy (EIS) tests. The results of the tests showed that the inhibition ability of gluconates was enhanced by metal cations that have large “corrosion inhibitory effect of cation, Y”, in model fresh water. Surface analysis showed that gluconate ligands and metal cations that have large Y can bond on mild steel and that they form a protective film on the steel. EIS analysis with an equivalent circuit suggested that metal cations that have large Y would reduce the area of defects in the protective film of gluconates.
C505
Yong Teck Tan, Sudesh L. Wijesinghe and Daniel J. Blackwood
Molybdate's inhibition of localized corrosion and passivation of AISI 1020 carbon steel in pH 9 and pH 10 solutions containing bicarbonate/carbonate and chloride anions was investigated under open-circuit conditions. The critical molybdate concentration required to prevent pitting corrosion in these solutions was determined. Using Design of Experiments and statistical analysis, the main and interaction effects of these anions on the polarization resistance were identified. Results show that the immersion time (a measure of the degree of passivation) and the presence of other ions can affect the effectiveness of a corrosion inhibitor. A combination of XPS and electrochemical methods was used to assess the effect of ions on the passive film formation. Increasing chloride concentration in the presence of bicarbonate/carbonate ions increased the total charge passed (extent of oxidation) but decreased the passive film thickness. This indicates that a significant part of the Fe atoms oxidized do not contribute to passive film formation, suggesting a harmful synergy between bicarbonate/carbonate and chloride. However, when molybdate is present, the total charge passed decreased and the passive film thickened slightly, showing the beneficial effect of molybdate on the passive film growth process, which is most probably due to competitive adsorption against bicarbonate/carbonate and chloride.
C516
F. Di Quarto, F. Di Franco, S. Miraghaei, M. Santamaria and F. La Mantia
A detailed study of the electronic properties of thin (<20 nm) anodic TiO2 potentiostatically grown on titanium in two different solutions is presented. The results show that the nature of the anodizing solution affects the electronic properties of the anodic film and, more specifically, the density of electronic states (DOS) distribution. Different DOS were derived from the experimental data analyzed according to the theory of amorphous semiconductor (a-SC) Schottky barrier. It is shown that the usual non-linear and frequency dependent Mott-Schottky plots are in agreement with expected theoretical behavior of a-SC Schottky barrier.
C526
The following article is Open access
Wenzhuo Deng and Jeffrey W. Fergus
The resistance of synthesized pyrochlore-type Gd2Zr2O7 bulk specimens to four calcium-magnesium aluminosilicate (CMAS) compositions at different temperatures was investigated. The reaction products were identified by X-ray diffraction and penetration depths were examined using scanning electron microscopy. A dense reaction layer is comprised mainly of Ca2Gd8(SiO4)6O2 and a cubic fluorite phase formed during the CMAS attack, and some unreacted CMAS was found in a transition layer below the reaction layer. The overall infiltration depth changed slightly with temperature, however, the thickness of the reaction layer and the morphology of the transition layer varied distinctly with temperature. The sintered sample underwent the most severe degradation by the CaO-lean CMAS, whereas the effect of CaSO4 and CaCO3 was not significant. Moreover, the Gd content of the ZrO2-based cubic fluorite phase depends on the temperature and the molar ratio of Ca:Si in the CMAS.
C532
The following article is Open access
Prasanna Jogdeo, Rosalie Chai, Sun Shuyang, Martin Saballus, Florentin Constancias, Sudesh L Wijesinghe, Dominique Thierry, Daniel J Blackwood, Diane McDougald, Scott A Rice et al
The understanding of microbial influenced corrosion (MIC) in aerobic mixed biofilms benefits from advanced microscopy and microbial ecology characterization of biofilms. Here, the onset of MIC in stainless steel coupons was studied in both natural and artificial seawater. Rapid selection of biofilm-forming microorganisms from natural seawater was observed for field experiments. Potential ennoblement was observed only in natural seawater. A seawater derived mixed microbial consortium enriched in artificial seawater was used to characterize the effect of several parameters on MIC. The concentration of organic carbon was the major determinant of MIC, while shaking speed and polishing played minor roles. The biofilm was preferentially formed at the grain boundaries. These results outline the need for MIC onset characterization with mixed microbial consortia to predict long-term corrosion behavior of stainless steel in seawater.
C539
The following article is Open access
Linda Wu, Dan Guo, Mi Li, Jiju M. Joseph, James J. Noël, Peter G. Keech and J. Clara Wren
Crevice corrosion of carbon steel was investigated in different exposure environments by performing coupon exposure and electrochemical tests. The extent of corrosion on the bold surface of a carbon steel crevice coupon was more severe at 80°C than at 21°C, in aerated rather than dearated solutions, and with γ-radiation present. In contrast to normal crevice corrosion, we observed ‘inverse crevice corrosion’ behavior, the phenomenon where it is the corrosion on the bold surface that is accelerated when coupled, rather than that on the crevice surface. The coupling current measured between a crevice and a bold electrode in an electrochemical cell was also negative. This inverse crevice corrosion behavior is attributed to a significantly lower metal cation dissolution capacity of the small occluded water volume in the crevice, compared to that of the bulk water volume over the bold surface. The reduction in dissolution capacity results in faster and earlier formation of a protective oxide layer. Corrosion of the bold and crevice surfaces evolves at different rates, leading to galvanically accelerated corrosion of the bold surface. The effect of γ-radiation on corrosion evolution in different solution environments leading to inverse crevice corrosion is discussed.
C554
The following article is Open access
N. Van den Steen, H. Simillion, D. Thierry, H. Terryn and J. Deconinck
Four different accelerated corrosion tests on steel are simulated with a Dynamic Electrolyte Film Corrosion model. Based on the time dependent temperature and humidity, combined with the presence of hygroscopic salts, a time dependent electrolyte thickness is calculated. At every timestep, the modeled film thickness dictates the corrosion current. Focussing on the thickness predictions, an elementary corrosion model is adopted to enable the corrosion depth estimations. The trends of the simulated corrosion depths are compared with experimental data obtained with an electrical resistance corrosion sensing system, demonstrating the importance of the electrolyte thickness and composition for a thorough understanding and modeling of atmospheric corrosion on steel.
C563
Yu-Min Chen, Nicholas G. Rudawski, Eric Lambers and Mark E. Orazem
The corrosion behavior of ASTM A416 steel in alkaline electrolyte was investigated by electrochemical and surface analysis approaches, including X-ray photoelectron spectroscopy (XPS) and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). The power-law model was used to extract values for oxide film thickness from constant-phase-element (CPE) parameters obtained as functions of operating conditions. Calibration experiments showed that, despite different silicon content in nominally identical steels, different film thicknesses as observed by HAADF-STEM, and different impedance responses, three samples yielded a common value for ρδ, an important parameter in the power-law model. Application of Monte Carlo simulations showed that values of both ρδ and film thickness δ followed log normal distributions. Application of the power-law model allowed extraction of film thicknesses, yielding 2–6 nm for silicon-rich steel and 1–2 nm for silicon-poor steel.
C574
The following article is Open access
Hongxin Wang, Yingwei Song, Jin Yu, Dayong Shan and Hou Han
The filiform corrosion of Mg–3Zn Mg alloy in various corrosion environments was investigated by scanning electron microscopy (SEM) observations, scanning vibrating electrode technique (SVET) and electrochemical measurements. The results indicate that corrosion filaments can cross grain boundaries and fine precipitation phases to develop continually. The propagation of filiform corrosion is greatly associated with the existence of Cl− in the solutions. A small amount addition of F− or SO42− to the NaCl solution can delay the initiation of filiform corrosion, while abundant F− or SO42− addition can change the corrosion forms. The micro–anodes and micro–cathodes transfer dynamically with the growth of corrosion filaments. Mg–3Zn alloy exhibits a filiform corrosion mode at the applied anodic potentials but keeps intact at the applied cathodic potentials.
C581
Maryam Eslami, Michele Fedel, Giorgio Speranza, Flavio Deflorian and Caterina Zanella
Cerium-based conversion coatings were deposited on high pressure die cast (HPDC) Al-Si alloys using an immersion method. Hydrogen peroxide and sodium chloride were added to the conversion solution to accelerate the coating formation and to understand its formation mechanism. These studies showed that the deposition of cerium hydroxide/oxide conversion layer starts from iron-rich intermetallic particles, which are located inside the eutectic region and then the coating growth continues to cover the entire alloy surface. This phenomenon passivates the active interfaces between iron-rich intermetallic particles and/or the eutectic silicon phase and the aluminum matrix, which are prone to localized corrosion in chloride ions containing environments. Accordingly, values of the total impedance in EIS measurements significantly increased for the treated substrates. Morphologies of the conversion coatings and the oxidation state of cerium compounds were found to be dependent on the composition of the solution and the presence of chloride ions and/or hydrogen peroxide. Aluminum alloy with higher silicon content showed a more active surface during immersion in the conversion solution. This makes it more difficult to be treated using aggressive conversion solutions.
C591
Chang-Geun Lee, Heon-Young Ha, Tae-Ho Lee and Kyung-Mox Cho
The effects of Nb on grain refining and pitting corrosion behavior of Febalance18Cr10Mn0.3C0.3NxNb (x = 0–0.5 wt%) alloys were investigated through microstructure analysis, potentiodynamic polarization tests, and passive film analyses. As Nb content increased, the grain size decreased and the volume fraction of Nb(C,N) particles increased. The pitting potentials of the alloys increased as Nb content increased up to 0.2 wt%, but further addition of Nb caused a decrease in the pitting potential. On the grain-refined alloy with the addition of 0.2 wt% Nb, a thick and less defective passive film was formed resulting in the rise of the pitting potential. On the other hand, the decrease in the pitting potentials of the alloys with the addition of Nb more than 0.3 wt% Nb was primarily attributed to the increased volume fraction of coarse Nb(C,N) which provided initiation sites for pitting corrosion.
C598
The following article is Open access
Jan Philipp Kollender, Andrei Ionut Mardare and Achim Walter Hassel
The dissolution of Ta in acidic media during both potentiodynamic and potentiostatic anodic oxide formation was quantified in-situ by ICP-MS. Potentiodynamic polarization yields a constant dissolution rate of 4 pg s−1 cm−2 (5 fm s−1) while a continuous dissolution rate decay was observed during potentiostatic anodization. The rate of Ta species release increased with applied potential in good agreement to the measured current density transients. A higher percentage of the charge carriers was identified as responsible for generation of soluble Ta species in potentiostatic regime as compared to potentiodynamic oxide growth. The current efficiency of anodization was determined from the combined investigation to exceed 99.9%.
C602
Lisha Wei, Zhenyu Chen and Xingpeng Guo
The inhibition effect of a synthesized imidazoline inhibitor on carbon steel in a supercritical CO2-H2O system was investigated using weight loss measurement, electrochemical tests, and surface analyses. In the presence of the imidazoline inhibitor, the corrosion rate and corrosion process showed minimal change with increasing CO2 partial pressure under non-supercritical CO2 conditions, whereas the corrosion rate clearly increased and the corrosion process greatly differed when the supercritical CO2 condition was reached. The introduction of KI substantially decreased the corrosion rate in the supercritical CO2 condition. The excess surface charge of the carbon steel changed from negative to positive as the partial pressure of CO2 increased to the supercritical condition, thereby hindering the adsorption of imidazoline inhibitor, which in turn decreased the inhibition efficiency.
Electrochemical/Electroless Deposition
D533
Shangshu Li, Xingli Zou, Xionggang Lu, Kai Zheng, Guangshi Li, Chaoyi Chen, Qian Xu and Zhongfu Zhou
Fe-TiC composite has been directly synthesized from natural ilmenite/carbon mixture precursors at 900–1000°C and 3.1–3.8 V in molten CaCl2. The pressed natural ilmenite/carbon mixture pellet was used as the cathode, and an inert solid oxide oxygen-ion-conducting membrane (SOM) tube filled with carbon-saturated liquid tin as well as a graphite rod were employed as the anode, respectively. The reaction mechanism of the electroreduction process from ilmenite/carbon mixture to Fe-TiC has been discussed based on the Rietveld refinement analysis, and the characteristic of the produced Fe-TiC composite has also been systematically analyzed. The result shows that the SOM-based anode electrochemical process possesses higher current efficiency compared with the graphite-based anode electrochemical process. The electrochemical process shows a considerable reduction speed due to the reinforcement of the in-situ reduction-generated Fe. The produced Fe-TiC composite shows homogenous structure. In addition, nanoscale TiC particles can be further produced through a facile leaching process from the obtained Fe-TiC composite. The TiC powder synthesized through the electrochemical process is of great potential to be used for the refinement for aluminum and/or aluminum alloys.
D543
The following article is Open access
James B. Marro, Chukwudi A. Okoro, Yaw S. Obeng and Kathleen C. Richardson
Organic additives are typically used in the pulse electrodeposition of copper (Cu) to prevent void formation during the filling of high aspect ratio features. In this work, the role of bath chemistry as modified by organic additives was investigated for its effects on Cu trench microstructure. Polyethylene glycol (PEG), bis(3-sulfopropyl) disulfide (SPS), and Janus green b (JGB) concentrations were varied in the Cu electrodeposition bath. Results indicated a correlation between the JGB/SPS ratio and the surface roughness and residual stresses in the Cu. Electron backscattering diffraction (EBSD) and transmission Kikuchi diffraction (TKD) were used to study the cross-sectional microstructure in the trenches. Finer grain morphologies appeared in trenches filled with organic additives as compared to additive-free structures. Cu trench (111) texture also decreased with increasing organic additive concentrations due to more pronounced influence of sidewall seed layers on trench features. Twin density in the microstructure closely tracked calculated stresses in the Cu trenches. A comprehensive microstructural analysis was conducted in this study, on an area of focus that has garnered little attention from the literature, yet can have a major impact on microelectronic reliability.
D551
Wei Weng, Mingyong Wang, Xuzhong Gong, Zhi Wang, Dong Wang and Zhancheng Guo
Direct preparation of metal titanium from soluble CaTiO3 in the Na3AlF6-AlF3 melt by electrolysis was confirmed, providing a short route for the high value utilization of CaTiO3 concentrates obtained from the titanium bearing blast furnace slag. The solubility of CaTiO3 in the Na3AlF6-AlF3 melt at 1253 K was determined by the isothermal saturation method and the electrochemical reduction behavior of TiO32− was investigated by cyclic voltammogram, square wave voltammogram, open circuit potential and potentiostatic electrolysis. The results indicated that the solubility of CaTiO3 in the melt was 2.4% at 1253 K. The TiO32− ions were reduced to metal titanium by the consecutive three-step reduction reactions: TiO32 − → TiO → Ti2O → Ti. The diffusion coefficient of TiO32− in the Na3AlF6-AlF3 melt was 6.7 × 10−6 cm2s−1 at 1253 K. The deposited metal titanium was successfully separated with Na3AlF6 by evaporation at 1823 K.
D558
Takatoshi Nagano, Kunihiro Tamahashi, Takashi Inami, Yasushi Sasajima and Jin Onuki
We estimated segregation energy for compound impurities at the grain boundary in very narrow Cu wires using the ab initio calculation. From the calculation results, we clarified that the impurities such as FeO, Fe(ClO), TiO and Ti(ClO) have a strong segregation tendency at the Cu grain boundaries. The FE-TEM observation results of the Cu wires with Fe impurity atoms confirmed that the impurity atoms led to smaller grain sizes than the impurity-free case. The resistivity was measured as a function of the Cu wire width for various Fe impurity concentrations and the wire resistivity became higher with increased impurity concentration.
D564
Van-Ha Hoang and Kazuo Kondo
Copper electrodeposition occurs in two steps and a practical electrodeposition normally needs several additives that require kinetic parameters for the calculation of current density and the concentration of intermediates. The copper electrodeposition was considered as a surface reaction, the exponential part of Butler-Volmer equation contributes to the value of reaction rate constant while the exchange current density relates to both the reaction rate constant and the surface concentration of cupric and cuprous ions. Two models for the adsorption of an additive or two additives on electrode surface were supposed. Using cyclic voltammetric stripping and chronoamperometry method, the electron bridge performance of chloride and the interaction of chloride with SPS were quantitatively compared with the non-additive copper electrodeposition.
D573
The following article is Open access
Pieralberto Collini, Sankalp Kota, Andrew D. Dillon, Michel W. Barsoum and Aaron T. Fafarman
Herein, we demonstrate the fabrication of Ti3C2Tx MXene films using electrophoretic deposition (EPD). A systematic study under constant voltage conditions from aqueous and propylene carbonate-based suspensions was performed to investigate the effects of the EPD process parameters on film morphology, flake orientation, and functional properties. From measured suspension properties, the kinetics of deposition from both suspension media were successfully described by the well-established Sarkar model of EPD. Remarkably, EPD-processed films have electrical conductivities of 7400 S/cm, on par with the highest values reported in the literature for Ti3C2Tx MXene. When employed as electrochemical capacitor electrodes in 1 M H2SO4, the capacitances were comparable to literature values. Given the process scalability and the morphological control that is possible, these results bode well for EPD as a fast, high-throughput method for making MXene films.
D581
P. Prabukanthan, S. Thamaraiselvi and G. Harichandran
Undoped and Co2+ doped FeS2 thin films (Co compositions are 1 to 5 mole%) were deposited on indium tin oxide glass substrate by a single step electrochemical deposition (ECD) method at low temperature (70 °C). Glancing angle X-ray diffraction (GAXRD) and Raman spectra showed that as-deposited undoped and Co2+ doped FeS2 thin films have a cubic pyrite structure without any trace of orthorhombic marcasite phase. Co2+ doping does not affect the cubic structure of FeS2 thin films with a strong (111) plane preferred orientation in all the doped thin films. The height profiling of 3 mole% of Co2+ doped FeS2 thin film by atomic force microscopy revealed a smooth surface with uniform distribution of particles and low roughness values. Co2+ (3, 4 and 5 mole%) doped thin films show a strong absorption peak in the higher wavelength region. Magnetic measurement reveals that Co2+ doping into the FeS2 lattice induces ferromagnetism. The Co2+ in FeS2 thin films acts as the acceptor and the original p-type conductivity is retained. Solar light irradiation with the intensity of 100 mW/cm2 on Co2+ (3 mole%) doped FeS2 thin film cell resulted in a power conversion efficiency of 5.42%.
D590
The following article is Open access
A. Nicolenco, N. Tsyntsaru and H. Cesiulis
Electrodeposited Fe-W alloys are the subject of extensive studies to be applied in versatile engineering applications, and many solutions based on Fe(II) complexes are described for their deposition. However, in aqueous solutions containing dissolved oxygen, Fe(II) compounds are unstable thermodynamically and tend to oxidize to Fe(III) state that decreases the sustainability of the baths. The aim of the present study was to develop an environment-friendly and thermodynamically stable Fe(III)-based electrolyte for electrodeposition of Fe-W alloys with tunable composition. It was found that: (i) concurrent use of two complexing agents as citric and glycolic acids stabilizes Fe(III)-based bath in neutral and weak alkaline medium (no precipitates are formed); (ii) the current efficiency of the process can reach up to 60–70%, which has never been reported before for Fe-W alloys electrodeposition; (iii) nanocrystalline Fe-W coatings containing 11–24 at.% of W can be obtained from Fe(III)-based glycolate-citrate bath at temperature range 20–65°C. The increase in tungsten content in the alloy resulted in decreased grain size up to < 5 nm; (iv) smooth, free of cracks and having deposition rates up to 0.18 μm/cm1 alloys are successfully electrodeposited at elevated temperatures from elaborated glycolate-citrate electrolyte.
D597
The following article is Free article
Abhishek Lahiri and Frank Endres
The need for a simple and versatile technique to develop various nanostructures for use in energy storage devices is in great demand. Electrodeposition is a versatile technique for developing various nanostructures on different substrates which can be directly used as battery electrodes. Thin film nanostructures, nanowires/nanotubes, core-shell and porous nanostructures, and three-dimensional ordered macroporous (3DOM) structures have been developed electrochemically and have shown better battery cycle lives, high charge/discharge capabilities as well as good capacity retention, sometimes at par or better than other synthesis techniques. This review highlights the synthesis of various nanostructures for use as battery electrodes for Li-ion and Na-ion batteries from aqueous, organic and ionic liquid electrolytes. In particular, we will highlight how ionic liquids have motivated the development of different intermetallic alloys and semiconductor nanostructures which have been applied in both Li-ion and Na-ion batteries.
D613
K. Mech, J. P. Chopart, M. Wróbel, P. Żabiński and K. Szaciłowski
Reported results concerning electrochemical co-deposition of nickel with palladium in Ni2+ – Pd2+ – Cl− – NH3 – H2O system. Obtained results indicated possibilities of synthesis of alloys of wide composition range, from 6.1 to 83.7 at. % of Pd. Electrodeposition of Ni-Pd alloys in the system was reported for the first time. Concentration of Pd in coatings was significantly higher than it was reported for Ni-Pd alloys deposited from sulfate-ethylenediamine and chloride electrolytes. Crystallite size of resulted alloys was definitely lower than reported in the literature. XRD analysis indicated that crystallites of electrodeposited alloys are of the diameter of few nanometers. Electrochemical tests reveal that simultaneous reduction of [Pd(NH3)4]2+ and [Ni(NH3)x(H2O)6-x]2+ complexes taking place at potentials more electronegative than ca. –0.5 V. Alloys were investigated toward their applications as catalyst for water splitting in alkaline sodium hydroxide solution. Observed Tafel slope amounting from 93 to 222 mV dec−1 indicated that in each case rate determining step (RDS) is water molecules reduction reaction.
D621
P. Tobosque, M. Maril, Y. Maril, C. Camurri, J. L. Delplancke, M. P. Delplancke, C. A. Rodríguez and C. Carrasco
Electrodeposited lead (Pb)–cobalt (Co) coatings are an effective electrocatalyst in the oxygen-evolution reaction. We studied the effect of an electrolytic bath pH on the electrodeposition of Pb–Co coatings, and the coating properties were analyzed. The pH was varied from 1 to 6 for a solution without and with ascorbic acid as complexing agent. Cathodic polarization curves show that the deposition conditions have a greater effect on the reduction potential of Co2+ than the reduction potential of Pb2+. Energy–dispersive X–ray spectrometer analysis shows that a pH higher than 4 promotes Co deposition and yields a [Pb]/[Co] film ratio lower than 1. Scanning electron micrographs showed that samples grown at a pH higher than 2 were covered with Co dendrites, and that the sample grown with ascorbic acid at pH 1 exhibited a compact morphology. Anodic polarization curves showed that Pb–Co-coated anodes grown at pH 1 with a complexing agent evolved oxygen at c.a. 1.6 V vs. normal hydrogen electrode, which lead to a 40% reduction in the required overpotential (η) for the oxygen-evolution reaction compared with conventional Pb–Ca–Sn anodes.
D626
Tomiyuki Arakawa, Kenta Chokki, Yuhei Nemoto, Nobuaki Watanabe, Kazuhiro Yabe and Ichiro Koiwa
Zn–TiO2–ZnO nanocomposites were obtained by pulse electrodeposition from non-suspended solutions containing ZnSO4·7H2O, TiOSO4·1–2H2O, sodium gluconate, and benzyldimethylphenylammonium chloride (BDPAC) without any particles. The surface morphologies, compositions, and crystalline structures of the electrodeposited nanocomposites were investigated by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy, and selected-area electron diffraction (SAED). BDPAC inhibited the deposition of zinc, promoted dendritic growth in the electrodeposit, and provided a titanium content [Ti/(Ti+Zn)] of more than 8 atomic%. Furthermore, a titanium content of 35.9 atomic% was detected in the electrodeposit produced from the BDPAC solution with optimized ZnSO4·7H2O concentration, temperature, pH, and duty cycle of pulse current. XPS and SAED revealed that TiO2 and ZnO were included in the electrodeposit. The electrodeposit was comprised of zinc, anatase TiO2, and wurtzite ZnO, and the grain size was in the range of 10–15 nm.
D631
Anne Karoline dos Santos Poli, Gustavo Machado Domingues Caetano, Ludmila Resende Vargas, Adriana Medeiros Gama, Maurício Ribeiro Baldan and Emerson Sarmento Gonçalves
The carbon materials and conducting polymers are known by application in electronic devices. This work aims to study the initial steps parameters of polyaniline electrosynthesis on carbon felts annealed at 1600 K by changing the number of voltammetry cycles in aniline acid solution. The characterization was performed by Field Emission Gun – Scanning Electron Microscopy, X-ray Diffraction, Infrared Fourier Transform Spectroscopy, Raman Spectroscopy and Electrochemical Impedance Spectroscopy. Under increasing number of cycles, the growth was more intense and it was easy to observe the pores clogging. Besides, it was noticed that emeraldine formation occurred progressively, from structures less to more oxidized: the polyaniline less cycled resulted closest that leucoemeraldine; polyaniline from nine cycles resulted closest to emeraldine, but all of them showed electroactive defects related to electrical charge (polarons) and conductivity (bipolarons). It was also observed that prime layers of polyaniline, formed until three cycles, followed more intense attraction of charges in solution to layer surface. This effect was emphasized from 3rd to 6th cycles.
D640
Jihyeon Park, Gibaek Lee and Jinsub Choi
In this study, the key anodization parameters of titanium for the formation of microcones were studied in detail. As the voltage increases, titanium oxides tend to transform from amorphous nanotubes to anatase microcones under certain electrolyte conditions. We found that a very small amount of H2SO4 is essential for the formation of microcones. In addition, if the concentration of HF is too small, a barrier-type oxide is formed. In contrast, the surfaces of the formed nanotubes are quickly dissolved at high concentrations of HF. The formed microcones have an average diameter of 2.58 μm and a height of 3.88 μm. The formation mechanism of the TiO2 microcones is related to the changes in the molar volumes of titanium metal and its oxide. From the current-time transients, the current density is considerably higher during the formation of TiO2 microcones compared to the formation of other structures, indicating that a high current leads to extremely high local heating, resulting in the amorphous-to-anatase phase transformation.
D645
H. P. Zhu, Q. S. Zhu, X. Zhang, C. Z. Liu and J. J. Wang
In this study, a modified Safranine T (mST) was used as a leveler in Cu electroplating for blind microvia filling. A perfect super-conformal filling effect was achieved by a combination of additives: polyethlene glycol (PEG), bis (3-sulfopropyl) disuldide (SPS) and mST. The filling time of the PEG-mST-SPS electrolyte was only half as long as that of the conventional PEG-JGB-SPS and the deposition thickness on the surface was one-tenth of that of the PEG-JGB-SPS. By electrochemical analysis, it was found that the composite suppressor of PEG-mST had a much stronger adsorption competitiveness against SPS on the surface, but a much weaker competitiveness against SPS at the microvia bottom. Based on that, it was deduced that the PEG-mST would occupy the most of the locations on the surface and the SPS would occupy the most of locations at the microvia bottom, which might account for such a perfect bottom-up filling mode, an ultra-thin surface thickness and an ultra-fast filling speed. But it brought about a risk of overfilling bump phenomenon under high mST concentration and strong convection force. This study proposes that the modified hydroxy in mST molecular structure might play a key role in this filling performance.
D652
Gongsheng Song, Yanpeng Yang, Qiang Fu and Chunxu Pan
In this paper, the copper (Cu)-graphene (Gr) composite thin foils with a thickness around 20 μm were prepared by means of a direct current (DC) electro-deposition method. The effect of three vital factors, i.e., graphene oxide (GO) concentration in the electrolyte, applied current density and bath temperature on the microstructural variations and mechanical properties of the composite thin foils was investigated in detail. The experimental results revealed that: 1) with increasing GO concentration, the microstructures or grains of the composite thin foils varied from needle-like → compact grains → large triangle cone. The optimal value was 0.5 g/L. 2) At the 0.5 g/L GO concentration, the higher the current density was applied, the smaller the grain size of the foils was observed until a critical point (10 A/dm2), and then kept unchanged essentially. The graphene distributions within the foils were relatively uniform except for aggregations under high current density (20 A/dm2). 3) The high temperature leaded to large grain size and more Gr aggregations. 4) According to the tests of mechanical properties, the optimized processing conditions were as follows, 0.5 g/L GO concentration, 10–20 A/dm2 applied current density and 25–40°C temperature. The influencing mechanisms of the factors were also discussed.
D660
The following article is Open access
Po-Fan Chan, Rung-Hsuan Ren, Shih-I Wen, Hou-Chien Chang and Wei-Ping Dow
This study focuses on the effects of plating additives and forced convection on microstructure and surface roughness of a copper foil at high current densities. A pilot Cu plating bath was designed according to the simulation of flow field using COMSOL Multiphysics. Accordingly, accurate fluid flow rates and the streamline patterns thereof were obtained in this work. The surface roughness of copper deposit depended on the limiting current density of cupric ions, the distribution of adsorbed chloride ions and the adsorbed organic additives at high current densities (10∼60 A·dm−2). Forced convection has strong influence on these factors as mentioned above. A copper foil with low surface roughness could be consequently obtained for the application of high frequency transmission in printed circuit board industry.
D666
Aimin Liu, Zhongning Shi and Ramana G. Reddy
In this study, zinc oxide (ZnO) was dissolved in 2:1 mole ratio of urea/1-butyl-3-methylimidazolium chloride (urea-BMIC) ionic liquids and electrochemically reduced to metallic zinc (Zn) on the cathode. The electrochemical behavior of zinc species in the urea-BMIC-ZnO ionic liquids was investigated by cyclic voltammetry, chronopotentiometry, and chronoamperometry techniques at 373 K using a tungsten working electrode and silver reference electrode. The cyclic voltammograms and chronopotentiograms indicate that the reduction of zinc species to metallic Zn is a diffusion-controlled quasi-reversible process and it proceeds via an apparent two-electron transfer process on tungsten working electrode. From the chronoamperometric analysis, zinc deposition in urea-BMIC involves in a three-dimensional instantaneous nucleation and diffusion-controlled growth at 373 K. The value of diffusion coefficient of zinc species in the urea-BMIC (molar ratio 2:1) ionic liquids at 373 K is 4.39 × 10−9 cm2·s−1. Zinc coatings were prepared on copper substrates at various current densities (constant current electrolysis) and different cathodic potentials (constant potential electrolysis). SEM micrograph indicated that a uniform, dense, and compact coating was produced by potentiostatic electrolysis at −1.1 V (vs. Ag). In addition, the obtained electrodeposit on the Cu substrate was metallic Zn as confirmed by XRD pattern and EDS spectrum. The optimized current efficiency (99.24%) and energy consumption (3.29 kWh/kg) was obtained by potentiostatic electrolysis at −1.1 V (vs. Ag) and 383 K in urea-BMIC ionic liquids containing 0.49 mmol/mL ZnO.
D674
Bamidele D. Falola, Li Fan, Tomasz Wiltowski and Ian I. Suni
Cu-doped MoS2 thin films were prepared by one-step electrodeposition from 10.0 mM (NH4)2MoS4, 5.0 mM CuSO4, 0.10 M KCl and 0.50 M KSCN at pH 6.95, followed by annealing for three hr. at 500°C in Ar. Cyclic voltammetry in the presence of the SCN— complexing agent yields a cathodic deposition peak that is slightly anodically shifted (∼90 mV) relative to the cathodic deposition peaks observed for elecrolytes containing only Cu2+ and only MoS42−. This may provide evidence for the induced co-deposition mechanism, but it is unclear which specific compound is formed. According to RBS and EDX analysis, thin film deposits contain 1–4 atom% Cu and are sulfur-deficient relative to stoichiometric MoS2. Cu dopant incorporation reduces the film resistivity by ∼10x relative to undoped MoS2. The specific capacitaqnce of Cu-doped MoS2 was also measured by both cyclic voltammetry (CV) and galvanostatic charge-dischrarge (GCD). For 500 nm thick annealed MoS2 films, the specific capacitance of Cu-doped films ranges from 2.5–3.5x higher than that of undoped films during 1000 cycles of CV testing in 1.0 M Na2SO4. Capacitance testing also reveals better capacity retention and high scan rate performance for Cu-doped relative to undoped MoS2 films.
Electrochemical Engineering
E173
Huang Qian, Lv Jinlong, Liang Tongxiang and Wang Chen
Hydrothermal method is used to in situ synthesize mesoporous graphene@NiMoO4 nanocomposites as supercapacitor electrodes. NiMoO4 nanorods are formed on fresh graphene surface, while scattered NiMoO4 nanoparticles are obtained on the surface of ball milled graphene. graphene@NiMoO4 nanocomposites electrodes exhibit a higher electrochemical performance compared with a pure NiMoO4 electrode, and the ball milled graphene@NiMoO4 electrodes have the maximum specific capacitance of 2100 F g−1 at 1 A g−1 discharge current and maintains at least 92% of its initial capacitance after 5000 operational cycles. Such an enhanced supercapacitive performance originates from the mesoporous structure, more electroactive sites, large specific surface area, high electrical conductivity and synergistic effect between NiMoO4 and the graphene.
E180
Ozge Turkay, Sibel Barışçı, Bahar Öztürk, Hazal Öztürk and Anatoli Dimoglo
The degradation of phenol by novel electro-peroxone (E-peroxone) was investigated in this study. In the first stage of the work, different cathode materials (carbon-PTFE, bronze doped carbon-PTFE and stainless steel) and experimental conditions (i.e. inlet ozone concentration) were evaluated for H2O2 generation. All cathode materials apart from stainless steel generated high amount of H2O2 within 10 min. However, when two carbon-PTFE were used as cathodes, the production rate was faster than the usage of one carbon-PTFE cathode. The production capacity of H2O2 and •OH radical in the E-peroxone, ozonation and electrooxidation (EOX) processes were presented comparatively. While high concentration of •OH radical was generated in both ozonation and E-peroxone processes from the first min, there was no •OH radical production in EOX. While the phenol degradation rate was noticeably low in EOX, E-peroxone process provided complete degradation of phenol. The removal rate was also high in ozonation but it was slower than E-peroxone. Transformation by-products were identified by HPLC. The E-peroxone process leads to the formation of aromatic compounds such as p-benzoquinone, hydroquinone and pyro-catechol, and aliphatic carboxylic acids, mostly oxalic acid and maleic acid. E-peroxone process was found the most cost effective process with 0.0032 kWh g−1 specific energy consumption.
E187
Siwei Zhao, Ji Xing, Haowen Fan, Shaoyu Zhang, Dongdong Li and Xufei Zhu
Due to certain limitations of traditional models, the growth mechanism of porous anodic TiO2 nanotubes has not been well determined currently. Herein, for the first time, a mathematical model of voltage-time transient curves under constant current conditions is derived theoretically, based on the conception of ionic and electronic currents and Ohm's law. The simulation results show high fidelity to the experimental curves, and illustrate the linear correlation between nanotube length and ionic current. Further, based on this model, the avalanche breakdown can be explained, which shows advantage over the former derivations on compact films. And this model indicates that the discrepancy between compact and porous oxide films lies on the magnitude of electronic current during anodization. Moreover, the proportion of the ionic and electronic current is then calculated during constant current anodization. It can be concluded that the ionic current contributes to the oxide growth while the electronic current gives rise to the oxygen bubble evolution which acts as the growth mould of the oxide. The present results promote the understanding of the growth kinetics of porous anodic oxides from qualitative interpretation to quantitative analyses.
E194
The following article is Open access
T. Baldhoff, V. Nock and A. T. Marshall
Aluminum micro-channels have been machined in phosphoric acid via mass-transfer limited electrochemical dissolution through photoresist masks. The results of shape evolution experiments using a rotating disk electrode are presented in terms of the dimensions, shape profile and uniformity of the machined micro-channels. The influences of applied potential, cumulative passed charge and hydrodynamic conditions on the shape evolution process are discussed. Experimental results are compared with a shape evolution model assuming the rate of aluminum removal is solely controlled by diffusive mass transfer. The degree of agreement between experimental and simulated results depends mainly on the hydrodynamic conditions in the electrochemical cell and indicates a shift from purely diffusive to mixed convective-diffusive mass transfer. The feasibility of electrochemical aluminum micromachining is demonstrated by fabricating microfluidic test structures with well-defined geometries and smooth surfaces.
E203
Amanjit Singh, Anoop Verma, Palak Bansal and Jayishnu Singla
The simultaneous reactions at anode and cathode makes study of individual processes difficult. In this paper the parameters for both the cathodic reactions and anodic catalytic activity are independently studied from each other using graphite electrode. The cathode based electro-Fenton and anodic electro-chlorination has been studied for degradation and decolorization of Reactive Black 5 (RB 5) dye. Process parameter interaction and optimization has been done using response surface methodology (RSM), central composite design matrix with statistical analysis including ANOVA and 3D plots. Electro-Fenton treatment was studied for pH, catalyst concentration, current applied and distance between the electrodes with pH, catalyst concentration and current applied being significant for both decolorization and degradation. Statistical analysis depicted the significant role of pH, current applied and distance between the electrodes in the electro chlorination treatment of RB5. Carbon as cathode was extremely effective however, in case of anode the carbon has low stability near oxygen evolution potential.
E213
Rawdha Ennouri, Mouna Kchaw, Marco Panizza and Sourour Chaabane Elaoud
The electrochemical oxidation of vanillic acid (4-hydroxy-3-methoxybenzoic acid), one of the most representative phenolic type compounds present in olive oil mill wastewater, was studied by galvanostatic electrolysis using boron-doped diamond (BDD) as anode. The influence of several operating parameters, such as applied current density, initial vanillic acid concentration, temperature and initial pH value was investigated. Measurements of Chemical Oxygen Demand (COD) were used to follow the oxidation. The experimental data indicated that the COD removal follows a pseudo first-order kinetics and the apparent rate constant increased with the applied current and temperature and decreased with pH and organic concentration.
E217
Dalsung Yoon and Supathorn Phongikaroon
The electrochemical techniques including cyclic voltammetry (CV), open circuit potential (OCP), and electrochemical impedance spectroscopy (EIS) were performed to understand fundamental behaviors of UCl3 in LiCl-KCl salt at concentrations ranging from 0.5 wt% to 4 wt% and temperatures from 723 K to 798 K. In addition, the same measurements were performed in LiCl-KCl-UCl3-GdCl3 for evaluating the effects of GdCl3 co-existence on uranium properties. Diffusion coefficients (D) of UCl3 was calculated by measuring reduction peaks of U3+/U in CV experiments. The values of D were linearly correlated with temperature, but weakly affected by concentration under 4 wt% of UCl3. The addition of GdCl3 showed no significant changes in D values. The equilibrium potentials (E) of U3+/U couple were measured from OCP data and no significant influence of GdCl3 was observed on the E trend. From the measured E values, the apparent standard potentials and thermodynamic properties of U3+/U were calculated and reported in this study. Lastly, EIS measurements were performed to explore the exchange current densities (i0) of U3+/U, showing linear relationships with both temperature and concentration, which were expressed using a simple linear correlation. Values of i0 followed the same linear expression regardless of GdCl3 presence in the system.
E226
V. N. Duradji, D. E. Kaputkin and A. Y. Duradji
This article briefly reviews modern methods for oxidizing coating of valve metals (Al, Ti, Mg, etc.). These methods include microarc oxidation, plasma-electrolytic-arc oxidation, anodic - spark oxidation. Their common characteristics as well as differences between these methods and electrolyte-plasma processing by electrohydrodynamic mode of anodic process are described. The composition, microstructure and surface morphology of the coating formed on the surface of titanium alloys depending on the electrolyte-plasma processing parameters are investigated.
E233
The following article is Open access
Weizhi Zeng, Shijie Wang and Michael L. Free
Impurity particles (slime particles) play a vital role in copper electrorefining, as they are a major source of cathodic contamination. Their behavior and transport in electrorefining cells are largely affected by electrolyte flows. Therefore, it is significant to study the fluid flow field in copper electrorefining with the consideration of impurity particles. A two-phase flow model of copper electrorefining was developed with one liquid phase of electrolyte and one dispersed phase of impurity particles. Copper electrorefining in a lab-scale cell was then simulated for two different impurity particle releasing scenarios. With impurity particle released only from the inlet, dispersed phase particles can be transported to the inter-electrode domain by electrolyte inflows through its sides rather than its bottom. Thus, the side parts of the cathode encounter more impurity particles than the center part in this scenario. With impurity particles released from both the inlet and the anode, dispersed phase particles fill up the electrorefining cell much faster, and the cathode is exposed to significant volume fractions of the dispersed phase much earlier. A large amount of impurity particles from the anode are settled on the cell bottom. The dispersed phase particles are distributed almost uniformly in front of the cathode after initial stages.
E242
The following article is Open access
Ayokunle Omosebi, Xin Gao, Nicolas Holubowitch, Zhiao Li, James Landon and Kunlei Liu
The electrochemical response of capacitive deionization (CDI) employing a single anion exchange membrane (AEM-CDI) is contrasted to conventional two-membrane CDI (MCDI) formed with complementary anion and cation exchange membranes. Pristine activated carbon cloth electrodes that possess native positive surface charge in solution were used as both anode (positive electrode) and cathode (negative electrode) in these cells. In a separate set of tests to investigate the impact of surface charge modification on deionization responses, the single and dual membrane cells were formed with asymmetric electrodes (AEM-aCDI and aMCDI) consisting of nitric acid oxidized electrodes that possess negative surface charge as the cathode material, while pristine carbon cloth was retained as the anode material. Operating at 1.2 V, salt adsorption capacities are ∼1.3, 9.9, and 16.6, and 17.3 mg NaCl g−1 electrode for the AEM-CDI, MCDI, AEM-aCDI, and aMCDI, respectively. The diminished performance of AEM-CDI is attributed to charge expulsion and enhanced parasitic electrochemical reactions at the unprotected cathode that reduce the charge efficiency. In contrast, for AEM-aCDI, a treated cathode enhances surface charge effects to match aMCDI performance with half the membrane requirement.
E248
H. D. He, N. S. Qu, Y. B. Zeng and P. Z. Tong
Wire electrochemical micromachining (WEMM) has increasingly come to be recognized as a flexible and effective method for producing planar contour microfeatures. The machining performance of WEMM is significantly influenced by the mass transport rate in the machining gap. Recently, it has been found that the use of a wire electrode with surface microstructures further increases the mass transport rate. Nevertheless, the mechanism through which the microstructures on the wire surface affect the flow field in the machining gap has been poorly understood. In this paper, a simplified mathematical model taking account of the velocity slippage caused by hydrogen bubbles attached to the axially traveling wire surface is first established. The effects on the flow field distribution in the machining gap of surface hydrophilicity and microstructures on the wire surface are theoretically analyzed. The results show that the microstructures facilitate rapid detachment of hydrogen bubbles from the wire surface, resulting in a reduction in velocity slippage and increasing the mass transport rate. A series of comparative experiments on WEMM using both smooth wires and microstructured wires prepared by laser direct scanning machining are conducted. The results are in accordance with the theoretical analysis.
E260
Wenliang Song, Yu Zhang, Hua Jin, Mi-Ra Kim, Seok Kim and Il Kim
A highly active and stable praseodymium-polyvinylpyrrolidone (Pr-PVP)-co-doped nanoTiO2 film/titanium matrix was successfully fabricated for the electrocatalytic reduction of oxalic acid. The structure, morphology, and electro catalytic activity of the as-synthesized Pr-PVP-doped nanoTiO2 film on a titanium matrix surface was studied with X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The electro catalytic properties were assessed by studying the electro reduction of oxalic acid on Pr-PVP-co-doped nanoTiO2 film electrodes. The results showed a high yield of glyoxylic acid (82.6%) and a high current efficiency (81%) with galvanostatic preparative reduction. Based on the results, Pr-PVP-modified nanoTiO2 film has a large electrochemical active surface area and small charge transfer resistance. The good electro catalytic performance of Ti/Pr-PVP-nano TiO2 makes it promising for use as an electrode in the electro catalytic reduction of oxalic acid.
E265
Emília Kubiňáková, Vladimír Danielik and Ján Híveš
The electrical conductivity of low-temperature electrolytes based on Na3AlF6 was measured by means of a tube-type cell. AC-techniques with a sine wave signal in the high frequency range were applied. Basic binary melts NaF-AlF3 were studied at different molar cryolite ratios MR = (2.0–1.2) in the temperature range from the temperature of primary crystallization to 100°C overheat. The influence of the additions of 2 wt% of Al2O3, 5 wt% of CaF2 or 2 wt% of MgF2 was investigated at the same conditions, as well. The temperature and concentration dependencies of the conductivity in the studied systems were determined.
E270
The following article is Open access
Matthew E. Suss
Capacitive deionization (CDI) is a fast-emerging technology most commonly applied to brackish water desalination. In typical CDI cells, dissolved ions are removed from the feedwater and stored in electric double layers (EDLs) within micropores of electrically charged porous carbon electrodes. Recent experiments have demonstrated that porous carbon CDI electrodes exhibit selective ion removal based on ion size, with the smaller ion being preferentially removed in the case of equal-valence ions. However, state-of-the-art CDI theory does not capture this observed selectivity, as it assumes volume-less point ions in the micropore EDLs. We here present a theory which includes multiple counterionic species, and relaxes the point ion assumption by incorporating ion volume exclusion interactions into a description of the micropore EDLs. The developed model is a coupled set of nonlinear algebraic equations which can be solved for micropore ion concentrations and electrode Donnan potential at cell equilibrium. We show that our model predicts the non-unity separation factor observed experimentally in CDI systems with two equal-valence counterions, which could not be explained by previous CDI theory. Further, our theory captures the measured values of the separation factor when using the hard-sphere diameter as an adjustable parameter.
E276
M. Doležel and K. Keslerová
The driving force of electrodialysis is applied voltage and electric current. In the event that the module is composed of a number of mutually hydraulically connected subunits (membrane pairs), electric current passes through a part outside the active part along peripherals providing the supply of raw materials. This work focuses on the measurement of these currents that are lost inefficiently. The influence of module geometry on electrodialysis, conductivity of working solutions and applied voltage were studied. The influence of the presence of an ion-conductive membrane in the sealing area on the performance of a membrane stack has been proven. A relation between the conductivity of a membrane and the conductivity of electrolytes to the amount of leakage currents has been found. On the contrary, voltage applied does not primarily influence the distribution of leakage currents but it affects the degree of desalination and the conductivity of solutions in collecting and feeding channels. In the pilot and operating modules with 25 and 50 membrane pairs that were used, the calculated leakage current reaches 0.2–1.2% of the total current load depending on the design and operating conditions.
E283
Prabhjot Kaur, Sangeeta Sharma and M. K Kushwaha
Iron nanowires were successfully prepared by electrodeposition method via ordered nanoporous anodized aluminum oxide (AAO) template since the technique is simple and cost-effective. The preparation of nano porous anodized aluminum template involved annealing and electropolishing as a pretreatment. It has been found that regularity of pores increases after the pre-treatment. The average surface roughness factor (Ra) was measured with the help of portable surface roughness tester. Pore diameter, pore density, porosity and uniformity of pores was determined with the help of image-J software. Morphology of nanoporous oxide and iron nanowires was confirmed with FE-SEM and EDS analysis. The pore diameter of template ranged from 105 nm to 120 nm. The fabricated nano wires were found to have length of 643 nm and diameter of 103 nm with unique environmental applications.
Fuel Cells, Electrolyzers, and Energy Conversion
F889
The following article is Open access
Pramote Puengjinda, Hanako Nishino, Katsuyoshi Kakinuma, Manuel E. Brito and Hiroyuki Uchida
We have developed high-performance double-layer (DL) hydrogen electrodes for reversible solid oxide cells. The DL hydrogen electrode consisted of mixed conductor, samaria-doped ceria (SDC), with highly dispersed Ni or Ni-Co nanocatalysts as the catalyst layer (CL) and, on top of it, a thin Ni−SDC cermet as the current collecting layer (CCL). The performance of the DL hydrogen electrode was appreciably improved by controlling the microstructure. The use of a thin, porous CCL increased the electronic conducting path to and from the CL, while maintaining sufficient gas-diffusion rates of H2 and H2O, and enlarging the effective reaction zone at the CL. The optimum CCL thickness was found to be 5 μm. The IR-free overpotentials η at the optimized DL hydrogen electrode in humidified hydrogen (p[H2O] = 0.4 atm) and Tcell = 800°C were 0.20 and −0.20 V at j = 0.5 and −0.5 A cm−2, respectively, indicating a highly reversible operation. The use of a full cell with the configuration of Ni0.9Co0.1/SDC DL hydrogen electrode|YSZ electrolyte|SDC interlayer|LSCF−SDC O2 electrode led to very promising results for the SOEC operation in which an IR-free electrolytic cell potential of 1.21 V at j = −0.5 A cm−2 and 800°C was achieved.
F895
The following article is Open access
W. Xu, G. M. Haarberg, S. Sunde, F. Seland, A. P. Ratvik, E. Zimmerman, T. Shimamune, J. Gustavsson and T. Åkre
In this work, commercial IrO2-Ta2O5 anodes with a certain composition calcined at three different temperatures were investigated. The results show that the calcination temperature has a significant influence on the electrocatalytic activity for the oxygen evolution reaction (OER). This is attributed to the influence of the calcination temperature on the surface microstructure including the crystallinity and the preferred orientation of IrO2 crystallites of the IrO2-Ta2O5 binary oxide formed. The surface morphology of the anodes was revealed as mud-cracks surrounded by flat areas containing several scattered IrO2 nanocrystallites. The size of these nanocrystallites, which in turn contribute to the electrochemical active surface area, is dependent on calcination temperature. The (101)-surfaces of the IrO2 were found to have higher catalytic activity than (110) IrO2 with respect to the OER. The (101) IrO2 planes were dominating at low or moderate calcination temperatures, whereas the (110) IrO2 orientation was preferred at the highest calcination temperature. Accelerated lifetime tests of the investigated samples indicate that the (101) IrO2 is more stable (110) IrO2 during electrolysis. A moderate temperature is suggested as the best calcination temperature for this type of anode regarding the electrochemical active surface area, electrocatalytic activity and stability for OER in acidic aqueous electrolytes at operating conditions.
F901
Andrew G. Star and Thomas F. Fuller
Extensive corrosion has been shown to result in collapse of the porous cathode microstructure in PEMFCs and has been presumed responsible for severe mass-transport voltage losses observed in polarization data. Corrosion of the carbon support was studied by electrochemical methods, non-dispersive infrared spectroscopy, and FIB-SEM tomography to evaluate the connected roles of carbon loss, microstructure, and performance degradation. In silico characterization of the three-dimensional, digital microstructures generated by FIB-SEM included porosity, Dijkstra tortuosity, and two-point correlation functions before and after corrosion. Carbon loss and H2/air operando performance decay were strongly correlated but contrary to expectation, the associated porosity loss and tortuosity gain did not explain the observed performance decay; cell failure occurred long before microstructural collapse was observed. Platinum catalyst ripening and preferential corrosion of the amorphous interior of carbon black primary particles were likely the two predominant degradation mechanisms induced among the cells tested. These results connect and clarify the roles of performance, microstructure, and corrosion degradation and demonstrate that microstructural collapse need not underlie cell failure.
F908
The following article is Open access
N. Todoroki, Y. Bando, Y. Tani, S. Kaneko, H. Watanabe, S. Takahashi and T. Wadayama
We investigated the electrochemical stability of a Pt/Pd(111) model core–shell structure for oxygen reduction reaction catalysts in 0.1 M HClO4 at 80°C by performing potential cycles (PCs) between 0.6 and x V vs. RHE (x = 0.8–1.0; xV-PCs). Pristine Pt/Pd(111) shows an ORR activity four times higher than that of Pt(111), which considerably decreased after 5000 cycles of 0.9- and 1.0 V-PCs and remained nearly unchanged for the 0.8- and 0.85 V-PCs samples. These results suggest that the atomic-scale structural changes at the Pt/Pd interface that depend on PC windows determine the durability of Pd–Pt core–shell structures.
F911
The following article is Open access
Andrei Kulikovsky
We report a physics-based analytical model for low-current PEM fuel cell impedance, which takes into account oxygen transport in the channel. The model is fast: fitting the model impedance to the experimental Nyquist spectrum takes about 2 minutes on a 2-GHz notebook. In addition to the transport and kinetic parameters of the catalyst layer, fitting returns the oxygen diffusion coefficient in the gas-diffusion layer and the resistivity due to oxygen transport in the channel. Maple worksheet with the fitting procedure is available for download.
F916
Shiyue Zhu, Dong Ding, Mei Li and Changrong Xia
Strontium doped lanthanum chromium manganite (LSCM) is a potential ceramic anode material for next-generation hydrocarbon-fueled solid oxide fuel cells. Because of its relatively low electrochemical performance, however, its application is still limited. This work investigated the effect of samaria-doped ceria (SDC) impregnation on the electrode performance regarding the surface reaction and oxygen-ion transport in the electrode reaction. The results showed that the electrochemical performance had been promoted by incorporating with nano-SDC particles. Electrical conductivity relaxation (ECR) of dense LSCM exhibited significant improvement in the surface exchange coefficient, from 5.34 × 10−6 cm s−1 at 850°C for bare LSCM to 1.48 × 10−4 cm s−1 for LSCM coated with 0.9 mol L−1 SDC precursor solution. The surface reaction promotion factor was about 28 for the nano SDC particle coating, much higher than the factor of 6.5 for LSCM-SDC composite. It was demonstrated that the promotion in surface reaction rate are mainly contributed by LSCM-SDC-gas three-phase boundaries (3PB). Interfacial polarization resistances of SDC impregnated LSCM symmetrical cells presented over 1 order of magnitude reduction at 850°C with a SDC loading of 35.8 wt%. The electrode performance improvement was attributed to the connective oxygen ion conduction path and increased 3PB formed by the impregnated SDC particles.
F923
Heng Zhong, Katsushi Fujii and Yoshiaki Nakano
Recently, extensive investigations have been carried out on the electrochemical and photoelectrochemical reductions of CO2 into hydrocarbons to convert renewable energies into chemical fuels. In these researches, aqueous solutions of bicarbonate salts, such as NaHCO3 and KHCO3, are widely used as the supporting electrolyte. However, the effects of HCO3− on the CO2 reduction have not been studied in detail. In this research, the effects of KHCO3 concentration on CO2 reduction were studied at different applied potentials on a Cu working electrode using a potentiostatic method. The concentration of dissolved CO2 ([CO2]) and ratio of [CO2]/[K+] in the KHCO3 solution after bubbling with CO2 were studied to determine the relationship between KHCO3 concentration and CO2 reduction faradaic efficiency. The results suggest that high [CO2]/[K+] ratio in solutions with low KHCO3 concentration is probably a key factor to promote CO2 reduction faradaic efficiency. A model for the effect of [CO2]/[K+] ratio on CO2 reduction efficiency was also proposed.
F928
The following article is Open access
M. Okumura, Z. Noda, J. Matsuda, Y. Tachikawa, M. Nishihara, S. M. Lyth, A. Hayashi and K. Sasaki
The cathode electrocatalyst layers of polymer electrolyte membrane fuel cells (PEFCs) are quantitatively investigated for different ratios of Nafion ionomer. This is achieved using focused-ion-beam coupled scanning electron microscopy (FIB-SEM) to reconstruct the three-dimensional microstructure via tomography. Parameters such as the porosity and pore size distribution were calculated from this data. The distributions of Nafion ionomer, carbon support, and platinum nanoparticles were then further clarified using transmission electron microscopy (TEM). Changes in the PEFC performance (notably the I-V characteristics, the electrochemical surface area, the activation overvoltage, and the concentration overvoltage) are thus correlated to electrode microstructure.
F935
The following article is Open access
Jingyi Chen, Antonio Bertei, Enrique Ruiz-Trejo, Alan Atkinson and Nigel P. Brandon
This study investigates the stability of nickel-impregnated scandia-stabilize zirconia composite electrodes during isothermal annealing at temperatures from 600 to 950°C in a humidified hydrogen atmosphere (3 vol % water vapor). Typically an initial rapid degradation of the electrode during the first 17 h of annealing is revealed by both an increase in polarization resistance and a fall in electronic conductivity. Secondary electron images show a shift in nickel particle size toward larger values after 50 h of annealing. The declining electrochemical performance is hence attributed to nickel coarsening at elevated temperatures. Nickel coarsening has two microstructural effects: breaking up nickel percolation; and reducing the density of triple phase boundaries. Their impact on electrode area specific resistance is explored using a physical model of electrode performance which relates the macroscopic electrochemical performance to measurable microstructural parameters.
F944
The following article is Open access
Hideaki Ohno, Shinji Nohara, Katsuyoshi Kakinuma, Makoto Uchida, Akiko Miyake, Shigehito Deki and Hiroyuki Uchida
In order to reduce the amount of noble metal catalysts for the oxygen evolution reaction (OER) in polymer electrolyte membrane water electrolysis (PEMWE) while maintaining high efficiency, we synthesized new catalysts: IrOx nanoparticles dispersed on Nb-SnO2 and Ta-SnO2 supports with fused-aggregate structures. IrOx nanoparticles with a uniform size of ca. 2 nm were highly dispersed on these supports. The OER activities were evaluated by linear sweep voltammetry (LSV) in 0.1 M HClO4 at 80°C using a channel flow electrode cell. The IrOx/Ta-SnO2 catalysts exhibited an apparent mass activity (MA) of 15 A mgIr−1 for the OER at 1.5 V vs. RHE, which was 32 times higher than that of a conventional catalyst (mixture of Pt black and IrO2 powders). This suggests a possible reduction of the loading of the noble metal anode catalyst to a level as low as 0.1 mg cm−2 at a voltage efficiency of 90% at 1 A cm−2.
F948
The following article is Open access
Vassili P. Glibin and Jean-Pol Dodelet
Two types of Fe-based catalytic sites have been proposed in the literature to perform the oxygen reduction reaction in PEM fuel cells running with FeN4-based electrocatalysts: [FeN4/C] or [FeN4C12] derived from the molecular structure of iron-porphyrin, and [FeN2+2/C], derived from the structure of the iron complex with two phenanthroline molecules. The energetics and chemical thermodynamic stability (equilibrium constants, Kc, for iron acid leaching) of these two types of sites and some of their oxygenated forms have been determined at pH ∼ 0. This does not consider the direct or indirect electrochemical oxidation of these catalytic sites or the electro-corrosion of their support. All evaluated FeN4-based sites are chemically stable in acid at both 298 and 353 K. It is their high values of TΔS contribution to the Gibbs free energy for acid leaching which are responsible for the stability of these catalytic sites. The dioxygen and hydroxyl complexes of [FeN4C12] and [FeN2+2/C] electrocatalysts demonstrate an improved stability with increasing temperature, explained by their electron withdrawing properties and their effect on the number of electrons in the antibonding orbitals. Complexes with dioxygen are more resistant to the action of acid than the ones formed by chemisorption of OH-groups.
F958
Yumao Kang, Wei Wang, Jinmei Li, Qinling Li, Shijia Liu and Ziqiang Lei
Developing efficient electrocatalysts for direct ammonia fuel cells has been researched intensively. Herein, a Pt-NiO/C catalyst is prepared and applied to ammonia oxidation reaction (AOR). The introduction of NiO can decrease the average crystallite sizes and modify the electronic structure of Pt. Compared with Pt/C catalyst, as-prepared Pt-NiO/C presents the larger electrochemical surface area (ECSA), higher peak current density, lower activation energy and better stability for AOR. It suggests that Pt-NiO/C is a promising system for AOR in direct ammonia fuel cells.
F966
The following article is Open access
Hiroshi Yano, Ikkei Arima, Masahiro Watanabe, Akihiro Iiyama and Hiroyuki Uchida
We have succeeded in preparing ordered- and disordered-Pt3Co nanoparticles supported on carbon black (CB), with the nearly identical particle size distribution, by the nanocapsule method with heat-treatment at high temperatures. The temperature dependences of the oxygen reduction reaction (ORR) activities at two kinds of Pt3Co/CB catalysts were examined in O2-saturated 0.1 M HClO4 solution by the multi-channel flow double electrode (M-CFDE) technique. For the ordered-Pt3Co/CB, the apparent rate constant kapp (per unit active area) for the ORR increased with elevation of the temperature up to 65°C and stabilized at nearly the same value as that for commercial c-Pt/CB at 80°C, due to a severe dealloying of the Co component in the hot acid solution. In contrast, the kapp values at the disordered-Pt3Co/CB were higher than those of the ordered-Pt3Co/CB over the whole temperature range from 30°C to 80°C. The disordered-Pt3Co/CB also exhibited higher stability than the ordered-Pt3Co/CB for both an accelerated durability test (ADT, by standard potential step cycles between 0.6 V and 1.0 V) in N2-purged 0.1 M HClO4 solution at 65°C and a corrosion test in air-saturated 0.1 M HClO4 solution at 65°C and 80°C.
F973
The following article is Open access
Michel Suermann, Kazuhiro Takanohashi, Adrien Lamibrac, Thomas J. Schmidt and Felix N. Büchi
Three different porous transport layer (PTL) structures, based on titanium sintered powders, were characterized using X-ray tomographic microscopy to determine key geometric properties such as porosity, pore and particle size distributions as well as effective transport properties. The mass transport through the PTL contributes to the voltage losses in the polymer electrolyte water electrolysis cell. Therefore, influence of the PTL structure on the mass transport overpotential is investigated as function of current densities (≤ 4 A·cm−2), operating pressures (1–100 bar) and temperatures (40–60°C), respectively. A decrease of transport losses was observed with increasing pressure and temperature for all investigated PTLs. At around 100 bar balanced pressure, the transport losses for all PTLs converge to about 40 mV per applied A·cm−2, suggesting that other parts of the cell such as the catalyst layer or their interface contribute to these remaining losses. The performance loss, induced by the different PTL structures, shows a stronger correlation with geometric parameters such as pore and particle size distributions than transport properties like effective diffusivity and permeability. The finest materials with d50 pore and particle diameters of 40–48 and 68 μm, respectively, are performing better than the coarsest material with diameters roughly twice the sizes.
F981
Peng Qiu, Jin Li, Bo Liu, Lichao Jia, Bo Chi, Jian Pu and Jian Li
The La0.8Sr0.2MnO3-δ (LSM)-coated Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF) cathode with 3D core-shell architecture has been fabricated by the solution impregnation technology. On the basis of previous research, the synthetic process is improved in order to promote the perovskite degree of BSCF. In this paper, the oxygen reduction reaction (ORR) mechanism of LSM-coated BSCF is studied in detail. As the intervention of LSM shell, the LSM-coated BSCF presents the different ORR rate-determining step comparing with the BSCF cathode. The formation and transfer of lattice oxygen in LSM is the rate-determining step for the LSM-coated BSCF cathode, while the molecular oxygen surface adsorption for the BSCF cathode. In the single cells test, the LSM-coated BSCF cell shows a higher maximum power density than the uncoated cell. The remarkable CO2-poisoning resistant performance of LSM-coated BSCF is verified by the CO2-TPD test and the single cell potentiostatic test. The excellent electrochemical performance and CO2-poisoning resistance indicate that LSM-coated BSCF cathode appears to be a promising cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs).
F988
M. Marrony and J. Dailly
Ba-based protonic ceramic cell (PCC) was investigated under galvanostatic electrolysis and reversible Fuel cell/electrolysis cycles modes. Such PCC has been made by industrial wet chemical routes (tape casting and screen-printing methods) and by using NiO-BaCe0.8Zr0.1Y0.1O3-δ (BCZY81) as anode/BCZY81–ZnO (5 mol%) as electrolyte, Ba0.5Sr0.5Co0.8Fe0.2O3-δ (BSCF) – BCZY81) as air electrode and BSCF as current collector. The optimization of key parameters of both fuel cell and electrolysis operating conditions such as water feed content, fuel utilization, temperature operation allow to validating promising electrical cell performances (>0.25 W/cm², 0.7 V under fuel cell mode; 0.5 A/cm², 1.3 V under electrolysis mode) and reliability during more than 3500 h with limited electrical degradation (<2%/kh) at 700°C. The evolution of Electrochemical Impedance Spectroscopy measurements reveals that the total electrical resistances of PCC are lower under electrolysis than under fuel cell mode, in particular the ohmic resistance (electrolyte). But in the same time, the polarization resistance of the cell (air electrode interface) is higher under electrolysis mode. The combination of high temperature and water vapor pressure can induce negative reaction able to accelerate the Ba-based materials aging. In any case, it highlights the use of PCC technology as high efficient energy storage candidate.
F995
The following article is Open access
Dana Schonvogel, Julia Hülstede, Peter Wagner, Ivar Kruusenberg, Kaido Tammeveski, Alexander Dyck, Carsten Agert and Michael Wark
Pt supported on carbon black, commonly used as PEM fuel cell catalyst, underlies electrochemical instabilities in terms of carbon corrosion and platinum degradation. To better understand the influence of the support on nature and extent of catalyst aging, Pt was synthesized on four different substrates: Carbon black, multiwalled carbon nanotubes (MWCNTs), reduced graphene oxide (rGO) and a nanocomposite of indium tin oxide with rGO (ITO-rGO). The four Pt catalysts and the separate supports were studied on their durability using an accelerated stress test (AST, −0.02–1.40 VSHE). Comparable platinum degradation was shown by losses of electrochemically active surface area (EASA) and activity for oxygen reduction reaction (ORR) and by identical location transmission electron microscopy (IL-TEM). With respect to the supports, highest instability of carbon black was observed investigating the double layer capacitance and amounts of hydroquinone (HQ) species. MWCNTs showed the lowest degradation. Thus, AST provoked strongly different extents of support aging but similar Pt degradation. In view of complex FC catalyst degradation mechanism, only negligible Pt detachment caused by support degradation and rather dominating Pt dissolution and agglomeration—additionally evidenced by IL-TEM—is assumed here. Regarding ITO-rGO, neither carbon support nor platinum stabilization by ITO nanoparticles has been observed.
F1005
M. Chen, H. Alimadadi, S. Molin, L. Zhang, N. Ta, P. V. Hendriksen, R. Kiebach and Y. Du
Ferritic stainless steel interconnect plates are widely used in planar solid oxide fuel cell and electrolysis cell stacks. During stack production and operation, nickel from the Ni/yttria stabilized zirconia fuel electrode or from the Ni contact component layer diffuses into the interconnect plate, causing transformation of the ferritic phase into an austenitic phase in the interface region. This is accompanied with changes in volume, and in mechanical and corrosion properties of the interconnect plates. In this work, kinetic modeling of the inter-diffusion between Ni and FeCr based ferritic stainless steel was conducted, using the CALPHAD (CALculation of PHAse Diagrams) approach with the DICTRA (DIffusion Controlled TRAnsformation) software. The kinetics of inter-diffusion and austenite formation was explored in detail. The simulation was further validated by comparing with experiments. The results show that after 2000 h at 800°C Ni diffuses more than 100 μm deep into Crofer 22 APU. Along with the Ni diffusion, part of the ferritic steel with 50–60 μm in thickness has transformed into the austenitic phase. Growth of the austenite phase in commercial interconnect materials was predicted to take place under practical stack operation conditions.
F1011
The following article is Open access
Phuong Tu Mai, Masanobu Chiku, Eiji Higuchi and Hiroshi Inoue
We demonstrated that the controlled Rh deposition was important for improving the selectivity for CO2 formation at a SnO2-modified Pt (Pt/SnO2) electrode, which mainly produced acetic acid in electrochemical ethanol oxidation reduction (EOR). The limited CO stripping technique was used for preferentially depositing Rh atoms on the Pt atoms adjacent to Sn atoms. The resultant Rh-modified Pt/SnO2 electrode increased the catalytic activity for EOR by about 4 times compared to the Pt electrode, and also greatly improved the CO2 selectivity.
F1014
The following article is Open access
Sajid Hussain, Heiki Erikson, Nadezda Kongi, Maido Merisalu, Mihkel Rähn, Väino Sammelselg, Gilberto Maia and Kaido Tammeveski
Platinum nanoparticles supported on multiwalled carbon nanotubes (Pt/MWCNT) were prepared using controlled electrochemical deposition from Ar-saturated H2PtCl6 solution. The electrodeposition parameters were varied to observe change in the surface morphology and electrocatalytic activity of the Pt/MWCNT catalysts for oxygen reduction reaction (ORR). Surface morphology of the prepared catalysts was studied by scanning electron microscope (SEM) and scanning transmission electron microscope (STEM). For electrochemical characterization of the Pt/MWCNT electrocatalysts, CO-stripping and cyclic voltammetry (CV) experiments were performed in 0.05 M H2SO4 solution. The ORR was studied in acid medium using the rotating disk electrode (RDE) method. The results obtained were analyzed and compared to those of commercial Pt/C. The size, shape and distribution of Pt particles as well as the electrochemical behavior of Pt/MWCNT modified electrodes showed strong dependence on the deposition parameters. The catalyst materials prepared by electrochemical deposition showed higher specific activities than commercial Pt/C catalyst. The Pt/MWCNT cathode materials showed remarkable stability during repetitive potential cycling in 0.05 M H2SO4.
F1022
Anjaiah Sheelam and Kothandaraman Ramanujam
Recently, pyrolyzed transition metal-carbon-nitrogen based non-precious metal (NPM) catalysts are envisioned as promising alternatives to metal catalysts. However, the precise active site in these NPM catalysts remains elusive, as their surface composition is heterogeneous in nature. Lack of understanding on the electrocatalytic active site for the oxygen reduction reaction (ORR) is one of the fundamental obstacles in design and synthesis of the catalyst. In this study, carbon supported metal–organic complexes,[Co(bpy)3](NO3)2 and [Co(bpy)2NO3]NO3 · 5H2O (where, bpy is 2,2’-Bipyridine) are shown to perform ORR in 0.1 N KOH. Replacement of one of the bipyridine of [Co(bpy)3]2 + with NO−3, yields a catalyst, [Co(bpy)2NO3]+ with improved ORR kinetics. The NO−3 ligand influence on the reduction of the oxygen studied using the linear sweep voltammograms obtained using rotating disc electrode, rotating ring-disc electrode and Tafel analysis. The Tafel slope and exchange current density measured on [Co(bpy)2NO3]NO3 · 5H2O and [Co(bpy)3](NO3)2 are 105 mV dec−1, 2 × 10−4 mA cm−2 and 120 mV dec−1, 4 × 10−4 mA cm−2 respectively. Turn-over frequency (ToF) of these complexes estimated to understand the extent of selectivity of these complexes toward 2- and 4-electron reduction of O2.
F1030
Pankaj Kr. Tiwari, Xiangling Yue, John T. S. Irvine and Suddhasatwa Basu
Nickel-yttria stabilized zirconia (Ni-YSZ) cermet anodes for solid oxide fuel cells (SOFC) possesses excellent catalytic properties and stability for H2 oxidation but not for hydrocarbons as it results in fast carbon deposition in absence of excess steam. In the present work, A-site deficient porous LSCTA- (La0.2Sr0.25Ca0.45TiO3) anode has been fabricated using the environment friendly, aqueous tape casting method followed by the same procedure for the dense YSZ electrolyte and YSZ porous scaffold as cathode matrix. The anode, electrolyte, and porous cathode matrix have been laminated together and sintered up to 1350°C. After sintering, nitrate precursors of La, Sr, Co and Fe are infiltrated inside the porous YSZ cathode matrix to form the perovskite phases of La0.8Sr0.2CoO3 (LSC) and La0.8Sr0.2FeO3 (LSF). The as fabricated electrolyte supported SOFCs have been tested in H2 and CH4 fuel at 800°C. The electrolyte supported cell 15%LSF-5% LSC-YSZ/YSZ/4%Ni-6%CeO2-LSCTA- gives maximum power density of 328 mW cm−2 for 3 h in H2, but in CH4 the performance decreased to 165 mW cm−2 even though a sustained open circuit voltage of ∼1 V obtained during H2 and CH4 operation. The morphology of the anode before and after cell testing has been analyzed using scanning electron microscope followed by X-ray diffraction studies to understand phase changes during fabrication and testing.
F1037
The following article is Open access
S. Komini Babu, H. T. Chung, P. Zelenay and S. Litster
This paper presents a two-dimensional (2D) computational model of a polymer electrolyte fuel cell (PEFC) with a platinum group metal-free (PGM-free) catalyst cathode that can significantly reduce PEFC costs by eliminating the need for expensive platinum catalysts. Due to their comparatively low volumetric activity, PGM-free cathodes are an order of magnitude thicker than their Pt-based counterpart. The resulting need for greater electrode thickness to achieve sufficient power density requires careful attention to the transport losses across the thicker cathodes. The presented model is used to correlate the composition and morphology of the cathode to PEFC performance. The model is a complete cell, continuum model that includes an advanced agglomerate model for a microstructurally consistent representation of the cathode. A unique feature of the approach is the integration of morphology and transport parameter statistics extracted from nano-scale resolution X-ray computed tomography (nano-CT) imaging of PGM-free cathodes. The model was validated with experimental results of PGM-free cathodes with varying Nafion loading. Our key findings are a need for increased cathode hydrophobicity and increased ionomer conductivity through either reduced tortuosity or increased bulk conductivity. We further use the model to evaluate targets for the volumetric activity and active site density for future catalysts.
Organic and Bioelectrochemistry
G87
Safoura Bakhtiari Haft Lang, Davood Nematollahi, Ahmad Reza Massah, Mahnaz Sharafi-Kolkeshvandi and Hojjat Alizadeh
The electrochemical behavior of 1,5-diaminonaphthalene (1,5DAN) was studied by cyclic voltammetry and controlled-potential coulometry methods in aqueous ethanol (water/ethanol, 70/30 v/v). The effect of different parameters such as solution pH (from 2 to 10), potential scan rate and 1,5DAN concentration on its electrochemical behavior was studied. The electrochemical synthesis of 4-imino-4H-dibenzo[a,h]phenoxazin-11-ol (IDP) was achieved in high yield (87%) by electrooxidation in water (bicarbonate buffer, c = 0.2 M, pH = 9.0)/ethanol (70/30, v/v) in a one-pot process. The proposed mechanism involves the Michael addition of 1,5DAN to 1,5-naphthalendione (from the hydrolysis of the electrogenerated naphthalene-1,5-diimine (1,5DANox)) followed by oxidation of the 1,5-diaminonaphthalene moiety, cyclization, aromatization, and a final oxidation. Polymerization of 1,5DAN was not observed. The present work provides a green and environmentally friendly method with high atom economy for the synthesis of IDP in an undivided cell under constant current. In addition, IDP showed antibacterial activity against Gram-positive bacteria Bacillus cereus and Staphylococcus aureus.
G92
Anahita Karimi and Silvana Andreescu
A hybrid CeO2-based biocatalytic nanostructure carrying catalytically active oxygen-rich nanoparticles is described as a general platform for laccase (Lac)-based biocathodes and biofuel cells. To design the bioelectrodes, the particles and the enzyme were deposited on reduced graphene or carbon nanotube-based buckypaper using conducting poly(3,4-ethylenedioxythiophene):poly-styrene-sulfonic acid (PEDOT:PSS). The use of CeO2 into the biocatalytic layer enhanced the bioelectrocatalytic reduction current and enabled functionality of the bioelectrode and biofuel cell in oxygen-limited conditions. These results open up new avenues for designing biointerfaces for protecting activity of immobilized enzymes and providing functionality in oxygen-limited environments. The hybrid nanostructure described in this work may be used as a general platform for the immobilization of other enzymes for a variety of biosensing, biofuel cells and bioelectronics applications.
G99
The following article is Open access
Mehrdad Balandeh, Christopher Waldmann, Daniela Shirazi, Adrian Gomez, Alejandra Rios, Nathanael Allison, Asad Khan and Saman Sadeghi
Electrochemical fluorination of methyl(phenylthio)acetate was achieved using tetrabutylammonium fluoride (TBAF). Electrochemical fluorination was performed under potentiostatic anodic oxidation using an undivided cell in acetonitrile containing TBAF and triflic acid. The influence of several parameters including: oxidation potential, time, temperature, sonication, TBAF concentration and triflic acid concentration on fluorination efficiency were studied. It was found that the triflic acid to TBAF concentration ratio plays a key role in the fluorination efficiency. Electrochemical fluorination resulted in formation of mono-fluorinated methyl 2-fluoro-2-(phenylthio)acetate verified by gas chromatography–mass spectrometry (GC-MS) and nuclear magnetic resonance (NMR) Spectroscopy. Under optimum conditions 44 ± 3% mono fluorination yield was obtained after a 30 min electrolysis. Electrochemical radiofluorination for the synthesis of methyl 2-[18F]fluoro-2-(phenothio) acetate was also achieved with the same optimized electrochemical cell parameters where TBAF was first passed through an anion exchange resin containing fluorine-18. A radiochemical fluorination efficiency of 7 ± 1% was achieved after 30 min of electrolysis.
Physical and Analytical Electrochemistry, Electrocatalysis, and Photoelectrochemistry
H551
The following article is Open access
Ruttala Devivaraprasad, Tathagata Kar, Pradipkumar Leuaa and Manoj Neergat
The interaction of halide ions (I−, Br−, Cl−) with well-cleaned faceted platinum (nanocube, cuboctahedral) nanoparticles and platinum polycrystalline is investigated in 0.5 M H2SO4 electrolyte. Under electrochemical conditions, the Pt surface gets poisoned with halide ad-atoms and it causes the attenuation of both hydrogen adsorption/desorption in the lower potential region (0.06–0.4 V) and electroxidation of Pt nanoparticles in the higher potential region (0.6–1.2 V). Above certain concentration (5 × 10−6 M), the strongly adsorbing I− ions mask the Hupd features. On the other hand, Br− and Cl− ions alter the peak features in the Hupd region, those are characteristic of different Pt surface sites. On excursion to higher potentials (∼>1.2 V), concurrent halogen evolution, Pt oxidation, and oxygen evolution are observed; the increase in peak intensity in the Hupd region reflects the reconstruction of the Pt surface. To remove the adsorbed halide ions from the Pt surface, an in-situ potentiostatic method is employed, which involves holding the working electrode at ∼0.03 V in 0.1 M NaOH solution. The cleanliness and retention of surface-structure are confirmed from the voltammograms recorded in the test electrolyte and the recovery of oxygen reduction reaction (ORR) activity after cleaning the Br− ion-contaminated Pt surface supports this conjecture.
H561
K. Selvarani and Sheela Berchmans
The electrocatalytic properties of the redox couple Ni(OH)2/NiOOH at physiological pH was investigated in the presence of cationic polymeric films providing alkaline microenvironments, with the objective of developing a biosensor for cholesterol and glucose. The Ni(OH)2/NiOOH modified electrodes in presence of the cationic polymer overlayers were well characterized by optical and electrochemical techniques. The modified electrodes showed excellent catalytic properties toward hydrogen peroxide oxidation and exhibited a wide linear range compared to the conventional and expensive Pt based catalysts used in H2O2 based sensors. The superb electrocatalysis of hydrogen peroxide could be combined with the enzymatic oxidation of cholesterol and glucose showing, the feasibility of monitoring biological metabolites like glucose and cholesterol using the basic catalyst Ni(OH)2/NiOOH at physiological pH. Modified electrodes were highly stable and yielded reproducible results. Further the influence of graphene layer in decreasing the overpotential of the detection of H2O2 and its effect on the biosensing of cholesterol and glucose was further investigated. The sensing protocol was validated in the analysis of blood sugar in serum samples.
H572
Jing Zhang, Xinhe Song, Zhanbing Xiong, Haifeng Dong, Wenchang Wang and Zhidong Chen
This work designed an ultrasensitive electrochemical immunosensor for Escherichia coli O157:H7 (E. coli O157:H7) detection using carbon nanohorns as immobilization scaffold and nanogold/Bi2S3 nanorods (Au/Bi2S3NRs) as a signal tag to catalyze silver deposition for signal amplification. Au/Bi2S3NRs prepared by in situ growth of nanogold on Bi2S3 nanorods was used as a tracing tag to label signal antibody, which induced silver deposition for anodicstripping analysis. The immunosensor was constructed by immobilizing capture antibody on carbon nanohorns modified electrode with the aid of polyethylene glycol film. Through a sandwich-type immunoreaction, Au/Bi2S3NRs tags were captured on the immunoconjugates to induce a silver deposition process. The electrochemical stripping signal of the deposited silver was used to monitor the immunoreaction. The Au/Bi2S3NRs-mediated silver enhancement along with the carbon nanohorns-promoted electron transfer led to high detection sensitivity of E. coli O157:H7 antigen. Under the optimal conditions, the immunosensor exhibited a wide linear dependence on the logarithm of the concentration of E. coli ranging from 40 to 2.0 × 106 cfu mL−1 with a detection limit of 6 cfu mL−1. Moreover, the proposed sensor was successfully applied in the detection of E. coli O157:H7 in real samples indicating its possibility in practical application.
H579
The following article is Open access
Yongcong Wang, Haitao Han, Dawei Pan and Peiqing Zhang
In this work, cobalt-doped Fe2O2CO3-reduced graphene oxide (Co@Fe2O2CO3-rGO) nanocomposites were synthesized by using one-step electrodeposition. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction spectroscopy (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical methods were used to characterize the nanocomposites. The results showed that the Co@Fe2O2CO3 nanoparticles with average 20–40 nm were anchored on the rGO film tightly and the resulting nanocomposites showed excellent electro-catalytic effect toward the reduction of hydrogen peroxide. The determination of hydrogen peroxide was successfully achieved in the high salinity solution (0.5 mol L−1 NaCl) and the calibration curve was observed in the range of 1.5–956 μmol L−1 with the limit of quantitation of 1.5 μmol L−1 and the limit of detection of 0.4 μmol L−1.
H584
The following article is Open access
Iwao Mogi, Masakazu Iwasaka, Ryoichi Aogaki and Kohki Takahashi
Using guanine micro-crystals with light-reflective surfaces as a fluid tracer, magnetohydrodynamic (MHD) flows were visualized in silver electrodeposition under a magnetic field of 2 T. The trace of a guanine particle showed macroscopic MHD laminar flows at a low deposition current of 50 μA. On the contrary, at a high current of 200 μA, the trace exhibited a zigzag walk and vortex motion with the sizes of 100 ∼ 500 μm. This behavior demonstrates the existence of micro-MHD vortices that play a crucial role in chiral surface formation.
H587
Jingjing Bai, Qiangqiang Sun, Zenglin Wang and Chuan Zhao
It is challenging but imperative to develop highly efficient, low-cost and environmentally friendly electrocatalysts to produce H2 fuel through water splitting. In order to improve the electrochemical performance of Co-base catalyst for hydrogen evolution reaction (HER), nanoporous cobalt nickel hydroxide (CoNi) composites were fabricated on the 3D nickel foam (NF) by a cyclic voltammetry method. With a doping of nickel hydroxide, the electrocatalytic activity of the catalysts was significantly enhanced. As-prepared optimal CoNi/NF electrode is able to deliver a current density of 10 mA/cm2 with an overpotential (η) of only 77 mV, which is much lower than of Co/NF electrode (185.5 mV) and Ni/NF electrode (189 mV), and shows exceeding stability and durability. The CoNi/NF catalyst also displays extraordinary performance at high current densities (e.g., 200 mA/cm2 at η = 204 mV), and is comparable to the best Co-based HER electrocatalysts reported to date. The high active surface areas (about 14 times higher than the bare NF), high surface wettability and low charge-transfer resistance of CoNi/NF catalyst, together with effective mass transport offered by the 3D nanoporous structure, all contribute to the extraordinary synergistic HER performance.
H593
Jerónimo Agrisuelas, Alejandro Cuenca, Antonello Frau, David Ferrús, José Juan García-Jareño, Roger Sanchis-Gual and Francisco Vicente
Electropolymerization of Azure A on indium-tin oxide (ITO) and gold electrodes have been carried out from KNO3 aqueous solution. After repetitive voltammetry cycles (electrochemical ageing process), surface morphology of the resulting film is altered involving a deactivation of its pristine electroactivity. Aged and pristine PAA films have been characterized by hyphenated techniques based on spectroelectrochemistry and electrogravimetry (cyclic voltammetry, electrochemical quartz crystal microbalance, and Vis-NIR spectroscopy). Correlation of these techniques allows to obtain the very subtle qualitative and quantitative difference between both films. Accumulation of hydrogen gas inside films is postulated to be the cause of the electrochemical deactivation. In addition, the electroactivity renovation by a soft thermal treatment in oven at 60°C during 24 h is evaluated.
H603
G. C. A. Ferreira, T. W. Napporn, K. B. Kokoh and H. Varela
The electrocatalytic oxidation of glucose is relevant from fundamental and applied, viz. fuel cell and sensors, perspectives. Understanding mechanistic details of this reaction is of paramount importance for further practical developments including the rational design of catalysts. In this article we present and discuss the, previously unreported, occurrence of oscillatory reaction rates during the electro-oxidation of D-(+)-glucose on polycrystalline gold, in alkaline medium. The system was studied by cyclic voltammetry, chrono-amperometry/potentiometry, and electrochemical impedance spectroscopy. Very rich dynamics under potentio- and galvanostatic regimes and in a wide parameter window was observed. Oscillations’ frequencies spanning four orders of magnitude and distinct amplitudes and potential windows characterized the dynamics. Mechanistic aspects as well as implications of oscillatory kinetics in energy conversion and sensing systems are also presented.
H608
The following article is Open access
Martin Ruge, Jakub Drnec, Björn Rahn, Finn Reikowski, David A. Harrington, Francesco Carlà, Roberto Felici, Jochim Stettner and Olaf M. Magnussen
The potential dependent surface structure of Pt(111) electrodes in electrochemical environment was studied by in situ crystal truncation rod measurements and in operando grazing incidence small angle X-ray scattering. Determination of the interface structure in the oxidation region reveal a continuous increase of the coverage of place exchanged atoms toward more positive potentials. The resulting oxide consists of an oxygen rich outer and a Pt-rich inner atomic layer. With increasing potential the oxide approaches a more uniform stoichometry. While place exchange on atomically smooth terraces only occurs above 1.05 V, structural changes of 3D Pt islands, grown by repetitive oxidation/reduction cycles, already commence at 0.8 V, which is assigned to oxidation at Pt steps. Evolution of the 3D island distribution occurs in all stages of the cycles: Whereas Pt oxidation leads to narrowing of the lateral size distribution, vertical island growth occurs during the subsequent reduction.
H615
The following article is Open access
Kaitlyn DeHority, Noah Budin, Samantha S. Hilston, Yongqian (Kelly) Zhang and Akiko Fillinger
Deposition of nickel on electrodeposited Cu2O films was investigated at potentials more positive than the estimated Nernst equilibrium potential of Ni2+/Ni0 for the purpose of developing a monolayer deposition method that will act as a protective and catalytic overlayer on the oxide films. Cu2O films were subjected to 0.08 mM nickel acetate solutions for 60 s at potentials more positive than the estimated Nernst equilibrium potential of Ni2+/Ni0. The quantities of Ni recovered from the Cu2O films were determined by atomic absorption spectrometry. The oxidation state of Ni deposited on the Cu2O was determined to be +3 via X-ray photoelectron spectroscopy. The absence of evidence of reduction of Ni2+ to Ni0 suggests that the nature of the nickel deposition is adsorption, and it is not characterized as underpotential deposition. Photoelectrochemical measurements showed that deposited Ni protected Cu2O films from the photodecomposition to Cu0 by interfering with H+ binding to the O2− surface sites, and indicated the possibility of catalytic activity of deposited nickel for H+ reduction. The catalytic activity of deposited nickel was explained by the shift of the Cu2O Fermi level by 50 mV in negative direction upon nickel deposition.
H621
The following article is Open access
K. Hedenstedt, J. Bäckström and E. Ahlberg
Water reduction on corroded iron surfaces is technologically and fundamentally important. Here, the technological interest originates from the chlorate process where water reduction is the main cathodic process. Fundamentally, water reduction on oxide surfaces raises questions on the stability of the oxide and the nature of electrocatalytic surface sites. Two iron oxyhydroxides, α- and γ-FeOOH, were electrodeposited on titanium substrate and their reduction processes were followed in detail with in-situ Raman spectroscopy, using low incident laser power to avoid sample damaging. Polarization to negative potentials show two reduction peaks for γ-FeOOH and one peak for α-FeOOH prior to hydrogen evolution. The characteristic Raman peaks gradually disappear as the potential is made more negative but no new peaks can be observed. δ-FeOOH was detected as an intermediate phase upon oxidation of the reduced surface layer. This indicates that Fe(OH)2 is formed during cathodic polarization and initially re-oxidized to the isostructural δ-FeOOH. Characteristic Raman signals of the original phases appear upon further oxidation in air.
H628
Mamdouh R. Rezk, Ahmed S. Fayed, Hoda M. Marzouk and Samah S. Abbas
The sustainable and green chemistry principles enable scientists to protect and benefit the economy, people and the planet by finding creative and innovative ways to reduce waste, conserve energy, and discover replacements for hazardous substances. In this work, an environmentally friendly ion selective electrode (ISE) potentiometric method was developed for the determination of cinchocaine hydrochloride (CIN) in presence of its degradation products either in bulk powder or in its combined pharmaceutical formulation with betametahsone valerate. Two novel CIN-selective electrodes were fabricated and evaluated. The fabrication of electrodes was based on sodium tetrakis [3,5-bis (trifluoromethyl)phenyl]borate as a cationic exchanger in a PVC matrix with 2-nitrophenyl octyl ether (2-NPOE) as a plasticizer and using 2-hydroxy propyl-β-cyclodextrin (2-HP β-CD) as an ionophore. A comparative study was conducted using two designed CIN-selective electrodes; a conventional liquid inner contact, sensor 1, and a glassy carbon solid contact electrode, sensor 2. Sensor 1 has a linear dynamic range of 3.0 × 10−5 mol L−1 to 1.0 × 10−2 mol L−1, with a Nernstian slope of 54.89 mV/decade and a detection limit of 5.01 × 10−6 mol/L. Sensor 2 shows linearity over the concentration range of 1.0 × 10−5 mol L−1 to 1.0 × 10−2 mol L−1, with a Nernstian slope of 57.01 mV/decade and a limit of detection of 2.51 × 10−6 mol L−1 which is much improved as a result of diminishing ion fluxes in this solid contact ion-selective electrode. The present electrodes show clear selectivity for CIN from several inorganic, structurally related organic molecules, sugars, co-formulated drug, some common drug excipients and its degradation products. The results obtained by the proposed sensors were statistically analyzed and compared with those obtained by official method. No significant difference for either accuracy or precision was observed.
H635
Rachel Guia P. Giron and Gregory S. Ferguson
The electrochemical oxidation of a gold electrode supported on an AT-cut quartz crystal in aqueous sulfuric acid resulted in formation of a thin film of gold oxide, and removal of the applied potential led to loss of the oxide. The piezoelectric substrate allowed in situ determination of changes in the potential and the mass of the electrode throughout both processes. Upon opening the circuit (OC), the electrode potential immediately dropped to that characteristic of Au/Au2O3 and remained there until the oxide had been lost. Electrochemical quartz-crystal microgravimetric (EQCM) measurements revealed that the resonant frequency of the crystal behaved similarly, quickly adjusting to a value consistent with approximately a nanometer of Au2O3 and then remaining approximately constant until both the potential and frequency adopted bare-gold values. Reduction of the oxide during the period of constant OC-potential and mass confirmed the onset of cathodic silence —inaccessibility of the oxide to reduction by an applied cathodic potential.
H639
Dhanjai and Ankita Sinha
This work reports potential application of nitrogen doped carbon nanotubes and chitosan nanocomposite modified glassy carbon electrode (N-CNTs-CHIT/GCE) nanosensor for amperometric characterization of antiulcer drug, rabeprazole (RB). Synthesized N-CNTs were characterized using microscopic and spectroscopic techniques like scanning electron microscopy (SEM), transmission electron microscopy (TEM), raman spectroscopy, X-ray diffraction (XRD) and energy dispersive X-ray analysis (EDAX). The fabricated N-CNTs-CHIT/GCE sensor showed superior electrocatalytic performance toward oxidation of RB. With highly conductive network, large electrocatalytic surface area and low charge transfer resistance, N-CNTs-CHIT/GCE sensor exhibited remarkable amperometric current-time response curves in 0.1% sodium dodecylbenzenesulfonate (SDBS) solubilized system minimizing the use of hazardous organic solvents during electroanalysis. The nanosensor was found to exert linear relationship between current and increasing concentration of RB with correlation coefficient (r2) of 0.9922 in wide concentration range of 100.0 ng mL−1–1.4 μg mL−1 exhibiting high reproducibility and good storage stability. The high recovery (89.33%–95.0%) of RB in commercial tablets suggests great applicability of N-CNTs-CHIT/GCE sensor for analytical purposes.
H647
Eduardo G. Machado, Marcelo V. F. Delmonde and Hamilton Varela
The electro-oxidation of formic acid on platinum electrodes has been on the spotlight for the last decade since it presents an apparent simple, yet intricate mechanism with three known reaction pathways. Despite the formation of CO, a strongly adsorbed intermediate, it was reported an interesting behavior when hydrazine is added in this solution. The simultaneous oxidation of formic acid and hydrazine was argued to be additive, meaning that both molecules would be oxidized without one interfering to the other. However, recently, it was suggested that this process would proceed synergistically. In this work, we aim at understanding how both molecules are oxidized on a platinum surface by monitoring the formation of gaseous products with Differential Electrochemical Mass Spectrometry (DEMS). The chosen pH was acidic (∼0.3) and the working electrode employed was a platinum sputtered Teflon membrane. The results showed that the signal of the ratio mass/charge 44 (related to CO2 production) for the formic acid and hydrazine system exhibited a new peak at lower potentials (c. a. 0.55 V), where the oxidation of formic acid would not proceed in the absence of hydrazine. The enhanced production of CO2 in the presence of hydrazine, which does not contain any carbon on its structure, yields the spectrometric proof that a more-than-additive mechanism takes place when oxidizing the mixture. These results open a new perspective for the study of the mechanism of the formic acid oxidation and to the development of new mixed fuels for energy conversion devices.
H651
Li Zhang, Wei Yu, Cui Han, Jiang Guo, Qinghong Zhang, Hongyong Xie, Qian Shao, Zhiguo Sun and Zhanhu Guo
Heterostructured TiO2/SnO2 fibrillar nanocomposites were synthesized by using electrospinning technology with the setup composed of a syringe pump with two parallel syringes on it and a rotating collector. The heterojunctions were formed between TiO2 and SnO2 nanofibers fast and efficiently on a large scale, after the fiberizing carrier polyvinylpyrrolidone (PVP) on the as-spun composite nanofibers was burnt away at 500°C. The samples were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflection spectroscopy (DRS), and photoluminescence spectra (PL), respectively. The results indicated that two kinds of small nanofibers with different diameters were interconnected to form heterojunctions. Photocatalytic tests displayed that the heterostructured TiO2/SnO2 nanofibers exhibited a much higher degradation rate of methylene blue (MB), rhodamine B (RhB), and 4-chlorophenol (4-CP) than that of bare TiO2 nanofibers or Evonik P25 under UV light irradiation. The enhanced photocatalytic activity could be attributed to the effective charge separation derived from the coupling effect of TiO2 and SnO2 nanocomposites.
H657
Manoj Kumar Sahani, A. K. Singh and A. K. Jain
Schiff base ligands 2,2′-(((ethane-1,2-diylbis(oxy))bis(2,1-phenylene))bis(methanylylidene))bis(hydrazinecarbothioamide) (L1), 2,2′-(((propane-1,3-diylbis(oxy))bis(2,1-phenylene))bis(methanylylidene))bis(hydrazinecarbothioamide) (L2) and 2,2′-((((oxybis(ethane-2,1-diyl))bis(oxy))bis(2,1-phenylene))bis(methanylylidene))bis(hydrazinecarbothioamide) (L3) have been synthesized and were explored as ion carrier in the construction of solid contact Zn2+ PVC based membrane sensor. The effect of plasticizers, benzylacetate (BA), dioctylphthalate (DOP), dibutylphthalate (DBP), 1-chloronaphthlene (1-CN) and o-nitro-phenyloctylether (o-NPOE) and anion excluders, sodium tetraphenylborate (NaTPB) and potassium tetrakis-p-(chlorophenyl)borate (KTpClPB) on the performance of the electrodes has also been investigated. Comparative studies performed on coated graphite electrode (CGE) and coated pyrolytic graphite electrode (CPGE) reveal the superiority of CPGE with optimized membrane composition of L2: PVC: DOP: NaTBP≡6:34:58:2 (w/w, mg) exhibits the best results with a wide working concentration range of 1.1 × 10−8–1.0 × 10−1 mol L−1, detection limit of 8.0 × 10−9 mol L−1, Nernstian slope of 29.6 ± 0.2 mV decade−1 of activity of Zn2+ ion in the pH range of 3.0–9.0. The sensor showed fast response time of 10 s and could be used over a period of 4 months without any significant divergence in slope, working concentration range and detection limit. The sensor was employed in the quantification of Zn2+ ion in various samples and also as an indicator electrode in the potentiometric titration of Zn2+ ion with EDTA.
H667
Olga A. Krysiak, Piotr J. Barczuk, Krzysztof Bienkowski, Tomasz Wojciechowski and Jan Augustynski
Suspensions of titanium dioxide catalysts decorated with plasmonic metal nanoparticles (NPs) are widely investigated in view of photodegradation of a variety of contaminants in water under irradiation with visible light. In this work, we used porous TiO2 electrodes bearing gold NPs to carry out photooxidation of model organic molecules either using oxygen as scavenger of photogenerated electrons or under imposed anodic bias. In both cases, continuous decrease of visible light photoactivity consistent with the drop of incident photon-to-current efficiencies (IPCEs) of the Au/TiO2 photocatalyst was observed.
H670
Kumi Naito, Yuri Maeda, Takashi Yasui, Kazutake Takada and Akio Yuchi
Adsorption of hydroquinone (QH2) onto a polycrystalline gold electrode surface in an unbuffered aqueous solution was confirmed by cyclic voltammetry (CV) and time-of-flight secondary ion mass spectrometry. The adsorption appeared to inhibit direct electron transfer between QH2 in the solution and the gold electrode. CV indicated that the surface coverage was ca. 9 × 10−11 mol cm−2. It was also demonstrated that when QH2 was electrochemically oxidized, the adsorbed QH2 likely desorbed from the gold surface.
H675
Yoshiharu Mukouyama, Hirokazu Kawasaki, Daisuke Hara, Yuri Yamada and Shuji Nakanishi
The reduction of H2O2 on Pt electrodes in H2SO4 solution shows various types of electrochemical oscillations, named sequentially from A to H, as has been reported previously. One of them, oscillation H, appears when Na2SO4 or K2SO4 is added to the acidic solution. In the presence of the cation dissociated from the salt, Na+ or K+, the pH at the electrode surface becomes basic during the H2O2 reduction, leading to the appearance of oscillation H. This present work demonstrates that new types of oscillations, named oscillations I and J, are also induced by the pH increase due to the cation. In contrast to oscillation H, oscillations I and J also appear when the H2O2 reduction occurs on Pt electrodes in NaOH solution. They are caused by an N-shaped negative differential resistance (N-NDR) induced by the formation of under-potential deposited H. Oscillation I appears in the potential region of the N-NDR, whereas oscillation J appears at potentials more negative than the N-NDR region, i.e., at potentials where hydrogen evolution reaction occurs. Detailed studies reveal that oscillations I and J are classified into an N-NDR and a coupled N-NDR (CN-NDR) oscillator, respectively.
H685
Kedan Lu, Qinyan Lu, Lijie Zhang, Jianying Gong and Run Liu
Thin CuI layer has been deposited on the electrodeposited Cu2O film through adsorption I− ions in 2 mM KI at room temperature and pH 3 and its effect on the photoelectrochemical properties of Cu2O has been studied. The electrodeposited Cu2O shows (100) preferential orientation and the chemical deposited CuI shows (111) preferential orientation. XPS results show that the Cu+ valence state dominated on the surface of Cu2O/CuI electrode instead of Cu2+ valence state dominated on the surface of Cu2O electrode. With optimum thickness of CuI layer, the photoelectrochemical response for Cu2O/CuI electrode is largely enhanced. The mechanism for the improvement of the photoresponse has been studied and could be due to positive shift of flatband, longer photogenerated electron lifetime, better charge transfer and less charge recombination for the Cu2O/CuI electrode.
H691
The following article is Open access
Meng Zhao and Alfred B. Anderson
The amount of under-potential-deposited (UPD) H(ads), if it forms on Cu(111), is small compared to what forms on Pt(111). According to experimental literature, current density on polycrystalline copper increases slowly in the over-potential-deposited (OPD) potential range beginning at 0 V and rises rapidly at several hundred mV negative potential. Using a comprehensive density functional theory for the electrochemical interface, including Fermi level shifts, in this article we attribute this behavior to calculated weak H adsorption which requires the potential to be reduced to ∼0.0 V(SHE) in order for H(ads) deposition to commence. A literature estimate, based on exchange current densities, of the activation energy for H2 evolution at 0 V is ∼0.32 eV. As the coverage increases with increasingly negative potentials, we calculate the H adsorption energy decreases at a rate 0.27 eV/V for Cu(111), and this will decrease the effective activation energy. We propose that the observed rapid increase in current density at approximately −0.4 V corresponds to ∼0.5 ML coverage by H(ads) and reflects the decreasing activation energy at more negative potentials. We also relate our calculated findings to the literature for electroless copper deposition and to literature for palladium-doped copper as a heterogeneous hydrogenation catalyst.
H696
Changchun Jin, Cuicui Wan and Rulin Dong
The surface modification of Pd nanoparticles supported on reduced graphene oxide (Pd/RGO) with a small amount of Au and the electrocatalytic oxidation of propane-1,2-diol on the Au-modified Pd/RGO (Au/Pd/RGO) are investigated. The modification of Pd/RGO was performed by electrochemically deposing Au on the Pd surfaces. Characterizations by transmission electron microscopy, scanning electron microscopy and X-ray diffraction analyses and electrochemical analysis revealed that Pd nanoparticles were finely distributed on RGO and a small part of the Pd surface was covered by Au. The Au-modified Pd/RGO catalysts show higher activity than Pd/RGO for propane-1,2-diol oxidation in alkaline solution. For example, the peak intensity for Au/Pd/RGO with a Au:Pd atomic percent of 1.67% is about 2 times higher than that for Pd/RGO. On the other hand, the activity enhancement of bulk Pd electrode by the modification with Au is less effective. The results show that the modification of Pd/RGO catalysts with a small amount of Au is very effective for activity improvement, and the as-prepared catalysts also have a great advantage over AuPd alloy or core-shell catalysts in cost.
Errata
X17
Alvaro Soliz and Luis Cáceres
X18
Qiming Chen, Rong Xu, Zitao He, Kejie Zhao and Liang Pan
X19
Taylor R. Garrick, Xinyu Huang, Venkat Srinivasan and John W. Weidner