Batteries and Energy Storage
A349
L. Croguennec, J. Bains, M. Ménétrier, A. Flambard, E. Bekaert, C. Jordy, P. Biensan and C. Delmas
A356
Akira Doi
A362
Andrew van Bommel and J. R. Dahn
A366
Masanori Morishita, Seijiro Ochiai, Tadashi Kakeya, Tetsuya Ozaki, Yoshiteru Kawabe, Masaharu Watada and Tetsuo Sakai
A371
Shunsuke Muto, Yusuke Sasano, Kazuyoshi Tatsumi, Tsuyoshi Sasaki, Kayo Horibuchi, Yoji Takeuchi and Yoshio Ukyo
A378
Tarik Bordjiba and Daniel Bélanger
A385
Lynn Trahey, John T. Vaughey, Harold H. Kung and Michael M. Thackeray
A390
Maureen Tang, Paul Albertus and John Newman
Empirical observations have shown that lithium deposition occurs preferentially at electrode edges and that extending the negative electrode beyond the edge of the positive by approximately
can prevent deposition from occurring. In this work, we use a simplified COMSOL Multiphysics model to explain this behavior and to investigate the conditions under which deposition occurs, paying particular attention to the magnitude of edge effects. Model results show that geometric effects generate overpotential at the edge of the electrode and create conditions which favor plating, despite unused capacity in the center of the electrode. Extending the negative electrode beyond the edge of the positive provides excess capacity where it is needed and prevents deposition from occurring before the cutoff potential is reached. Under the assumptions of this model, an extension of
is sufficient to prevent the onset of lithium deposition until after the cutoff potential is reached.
Fuel Cells and Energy Conversion
B553
Wai Lung Law, Alison M. Platt, Priyantha D.C. Wimalaratne and Sharon L. Blair
Palladium (Pd) anode catalyst shows high electrocatalytic oxidation activity under ambient conditions for direct formic acid fuel cell (DFAFC) operation. However, the highly active Pd is susceptible to significant catalyst poisoning by impurities present in the fuel. In this study, the effect of methyl formate, methanol, and acetic acid impurities on DFAFC performance was investigated. These organic impurities will increase the poisoning rate of the highly active Pd catalyst, resulting in a reduction of fuel cell power output. The impact on performance of various levels of impurities is reported.
B558
Michael J. Martínez, Sirivatch Shimpalee, J. W. Van Zee and A. V. Sakars
Data for hydrophilic and hydrophobic pore-size distributions are presented for two gas-diffusion media (GDM) commonly used in proton exchange membrane fuel cells (PEMFCs). The data were obtained using two measurement methods, intrusion porosimetry and the method of standard porosimetry (MSP). The use of multiple working fluids to access hydrophilic and hydrophobic pores is discussed as well as limitations associated with structural changes of the GDM during the tests. The differences in the data between the two methods are discussed for both the carbon-cloth and carbon-paper GDM and it is shown that these differences have significant implications relative to the distribution of hydrophilic and hydrophobic pores that control liquid-water transport. The analysis presented in this work shows that the MSP can lead to a more consistent interpretation of the GDM structure for materials that are compressible.
B565
Fikile R. Brushett, Wei-Ping Zhou, Ranga S. Jayashree and Paul J.A. Kenis
B572
Yu-ki Taninouchi, Naoyuki Hatada, Tetsuya Uda and Yasuhiro Awakura
B580
I. E. Paulauskas, J. E. Katz, G. E. Jellison Jr., N. S. Lewis, L. A. Boatner and G. M. Brown
The effects of compositionally induced changes on the semiconducting properties, optical response, chemical stability, and overall performance of
photoanodes in photoelectrochemical (PEC) cells have been investigated. Single crystals of n-type Ca- and Ba-doped
with carrier concentrations ranging from
were grown and characterized as photoanodes in basic aqueous electrolyte PEC cells. The PEC properties of the crystals, including the photocurrent, photovoltage, and flatband potential in contact with
NaOH(aq) were relatively independent of whether Ca or Ba was used to produce the semiconducting form of
. All of the Ca- or Ba-doped
single-crystal photoanodes were chemically stable in the electrolyte and, based on the open-circuit potential and the band-edge positions, were capable of unassisted photochemical
and
evolution from
. The minority-carrier diffusion lengths values were small and comparable to the depletion region width. Photoanodic currents were only observed for photoanode illumination with light above the bandgap (i.e.,
). The maximum external quantum yield occurred at 
, and the depletion width plus the minority-carrier diffusion length ranged from
for the various
-based photoanode materials.
B588
Yueping Xiong, Katsuhiko Yamaji, Teruhisa Horita, Harumi Yokokawa, Jun Akikusa, Hiroyuki Eto and Toru Inagaki
B593
Juan Herranz, Michel Lefèvre and Jean-Pol Dodelet
Fe-based electrocatalysts for the reduction of oxygen in polymer electrolyte membrane (PEM) fuel cells have been prepared by adsorbing either
or
ions on two carbon blacks to determine if their maximum activity is limited by (i) the maximum number of micropores available to host catalytic sites in the support or by (ii) the maximum number of ions able to be adsorbed on the carbon. The two carbon supports having the same microporous surface area, one etched in air and the other in
, were derived from the same carbon black (N234). Air-etched N234 is more acidic in nature as it possesses carboxylic functionalities that can adsorb
, while
-etched N234 possesses both pyridinic and carboxylic functionalities that can adsorb either
or
. Catalysts were prepared by heat-treating, in pure
, the materials resulting from
or
adsorption on both etched carbons. It is concluded that, when catalysts are prepared in pure
, the catalytic activity is only governed by the number of micropores, having a size between 0.8 and
, that are available to host the catalytic sites in the porous volume of the carbon support, because Fe ion uptake by adsorption is never the limiting factor.
B602
Leta Y. Woo, Robert S. Glass, Raymond J. Gorte, Christine A. Orme and A. J. Nelson
B609
Toru Hatae, Yoshio Matsuzaki, Satoshi Yamashita and Yohtaro Yamazaki
Cell damage caused by redox cycling in which the anode is electrochemically oxidized was investigated in order to detect the initial damage before cell failure. In order to prevent catastrophic destruction of the cell, partial electrochemical oxidation was used in the redox treatment and controlled at a very low degree of oxidation of the anode. As a result, the cell performance degraded because of the partial redox cycles without a decrease in open-circuit voltage, and no mechanical damage was observed in the electrolyte. However, microcracks at the interfaces between ScSZ particles and Ni particles in the anode layer in active cell area were observed. These results indicated that the microcracks in the anode layer were the initial damage caused by partial redox cycles in which the anode was electrochemically oxidized and caused the degradation of the cell performance.
B614
M. D. Gasda, R. Teki, T.-M. Lu, N. Koratkar, G. A. Eisman and D. Gall
B620
Ju-Sik Kim, Su-Il Pyun and Heon-Cheol Shin
B628
Nobutaka Endo, Kousou Matsuda, Kazuaki Yaguchi, Zhaoxia Hu, Kangcheng Chen, Mitsuru Higa and Kenichi Okamoto
B634
Surinderjit Singh Bhella and Venkataraman Thangadurai
The effect of preparation temperature on electrical conductivity of
,
, and
was investigated in air and humidified
and
. Powder X-ray diffraction (PXRD) showed the formation of double-perovskite-type structure. Among the compounds investigated,
showed the highest proton conductivity of 3.7 and
at
in wet
, respectively, for a 1400 and
sintered sample, while no change in conductivity was observed in air. PXRD showed that
is stable against chemical reaction with
(LSM) and
(SSC) electrodes at 800 and
. Chemical compatibility was further confirmed by energy-dispersive X-ray (EDX) analysis. The ac impedance employing Pt, LSM, and SSC electrodes on
showed that the area specific polarization resistance (ASPR) decreased in wet atmospheres compared to that of air. Unlike the oxide ion system, the ASPR was found to be much higher for the presently investigated proton system, suggesting that proton conductivity at the electrolyte and electrode interfaces or water effusion through microspores appears to control the ASPR. Among the electrodes tested, based on ac impedance studies, the LSM appears to be a better electrode compared to SSC for Ta-doped
electrolyte.
B643
L. Jiang, A. Hsu, D. Chu and R. Chen
B650
A. D. Modestov, M. R. Tarasevich, V. Ya. Filimonov and A. Yu. Leykin
B657
T. Madden, D. Weiss, N. Cipollini, D. Condit, M. Gummalla, S. Burlatsky and V. Atrazhev
In this work, chemical degradation is studied using highly controlled measurements of the fluoride ion release from subscale cells in degrading environments using perfluorosulfonic-acid-based membrane electrode assemblies, primarily with cast, 
thick membranes. Effects of key variables, such as oxygen concentration, relative humidity (RH), temperature, and membrane thickness on the fluoride ion emission rate (FER) are described under open-circuit decay conditions. Some of the observed trends are expected or consistent with previous observations, such as decreasing FER with decreasing temperature and increasing RH. Other trends observed are not expected, such as a logarithmic decrease of FER with oxygen concentration and increasing FER with increasing membrane thickness. Cross-sectional transmission electron microscopy analysis of decayed membranes indicates a surprisingly homogeneous distribution of small Pt particles (
in diameter), presumably from dissolution and migration from the cathode. The experimental results are consistent with radical generation at these Pt particles from crossover hydrogen and oxygen, subsequent radical migration, and polymer attack. The response of the FER to new experimental conditions in this study suggests that the attack can exist at any plane within the membrane, not just the “Xo” plane of maximum Pt precipitation.
B663
Marcel Vogler, Anja Bieberle-Hütter, Ludwig Gauckler, Jürgen Warnatz and Wolfgang G. Bessler
This paper presents a modelling study of the electrochemical hydrogen oxidation reaction at nickel/yttria-stabilized zirconia (Ni/YSZ) patterned anodes. An elementary kinetic reaction-diffusion model accounts for coupled heterogeneous chemistry and transport on the Ni and YSZ surfaces. Charge transfer is modeled as a spillover of adsorbates between the Ni and YSZ surfaces at the three-phase boundary (TPB). No a priori assumptions on rate-determining processes are made. Thermodynamic, kinetic, and transport parameters are compiled from various literature sources serving as a base for quantitative simulations. Seven different spillover reaction pathways of the hydrogen oxidation reaction are compared to experimental patterned anode data obtained previously by Bieberle et al. [ J. Electrochem. Soc. , 148 , A646 (2001)] under a range of operating conditions. Only one reaction pathway, based on two hydrogen spillover reactions, is able to describe consistently the complete experimental data set. A sensitivity analysis for this case allows identification of rate-determining processes. Surface concentrations close to the TPB are predicted to differ from the concentration derived from thermodynamical equilibrium by up to 2 orders of magnitude. The simulation results and the validity of the model are critically discussed. Directions for future theoretical and experimental studies for elucidating the mechanistic details of Ni/YSZ anodes are given.
Corrosion, Passivation, and Anodic Films
C167
X. Yang, X. Peng, C. Xu and F. Wang
C176
X. Hu, Z. Y. Ling, X. H. He and S. S. Chen
The transmission spectra for photonic crystal in anodic alumina have been investigated with the periodic anodization voltage function, including the time, periodicities, and voltage. The shift of the transmission dips can be related to the current density-time curve. The intensity of the diffraction light in anodized alumina is determined by the branched channel, including the length and the pore diameter, and the periodicities. The width of the transmission dip is affected by the distribution of the distance between the two branched channels and the variety of the pore diameter from the initial to the bottom of the film. Photonic crystal of anodized alumina for the optimized function of voltage is obtained with the 4.7% transmission intensity at
of the transmission dip and 89.3% transmission intensity at
.
C180
Nicolas Dupré, Jean-Frédéric Martin, Julie Oliveri, Patrick Soudan, Dominique Guyomard, Atsuo Yamada and Ryoji Kanno
Electrochemical/Chemical Deposition and Etching
D169
J. F.M. Oudenhoven, T. van Dongen, R. A.H. Niessen, M. H.J.M. de Croon and P. H.L. Notten
D175
M. E. Huerta Garrido and M. D. Pritzker
D184
A. G. Muñoz and H. J. Lewerenz
The formation of Ir nanoislands onto n-type Si(111) surfaces by electroreduction from chloride solutions containing i-propanol was investigated by electroanalytical techniques together with ex situ morphological and in-system surface spectroscopic analyses. It was found that the reduction of Ir(III) species takes place via the conduction band under semiconductor accumulation conditions. The early instants of deposition are characterized by an instantaneous type of nucleation involving the formation of Ir adatoms on surface active sites. Further growth of nuclei leads to an arrangement of finely dispersed nanoislands of
size. The electronic properties of the nano n-Si(111)/Ir junctions, investigated by the impedance behavior of the conditioned surface, reveal the formation of an interfacial ultrathin oxide layer accompanying the reduction process, as confirmed by synchrotron-radiation photoelectron spectroscopy experiments.
D188
Chang-Soo Lee, Jungwon Kim, J. Y. Son, W. J. Maeng, Du-Hwan Jo, Wonyong Choi and Hyungjun Kim
Electrochemical Synthesis and Engineering
E81
Ken Watanabe, Daisuke Takauchi, Masayoshi Yuasa, Tetsuya Kida, Kengo Shimanoe, Yasutake Teraoka and Noboru Yamazoe
E86
M. Saito, H. Sasaki, K. Katou, T. Toba and T. Homma
Sn–Cu films were electroplated on Cu seed layers of various thicknesses. The velocity of the diffusion of Cu atoms from a seed layer into the electroplated Sn–Cu film was investigated, focusing on the effect of microstructural properties of the film. It was found that the diffusion velocity of Cu from a Cu seed layer into the electroplated Sn–Cu film increased with a decrease in the thickness of the Cu seed layer. Moreover, the film microstructure was influenced by the thickness of the Cu seed layer. When the crystalline quality of the Cu seed layer was inferior, a large lattice mismatch developed at the interface between the electroplated Sn–Cu film and the Cu seed layer. As a result of this lattice mismatch, many lattice defects and stress may exist at the interface between the electroplated Sn–Cu films and the Cu seed layers. Therefore, the lattice mismatch was considered to be related to the high-diffusion velocity of Cu from the Cu seed layer. Furthermore, the high-diffusion velocity of Cu was found to cause whisker formation.
Physical and Analytical Electrochemistry
F67
D. M.F. Santos and C. A.C. Sequeira
Direct borohydride fuel cells are among the latest fuel cell types under considerable research and development. There is a clear need for further elucidation of the borohydride electrochemical oxidation. From this perspective, potential step experiments were carried out with a Au disk electrode in alkaline sodium borohydride solutions of varying concentrations and temperatures. Analysis of the current transients for the full time scale enabled the delimitation of the domains where diffusion, electron transfer, and mixed control prevail. Chronoamperometric measurements in the diffusion-controlled region led to current responses exhibiting Cottrellian behavior, from which accurate diffusion coefficients,
, were estimated. Arrhenius plots of
allowed determination of the diffusion activation energies and maximum diffusion coefficients. Chronocoulometric measurements generated Anson plots from which the kinetic rate constants and charge transfer activation energies were calculated. Analysis of the current densities in conditions of infinite mass transfer led to Tafel plots from which exchange current densities, transfer coefficients, standard rate constants, and standard activation energies for charge transfer were determined. Purely charge-transfer regimes were not recognized in the studied system under the imposed potentials.
F75
Yao-An Chung, Yu-Cheng Chang, Ming-Yen Lu, Chiu-Yen Wang and Lih-Juann Chen
F80
Kelly L. Sowers and Akiko Fillinger
Dielectric Science and Materials
G29
I. Baginskiy and R. S. Liu
G33
W. J. Maeng, J. Y. Son and Hyungjun Kim
G37
Shou-Yi Chang, Ming-Ku Chen and Dao-Sheng Chen
To inhibit rapid Cu diffusion in interconnect structures, an effective diffusion barrier of high thermal stability is strongly demanded. Thus in this study a nitride nanocomposite film of equimolar five-element high-entropy alloy (AlCrTaTiZr)N was developed and deposited by reactive sputtering. Thermal stability of the (AlCrTaTiZr)N film and its barrier performance to the interdiffusion of Si and Cu were investigated under thermal annealing at
. The (AlCrTaTiZr)N film, constructed of mixed crystalline and amorphous nanocomposite structure, was found to remain thermally stable at an extremely high temperature of
with low electrical resistance. Neither interdiffusion between Si and Cu through the (AlCrTaTiZr)N layer nor formation of any silicides occurred. Severe lattice distortions caused by the addition of multiprincipal elements and the nanocomposite structure of nanocrystallites surrounded by an amorphous matrix without the existence of grain boundaries were expected as the dominant factors for the high thermal stability and superior diffusion resistance of the (AlCrTaTiZr)N film as an effective barrier material.
G43
Kwun-Bum Chung, W. J. Lee, C. Y. Kim, Mann-Ho Cho and Dae Won Moon
G48
Jeong Hwan Kim, Tae Joo Park, Moonju Cho, Jae Hyuck Jang, Minha Seo, Kwang Duk Na, Cheol Seong Hwang and Jeong Yeon Won
G53
S. Abermann, C. Henkel, O. Bethge, C. J. Straif, H. Hutter and E. Bertagnolli
Semiconductor Devices, Materials, and Processing
H299
Daiji Noda, Hiroshi Tsujii, Naoki Takahashi and Tadashi Hattori
The X-ray radiographic imaging technique is very important in medical, biological, inspection, material science, and other fields. However, it is not enough to obtain a clear X-ray image of samples with low absorbance materials, such as biological soft tissues. Then, we have used an X-ray phase-imaging method of an X-ray Talbot interferometer. In this method, X-ray gratings were required to have a narrow pitch and high aspect ratio structure. Therefore, we have developed and fabricated high-aspect-ratio X-ray gratings with a pitch of
, a height of
, and a large effective area of
using X-ray lithography and narrow electroforming techniques. In this paper, we discuss the fabrication process of X-ray gratings with a narrow pitch and high-aspect-ratio structure, and results of X-ray phase tomography using an X-ray Talbot interferometer with these X-ray gratings.
H303
M. P. Breninford, C. A. Colinge, S. L. Holl, K. D. Hobart and F. J. Kub
A comparison of Si surface treatments for hydrophobic wafer bonding was conducted. Surface energies were found for wafers with preactivation treatments consisting of UV and heat exposure. Bonded hydrogen-terminated silicon (100) which was activated simultaneously with short-wavelength
UV/heat and bonded in an inert
environment showed the highest bond strengths. The results are consistent with other studies of the dynamics of hydrogen on silicon (100).
H307
Xiaobo Ma, Chao Chen, Weili Liu, Xuyan Liu, Xiaofeng Du, Zhitang Song and Chenglu Lin
H311
A. Lintanf Salaün, A. Mantoux, E. Blanquet and E. Djurado
H316
Chung-Chieh Yang, Chia-Feng Lin, Hsun-Chih Liu, Chun-Min Lin, Ren-Hao Jiang, Kuei-Ting Chen and Jui-Fen Chien
Self-assembled hexagonal inverted pyramid (HIP) structures were formed at the mesa-edge region in the InGaN-based light emitting diodes (LEDs). The HIP structures consisted of the top p-type GaN:Mg layers and the bottom InGaN active layers, and they were fabricated through a bandgap-selective photoelectrochemical (PEC) wet-etching process in a
potassium hydroxide solution. In the HIP-LED structures, the light output power was 1.6 times higher and the divergent angle was reduced to 146° compared to a standard LED without PEC treatment. The light emission extracted from the InGaN active layer was scattered in a normal direction through the hexagonal inverted pyramid structures located at the
wide mesa-edge regions without depositing any transparent metal contact layer.
H320
Tsutomu Shinagawa, Kuniaki Murase, Satomi Otomo, Jun-ichi Katayama and Masanobu Izaki
In the chemical ZnO deposition on Pd-catalyzed glass from aqueous dimethylamineborane (DMAB) solutions, effects of counteranions (
,
,
, and
) and dissolved oxygen (DO) on the hydrolysis behavior of
and the growth regime of ZnO were studied using sodium and zinc salt solutions bubbled with
, air, or Ar gas. The interaction of the counteranions with
and Pd as well as
was suggested as an important factor for the chemical ZnO deposition, and it was found that only
can raise the pH of a DMAB solution without DO, affording the continuous ZnO growth. Dissolved oxygen accelerated the ZnO nucleation process on the Pd and had less influence comparable to
on the subsequent growth on the ZnO surface. The ZnO films deposited from
–DMAB solutions bubbled with
, air, or Ar gas were characterized with an X-ray diffractometer, field emission scanning electron microscope, UV-visible spectrophotometer, and Hall coefficient analyzer. The Ar-bubbled solution gave superior ZnO films in terms of crystallinity, growth orientation, surface morphology, and electrical conductivity due to the relatively moderate crystal nucleation compared to in the presence of DO.
H327
Sarah Messina, M. T.S. Nair and P. K. Nair
H333
Sang-Woo Kang, Young-Jae Park, Yong-Sung Kim, Yong-Hyeon Shin and Ju-Young Yun
The chemical species in gas phase and on the surface of aluminum borohydride trimethylamine (ABHTMA) for aluminum chemical vapor deposition as a function of the hot-wall temperature and the chamber pressure were studied using two kinds of Fourier transform IR spectroscopes installed at the end of the chamber. The absorbance of Al–H, B–H, C–H, and C–N stretching features of ligands in ABHTMA in the gas phase and on the surface was sensitive to the variation of analysis conditions. The area ratio of integrated absorbance of Al–H and B–H stretching features located at the different position could estimate the dissociation rate of the ABHTMA, which was abruptly changed in the range of
. With these results, the temperature dependence of the film composition and quality could be explained. Additionally, the stabilities of the chemical species were investigated using density functional theory calculations. The ABHTMA was found to be the most stable molecule when trimethylamine was rich and borane and alane were close in their concentrations. Borane-trimethylamine was also found to be produced in alane-poor conditions as a by-product.
H340
F. Staudegger, M. W. Hofbaur and H.-J. Kruwinus
We investigate wet chemical etching of bare silicon wafers using a configuration where the wafer rotates and the etchant is supplied to the wafer by a nozzle positioned above the wafer center. The purpose of this study is to identify the change of the etch-rate profile on the wafer in relation to the parameters of speed of rotation, etchant flow rate, and etchant temperature. All of them influence the flow velocity of the etchant on the wafer. As a consequence, we propose to use a simplified model that captures the etchant flow velocity on the rotating wafer in sufficient detail to imply the etch-rate profiles for the wet-chemical-etching process of bare silicon wafers. We validate our approach against measured etch-rate profiles for a wide variety of parameter settings.
H346
Samuel Crawford, Elijah Thimsen and Pratim Biswas
Despite extensive research in photocatalytic water splitting, electrolyte usage varies greatly across different photocells. Photocatalytic water splitting continues to be performed in a wide range of electrolytes, from very acidic to very basic, with incomplete understanding of how the electrolyte composition affects performance. This study provides guidelines for electrolyte selection in water splitting applications. To determine properties that comprise an ideal electrolyte for photocatalytic electrolysis, the effects of several parameters were studied: pH, dissolved oxygen, conductivity, and composition. The photoactive anode was a nanostructured thin
film synthesized by a flame aerosol process. The photocatalytic conversion efficiency increased with both pH and conductivity, but changes in dissolved oxygen levels had no discernible effect. The electrolyte composition was adjusted using selected salts and bases. Although the effect of the cation was negligible, anions were found to reduce efficiencies if their oxidation potential makes them thermodynamically favored over water molecules for oxidation. The results of these studies were applied in an analysis of the prospects for splitting seawater to produce hydrogen.
H352
Jaesang Lee, Keunwoo Lee, Taeyong Park, Dongock Kim and Hyeongtag Jeon
H356
Chin-Lung Cheng, Chien-Wei Liu, Jin-Tsong Jeng, Bau-Tong Dai and Yen-His Lee
H361
Shao-Ming Koh, Xincai Wang, Karuppanan Sekar, Wade Krull, Ganesh S. Samudra and Yee-Chia Yeo
H367
Ching-Sung Lee, Wei-Chou Hsu, Chiu-Sheng Ho and An-Yung Kao
H372
Jeff Bailey, Thomas Qiu, Hood Chatham, Helmuth Treichel and Khalid Mohamed
Deal–Grove oxidation rate constants for the controlled combustion-based radical oxidation of silicon wafers in a batch reactor were determined, thus providing insight into the rate-limiting factors. Re-examination of the oxidation rates of wafers with different crystal orientations provides an estimate of the enhancement of the linear rate constant in radical oxidations as compared to standard wet and dry oxidation processes.
H378
Emre Alptekin, Mehmet C. Ozturk, Veena Misra, Yonah Cho, Yihwan Kim and Saurabh Chopra
H384
Toshihiro Kugimiya, Hiroshi Goto, Nobuyuki Kawakami, Junichi Nakai, Yoichiro Yoneda and Eisuke Kusumoto
H390
Bum Soo Kim and Stephen P. Beaudoin
Copper planarization is of great interest in the microelectronics industry. In this work we monitored surface film formation on a copper wire in situ by tracking the time evolution of the system impedance in aqueous phosphoric acid, a condition relevant to electrochemical mechanical planarization (eCMP). First, potentiodynamic scans (PD scans) were performed in order to characterize the active and passive behavior of copper in the solutions. Then copper was biased at various potentials obtained from the PD scans, and the impedance at high frequencies (100 and
) was monitored to detect the formation of a surface film over the copper. A newly designed guillotined electrode was employed to create fresh copper surfaces in the solution in situ. The transient impedance response immediately following copper exposure to solution clearly shows that a resistive film, presumably either a porous salt or viscous liquid, does form over the copper surface in the passive region. These films will have implications in potential eCMP and electropolishing protocols.
H396
Haiping Yang, Xiaolan Song, Guanzhou Qiu, Motang Tang and Shenghai Yang
The effects of process parameters on electrochemical characteristics of silicon wafers during chemical mechanical polishing (CMP) as well as under static conditions were studied by dc polarization and open-circuit potential (OCP) techniques. All the process parameters strongly affected the electrochemical behaviors and polishing rates. The corrosion current density first increased rapidly when raising polishing pressure, rotation speed, and silica solid content and then began to slow down. The polishing rate declined gradually with the increase of polishing time due to the pad surface plastic deformation during CMP. Also, the CMP process of silicon wafers could be considered as a sequential formation and removal of a film, which was confirmed by testing the change of OCP. A low surface roughness could be obtained after CMP.
Sensors and Displays: Principles, Materials, and Processing
J81
I. Braems, S. Franger and F. Berthier
We present a test to discriminate equivalent electrical models via electrochemical impedance spectroscopy (EIS) data collected on a frequency response analyzer (FRA). Derived in the set-membership framework, this test is an interesting alternative to classical estimators, as it does not rely on statistical thresholding and bypasses many numerical limitations (initialization, convergence) of nonlinear least-squares methods. Models are systematically discarded when their associated impedance is proved not to satisfy both the experimental data and the uncertainty range of the FRA. In this paper, we detail the methodology adapted to FRA measurements and apply the test on known electrical circuits to evaluate the required uncertainty ranges of different commercial impedance meters.
J92
Chih-Hao Tsai and Fu-Ming Pan
J97
Masahiro Takesada, Morio Osada and Tetsuhiko Isobe
The photoluminescence (PL) intensity of
(MGM) nanophosphors synthesized by glycothermal reaction are
times higher than that of
(ZGM) nanophosphors. We discuss this reason from the following points of view: (i) Mn contents, (ii) particle size, (iii) crystallinity, (iv) spontaneous pressure, (v) emission mechanism, and (vi)
state. Judging from the results of the X-ray fluorescence analysis, transmission electron microscopy, X-ray diffractometry, PL spectroscopy, and electron paramagnetic resonance spectroscopy, the more homogeneous distribution of
ions in the matrix of MGM is the predominant factor for determining the PL intensity.
ions are more homogeneously incorporated into ZGM after post–heat-treatment at
for
in Ar in comparison to MGM. This is explained by the geometrical reason: the order of ionic radius for tetrahedral coordination is 


. These results indicate that the glycothermal reaction promotes the incorporation of
in MGM nanosphosphor, resulting in the higher PL intensity of MGM than that of ZGM. This is attributed to the formation of the low-crystallized MGM glycoxide precursor with the higher homogeneous mixture of different metallic ions.
J102
Ryotaro Wama, Vladimir V. Plashnitsa, Perumal Elumalai, Toshikazu Kawaguchi, Yuki Fujio, Masahiro Utiyama and Norio Miura
In an effort to improve propene
selectivity and long-term stability of the mixed-potential-type yttria-stabilized zirconia (YSZ)-based tubular sensor attached with
sensing electrode (SE), each of the nanosized noble metals (Pt, Ru, Pd, Rh, or Ir) and YSZ powder was added to
SE. It was found that the addition of nanosized Pt
gave considerable improvement in
selectivity, and the addition of YSZ powder
exhibited great improvement in long-term stability of the sensor. Thus, the sensor attached with composite SE consisting of
,
Pt, and
YSZ was fabricated and its sensing characteristics to
were examined. As a result, the present sensor exhibited high selectivity and excellent long-term stability to
at
under the wet condition for the examined period of about
. Based on the results obtained from the measurement of catalytic activity for CO oxidation to
, the observation of morphology, and the analysis of composition of SEs, it was speculated that the added Pt nanoparticles could promote the oxidation of CO and
and then improve the
selectivity, while the added YSZ powder could stabilize the morphology of the SE∕YSZ interface and give better long-term stability.
J108
Tung-Ming Pan, Chih-Hung Cheng and Cheng-Da Lee
J112
H. L. Li, Z. L. Wang, S. J. Xu and J. H. Hao
Spherical
phosphors were prepared by the polyol method and postannealed at
. A variety of properties were characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, Fourier transform IR spectra, low-voltage cathodoluminescence, photoluminescence spectra, and lifetime. The as-prepared phosphors were well-crystallized under relatively low synthesis temperature
and composed of spherical particles with an average size of
. After postannealing treatment, crystallinity of the phosphors is significantly improved and average particle size is increased to around
. Under low-voltage
excitation of electron beam, bright green cathodoluminescence was observed, which is attributed to the characteristic emissions from
(
and
transitions). The luminance was significantly improved from
after postannealing, which is mostly attributed to the improvement of crystallinity.
J117
Haiyan Jiao and Yuhua Wang
Rare-earth-activated, white-emitting phosphors
,
were prepared under a weak reducing atmosphere by conventional solid-state reaction and their luminescence properties under
excitation were investigated in detail.
shows excitation at short-UV wavelength light
.
,
showed optimal excitation at long-UV light excitation
. By incorporation of
, an efficient energy transfer from
to
was found and generated white light under long-UV excitation. The emission spectra consisted of a blue band
and a green band
, the relative intensities of which changed with the rare earth dopant concentration
and
. As a result, the optimal concentration for the best luminescence intensity was obtained in 
, 0.030
, and the closest to daylight white emission was found with a composition of 
, 0.020
, which has chromaticity coordinates
,
. This is considered to be a potential white-emitting phosphor for white light-emitting diodes.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K65
Xiaomeng Wu, Yunhan Ling, Li Liu and Zhaohui Huang
K72
Jyh Ming Wu
K77
Enrique A. Dalchiele, Francisco Martín, Dietmar Leinen, Ricardo E. Marotti and José Ramón Ramos-Barrado
K82
Y. H. Tong, J. Cheng, J. Q. Deng and G. G. Siu
Multilayer ZnO films fabricated by the combination of sol-gel and aqueous solution deposition routes exhibit many flowerlike clusters with the diameter of
on their top layer. Each flowerlike cluster is an assembly of nanoparticles
in diameter. The investigation of electrochemical properties, phase, and composition of the ZnO film before and after cyclic voltammetric measurement revealed that the reaction mechanism of lithium with ZnO in our growth method differs from those from the literature. The proposed reversible electrochemical reactions would potentially cause the improvement of capacity retention and the enhancement of cycling performance, which might break the reported negative conclusions such as poor cycling on lithium storage in ZnO.
K86
Byung Gil Jung, Seok-Hong Min, Chang-Woo Kwon, Sang-Hyun Park, Ki-Bum Kim and Tae-Sik Yoon
The effect of solvents of colloidal solution and substrate withdrawing speed during dip-coating on the nanoparticle-layer formation of sterically stabilized iron oxide
nanoparticles on Si substrates is investigated. From the solutions with
particle concentrations dispersed in hexane, octane, decane, and tetradecane, the multilayer is formed from hexane while the uniform monolayer is formed from octane, decane, and tetradecane. Because the particle layer is formed by direct adsorption and convective flux of particles from solution to substrate, the multilayer formation from hexane is due to the highest interaction energy between particle and substrate and the highest convective flux to the meniscus region of the substrate caused by the highest evaporation rate. Lowering the substrate withdrawing speed increases the particle coverage from
to
at
as locally forming the multilayer regions, which is explained by increased convective flux at reduced speed. These results verify that the colloidal particle delivery to the substrate is determined by factors such as particle–substrate interactions, substrate withdrawing speed, and the evaporation rate of solvent.
K91
Guo Gao and Lan Xiang
Interdisciplinary Topics
P81
Xiaofeng Liu, Yanbo Qiao, Guoping Dong, Song Ye, Bin Zhu, Yixi Zhuang and Jianrong Qiu
A BCNO-based long-persistent phosphor prepared by a low-temperature liquid-phase route is investigated. It shows a phosphorescence peak centered at
and its afterglow decay curve fits
. Electron paramagnetic resonance confirms the presence of a paramagnetic center, the signal of which exhibits a synchronized decay with the afterglow intensity. We assume that the phosphorescence arises from electrons that are thermally released from nitrogen vacancies and then fall into the carbon-related defects, giving the greenish emission. The BCNO material is a competitive long-persistent phosphor because it is derived from cheap raw materials.