Batteries and Energy Storage
A253
Jose A. Vega, Junfeng Zhou and Paul A. Kohl
A260
Venkat R. Subramanian, Vijayasekaran Boovaragavan, Venkatasailanathan Ramadesigan and Mounika Arabandi
This paper presents an effective first step in the mathematical reformulation of physics-based lithium-ion battery models to improve computational efficiency. While the additional steps listed elsewhere [ Electrochem. Solid-State Lett. , 10 , A225 (2007) ] can be carried out to expedite the computation, the method described here is an effective first step toward efficient reformulation of lithium-ion battery models to expedite computation. The battery model used for the simulation is derived from the first principles as an isothermal pseudo-two-dimensional model with volume-averaged equations for the solid phase and with incorporation of concentrated solution theory, porous electrode theory, and with due consideration to the variations in electronic/ionic conductivities and diffusivities. The nature of the model and the structure of the governing equations are exploited to facilitate model reformulation, yielding efficient and accurate numerical computations.
A272
Katsuhiko Naoi, Etsuro Iwama, Nobuhiro Ogihara, Yasuhiro Nakamura, Haruki Segawa and Yuji Ino
A277
Min Gyu Kim and Jaephil Cho
A283
Jing Li, Aaron Smith, R. J. Sanderson, T. D. Hatchard, R. A. Dunlap and J. R. Dahn
A289
Tsuyoshi Sasaki, Takamasa Nonaka, Hideaki Oka, Chikaaki Okuda, Yuichi Itou, Yasuhito Kondo, Yoji Takeuchi, Yoshio Ukyo, Kazuyoshi Tatsumi and Shunsuke Muto
The mechanism for capacity fade of lithium-ion batteries with
as a positive electrode material associated with cycling at elevated temperatures was investigated by the combination of electrochemical and spectroscopic methods. The total capacity fade of the battery after charge/discharge cycle test at
was found to be almost explained by the capacity fade of the positive electrode, which indicates that the degradation of the positive electrode is mainly responsible for capacity fade of the battery at this temperature. Quantitative analyses revealed a strong positive correlation between the capacity fade of the positive electrode and the amount of inactive Ni ions in the active material after the cycling test. It is concluded that the capacity fade is mainly caused by the formation of inactive Ni(II) and Ni(III), presumably associated with oxygen loss in the active materials, which act as obstacles to Li intercalation/deintercalation.
A294
Ming-Qi Li, Mei-Zhen Qu, Xiao-Ying He and Zuo-Long Yu
A299
Shin-nosuke Ichikawa, Mitsuhiro Hibino and Takeshi Yao
A305
Johan Scheers, Michal Kalita, Patrik Johansson, Grażyna Z. Zukowska, Wladyslaw Wieczorek and Per Jacobsson
A309
L. M. Moshurchak, W. M. Lamanna, Mike Bulinski, R. L. Wang, Rita R. Garsuch, Junwei Jiang, D. Magnuson, Matthew Triemert and J. R. Dahn
Redox shuttle additives can be used in lithium-ion cells to protect against overcharging and for cell balancing in multicell packs. Most previously reported redox shuttles have been either unstable as shuttles, resulting in a short duration of overcharge protection, or have redox potentials that make them suitable only for cells containing lower potential positive electrode materials, such as
. A new molecule, 1,4-di-
-butyl-2,5-bis(2,2,2-trifluoroethoxy)benzene, is shown here to be a stable redox shuttle with a redox potential of
and provides overcharge protection in full Li-ion cells, implying adequate reductive stability. Experiments using
and
cells show that this molecule can work with high-energy-density positive electrodes as well as in full cells containing
positive electrodes and Li, mesocarbon microbead, or
negative electrodes.
A313
Yahya A. Ismail, Jonho Chang, Su Ryon Shin, Rajaram S. Mane, Sung-Hwan Han and Seon Jeong Kim
Flexible, controllable, and stable electrochemical supercapacitors serving as actuators at low operating voltage combining the advantages of the high power of the dielectric capacitors and the high specific energy of rechargeable batteries are important in artificial muscle technology, hybrid electric vehicles, and in short-term power sources for mobile electronic devices [ Baughman , Science , 300 , 268 (2003) ; Winter and Brodd , Chem. Rev. (Washington, D.C.) , 104 , 4245 (2004) ; Ebron , et al. , Science , 311 , 1580 (2006) ]. High capacitance, a surprising 99% inner charge contribution and actuation in the hydrogel-assisted actuatable electrochemical supercapacitor (HAES) microfiber fabricated through wet spinning of a chitosan solution, followed by the in situ chemical polymerization of aniline was made possible through the perfect utilization of the large surface area provided by the nanostructured polyaniline grown inside as well as on the surface of the fiber. The HAES electrodes with an actuation strain of 0.33% showed
specific capacitance in
methane sulfonic acid, and more than
durability. The change in impedance as well as capacitance was achieved by the controlled strain as a function of applied stress, which can establish a direct relationship between the actuation strain and specific capacitance of electrochemical supercapacitors.
A318
Ang Xiao, Li Yang, Brett L. Lucht, Sun-Ho Kang and Daniel P. Abraham
A328
S. Sivaprakash, S. B. Majumder and R. S. Katiyar
A334
K. Tõnurist, A. Jänes, T. Thomberg, H. Kurig and E. Lust
The specific surface area, pore size distribution function, micropore and mesopore volume, and area values have been obtained by gas adsorption/absorption method for various separator materials prepared from polypropylene, cellulose, and poly(vinylidene fluoride). Electrical double-layer capacitors (EDLCs) based on the two identical ideally polarizable nanoporous carbide-derived carbon electrodes and different mesoporous separator materials in 
acetonitrile solution have been tested by cyclic voltammetry and electrochemical impedance methods. The limits of ideal polarizability, low-frequency limiting capacitance and series resistance, time constant, complex power components, and electrolyte conductivity in the separator matrix have been obtained and discussed. The model of Srinivasan and Weidner [ J. Electrochem. Soc. , 146 , 1650 (1999)] has been modified by introducing into it the very high-frequency constant phase and charge-transfer resistance elements. The applicability limits of the modified model have been tested. Noticeable influence of separator chemical composition, thickness, specific surface area, and pore size distribution on the characteristics of the EDLC single cells have been found.
A343
Fu Zhou, Xuemei Zhao and J. R. Dahn
Fuel Cells and Energy Conversion
B425
Reidar Haugsrud and Trond Risberg
B429
Md. Rezwan Miah and Takeo Ohsaka
B436
Jinli Qiao, Bing Li and Jianxin Ma
Carbon-supported binary IrM (where
, Mn, Fe, Co, and Ni as the second active component) alloys as a substitute for platinum were viewed as the anode catalysts in polymer electrolyte membrane fuel cells. The resulting
and
of 50:50 ratio, heat-treated at
in argon atmosphere, exhibited promising catalytic performance in terms of the hydrogen oxidation reaction and results in mass activity and specific activity at almost the same level and even a little higher as compared with 20%
at
. These carbon-supported catalysts showed particle sizes ranging from
. Results of electrochemical characterizations, performed using a rotating disk electrode by cyclic voltammetry, linear sweep voltammetry, and chronoamperometry with emphasis on the activity of the catalyst, are presented in 
.
B441
Majid Mosleh, Martin Søgaard and Peter Vang Hendriksen
B458
Jason D. Nicholas and Scott A. Barnett
The polarization resistance of idealized, branched, composite cathodes was modeled using a two-dimensional finite element calculation. The model structures consisted of micrometer-scale columns and nanoscale branches of ionically conducting materials that were coated with a mixed-conducting material. The structures approximate an ionic-conductor matrix infiltrated first with the same ionic-conductor material and then with a mixed conductor. Increasing the length of the ionically conducting nanobranches, and hence, the surface area of the infiltrated mixed conductor, resulted in a factor of
polarization resistance decrease compared to mixed-conductor-coated columns without ionically conducting nanobranches. For many solid oxide fuel cell relevant temperatures
, cathode geometries, and materials, the cathode resistance was limited by surface oxygen exchange and hence, was inversely proportional to the mixed-conductor surface area. However, for cathode columns or branches with large enough aspect ratios, ionic-conduction losses also limited the polarization resistance. The characteristic length of nanostructured cathodes was found to depend on the cathode surface area ratio in addition to the traditional bulk diffusion constant to surface exchange constant ratio
. Lastly, the effects of materials properties, particularly ionic conductivity and surface resistance, were investigated and discussed for common cathode materials.
B465
A. A. Shah, T. R. Ralph and F. C. Walsh
A polymer electrolyte membrane (PEM) fuel cell model that incorporates chemical degradation in perfluorinated sulfonic acid membranes is developed. The model is based on conservation principles and includes a detailed description of the transport phenomena. A degradation submodel describes the formation of hydrogen peroxide via distinct mechanisms in the cathode and anode, together with the subsequent formation of radicals via Fenton reactions involving metal-ion impurities. The radicals participate in the decomposition of reactive end groups to form carboxylic acid, hydrogen fluoride, and
. Degradation proceeds through unzipping of the polymer backbone and cleavage of the side chains. Simulations are presented, and the numerical code is shown to be extremely time-efficient. Known trends with respect to operating conditions are qualitatively captured, and the exhibited behavior is shown to be robust to changes in the rate constants. The feasibility of a chemical degradation mechanism based on peroxide and radical formation is discussed.
B485
Y. Gu, J. St-Pierre, A. Joly, R. Goeke, A. Datye and P. Atanassov
A model Pt catalyst nanoarray on planar glassy carbon (GC) was synthesized using a diblock copolymer synthesis route and subjected to a potential cycle aging procedure. Preliminary experimental data show initial and degradation behavior similar to that of proton exchange membrane fuel cell gas diffusion electrodes. Commonalities include similar cyclic voltammetry and CO stripping voltammetry features, Pt active surface area temporal changes, and Pt particle size effect on CO oxidation peak potential. Furthermore, atomic force microscopy provides evidence for both Pt dissolution and Pt nanoparticle migration/coalescence as aging mechanisms. Experimental data obtained with Pt model catalysts also revealed that Pt dissolution may be the rate-determining step under certain operating conditions. Thus, the beneficial use of Pt/GC model electrocatalysts as surrogates for commercial gas diffusion electrodes is validated.
B493
Ruizhi Yang, Tara R. Dahn and J. R. Dahn
B499
Toby Astill, Zhong Xie, Zhiqing Shi, Titichai Navessin and Steven Holdcroft
B509
Koichiro Asazawa, Tomokazu Sakamoto, Susumu Yamaguchi, Koji Yamada, Hirotoshi Fujikawa, Hirohisa Tanaka and Keisuke Oguro
B513
Yunxiang Lu, Cortney Kreller and Stuart B. Adler
Porous
(LSC) electrodes having Sr composition
(LSC-64) and
(LSC-82) were fabricated on Sm-doped ceria electrolytes, and studied using electrochemical impedance spectroscopy between
and
. The faradaic portion of the impedance was found to exhibit Gerischer or Gerischer-like characteristics, indicating colimitation by kinetics and transport. The characteristic resistance and frequency response was analyzed using a transport and reaction model that considers parallel bulk and surface diffusion of oxygen, as well as three-dimensional transport effects near the electrode electrolyte interface. In the case of LSC-64, measured characteristics appear to be largely consistent with a bulk transport path, based on independent measurements of the thermodynamic, kinetic, and transport properties of LSC-64. In the case of LSC-82, which has a much lower bulk vacancy concentration under the same conditions, results were inconsistent with an entirely bulk transport path. Results for LSC-82 could be rationalized assuming a parallel surface transport path, where surface mobility is governed by some kind of interstitial or adatom diffusion mechanism.
B526
Kevin V. Galloway and Nigel M. Sammes
B532
Hicham Ben youcef, Lorenz Gubler, Tetsuya Yamaki, Shin-ichi Sawada, Selmiye Alkan Gürsel, Alexander Wokaun and Günther G. Scherer
B540
M. D. Gross, K. M. Carver, M. A. Deighan, A. Schenkel, B. M. Smith and A. Z. Yee
B546
M. Williams, K. Yamaji, T. Horita, N. Sakai and H. Yokokawa
The exergetic and thermal efficiency of hybrid systems using various solid oxide fuel cell (SOFC) intermediate-temperature fuel cell electrolytes at various temperatures and electrolyte thicknesses was simulated and evaluated. Electrolytes reported on here include lanthanum strontium gallate magnesite, yttria-stabilized zirconium, and gadolinium-doped ceria oxide (GDC). The Wagner mass transfer model (MTM), which includes solid-state oxygen-ion, hole, and electron conduction, was incorporated into a thermodynamic model for a simple hybrid system. The MTM-projected performance trends for the various electrolytes agreed well with trends previously observed experimentally by the authors for electrolytes alone. The projected exergetic performance with the typical thermodynamic model without the incorporation of the MTM generally gave higher performance over a broader temperature range than expected through experimental trends previously observed. Thus, the projected performance of these very important hybrid systems can be greatly impacted by electrolyte choice and electronic conductivity. GDC was predicted to have a good exergetic efficiency, but only over a very narrow temperature region. A thermodynamically consistent picture of SOFC exergetic performance from the defect chemistry and solid-state electrochemistry to the phenomenological fuel cell and macroscopic thermodynamic performance was established.
Corrosion, Passivation, and Anodic Films
C123
Zhixiang Zeng, Yuanlie Yu and Junyan Zhang
C127
S. Sathiyanarayanan, R. Jeyaram, S. Muthukrishnan and G. Venkatachari
Epoxy–coal tar coatings are widely used to protect steel structures exposed to marine atmosphere due to their good barrier property. However, the presence of micropores and microcracks formed during the coating formation leads to failure of the coating due to permeation of corrosive ions. In recent years, it has been established that the coatings containing polyaniline (PANI) is able to protect pinholes and defects due to its passivating ability. Hence, a study has been made on the effect of polyaniline content (1 and 3%) in epoxy–coal tar coating on the corrosion protection of steel in 3% NaCl solution by electrochemical impedance spectroscopy (EIS) studies. Both phosphate- and chloride-doped polyanilines were prepared by a chemical oxidative polymerization method. From EIS studies, it has been found that the resistance value of the coatings containing 1 and 3% phosphate-doped polyaniline and 3% chloride-doped polyaniline pigmented coatings are
even after
exposure to NaCl solution, which are two orders high in comparison to that of conventional coal tar epoxy coatings. Besides, the conducting state of polyaniline has been found to be decreased after exposure to NaCl solution due to redox property of PANI. X-ray photoelectron spectroscopy studies have shown that polyaniline forms a complex layer with iron beneath the coating along with iron oxide.
C135
K. D. Ralston, T. L. Young and R. G. Buchheit
Experiments were conducted to determine how inhibiting forms of vanadate interact with complex Al alloy microconstituent intermetallics to impart corrosion protection. Cathodic polarization experiments on Al 2024-T3 indicate a strong correlation between inhibition and the presence of tetrahedrally coordinated vanadate. Anodic and cathodic polarization curves were measured on bulk synthesized
,
,
, and
in alkaline
NaCl solutions with and without 
. Vanadate additions generally decreased
, increased
, and decreased the cathodic kinetics of all tested materials. Because of decreased cathodic kinetics, open-circuit potentials (OCPs) were shifted in the active direction in aerated solutions when vanadate was present. This shift pins the OCP just below the observed pitting potential for
in vanadate solution, effectively preventing breakdown and subsequent support of rapid oxygen reduction by Cu-enriched clusters.
,
,
,
,
, and
at
data from polarization experiments were summarized in cumulative distribution plots, and averages are presented in tabulated format. Scanning electron microscopy images of Al 2024-T3 used for
of OCP measurement show that vanadate greatly decreased circumferential trenching around intermetallic particles in both aerated and deaerated solutions. Potentiostatic hold experiments were used to show suppression of
dissolution in vanadate solutions.
C147
M. Curioni, P. Skeldon, E. Koroleva, G. E. Thompson and J. Ferguson
Tartaric acid is added to sulfuric acid anodizing baths to generate porous anodic film that provides corrosion resistance to practical aerospace alloys and reduces the environmental impact of the traditional chromic acid anodizing process. Here, a fundamental study on the effects of the addition of tartaric acid to the sulfuric acid anodizing electrolyte has been undertaken. During anodizing, it was evident that tartaric acid does not significantly affect the mechanism of porous film growth, but it reduces the growth rate of the porous anodic film. After anodizing, in acidic environments, it may reduce the dissolution rate of a previously formed oxide. Furthermore, it was found that in a nearly neutral, chloride-rich environment, tartaric acid limits the anodic reaction of aluminum dissolution at concentrations in the hundreds of ppm range. The previous suggests that the good anticorrosion performance of alloys anodized in the presence of tartaric acid is due to residues of tartaric acid in the pore solution.
C154
Scott P. Harrington and Thomas M. Devine
The films forming on pure chromium and Alloy C22 in aqueous borate buffer were investigated with potential polarization scans, electrochemical impedance spectroscopy, and Mott–Schottky analysis. The capacitances of both films were frequency dependent, and a constant phase element (CPE) best described the frequency dispersion. Cathodic polarization scans were used to assess the accuracy of flatband potential values calculated from Mott–Schottky tests using different models to extract an effective capacitance from a CPE. It was found that using effective capacitances calculated with an expression developed by Brug et al. [ J. Electroanal. Chem. , 176 , 275 (1984)] led to flatband potentials that closely agreed with cathodic polarization scans. Both films were found to be n-type, and flatband potentials of
and
vs standard hydrogen electrode were found for Cr and Alloy C22, respectively.
C160
G. Liu and H. G. Wheat
A fluorescent indicator (FI) can be used to monitor the underlying corrosion on metal substrates based on sensing pH changes caused by corrosion reactions. One coumarin derivative was chosen as FI and added to a coated-aluminum system. The initial state of the coating system is fluorescent under UV light and it changes to nonfluorescent at the site of corrosion. The effects of the fluorescent indicator on the fluorescent intensity and protectiveness of the coating system are discussed. Electrochemical impedance spectroscopy (EIS) was used to estimate the protectiveness of the coating and interface corrosion reactions between the metal and coating. This was correlated with the fluorescent intensity change of the coating. Based on the impedance measured by EIS, the coating failed shortly after immersing into the 3.5% sodium chloride solution. After
, pH-induced fluorescent quenching points began to appear. Scanning electron microscopy and energy-dispersive spectroscopy of selected specimens indicated that the quenching point was the corrosion site. Several coating thicknesses were examined, and based on these tests the optimal coating thickness was determined to be about
.
Electrochemical/Chemical Deposition and Etching
D113
Abdul Rashid, Lars Landström and Klaus Piglmayer
In the present paper, a complex chemical process involving laser-materials interaction within a strong absorbing gas phase is investigated and characterized. The process utilizes excimer laser pulses to dissociate methylene iodide
in the gas phase and to locally heat the surface of a silicon substrate. These effects induce chemical reactions leading to efficient etching of silicon within the laser-irradiated surface area, in combination with simultaneous deposition of carbon material outside. Because of the sensitive behavior of the photoinduced substrate surface temperature on the absorption conditions in the gas phase, model calculations were performed to improve the design of the system and to analyze the observed experimental results.
D119
Ya-Bing Li, Wei Wang and Yong-Lei Li
The adsorption behavior and mechanism of Janus green B (JGB) during a copper via-filling process were investigated by means of electrochemical measurements. Mass spectrometry and liquid NMR spectroscopy were employed to confirm the molecular weight and the structure of a JGB decomposition product (noted simply as product A). Meanwhile, quantum chemistry calculation was also used to investigate the active atoms in a JGB molecule. These results suggest that JGB can be easily reduced to product A on the cathode surface at very low polarizing potential, and desorb from the cathodic surface at the same time. As a result, the double bond
in the JGB molecule is broken and two hydrogen ions are added to each nitrogen atom, respectively. Compared to JGB, the adsorption strength of product A increases with the potential shifting negatively, and only product A can adsorb on the cathodic surface stably in a high overpotential range, which corresponds to the potential range used in practical copper via filling. It can be concluded that the reduced product A of JGB is the real leveler of copper via filling.
D125
Masaharu Nakayama, Yoshinori Kashiwa and Kazushi Suzuki
D131
N. Rybakova, M. Souto, Y. Andriyko, W. Artner, José Godinho and G. E. Nauer
Electrodeposition of
coatings in molten chloride-fluoride electrolyte
at
was investigated. PP techniques in forms of periodically reversed (PRC) and periodically interrupted current (PIC) were applied, instead of traditional dc procedure, which was also used for comparison, for the efficient deposition of the coatings onto molybdenum, stainless steel, and tungsten carbide substrates with different geometries and surface areas. The effect of current density, frequency, and pulse shape on the coatings properties was studied. It was found that the morphology and roughness of the deposit depend strongly on the deposition method and conditions. The coating with the lowest roughness
was obtained by PRC PP. The values of microhardness were in the range of
, depending on the pulse frequency in PIC electrolysis. The residual stresses are related to the frequency of deposition and vary in the range of
, being the minimum at pulse frequency of 20 and
. It was also found that the
coating decreases wetting of the steel surfaces by molten glass, which is of practical importance for tools working in these media.
D138
Z. L. Bao, S. Grist, S. Majumder, L. B. Xu, E. Jensen and K. L. Kavanagh
D146
Joshua W. Gallaway, Mark J. Willey and Alan C. West
Three copper-plating suppressors are examined in three-additive baths: a polyethylene glycol (PEG), a polypropylene glycol (PPG), and a triblock copolymer of the two. Bis(3-sulfopropyl)-disulfide (SPS) is found to transition each to a state of nonsuppression, i.e., accelerate each, at a rate dependent on the suppressor molecule, the SPS concentration, and, to a lesser extent, the suppressor concentration. Using a planar microscale working electrode
, the kinetic currents of the plating reactions are observed without the influence of ohmic resistance, revealing far higher current densities than previously reported. Potentiostatic and galvanostatic experiments of additive adsorption at short times,
, are compared quantitatively using a surface-blocking model to transform the data to effective surface coverage,
, vs time. A major difference is found in SPS acceleration between galvanostatic and potentiostatic experiments, with the rate of change in suppression being proportional to the current density. This results in a constant rate of change in
under constant current but a self-reinforcing rate of change in
at constant potential. A simple additive model is introduced to characterize the results.
D155
Wei-Ping Dow, Yong-Da Chiu and Ming-Yao Yen
A plating process for microvia filling by Cu electroplating, carried out in a plating bath without an accelerator but with a suppressor only, is proposed in this work. The seed layer of microvia used for subsequent Cu-filling plating is Au formed by electroless plating. The surface of the Au seed layer is modified in a solution containing bis(3-sulfopropyl)-disulfide (SPS) and various supporting electrolytes. This pretreatment is similar to the self-assembly monolayer (SAM) of a thiol molecule on a Au substrate. The coverage density of the adsorbed thiolate strongly depends on the presence or the absence of a supporting electrolyte and it crucially determines the filling performance of the plating process. The plating results demonstrate that the thiolate adlayer which is initially formed on the Au seed layer is transferable onto the surface of the plated Cu and then interacts with chloride ions to further facilitate Cu nucleation and growth. According to the results of the filling plating and the electrochemical analysis, an accelerating mechanism of SPS-SAM for copper electrodeposition and its transferring mechanism are proposed in this work.
Electrochemical Synthesis and Engineering
E75
Yuhong Cui, Yunhai Wang, Bin Wang, Haihui Zhou, Kwong-Yu Chan and Xiao-Yan Li
Physical and Analytical Electrochemistry
F55
Ryan West, Mira Josowicz, Jiri Janata, Isabelle Minet and Laszlo Hevesi
F60
J. A. Squella, L. J. Núñez-Vergara, R. Moscoso, J. Pezoa and J. Carbajo
Dielectric Science and Materials
G23
Chingchien Huang, Chun-Hu Cheng, Ko-Tao Lee and Bo-Heng Liou
Semiconductor Devices, Materials, and Processing
H225
Chun-Yuan Chen, Jung-Chuan Chou and Hsueh-Tao Chou
H229
K. Park, C.-H. An, M. S. Lee, C.-W. Yang, H.-J. Lee and H. Kim
H233
Mantavya Sinha, Rinus T.P. Lee, Anup Lohani, Subodh Mhaisalkar, Eng Fong Chor and Yee-Chia Yeo
H239
Musarrat Hasan, Rui Dong, Hyejung Choi, Jaesik Yoon, Ju-bong Park, Dong-joon Seong and Hyunsang Hwang
H243
P. F. Smet, N. Avci and D. Poelman
H249
J.-S. Park, M. Curtin, J. M. Hydrick, J. Bai, M. Carroll, J. G. Fiorenza and A. Lochtefeld
H255
Sonja Sioncke, Annelies Delabie, Guy Brammertz, Thierry Conard, Alexis Franquet, Matty Caymax, Adam Urbanzcyk, Marc Heyns, Marc Meuris, J. L. van Hemmen et al
H263
Maria Losurdo, Maria M. Giangregorio, Fabiana Lisco, Pio Capezzuto, Giovanni Bruno, Scott D. Wolter, Michael Angelo and April Brown
Oxide removal from InAs(100) surfaces was achieved using a combination of HF:methanol wet etching followed by atomic hydrogen treatment at a temperature as low as
without any stabilizing As flux. The process was monitored in real-time exploiting spectroscopic ellipsometry. Following this treatment, the surface morphology was found to be very smooth at the nanometer scale, with a reduced effective oxide thickness and no appreciable levels of elemental In and As. Furthermore, we demonstrate stability of such surfaces against oxide reformation.
H268
Ming-Kwei Lee, Tsung-Hsiang Shih and Po-Chun Chen
Both zinc oxide rods and zinc hydroxide slice were grown on gallium arsenide in the aqueous solution of zinc nitrate and hexamethylenetetramine. Incorporating with an appropriate concentration of nitric acid in the aqueous solution, the growth of zinc oxide rods or zinc hydroxide slice can be controlled. The cases with zinc hydroxide growth show very weak photoluminescence (PL). Much stronger PL can be obtained due to the transformation of zinc hydroxide into zinc oxide and quality improvement after thermal annealing. The case of only zinc oxide rod growth shows strong PL, but it shows optical degradation with a blueshift due to crystal cracking after thermal annealing. A reversible photoreductive deposition of copper ions
was used to evaluate the photocatalytic activity.
H272
Yan Cong, Bin Li, Shumei Yue, Liming Zhang, Wenlian Li and Xiao-jun Wang
H276
Chao-Cheng Lin, Ting-Chang Chang, Chun-Hao Tu, Wei-Ren Chen, Li-Wen Feng, Simon M. Sze, Tseung-Yuen Tseng, Sheng-Chi Chen and Jian-Yang Lin
An oxygen-incorporated Mo silicide layer was explored to form the Mo nanocrystals after rapid thermal annealing. Transmission electron microscopy showed the nanocrystals embedded in
. Charge-storage characteristics of Mo nanocrystals influenced by Mo oxide and its surrounding oxide were investigated through X-ray photoelectron spectroscopy and electrical measurement. X-ray photoelectron spectral analyses revealed a redox reaction in the oxygen-incorporated Mo silicide layer after rapid thermal annealing at a critical temperature. The memory window and retention were improved because of the reduction of Mo oxide. Furthermore, the double-layer nanocrystal structure was fabricated through the annealed stacked oxygen incorporated Mo silicide layer. A larger memory window and long retention were found for the double-layer nanocrystal structure. We used an energy band diagram to explain the difference in retention characteristics between single- and double-layer structures.
H281
Shun-Cheng Hsu, Dong-Sing Wuu, Xinhe Zheng and Ray-Hua Horng
H285
T. Ghosh, M. Dutta, S. Mridha and D. Basak
H290
L. I. Nieto-Gligorovski, S. Gligorovski, S. Tlili, X. Fu, B. Temime-Roussel and H. Wortham
Sensors and Displays: Principles, Materials, and Processing
J57
Soo Young Kim, Kihyon Hong, Ho Won Choi, Kwang Young Kim, Yoon-Heung Tak and Jong-Lam Lee
J62
Szu-Ping Chen, Jung-Chuan Chou, Tai-Ping Sun and Shen-Kan Hsiung
J67
Shigeki Kuroiwa, Jinping Wang, Daisuke Satake, Satoshi Nomura and Tetsuya Osaka
For completion of on-chip field effect transistor (FET) biosensors, it is essential to produce a reference FET instead of a reference electrode that uses an inner electrolyte. In this study, a light-addressable potentiometric sensor (LAPS) modified by a self-assembled monolayer (SAM) of octadecylsilane (ODS) was pH-insensitive
, but it was sensitive to ionic strength as was reported in polymer-gate FETs. Our purpose was to make clear the problems of the evaluation methods of ODS-SAM FETs concerning pH and ionic responses and the effect of the surface morphology to improve a reference SAM-FET. An ODS-SAM LAPS and FET were deposited under different conditions. pH and ionic responses, roughness measured by atomic force microscope, and contact angle (CA) were greatly changed by the difference in morphology of the ODS-SAM. ODS coagulation raised the CA. It is difficult to distinguish the ODS-SAM with and without ODS coagulation only by CA, but CA is utilizable for observing the state of hydroxyl groups on the surface without ODS coagulation. ODS coagulation caused the pH response with the ODS-SAM but decreased the ionic response of the LAPS. Controlling the surface morphology of the ODS-SAM is important to suppress the pH and ionic sensitivities for an in vivo applicable reference FET.
J73
C. H. Hsiao, S. J. Chang, S. B. Wang, S. P. Chang, T. C. Li, W. J. Lin, C. H. Ko, T. M. Kuan and B. R. Huang
J77
Yanqin Li, Yuhua Wang, Yu Gong and Xuhui Xu
samples doped with
,
, (
,
), (
,
), and (
,
,
) were prepared and studied. The
5d-4f emissions from two
sites in
were observed. However, only one single emission band at
was found in
. The energy transfer from
to
in
was demonstrated to be a multipolar interaction. It was found that
showed no afterglow.
showed some afterglow with a short persistence, and its afterglow could be enhanced by the incorporation of
. The triply doped phosphor
,
,
exhibited higher brightness and longer lasting time than that of
,
, which could be ascribed to more traps formed by the incorporation of
.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K37
Yu-Kai Han, Yi-Jang Lee and Pei-Chen Huang
K44
Ladislav Kavan, Shaik M. Zakeeruddin, Ivan Exnar and Michael Graetzel
The supramolecular assembly of Ru-bipyridine complex, coded Z-907Na, with single-walled carbon nanotube (SWNT) exhibits unique redox behavior, which is applicable for the nanotube wiring of
(olivine). Cyclic voltammograms of thin films of Z-907Na/SWNT reveal two pairs of peaks labeled
and
with formal redox potentials of ca. 3.6 and
vs
, respectively, indicating two surface-confined redox couples. The same behavior was also found for the Z-907Na adsorbed on carbon black, but not for the Z-907Na adsorbed on
or dissolved in the electrolyte solution. In these cases, a single diffusion-controlled voltammogram is observed, with one redox couple at ca.
vs
. The diffusion coefficients equal
(for Z-907Na adsorbed on
) or
(for Z-907Na in solution). An interpretation is suggested that the
peak is for a hydrophilic interaction, that is anchoring of Z-907Na to the carbon surface via carboxylic groups, and the
peak is for a hydrophobic anchoring, that is interaction with the carboxyl-free bipyridine ligand with the carbon surface. The existence of
peaks provides further insight into the nanotube wiring of
(olivine) using various nanotubes.
K51
Yung-Chiun Her, Chen-Tsan Tsai and Jer-Yau Wu
K55
Ying-Chien Fang, Sheng-Yuan Chu, Hung-Cheng Chen, Po-Ching Kao, In-Gann Chen and Chii-Shyang Hwang
K59
Kuo-Hao Lee and In-Gann Chen
Interdisciplinary Topics
P63
J. Dendooven, D. Deduytsche, J. Musschoot, R. L. Vanmeirhaeghe and C. Detavernier
The key advantage of atomic layer deposition (ALD) is undoubtedly the excellent step coverage, which allows for conformal deposition of thin films in high-aspect-ratio structures. In this paper, a model is proposed to predict the deposited film thickness as a function of depth inside a hole. The main model parameters are the gas pressure, the deposition temperature, and the initial sticking probability of the precursor molecules. Earlier work by Gordon et al. assumed a sticking probability of 0/100% for molecules hitting a covered/uncovered section of the wall of the hole, thus resulting in a stepwise film-thickness profile. In this work, the sticking probability is related to the surface coverage θ by Langmuir’s equation
, whereby the initial sticking probability
is now an adjustable model parameter. For
, the model predicts a steplike profile, in agreement with Gordon et al. , while for smaller values of
, a gradual decreasing coverage profile is predicted. Furthermore, experiments were performed to quantify the conformality for the trimethylaluminum
ALD process using macroscopic test structures. It is shown that the experimental data and the simulation results follow the same trends.
P68
Anthony D. Kammerich, Yasmin Srivastava, Kristen N. Hargett, Victoria S.R. Harrison and Judith F. Rubinson
As part of a long-range effort involving the design and fabrication of electrodes for in vivo use, we describe herein a method for the production of conducting polymer fibers with diameters on the order of a few micrometers. This method has been shown to be applicable to several different combinations of monomers [pyrrole,
-methylpyrrole, 3-methylthiophene, poly(3,4-ethylene dioxythiophene)], deposition substrates (Pt, stainless steel), and dopant ions (dodecyl benzene sulfonate, perchlorate, chloride, polymethylmethacrylate). Cyclic voltammetric characterization shows that the background current is minimal, and normal behavior is seen for the ferri/ferrocyanide couple with the exception of a slightly increased peak separation. An ancillary benefit of these studies is the production of extremely smooth films of these polymers, even in cases where the films are up to
thick.
P74
J. Agrisuelas, P. R. Bueno, F. F. Ferreira, C. Gabrielli, J. J. García-Jareño, D. Gimenez-Romero, H. Perrot and F. Vicente
The derivative of the voltabsommetric scans, together with previous nano-electrogravimetric and X-ray diffraction results, allow different electrochemical processes to be distinguished during the Prussian blue (PB) voltammetric scan. Potassium, proton, and hydrated proton counterions involved in PB electrochemistry are related here to the electrochemical reactions of specific Fe sites. Potassium counterions show two different sites for their insertion: one located in the crystalline framework and another in ferrocyanide vacancies. From the monitoring of electroactive Fe sites, the covalent-exchange model is suggested as one of the first approaches to explain the origin of the PB magnetic ordering observed at room temperature during voltammetric scanning.
Miscellaneous
S5
Laure Chevallier, Stefano Cordiner, Enrico Traversa and Elisabetta Di Bartolomeo
S6
K. C. Neyerlin, Greg Bugosh, Rhys Forgie, Zengcai Liu and Peter Strasser