ELECTROCHEMICAL SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
2009
Rosamaría Fong, Ulrich von Sacken and J. R. Dahn
Li/graphite and Li/petroleum coke cells using a
in a 50:50 mixture of propylene carbonate (PC) and ethylene carbonate (EC) electrolyte exhibit irreversible reactions only on the first discharge. These irreversible reactions are associated with electrolyte decomposition and cause the formation of a passivating film or solid electrolyte interphase on the surface of the carbon. The amount of electrolyte decomposition is proportional to the specific surface area of the carbon electrode. When all the available surface area is coated with the film of decomposition products, further decomposition reactions stop. In subsequent cycles, these cells exhibit excellent reversibility and can be cycled without capacity loss.
2014
Mark J. Isaacson, Frank R. McLarnon and Elton J. Cairns
2022
F. R. Foulkes, G. W. Archibald, Z. Ogumi and Z. Takehara
An ionized air reference electrode that uses a column of ionized air to establish electrical contact with an electrolyte was used to measure the ohmic voltage profile resulting from the flow of an applied current through a strip of Nafion 425 ion exchange membrane. The voltage profile thus obtained was used to calculate the conductivity of the reinforced Nafion solid polymer electrolyte and yielded a value consistent with the value reported in the literature. It was concluded that the ionized air reference electrode may be useful for use with solid polymer electrolyte systems.
2025
M. Farooque, A. Kush and L. Christner
Corrosion on the cathode or anode side of an electrochemical device is generally believed to be driven by the potential of that electrode. However, at times, unusually high localized corrosion has been observed in electrochemical cells having flowing reactants, such as fuel cells and flow batteries, which is not explainable by the “normal” electrode potential. This (observed) unusual corrosion is caused by the creation of two electrochemical cells in series within a single cell embodiment, where one cell becomes a power source and drives the other cell. The driven cell can have a depolarized counterelectrode, thus exposing the anode of the driven cell to a very high corrosion potential. Detailed mechanistic explanation and experimental verification of the mechanism are presented in this paper using a phosphoric acid fuel cell as an example.
2028
S. K. Yen and H. C. Shih
The introduction of hydrogen to a high chromium ferritic stainless steel by electrochemical charging has been studied. The slow strain rate technique
has been employed to elucidate the tensile behavior of the alloy responding to the effect of aging after cathodic charging. The critical concentration of hydrogen which changes the fracture mode from ductile microvoid coalescence to brittle transgranular cracking was determined through mathematical modeling, with the diffusivity and surface concentration of hydrogen obtained through permeation measurements with the sensitive Devanathan cell.
2031
J. E. Castle and J. H. Qiu
Samples of
,
, and a commercial 304 stainless steel were passivated in 0.1M sulfuric acid solution at constant potentials. The alloying effects of Mo and Ni on the corrosion property were studied in relation to their potentio‐dynamic polarization curves. A revolutionary new method of analysis in analytical chemistry, the inductively coupled plasma‐source mass spectrometry (ICP‐MS), was used to analyze the corrosion products in passivating solutions so as to explore the ion selectivity during dissolution and film formation processes. The selectivity factor S was defined and used to characterize the selective dissolution of Fe and/or Ni from the steels. The dissolution behavior of the Ni bearing steel changes with polarization time, from the initial selective dissolution of Ni to the final selective dissolution of Fe. Surface analyses of the passive films by x‐ray photoelectron spectroscopy (XPS) were also conducted in conjunction with ion beam sputtering to obtain depth distributions of alloying components. The selective enrichment of ions in the passive films were characterized by the enrichment factor f. A model based on the selective ionization was proposed to explain the enrichment of Ni in the metallic phase underneath the passive film. The dissolution kinetics as well as the film formation kinetics are discussed in terms of the charge balance during 69h polarization. Results from surface analyses of passive films by XPS are complementary with those from solution analyses by ICP‐MS.
2038
J. A. L. Dobbelaar and J. H. W. de Wit
Impedance measurements, performed in the active and active‐passive transition range, are explained by a simple mechanism. Four different time constants encountered in the impedance diagrams can be explained by diffusion controlled dissolution of chromium, hydrogen evolution, blocking of the surface by hydrogen, and passivation of the surface. In the passive region the potential dependent change in the “character” of the passive film results in another time constant in the impedance diagram. The surface can be seen as composed of two different areas. At one area diffusion controlled dissolution of chromium takes place, while at the other area blocking of the surface by hydrogen and passivation was found to occur. From the proposed mechanism the admittance expression was calculated and the parameters in the mechanism were determined.
2047
Chao‐Peng Chen and Jacob Jorné
A simple method is proposed for the determination of the fractal dimension during the electrodeposition of zinc by current integration. Under various experimental conditions,
, 2–12V, the patterns formed exhibit scale‐invariance characteristics. The fractal dimension of the two‐dimensional zinc deposits increases with the applied voltage (or applied current), while the morphology changes from highly branched random aggregate to the radial dense structure. A stochastic model based on the dielectric breakdown model (DBM) is proposed and the simulation analysis indicates that the relative resistivity between the zinc aggregate and the electrolytic solution can play an important role in the pattern transformation. A theoretical model based on the fractal theory is derived to estimate this ratio.
2052
C. Sheu and R. Weil
Chrome‐plating solutions dissolve copper, nickel, and steel substrates. In trivalent chromium solutions containing 40 ml/liter formic acid, the ions of the substrate metals codeposit to form alloy layers. When the formic‐acid content was lower, no alloy layers developed. The alloy layers are initially mostly amorphous and then become crystalline regardless of current density. The chromium deposits which formed on the alloy layers were crystalline when the current density was low and amorphous when it was high. The internal stress in the alloy layers is higher than in plain chromium deposits.
2056
Jean Horkans, David J. Seagle and I. ‐Chia Hsu Chang
2061
J. W. Graydon and D. W. Kirk
The codeposition of red phosphorus particles and copper from an electrolytic bath constitutes an attractive method for the production of phosphorized copper, which is the preferred anode material in bright acid copper electroplating. The effects of suspension concentration, current density, temperature, solution additives, and particle size on the amount of codeposition were determined. The behavior of this system is accurately modeled by the two‐step adsorption mechanism proposed by Guglielmi. The validity of the model was further confirmed by direct measurement of the surface concentration of particles. Codeposition was found to be independent of current density, temperature, and solution additives, and to increase linearly with particle size up to 15 μm. Finally, the ability to form smooth, coherent, thick deposits of uniform composition demonstrated the feasibility of using suspension electrodeposition to produce bulk phosphorized copper.
2067
P. Hülser and F. Beck
Polypyrrole powder was electrodeposited on aluminum electrodes after previous anodic polarization to form pits. The pores are filled with overoxidized polypyrrole. Aqueous
was employed as the preferred electrolyte. Point contacts at the entrance of the polypyrrole‐filled pits are provided, leading to a powdery PPy deposit. This opens the possibility for a totally iron‐free direct electrosynthesis of PPy powder for battery application.
2070
R. C. Bhardwaj, M. A. Enayetullah and J. O'M. Bockris
The proton activity of phosphoric acid and trifluoromethane sulfonic acid is determined at 150° and 90°C by electrochemical potential measurements. The transference number of ions required for the calculation of proton activity is determined by measuring the diffusion coefficients of ions using radiotracer techniques. The proton activity of TFMSA is determined to be higher than that of phosphoric acid at the temperature and concentration at which the acid fuel cell operates.
2076
Kiyoshi Otsuka, Yasuo Shimizu and Ichiro Yamanaka
2081
K. Akita, M. Taneya, Y. Sugimoto and H. Hidaka
2084
A. Honji, T. Mori and Y. Hishinuma
Platinum was highly dispersed on acetylene black by the reduction of chloroplatinic acid with methyl alcohol containing sorbitan monolaurate. When the preparation concentration of sorbitan monolaurate was 5.0 g/liter and the heat‐treatment temperature to decompose the residual sorbitan monolaurate in the catalyst was 500°C, the electrode fabricated with this catalyst showed the highest performance for oxygen reduction in phosphoric acid at 190°C. The residual surface‐active agent was carbonized on heat‐treatment and the pore distribution of the catalyst was changed. The time dependence of the change in platinum particle diameter was measured at 0.80V vs. RHE in phosphoric acid at 205°C. The particle diameter hardly changed during a period of about 400h.
2088
Signe Kjelstrup Ratkje, Tamio Ikeshoji and Kristin Syverud
A new thermodynamic theory of thermocells has been applied to cells with
electrodes, and a monovalent chloride compound in aqueous solution as electrolyte. All local heat and energy changes in the cells are calculated for the first time. The results show large heat effects at the electrodes, several orders of magnitude larger than the electric work obtained from the cell. Internal energy changes and Thomson effects are much smaller, however, comparable in magnitude to the electric work. This emphasizes the importance even of small effects. Heat effects are characterized by mass changes (thermodynamic heat changes) or by material changes (Peltier or Thomson effects). The Peltier effects show a systematic variation from about −21 kJ F−1 to 6 kJ F−1 as the cation changes from Li+ to Cs+. The transported entropy of
seems constant for concentrations below 0.1 mol kg−1. The transported entropy is largely dependent on the cation present. The variations can be correlated to inverse ionic radii. The theoretical reason why constant entropies appear to explain thermocell potentials for temperature differences up to 70°C is given. The theory suggests that a new experimental procedure should be used for determination of thermocell potentials. It is concluded that it is not feasible to measure directly the heat evolution in the electrolyte in these systems. Single‐ion entropies are furthermore shown inadequate for evaluation of thermal properties relevant to electrochemical engineering.
2095
P. K. Adanuvor, R. E. White and A. J. Appleby
A computer simulation of the oxygen reduction reaction in various carbonate melts has been carried out under steady‐state conditions on the basis of a proposed kinetic model which takes into consideration the autocatalytic reaction involving oxygen and other reducible oxygen species in the melt, and the neutralization of oxide ions by dissolved carbon dioxide. A simulation of the presence of (physically) dissolved oxygen, in the diffusion layer region of the melt, corresponding to the possible situation in porous electrodes, causes a significant enhancement in the polarization curves, particularly in the mass‐transfer control region. On the other hand, high levels of dissolved
in the melt reduce the current density in the mass‐transfer control region by reducing the concentration of active dioxygen ions, but enhance it considerably in the kinetic limiting (
neutralization) region. High rates of the autocatalytic and neutralization reactions display the same effects on the polarization curves as dissolved
and
, respectively, but to a lesser degree. Comparison of the simulated polarization curves in various carbonate melts indicates that Li‐rich melts show the best kinetic performance. On the contrary, the highest limiting currents are observed in K‐ or Na‐rich melts. Variation of the cation composition in Li/K carbonate melts indicates that melts of high Li‐content should give better kinetic performance.
2103
Sang‐Kyu Park and Demetre J. Economou
A simplified model for a time‐dependent plasma‐assisted chemical vapor deposition reactor was developed based on transport and reaction principles. The model equations were solved by the method of lines using collocation on finite elements for the spatial discretization. Emphasis was placed on the deposition rate and uniformity as a function of reactor operating conditions. A pulsed‐plasma reactor was analyzed, and compared to a continuous‐wave (CW) plasma reactor. Under conditions which would result in high depletion of the precursor gas in the CW reactor, the pulsed‐plasma reactor yielded improved uniformity, albeit the deposition rate was reduced. The effect of a recycle stream on both the CW and pulsed‐plasma reactors was also studied. For the CW reactor, recycle was most beneficial under conditions of low depletion of the precursor gas. For cases of intermediate depletion of the precursor gas, a CW reactor with recycle or a combination of pulsed‐plasma and recycle can result in nearly uniform deposit without sacrificing the deposition rate. Analytic solutions were derived for the CW reactor with recycle, and for a well‐mixed pulsed‐plasma reactor. The results apply equally well to pulsed‐plasma etching reactors conforming to the model assumptions and operating under corresponding conditions.
2116
Z. Mao, P. Adanuvor and R. E. White
A mathematical model is presented for a high temperature
electrolyzer. It is shown that the maximum current in this type of a cell is determined entirely by the transport rate of sulfide ions through the separator. It is suggested that this model could be used to determine the feasibility of various designs for this electrolyzer.
2124
Thomas C. Franklin, Jerald Darlington and William K. Adeniyi
It was shown that an active intermediate suitable for catalyzing the anodic destruction of carbon tetrachloride could be electrolytically generated by oxidation of barium peroxide in aqueous sodium chloride solutions containing cationic surfactants. Voltammetric studies showed that
for formation of the intermediate was close to one and it was concluded that the intermediate was barium Superoxide. Quantitative analysis showed that the intermediate reacted with water to produce barium oxide and hydrogen peroxide.
2126
Dominique L. Piron, Normand Massé and Louis Ph. Bérubé
Laboratory‐scale experiments of zinc electrowinning under periodical reverse current (PRC) were carried out in acidic sulfate solutions. To study the effects of lead impurities on the zinc cathode, 0.3–15 mg/l of lead were added to the electrolyte. A square wave of current was used to produce the PRC. Current densities of 500 and 1500 A/m2 were investigated under both direct current and PRC. In the case of PRC, the direct and reverse pulses had respective durations of 100s and 0.1–1.0s. The current density of the reverse pulse was set at half the value of the direct pulse. Comparisons were made with conventional dc electrolysis. The presence of 5 mg/l of lead lowered the current efficiency in dc from 94.1 to 93.2%, while in PRC it raised it from 93.2 to 97.6%, using a reverse pulse duration of 0.1s. Correlation between the current efficiencies and the presence of the crystallographic plane (101) was also observed. It suggests that lead in the zinc deposit and the use of PRC influence the crystallographic growth of the zinc deposit. The presence of plane (101) increases the oyerpotential of hydrogen evolution on zinc, and this results in a higher current efficiency. A way of obtaining the beneficial plane is to use PRC and lead in the electrolyte together.
2132
Kiyoko Takamura and Fumiyo Kusu
The surface behavior of neurotransmitters, their agonists and antagonists on a gold electrode/phosphate buffer solution was studied by specular reflection measurement. There was adsorption of the following neurotransmitters: γ‐aminobutyric acid, glycine, β‐alanine, dopamine, norepinephrine, epinephrine, acetylcholine, glutamic acid, and aspartic acid in the potential range of −200 to 200 mV vs. the point of zero charge. The potential profiles of adsorption between inhibitory and excitatory neurotransmitters were noted to differ. Their antagonists were adsorbed onto the electrode more strongly than the neurotransmitters. The adsorption potential profile provides clarification of the electrostatic interactions between the receptor site and neurotransmitter or related drugs.
2135
Robert J. Mammone and Michael Binder
Dielectric properties (dielectric constants, dielectric losses, conductivity, and voltage breakdown strengths) of electrochemically formed poly‐N‐methylpyrrole (PNMP) have been studied as a function of the anions used in aqueous supporting electrolyte during electrochemical polymerization. Depending on the electrolyte anion and synthesis conditions, dielectric properties of resulting PNMP films varied considerably.
2139
Tetsuya Osaka, Toshiki Nakajima, Katsuhiko Naoi and Boone B. Owens
Polyaniline films electrodeposited from acidified nonaqueous organic media were investigated for their electropolymerization behavior and charge‐discharge characteristics. The solution system used for the electropolymerization of polyaniline film was
acidified propylene carbonate, which was previously found to be the best system for the preparation of a highly electroactive conducting polymer film. Electroactive polyaniline films only form in solutions where the mole ratio of acid
to aniline monomer is greater than one. As the acidity is increased, the resultant polyaniline film exhibits greater electroactivity and better charge‐discharge performance of Li/polyaniline cathode cell. This effect may be ascribed to the high current efficiency in electro‐oxidative polymerization and high redox reversibility of PAn films prepared in the high acid content solutions.
2143
Jeffrey B. Richard, Mario Aparicio‐Razo and David K. Roe
2147
Susumu Kuwabata, Jiro Nakamura and Hiroshi Yoneyama
The conductivity of polypyrrole films doped with p‐phenol sulfonate decreases with increasing pH of aqueous solutions in which the films are immersed. A linear relationship is established between the relative ratio of the conductivity change and the degree of dissociation of hydroxyl groups of p‐phenol sulfonate doped in the film, indicating that the decrease in the conductivity results from an increase in bindings of positive charges of polypyrrole with phenoxide ions produced by dissociation of hydroxyl groups of the dopant. The formation of the phenoxide ions accompanies the incorporation of electrolyte cations into the film to compensate the generated negative charges. The rate of the conductance change caused by changing solution pH is then controlled by the diffusion rate of electrolyte cations in the polypyrrole films and is high for cations of small ionic radius.
2151
Stephen E. Creager and Marye Anne Fox
The ability of poly(p‐xylyl‐viologen) adsorbed on gold to block solute transport is strongly affected by film solvation and the electrolyte counterion. Permeability measurements with hydroxymethyl ferrocene and
imply controlled solute permeation/diffusion rather than a partially blocked electrode. Electrostatic effects on calculated double layer potentials adequately rationalize the observed decrease in heterogeneous electron transfer rate.
2157
A. Bandi
2161
C. Alonso, R. C. Salvarezza, J. M. Vara, A. J. Arvia, L. Vazquez, A. Bartolome and A. M. Baro
A simple method is presented for measuring the surface diffusion coefficients of Au and Pt atoms at electrodispersed electrodes of the same metals in contact with
. The technique is based upon the time dependence of the surface roughness factor of electrodispersed metal overlayers. The method requires a model for the surface roughness of the metal structure. The model is deduced from microscopic measurements by a STM integrated into a conventional SEM microscope. This allows the relationship between the roughness factor and the area of the surface structure to be obtained. For Au and Pt in contact with an electrolyte solution, the values of our diffusion coefficients are higher than those reported in vacuum at the same temperature.
2166
Xuekun Xing, Daniel A. Scherson and Cecilia Mak
2175
U. G. Akano, W. W. Smeltzer, D. A. Thompson and J. A. Davies
The hydrogen evolution reaction in aqueous 30 weight percent
electrolyte at 80°C was investigated for Ni‐Pd surface alloys, produced by the ion beam mixing technique. Surface alloys, containing 55–90 atom percent (a/o) Pd, were produced by subjecting evaporated layers of Ni and Pd on Ni substrates to 120 keV Ar+ ion bombardment; the alloy composition vs. depth was monitored by Rutherford backscattering using 2 MeV 4He+ ions. Polarization of the electrodes was determined by potentiodynamic techniques at a sweep rate of 2 mV/s. Unbombarded Ni and Ni/Pd cathodes exhibited only a single Tafel region; the alloy electrodes fabricated by ion beam mixing, on the other hand, exhibited at least two Tafel‐type regions, a low slope 40–50 mV/decade region between 0 and −0.1V and an increasing slope at larger negative potentials. The superior current‐potential behavior corresponding to most effective catalytic activity of the cathodes was characterized by the existence of the low Tafel slope region on the alloys which was most prominent in the case of the Ni‐55 a/o Pd cathode.
2181
F. Bénière, J. Corish, M. E. G. Lyons, T. McCabe and A. Morin
2185
Ramakant Kumar, I. K. Varma and A. B. Bhattacharyya
This paper describes the effect of sodium perchlorate
on the properties of polypyromellitimides. Low‐temperature solution polycondensation reaction of pyromellitic dianhydride and 4,4′‐diaminodiphenyl ether was used for the preparation of poly(amide‐acid) solution in dimethyl formamide
. Films containing 0.5, 1.0, 2.0, 3.0, 5.0, and 10.0%
were prepared by solution casting of poly(amide‐acid) from the DMF solution. Cyclodehydration to polyimide was done by heating the films in nitrogen atmosphere for an hour each at 100°, 200°, and 250°C. The IR, TG, and DSC studies indicated that in the presence of
, the cyclodehydration reaction of poly(amide‐acid) is reduced. The electrical conductivity and dielectric behavior of polyimide films as functions of temperature and field were studied. Significant decrease in resistivity of polypyromellitimide films was observed in presence of
.
2189
Z. Mao, R. E. White, B. Dandapani, A. Anani, S. Srinivasan and A. J. Appleby
TECHNICAL NOTES
2194
S. W. Orchard, Y. Sato, J. ‐P. Schoebrechts and G. Mamantov
2196
H. S. Isaacs and A. J. Davenport
SOLID-STATE SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
2199
Nitin Parekh and Jim Price
Various metallization schemes are used to provide conducting layers in IC fabrication. X‐ray fluorescence spectrometry has been utilized to examine the chlorine and fluorine levels in some of these metallization schemes after patterning and etching. The metallization systems investigated include Al‐Si and Al‐Si‐Cu, with and without
. The corrosion characteristics of these metallizations are found to be predominantly a function of chlorine levels. The galvanic cell effects of the Cu and
with Al are not significant within the range of etch processes investigated. The effect of different in situpassivations as well as various postetch treatments are presented. The residual chlorine levels at various stages of the pattern definition process are also presented.
2203
F. Ferrieu and J. H. Lecat
In the visible range from 250 to 900 nm, a variety of spectroscopic ellipsometers are presently available from different manufacturers. Some of these instruments can be used off‐line for thin film characterization, but other instruments are fully compatible with vacuum systems and the in situ study of phenomena such as growth kinetics, thin film deposition processes, and surface adsorption effects. A review of the existing spectroscopic ellipsometers is given as well as an up‐to‐date ellipsometric configuration still under development, which involves three polarizers. The relative accuracy of this latter instrument is discussed. A review of the applications of this technique in the case of bulk or layered materials and of the problems encountered in the microelectronics industry is given. Spectroscopic ellipsometry can also be performed in the infrared range. Some first results, measured with a prototype of this instrument, are shown in order to demonstrate the degree of sensitivity of this technique.
2209
S. Nguyen, D. Dobuzinsky, D. Harmon, R. Gleason and S. Fridmann
Plasma‐ and thermal‐assisted chemical vapor deposited (CVD) tetraethylorthosilicate (TEOS) oxide films were deposited on silicon substrates using a single‐wafer reactor. The deposition kinetics of both plasma and thermal CVD processes were studied as a function of temperature. Film properties and bonding structure were analyzed for as‐deposited and annealed films using Fourier transform infrared spectroscopy (FTIR), Auger, x‐ray photoelectron spectroscopy (XPS), and nuclear reaction analysis (NRA) techniques. The thermal TEOS films were found to be more porous and to contain more hydrogen, but were more conformal than plasma‐deposited TEOS films. Without a plasma, thermal temperatures can assist gas‐phase reactions between ozone and TEOS (oxidation) to form conformal oxide films at as low as 200°C. With a plasma, both gas‐phase and subsequent surface CVD reactions between TEOS, ozone, and oxygen are substantially enhanced, thus result in CVD films with higher quality.
2215
Joon Ho Koh and Seong Ihl Woo
2222
J. N. Chiang and D. W. Hess
A stainless steel screen placed directly over the substrate in an RF glow discharge significantly altered plasma deposited (PD) silicon nitride film chemical composition and structure as measured by x‐ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy. Changes in film composition were more pronounced for PD silicon nitride films formed using
as the nitrogen source gas rather than
. An increase in the N:Si ratio was observed for all films deposited using the screen. This change in N:Si ratio was also reflected in an increased N‒H and decreased Si‒H bonding structure. These results are similar to those obtained previously in triode and remote plasma reactors, thereby suggesting common deposition mechanisms for films deposited in different reactor configurations.
2227
Paul E. Riley and Paul Bayer
The characteristics of
plasmas which are used to etch composite layers of sacrificial photoresist and underlying
have been examined with experimental design and modeled empirically by response‐surface methodology using a Lam Research Autoetch 480 single‐wafer system. The effects of variations of process gas flow rates for
(150–200 sccm) and
(0–50 sccm), reactor pressure (900–2000 mtorr), and interelectrode spacing (4–6 mm) on the etch rates of
and photoresist were explored at fixed radio frequency power (500W at 13.56 MHz) at
. Variation in spacing shows different effects for these two materials; whereas the
etch rates generally increase with increasing spacing as the other parameters are varied, the photoresist etch rates exhibit more complex behavior. At the lower spacing of 4 mm, neither film has a measurable etch rate for low settings of the other variables. The
etch rates are virtually constant with increasing
flow rate for low, middle, and high settings of the other variables. At low settings of the other variables, the photoresist etch rates are zero over the range of
flow rates but increase with increasing
flow rates for middle and high settings of the other variables. At a spacing of 4 mm, the etch rates of both films are negligible over the range of
flow rates and the range of reactor pressure. At larger spacings the etch rates of photoresist increase with increasing
flow rate, while the etch rates of
are similar for middle and high settings of the other variables over the range of
flow rates. Process optimization using the empirical models to attain suitable etch rates for both films for planarization of a composite layer of photoresist and
with high etch uniformity was achieved at 500W of RF power, 1450 mtorr, 150 sccm of
, 0 sccm
, and a spacing of 5.5 mm. Hence, for a
plasma with this reactor adequate planarization is obtained without the use of
. The addition of small concentrations of
to a
plasma resulted in increasingly higher etch rates for photoresist as the process progressed.
2231
Masao Yamada, Kazuaki Kondo, Masafumi Nakaishi, Jinko Kudo and Kenji Sugishima
2242
Masao Yamada, Masafumi Nakaishi and Kenji Sugishima
The addition of an atom having different bonding radii to a matrix film is an effective method for changing the stress of the film. In a plasma‐enhanced CVD of BN, it is difficult to obtain tensile stress except for extremely boron‐rich films. The controllability of tensile stress in BN film was improved by introducing a small amount of carbon into the BN matrix, using plasma‐enhanced CVD between 400° and 500°C. We obtained transparent films with high Young's modulus and tensile stress. The radiation resistance of BNC deposited at 400°C was improved five times better than that of BN deposited by low‐pressure CVD at similar temperatures.
2246
Lynnette D. Madsen and Louise Weaver
The low pressure chemical vapor deposition (LPCVD) of in situ doped silicon from disilane
and phosphine
was investigated using response surface methodology experimental design. TEM and associated analytical techniques were employed in characterizing films deposited over the range of 475°–700°C. Polycrystalline films with a resistivity of ∼770 μΩ‐cm after a 850°C, 30 min anneal with less than 5% thickness variation were deposited at approximately 60 Å‐min−1 over 100 mm wafers.
2252
Masahiro Akiya, Hiroaki Nakamura and Yosinobu Arita
This paper describes the high electromigration resistance, absence of silicon nodule formation, and high surface specularity characteristics of sputtered magnesium‐aluminum‐silicon (Mg/Al‐Si) metal systems. Stripe samples were tested at a current density of
, and the activation energy for 5.2% Mg/Al‐Si alloy was 0.9 eV. Silicon nodule formation and hillock formation during heat‐treatment were greatly suppressed at high Mg concentrations. Specular reflectance was 92% for alloys containing over 1.6% Mg.
2257
T. E. Kazior
The use of implant damage to provide electrical isolation between devices on
substrates was studied. Singly ionized oxygen and singly and doubly ionized boron ions were implanted into bulk doped
substrates at various doses and energies. Carrier concentration profiles of the damage region were used to determine the characteristics of the ion damage profiles (i.e., damage peak and carrier removal per incident ion). These measurements were performed on as‐implanted wafers and on samples subjected to temperature cycling that simulates routine wafer processing. The results indicate that both boron and oxygen remove nearly 100 carriers per incident ion and that the damage produced by oxygen ions is more temperature stable. Isolation implants were subsequently performed into wafers whose active layers were formed by implantation and annealing. Leakage current was measured as a function of isolation implant dose. Results indicate that for blanket implanted active layers a minimum in leakage current exists for isolation doses approximately equal to one‐tenth of the active layer implant dose. Increasing the isolation dose leads to large increases in leakage current. A simple method for tailoring the isolation implant profile to the active layer profile is presented.
2261
Kiyonori Ohyu, Yasuo Wade, Shinpei Iijima and Nobuyoshi Natsuaki
Highly reliable thin silicon dioxide layers are grown by rapid thermal oxidation on heavily phosphorus doped poly‐Si layers. Oxide layers as thin as 5 nm are grown with high controllability by choosing appropriate oxidation temperature and time. Breakdown field is improved by about 40%, as compared with that of oxides grown by conventional furnace oxidation. Time‐dependent dielectric breakdown characteristics of the oxide layers under high electric field are also improved by one order of magnitude. The major reason for the high reliability is attributed to the improvement of the interface morphology of poly‐Si and silicon dioxide. Rapid thermal oxidation should be the key technology for the sub‐μm ULSI DRAMs in stacked as well as in trench capacitor cell fabrication.
2266
J. M. Eldridge, J. O. Moore, G. Olive and V. Dunton
The thermal oxidation characteristics of
films were studied for compositions from
and varying hydrogen concentrations. The carbide films were plasma‐deposited onto oxidized Si substrates, using two differently configured deposition systems; silane, methane, and argon gas mixtures; and, temperatures from 200° to 600°C. The films were oxidized in either dry oxygen or air (with approx. 1 volume percent water) for times between 1 and 270h and temperatures from 500° to 900°C. The resulting oxide surface layers were characterized by etch rate, profilometry, XPS, and RBS techniques and were determined to consist of virtually stoichiometric
at the outermost surface with perhaps small islands of unreacted carbide remaining near the inner interface. Oxidation rates were found to increase rapidly with increasing C and H concentrations and were always much larger than those of sintered, sputtered films of stoichiometric
. The oxidation results were found to fit reasonably well to a mixed linear‐parabolic time dependence. This kinetic analysis suggested that the large observed increases in the linear and parabolic rate constants with decreasing
could be attributed to preferential attack on C‒H bonds which are more prevalent in the graphitic, C‐rich films than in the tetrahedrally coordinated, Si‐rich ones.
2271
D. M. Speckman and J. P. Wendt
2276
F. M. Tranjan, S. M. Bobbio, T. D. DuBois, R. G. Frieser, S. K. Jones and S. P. Ashburn
Conventional photoresists have been modified by the incorporation of a phosphorus‐containing compound, i.e., phosphonitrilic chloride trimer
. The modification was achieved by simply dissolving
(PNCT) in conventional photoresists. The phosphorus concentration varied from 5 weight percent (w/o) to 12 w/o in the modified photoresist films. These films formed a barrier layer when exposed to oxygen plasmas. After the layer was formed, no measurable resist etch rate could be detected. The resolution and mechanical properties of the modified resist films were essentially unchanged, although an increase by a factor of 1.5 in the exposure threshold was observed. Features of less than 1 μm lines and spaces were anisotropically etched in polyimide masked by this photoresist. Furthermore, metal lift‐off structures have been obtained using a bilayer process employing the modified resist.
2280
Suresh P. Venkatesan, Isaac Trachtenberg and Thomas F. Edgar
2291
U. S. Kim, C. H. Wolowodiuk, R. J. Jaccodine, F. Stevie and P. Kahora
2297
Stefan Bengtsson and Olof Engström
Silicon/silicon interfaces were prepared by wafer bonding using the silicon‐to‐silicon direct bonding method at temperatures below 1000°C. The bonded samples were prepared using wafers with hydrophilic and hydrophobic surface properties. The density of voids at the bonded interface and the electrical properties of the interfaces were investigated. The density of voids in hydrophilic samples was mainly determined by the initial contacting of the wafer surfaces at room temperature. The influence of heat‐treatments was weak. Compared to hydrophilic samples, hydrophobic samples were held together at a smaller fraction of the surface area before heat‐treatment. During short heat‐treatments, this fraction increased and a large number of point‐shaped voids was generated. These voids, probably due to enclosed gas, disappeared with an activation energy of 2.3 eV when the annealing proceeded. After long annealing times, no significant difference in the density of voids between hydrophilic and hydrophobic samples was found. Silicon/silicon interfaces with excellent electric properties were prepared by using hydrophobic surfaces at temperatures in the range 700° to 1000°C. No influence of the bonded interface on the current‐voltage characteristic of n‐type/n‐type samples prepared at 700°C for 5 min was found. Directly bonded p+n junctions prepared at 700°C for 5 min exhibited ideality factors
at small forward bias. A correlation between n factors and the density of states in the bandgap was found. Attempts to reduce the bonding temperature considerably below 700°C were thwarted by decreasing mechanical strength at the bonded interface.
2303
I. Nakao, H. Umimoto, S. Odanaka, T. Ohzone and H. Esaki
Wet cleaning of deep trenches, 4 μm deep and 0.5 μm wide, was studied using a two‐dimensional wet cleaning simulation including both flow and diffusion effects. It has turned out that the diffusion effect is a dominant factor during wet cleaning. When the flow velocity of the rinse water increases, the rate at which solution in trenches is replaced becomes higher. In our simulation, the solution in the deep trench is diluted to 1 ppm by rinse water within several seconds. This result shows that deep trenches with submicron width can be cleaned by a wet cleaning process. Uniform etch rates of oxide in deep trenches suggest the diffusion mechanism is predominant.
2306
P. Normand, D. Tsoukalas, N. Guillemot and J. Stoemenos
2313
William G. Breiland and Michael E. Coltrin
Deposition rates are presented for silicon from silane in a helium carrier gas using a tubular CVD reactor with a two‐dimensional flow geometry. Measured surface‐temperature profiles, inlet gas velocities, total pressures, and silane/helium concentrations are reported, providing exact boundary conditions that can be used in a two‐dimensional numerical CVD model. Comparisons are made between this data and two variations of a model by Coltrin, Kee, and Miller in which different empirical expressions for the silane and disilane reactive sticking coefficient are used.
2319
X. Liu, E. A. Irene, S. Hattangady and G. Fountain
2323
V. J. Silvestri, K. Nummy, P. Ronsheim, R. Bendernagel, D. Kerr, V. T. Phan, J. O. Borland and J. Hann
ULSI quality silicon epitaxial films as thin as 0.6 μm have been grown using dichlorosilane at temperatures as low as 850°C and pressures as low as 10 torr in commercially available cylindrical epi reactors. Removal of the substrate surface native oxide by a 5 min hydrogen bake has been observed down to 850°C, 10 torr. In addition, very low defect levels and excellent device characteristics have been measured in the epitaxial films. The results were observed on both 125 and 200 mm substrates.
2327
Rafael Tovar, Miguel Quintero, Champa Neal and John C. Woolley
2331
Gunnar R. Dieckmann, Arthur B. Ellis and Eric E. Hellstrom
Electroluminescence (EL) cells have been constructed with the layered, ionically conducting solid, hydrogen uranyl phosphate,
(HUP), as the emissive medium. With ac excitation, both uranyl emission and molecular nitrogen plasma emission are observed, with the latter appearing to excite the former; the uranyl EL spectrum matches the photoluminescence spectrum of the solid. Similar results were obtained with fully substituted sodium (NaUP), magnesium
, and pyridinium (pyHUP) derivatives of HUP. For all of these solids, the dependence of the EL intensity on sample thickness, ac frequency, and applied voltage has been determined. Typical operating conditions are 1.5–3.0 kV at 0.2–4 kHz. Impedance measurements permitted acquisition of dielectric constants and ionic conductivities for these solids, both of which decrease in the order
. A model describing the dependence of EL intensity on cell parameters is presented.
2336
Jean A. Siracuse, Jan B. Talbot, Esther Sluzky, Teresa Avalos and Ken R. Hesse
In a fundamental study of the cataphoretic deposition of phosphor from an isopropanol (IPA) solution, the electrophoretic properties of the phosphor particles, the dissociation of magnesium and lanthanum nitrate salts in IPA, and the reactions of Mg2+ and La3+ were investigated. It was determined that Mg2+ and La3+ near the cathode react to form an adhesive hydroxide matrix which binds the phosphor particles to the substrate. The degree of dissociation of the nitrate salts in IPA determined from conductivity measurements is less than a few percent. The conductivity of the plating bath increases with successive depositions due to the absorption of water from air by IPA, which also increases the ionization of the nitrate salts. From zeta potential measurements, the phosphor itself is negatively charged and only an extremely small concentration of ions is required to charge the particles positively in the bath. Using the zeta potential measurements to calculate electrophoretic velocity, a model to predict the deposition rate of phosphor was developed and was found to be in good agreement with experimental results when the settling of the phosphor was taken into account.
2340
Ryuichi Morimo, Takanori Mizushima, Yasuo Udagawa, Noriyoshi Kakuta, Akifumi Ueno, Hiroaki Okumura and Hiroshi Namikawa
2344
R. P. Vasquez, B. D. Hunt and M. C. Foote
Wet chemical techniques are described for treatment of
surfaces, which result in the formation of native compounds known to have little or no reactivity to water. Suitable native compounds include
,
,
,
,
, and the oxalates. Formation of surface layers in which these nonreactive native compounds are major constituents is verified with x‐ray photoelectron spectroscopy (XPS) measurements on
films treated with dilute solutions of
,
,
,
, or
. No significant changes are observed in the XPS spectra when the sulfide, sulfate, or oxalate films are dipped in water, while the iodide and fluoride films show evidence of reaction with water. X‐ray diffraction measurements show that the superconducting phase is absent in the sulfide film, but is unaffected by the oxalate and sulfate treatments.
TECHNICAL NOTES
2350
J. M. Sung, C. Y. Lu, L. B. Fritzinger and K. H. Lee
ACCELERATED BRIEF COMMUNICATION
2353
Kenneth E. Creasy and Brenda R. Shaw