ELECTROCHEMICAL SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
469
Ryoji Kanno, Yasuo Takeda, Kazuaki Takada and Osamu Yamamoto
474
K. Harris, R. J. Hill and D. A. J. Rand
The crystalline and amorphous component phases of positive plates taken from lead‐acid batteries in simulated electric‐vehicle service were examined by quantitative XRD analysis. They were compared with independent determinations from electrical measurements and wet chemical analysis. Changes in temperature, discharge current, the ratio of
, and the amount of amorphous material are correlated with the capacity and cycle life of the batteries.
483
E. J. Taylor, G. A. Shia and D. T. Peters
487
E. J. Taylor, G. A. Shia and D. T. Peters
492
K. A. Klinedinst
The development of a practical sulfuryl chloride‐based lithium/oxyhalide cell technology has been delayed by anode corrosion and cathode polarization problems encountered when the standard oxyhalide cell electrolyte and cathode formulations are used. The anode stability problem can be significantly alleviated by the use of a reverse polarity cell design, the substitution of
for
as the electrolyte salt, and the addition of a suitable cosolvent (
or
). Further, at least under ambient temperature storage and discharge conditions, anode passivation is completely absent with hermetically sealed
cells of this type. Cathode polarization can be reduced most effectively by the use of a supported platinum cathode material. This cathode material also results in substantially increased discharge capacities, although the overall reaction stoichiometry is unaffected by the catalyst. Finally,
thermal decomposition measurements indicate that, as the temperature of the
electrolyte in a hermetic cell is increased from 25° to 80°C, the pressure differential across‐the cell case will rise to about 3.5 atm. Then, as the temperature is decreased to a lower value, the pressure differential will also decrease to the equilibrium value characteristic of that lower temperature, indicating a thermally stable, reversible system.
499
Z. Szklarska‐Smialowska and W. Kozlowski
505
G. W. Kammlott, J. P. Franey and T. E. Graedel
Although it is widely recognized that copper alloys are subject to sulfidation upon exposure to the atmosphere, the information available on the sulfidation rates of these alloys has come largely from field exposures under uncontrolled conditions. To gain more definitive information on the rates and processes involved in atmospheric sulfidation of copper alloys, we exposed nine copper alloys (brasses, nickel‐substituted brasses, and other common compositions) to low concentrations of hydrogen sulfide in humidified air. Among the specific results are the following. (i) The resistance to sulfidation of the brasses was 50–100 times better than that of pure copper. (ii) The substitution of nickel for part or all of the zinc produces alloys even more resistant to sulfidation for low to moderate exposures; at longer exposures their behavior is mixed. (iii) Beryllium copper and phosphor bronze are somewhat more resistant to sulfidation than copper except for long exposures, when all three behave similarly. (iv) A silicon bronze sulfidized more rapidly than copper for most exposure periods. (v) Alloying copper with 10% aluminum yields an alloy with a sulfidation resistance nearly as good as the brasses. These results are discussed in conjunction with the information available on oxide growth on these alloys, and it is demonstrated that the sulfidation resistance of the alloys is quite similar to their resistance to oxidation, once an initial oxide film has formed. The degree to which the surface oxide film inhibits copper diffusion is thus reflected in the oxidation and sulfidation behavior of a given alloy. The results indicate that the performance in sulfidizing environments of equipment containing copper alloy components or parts can thus be markedly influenced by the particular alloys selected by the physical designer.
511
G. W. Kammlott, J. P. Franey and T. E. Graedel
In order to assess quantitatively the sulfidation characteristics of industrially used alloys of copper, we have exposed a variety of copper‐nickel‐tin alloys as well as the pure metals to hydrogen sulfide in humidified air. The thicknesses of the resulting sulfide films were then determined. Nickel and tin were very resistant to sulfidation and copper alloys containing at least a combined total of 8% of these metals were resistant as well. The rate of sulfidation for the 92 Cu/4 Ni/4 Sn alloy is decreased with respect to copper by a factor of about four for moderate exposures. The rate continues to decrease as more alloying metal is added to the copper, reaching an equivalent rate of <0.2 nm
for an alloy of 78 Cu/15 Ni/8 Sn in a typical field environment. The content of nickel in the alloy appears to be more important to the inhibition of sulfidation than the tin content. A spinodal alloy after heat‐treatment is less resistant to sulfidation than the same alloy as cold‐worked. Annealed 725 alloy (89 Cu/9 Ni/2 Sn) is more prone to initial sulfidation than is the same alloy when work hardened. The results of this and earlier work demonstrate that alloys of copper containing at least 10% of any of the common alloying metals are some thirty times more resistant to sulfidation than pure copper.
515
James G. Foggo III, Douglas B. Nordman and R. L. Jones
522
B. Löchel, H. ‐H. Strehblow and M. Sakashita
530
L. D. McCormick, N. S. Wheeler, C. R. Molock and C. L. Chien
Amorphous iron‐zirconium alloys, ranging in composition from
to
, have been studied by anodic polarization and passivation decay in 1N sulfuric acid. The results showed a compositional enhancement of corrosion resistance with increasing zirconium concentration. Auger electron spectroscopy indicated that exposure to the sulfuric acid solution enhances the surface zirconium concentration with respect to the bulk of the exposed alloy and also with respect to the as‐deposited surface composition. X‐ray photoemission spectroscopy shows that the passive film is a mixture of zirconium oxides and hydroxides and iron oxides and hydroxides.
534
C. J. McClanahan and D. A. McQuarrie
An extension of the mean spherical approximation, MSA, is used to study the restricted primitive model of the electrical double layer involving multivalent ions. Comparisons are made between this approximation, the MSA, and the Poisson‐Boltzmann approximation.
540
Richard Scheps
The thickness of polymethylmethacrylate (PMMA) films deposited in solution on
is measured by ellipsometry to determine its dependence on terminal spin speed. The PMMA solution behaves as a steady‐state Newtonian fluid. Film thickness in excess of the periodic thickness is measured by combining data taken at three angles of incidence; a procedure for applying this technique is discussed. The main feature consists of assigning the film index from data taken at the incident angle where the ellipsometer readings are most sensitive to film index, and using this index in determining the film thickness at the other two angles. The basis supporting this procedure is presented, and the dependence of the ellipsometric model on uncertainties in the assignment of film and substrate optical constants is discussed specifically in terms of its effect on the three‐angle technique.
543
N. A. Godshall, I. D. Raistrick and R. A. Huggins
The interdependence of thermodynamic parameters, phase equilibria, and electrochemical measurements can be used as a powerful tool in the development of high specific energy cells. These principles were used in the analysis of electrochemical experiments performed on ternary lithium‐transition metal‐oxide
positive electrodes. The free energies of formation of
,
,
, and
were found to be −178.21, −399.88, −154.18, and −131.62 kcal/mol at 400°C. The electrochemical displacement reactions were found to be reversible in
molten salt cells over a range of 0.0–3.0 Li equivalents per mol at current densities of 5–15 mA/cm2. The equilibrium potential vs. Li was found to be a logarithmic function of the calculated oxygen partial pressure for any tie triangle in which
is present, or for any tie triangle containing ternary oxide phases
which are only marginally stable with respect to
and the relevant binary oxides
. Compounds with oxygen partial pressures above 10−25 atm were found to be unstable in
electrolyte at 400°C.
550
P. Salvador, C. Gutiérrez, G. Campet and P. Hagenmüller
The influence of lattice defects produced by mechanical polishing of the surface upon the photoelectrochemical properties of polycrystalline
anodes was investigated. The lattice defects were correlated to various subbandgap energy levels. Part of them were attributed to local Ti‒O bond weakening; they should lie close to the bandedges thus causing a tailing of the bandgap absorption and a shift of the flatband potential towards more positive values. Deeper subbandgap states resulting from Ti‒O bond breaking should render the semiconductor strongly sensitive to visible light. However, these lattice defects should also act as recombination centers causing a decrease of the hole diffusion length and therefore a decrease of the photocurrent efficiency.
556
Michael A. Russak and Charles Creter
562
Hyun S. Lim and Jack Winnick
An electrochemical membrane concentration cell was demonstrated as an effective means of removing and concentrating
from a hot gas stream. The device consists of a high temperature molten sulfide electrolyte with porous carbon electrodes. The process‐gas is passed through the cathode chamber, where
is selectively removed. With passage of current, the anion migrates to the anode, where elemental sulfur is evolved. Removal rates and cell overpotentials are reported as functions of current densities, gas flow rates and composition, and temperature.
568
K. C. Pillai and J. O'M. Bockris
The origin of the present work lies in a suggestion by Salamy and Nixon, which was implemented by Tolun and Kitchener, and has become the principal theory of some types of flotation. However, it has never been subject to quantitative verification. The electrochemical kinetics of oxygen reduction and those of the anodic oxidation of potassium ethyl xanthate were examined first individually and then together. The mineral substrates used were iron pyrites and galena. The cathodic Tafel slope on pyrites was 110 mV, and the order of reaction 1.2. On galena, the slope was 120 mV. In anodic reactions, the Tafel slope on pyrites was 95 mV, and the order 0.7. On galena, the slope was 240 mV. Results obtained with
alone and xanthate alone verified the theory. Results obtained when the components were mixed gave agreement only if the excess of the adsorbed xanthate on the oxygen kinetics was taken into account.
579
A. Bélanger, M. Gauthier and D. Fauteux
586
R. Dupon, B. L. Papke, M. A. Ratner and D. F. Shriver
Solid electrolyte complexes of poly(ethylene succinate), PESc, and
were prepared by heating the salt with the molten polymer. The complexes were completely amorphous over the concentration range 1:1 to 3:1 polymer repeat units:metal cation. At salt concentrations above the 1:1 composition, a salt phase was present, and at salt concentrations less than 3:1, free crystalline polymer was observed. Within the 1:1 to 3:1 concentration range, increasing salt concentration was accompanied by decreasing conductivity, and increasing glass transition temperatures. This behavior is discussed in terms of free‐volume theory, with dynamical corrections.
590
Fritz G. Will and Charles D. Iacovangelo
The application of x‐ray radiography in conjunction with high resolution optical densitometry for the quantitative determination of metal deposit profiles parallel and perpendicular to the substrate surface is described. The principles of the technique and the range of its applicability are discussed. The technique is applied to the study of zinc deposition on highly porous carbon foams from circulating aqueous zinc bromide solutions. The effect of substrate pore size on the zinc distribution is explored. Zinc is found to deposit predominantly on the porous substrate/electrolyte and substrate/current collector interfaces. Smaller pore size favors smoother and more uniform deposits throughout the substrate.
595
Yu‐Min Tsou and Fred C. Anson
The formal potentials of several redox couples incorporated in coatings of a perfluoropolycarboxylate on graphite electrodes were measured and compared with the formal potentials of the same couples in homogeneous solution. The differences observed agreed with those calculated from the Nernst equation with the independently measured incorporation coefficients for both halves of the redox couples. The dependences of the shifts in formal potentials on the nature of the incorporating complex ion, the ionic strength, and the temperature were determined and indicated that the incorporation equilibrium is governed by electrostatic and hydrophobic interactions that act in opposite directions. The incorporation of most cations examined was driven by large increases in entropy which overcame the usually unfavorable enthalpy changes.
601
I. V. Kadija
Detailed measurements of interfacial concentration and concentration overpotential of chlorine evolving platinized platinum electrodes were performed in
, at 25°C and 1 atm chlorine or 1 atm nitrogen in the cell. Based on these and electrode polarization measurements, steady‐state activation overpotential curves were obtained. The applied method enabled for the first time in this field, development of true steady‐state activation overpotential curves. Our findings indicated that 30–40 mV/decade slopes typically obtained in nitrogen atmosphere were essentially a sequence of quasi equilibria at the electrode interface. Also, micropolarization data obtained near the open circuit with chlorine atmosphere in the cell were found to be a concentration overpotential phenomenon. The true activation overpotential was found to become a significant part of the electrode polarization only after it exceeded several millivolts in chlorine saturated brine. In nitrogen saturated brine, where the open circuit was undefined, the activation overpotential became significant for polarizations that exceeded two decades of steady‐state low current density polarization. In this case, the activation overpotential was observable as a departure from a 32 mV/decade slope. The obtained activation overpotential curves can be used as a base for developing kinetic parameters, however, a considerably greater emphasis than in the past must be given to the corresponding interfacial conditions.
TECHNICAL NOTES
608
P. T. Moséley and N. J. Bridger
610
F. Bonino, M. Lazzari and B. Scrosati
612
C. Gómez‐Aleixandre, J. M. Albella and J. M. Martínez‐Duart
614
James M. Chen, David R. Damian Jr., Richard M. Stepnowski and Clifton A. Young
617
Anthony F. Sammells and Peter G. P. Ang
619
Joseph T. Hupp and Michael J. Weaver
SOLID-STATE SCIENCE AND TECHNOLOGY TECHNICAL PAPERS
623
Carl E. Bleil and Bernard A. MacIver
Electron diffraction and microscopic analyses of silicon‐implanted polymethyl methacrylate (PMMA) films deposited on glass substrates have been carried out with the aid of differential etching. Results show the films to consist of amorphous and polycrystalline graphite structures incorporating diamond‐like structure in the bulk of the film and silicon carbide crystallites near the film‐glass interface. Particle size is typically less than 50 nm with some crystallites as large as 0.5 μm.
627
Yoshio Sakai, John L. Reynolds and Andrew R. Neureuther
Some aspects of the interaction among wafer topography and the thin film processes of directional dry etching and deposition are presented in experiment and simulation. The anisotropy of dry etching, which has helped make VLSI possible, increases the interdependence of processing steps and opens the possibility of creative uses of topographical effects in fabricating devices. Examples illustrate the importance of these effects and the basic mechanisms involved. Simulation is particularly well suited for systematically examining the trade‐offs among processing steps. Design graphs characterize the effect of anisotropy on line‐width loss and oxide removal in polysilicon gate etching, and on thin film resistance in tapered oxide etching. Guidelines for planarization by isotropic deposition and anisotropic etching are suggested. Comparisons with experiments show that the reported planarizing effect is better than expected.
634
J. Lagowski, L. Jastrzebski, M. T. Duffy, C. Magee and G. W. Cullen
Electronic properties of ion implanted and recrystallized silicon‐on‐sapphire films were studied by surface photovoltage as a function of implantation dose (varied from 1015 to 1016 cm−2). It has been found that all essential characteristics of SOS films undergo a pronounced improvement as a result of high dose
implantation with Si ions followed by a brief annealing (4h at 600°C). The most important improvement has been found with respect to reduction (about two orders of magnitude) in deep‐level concentration situated at the middle of the energy gap, and a significant increase in the minority carrier lifetime.
637
M. L. Naiman, C. T. Kirk, R. J. Aucoin, F. L. Terry, P. W. Wyatt and S. D. Senturia
Thick oxide films (≈220 nm) have been nitrided heavily in ammonia. Dispersion analysis was performed on infrared transmission spectra of oxide, nitrided oxide, and CVD nitride films. The following conclusions may be drawn from the spectra: nitrided oxide is not the same material as CVD silicon nitride; nitridation results in significant loss of Si‐O asymmetric stretch intensity; and nitridation leads to the appearance of a spectral peak for planar triply bonded N‐Si asymmetric stretch analogous to that in trisilylamine. About 43% of the oxygen was replaced by nitrogen.
640
G. Betz, H. Tributsch and S. Fiechter
645
Nicole Herbots, Fernand Van de Wiele, Maurice Lobet and Robert G. Elliman
Interdiffusion between thin films of aluminum (Al) and polycrystalline silicon (poly‐Si) has been studied with the purpose of obtaining a stable interface upon sintering for IC metallization. The solid‐phase crystal regrowth of Si due to this low temperature interdiffusion has also been investigated. Dopant segregation towards the interfaces and the grain boundaries of arsenic‐implanted poly‐Si was used successfully to control the kinetics of Al‐poly‐Si interactions. The correlation between the arsenic depth profiles, the Si‐layer microstructure, and the sintering behavior of the Al‐poly‐Si interface was measured by RBS, (scanning) AES, SEM, TEM, and grazing incidence x‐rays. Quantitative results and discussion of the diffusion mechanisms at work are presented. It is shown that the presence of an arsenic segregation peak on top of the poly‐Si layer stabilizes Al/poly‐Si interface. A concentration of 1019 atom/cm3 appears to be a minimum threshold for sintering at 465°C.
653
Masao Morita, Saburo Imamura, Toshiaki Tamamura, Osamu Kogure and Kei Murase
A new technique for high resolution lithography with a dry‐developed multilayer resist system is demonstrated. The technique involves a direct pattern fabrication by electron beam‐induced vapor‐phase graft‐polymerization. No wet process was included in the pattern fabrication. The use of a double‐layer base film consisting of a thin silicone resin as a top layer and a thick AZ‐1350J film as a bottom layer enabled the transfer of graft‐polymerized polystyrene patterns on the silicone resin to thick resist with submicron‐sized feature.
655
A. Mogro‐Campero and R. P. Love
The reduction of carrier generation lifetime caused by argon implantation into silicon has been studied as a function of argon dose and annealing treatments. The capacitance transient technique was used to deduce that: (i) carrier generation lifetime in the depletion region decreases by four orders of magnitude with doses up to 1014 cm−2, and varies inversely with dose; (ii) the separable contribution to capacitance relaxation due to surface generation and diffusion varies as the square of the dose. The region of low lifetime appears to remain localized within 1 μm from the surface even after annealing for 1h at 1200°C. Partial recovery of generation lifetime occurs after annealing for 1h at 1100° or 1200°C. Complete recovery was observed only after several hours at 1200°C, and slow cooling (2°C min−1). The resistance to high temperature treatment implies that regions of low lifetime can be incorporated with three‐dimensional control into device structures.
660
G. Hsu, R. Hogle, N. Rohatgi and A. Morrison
Silicon deposition on silicon seed particles by silane pyrolysis in a fluidized bed reactor is being investigated as a low cost, high throughput method to produce high purity polysilicon for solar cell applications. Studies of fines, particles 0.1–10μ diam, initiated from homogeneous decomposition in the reactor were conducted using 2 and 6 in. diam fluidized beds. The studies show functional dependences of fines elutriation on operating parameters such as silane feed concentration, temperature, gas velocity, and bubble size. The observation that the fines elutriation is generally below 10% of the silicon‐in‐silane feed is explained using a concept of scavenging by large particles in an environment of less free space for homogeneous nucleation. Preliminary results suggest that, with proper conditions and distributor design, high silane concentration (
in
) feed may be used for silicon production in fluidized bed reactors.
663
M. Hirayama, T. Matsukawa, H. Arima, Y. Ohno, N. Tsubouchi and H. Nakata
Silicon nitride films were directly formed on silicon by plasma anodic nitridation within nitrogen and hydrogen. The nitridation pressure ranged from 0.5 to 2.0 torr, at temperatures from 700° to 900°C. The growth rate of silicon nitride increased with an increase of the dc bias voltage to the silicon wafers. The refractive index of the films was measured to be about 2.00–2.30 by ellipsometry. Film composition was analyzed with Auger electron spectroscopy. Dielectric breakdown strength of the silicon nitride films was about 6.0 MV/cm after oxygen heat‐treatment.
TECHNICAL NOTES
667
B. L. Sopori
672
L. Liou, W. G. Spitzer and S. Prussin
675
G. Harbeke, L. Krausbauer, E. F. Steigmeier, A. E. Widmer, H. F. Kappert and G. Neugebauer
Undoped LPCVD silicon films have been deposited at five temperatures between 560° and 620°C. The films were characterized as grown and after thermal annealing at 900°, 950°, and 1000°C. We used x‐ray diffraction, TEM, SEM, Raman and elastic light scattering, optical absorption and reflection, and other techniques in order to obtain information on the grain size, structure, structural perfection, and surface roughness. We found that polysilicon films of good structural perfection, low strain, and small surface roughness are obtained when the films are deposited in the amorphous phase and subsequently crystallized at 900°–1000°C. Such films are superior in all investigated material aspects to films grown in the crystalline phase.
ACCELERATED BRIEF COMMUNICATIONS
683
B. Y. Liu and Y. C. Cheng
A novel Dual TCE (two step trichloroethylene) oxidation process has been developed to grow thin and highly reliable gate oxides for very large scale MOS application. The main features consist of an initial low temperature oxidation providing a low‐defect‐density oxide structure and a subsequent high temperature oxidation providing a good interface with passivation ability against mobile ions. Combinations of various percentages of TCE and different oxidation conditions are examined. It is found that thin oxides obtained by Dual TCE process have high dielectric break‐down fields and good oxide‐silicon interface, similar to those obtained by two step
oxidation, but without their associated disadvantages.
687
R. A. Bull, F. ‐R. Fan and A. J. Bard