Batteries, Fuel Cells, and Energy Conversion
A221
Y. Wu and A. Manthiram
A225
Xiaoping Wang, Romesh Kumar and Deborah J. Myers
A228
Sung-Jin Ahn, Jong-Ho Lee, Joosun Kim and Jooho Moon
A232
Li-Yin Hsiao, Ting Fang and Jenq-Gong Duh
Tin-based alloy/carbonaceous composite materials are attractions for Li-ion rechargeable batteries because of their high capacity. A novel Ni–Sn–P mesocarbon microbead (MCMB) composite material for lithium-ion batteries was prepared by an electroless plating method. On the basis of X-ray color mapping analysis by electron probe microanalyzer, the nanosize Ni–Sn–P was precipitated not only on the surface but in the interior of MCMB powders. The Ni–Sn–P/MCMB composite anode exhibited large capacity (
in the tenth cycle) and the coulombic efficiency of the Ni–Sn–P/MCMB anode is as high as 98% even after the twenty-fifth cycle. In addition, the Ni–Sn–P/MCMB composite anode showed a significant improvement in electrochemical performance. Therefore, the Ni–Sn–P/MCMB provides a new type of anode material for lithium-ion batteries with an enhanced capacity.
A237
Y. Huang, J. M. Vohs and R. J. Gorte
A241
J. Choi, E. Alvarez, T. A. Arunkumar and A. Manthiram
A245
W. Choi and A. Manthiram
A249
Guangchun Li and Peter G. Pickup
Anode overpotentials in a commercial fuel cell have been measured using dynamic hydrogen reference electrodes (DHE) at the top and bottom of the cell. During operation of the cell with dry
and
, which causes dehydration of the top of the anode, the top DHE consistently yielded higher anode overpotentials than the bottom DHE. Poisoning of the top part of the anode with CO greatly enhanced this disparity. Together with the observed time dependences, these results clearly indicate that overpotentials measured by using reference electrodes outside the active area of a fuel cell are local values.
A252
Ranga S. Jayashree, Daniela Egas, Jacob S. Spendelow, Dilip Natarajan, Larry J. Markoski and Paul J.A. Kenis
We report the performance of an air-breathing laminar flow-based fuel cell (LFFC) operated in alkaline and acidic media. These direct methanol fuel cells exhibit open-circuit potentials of 0.93 and
in acidic and alkaline media, respectively, demonstrating the absence of methanol crossover in both media. The LFFCs perform better in alkaline media under identical reaction conditions due to improved reaction kinetics at high pH. Further electrochemical investigation of these differences in reaction kinetics at the anode and cathode is also reported.
A257
Yosef Gofer, Orit Chusid, Haim Gizbar, Yulia Viestfrid, Hugo E. Gottlieb, Vered Marks and Doron Aurbach
Electrolyte solutions of magnesium organo-halo-aluminates in ethers are suitable for rechargeable magnesium batteries as they enable highly reversible electrodeposition for magnesium while they possess a wide electrochemical window
. Adding LiCl or tetrabutylammonium chloride to these solutions considerably improves their ionic conductivity, the kinetics of the Mg deposition-dissolution processes, and the intercalation behavior of
Chevrel cathodes. The dissolution of both salts in the electrolytic solutions involves acid-base reactions with complex species. Multinuclei nuclear magnetic resonance and Raman spectroscopy were used in conjunction with electrochemical techniques to study these systems. The nature of these reactions, their products, and the way they influence the various properties of these solutions, are discussed herein.
Corrosion, Passivation, and Anodic Films
B25
Ying Liu and Meilin Liu
Nanostructured composite powder, consisting of 
,
NiO, and 
(GDC), was prepared using a combustion chemical vapor deposition process from a single solution containing all precursors. Bilayer solid oxide fuel cells (SOFC) anodes of different porosity were fabricated by copressing of NiO-GDC powder and
composite powder. Porosity variation in the anodes was achieved by the removal of the
-phase during firing and subsequent cell testing. Anode-supported SOFC single cells were constructed and tested for electrochemical performance. Interfacial polarization resistances of a cell with the bilayer anode were 1.20, 0.49, 0.22, and
at 500, 550, 600, and
, respectively, demonstrating peak power densities of 171, 301, 441, and
, respectively.
B28
Hongyi Li, Xinde Bai, Yunhan Ling, Juan Li, Dailan Zhang and Jinshu Wang
Titania oxide nanotubes were successfully grown from a clean titanium plate via the direct anodic oxidation method. The as-prepared nanotubes were amorphous and were crystallized at
, which was identified by X-ray diffraction (XRD) patterns. Their microstructures and morphologies were investigated by field emission scanning electron microscopy (FESEM). The photoelectrochemical properties of the annealed nanotubes thin films coupled with 304 stainless steel (304 SS) were studied on IM6e instrument. A significant photoelectrochemical response effect was observed. The open-circuit potential of the titania nanotubes films coupled with 304 SS shifts negatively in the presence of simulated solar light (from a metal halogen lamp) and the polarization curves reveal that titania nanotube thin films have photocathodic protection properties of 304 SS.
B32
Shunsuke Yagi, Kuniaki Murase, Tetsuji Hirato and Yasuhiro Awakura
Electrochemical/Chemical Deposition and Etching
C81
R. W. Tjerkstra
C85
Ying-Chao Sung, Chia-Han Lai, Su-Jien Lin and Shou-Yi Chang
The atomic-scale crystallography of early-stage nucleation of sensitization-activated palladium (Pd) catalysts and electrolessly plated copper (Cu) films has been investigated. Small Pd nanocrystallites of
were uniformly distributed as a single layer. Neighboring Pd nanocrystallites exhibited similar crystallography irrelevant to the random orientations of polycrystalline TaN substrate. Subsequently deposited Cu nanocrystallites of only
with small-angle boundaries nucleated on the Pd nanocrystallites with an orientation relationship of Cu [111] parallel to Pd [111]. In comparison, displacement-activated Pd preferentially nucleated on TaN, and Cu followed the orientation of Pd grains with a relationship of Cu [111] parallel to Pd [200].
C88
Diwakar Iyer, Dinakar Palaparti, Elizabeth J. Podlaha, M. Cindy Henk and Michael C. Murphy
Electrochemical Synthesis and Engineering
D13
I. Lombardi, L. Magagnin, P. L. Cavallotti, C. Carraro and R. Maboudian
A process was developed that uses a porous anodic alumina (PAA) mask as a template to electrochemically grow supported metal nanodots and nanowires without the need of aluminum evaporation. A PAA film was fabricated from a high purity Al foil and transferred onto a copper-coated silicon wafer. Nickel was plated with direct current inside the pores of the PAA and silicon supported arrays of Ni nanodots and nanowires were obtained. The transferred porous anodic alumina template process is assessed in terms of feasibility with metallic substrates other than copper.
Dielectric Science and Materials
F23
I. Valov, C. Korte, R. A. De Souza, M. Martin and J. Janek
F27
M.-H. Cho, K. B. Chung, Y. K. Kim, D. C. Kim, J.-H. Heo, B. Y. Koo, Y. K. Shin, U. I. Chung, J. T. Moon and D.-H. Ko
The depth profile in nitrided
films using
remote radio frequency plasma was investigated. N was incorporated into the film at levels of up to 27 atom %, largely concentrated at the film surface, and not the film interface. The depth profiling data showed that the depth of incorporated N is dependant on film thickness, i.e., N is incorporated to a depth of about
in a
thick film, while the depth is significantly less to about
in the case of a
thick film. Moreover, under the same nitridation condition, more N content is concentrated nearer to the surface of a
thick oxide film than that of
thick film.
, generated in the molecule during the nitrogen process is almost completely concentrated at the film interface. After an additional annealing treatment, the molecular
diffuses out extensively and N, which is chemically bonded to
, is changed into a more stable state with different second-nearest neighbors, accompanied by reoxidation at the film interface of an ultrathin film.
F31
Ru-Yuan Yang, Min-Hang Weng, Yung-Shou Ho, Yan-Kuin Su and Yu-Ming Yeh
F34
Pan Kwi Park, Jae-Sung Roh, Byung Ho Choi and Sang-Won Kang
The interfacial oxide layers, generated on Si substrates during the initial stage of
atomic layer deposition (ALD), have been investigated depending on the oxygen reactants, oxygen plasma and water. In the plasma-enhanced ALD (PEALD) using oxygen plasma, a
-thick interfacial layer, which was intermixed with Hf–Si–O and
having a dielectric constant
of 6.5, was formed, while water made a
-thick interfacial layer composed mainly of
. Additionally, by utilizing oxygen plasma, the
of the
film itself was increased up to 22.2 resulting in a higher effective
, and a much lower leakage current density was also obtained.
F38
Yi-Hsien Lee, Chia-Ching Lee, Zeng-Xun Liu, Chun-Sheng Liang and Jenn-Ming Wu
Semiconductor Devices, Materials, and Processing
G155
Chih-Yang Chang, Tian-Wey Lan, Gou-Chung Chi, Li-Chyong Chen, Kuei-Hsien Chen, Jau-Juin Chen, Soohwan Jang, F. Ren and S. J. Pearton
G158
S. Balakumar, M. M. Roy, B. Ramamurthy, C. H. Tung, Gao Fei, S. Tripathy, Chi Dongzhi, R. Kumar, N. Balasubramanian and D. L. Kwong
Germanium (Ge) metal-oxide-semiconductor-field-effect transistors (MOSFETs) have higher carrier mobilities than Si. We have studied the growth of high quality single-crystal germanium on insulator (GOI) using rapid liquid-phase epitaxial growth and defect-necking techniques. Stable single-crystal Ge growth was seen at a temperature of
, below the melting point of Ge. At and above the Ge melting temperature, we found Ge segregating into balls. Defect-free crystals were grown from the semisolid state of Ge. The defect-necking technique was improved with an underlying insulator undercut to minimize dislocation or stacking faults. Up to
long crystal-on-insulators were grown. Strain analysis of grown Ge was studied using Raman spectroscopy, and grown films were found to have tensile strain.
G161
S. B. Herner
G164
J. S. Wright, R. Khanna, D. P. Norton, S. J. Pearton, F. Ren and I. I. Kravchenko
G167
Jie Sun, Ruoyuan Li, Chang Zhao, Like Yu, Xiaoling Ye, Bo Xu, Yonghai Chen and Zhanguo Wang
Molecular beam epitaxy is employed to manufacture self-assembled InAs/AlAs quantum-dot resonant tunneling diodes. The resonant tunneling current is superimposed on the thermal current, and together they make up the total electron transport in devices. Steps in current-voltage characteristics and peaks in capacitance-voltage characteristics are explained as electron resonant tunneling via quantum dots at 77 or
, and thus resonant tunneling is observed at room temperature in III-V quantum-dot materials. Hysteresis loops in the curves are attributed to hot electron injection/emission process of quantum dots, which indicates the concomitant charging/discharging effect.
G171
S. C. Hsu and C. Y. Liu
G174
Y.-J. Chang, P. H. Mugdur, S.-Y. Han, A. A. Morrone, S. O. Ryu, T.-J. Lee and C.-H. Chang
In this work, we developed a continuous flow microreactor that is capable of overcoming the drawbacks associated with chemical bath deposition. Uniform, smooth, and highly oriented nanocrystalline CdS semiconductor thin films were successfully deposited on oxidized silicon substrates at low temperature
using this microreactor. Functional thin-film transistors with an effective mobility of
were fabricated from the as-deposited films without any postannealing process. This process is a potentially low-cost avenue for the fabrication of thin-film electronics on flexible polymeric substrates.
G178
Jae-Hoon Lee, Joong-Hyun Park, Hee-Sun Shin and Min-Koo Han
A gate overlapped lightly doped drain (GOLDD) poly-Si thin film transistor (TFT) employing the 45° tilt implant for source and drain (S/D) regions, is proposed. In order to activate both
S/D and
lightly doped drain (LDD) regions, and to eliminate junction defects, oblique-incident excimer laser annealing activation (OI-ELA) was performed. At certain conditions, such as when
,
, the proposed poly-Si TFT with
exhibited a lower anomalous leakage current of
, than conventional TFTs, with an anomalous leakage current of
. In addition, the proposed device held 89% of maximum transconductance against hot-carrier stress, compared to the conventional one, which holds 46%.
G181
C. H. Ho, Y. J. Chen, Y. H. Liang, J. C. Yeh and T. C. Tsai
G184
Jinhua Chen, Masaharu Asano, Yasunari Maekawa, Takahiro Sakamura, Hitoshi Kubota and Masaru Yoshida
UV radiation-induced photografting of styrene into poly(tetrafluoroethylene-co-ethylene) (ETFE) films for the preparation of fuel cell membranes was carried out. The proton conductivity in the thickness direction of membranes prepared by the vapor- and liquid-phase photografting can reach as high as 0.065 and
, respectively. The higher conductivity in the liquid-phase grafting is close to the homogeneity of graft chain distribution in the membrane.
G187
Haimei Liu, Ryuhei Nakamura and Yoshihiro Nakato
Sensors and Displays: Principles, Materials, and Processing
H31
A. Dubbe and R. Moos
General Topics
J17
Laxmikant Saraf, D. E. McCready, V. Shutthanandan, C. M. Wang, M. H. Engelhard and S. Thevuthasan
Miscellaneous
L3
D. Josell, C. Witt and T. P. Moffat
L4
D. Josell, J. E. Bonevich, T. P. Moffat, T. Aaltonen, M. Ritala and M. Leskelä
L5
Takuma Katase, Ryoichi Kurosaki, Kuniaki Murase, Tetsuji Hirato and Yasuhiro Awakura