The Electrochemical Society was founded in 1902 to advance the theory and practice at the forefront of electrochemical and solid state science and technology, and allied subjects.
Find out more about ECS publications
Visit the ECS homepage
Number 5, January 2004
Previous issueNext issue
Open all abstracts, in this issue
M. N. Obrovac and Leif Christensen
The structural changes in silicon electrochemically lithiated and delithiated at room temperature were studied by X-ray powder diffraction. Crystalline silicon becomes amorphous during lithium insertion, confirming previous studies. Highly lithiated amorphous silicon suddenly crystallizes at 50 mV to form a new lithium-silicon phase, identified as Li15Si4. This phase is the fully lithiated phase for silicon at room temperature, not Li21Si5 as is widely believed. Delithiation of the Li15Si4 phase results in the formation of amorphous silicon. Cycling silicon anodes above 50 mV avoids the formation of crystallized phases completely and results in better cycling performance. © 2004 The Electrochemical Society. All rights reserved.
Patrick C. Howlett, Douglas R. MacFarlane and Anthony F. Hollenkamp
A room-temperature ionic liquid (RTIL) solvent, N-methyl, N-alkyl pyrrolidinium bis(trifluoromethanesulfonyl)amide (P1X(Tf)2N), has been investigated for use in a lithium metal battery. An average cycling efficiency of >99% is achieved at 1.0 mA cm−2(Idep=Idiss) on platinum. At deposition rates up to 1.75 mA cm−2 optical micrographs indicate that the deposit is uniform and nondendritic. Above 1.75 mA cm−2, the deposit becomes dendritic and efficiency decays. High cycling efficiency (>99%) can also be obtained on copper, but at relatively low current density (0.1 mA cm−2). The deposition/cycling history also influences the cycling behavior of the deposit. © 2004 The Electrochemical Society. All rights reserved.
X. P. Gao, Z. W. Lu, Y. Wang, F. Wu, D. Y. Song and P. W. Shen
La2Mg17-based nanocrystalline alloys were prepared by ballmilling La2Mg17 alloy with Ni powders. Electrochemical charging and discharging of the ballmilled La2Mg17-based nanocrystalline alloy succeeded due to the formation of highly dispersed metallic Ni particles through the nanocrystalline alloy matrix. The first discharge capacity of the La2Mg17 alloys ballmilled with Ni powders in a weight ratio of 1:2 was near 990 mAh/g, corresponding to a hydrogen storage capacity of 3.69 wt %. Inlaid metallic Ni at the surface layer of the nanocrystalline alloy matrix served as electrocatalytic reaction sites and hydrogen adsorption sites to accelerate the electrochemical charging and discharging process. © 2004 The Electrochemical Society. All rights reserved.
Zhonghe Bi, Baolian Yi, Zhenwei Wang, Yonglai Dong, Hejin Wu, Yunchuan She and Mojie Cheng
An anode-supported solid oxide fuel cell (SOFC) with lanthanum-doped ceria (LDC) and strontium and magnesium doped lanthanum gallate (LSGM) bilayer electrolytes was fabricated and tested. The bilayer electrolyte thin film, consisting of a 25 μm thick LDC layer and a 75 μm thick LSGM layer, was prepared by a simple dry-pressing process. The two electrolyte layers were sintered together well, and no crack and peel-off at the interface were observed. An open-circuit potential of 1.02 V and a maximum power density of over 1.1W/cm2 was achieved with H2 as fuel and air as oxidant at 800°C. The results show that the reactions between LSGM and anode materials were restrained by the LDC electrolyte layer, whereas the electronic conductivity of ceria-based electrolyte was blocked by the LSGM electrolyte layer. © 2004 The Electrochemical Society. All rights reserved.
Daisuke Hirabayashi, Atsuko Hashimoto, Takashi Hibino, Ushio Harada and Mitsuru Sano
Doped Bi-based oxides were investigated as potential anode materials for direct hydrocarbon solid oxide fuel cells (SOFCs) at intermediate temperatures. (Bi2O3)0.85(Ta2O5)0.15 met this criterion most successfully. A fraction of Bi2O3 in this material was reduced to BiO and Bi metal under fuel conditions, which yielded high conductivities (<1Scm−1) based on oxide ions and electrons above 500°C. Carbon deposition was successfully prevented when butane was used as the fuel below 800°C. The catalytic activities for hydrocarbon oxidation were high enough to promote the complete oxidation of butane during cell operation. These abilities provided an enhanced anode performance with increasing temperature from 600 to 750°C, and the resulting polarization resistance reached 1.4 Ω cm2 at 750°C. © 2004 The Electrochemical Society. All rights reserved.
Steven McIntosh, Stuart B. Adler, John M. Vohs and Raymond J. Gorte
Identical strontium-doped LaMnO3 and yttria-doped zirconia (LSM-YSZ) composite electrodes were characterized in three separate cell configurations, in air at 973 K using impedance spectroscopy. These configurations included a single-cell solid oxide fuel cell (SOFC), a symmetric cell (cathode/YSZ/cathode), and a thick pellet half-cell. Large discrepancies were observed in the measurements, with the electrode showing a current-independent area-specific resistance (ASR) of ∼0.2 Ω cm2 as an SOFC cathode, while nearly identical electrodes in the other two configurations exhibited nonlinear behavior, with ASR as large as 12 Ω cm2. The discrepancies are partly explained by electrode polarization effects. This has important implications for cathode characterization in SOFC. © 2004 The Electrochemical Society. All rights reserved.
I. Lombardi, M. Bestetti, C. Mazzocchia, P. L. Cavallotti and U. Ducati
The electrochemical behavior and the reversible hydrogen storage capacity of multiwalled carbon nanotubes (MWNTs) have been investigated both in alkaline (6 M KOH) and acid (0.3 M H2SO4) electrolytic solutions by cyclic voltammetry and constant current charge/discharge measurements. Different purification treatments were performed on as-prepared MWNTs to improve hydrogen uptake. About 0.1 wt % of hydrogen was reversibly stored in MWNTs after nitric acid treatment. Vacuum annealing (950°C, 1 h) of MWNTs lowered the electrochemical hydrogen uptake. Finally, electrochemical oxidation of MWNTs at high potentials allowed an increase in hydrogen charge capacity to 0.3 wt %. © 2004 The Electrochemical Society. All rights reserved.
M. Hayashi, H. Arai, H. Ohtsuka and Y. Sakurai
The electrochemical insertion/extraction of calcium ions into/from crystalline vanadium oxide (cV2O5) was investigated by galvanostatic measurements. Electrochemical cells using cV2O5 as a cathode active material provided a discharge capacity of more than 450 mAh g−1 at a current density of 50 μAcm−2. However the discharge capacity decreased greatly as the current density increased. This behavior seemed to reflect that calcium ions do not diffuse easily in the oxide lattice. The structural changes in cV2O5 after discharging and charging were analyzed by X-ray diffraction (XRD). After discharging, a new phase caused by the ion-insertion reaction was observed in the XRD pattern that coexisted with the pristine cV2O5 phase. © 2004 The Electrochemical Society. All rights reserved.
Geraint Williams and H. Neil McMurray
Benzotriazolate, ethyl xanthate, and oxalate anion-exchanged hydrotalcite (HT) pigments are evaluated with respect to their ability to inhibit filiform corrosion (FFC) on organic coated AA2024-T3 aluminum alloy. Following FFC initiation by application of aqueous HCl to a penetrative coating defect, the time-dependent extent of coating delamination was determined both optically and by repeated in situ measurements performed using a scanning Kelvin probe (SKP). Inhibitor efficiency is shown to increase in the order ethyl xanthate≪oxalate<benzotriazolate. Benzotriazolate is also shown to interact specifically with the alloy surface, depressing Volta potential values by up to 0.4 V. © 2004 The Electrochemical Society. All rights reserved.
Tohru Hara and Ken Namiki
Optimizing the composition of a TaSiN barrier layer is presented. The stress in a copper seed layer decreases markedly with the increase of Si composition in the barrier. A resistivity of 2.8 μΩ-cm is obtained when a TaN barrier layer (Si composition: 0) is used. This resistivity decreases with increasing composition of Si in the TaSiN barrier layer and reaches a minimum of 2.3 μΩ-cm in an as-deposited 300 nm thick copper layer on a TaSiN barrier containing 0.06 Si. Resistivity of 1.92 and 1.82 μΩ-cm can be obtained in 300 and 500 nm thick copper layers, respectively, after annealing. © 2004 The Electrochemical Society. All rights reserved.
M. T. Wu, I. C. Leu, J. H. Yen and M. H. Hon
Recently, many nanostructures have been prepared successfully through electrodeposition of materials into anodic porous alumina coated with a conductive layer on the bottom. Here, the fabrication of Ni nanostructures using anodic porous alumina on Si as a template without a conductive interlayer is investigated. Morphologies of Ni nanostructures were dominated by the applied voltages and an excellent replication capability for this method was revealed. The novel electrodeposition behavior in this study is quite different from the “bottom-up” electrodeposition in conventional template-mediated growth of materials. © 2004 The Electrochemical Society. All rights reserved.
Young Soo Song, Sang Jin Park, Tae Wan Kim and Chee Won Chung
The wet chemical cleaning of a magnetic tunnel junction (MTJ) stack after dry etching was carried out to eliminate the redeposited materials on the sidewall of the MTJ and to examine the effect on the properties of the MTJ. Wet cleaning may result in the degradation of electrical properties of a MTJ. The resistance (R)-magnetic field (H) curve after cleaning showed that CoFe pinned layer was switched at low magnetic field. It was proved from transmission electron microscopy that CoFe and IrMn layers were attacked and the interface between the two layers was damaged due to the reaction with cleaning solutions. © 2004 The Electrochemical Society. All rights reserved.
Zuocheng Wang, Hongqi Li, Hasan Shodiev and Ian Ivar Suni
Continuous Cu films are deposited on Ta by a two-step process; galvanic displacement of Ta by Cu from ammonium fluoride solutions and subsequent electroless Cu deposition from a formaldehyde-containing bath. The conditions necessary for good adhesion are discussed. The extent of oxide film removal in the HF pretreatment solution is studied by electrochemical impedance spectroscopy. The charge-transfer resistance of about 57 Ωcm2 is several orders of magnitude lower than that measured for the Ta native oxide. These results are consistent with the removal of the Ta2O5 portion of the native oxide. © 2004 The Electrochemical Society. All rights reserved.
Hironori Nakajima, Toshiyuki Nohira and Yasuhiko Ito
Infrared spectroscopy of molten LiCl-KCl-LiH at 673 K provided absorption band in the wavenumber region of 14001500 cm−1 for several H− ion concentrations. This absorption band is ascribed to the vibration of Li+H− ion pair in the melt. The absorption band ascribed to the vibration of K+H− ion pair was not observed in the melt. The existence of the Li-H interaction shows a strong attractive force between H− ion and Li+ ion in the melt. © 2004 The Electrochemical Society. All rights reserved.
W. C. Shin, S. O. Ryu, I. K. You, S. M. Yoon, S. M. Cho, N. Y. Lee, K. D. Kim, B. G. Yu, W. J. Lee, K. J. Choi et al
60 nm thick SrBi2Ta2O9 (SBT) thin films were fabricated using plasma-enhanced atomic layer deposition (ALD) with an alternating supply of single cocktail source and oxygen plasma. The linear relationship between the number of cycles and film thickness and a constant deposition rate with source pulse time suggests that a self-limiting process that has distinct characteristics of ALD was achieved. The 60 nm thick SrBi2Ta2O9 films that were annealed at 750°C completely crystallized to the layer-structured perovskite phase. The SBT capacitors showed excellent ferroelectric switching properties. Low voltage switching below 1.5 V was achieved successfully in the 60 nm SBT capacitor. © 2004 The Electrochemical Society. All rights reserved.
Jaehyun Kim and Kijung Yong
Zirconium silicate [(ZrO2)X(SiO2)1−X] films were deposited by using a combination of precursors: tetrakis(diethylamido)zirconium [Zr(NEt2)4] and tetranbutyl orthosilicate [Si(OnBu)4]. An atomically flat interface of silicate/silicon was observed with no interfacial silicon oxide layers and impurity concentrations were less than 0.1 atom % (below detection limits). Zirconium silicate films with ∼20%ZrO2 were amorphous up to 800°C and, above 900°C, phase separation of the films occurred into crystal ZrO2 and amorphous phases. Dielectric constant (k) of the Zr-silicate films was about 7.3. Hysteresis in capacitance-voltage (CV) measurements was less than 0.02 V. The leakage current density was 1.63×10−4A/cm2 at a bias of 1.0 V. © 2004 The Electrochemical Society.
Yen-Po Lin and Jenn-Gwo Hwu
Low-pressure chemical vapor deposition (LPCVD) Si3N4 quality presents a dramatic improvement after oxidation. Both liquid-phase anodic oxidation and rapid thermal oxidation were studied in this work. After oxidation, “SiO2”like layers grown on the surface, and oxygen incorporated into the Si3N4 layer were observed. The nonstoichiometric bonding, i.e., Si2=N, Si dangling bonds, and crystalline Si were oxidized into Si2=N‒O or SiO2, and the stoichiometric Si3≡N bonding maintained a higher-k property. In addition, more oxygen replacement of the imperfect Si-N bonds after anodic oxidation contributed to better improvement in suppressing gate leakage current. © 2004 The Electrochemical Society. All rights reserved.
M. N. Chang, W. W. Wan, C. Y. Chen, J. H. Lai, J. H. Liang and F. M. Pan
We have successfully employed scanning capacitance microscopy (SCM) operated under low photoperturbation to investigate electrical junction profiles in low-energy BF2+-implanted silicon wafers treated by various annealing sequences. Differential capacitance images reveal that rapid thermal annealing (RTA) followed by furnace annealing (FA) treatments (RTA+FA) can result in a narrower junction width and a shallower electrical junction depth than FA followed by RTA treatments (FA+RTA). Experimental results also indicate that the wider junction of the FA+RTA treated sample is due to the shallower concentrated distribution of electrically activated boron atoms upon annealing. Subtle correlations between electrical junctions and annealing conditions are discussed. © 2004 The Electrochemical Society. All rights reserved.
A. Cabot, J. Arbiol, E. Rossinyol, J. R. Morante, Fanglin Chen and Meilin Liu
Tin oxide nanostructures with controlled narrow particle size distribution were synthesized inside silica mesoporous templates. In this way, particle growth was blocked by physically corseting the tin compound inside the silica frameworks, the pore diameter of which determines the final tin oxide crystallite size distribution. Template structures were subsequently eliminated by chemical methods to collect the unsupported semiconductor nanoparticles. Thus obtained tin oxide nanopowders, with particle sizes in the range between 6 and 10 nm, were structurally, chemically, and electrically characterized. The results are compared with those obtained from the characterization of larger crystallite materials. © 2004 The Electrochemical Society. All rights reserved.
Junji Sasano, Patrik Schmuki, Tetsuo Sakka and Yukio H. Ogata
Maskless Cu patterning on porous silicon (PS) assisted by a focused laser beam is demonstrated. Cu was selectively electroplated only at the illuminated part of PS by utilizing the rectifying properties of the Schottky barrier formed at a p-type semiconductor/solution interface. Applying this principle, Cu deposition was achieved in the presence of Cl− ions necessary for inhibition of the immersion plating reaction. © 2004 The Electrochemical Society. All rights reserved.
Soo Young Kim and Jong-Lam Lee
We report low-resistant and high reflective ohmic contact on p-type GaN using a promising Ni/Au/indium-tin oxide (ITO)/Ag contact scheme. Specific contact resistivity as low as 3.2×10−5Ω cm2 was obtained from Ni (20 Å)/Au (30 Å)/ITO (600Å)/Ag(1200Å) contact annealed at 500°C under an oxidizing ambient. The relative reflectance of contact was evaluated to be 78.8%, which is 14.6% higher than the Ni/Au contact. The ITO layer acted as a diffusion barrier for both indiffusion of Ag and out-diffusion of Au, providing a low resistant and highly reflective ohmic contact on p-type GaN. © 2004 The Electrochemical Society. All rights reserved.
S. W. Bedell, D. K. Sadana, K. Fogel, H. Chen and A. Domenicucci
A chemical defect etching technique is described that permits accurate determination of defect density in thin Si/SiGe bilayer films. The etching technique is capable of distinguishing between isolated defect pits, such as threading defects, and planar defects in the top Si layer within the resolution of optical microscopy. A strained Si layer grown on a silicon-germanium-on-insulator substrate with a 40 atom % Ge content was analyzed using the new etching technique and the measured defect density compared well with plan-view transmission electron microscopy (PV-TEM) and cross-sectional TEM (X-TEM) results. X-TEM revealed that the planar defects observed in the defect etching images correspond to microtwin defects. © 2004 The Electrochemical Society. All rights reserved.
S. B. Herner, M. Konevecki, U. Raghuram, S. Sivaram and M. H. Clark
The deposition of p+ polycrystalline silicon films on SiO2 substrates by SiH4/BCl3 gases has been characterized. Films were deposited at temperatures as low as 460°C with an as-deposited resistivity of 3560±130 μΩ cm with good step coverage in oxide trenches. The extracted activation energy for silicon deposition was 0.6 eV for temperatures between 490 and 580°C and boron concentration of 2.0±0.4×1021/cm3, compared with 0.2 eV for p+ silicon deposition by SiH4/B2H6 for similar conditions. Silicon films deposited by SiH4/BCl3 are polycrystalline with low resistivities as-deposited at 460°C, whereas films deposited by SiH4/B2H6 are amorphous at deposition temperatures <520°C. © 2004 The Electrochemical Society. All rights reserved.
Joung Kyu Park, Kyoung Jae Choi, Chang Hae Kim, Hee Dong Park and Se Young Choi
We have synthesized a Eu2+-activated Sr2SiO4 yellow phosphor and investigated an attempt to develop white light-emitting diodes (LEDs) by combining the phosphor with a GaN blue LED chip. Two distinct emission bands from the GaN-based LED and the Sr2SiO4:Eu phosphor are clearly observed at 400 nm and at around 550 nm, respectively. These two emission bands combine to give a spectrum that appears white to the naked eye. Also, we investigated the compositional dependence of the luminescence properties of Eu2+ ions based on the different Mg2+ contents. © 2004 The Electrochemical Society. All rights reserved.
Yasuo Shimomura and Naoto Kijima
The mechanism of formation of Y4Al2O9 during spray pyrolysis of Y2O3:Eu3+ at 1800°C was studied by calculating the equilibrium composition in the furnace using a thermodynamic database. At high temperature in the presence of water, Y4Al2O9 was generated from gaseous aluminum compounds volatilized from the alumina reactor tube and yttrium compounds, which were the raw materials of the phosphor. The calculation also indicated that reduction of the amount of water in the furnace would decrease the amounts of volatilized aluminum compounds. Decreasing the amount of water using a diffusion drier controlled the generation of impurities. © 2004 The Electrochemical Society.