Batteries, Fuel Cells, and Energy Conversion
A123
Mao-Sung Wu and Pin-Chi Julia Chiang
Nanostructured manganese oxide electrodes are electrochemically synthesized by cyclic voltammetric and potentiostatic methods. Electrode structure greatly influences the electrochemical performances of the capacitors. An electrode composed of evenly distributed 30 nm nanorods fabricated by cyclic voltammetry has a higher specific surface area, which possesses a higher capacitance of 243.2 F/g. A specific capacitance of potentiostatic deposited electrode is only 210.4 F/g due to the lower specific area. Pore distribution of a nanostructured electrode was analyzed by ac impedance technique. The potentiostatic deposited electrode has a higher percentage of large pores than the cyclic voltammetric deposited electrode, and therefore is capable of delivering high power. © 2004 The Electrochemical Society. All rights reserved.
A127
Min-Kyu Song, Young-Taek Kim, Ji-Seok Hwang, Heung Yong Ha and Hee-Woo Rhee
Nafion membrane was cast from 5 wt % Nafion/dimethly acetamide/2-propanol solution containing a hydrophobic plasticizer, and the phase-separated low molecular weight component was leached out from the Nafion matrix by solvent extraction using diethyl ether and methanol. The resultant porous Nafion membrane was doped in situ with zirconium hydrogen phosphate (ZHP) by zirconium chloride and phosphoric acid treatment. The maximum loading of ZHP nanoparticles increased to 40 wt % because of additional precipitation in the pore structure. Field-emission scanning electron micrographs showed that the pores were completely filled with in situ doped ZHP particles. Fourier transform infrared study confirmed that more ZHP fillers improved water retention and proton conductivity of the composite ionomer membrane at high-temperature regions above 100°C. As a result, the power density of Nafion/ZHP membranes was much higher than that of an as-received Nafion 115 membrane at elevated temperature. © 2004 The Electrochemical Society. All rights reserved.
A131
Yong-Nian Xu, Sung-Yoon Chung, Jason T. Bloking, Yet-Ming Chiang and W. Y. Ching
A135
Hitoshi Nakajima and Itaru Honma
A type of anode electrocatalyst for methanol oxidation, which was important for their application to direct methanol fuel cells, was synthesized by the reaction of tetrabutylammonium α-undecatungstosilicate and hydrogen hexachloroplatinum in acetone, followed by washing with water. This polyoxometalate coordinated platinum stoichiometrically in the lacunary site of Keggin-type polyanion. This polyoxometalate showed high methanol oxidation current despite low Pt ratio and oxide-base catalyst. This kind of electrocatalyst has the advantages of low Pt utilization, high Pt dispersion, acid tolerance, and well-characterized material as molecularitic metal oxide. © 2004 The Electrochemical Society. All rights reserved.
A138
Vladimir Petrovsky, Toshio Suzuki, Piotr Jasinski, Tatiana Petrovsky and Harlan U. Anderson
Thin-film electrolyte processing has become a key issue for the development of electrochemical devices such as solid oxide fuel cells, because reducing resistance of the electrolyte is critical to enhancing cell performance. In this study, yttrium-stabilized zirconia (YSZ) thin film, 1–2 μm thick, electrolyte has been prepared on dense and porous substrates using a combination of colloidal suspensions and polymer precursors at annealing temperatures <1000°C. Use of processing temperatures <1000°C minimizes interfacial reactions between electrolyte and anode/cathode materials. The conductivity of the thin film annealed at 900°C was measured and was the same as that of bulk YSZ and the processing temperature to obtain such conductivity was as low as 400°C. © 2004 The Electrochemical Society. All rights reserved.
A140
M. Ménétrier, C. Vaysse, L. Croguennec, C. Delmas, C. Jordy, F. Bonhomme and P. Biensan
and
magic-angle spinning (MAS) NMR spectra were recorded for
samples. The
MAS NMR signal of the layer on the pristine material is close to that of
in close contact with it. Its lineshape, due to dipolar interaction with electron spins of the material, is drastically different from that of pure
Upon hydration, this layer grows, while
NMR suggests that some lithium in the material is replaced by protons. Upon electrochemical cycling, the original layer is replaced by a different one, the solid electrolyte interphase, with distinct
and
NMR signatures, showing its largely organic nature. © 2004 The Electrochemical Society. All rights reserved.
A144
X. J. Chen, S. H. Chan and K. A. Khor
A148
Robert Larsen and Richard I. Masel
Pt/Pd is unusually active for formic acid electro-oxidation. While the oxidation of formic acid on Pt and Pt/Ru is poisoned by CO, the electro-oxidation of formic acid on Pt/Pd is not greatly inhibited by adsorbed CO. We examined CO stripping in the presence of formic acid and observed that the formic acid provides a continuous source of CO on Pt, Pt/Pd, and PtRu. CO stripping is slower on Pt/Pd than on the other catalysts even though Pt/Pd is unusually CO tolerant. Therefore, it is suggested that formic acid electro-oxidation occurs on a reaction site that is not inhibited by CO. © 2004 The Electrochemical Society. All rights reserved.
A151
Jinfeng Wu, Baolian Yi, Ming Hou, Zhongjun Hou and Huamin Zhang
A modified subcell approach was adopted to evaluate the current density distributions of proton exchange membrane fuel cells (PEMFCs) with different electrodes. Conventional hydrophobic electrodes showed better performance under flooding conditions compared to hydrophilic electrodes. The thin-film hydrophilic electrode performed better in the absence of liquid water, but it was more readily flooded. A composite catalyst layer was designed with 2/3 of the area from the inlet prepared hydrophilic and the remaining 1/3 area hydrophobic. The composite catalyst layer with commercial scale dimension showed notable enhanced performance in the concentration polarization region. © 2004 The Electrochemical Society. All rights reserved.
A155
Y. S. Meng, G. Ceder, C. P. Grey, W.-S. Yoon and Y. Shao-Horn
A159
K. Guérin, R. Yazami and A. Hamwi
Electrochemical/Chemical Deposition and Etching
C71
Oscar de Abril, Daniel Mandler and Patrick R. Unwin
A scanning electrochemical microscope (SECM) has been applied to the local deposition of Co microstructures on Au. The method employs a Co microelectrode to generate a potential-controlled flux of the respective ions in an aqueous solution. The microelectrode was positioned at a precisely defined distance above a gold surface using the steady-state current for oxygen reduction. The optimum conditions for Co dissolution and deposition were identified from voltammetry and chronoamperometry. Applying these conditions in the SECM configuration facilitated the successful deposition of Co structures. The dissolution and uptake of Co on the Au surface was investigated using SECM double potential step chronoamperometry. © 2004 The Electrochemical Society. All rights reserved.
C75
R. Henrı́quez, H. Gómez, G. Riveros, J. F. Guillemoles, M. Froment and D. Lincot
Results on the preparation and characterization of ZnSe epitaxial thin films obtained by electrodeposition on (111) and (100) n-type InP single-crystalline substrates, starting from elemental selenium dissolved in DMSO at 423 K, are reported. Voltammetric studies have been performed on these substrates and compared to
covered glass substrates. They show substrate dependent behavior and the presence of parasitic faradaic reactions attributed to the formation of di-selenide anions. However, composition analysis of the films by electron dispersive spectroscopy revealed that, independent on the substrate, nearly stoichiometric ZnSe films are obtained within the deposition potential range. Scanning electron microscopy images present a specific effect of chloride ion on the films morphology, whereas their optical characterization showed a direct band gap value of 2.64 eV. The epitaxial quality of the deposits has been confirmed by reflection of high energy electron diffraction and atomic force microscopy techniques. © 2004 The Electrochemical Society. All rights reserved.
C78
Shoso Shingubara, Zengling Wang, Osamu Yaegashi, Ryo Obata, Hiroyuki Sakaue and Takayuki Takahagi
Bottom-up fill of Cu in deep submicrometer via holes was achieved through electroless plating alone for the first time. We investigated the effect of addition of inhibitor molecules to electroless Cu plating solution, and found that sulfopropyl sulfonate (SPS) was highly effective in promoting the bottom-up fill. The tendency for bottom-up filling was enhanced by shrinkage of the hole diameter. This suggests that the diffusion flux of SPS molecules to the bottom of holes was more suppressed for smaller holes. Thus, the Cu deposition rate near the hole bottom is larger than that outside the hole, leading to bottom-up filling. © 2004 The Electrochemical Society. All rights reserved.
Electrochemical Synthesis and Engineering
D7
Nobuhito Imanaka, Toshiyuki Masui and Takanobu Chiga
Physical and Analytical Electrochemistry
E31
K. Noworyta and J. Augustynski
Photoactivities of
film electrodes formed in the flame of a burner fed with various gas mixtures were examined both under a relatively intense near UV light and under simulated solar illumination. The most significant shift of the spectral photoresponse (up to 425 nm) and the largest solar light induced photocurrents were observed for the
films grown in the reductive zone of a propane/butane-oxygen flame. The photoelectrochemical characteristics of the electrodes largely changed with the preparation conditions. Raman spectra revealed the presence of disordered carbon in the flame-formed samples in addition to lower nonstoichiometric titanium oxides identified by XRD. © 2004 The Electrochemical Society. All rights reserved.
Dielectric Science and Materials
F39
M. Bhaskaran, P. K. Swain and D. Misra
F42
H. S. Chang, S.-K. Baek, H. Park, H. Hwang, J. H. Oh, W. S. Shin, J. H. Yeo, K. H. Hwang, S. W. Nam, H. D. Lee et al
Semiconductor Devices, Materials, and Processing
G113
T. C. Chang, S. T. Yan, P. T. Liu, C. W. Chen, Y. C. Wu and S. M. Sze
G116
Kee-Chan Park, Woo-Jin Nam, Su-Hyuk Kang and Min-Koo Han
Incomplete annealing of the ion doping damage near the source/drain junctions of the excimer-laser-annealed polycrystalline silicon thin-film transistor has been observed by transmission electron microscopy. The degree of the incomplete annealing was increased with increasing gate thickness due to the laser beam diffraction at the gate electrode edge. Simulation of the laser beam diffraction showed that the laser intensity decreased considerably near the junctions and the width of reduced laser intensity region increased with increasing gate thickness. The incompletely annealed ion doping damage decreases the field-effect mobility considerably and increases the leakage current. © 2004 The Electrochemical Society. All rights reserved.
G119
Kow-Ming Chang, Wen-Chih Yang and Chu-Feng Chen
G122
T. C. Chang, T. M. Tsai, P. T. Liu, C. W. Chen, S. T. Yan, H. Aoki, Y. C. Chang and T. Y. Tseng
G125
Jihyun Kim, K. H. Baik, B. S. Kang, S. Kim, Y. Irokawa, F. Ren, S. J. Pearton and G. Y. Chung
G128
Jia-Hung Wu, Jia-Min Shieh, Bau-Tong Dai and YewChung Sermon Wu
Hydrogenated microcrystalline silicon (μc-Si:H) channel layers were synthesized at a temperature below 100°C by inductively coupled plasma (ICP) methods. High ionization efficiency and low ion bombardment from the ICP, enabled the use of high ICP power and, thus, extremely dense plasma or markedly increased electron temperature, promoting the diffusion capability of the reactive radicals that eventually yield ICP μc-Si:H films with large grains of several tens of nanometers, a high deposition rate of 5 Å/s, and a smooth roughness of
Accordingly, the epitaxial growth of μc-Si:H films at room temperature is demonstrated. © 2004 The Electrochemical Society. All rights reserved.
Sensors and Displays: Principles, Materials, and Processing
H23
Joung Kyu Park, Mi Ae Lim, Chang Hae Kim, Hee Dong Park and Se Young Choi
General Topics
J13
T. S. Zhang, J. Ma, L. B. Kong, P. Hing, S. H. Chan and J. A. Kilner