Carbon Nanostructures and Devices
M35
Wenxin Fan, Yanxiang Wang, Chengguo Wang, Jiqiang Chen and Yan Yuan
This article aimed at development of a catalyst for the highly efficient preparation of carbon nanotube (CNT)-grafted carbon fibers (CFs) with high mechanical properties by using chemical vapor deposition (CVD). Based on an innovative technique for the uniform coating of catalyst on the CF surface, the influence of catalyst type on the morphology and mechanical properties of CNT-grafted CFs has been systematically studied. It was found that trace addition of Cu can significantly enhance the catalytic activity of Fe catalyst, the corresponding tensile strength of final CNT-grafted CFs is 12.0% higher than the untreated CFs.
M38
R. Marani and A. G. Perri
In this paper we have implemented the semi-empirical compact model for CNTFETs already proposed by us to simulate typical analogue circuits and logic blocks both in SPICE, using ABM library, and in Verilog-A. The obtained results have been the same in static simulations and comparable in dynamic simulations. However using Verilog-A the simulation run time has been much shorter and the software has been much more concise and clear than schemes using ABM blocks in SPICE.
M44
Shaahin G. Shirazi, Gholamreza Karimi and Sattar Mirzakuchaki
For a carbon nanotube field effect transistor (CNTFET) the ballistic I-V characteristics have been investigated theoretically with respect to ambient temperature for both the p-i-n tunnel FET (TFET) and n-i-n metal-oxide-semiconductor FET (MOSFET). The performance stability of a TFET at higher temperatures, especially in subthreshold regime in which the n-i-n device exhibits a devastating characteristic, is appreciable. Alongside very low subthreshold swing even at a temperature beyond 300 K, a p-i-n tunnel FET could be a more reliable choice for operating in a wide range of temperatures. The subthreshold swing, transconductance, output conductance, saturation mechanism and on/off current ratio are also considered with respect to CNT diameter as well. A lower diameter lessens some negative effects of operating at a high temperature. All the results can be realized based on the energy band diagram of the device and the Fermi functions of source and drain. This trend gives a valuable insight into exploring the changes in 1D device characteristics.
M51
Xiaoqiang Peng, Junwei An, Shengming Xu, Weiliang Chen and Zhenghe Xu
In this paper, we report a method for the further reduction of the low-cost graphene (LG) via hydroiodic acid to synthesize graphene hybrid with varying content of δ-MnO2. Scanning electron microscope (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD) were implemented to characterize the surface and structural properties of the reduced graphene (LGHI) and graphene-MnO2 composites (GM). It can be observed that the thickness of LGHI layers is about 10∼200 nm and as-prepared GM composites have a uniform morphology possessing a honeycomb structure. XRD results indicate that MnO2 in the GM exists as a δ-crystallographic structure of low crystallinity. Cyclic voltammetry (CV) curves, galvanostatic charge/discharge (GDC) curves and electrochemical impedance spectroscopy (EIS) were utilized in a three-electrode system to systematically investigate the electrochemical performance of varying δ-MnO2 content materials. Results reveal that once the mass fraction of δ-MnO2 in GM reaches 93.1% (labeled GM-6), the specific maximum capacitance of GM was found to be 783 F/g, 496 F/g, 345 F/g and 210 F/g at a current density of 0.3 A/g, 1 A/g, 3 A/g and 10 A/g, respectively. Moreover, GM-6 maintains almost 94.5% of its original specific capacitance after 5000 continuous cycles of charge-discharge. These promising results demonstrate that GM-6 has great potential to be utilized as an electrode material for supercapacitor applications.
M58
Mazmira Mohamad, R. Ahmed, A. Shaari, Bakhtiar Ul Haq, Mohammed Benali Kanoun and Souraya Goumri-Said
The analysis of electrical and optical properties of organic semiconductor materials with quantum mechanics approaches is a comprehensive tool to get close outlook about their performance in optoelectronic devices. By adopting ab initio approach of Density Functional Theory (DFT) implemented within DMol3 code, optoelectronic characterization of isolated single molecule and molecular crystal in β phase of Cu-Phthalocyanine was studied. It was observed that the stacking herringbone geometry of CuPc molecule in β-CuPc subsequently initiates the formation of covalent bonding between the molecules. However reactions with copper atom, existence of nitrogen atoms and accumulation of free charges greatly affect the electronic properties of CuPc molecule and β-CuPc. The lingering of free charges in β-CuPc is found to give rise to dense electrons population accompanied with an intense optical spectra. An extremely high absorption and low value of the loss function have been observed on the optical part of this study as well.
Dielectric Science and Materials
N27
The following article is Open access
E. Simoen, R. Ritzenthaler, M.-J. Cho, T. Schram, N. Horiguchi, M. Aoulaiche, A. Spessot, P. Fazan and C. Claeys
The impact of the implementation of a high-κ/metal-gate (HKMG) stack on the oxide integrity of input-output (I/O) pMOSFETs for DRAM periphery applications is investigated by means of low-frequency (LF) noise spectroscopy. It is shown that the predominant 1/f noise is governed by number fluctuations, irrespective of the details of the gate stack. However, the trap density in the 5 nm SiO2 gate oxide, derived from the noise power spectral density is significantly increased by the application of the HKMG and/or Al2O3 cap and the subsequent diffusion anneal at 900°C.
N32
Woo-Jin Lee, Hideaki Fukuda, Tae Hyung Kim and Yong-Ho Choa
Photo-induced deposition of SiOCH thin films and their trench filling properties are discussed. Octamethyl-cycloterasiloxan (OMCTS) was used as a precursor and Xe2 excimer lamp was used as a light source. The deposition temperature was 80°C and the reactor pressure was maintained at 38.5 Pa. The relative permittivity of as-deposited film was 7.9. Due to the UV cure process, those OH-related bonds in the film were significantly decreased. The k-value of the UV cure film was 2.1. Photo-induced SiOCH was employed to achieve bottom-up filling of high-aspect-ratio features (A/S > 7.5).
Electronic Materials and Processing
P305
Rawnaq A. Talib, M. J. Abdullah, Sabah M. Mohammad, Naser M. Ahmed and Nageh K. Allam
Heterojunction photodiodes involving a wide bandgap semiconductor on polymeric substrates have a number of potential advantages such as excellent blue response, simple processing steps, and low processing cost. We report on the chemical synthesis of ZnO–polyaniline (PAni) composite thin films and their use for UV detection. The morphological and structural properties of the composites were characterized using X-ray diffraction (XRD), Raman spectroscopy, and field-emission scanning electron microscopy (FESEM). The XRD results demonstrated the formation of hexagonal wurtzite ZnO structure, with no noticeable change upon the addition of PAni. The FESEM images revealed the hexagonal microstructure of the ZnO-PAni composite films, with high porosity. Raman spectroscopy revealed the interfacial interaction between ZnO and PAni. Thin films deposited on glass, PET, and Si substrates were used to fabricate photodetector devices based on the ZnO-PAni composites. The photodetector made using Si substrate showed the best performance with a high gain of 108, sensitivity of 9842, and responsivity of 0.707A/W.
P309
The following article is Open access
S. Raghavan and C. C. Chiang
Electrochemical techniques have long been used in understanding and improving the performance of various wet chemical processing steps such as etching, cleaning, passivation and rinsing used in integrated circuit (IC) manufacturing. The objective of this paper is to provide a few examples of how electrochemical techniques can be used to probe some important areas in wet processing. It is not intended to be an exhaustive review of techniques and problems reported in the literature.
P315
J. B. Liu, J. Luo, E. Simoen, Y. X. Niu, F. Yang, G. L. Wang, W. W. Wang, D. P. Chen, J. F. Li, C. Zhao et al
The vacancy-enhanced rapid diffusion of N-type dopants especially phosphorus has been a hurdle for the development of germanium based complementary metal-oxide-semiconductor (CMOS) technology. Phosphorus diffuses quickly in germanium via the formation of Phosphorus-Vacancy (P-V) pairs. Trapping vacancies thus slowing down the rapid P diffusion by some elements like carbon, nitrogen and fluorine has proved to be effective. In this work, the junction control by carbon and P co-implantation in pre-amorphized germanium is investigated systematically. It is found that when the implanted C sits at the half range of the pre-amorphized germanium layer, the vacancy-enhanced diffusion of phosphorus and the resultant junction depth can be well controlled.
P320
Ji-Li Tian, Gui-Gen Wang, Hua-Yu Zhang and Jie-Cai Han
Nanopatterned silicon substrate has potential applications in the optoelectronic fields. However, its preparation is often complex and costly. In this paper, self-assembled anodic aluminum oxide (AAO) film masks on silicon substrates were deposited by a simple and feasible method, which was based on the direct anodization of sputtered Al film instead of previous reported Al/SiO2 or Al/Ti/SiO2 films. With the as-deposited AAO film masks other than common freestanding AAO templates, nanopatterned silicon substrates were finally obtained using two-step inductively coupled plasma (ICP) etching. The experimental results show that the pore arrangement of the AAO film has been successfully transferred to the silicon substrates after the ICP etching. The average diameter, wall thickness and depth for the as-obtained silicon nanopore arrays are approximately 65 nm, 40 nm, and 260 nm, respectively. It is believed that the above-proposed method has the potential for the fabrication of large-scale and uniform sub-100 nm nanopatterned silicon substrates.
P324
Mourad Benlamri, Samira Farsinezhad, Douglas W. Barlage and Karthik Shankar
We report the fabrication of Cu/ZnO Schottky diodes on flexible polyimide substrates that can retain high performance under substrate bending. The ZnO films are synthesized with an optimized low-cost electrodeposition technique on a thin copper (Cu) film adhered to a flexible Kapton substrate via a titanium (Ti) adhesion layer. The Cu/ZnO system constituted a Schottky diode that demonstrated rectification ratios of ∼106 and ideality factors of ∼2 to 3, which surpass the current state-of-the-art for solution-processed ZnO films.
P327
Jinjuan Xiang, Tingting Li, Xiaolei Wang, Kai Han, Junfeng Li and Chao Zhao
The role of TiN barrier layer on electrical performance of metal oxide semiconductor (MOS) with Si/SiO2/HfO2/ALD-TiN/ALD-TiAlC structure is investigated. It is found that the effective workfunction of TiN/TiAlC decreases with thinner TiN (in the range of 0∼3 nm). This is attributed to the lower workfunction of thinner TiN. The gate leakage Jg of the MOS capacitor with TiN barrier is slightly higher than that without TiN, while the equivalent oxide thickness is smaller. The reason is that the insertion of TiN between TiAlC and HfO2 can suppress Al diffusion and boost Ti diffusion into HfO2, leading to smaller EOT and larger leakage current. Moreover, the Jg with and without TiN are both 6 orders of magnitude lower than the traditional poly-Si/SiO2 stacks, which are lower enough for their application in device. These results are helpful to engineering the gate stacks of MOSFET.
P330
Juntao Li, Yangyang Xia, Bo Liu, Qing Wang, Dan Gao, Zhen Xu, Weiwei Wang, Zhitang Song, Gaoming Feng, YaoHui Zhou et al
Etch characteristics and mechanisms of TiSbTe thin films in inductively coupled HBr-He, HBr-Ar, HBr-N2, and HBr-O2 plasmas were studied in this paper. The etch rate of TiSbTe thin film was measured as functions of the additive gas fraction for He, Ar, N2 and O2 at a fixed gas pressure (5 mTorr, 1 mTorr = 0.133Pa), input power (700 W), bias power (300 W), and total gas flow rate (200 sccm). The etch rate and surface roughness of TiSbTe thin films showed non-monotonic behaviors as the increasing additive gas fraction in four plasma systems. Meanwhile, different kinds of additive gas resulted in different quantitative correlations between chemical and physical etching pathway, which eventually make difference on the etch rate and surface roughness of TiSbTe thin film. The surface chemical status of each component was also investigated in this study. The good performance of etch rate, surface roughness and low plasma damage suggested that HBr-Ar plasma is the best choice for TiSbTe etching compared with HBr-He, N2 and O2 plasma.
P335
The following article is Open access
S. F. Fu, C. H. Cheng, F. W. Lee, S. Y. Chen, B. W. Liao, W. C. Chou, W. K. Chen and W. C. Ke
Incorporation behaviors of In and Ga of InGaN films grown by the two-heater metal-organic vapor-phase epitaxial horizontal reactor is investigated by varying growth parameters, such as the substrate temperature, ceiling temperature and reactor pressure. Two In loss mechanisms are observed by the analysis of the concentration and temperature profiles in the deposition zone. The gas-phase parasitic-loss mechanism (activation energy ∼ 34.2 ± 0.1 kcal/mol) is significant in the ceiling temperature Tceil ≥ 800°C and at substrate temperature (Tsub) of 600°C. The decomposition-loss mechanism, which arises from In desorption on the growing surface, is significant in Tsub > 625°C region. The desorption activation energy obtained is 28.0 ± 0.1 kcal/mol, which is close to that of InN (25–26 kcal/mol). This suggests the In decomposition-loss mechanism in InGaN growth does not differ substantially from that in binary InN growth. On the other hand, the gas-phase parasitic-loss mechanism of Ga is negligible in the growth condition that we have explored. Exception is found for reactor pressure at Tceil = 950°C, where both factors advantageous and disadvantageous to Ga incorporation are unambiguously observed. We have proposed explanation for the above observation.
P340
The following article is Open access
Thomas Dequivre, Elias Al Alam, Josée Maurais, Gessie M. Brisard, J.-F. Pratte and Serge A. Charlebois
Via-Last metallization of High Aspect Ratio Through Silicon Via (HAR TSV) for 3D integration is challenging. Indeed, the formation of a uniform and conformal dielectric to insulate HAR TSVs in Via-Last process flow is difficult to achieve for any physical deposition process. In this study, we present the first reported HAR copper TSVs, insulated by highly conformal electrografted poly-4-vinylpyridine (P4VP) in Via-Last process-flow. As a demonstration, this allowed the metallization of HAR copper TSVs for die-to-die 3D integration of a 22 × 22 photodiode array tier onto a CMOS control electronics ASIC.
P345
Yan Mu, Rouchen Han, Yasa Sampurno, Yun Zhuang and Ara Philipossian
This study investigated the effect of two conditioner discs (i.e. “Disc A” and “Disc B”) during tungsten chemical mechanical planarization. Results showed that while pad temperature and removal rate increased with polishing pressure and platen velocity on both discs, “Disc B” generated consistently lower removal rates and coefficients of friction than “Disc A”. To fundamentally elucidate the cause(s) of such differences, pad surface contact area and topography were analyzed using laser confocal microscopy. The comparison of the pad surface micro-texture analysis on pad surfaces conditioned by both discs indicated that “Disc A” generated a surface having a smaller abruptness (λ) and more solid contact area which resulted in a higher removal rate. In contrast, “Disc B” generated many large near-contact areas as a result of fractured and collapsed pore walls.
P349
The following article is Open access
Sung-Kyu Lim, Do-Kywn Kim, Hae-Chul Hwang, Jin-Su Kim, Won-Sang Park, Young-Dae Cho, Chan-Soo Shin, Won-Kyu Park, Jung-Hee Lee, Dae-Hyun Kim et al
In this paper, we have investigated a pathway to mitigate the arsenic (As) cross-contamination on a back side Si wafer during GaAs growth by metal-organic chemical vapor deposition (MOCVD). Without a proper protocol doing a III-V on Si heterogeneous epitaxy, we have observed high levels of the As concentration on the back side Si wafer, easily in excess of 1 × 1020 atoms/cm3 by secondary ion mass spectrometry (SIMS) analysis and 1015 atoms/cm2 by total reflection X-ray fluorescence (TXRF) analysis, after GaAs growth on Si. This known level of contamination on wafers would disqualify them for fabrication in existing Si VLSI fabs. In order to mitigate the As cross-contamination, we have proposed a SiO2 protection layer on the back side of the Si wafer. From both SIMS and TXRF analysis, the proposed scheme has dramatically lowered the back side as concentration to 1.5 × 1016 atoms/cm3 by SIMS and 1.0 × 1010 atoms/cm2 by TXRF.
P353
Qian Zhou, Edwin Bin Leong Ong, Sin Leng Lim, Saumitra Vajandar, Thomas Osipowicz, Xiao Gong, Eng Soon Tok and Yee-Chia Yeo
Single crystalline germanium-lead (GePb) is formed using pulsed laser anneal (PLA). The anneal was performed on an amorphous GePb layer (1.1 atomic percent of Pb) capped by SiO2, Si3N4, or Al2O3 to study the impact of different capping layers on GePb formation. Among various laser fluences (300, 350, 400, 450, and 500 mJ/cm2) used, the best GePb crystalline quality was achieved using 350 mJ/cm2. Secondary ion mass spectrometry (SIMS) results show a final Pb composition in the GePb film after laser anneal of between 0.2 and 0.4 atomic percent, indicating a significant loss of Pb. Among the different capping layers used, Al2O3-capped GePb shows the highest Pb content in the GePb layer with the lowest Pb loss after PLA. The incorporation of Pb atoms in the substitutional sites of Ge lattice was confirmed by high resolution X-ray diffractometry (HRXRD) and high resolution Rutherford back scattering spectrometry (HR-RBS). The substitutionality, i.e. percentage of Pb atoms incorporated into substitutional sites of Ge lattice, is more than 70%. The anneal process leads to the formation of cavities in the GePb layer and pin holes on the surface, suggesting an out-diffusion of Pb from the GePb thin-film during laser anneal. Increasing the laser anneal fluence above 400 mJ/cm2, however, reduces the number of cavities and pin holes but increases the surface roughness of the film.
P361
The following article is Open access
Kun Xu, Shih-Haur Shen, Jason Fung, Hassan Iravani, Ingemar Carlsson, Tzu-Yu Liu, Bogdan Swedek, Shou-Sung Chang, Wen-chiang Tu, Tomohiko Kitajima et al
This study investigated the effects of tungsten (W) film morphology on the chemical mechanical polishing (CMP) of W. Chemical vapor deposited (CVD) W films with two distinctively different grain sizes were used for comparison. During polishing, W film thickness and optical reflectance, friction, and pad temperature were monitored in-situ. It was found that larger-grained W film took longer to pass the initial low removal rate stage. By correlating four different sensor signals, comparing friction dependency on film morphology, in slurry vs. DIW, it was concluded that W CMP comprises three main stages. First is the low rate initiation stage: grain is being partially planarized, reflectance increases, friction decreases. Second is the transition stage: rate is ramping, grain becomes fully planarized, optical reflectance reaches maximum, and friction becomes minimal followed by a significant rise caused by formation of tungsten oxide passivation layer on the planarized W surface. Third is the high and constant rate stage: passivation and removal occur in a repetitive cycle, friction is high and stable, optical reflectance changes as polishing reaches different film depths. In all three stages, pad temperature increases continuously as friction-induced heat dissipates, with the rate of temperature increase following that of friction magnitude.
P368
Bin Zhu, Kate E. Roach, David M. Lynch, Chen-yang Chung, Dieter G. Ast, Raymond G. Greene and Michael O. Thompson
The influence of deposition parameters on the properties of RF sputter deposited c-axis aligned crystalline (CAAC) IGZO was studied using both single parameter and design of experiment (DOE) analysis (target composition near InGaZnO4). Use of a 3-level, 6 factor Box-Behnken DOE enabled efficient sampling of the large processing parameter space. Deposition temperature and power, oxygen fraction in the sputter gas, and the ensuing Zn composition were identified as the key parameters correlated with c-axis texture in the films. CAAC formation commenced at a deposition temperature of 250°C reaching maximum surface normal alignment near 315°C. Crystallinity and alignment increased rapidly with oxygen fraction becoming nearly independent of fraction between 10% and 50%. Zinc loss during deposition at high temperatures and low oxygen partial pressures correlated with lower crystallinity, suggesting a strong composition dependence of CAAC formation in IGZO alloys. In contrast, increased deposition power improved alignment. Optimal deposition conditions were identified and related to a proposed nucleation and growth model.
Electronic and Photonic Devices and Systems
Q145
The following article is Open access
Akinobu Hayakawa and Takashi Sagawa
Thin-film making process for highly efficient poly(3-hexylthiophene)-2,5-diyl (P3HT) and zinc oxide (ZnO) nanoparticles hybrid solar cell was optimized with or without ligand of indoline dye as the dispersing agent for ZnO. Increment of the short circuit current density was observed after the addition of the ligand to the mixture of P3HT and ZnO. Further quenching of the emission of P3HT by ZnO with the ligan than that without the dye was also observed. It was found the 1.5 times enhancement of power conversion efficiency by addition of the dispersing agent. Impedance analyses to evaluate parallel resistance (Rp) and series resistance were investigated and found thickness dependence of the Rp. Current density of P3HT-ZnO hybrid system is crucially affected by the interfacial resistance of the grain boundaries of ZnO.
Q149
The following article is Open access
Chen-Pin Hsu, Yu-Fen Huang and Yu-Lin Wang
In this study, non-faradaic current was measured in time domain and investigated on a DNA-immobilized electrode in concentrated salt environment for biosensor applications. The electric current was measured for 50 μs once the pulse voltage of 0.5 V was applied to the electrode. Immobilization of double-stranded DNA (dsDNA) caused the electric current increased, compared to the electrode without any immobilization. Doxorubicin, ranging from 1 pM to 1 nM, intercalated the dsDNA and caused different relaxation of the electric currents. The characteristics of electric current for different surface modification on the electrode was compared and successfully explained with the ion concentration, ion mobility, and the electric field in solution. Instead of the impedance measurement, which usually extracts parasitic parameters for biosensor applications, this study directly explains the relevance between the electric current and the behavior of molecules in solution, with the proposed model. This method can be applied to any affinity type of biosensors. The three indexes, including the current level, the total charge, and the relaxation time can be directly used as signals for detection, which is much simpler compared to other existing techniques.
Q155
Kuan-Ju Liu, Ting-Chang Chang, Chien-Yu Lin, Ching-En Chen, Jyun-Yu Tsai, Ying-Hsin Lu, Hsi-Wen Liu, Osbert Cheng and Cheng-Tung Huang
This work demonstrates an abnormal transconductance (GM) enhancement after positive bias stress (PBS) in n-channel high-k/metal gate stacked fin-field-effect-transistors. This abnormal GM enhancement is observed only in short channel devices. With the speculation that hole-trapping-induced electron accumulation is the dominant mechanism, PBS with floating source and drain is adopted as an investigative approach. This, together with the electric field simulation, verifies that hole-trapping in the HfO2 and SiN near the gate corner induces electron accumulated at the ends of the channel length. Such a phenomenon results in a shortening of effective channel length and further GM enhancement.
Q160
A. Mai, S. Lischke, M. Wietstruck, L. Zimmermann, M. Kaynak and B. Tillack
The purpose of this work is to review requirements and challenges for the monolithic integration of different devices and modules in a baseline CMOS-process with the intention to create a multifunctional technology platform. We consider integrated modules like THz devices, i.e. complementary SiGe heterojunction bipolar transistors, silicon photonics components in particular Ge-PIN photo detectors and the wafer-level integration of micro-fluidic channels for sensor applications. However, the monolithic integration of devices and modules for novel functionalities is still a trade-off. On the one side there are requirements of the integration concept and therefore to the process steps of the dedicated module to achieve a maximum device performance. On the other side there are influences of the process steps for the module integration to the performance of the devices from the underlying baseline technology like bipolar- and CMOS-transistors or passive components. Both aspects have to be considered to enable the co-integration of new modules in order to get a technology platform for high performances and novel functionalities. We review process adaptations of the baseline technologies to enable an efficient co-integration of different modules. Moreover we discuss critical process steps with a certain thermal budget and their influence to device performances. Finally we give recommendations for process sequences to enable a wafer level co-integration of microfluidic channels into a SiGe-BiCMOS technology platform.
Q165
A. Y. Polyakov, Han-Su Cho, Jin-Hyeon Yun, In-Hwan Lee, E. B. Yakimov, N. B. Smirnov and K. D. Shcherbachev
GaN/InGaN multiple quantum well (MQW) structures with undoped n-GaN cap imitating true light emitting diodes were grown on sapphire and converted to deep nanopillar (NP) structures by dry etching beyond the MQW region. Structural measurements, electrical measurements on Schottky diodes, microcathodoluminescence (MCL) spectra measurements indicate a strong relaxation of strain in NP MQWs manifested in the prominent increase of the bowing radius of the structures and in the blueshift of the MQW peak in MCL spectra. Various treatments of the as-etched NP MQWs (annealing at 700°C, etching in KOH, and soaking in (NH4)2S) progressively decreased the leakage current of Schottky diodes and increased the MQW MCL peak intensity due to the suppression of the dry-etching damage of the nanopillar sidewalls.
Q171
Jun-Feng Wei, Qiao-Ling Wu, Yue-Xia Lin and Yong Zhang
In this work, well-controlled ambient humidity can adjust the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films during an acetic acid rinse. The conductivity of PEDOT:PSS films can be dramatically enhanced by optimizing post-treatment ambient humidity. The conductivity of PEDOT:PSS films increase from 0.33 S/cm for the pristine to 1090 S/cm at relative humidity (RH) of 60% while that of PEDOT:PSS films is only 5.04 S/cm at H2O < 1 ppm. The improvement conductivity should be attributed to enhanced phase segregation, removing of some PSS chains from PEDOT:PSS and reorganization of PEDOT chains at higher RH. This facile solvent-treated route provides a promising transparent electrode fabrication method to replace ITO electrode in organic photovoltaics (OPVs).
Q176
T. J. Anderson, J. D. Greenlee, B. N. Feigelson, J. K. Hite, F. J. Kub and K. D. Hobart
The realization of selectively implanted p-type regions in GaN as well as an understanding of processing effects that cause carrier type conversion are key enabling steps for vertical GaN devices. Here, GaN Schottky barrier diodes (SBDs) with edge termination formed by either a field plate or junction termination extension (JTE) achieved by ion implanted and symmetric multicycle rapid thermal annealing (SMRTA) are presented. The devices with JTE exhibited substantially reduced leakage currents and improved turn-on characteristics. This is attributed to the elimination of the plasma process steps associated with the deposition and patterning of the field oxide layer required in a field plate process. The breakdown characteristics were studied by electroluminescence imaging, and is indicative of avalanche behavior. The realization of vertical GaN devices with low reverse leakage and ion implanted termination regions represents a key step for future power electronic devices.
Q179
C. K. Wang, Y. Z. Chiou, P. K. Lin, J. S. Jheng, S. P. Chang and S. J. Chang
The numerical simulations of blue InGaN/GaN light-emitting diodes (LEDs) with the combined structures of p-GaN/InGaN short-period superlattice (SPS) last barrier (LB) and p-AlGaN/GaN SPS electron blocking layer (EBL) are investigated by the Advance Physical Model of Semiconductor Devices (APSYS) program. The simulation results show that the newly designed LEDs get better performances over the original structure of InGaN/GaN LEDs. This is attributed to the enhancement of the hole injection efficiency and the improvement of the polarization field effect between the InGaN well and the GaN barrier layer in the multiple quantum wells (MQWs). Therefore, the simulation results exhibit a significant increment in radiative recombination rate and about 2.6 times enhancement in the internal quantum efficiency (IQE) at an injection current of 150 mA. More important of all, it also shows that the newly designed structure can obviously reduce the ratio of efficiency droop of the LEDs from 62 to 14.5%.
Q183
Mahmoud Abdelfatah, Johannes Ledig, Abdelhamid El-Shaer, Azat Sharafeev, Peter Lemmens, Mohsen Mohamed Mosaad, Andreas Waag and Andrey Bakin
We present here a direct comparison of potentiostatic and galvanostatic modes of Cu2O thin films electrodeposition for the manufacturing of solar cells keeping all other steps identical. The ZnO:Al window layers were deposited using sputtering. The solar cells were characterized by scanning electron microscopy and Raman spectroscopy that show pyramidal shape and phonon modes for Cu2O thin films, respectively. Current – voltage (J-V), capacitance – frequency (C–f) and the external quantum efficiency (EQE) measurements were performed to understand the heterojunction properties. The results show that there is no big difference in Voc values comparing devices manufactured by the potentiostatic and the galvanostatic mode. While the Jsc values for the case of potentiostatic growth mode are higher compared to the galvanostatic one even for the same thin film thickness, this difference can be attributed to the textured top surface morphology of the devices and the minority carrier diffusion length (Ldiff) as concluded from SEM and EQE measurements. For solar cells grown by the galvanostatic mode with Cu2O thin film thickness increasing from 1 to 2.3 μm the efficiency increases by around 19.3%, while it increases by around 27.7% for devices grown by the potentiostatic mode. Overall, devices grown by a potentiostatic mode have higher efficiency than those from a galvanostatic mode.
Q188
Jiyong Woo and Hyunsang Hwang
A back-to-back Schottky diode configuration employing an ultrathin TiO2 layer has been assessed for application as a bi-polar selector in resistive random access memory by considering such factors as its working principle and scaling trends. Although higher rectification was achieved with an extremely low leakage current by the formation of a Schottky barrier, the maximum current remained low. This lower driving current can, however, be improved through engineering the properties of the TiO2 layer. Finally, the device characteristics of a scaled-down to ∼30 nm were observed, the results of which strongly suggest that the device characteristics are governed by its whole area.
Luminescence and Display Materials, Devices, and Processing
R83
Claudia Bizzarri, Charlotte Fléchon, Oliver Fenwick, Franco Cacialli, Federico Polo, María Dolores Gálvez-López, Cheng-Han Yang, Simone Scintilla, Yinghui Sun, Roland Fröhlich et al
Four novel neutral copper(I) compounds were prepared, based on the chelating phosphine bis(2-(diphenylphosphino)phenyl)ether, (DPEPhos), and a series of nitrogen-containing heterocycles as ancillary ligands. The optical properties can be tuned according to the ancillary ligand and their emissions at room temperature in aprotic solvent (CH2Cl2) go from greenish blue to orange. Their photoluminescence in solid state is particularly attractive and make their employment in opto-electronic devices very appealing. In particular, the low-cost preparation method of solution-processed light emitting devices is suitable for copper(I) complexes. In order to choose a suitable device architecture, the electrochemical characteristics were investigated and the frontier orbitals values were determined. Preliminary results on solution-processed OLED are presented.
R91
Thomas Jansen, David Böhnisch and Thomas Jüstel
This work deals with the saturation behavior of Eu2+ doped luminescent materials. Eu2+ activated phosphors, excited by high radiance pump sources, like high power LEDs or Laser Diodes, offer considerable potential for high radiance conversion in Solid State Lighting. Remarkably, theoretical arguments suggest that the radiance of the luminescent spot should increase linearly with the excitation density of the incoming light source up to 1 kW/mm2. In practice, however, thermal quenching and (non-thermal) optical saturation limit the maximum attainable radiance of the luminescent material. We present experimental data of the widely applied red emitting LED phosphors (Ca,Ba)2SiO4:Eu2+ (OSE), Ba2Si5N8:Eu2+ (258:Eu), and CaAlSiN3:Eu2+ (CASN:Eu) in which these limits have been investigated. High excitation fluxes are achieved using laser pumping at 405 nm up to 800 W/mm2. In case of 258:Eu and CASN:Eu, optical pumping intensities have been shown to produce a significant efficiency depreciation already at low pump powers, which does not correlate with the relatively short Eu2+ luminescence lifetime (∼1 μs). We assume a de-excitation mechanism that depletes the excited state [Xe]4f 65d1 to the conduction band of the host structure, which bottlenecks the limit maximum pump intensities. We find that the investigated Eu2+ phosphors tend to show different efficiency depreciation. Finally, we use a rate equation model to simulate this nonlinear optical pumping.
R98
Sourav Das, J. Manam and S. K. Sharma
A novel rhodamine 6G dye encapsulated mesoporous SiO2/SrAl2O4:Eu2+, Dy3+ composite yellow long lasting phosphor was prepared based on the color conversion process. The color conversion was achieved by mixing rhodamine 6G dye encapsulated mesoporous silica nanoparticles (MSNp-Rh6G) with SrAl2O4:Eu2+, Dy3+ (SAO) long persistent phosphor in a mass ratio. The X-ray diffraction, Field Emission Scanning Microscopy, Transmission Electron Microscopy, photoluminescence, phosphorescence, and decay curve were utilized to characterize the composite phosphor. The photoluminescence emission spectrum of SAO is overlapped with the excitation spectrum of MSNp-Rh6G which indicates the rhodamine 6G dye encapsulated mesoporous silica nanoparticles can be excited by the phosphorescence emission of SAO. The phosphorescence emission of the composite long persistent phosphor can be tuned from green to yellow by changing the mass ratio of MSNp-Rh6G/SAO. A yellow phosphorescence emission was achieved with color co-ordinates (0.40, 0.50). The decay curves of the composite MSNp-Rh6G/SAO phosphor shows that the decay due to the peak of SAO and MSNp-Rh6G has similar decay kinetics which indicates the constant and steady color during decay process. The detailed color conversion process is described here. The results indicate that the composite LLP can be potentially applicable as a new long lasting phosphor used in the field of emergency light, display, luminous paint.
R104
Hsin-Wei Lu, Huei-Ling Weng, Po-Ching Kao, Sheng-Yuan Chu and Yung-Der Juang
In this study, blue-violet organic light emitting diodes (BV-OLEDs, ITO/MoO3 (Y nm)/4,4′-bis(9-carba-zolyl)-2,2′-biphenyl (CBP) (X nm)/1,3,5-tris(N-phenylbenzimidazole-2-yl)benzene (TPBi) (100-X nm)/LiF (1 nm)/Al (100 nm)) were fabricated with the simple bilayer structure of CBP and TPBi, leading to a maximum luminance of 1280 cd/m2 when the thicknesses of the MoO3, CBP, and TPBi were 4, 35 and 65 nm, respectively. The blue-shift of the electroluminescence was observed from various viewing angles, and is attributed to the micro-cavity effects. Further, it was observed that the Commission Internationale de l'Eclairage (CIE) chromaticity coordinates of the devices changed from (0.19, 0.102; at 4 V) to (0.333, 0.366; at 11 V) due to the electroplex effect between the CBP and TPBi at high voltage. Subsequently, simple white OLEDs (WOLEDs) were fabricated by combining the proposed BV-OLEDs with the down color conversion layer (CCL). The down CCL of the 5 wt% 5,6,11,12-tetraphenylnaphthacene (Rubrene)-doped 4,4′-bis(2,2-diphenylvinyl)-1,1′-biphenyl (DPVBi) had the highest maximum luminance of 1240 cd/m2, with measured CIE chromaticity coordinates of (0.333, 0.351) in the WOLEDs.
R110
Kamala N. Bhat, Ross S. Fontenot, William A. Hollerman and Mohan D. Aggarwal
Europium tetrakis dibenzoylmethide triethylammonium (EuD4TEA) is one of the most intense triboluminescent (TL) materials currently known. The authors have reported in 2011, that the intensity of emission can be enhanced by changing the starting europium salt from europium chloride to europium nitrate by 82%. While investigating the impact of solvents on the intensity of light emission, the authors in 2012, demonstrated that replacing anhydrous ethanol with laboratory grade ethanol showed no change in the observed TL results. However, changing the solvent from ethanol to acetone resulted in faster precipitation of the compound, and slow crystallization yielded larger crystals with higher intensity of triboluminescence. As a result of this research, this paper investigates the effect of solvent dilution using deionized water on the triboluminescent properties of EuD4TEA.