BATTERIES, FUEL CELLS, AND ENERGY CONVERSION
A1989
Peter J. Bouwman, Wojtek Dmowski, Jason Stanley, Gregory B. Cotten and Karen E. Swider-Lyons
A1999
Guangyu Lin, Wensheng He and Trung Van Nguyen
This paper describes a two-phase, one-dimensional steady-state, isothermal model of a fuel cell region consisting of the catalyst and gas diffusion layers bonded to a proton exchange membrane (PEM). A thin film-agglomerate approach is used to model the catalyst layer. The effect of water flooding in the gas diffusion layer and catalyst layer of the cathode on the overall cell performance was investigated. The simulation results confirmed that the water-flooding situation in the catalyst layer is more severe than that in the backing layer since water is first produced in the catalyst layer. The catalyst layer should be considered as an individual domain. The effect of operating parameters that affect the water generation and removal process, such as the inlet relative humidity of the cathode and anode streams and operating temperature was studied. The results show good agreement with the experimental observations. © 2004 The Electrochemical Society. All rights reserved.
A2007
Michael S. Ding and T. Richard Jow
Electrolytes of 
LiBOB,
and
in propylene carbonate-diethyl carbonate (PC-DEC) and propylene carbonate-ethylene carbonate (PC-EC) binary solvents were compared for their electrolytic conductivity (κ) and viscosity (η) to assist their application to the batteries and capacitors and to understand the mechanisms underlying the differences in these properties. For η, the
-salts resulted in considerably higher values than the
-salts, and the influence of an anion was such that the larger its size, the higher the η of the electrolyte. Correspondingly, κ of the
-electrolytes was substantially higher than the
-electrolytes, and a larger anion was accompanied by a lower κ, except for electrolytes at the low-η end. Toward this end, the order of κ tended to be in reverse: the κ of an electrolyte with a larger anion rose relative to one with a smaller anion. All evidence presented leads to the conclusion that the η, and thereby the κ, of the electrolytes are dominantly affected by the number of unassociated
ions through their solvation by the carbonate solvent molecules, the different anions of the Li-salts exerting their influence only through altering the number by their different powers for associating with the
© 2004 The Electrochemical Society. All rights reserved.
A2016
A. Panchenko, M. T. M. Koper, T. E. Shubina, S. J. Mitchell and E. Roduner
A2028
C. Ziegler, A. Schmitz, M. Tranitz, E. Fontes and J. O. Schumacher
A theoretical study of a planar and self-breathing fuel cell is presented. This work contains the development of a mathematical model for planar self-breathing fuel cells, the validation of the model, and a study of the behavior of this type of fuel cell. The mathematical model presented is two-dimensional and nonisothermal. The validation of the model is performed by comparison of the measured overall performance of a planar self-breathing fuel cell to the predictions of the model. For this type of cell, the maximum power density is in the range between 0.5 and 0.4 V, so the model is applied to study the behavior of the reference cell at a cell voltage of 0.4 V. The results of this study show the gas distribution, the potential distribution, and the temperature distribution are influenced strongly by the geometric design of the cathode end plate. The charge generation rate in the active area of the cathode and anode is affected by the ribs of the cathode end plate. A strong nonuniformity of the current distribution in the cathode is found. © 2004 The Electrochemical Society. All rights reserved.
A2042
Takashi Itoh, Koji Abe, Kaoru Dokko, Mohamed Mohamedi, Isamu Uchida and Atsuo Kasuya
A2047
Kazuki Arihara, Lanqun Mao, Paul A. Liddell, Ernesto Marino-Ochoa, Ana L. Moore, Tatsuya Imase, Dun Zhang, Tadashi Sotomura and Takeo Ohsaka
A2053
Piotr Piela, Christian Eickes, Eric Brosha, Fernando Garzon and Piotr Zelenay
In this study, we provide electrochemical and X-ray fluorescence evidence of ruthenium crossover in direct methanol fuel cells using a state-of-the-art Pt-Ru alloy catalyst at the anode. We find ruthenium susceptible to leaching out from the highly active Pt-Ru black catalyst, crossing the proton-conducting Nafion membrane and redepositing at the Pt cathode on the opposite side of the fuel cell. After first detecting this phenomenon in a direct methanol fuel cell (DMFC) stack with a history of cell-voltage reversal, we have since observed ruthenium crossover under virtually all DMFC operating conditions, from single cell break-in (humidification) to stack life testing. The degree of cathode contamination by ruthenium species (of chemical form yet unknown) depends on, among other factors, the DMFC anode potential and the cell operating time. Once deposited at the cathode, ruthenium inhibits oxygen reduction kinetics and the catalyst’s ability to handle methanol crossover. Depending on the degree of cathode contamination, the overall effect of ruthenium crossover on cell performance may be from as little as
up to 200 mV. © 2004 American Institute of Physics. All rights reserved.
A2060
Yung-Tai Wu and Chi-Chang Hu
A2067
The following article is Free article
Sang-Eun Cheon, Soo-Seok Choi, Ji-Seong Han, Yun-Suk Choi, Bok-Hwan Jung and Hong S. Lim
The cycle life and capacity fading mechanisms of secondary sulfur electrodes prepared by two different electrode fabrication methods were studied in an effort to improve the energy density of the cathode. Cycle life improved substantially when the uniformity of carbon distribution around the sulfur particles improved and electrode density increased, improving the overall structural integrity of the carbon matrix. Capacity fading in a high-energy-density cathode is mainly due to structural failure by physical crack propagations of the electrode structure and subsequent formation of the electrochemically irreversible
layer at cracked surfaces of carbon particles or masses. The capacity fading due to these mechanisms appears to be reduced substantially and significantly by improved structural integrity with uniform pore structure of the carbon matrix. A Li/S cell containing a cathode fabricated by the improved technique cycled over 400 cycles without any severe structural damage of the electrode structure. © 2004 The Electrochemical Society. All rights reserved.
A2074
M. P. Bichat, T. Politova, J. L. Pascal, F. Favier and L. Monconduit
A2082
Junwei Jiang, Jun Chen and J. R. Dahn
The reactions of discharged 
or discharged mesocarbon microbead
with ethylene carbonate/diethyl carbonate (EC/DEC) (1:2 by volume) solvent, 1 M
EC/DEC or 0.8 M LiBOB EC/DEC are compared using accelerating rate calorimetry (ARC). We find that
(1.5 V vs. Li) shows lower reactivity than
(0.05 V vs. Li) in EC/DEC solvent or in
-based electrolyte. The reactions between both electrodes and 1 M
EC/DEC proceed in a clear stepwise fashion, where first, intercalated lithium reacts with
(from the decomposition of
to produce LiF, and then, when the
is consumed, the remaining lithium reacts with the solvents. The addition of 0.8 M LiBOB to EC/DEC solvent greatly increases the thermal stability of both
and
X-ray diffraction (XRD) studies show that both
and
react with EC/DEC or LiBOB EC/DEC to produce
at the end of the ARC experiments. XRD studies show that
reacts with 1 M
EC/DEC to form LiF, 
and some
In fact, even a fresh sample of
reacts with 1 M
EC/DEC to produce substantial quantities of
and LiF, but little heat is evolved during this reaction since the Li in
is so tightly bound. The results in this paper suggest that safer lithium-ion cells could be built using
negative electrodes than with graphite negative electrodes. © 2004 The Electrochemical Society. All rights reserved.
A2088
Teko W. Napporn, Xavier Jacques-Bédard, François Morin and Michel Meunier
Single-chamber cells of two different types have been operated between 700 and 800°C in various methane-air mixtures. These cells are made mostly of conventional materials for solid oxide fuel cells (SOFCs), strontium-doped lanthanum manganite, yttria-stabilized zirconia (YSZ), and Ni-YSZ cermet. One type is electrolyte-supported, while the other represents a state-of-the-art fabrication for anode-supported cells. The anode-supported cells operate in a narrower range of methane-air ratios, but offer remarkable maximum specific powers, 360 and 285 mW/cm2 at 800 and 700°C, respectively. Some theoretical considerations about the actual operation of these cells are also provided. © 2004 The Electrochemical Society. All rights reserved.
A2095
Masayuki Nogami, Yoshie Tarutani, Yusuke Daiko, Seiji Izuhara, Toshiaki Nakao and Toshihiro Kasuga
A2100
Tao Gu, W.-K. Lee, J. W. Van Zee and M. Murthy
A2106
Kang Xu, Unchul Lee, Sheng S. Zhang and T. Richard Jow
In an attempt to depict a dynamic picture of solid electrolyte interface (SEI) formation on a graphitic anode surface during the initial forming cycle, we employed X-ray photoelectron spectroscopy in combination with a “pre-formation” technique to establish the dependence of the surface chemistry on the forming potential of the anode. A progressive transition in the 1s electron binding energies of the major elements was observed as the lithiation proceeded. However, the surface chemical species as well as their abundances seemed to stabilize around 0.55 V and remained constant during the subsequent delithiation process, indicating that a stable SEI exists thereafter. Integrating the information revealed by different analyses, we believe that the reductive decomposition of the
anion starts at ca. 1.00 V, while the effective protection of the graphene surface by SEI is available after the anode is lithiated below the potential of 0.55 V vs. Li. © 2004 The Electrochemical Society. All rights reserved.
A2113
Ricardo Alcántara, Pedro Lavela, Gregorio F. Ortiz, José L. Tirado, Radostina Stoyanova, Ekaterina Zhecheva and Juan Miguel Jiménez Mateos
Petroleum coke has been heat-treated in the presence of
at 800, 850, and 900°C, and the behavior of the resulting mixture as active electrode material has been evaluated in lithium test cells. X-ray diffraction analysis and scanning electron microscopy revealed that iron oxide was reduced and the carbon texture was modified on heating the carbon/iron oxide mixture. A significant improvement of capacity retention was observed for iron-containing carbon-based electrodes. The changes have been explained by the modification of the carbon surface during annealing with iron oxide, and by the formation of an amorphous protective layer through reduction of iron oxide during the electrochemical reaction with lithium. Electron paramagnetic resonance revealed the participation of iron in reversible redox processes. Impedance spectra showed better stability of the iron-containing carbon-based electrodes. © 2004 The Electrochemical Society. All rights reserved.
A2120
B. Yang and A. Manthiram
A2126
Huabin Yang, Haichang Zhang, Xiaodan Wang, Junhong Wang, Xianling Meng and Zuoxiang Zhou
Calcium zincate has been successfully synthesized by a high-energy ballmilled method. The crystal structure, chemical composition, surface morphology, granularity distribution, and electrochemical performance have been investigated to compare with that prepared by a conventional chemical precipitation method. X-ray powder diffraction results revealed that the calcium zincate prepared by the two methods had a well-defined monoclinic structure using a Rietveld refinement method. Scanning electron microscope images and granularity analysis indicated that the ballmilled material was a finer powder with a higher specific surface area. The thermogravimetric and differential thermal analysis showed that there was a slight difference in the crystalline water content in the chemical composition of the powders prepared by the two methods. The galvanostatic charge and discharge results showed that the ballmilled powder had a promising cyclic behavior due to the better electrochemical stability as revealed from the cyclic voltammetry. It is suggested that the ballmilled calcium zincate is more suitable for applications in secondary alkaline batteries. © 2004 The Electrochemical Society. All rights reserved.
A2132
Keijiro Sawai and Nobuhisa Suzuki
Nonplatinum electrocatalysts for air cathodes showing higher activity than the conventional Pt/C catalysts were prepared by heat-treating cobalt hexacyanoferrate precursors dispersed on carbon support under an inert atmosphere. The activity for oxygen reduction was examined by polarization measurements with a gas-diffusion electrode floating on the surface of an electrolyte under an air atmosphere at room temperature. The electrolyte used was a neutral phosphate buffer solution. To investigate the effect of carbon support on the catalytic activity, different types of carbon supports were used with and without pretreatment with nitric acid prior to dispersion of the inorganic precursor. Among several carbon supports examined, the high-area carbon pretreated with nitric acid at higher concentrations than 8 M led to an enhanced performance for oxygen reduction in the gas-diffusion electrode. The effect of Co/Fe ratio in the precursor on the catalytic activity was also investigated. The catalyst prepared by heat-treating the inorganic precursor with a Co/Fe ratio of 1.2 dispersed on the high-area carbon showed the highest activity. Concerning the polarization voltage for oxygen reduction with the floating electrode, the best catalyst prepared in this study exhibited ca. a 200 mV higher potential at 100 mA cm−2 than the carbon-supported Pt-black catalysts. The remarkable enhancement in the performance of the air cathodes seems to be due to high dispersion on the high-area carbon, leading to effective utilization of the catalyst in addition to its intrinsic activity. © 2004 The Electrochemical Society. All rights reserved.
A2138
P. Reale, S. Panero, B. Scrosati, J. Garche, M. Wohlfahrt-Mehrens and M. Wachtler
A polymer lithium-ion battery, formed by a
electrode combination and a poly(vinylidene fluoride) (PVdF)-based gel electrolyte, is presented and discussed. The electrochemical characterization demonstrates that this battery is capable of delivering appreciable capacity values at rates ranging from C/32 (160 mAh g−1) to 0.75C (130 mAh g−1), this being accompanied by a remarkable cycle life. In addition, because the two electrodes are based on common and nontoxic materials and operate within the stability window of the electrolyte, the battery is expected to be safe, inexpensive, and compatible with the environment. All these properties make the battery of prospective interest for application in the hybrid and electric vehicle field. © 2004 The Electrochemical Society. All rights reserved.
A2143
J. R. C. Salgado, E. Antolini and E. R. Gonzalez
A Pt-Co/C electrocatalyst with Pt:Co atomic ratio 85:15, prepared by a low-temperature chemical reduction with sodium borohydride, was studied as possible cathode material for polymer electrolyte membrane fuel cells (PEMFCs). The physical characterization of this electrocatalyst was performed by energy-dispersive X-ray analysis, X-ray diffraction, and transmission electron microscopy. The performance of the material was evaluated by cyclic voltammetry and polarization experiments in a single PEMFC and compared with those of an unalloyed Pt/C catalyst prepared by the same method and a commercial Pt-Co/C catalyst. Both the Pt-Co/C catalysts were also submitted to a thermal treatment in a reducing atmosphere. © 2004 The Electrochemical Society. All rights reserved.
A2150
Yu Seung Kim, Michael J. Sumner, William L. Harrison, Judy S. Riffle, James E. McGrath and Bryan S. Pivovar
This paper reports the performance of direct methanol fuel cells (DMFCs) using novel disulfonated poly(arylene ether benzonitrile) copolymers derived from hexafluoro-isopropylidene diphenol (6F), 2,6-dichlorobenzonitrile, and 3,3′-disulfonated
-dichloro diphenyl sulfone (SDCDPS). The membrane electrode assembly (MEA) which employed the sulfonated copolymer with 35 mol % of disulfonated comonomer as the proton exchange membrane had approximately 2-fold lower methanol crossover and slightly higher (about 10%) cell resistance than the MEA using the perfluorosulfonic acid Nafion membrane, resulting in an approximately 50% improvement in selectivity, regardless of membrane thickness. Accordingly, this MEA outperformed the Nafion MEA control in a DMFC single-cell test. For example, 200 mA/cm2 was obtained (compared with 150 mA/cm2 for the Nafion MEA) at 0.5 V at a temperature of 80°C and ambient air pressure. Similar experiments performed with nonfluorine-containing biphenol-based sulfonated poly(arylene ether sulfone) copolymers (BPSH) indicated that the compatibility of the polymer electrolyte with the electrodes likely has a critical role in initial DMFC performance. © 2004 The Electrochemical Society. All rights reserved.
A2157
Erik Birgersson, Joakim Nordlund, Michael Vynnycky, Cyril Picard and Göran Lindbergh
An isothermal two-phase ternary mixture model that takes into account conservation of momentum, mass, and species in the anode of a direct methanol fuel cell (DMFC) is presented and analyzed. The slenderness of the anode allows a considerable reduction of the mathematical formulation, without sacrificing the essential physics. The reduced model is then verified and validated against data obtained from an experimental DMFC outfitted with a transparent end plate. Good agreement is achieved. The effect of mass-transfer resistances in the flow field and porous backing are highlighted. The presence of a gas phase is shown to improve the mass transfer of methanol at higher temperatures (>30°C). It is also found that at a temperature of around 30°C, a one-phase model predicts the same current density distribution as a more sophisticated two-phase model. Analysis of the results from the two-phase model, in combination with the experiments, results in a suggestion for an optimal flow field for the liquid-fed DMFC. © 2004 The Electrochemical Society. All rights reserved.
A2173
J. Zhou and P. H. L. Notten
An in situ method to prepare lithium microreference electrodes has been developed. The microreference electrodes are made by electrochemical deposition of metallic lithium from both the positive and negative electrodes onto a copper wire positioned in-between the two Li-based battery electrodes. The stability of these microreference electrodes was found to be dependent on the deposition current density and the thickness of the metallic lithium layer. A current density of 0.2 mA/cm2 and a lithium layer thickness of 4 μm were shown to be the most favorable deposition condition. When the potential of the electrodes eventually starts to degrade due to “consumption” of the deposit, the microreference electrodes can advantageously be recovered by lithium redeposition. The redeposited electrodes were verified to be as stable as the freshly prepared electrodes. The validity of the microreference electrode was confirmed by electrochemical impedance spectroscopy. The microreference electrodes were employed to monitor the electrode potentials during prolonged cycling. The as-obtained potential plots of both the positive and negative electrodes are present in this paper. © 2004 The Electrochemical Society. All rights reserved.
A2180
The following article is Free article
Akira Yoshino, Toshio Tsubata, Michiko Shimoyamada, Hisashi Satake, Yukiko Okano, Shiro Mori and Shizukuni Yata
We have developed a device using a novel composite material as the negative electrode and ordinary activated carbon as the positive electrode. The composite material was obtained by heat-treatment of activated carbon with pitch. The structure of this composite was shown to be amorphous based on the X-ray diffraction pattern, and the surface area decreased from 2200 m2/g (activated carbon) to 250 m2/g (composite). This device can discharge at an extremely high current density of 10,000 mA/g based on the composite weight. The power density of around 2.2 kW/L was two times higher than EDLCs, and the energy density of around 20 Wh/L was three times higher. The discharge capacity maintained its initial capacity for at least 100,000 cycles. This device also had excellent storage characteristics at 60°C. © 2004 The Electrochemical Society. All rights reserved.
A2183
Xin Wang, Mahesh Waje and Yushan Yan
Methanol-tolerant cathodic catalysts were successfully prepared by depositing platinum nanoparticles on heat-treated FeTPP/C [FeTPP stands for 5,10,15,20-tetraphenyl-21H,23H porphine iron(III) chloride] and subsequently sintering the formed catalysts. Different sintering temperatures were investigated to determine its effect on methanol tolerance. Oxygen reduction with/without the presence of methanol on these new catalysts, Pt/C and FeTPP/C, was evaluated by means of potentiodynamic measurement in a rotating disk electrode system. Complete suppression of methanol oxidation while still maintaining high activity towards oxygen reduction was realized on the catalyst sintered at 700°C. Kinetics analysis shows that oxygen reduction on this new catalyst still follows a first-order reaction and has a similar mechanism as that on the pure Pt electrocatalyst. © 2004 The Electrochemical Society. All rights reserved.
A2189
Xiaodong Wu, Zhaoxiang Wang, Liquan Chen and Xuejie Huang
Oxide-modified hard carbon was prepared by adding boron acid in the precursor using the wet chemical method. The modification effect on the electrochemical performance of the hard carbon is then evaluated. It is found that the capacity of the hard carbon can be enhanced by more than 50% of the original sample cycling between 0.0 and 3.0 V after 10.52 wt % O is introduced. This enhancement originates from the up-shift effect of the insertion potential during the discharge process. The modification of the electron structure of the host material by oxide in the carbon matrix is supposed to be responsible for the enhanced lithium storage capacity. © 2004 The Electrochemical Society. All rights reserved.
A2193
Jean-Paul Diard, Nicolas Glandut, Bernard Le Gorrec and Claude Montella
The impedance of each cell of a 10 W PEMFC stack under conditions of natural running is determined independently of the others. No electronic load is used during the experiments, even if the current flowing through the stack is greater than the current range of our electrochemical apparatus. Only a power resistor is needed, which is simpler and cheaper to use. It is shown that cell by cell, a gas starvation occurs in the stack when
and
circulate in cocurrent, the impedance increasing from the cell which is on the gas inlet-side to the cell which is on the gas outlet-side. It is also shown that the part of the internal resistance of a cell which is due to the polymer membrane is ∼40%. The method proposed in this paper can be applied whatever the number of cells in the stack, and could be useful in order to detect a failure due to only one cell, whereas the others run well. © 2004 The Electrochemical Society. All rights reserved.
CORROSION, PASSIVATION, AND ANODIC FILMS
B621
D. Bengtsson Blücher, J.-E. Svensson, L.-G. Johansson, M. Rohwerder and M. Stratmann
Scanning Kelvin probe force microscopy (SKPFM) is used to study the initial stages of atmospheric corrosion of an AlMg alloy and of physical vapor deposition (PVD) deposited 2 μm Al dots on pure Mg. The latter system is used as a model of a two-phase AlMg alloy. The influence of
was studied in situ in humid air using SKPFM. This method allows for the in situ investigation of the evolution of the Volta potential during exposure, the resolution being in the submicrometer range. The temperature was 22.0°C, and the relative humidity was 85 or 95%. The concentration of
was <1 or 350 ppm. The corrosion products were analyzed by gravimetry, ion chromatography, X-ray diffraction, scanning electron microscopy, scanning Kelvin probe, and Auger electron spectroscopy. We found that the initial stages of atmospheric corrosion on magnesium are influenced by the presence of cathodic PVD-deposited aluminum. A similar effect was seen in the case of AZ91D, the aluminum-rich β-phase forming the cathodic areas. The β-phase is nobler compared to the substrate because of the higher Al content. In the absence of
the corrosion attack is localized in nature whereas the presence of ambient levels of
results in a more general corrosion attack. The inhibitive effect of
on the atmospheric corrosion of AZ91D is explained by the formation of a passivating layer of
In the absence of
the increase in pH originating from the cathodic reaction results in the dissolution of aluminum in the passive layer. A corrosion mechanism is proposed explaining the behavior in the two environments. © 2004 The Electrochemical Society. All rights reserved.
B627
I. S. Cole, W. D. Ganther, J. D. Sinclair, D. Lau and D. A. Paterson
This paper explores the simple principle that a metal surface wets when the surface relative humidity (RH) exceeds the deliquescent RH (DRH) of any salts on the surface. Data from field exposures across 19 sites in China, the Philippines, Indonesia, and Australia is used to determine the conditions under which openly exposed surfaces wet. At each site, surface temperature (of a zinc plate), ambient RH, sensor wetness, airborne salinity, and gaseous
and
were determined over a one-year period. In conjunction with these microclimate measures, the chemistry of airborne and deposited aerosols, as well as rainwater, were measured. Complimentary data from an environmental scanning electron microscope are presented in which salts derived from the evaporation of sea salt are rewetted. Using all of this data, an assessment of the probable contaminants controlling sensor wetting at each site is made. It is found that sites with similar International Standard Organization, (ISO) 9223, classifications in terms of industrial and marine airborne pollutants show similar surface contaminants and wetting characteristics. It is proposed that dominant contaminates can be identified for each ISO classification that are consistent with the general principle that wetting occurs when surface RH exceeds the DRH of the salts making up the contaminates. These salts can change from day to day due to the continual change in the composition of the contaminates and the ongoing homogenization of previously deposited salts through chemical reaction between salts and with the surface. Rain events usually clean the surface and start the cycle over again. The application of these findings to process models of corrosion is discussed, while generalized rules for predicting surface wetting based on climate data are proposed. It is found that these generalized rules predict total time of wetness to a high degree of accuracy. © 2004 The Electrochemical Society. All rights reserved.
B636
D. Ernur, V. Terzieva, W. Wu, S. H. Brongersma and K. Maex
The influences of Cu line width and pattern density are considered as the physical factors affecting corrosion of Cu damascene interconnects. The Cu etch rate data reveals a line width dependency, for both isolated and semidense Cu lines, by showing higher etch rates for decreasing line width
in an inorganic acid-based model chemical mechanical planarization (CMP) solution. This is related to the Cu grain boundaries, which are shown to be higher in number in the narrow lines and are preferential sites for chemical attack. The absence of such a line width dependency in an organic acid-based solution signifies the importance of the interactions between Cu and CMP slurry chemicals. The Cu grain size and grain boundary volume, both as a function of line width and pattern density, are shown to be a function of the Cu electroplating bath chemistry and the plating recipe, as revealed by the microstructural data. Consequently, the lines with smaller grains are etched faster in an inorganic acid solution but not in an organic one. Therefore, by enhancing grain growth in narrow trenches and by tailoring the Cu-slurry interactions, narrow trench corrosion during CMP need not be such a challenge in future processing technologies. © 2004 The Electrochemical Society. All rights reserved.
B644
Jie He, Dennis E. Tallman and Gordon P. Bierwagen
The influence of electrodeposited polypyrrole (Ppy) films on the corrosion behavior of aluminum and Al 2024-T3 alloy, particularly on the corrosion behavior of exposed metal in damaged areas of the film, has been investigated using the scanning vibrating electrode technique (SVET). Two types of experiments are described. In one type, the Ppy was electrodeposited directly on the metal, a defect through the Ppy coating to the metal surface was introduced, and SVET measurements were made in and around the defect area. In the other type of experiment, the Ppy coating was electrodeposited on indium-tin oxide (ITO) conducting glass and electrical connection to the metal substrate was made through a switch. The SVET was then applied to map the current density distribution on both the Ppy-coated ITO and on the metal substrate when the switch was either closed or open. Both types of experiments demonstrate that the Ppy alters the corrosion behavior of the metal substrate, with dissolved oxygen playing a significant role. We also present data on the influence of oxygen on the open-circuit potential of the Ppy films and on the discharge behavior of such films. The implications of these results are discussed. © 2004 The Electrochemical Society. All rights reserved.
B652
C.-O. A. Olsson, M.-G. Vergé and D. Landolt
A comparative study of anodic film growth on niobium, zirconium, and tungsten in
was performed using the rotating electrochemical quartz crystal microbalance (EQCM). Potential sweep as well as potential step and hold experiments were performed in the range between open circuit and 8
Significant differences in the mass transients between the three metals were observed. During the formation of anodic films on niobium and zirconium, the dissolution was negligible and the fraction of the current serving for film growth was always close to unity. On tungsten, anodic dissolution in combination with film growth led to a growth fraction that diminished with time. The results obtained by the double potential step technique were compared with numerical simulations based on models considering either high field conduction or an interface reaction as limiting the kinetics of film growth. The growth of anodic films on niobium and zirconium was found limited by high field conduction, whereas film growth on tungsten was interface controlled. Film growth on tungsten was accompanied by important anodic dissolution, while dissolution of niobium and zirconium was negligible. © 2004 The Electrochemical Society. All rights reserved.
B661
R. Podor, C. Rapin, N. David and S. Mathieu
The kinetics and mechanisms of corrosion of pure tantalum in three molten glasses are investigated in the 1200-1400°C temperature range by thickness loss measurements. The corrosion layers formed at the metal/glass interface, the elemental concentration profiles in the glass, and the corrosion rates are determined. Corrosion rates are reported on an Arrhenius representation for each glass. They yield to the determination of the activation energies of corrosion processes that depend on the glass composition. The limiting process is probably the diffusion of oxygen through one of the corrosion layers. The corrosion mechanisms are described in the form of successive redox reactions between the glass and the substrate. The
standard potential is estimated to be below −1.200 V. The formation of an intermetallic compound containing boron (TaB) as a corrosion layer is evidenced for the first time. © 2004 The Electrochemical Society. All rights reserved.
B669
Zhenguo Yang, Matthew S. Walker, Prabhakar Singh, Jeffry W. Stevenson and Truls Norby
The oxidation of ferritic stainless steels has been studied under solid oxide fuel cell (SOFC) interconnect “dual” exposure conditions, i.e., simultaneous exposure to air on one side of the sample, and moist hydrogen as the fuel on the other side. The scales grown on the air side under these dual exposure SOFC conditions can be significantly different from scales grown on samples exposed to air on both sides. In contrast, no substantial difference was observed between scales grown on the fuel side of the dual atmosphere samples and scales grown on samples exposed to moist hydrogen on both sides. The anomalous oxidation of stainless steels at the air side depends on both alloy composition and thermal history. AISI430, with 17% Cr, suffered localized attack via formation of
hematite-rich nodules on the air side of dual exposure samples, while the spinel top layer of the air side scale of Crofer22 APU (23% Cr) was enriched in iron. For E-brite, with the highest Cr content (27%), no unusual phases were found in the scale on the air side, but the air side scale was less dense and appeared to be more prone to defects than the scale grown in air only. Increasing temperature and thermal cycling both accelerated the anomalous oxidation, which appeared to be related to the transport of hydrogen through the steel and its subsequent presence in the air side scale. © 2004 The Electrochemical Society. All rights reserved.
B679
M. Kendig and C. Yan
To gain a better understanding of the mechanism of corrosion inhibition by oxygen reduction reaction (ORR) inhibitors, the concentration dependence of ORR inhibition has been determined for hexavalent chromium, cerrous ion, and 2,5-dimercapto-1,3,4-thiadiazolate on a Cu rotating disk cathode. The results show critical concentrations for the respective inhibitors and suggest mechanistic differences. Hexavalent chromium inhibits ORR at concentrations as low as 1 μM. The thiazolate is chemisorbed, which contrasts with the Ce(III) which forms an inhibiting film via a precipitation on the cathode. © 2004 The Electrochemical Society. All rights reserved.
ELECTROCHEMICAL/CHEMICAL DEPOSITION AND ETCHING
C753
Oh-Kyum Kwon, Se-Hun Kwon, Hyoung-Sang Park and Sang-Won Kang
C757
T. C. Xenidou, A. G. Boudouvis, D. M. Tsamakis and N. C. Markatos
The design of a chemical vapor deposition (CVD) process in a complex reactor configuration was performed by combining computational fluid dynamics (CFD) simulations and experiments. This design methodology was implemented in a horizontal cold-wall reactor, where tin oxide deposition on silicon substrates at atmospheric pressure (APCVD) was experimentally investigated. A set of measured growth rates at different operating conditions was used to determine a Langmuir-Hinshelwood mechanism of the growth kinetics of tin oxide films by tin tetrachloride oxidation in a single-wafer reactor. The coupled kinetic/CFD model was then used to further analyze the influence of some key operating parameters on the process performance. Simulation results are suggestive of modifications in the operating parameters that could enhance the uniformity of the layer thickness. In particular, the uniformity of the layer thickness was investigated, with special attention paid to the origins of the axial and transverse heterogeneities on the wafer for each of the parameters examined, thus opening possible ways of process improvement. © 2004 The Electrochemical Society. All rights reserved.
C765
Bülent M. Bas¸ol
Electrochemical mechanical deposition (ECMD) is a new technique that has the ability to deposit planar copper films on nonplanar substrate surfaces. This technique involves electrochemical deposition and simultaneous sweeping of the substrate surface with a planarization pad. In this study we show that planarization of low-aspect-ratio features on a wafer surface by ECMD is due to a newly identified “mechanically induced superfilling” phenomenon. Sweeping of the top surface of the wafer at preset intervals establishes a transient differential in the surface coverage of organic additives at the top surface and the cavity regions, preferentially increasing the current flow into the cavities. Planarization decreases as the time interval between sweeps increases. Increase in the deposition rate of copper into the low-aspect-ratio features results in an associated decrease of deposition onto the top surface under galvanostatic conditions. A model that invokes surface coverage transients of accelerator species is offered to explain the experimental results. © 2004 The Electrochemical Society. All rights reserved.
C772
S. Vicknesh and A. Ramam
A systematic study of the etching of InP material by hydrogen bromide (HBr)-based chemistry is conducted using the inductively coupled plasma (ICP) technique. Sidewall profiles, material selectivity, surface morphologies, and the residual species due to the chemistry are observed as functions of varying process parameters like ICP power, reactive ion etching (RIE) power and pressure. The highest selectivity of InP:PR of 4.2 is achieved at an ICP power of 100 W for a constant set of RIE power, pressure, HBr flow rate, and temperature parameters. Sidewall striations on etched faces have been eliminated by optimizing baking parameters on the photoresist pattern prior to etching. A characteristic kink effect phenomenon is observed with the introduction of argon in HBr chemistry to which is attributed the fluctuation of the chamber pressure. X-ray photoelectron spectroscopy results indicate the strong presence of
which is believed to affect the formation of anisotropic sidewalls at room temperature. © 2004 The Electrochemical Society. All rights reserved.
C781
Zenglin Wang, Osamu Yaegashi, Hiroyuki Sakaue, Takayuki Takahagi and Shoso Shingubara
The bottom-up fill of copper in fine via holes is reported in electroless copper plating with the addition of bis(3-sulfopropyl) disulfide (SPS). When the concentration of SPS in the plating bath was varied from 0.05 to 0.5 mg/L with a plating time of 10 min, the ratio of the Cu thickness at the bottom of the hole
to that at the surface
called the bottom-up ratio, increased from 1.05 to 2.8 for a ⊘ 1.0 μm hole. The bottom-up ratio increases with SPS concentration and decreases with an increase in hole diameter. X-ray diffraction structure analyses and cross-sectional transmission electron microscopy observations indicated that the grain size of Cu film was reduced by the SPS addition, but Cu(111) texture was enhanced by the SPS addition. Bottom-up fill may be attributed to a higher SPS concentration at the surface than at the bottom of the holes due to SPS incorporation in the Cu film and diffusion-limited flux of SPS molecules into fine holes. © 2004 The Electrochemical Society. All rights reserved.
C786
Byoung-Yong Chang and Su-Moon Park
C789
Liudmila Larina, Ki Hwan Kim, Kyung Hoon Yoon, Makoto Konagai and Byung Tae Ahn
C793
Marc Petri, Dieter M. Kolb, Ulrich Memmert and Heinrich Meyer
The adsorption of polyethylene glycol (PEG) on Au(111) for three different molar masses was studied by cyclic voltammetry, capacity measurements, and in situ scanning tunneling microscopy for the first time. New physical insight into the adsorption behavior of this polymer on a solid electrode in neutral
was gained. The formation of a condensed phase has been observed, the stability range depending strongly on the chain length and the concentration of PEG. Because of their importance in electroplating the influence of chloride ions on the PEG adsorption behavior has also been investigated, together with the effect of PEG and chloride on the initial stages of Cu deposition. Addition of chloride does not lead to an increased adsorption of PEG as found for other surfaces (e.g., copper), but to a simple superposition of both adsorption processes. However, a strong inhibition for copper bulk deposition is observed when both additives are present in solution. © 2004 The Electrochemical Society. All rights reserved.
C798
Kuniaki Murase, Mitsuyasu Ogawa, Tetsuji Hirato and Yasuhiro Awakura
The electrodeposition of Ni-Mo alloy using a series of aqueous acidic citrate plating baths (pH 5.0) were examined from the standpoint of the Ni(II)- and Mo(VI)-species present in the solutions. The distribution of the species was calculated using a set of the formation constants for polymolybdates and citrate complexes, optimized by a factor analysis of optical spectra. Through the design of the bath compositions such that the dominant Ni(II)- and Mo(VI)-species are both 1:1 complexes with citrate, lustrous and uniform Ni-Mo layers having almost constant Ni content were found to be plated over a wide range of Ni(II)/Mo(VI) analytical concentration ratios, although the current efficiency decreased with decreasing Ni(II) concentration. This indicates the validity and importance of the bath design using these constants. The deposition phenomena were briefly discussed in terms of the mechanisms hitherto reported. © 2004 The Electrochemical Society. All rights reserved.
C806
Toshihiro Nakamura, Takuro Nishimura and Kunihide Tachibana
C811
Fan-Yin Su, Jing-Fang Huang and I-Wen Sun
The electrodeposition of palladium-gold alloy was investigated in an ambient temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium chloride tetrafluoroborate system
containing palladium(II) and gold(I). Compact alloy deposits were obtained with galvanostatic electrolysis. The Pd content in the deposited Pd-Au alloy increases with increasing current density and the Pd mole fraction in the plating bath. For deposits obtained under mass-transport-limited current, the Pd content in the deposited alloys approximated the Pd mole fraction in the plating bath. The deposition temperature affected the homogeneity of the deposited Pd-Au solid solution. Data collected from X-ray powder diffraction experiments showed that Pd-Au alloys deposited at temperatures higher than 80°C were homogeneous Pd-Au solid solutions. The scanning electron micrographs of the deposits revealed nodular particles. The particle size decreased with increasing deposition current. © 2004 The Electrochemical Society. All rights reserved.
C816
Sam Siau, Alfons Vervaet, Sylvie Nalines, Etienne Schacht and Andre Van Calster
The adhesion of plated metal layers to epoxy polymer surfaces is of prime importance for the reliability of electronic interconnections. An increase in the roughness of the polymer surface, caused by chemical treatment, strengthens adhesion by increasing the total area of interaction between both layers. The evolution of the roughness at the polymer surface is studied through the kinetics of the chemical reactions on the surface. Sweller agents, that are able to diffuse through the free volume of the polymer, react with polar groups present in the bulk of the polymer and form channels. An increase in polar groups at the surface and the formation of channels facilitates the transport of water through the free volume of the polymer. The polar groups in these patches react with oxidizers and cause the formation of cavities as reported in literature. A mathematical model is developed to explain the influence of swellers and oxidizing agents on the development of polymer surface roughness. This model is based on atomic force microscopy measurements for the roughness and on attenuated total reflectance-infrared and electron spectroscopy for chemical analysis for the chemical changes on the polymer surface. Mass measurements are also used to record mass changes. The proposed model permits the prediction of roughness evolution. © 2004 The Electrochemical Society. All rights reserved.
C831
Sam Siau, Alfons Vervaet, Sylvie Nalines, Etienne Schacht and Andre Van Calster
The adhesion of plated metal layers to epoxy polymer surfaces is of prime importance for the reliability of interconnections in microelectronics. An increase in the roughness of the polymer surface, caused by chemical treatment, plays an important part in the adhesion strength of plated metal layers by increasing the total area of interaction between both layers. This kinetic study of the influence of chemical treatments on the surface of the polymer consists of two parts. In Part I the kinetics of sweller treatments and of the solvent were examined in detail and a kinetic model for the influence of sweller and solvent was developed. In this second part the kinetics of the formation of roughness at the polymer surface due to oxidative liquid treatments is examined. A kinetic model is developed based on experimental studies, compromising the combined effects of sweller-oxidizer treatments and the influence of diffusion of the different components. A number of examples are given and verified by experiment. The roughness of the treated polymer samples is measured experimentally by atomic force microscopy. Time-dependant mass measurements were used to record mass changes due to diffusion and reaction. © 2004 The Electrochemical Society. All rights reserved.
C850
Soo-Jung Kim, Hyun-Tae Kim and Su-Moon Park
Effects of o-vanillin on electrodeposition of zinc on iron electrodes have been studied employing transient electrochemical, electrochemical quartz crystal microbalance, spectroelectrochemical, and surface analytical techniques. The results indicate that o-vanillin is adsorbed strongly on the iron surface, raising overpotentials for hydrogen evolution as well as for zinc deposition. o-Vanillin shows greater effects on the earlier stage of the zinc electrodeposition in the underpotential region than in the bulk deposition region. The additive appears to adsorb preferentially on the top of the dendritic growth sites, leading to a leveling effect. The zinc layer obtained in the presence of o-vanillin shows smoother morphology with smaller grain sizes and higher specular reflectance signals. Reflectance spectroelectrochemistry has been used for the first time to monitor the brightness of the electroplated surface. © 2004 The Electrochemical Society. All rights reserved.
ELECTROCHEMICAL SYNTHESIS AND ENGINEERING
D113
John M. Kinyanjui, Justin Hanks, David W. Hatchett, Anthony Smith and Mira Josowicz
D121
F. Lantelme and H. Groult
During the electrolysis of fused KF-2HF strongly adherent bubbles of fluorine gas appear at the surface of the carbon anode. It was observed that the current is passing even when the anode was fully covered with a gas film. Impedance measurements performed in KF-2HF coupled with visual observations with a see-through cell show the existence of a conducting layer beneath the gas film. Experiments were performed to study the bubble growth by transient techniques. The results were interpreted in the frame of a model which shows the predominant role of the interfacial properties. A new approach, introducing capillary forces, leads to the concept of a variable curvature radius at the gas-liquid interface which is in agreement with the observed bubble shape. Digital simulation is used to describe the bubble growth and to calculate the values of interfacial parameters. © 2004 The Electrochemical Society. All rights reserved.
D127
Chi-Min Lin and Shiow-Kang Yen
The cathodic reactions of electrolytic nanocrystalline
coating on pure titanium were investigated by polarization tests in
alcoholic and HCl aqueous solutions, respectively. Three major reactions which belong to various applied voltage ranges were identified: (i)
from −0.1 to −0.3 V (Ag/AgCl), 
from −0.3 to −0.9 V, and 
from −0.9 to −2.5 V. Excellent deposition was located at the third stage, because
ions were depleted and many more
ions were provided to form
on the cathodic surface. The coated films were further characterized by thermogravimetric differential thermal analysis, X-ray diffraction, X-ray photoelectron spectrometer, scanning electron microscopy, atomic force microscopy, dynamic cyclic polarization, and cell bioactivity assay. After being annealed at 300°C for 1 h, the coated films were further condensed into anatase
and gradually transformed into rutile
at 500°C. From cross section, the
coated film ∼1.2 μm thick revealed excellent adhesion with substrate. Compared with thermally grown oxide
film, much better bioactivity and more corrosion resistance were found on the electrolytic
coated specimens. © 2004 The Electrochemical Society. All rights reserved.
PHYSICAL AND ANALYTICAL ELECTROCHEMISTRY
E349
H. Yamada, W. S. Shi and C. N. Xu
The thermal degradation of
(BAM) was investigated by forcibly annealing BAM particles in air at temperatures of 500-1300°C. Rietveld analysis with powder X-ray diffraction revealed novel lattice deformations in the thermally degraded BAM. The lattice constants c and a changed monotonically as annealing temperature increased, while the unit-cell volume
showed no change with annealing up to 900°C, then abruptly expanded with 1100°C annealing. Furthermore, peak profile analysis revealed increasing lattice strain being induced in the host lattice. We suggest that the main cause of the thermal degradation of BAM is due to generation of a lattice vacancy like the Schottky defect. © 2004 The Electrochemical Society. All rights reserved.
E352
Christophe Rambaud, Laurent Cagnon, Jean-Pierre Levy and Gérard Tourillon
The sum frequency generation (SFG) characteristics of thiocyanate ions adsorbed on polycrystalline gold electrodes and on electrodeposited cobalt and nickel films are presented. The aim of this study is to compare the ion adsorption behavior on these metals by studying the CN stretching mode variations. In the cobalt-containing solution, a transition in the band frequency potential dependence between the naked gold surface and the cobalt-covered one has been evidence for potentials more positive than the one required for bulk cobalt deposition, suggesting that an anion-induced underpotential deposition process is taking place. The change of the SFG spectrum shape, the higher slope value of the band potential dependence, and the lower band frequency value observed on the bulk electrodeposited Co and Ni films suggest differences in the interaction strength, related to the d band filling of the substrate, and in the adsorption geometry of thiocyanate ions on these metals compared to the gold surface. © 2004 The Electrochemical Society. All rights reserved.
E358
Mohamed Ismail Awad, Ao Denggerile and Takeo Ohsaka
The kinetics of electroreduction of peroxyacetic acid (PAA) has been studied at a gold electrode in acetate buffer solutions of pH in the range 3-6. The electroreduction of PAA was irreversible. The relevant kinetic parameters including the Tafel slope, the standard rate constant
the electrochemical reaction order (m), the product
of the transfer coefficient and the number of electrons involved in the rate-determining step, and the number (n) of electrons involved in the overall electrode reaction were determined using cyclic voltammetry, hydrodynamic voltammetry, and hydrodynamic chronocoulometry. The Tafel
V/decade, 
cm s−1,
and
The formal potential of the PAA/acetic acid redox couple was also theoretically calculated to be 1.762 V vs. Ag/AgCl based on the equilibrium constant for the reaction of PAA and hydrogen peroxide
in the presence of acid catalyst and the standard redox potential of
The diffusion coefficient of PAA was also estimated. Based on the obtained results, the overall electroreduction of PAA is considered to be composed of two one-electron reduction steps with the formation of acetate or hydroxyl radical as probable reaction intermediates. © 2004 The Electrochemical Society. All rights reserved.
E364
Mya Norman, Richard D. Noble and Carl A. Koval
Electrolysis of (dimethylformamide) (DMF) solutions containing tetraalkylammonium iodide salts and dissolved iodine in a two-compartment cell separated by a Nafion membrane results in transfer of solution volume between the two compartments. The pumping process was reversible and the rate, which ranged from 20 to 50 μL/min, was controlled by the cell current. The volume of solution pumped was significantly greater than what is predicted from the apparent molar volumes of the species involved in the electrolysis and from the charge passed. The additional volume is attributed to migration-assisted solvent flow across the membrane separator. Comparison of pumping results for a series of Nafion materials indicated that the solvent flow was related to the number of solvent molecules per ion-exchange site in the membrane. Pumping occurred with and against small external pressures up to 0.1 atm. Analysis of apparent molar ionic volumes indicates that the electrode reaction,
contributes little to the observed volume change. Instead, the pumping is associated almost entirely with the apparent molar ionic volume of tetraalkylammonium ions and migration-assisted flow of DMF. © 2004 The Electrochemical Society. All rights reserved.
DIELECTRIC SCIENCE AND MATERIALS
F283
C. Cabral Jr., C. Lavoie, A. S. Ozcan, R. S. Amos, V. Narayanan, E. P. Gusev, J. L. Jordan-Sweet and J. M. E. Harper
We present an evaluation of the thermal stability for various elemental metals and binary/ternary conducting compounds on gate dielectrics. The continued scaling of polysilicon gated complementary metal oxide semiconductor (CMOS) devices may face limitations such as polydepletion, incompatibility with some high-k dielectrics, high series resistance, and boron penetration. In this study, 24 different elemental metals and metallic compounds with work functions ranging from 4.0 to 5.2 eV covering n-type field effect transistor (nFET), midgap, and pFET gate electrodes were examined. The films were characterized during rapid thermal annealing in a forming gas ambient up to 1000°C. Three techniques, in situ X-ray diffraction, resistance, and elastic light scattering analysis were used simultaneously during annealing. It was found that many of the elemental materials, especially those with nFET work functions, undergo reactions with the
and
gate dielectrics, while others became unstable because of melting (Al) or agglomeration (Co, Ni, Pd and
Two binary compounds,
and
underwent dissociation in the hydrogen-containing ambient. Materials stable above 700°C include Mo, W, Re, Ru, Co, Rh, Ir, Pd, Pt,
TaN, TaSiN, and
making them possible choices for integration involving higher temperature processing. © 2004 The Electrochemical Society. All rights reserved.
F288
M. Houssa, S. De Gendt, G. Groeseneken and M. M. Heyns
SEMICONDUCTOR DEVICES, MATERIALS, AND PROCESSING
G801
Yoshitaka Nakano, Osamu Fujishima, Tetsu Kachi, Koji Abe, Osamu Eryu, Kenshiro Nakashima and Takashi Jimbo
G805
T.-C. Chang, S. T. Yan, P. T. Liu, C. W. Chen, H. H. Wu and S. M. Sze
In this work, a novel concept of quasi-superlattice storage (QS2) is demonstrated. Under a suitable operating voltage, two apparent states of charge storage can be distinguished. The memory effects are due to the multilevel charge storage within the quasi-superlattice. The multilevel charge storage provides a feasible design for the 2-bit-per-cell nonvolatile memory devices. Also, the leakage behavior of the quasi-superlattice structure has also been characterized by current-voltage measurements at room temperature and low temperatures. The resonant tunneling-like leakage characteristic is observed at low temperatures. A concise physical model is proposed to characterize the leakage mechanism of tunneling for the quasi-superlattice structure, and this suggests that consideration of the operating voltage for the 2-bit-per-cell nonvolatile memory device needs to be taken into account. © 2004 The Electrochemical Society. All rights reserved.
G809
Len Borucki, Leslie Charns and Ara Philipossian
A detailed model is described for the generation, transport, and exchange of thermal energy in rotary chemical mechanical polishing (CMP) tools. Frictional energy generated due to abrasion of the wafer by the pad and slurry particles is partitioned between the pad and the rotating wafer, with the majority going to the latter. The slurry at the same time provides a major cooling mechanism, drawing heat away while it is entrained under the wafer and then redistributing it over the pad by radial convection. The slurry flow component of the theory includes thermal effects due the presence of concentric grooves. The model accounts for the time and radial dependence of pad temperature measurements performed on flat and concentrically grooved pads at the leading and trailing edges of the wafer, at the pad center and pad margins, and on the wafer carrier. It suggests that the temperature increase on the wafer may be approximately twice the increase measured on the pad. © 2004 The Electrochemical Society. All rights reserved.
G814
Hitoshi Habuka, Shinji Kobayashi, Masayuki Kato, Takashi Takeuchi and Masahiko Aihara
Water flow in an overflow rinse bath of the carrierless wet station for cleaning silicon wafers of 300 mm diam was studied, from the view point of the transport phenomena. Both the experiment of flow visualization and the numerical calculation using the transport equations show that the direction and the velocity distribution of the water from the water nozzle can be optimized by adjusting the wall thickness of the water nozzle. Additionally, this direction is shown to influence the water motion in the entire rinse bath and that between the wafers. Theoretical calculations taking the entire geometry and the detail of the water nozzle into account are shown to be applicable to predict and design the water flow in the wet cleaning bath. © 2004 The Electrochemical Society. All rights reserved.
G819
Sum Huan Ng, Inho Yoon, C. Fred Higgs III and Steven Danyluk
Wafer curvature, contact pressure, and film stresses have been a subject of interest to many researchers who are working on the modeling of within-wafer nonuniformity in chemical mechanical polishing (CMP). Wafer shape and film stresses prior to and after CMP have been measured before in order to correlate film stresses with removal rate distribution across the wafer. In this paper we describe measurements of wafer bending under static loading and in dynamic conditions. A finite element analysis is also carried out to model wafer bending under static loading. © 2004 The Electrochemical Society. All rights reserved.
G824
Asuha, Yueh-Ling Liu, Osamu Maida, Masao Takahashi and Hikaru Kobayashi
We have succeeded in the fabrication of Si-based metal-oxide-semiconductor diodes with an ultrathin (i.e., ∼1.4 nm thick) silicon dioxide
layer whose leakage current density is lower than those for thermally grown
layers with the same thickness. The leakage current density of the as-grown
layers formed in concentrated nitric acid
solutions (i.e., ∼3 A/cm2 at the forward gate bias,
of 1 V) is as high as those for thermal
layers. The leakage current density is decreased to ∼1.5 and ∼1 A/cm2 at
V by postoxidation annealing (POA) at 400 and 500°C (in hydrogen), respectively, and the decreases are mainly attributed to the elimination of interface states and slow states, respectively. The vibrational frequency of longitudinal optical (LO) phonons of Si-O asymmetric stretching vibration increases with the POA temperature, while that of the transverse optical (TO) phonons remains constant. From the analysis of these vibrational frequencies, the atomic density of the as-grown
layer and that after POA at 500°C are estimated to be 2.34 and
cm3, respectively, i.e., higher than that of crystalline
bulk of
cm3. Measurements of the valence band spectra for the
structure show that the valence band discontinuity energy at the
interface is increased from 4.3 to 4.6 eV by POA at 500°C. Therefore, the other reason for the decrease in the leakage current density by POA is a reduction in the tunneling probability through
caused by the increase in the band discontinuity energy. Postmetallization annealing treatment at 200°C in hydrogen performed after POA further decreases the leakage current density, showing that atomic hydrogen passivates defect states more effectively than molecular hydrogen. © 2004 The Electrochemical Society. All rights reserved.
G829
M. K. Lee, C. M. Shih, S. Y. Lin, C. D. Yang and T. H. Shih
Using an aqueous solution of hydrosilicofluoric acid, boric acid, and ammonium hydroxide, fluorine-doped oxynitride films can be deposited on a silicon substrate. The fluorine and nitrogen atoms are piled up at about 160 Å from the interface. The electrical characteristics were improved by decreasing the film thickness toward 160 Å due to the increase of fluorine and nitrogen concentrations. The electrical characteristics were degraded by further decreasing the film thickness from 160 to 110 Å due to the interfacial nonstoichiometric oxide. The quality of fluorine-doped oxynitride films with a prepared thickness thinner than 160 Å can be improved under photoillumination. Thus higher nitrogen and fluorine concentrations of the films can be obtained by photoillumination. © 2004 The Electrochemical Society. All rights reserved.
G833
Igor Levin, Mark Kovler, Yakov Roizin, Menachem Vofsi, Richard D. Leapman, Gary Goodman, Norio Kawada and Munabu Funahashi
G839
Markus Forsberg, Ted Johansson, Wei Liu and Manoj Vellaikal
A shallow and deep trench isolation process module for high performance rf bipolar complementary metal-oxide-semiconductor (BiCMOS) is presented in detail. The shallow trench is etched prior to the deep trench, allowing the deep trench to be placed self-aligned to the shallow trench edge. By planarizing the polycrystalline silicon deep trench filling using chemical mechanical polishing (CMP) before etchback, the recess into deep trenches is decreased and polysilicon spacer formation at the active area edges is avoided. The poly CMP is stopped before all polysilicon in the active area is removed, to avoid polysilicon dishing and erosion of oxide on top of nitride on active area. Important issues arising during process development are discussed. Two different slurries were evaluated, which resulted in two different nonuniformities of polysilicon thickness. Nonuniformity transfers partially down to a range of recesses into the deep trenches, but the recesses were much smaller compared to the etchback only. High-density chemical vapor deposition was used for shallow trench filling and a direct shallow trench isolation-CMP process was developed. The feasibility of the process module was demonstrated using a 0.25 μm, 200 mm bipolar double-poly rf process with optional SiGe epi base. Electrical results from completed transistors are presented to verify the function of the module. © 2004 The Electrochemical Society. All rights reserved.
G847
Maria Ronay
It was shown by parallel plate rheological experiments that a second-order normal force develops between a polyurethane planarizing pad and a patterned silicon dioxide wafer upon sliding contact. Both torque and normal force increase with increasing down force and increasing rate of shear. From these data a linear relation was found between normal force and torque squared as required by second-order theory. The slope of the line was one in the dry condition, increased significantly upon application of an abrasive slurry, and decreased from a dishing-reducing additive. The normal force caused normal extension of the polyurethane pad into the down areas of the wafer which was estimated from elaborate polishing experiments. This extension was also reduced by a dishing-reducing additive. No normal force developed between a fixed abrasive pad, known for creating perfect planarization, and a wafer, further indicating a causal relationship between the development of normal force in the pad during chemical mechanical planarization and the dishing of the down areas of a wafer. © 2004 The Electrochemical Society. All rights reserved.
G853
Yen-Po Lin and Jenn-Gwo Hwu
G858
Hoyoun Kim, Beumyoung Park, Sangick Lee, Haedo Jeong and David A. Dornfeld
It has been known that overpolishing in chemical mechanical polishing (CMP) depends on pattern selectivity as a function of density and pitch, and use of a fixed abrasive pad is one method which can improve the pattern selectivity. This paper introduces the fixed abrasive pad using the swelling characteristic of hydrophilic polymers, which can acquire self-conditioning during CMP. When applied to tungsten blanket wafers, the fixed abrasive pad showed better pattern selectivity compared to the general polishing process, and, also, erosion was measured for ∼20 nm or less at even 100% overpolishing. © 2004 The Electrochemical Society. All rights reserved.
G863
Yu-Zung Chiou
High-performance AlGaN/GaN/AlGaN double heterojunction metal oxide semiconductor (MOS)-heterojunction field effect transistors (HFETs) with high-quality
layers deposited by photochemical vapor deposition (photo-CVD) technology were fabricated and reported. With a 1 μm gate, the maximum saturated
maximum
and gate voltage swing of the photo-CVD fabricated MOS-HFETs were 755 mA/mm, 95 mS/mm, and 8 V, respectively. Even at a high temperature of 300°C, the maximum saturated
and maximum
of the fabricated MOS-HFETs were still kept at 323 mA/mm and 41 mS/mm, respectively. Moreover, the simulation results clearly suggest that the temperature-induced degradation of saturation velocity is predominantly responsible for the degradation mechanisms of
and
© 2004 The Electrochemical Society. All rights reserved.
G866
E. Leoni, L. Martinelli, S. Binetti, G. Borionetti and S. Pizzini
The nucleation process of oxygen precipitates in silicon at 650°C was investigated using photoluminescence (PL) measurements, which are demonstrated to provide a highly sensitive tool for the characterization of precipitates differing in structure and shape. The results of this study were first analyzed from a thermodynamic and kinetic point of view in order to explain the effect of minute differences in oxygen concentration on the PL spectra, which indicates that two kinds of nanometric oxides coexist in dynamic equilibrium. Then a hypothesis is advanced about the origin of the oxygen-induced PL bands, which is explained in terms of carrier confinement effects induced by the strain at oxide precipitates. © 2004 The Electrochemical Society. All rights reserved.
G870
Z. M. Rittersma, J. J. G. P. Loo, Y. V. Ponomarev, M. A. Verheijen, M. Kaiser, F. Roozeboom, S. Van Elshocht and M. Caymax
G878
Yan Fang and Srini Raghavan
The objective of this paper was to characterize the fundamental electrochemical behavior of thin aluminum-0.5% copper/titanium stack films before, during, and after abrasion in a commercially available alumina-based slurry containing iodate as an oxidant. A research apparatus in which electrochemical tests can be carried out during polishing was fabricated and used for this research. During the abrasion of the Al/Ti film stack, a sharp rise in corrosion potential
on the order of 1000 mV, was measured. The transition was much sharper with the low-temperature (25°C) Al film than the high-temperature (475°C) Al thin film. The slower transition in open-circuit potential in high-temperature films is most likely due to a Ti-Al intermetallic compound formed at the Al/Ti interface. Additionally, the galvanic corrosion between Al and Ti during abrasion was investigated. © 2004 The Electrochemical Society. All rights reserved.
G882
N. Chandrasekaran, S. Ramarajan, W. Lee, G. M. Sabde and S. Meikle
The effects of chemical mechanical planarization (CMP) process parameters and consumables on the polish rate and defects generated in various low-k materials with k values ranging from 2.2 to 3.0 were studied in detail. The process consumables and conditions evaluated include slurry material (alumina and silica), pad type (soft and hard), polish pressure, and polish time. Atomic force microscopy (AFM) images and roughness numbers were used to evaluate the post-CMP defect generation under various process conditions and revealed nano/microscratches, pits, voids, and film delamination. For a given material, the removal rate increased with increasing pressure. The dependence of defects on pressure appeared highly driven by the slurry material, pad type, and low-k material properties. Defects increased with increasing pad hardness and decreasing k values. The increasing defects with decreasing k value can be attributed to the lower elastic modulus observed with low-k materials. Removal rates exhibited both a decrease and an increase in conjunction with polish time, depending on the type of low-k material used. AFM analysis showed an improvement in global surface roughness with increasing polish time; however, an increase in localized defects such as pits was also observed. Fourier transform infrared and X-ray photoelectron spectroscopy analyses showed no change in film chemistry under the conditions studied here. © 2004 The Electrochemical Society. All rights reserved.
G890
Deuk Yeon Lee, Seok-Kyun Song, Seok-Keun Koh, Hong-Koo Baik and Kie Moon Song
The initial growth behaviors of Au thin films on tin oxide substrates were investigated by in situ conductance measurement. The crystallinity of tin oxide films fabricated by ion-beam-assisted deposition was changed from amorphous to preferred oriented structure with ion beam energy. As the surface energy of tin oxide substrates increases with the irradiation of ion beams, an onset thickness of Au films is decreased. That means high surface energy of the substrate enhances surface mobility of Au adatoms so that it changes the growth mode of Au films from 3D to 2D growth. So the distance between islands where electron tunneling can occur is decreased with the surface energy of the substrate. Therefore, we conclude that different surface properties of tin oxide substrates play an important role in the early growth aspects of Au thin films. © 2004 The Electrochemical Society. All rights reserved.
G895
Tomonari Yamamoto, Ken-ichi Goto, Tomohiro Kubo, Yun Wang, Tim Lin, Somit Talwar, Masataka Kase and Toshihiro Sugii
In this paper, we report on the ultrashallow junction profiles and good characteristics of sub-50 nm bulk complementary metal oxide semiconductor (CMOS) devices with n+/p+ source-drain extensions (SDEs) formed by laser thermal processing (LTP). By combining LTP with preamorphization and strong-dosage dopant-ion implantation, CMOS drive current can be improved without incurring a cost in terms of short-channel deterioration. The SDE-junction depth, SDE overlap length, and sheet resistance were controlled by the energy of preamorphization implantation, and the first two of these parameters were independent of dopant dosage. This allowed us to design strongly activated and abrupt box-like dopant profiles. With this technique, we obtain improvements in drive current of 13 and 8%, respectively, for p- and n-metal oxide semiconductor field effect transistors at
and
without inducing any short-channel deterioration. © 2004 The Electrochemical Society. All rights reserved.
G900
Huang-Chung Cheng, Fang-Long Chang, Ming-Jang Lin, C. C. Tsai and C. W. Liaw
G904
R. Edrei, R. Shima, V. V. Gridin, Y. Roizin, W. D. Kaplan and A. Hoffman
The evolution of the surface topography and microstructure of silicon films deposited near the amorphous-to-polycrystalline transition was investigated, and was found to be accompanied by the appearance of crystalline aggregates whose density and size distribution strongly depend on deposition parameters. The films were deposited by low-pressure chemical vapor deposition, and the parameters varied were temperature, pressure, film thickness, and substrate material. Both temperature and pressure have a dramatic effect on the density and size of surface aggregates. A transition from amorphous to polycrystalline silicon at the critical temperature,
is evident from the abrupt change in surface roughness. This effect was far more pronounced for thin (55 nm) silicon films than for their thicker (150 nm) counterparts and was generally larger for films grown directly on c-Si rather than on SiOx substrates. Evidence for nanocrystalline silicon particles embedded into the amorphous matrix below
was found. In this study, it is suggested that the amorphous-polycrystalline silicon transition and consequently the surface topography evolution of the films is fluctuation assisted. The transition manifests itself in an enhanced population of Si nucleation centers, which are mostly formed at the upper surface of the deposited film. © 2004 The Electrochemical Society. All rights reserved.
G910
Xiao-an Fu, Christian A. Zorman and Mehran Mehregany
The surface roughness of epitaxially grown 3C-SiC films is a key factor affecting the fabrication and performance of SiC-based nanoelectromechanical systems. This paper presents the results of a study on adjusting key deposition process parameters to control surface roughness of 3C-SiC films during film growth. For 3C-SiC films grown using a conventional three-step, carbonization-based, atmospheric pressure chemical vapor deposition process, the surface roughness depends on the precursor gas flow rates during both the carbonization and film growth steps. By optimizing the carbonization and the film growth steps with respect to surface roughness, an average surface roughness of 1.5 nm for a 50 nm thick 3C-SiC film was achieved. © 2004 The Electrochemical Society. All rights reserved.
G915
N. Moser, R. C. Fitch, A. Crespo, J. K. Gillespie, G. H. Jessen, G. D. Via, B. Luo, F. Ren, B. P. Gila, C. R. Abernathy et al
SENSORS AND DISPLAYS: PRINCIPLES, MATERIALS, AND PROCESSING
H243
Kee-Sun Sohn, Byung Il Kim and Namsoo Shin
We developed an evolutionary optimization process involving a genetic algorithm and combinatorial chemistry (combi-chem), which was tailored exclusively for the development of light emitting diode (LED) phosphors with a high luminescent efficiency, when excited by soft ultraviolet irradiation. The ultimate goal of our study was to develop oxide red phosphors, which are suitable for three-band white LEDs. To accomplish this, a computational evolutionary optimization process was adopted to screen a
-doped alkali earth borosilicate system. The genetic algorithm is a well-known, very efficient heuristic optimization method and combi-chem is also a powerful tool for use in an actual experimental optimization process. Therefore the combination of a genetic algorithm and combi-chem would enhance the searching efficiency when applied to phosphor screening. Vertical simulations and an actual synthesis were carried out and promising red phosphors for three-band white LED applications were obtained. © 2004 The Electrochemical Society. All rights reserved.
H249
Shinnosuke Koji and Shinobu Fujihara
H254
A. Bessière, P. Dorenbos, C. W. E. van Eijk, E. Yamagishi, C. Hidaka and T. Takizawa
H261
Deganit Barak-Shinar, Moshe Rosenfeld and Shimon Abboud
GENERAL TOPICS
J91
Chun-Chieh Chang, Oleg I. Velikokhatnyi and Prashant N. Kumta
The total energy of lithiated and delithiated Mg-substituted lithium nickel oxide
has been calculated using the ab initio projector-augmented wave method implemented in the density functional theory code VASP. The lattice parameters and cell volumes obtained from the calculations are in general agreement with the experimental results (<2% error). By calculating the average cell voltage using the Nernst equation, it is observed that the Mg-substituted lithium nickel oxide possesses a higher average voltage during the deintercalation process, which also agrees with the observed experimental results. Further calculations on the charges of Li, Ni, Mg, and O in lithiated and delithiated
indicate that the substitution of Mg has more influence on the O charge. Because oxygen is oxidized more than Ni during the process of Li removal (oxidation process) and the substitution of Ni with Mg causes oxygen to be further oxidized, it can be concluded that the increase in the average cell voltage is more related to this further oxidation of oxygen resulting from the substitution of Mg. © 2004 The Electrochemical Society. All rights reserved.
J95
S. Bredikhin, G. Abrosimova, A. Aronin, K. Hamamoto, Y. Fujishiro, S. Katayama and M. Awano