Batteries, Fuel Cells, and Energy Conversion
A969
Venkat Srinivasan, John W. Weidner and John Newman
The nickel hydroxide electrode is known to exhibit a stable hysteresis loop, with the potential on charge being higher than that on discharge at every state-of-charge (SOC). What we show here is that this loop created during a complete charge and discharge (i.e., boundary curves) is not sufficient to define the state of the system. Rather, internal paths within the boundary curves (i.e., scanning curves) can be generated that access potentials between the boundary curves. The potential obtained at any SOC, as well as how the material charges and discharges from that point, depends on the cycling history of the material. The implication of this phenomenon is that the potential of nickel-based batteries cannot be used as an indication of the SOC of the cell. Analysis of the boundary and scanning curves suggest that the electrode consists of a number of individual units or domains, each of which exhibits two or more metastable states. The cycling behavior of the nickel hydroxide electrode is discussed within the context of previously developed theoretical arguments regarding domain theory. Although the specific cause for the metastability in each domain is not understood, considerable insights are provided into the history-dependent behavior of the nickel hydroxide electrode. Finally, an empirical procedure is developed to predict the scanning curves based on the boundary curves. © 2001 The Electrochemical Society. All rights reserved.
A981
Akihisa Kajiyama, Kazunori Takada, Taro Inada, Masaru Kouguchi, Shigeo Kondo and Mamoru Watanabe
A984
Ken Tasaki and Shinichiro Nakamura
A989
Soon-Ki Jeong, Minoru Inaba, Takeshi Abe and Zempachi Ogumi
A994
Yang-Kook Sun, Gyeong-Su Park, Yun-Sung Lee, Masaki Yoashio and Kee Suk Nahm
The structural integrity of the oxysulfide material,
before and after charge-discharge cycling at high temperature was studied by X-ray diffraction and high-resolution transmission electron microscopy. The rock salt phase
which is associated with capacity loss has been detected at the surface of the oxysulfide particles in the electrode cycled in the 4 V region at 80°C. The small structural degradation of the new oxysulfide material may be responsible for the excellent cyclability of the oxysulfide spinel at high temperature over the 4 V region. © 2001 The Electrochemical Society. All rights reserved.
A999
Yukio Sasaki, Minoru Handa, Katsuji Kurashima, Toshiyuki Tonuma and Kyohei Usami
The thermal characteristics of lithium bis[salicylato(2-)]borate (LBSB) and its novel derivatives synthesized by us, such as lithium bis[3-methylsalicylato(2-)]borate (3-MLBSB), lithium bis[3,5-dichlorosalicylato(2-)]borate (DCLBSB), and lithium bis[3,5,6-trichlorosalicylato(2-)]borate (TCLBSB) were examined by thermogravimetric analysis (TG). The thermal decomposition in air begins at 260, 290, 310, and 320°C for TCLBSB, LBSB, DCLBSB, and 3-MLBSB, respectively. The thermal stabilities of 3-MLBSB and DCLBSB are nearly equal to those of
and
The order of the stability toward oxidation of these organoborates is
which differs from the thermal stability. Ionic dissociation properties of LBSB and its derivatives were examined by conductivity measurements in ethylene carbonate-1,2-dimethoxyethane (EC-DME) equimolar binary dilute solutions. The conductivities of the 0.1 mol dm−3 DCLBSB and TCLBSB electrolytes become higher than those in the LBSB and 3-MLBSB electrolytes. It means that DCLBSB and TCLBSB have high dissociating abilities in EC-DME mixture. The 0.5 mol dm−3 LBSB/EC-DME equimolar binary solution exhibits the highest lithium electrode cycling efficiency of more than 85% in the higher range of cycle numbers. This is a good electrolyte for rechargeable batteries. © 2001 The Electrochemical Society. All rights reserved.
A1004
Doron Aurbach, Alexander Schechter, Moty Moshkovich and Yair Cohen
Magnesium deposition processes from ethereal solutions of Grignard salts of the RMgX type (
aryl groups and
Cl, Br), and complexes of the
type
B, 
or aryl groups and
were investigated. These complexes can be considered as interaction products between
bases and
Lewis acids. The use of such complexes in ether solvents enables solutions of high anodic stability to be obtained, which can be suitable for rechargeable Mg battery systems. In situ scanning tunneling microscopy, scanning electron microscopy in conjunction with element analysis by dispersive X-ray, electrochemical quartz crystal microbalance, and impedance spectroscopy were used. Mg deposition in all the solutions studied initially form a porous deposit that becomes compact and crystalline as the process continues. It was found that the morphology of Mg deposition is strongly dependent on the solution’s composition. This is because these processes are accompanied by adsorption processes. The specific adsorbed species in each solution probably influence the nucleation processes and thus affect the final morphology of Mg deposition in each solution. There is a clear correlation between the morphology of these processes and the cycling efficiency of Mg anodes measured in each solution. The results thus obtained are important for R&D of rechargeable Mg battery systems. © 2001 The Electrochemical Society. All rights reserved.
A1015
A. A. F. Grupioni and T. A. F. Lassali
A new electrode based on
(30:70 mol %) composition has been prepared by thermal decomposition (400°C) from mixtures of chloride precursors and characterized by energy dispersive X-ray, scanning electron microscopy, X-ray diffraction analysis, cyclic voltammetry, and charging/discharging curves. The electrochemical behavior shows dependence on the cathodic potential limit employed, and a good potential window (1.4 V) in aqueous NaOH and high electrocatalytic area due to the contribution of different redox transitions of Ir and Co surface sites. The electrode has been found to perform as superior electrodes in electrochemical capacitor applications with a specific capacitance of
The large capacitance exhibited by this system arises from a combination of the double layer capacitance and pseudocapacitance associated with surface redox-type reactions. © 2001 The Electrochemical Society. All rights reserved.
A1023
Xiao Guang Yang and Bor Yann Liaw
We have investigated the charge performance of a commercially available 85Ah nickel metal hydride (Ni-MH) battery system. Each of the Ni-MH battery modules contains 11 prismatic cells designed for electrical vehicle traction applications. This work focused on understanding the operating mechanism of the charging process and the influence of different constant current charge regimes, with rates ranging from C/8 to 1C, on the charge performance. We found that the cell voltage profile was dominated by the potential change of the nickel electrode in the charge regime. At C/4 (20 A), which is commonly used in the charge algorithm, the modules can be effectively and fully recharged with a low degree of overcharge of 1-2%. When being charged at C/2 (40 A) with a proper control of the cell pressure (at a pressure lid of 6.8 atm or 100 psi), the modules can be recharged with a high efficiency to 93% state-of-charge (SOC). In this case, we found that the oxygen evolution accelerated after reaching 70% SOC, and an
-oxidizing recombination” mechanism was present, based on the observation of the potential variation of the metal hydride electrode. When the modules were charged at 1 C rate, we found that, in addition to the oxygen evolution/recombination cycle, another
-reducing recombination” mechanism was present and was related to the occurrence of
in the final stage of the charge regime. The presence of the
resulted in a noticeable capacity loss at high charge rates. Interestingly, most of the capacity loss can be recovered after several recovering cycles operating at a very low rate (e.g., C/8). We attribute this temporary loss of reversible capacity (rechargeability) to severe hydrogen gassing during the high rate charge at the metal hydride electrode and the associated “reversed oxidation” via the
-reducing recombination on the nickel electrode. This phenomenon subsequently resulted in a significant temperature rise in the cell, causing localized dryout, and a capacity mismatch between the two electrodes. © 2001 The Electrochemical Society. All rights reserved.
A1029
Robert S. Rubino, Hong Gan and Esther S. Takeuchi
Identical electrodes wound in both a cylindrical and a prismatic configuration provided different capacity fade rates. At the completion of 300 cycles with a C/2 charge and 1C discharge, the prismatic cells faded 24% and the cylindrical cells faded 16%. In the cylindrical-type cell, the fade was primarily caused by a reduction in the capacity of the cathode. The higher fade rate in the prismatic cell was attributed to lower cell stack pressure which resulted in more anode swelling during cycling. The increased porosity of the anode in this cell reduced the integrity of the electrical conduction network causing many graphite particles to become isolated or less accessible. © 2001 The Electrochemical Society. All rights reserved.
A1034
K. Takizawa and A. Hagiwara
A1041
Myoung Youp Song, Dongsu Ahn, Ik Hyun Kwon and Sung Hyo Chough
A series of multicomponent
(M = Fe, Co, Cu, Mo, and Al) alloys are prepared and their crystal structure and pressure-composition-temperature curves are examined. The electrochemical properties of these alloys such as discharge capacity, cycling performance, and rate capability are also investigated.
(M = Fe, Co, Cu, Mo, and Al) alloys have predominantly C14 Laves phases multiple phase structure. The alloys with M = Co and Fe have relatively larger hydrogen storage capacities. The discharge capacities just after activation are relatively large in the case of the alloys with M = Co and Fe. They are 226 and 225 mAh/g, respectively, at the current density 60 mA/g. The
alloy is the best one with a relatively large discharge capacity and good cycling performance. The gradual increases in the discharge capacities of the alloys with the increase in the current density (from 60 to 250 mA/g) are considered to result from the spontaneous hydrogen evolution due to an insufficient hydrogen overvoltage. During activation Ni-rich and Fe-rich regions form on the surface of the
alloy. They may act as active sites for the electrochemical reaction. With the increase in the number of charge/discharge cycles for the
alloy, the quantities of the zirconium and iron dissolved in the solution increase. © 2001 The Electrochemical Society. All rights reserved.
A1045
Petr Krtil and Dina Fattakhova
Corrosion, Passivation, and Anodic Films
B333
H. Ehahoun, C. Gabrielli, M. Keddam, H. Perrot, Y. Cètre and L. Diguet
In this paper, a new corrosion sensor based on a quartz crystal microbalance is presented. A 50 μm thick disk of solid metal is glued directly on the surface of a 2 MHz AT-cut quartz crystal. An electronic oscillator designed for highly damped quartz resonators allows the resonance frequency of the quartz-glue sample system to be followed. Simultaneous electrochemical measurements are possible as the metal sample can be polarized. The mass sensitivity of this electrochemical quartz crystal microbalance was determined by carrying out a copper electrodeposition directly on the sample surface. The potentiostatic dissolution of 304 stainless steel in 1 M HCl is discussed in this paper. The mass loss during potentiostatic dissolution was measured by the frequency shift of the microbalance sensor and compared to the mass loss calculated from Faraday’s law. A very good agreement was found as both results had a relative difference lower than 5%. © 2001 The Electrochemical Society. All rights reserved.
B337
Y.-M. Li and L. Young
The non-thickness-limited (NTL) growth phenomenon reported by Melody et al. in which anodic oxide films on tantalum continue to grow in dry glycerol solutions of dibasic potassium phosphate to large thicknesses (tens of micrometers) at low applied voltages (tens of volts) was investigated using mostly constant current growth. The field strengths in the oxide for growth of anodic oxide films at 180°C with constant current density in wet glycerol solutions (1 vol % water) were in the MV/cm range and close to those calculated from the equations fitted to data from growth in aqueous solutions at lower temperatures. At constant current density and 180°C in dry glycerol solutions, the field fell with time and eventually the voltage decreased as the NTL state developed. The current efficiency for the growth of oxide was estimated by comparing thickness increase measured by ellipsometry with that calculated from the charge passed. It was lower in the NTL state. This is consistent with increased electronic conductivity in the oxide. The dielectric losses of the NTL films were much higher than those of films grown in wet glycerol solutions. Those grown in wet glycerol showed the normal, almost frequency independent, tan δ as found for ordinary anodic oxide growth on tantalum. Those grown in dry glycerol solutions showed increasing tan δ as the frequency decreased, consistent with increased electronic conductance through the oxide. It is suggested that the increased electronic and ionic conductivity in the NTL state may be caused by nonstoichiometry induced by the change in hydroxyl ion availability to the oxide suggested by Melody et al. when dry glycerol solutions are used. © 2001 The Electrochemical Society. All rights reserved.
B343
Digby D. Macdonald, Mohammed Al Rifaie and George R. Engelhardt
A new rate law for the growth of anodic passive films on metal surfaces is derived from the point defect model (PDM). The model recognizes both the growth of the barrier oxide layer into the metal via the generation of oxygen vacancies at the metal/film interface and the dissolution of the barrier layer at the film/solution interface. The new rate law accounts for the existence of a steady state in film thickness, as well as for the transients in thickness and film growth current as the potential is stepped in the positive or negative direction from an initial steady state. The predictions of the PDM, with respect to the thickness of the barrier layer, are compared with those of the high field model. The latter cannot account for the existence of steady states or the decrease in barrier layer thickness on stepping the potential in the negative direction. The predicted transients in film thickness and growth current density are in good fidelity with the measured transients on tungsten in pH 1.5 phosphate buffer solution as the voltage is cycled between 10 V in reference to saturated calomel electrode
and 6
Finally, the new rate law accounts for passive film thinning under negative potential step conditions as the pH is changed over the range of 1.5 to 5.1 and as the initial and final voltages are changed in a systematic manner, such that the voltage excursion is constant. © 2001 The Electrochemical Society. All rights reserved.
B348
T. Ramgopal, P. Schmutz and G. S. Frankel
B357
B. Malki, A. Legris, J.-L. Pastol, G. Lorang and D. Gorse
B368
Michelle Gaudett Koul and John R. Scully
The mechanisms by which hydrogen desorbs from Ti-3 Al-8 V-6 Cr-4 Mo-4 Zr in the presence of a native oxide film under vacuum were examined over a range of temperatures using thermal desorption spectroscopy (TDS) and X-ray photoelectron spectroscopy (XPS). Hydrogen release was extremely limited and not measured below 260°C due to the thermal stability of the surface oxide. XPS experiments indicate that hydrogen release is not observed in vacuum until after the oxide film is completely dissolved. However, in the temperature range 325-490°C, TDS measurements indicate that hydrogen desorption is bulk diffusion controlled with a high desorption activation energy (135-144 kJ/mol). XPS measurements in conjunction with H desorption measurements indicate a slow, but measurable desorption rate following oxide dissolution, with the presence of a high relative O content (25-50 atom %) at the metallic surface. H desorption is rationalized to be diffusion-limited by an O-enriched Ti surface layer at these temperatures. Surface recombination controlled desorption was observed by TDS at temperatures exceeding 490°C. XPS results indicate that the transition from diffusion control to surface recombination control (and an increased desorption rate) is likely coincident with a reduction of the relative surface O content in the alloy to below 25 atom %. Qualitative desorption simulation results indicate agreement with a model that includes H egress by diffusion and surface recombination coupled in series. However, quantitative agreement cannot be obtained without accounting for the effect of the O-enriched surface layer on bulk H diffusion parameters. © 2001 The Electrochemical Society. All rights reserved.
C569
Shin-Jung Choi, Dae-Ha Woo, Noseung Myung, Heon Kang and Su-Moon Park
C574
Yan Zhang, K. L. Tan, G. H. Yang, E. T. Kang and K. G. Neoh
C583
Constantin Vahlas, Pablo Ortiz, Djar Oquab and Ian W. Hall
This paper presents results on the chemical vapor deposition of aluminum on silicon carbide starting from triisobutylaluminum. The deposited films show important systematic trends in surface roughness and porosity. Considering literature information on the deposition of aluminum on silicon, pretreatments of the deposition surface with hydrofluoric acid and/or titanium tetrachloride have been tested. They lead to films with a smoother morphology and stronger adhesion with the substrate than in the case of an untreated surface. Different heteroelements are observed at the interface under these conditions. A short thermal activation of the nucleation process following these pretreatments does not unambiguously improve the characteristics of the aluminum films. The obtained results can be considered for the modification of surface characteristics of silicon carbide particles which are used in discontinuously reinforcement aluminum composite materials with the aim to improve their mechanical properties and corrosion resistance as well as their fabrication process. © 2001 The Electrochemical Society. All rights reserved.
C590
Hong-Hui Hsu, Chao-Chan Hsieh, Min-Hsian Chen, Su-Jien Lin and Jien-Wei Yeh
C599
Sung-Il Cho, Chan-Hwa Chung and Sang Heup Moon
The decomposition behavior of titanium tetraisopropoxide [TTIP,
on Si(100) has been studied using a thermal desorption technique in vacuum. TTIP is dissociated on Si(100) at temperatures below 350 K so that the silicon surface is covered with isopropoxy ligands and hydrogen, which originate from the TTIP. The isopropoxy ligands react with hydrogen on the silicon surface to produce isopropanol at temperatures between 350 and 650 K, and some of the ligands produce propylene and acetone in the range of 500-700 K. Hydrogen exists as monohydride on the silicon surface showing a characteristic desorption peak at 780 K. At higher dosages, TTIP is not completely dissociated and some of the isopropoxy ligands remain bound to titanium even at 700 K. These intact ligands of TTIP produce acetone/isopropanol or propylene in the temperature range of 800-1000 K by disproportionation among themselves or by the simple decomposition of the C-O bond in the ligands. © 2001 The Electrochemical Society. All rights reserved.
C604
Frédéric Lantelme, Thierry Cartailler, Youssef Berghoute and Mohamed Hamdani
The thermodynamic and kinetic properties of solutions of lanthanide (lanthanum, cerium, praseodymium, gadolinium) and yttrium chlorides in fused alkali chlorides were obtained from transient electrochemical techniques. Digital simulation was used to obtain a precise analysis of transient responses including perturbing factors such as ohmic drop, electrocrystallization, and reduction of alkali ions. A fitting procedure, included in the numerical calculation, allows an accurate determination of reaction parameters, diffusion coefficients, standard potentials, and covering factor. The technique was extended to the formation of lanthanum and gadolinium alloys with nickel. © 2001 The Electrochemical Society. All rights reserved.
C614
T. Zambelli, M. L. Munford, F. Pillier, M.-C. Bernard and P. Allongue
Alkaline CuCN solutions were used to deposit electrochemically homogeneous and adherent Cu films onto H-terminated silicon surfaces. Careful control of the deposition potential leads either to perfect n-Si(111)/Cu Schottky diodes (barrier height
tunable between 550 and 700 mV; best ideality factor
or ohmic contacts (3-10 Ω). Aging of electrical properties was also investigated, and the film porosity is discussed. Transmission electron, ex situ atomic force and in situ scanning tunneling microscopy observations of the interface structure and of the film nucleation are presented. The excellent adherence of alkaline copper on silicon was exploited to plate ferromagnetic metals (nickel, cobalt, and iron) from modified Watts baths (pH 3), using a two-step procedure. © 2001 The Electrochemical Society. All rights reserved.
C620
J. J. Kelly, M. Cantoni and D. Landolt
Scanning and transmission electron microscopy (TEM) were used to characterize the microstructure of electrodeposited multilayer Cu-Co alloys. Both columnar alloys (where the Co is localized to the columns) and three-dimensional arrays (where the Co is present in regions less than 1 μm diam) were studied. The latter type was produced by successively electrodepositing a columnar alloy layer between Cu spacer layers, resulting in a semiordered, three-dimensional network of Co-rich regions in a principally Cu matrix. The composition gradient between the Co-rich regions and the Cu matrix was verified by electron energy loss spectroscopy and energy-dispersive spectroscopy using TEM. It was found that the size of the Co-rich regions was affected more by the overall alloy layer composition than by the deposition parameters. Under appropriate conditions, it was possible to reduce the individual alloy layer thickness to 25 nm while maintaining chemical segregation between the Co-rich areas. Annealing at 250°C and higher caused the Co-rich regions to merge together. © 2001 The Electrochemical Society. All rights reserved.
C627
Takuya Nakanishi, Masaki Ozaki, Hyo-Seung Nam, Tokihiko Yokoshima and Tetsuya Osaka
A pulsed electrodeposition method was applied to the preparation of soft magnetic CoNiFe films in the compositional region corresponding to the phase boundary between face-centered cubic (fcc) and body-centered cubic (bcc) structures. Crystalline grain size was found to be almost the same, smaller than 10 nm, and independent of the duty cycle which is the ratio of the pulse-on time to the pulse-on plus pulse-off period. Depending on the operating conditions, the ratio of bcc to fcc varied. Current efficiency decreased with decreasing duty cycle and pulse current density. The intensity ratio of bcc(110) to fcc(111) X-ray diffraction peaks showed a maximum at the operating conditions in which the transition from kinetic to mass-transfer controlled deposition occurred with only a slight increase of Fe content (approximately 1 atom %). Magnetic properties were suggested to be controllable by adjusting the bcc-fcc ratio using pulsed electrodeposition. © 2001 The Electrochemical Society. All rights reserved.
C632
Takeo Kubota, Nobuyoshi Hara and Katsuhisa Sugimoto
C640
L. Santinacci, T. Djenizian and P. Schmuki
In this study, we investigate the possibilities of selectively electrodepositing Cu on surface defects created in p-type and n-type Si(100) by scratching the surface with the tip of an atomic force microscope (AFM). Nanosized grooves were produced on Si surfaces with a diamond-coated AFM tip at heavy forces. Cu was electrodeposited on these grooved surfaces from a
electrolyte under various conditions. The results clearly show that defects created on H-terminated p-type Si(100) lead to an enhanced reactivity, i.e., preferential Cu deposition at such defects is possible. However, a much higher degree of selectivity of the deposition is obtained if AFM-induced grooves are produced on surfaces that carry a native oxide layer. The masking effect of this insulator film is demonstrated by selective Cu electrodeposition into scratches on oxide-covered p- and n-type silicon. After an optimization of electrochemical parameters, we achieved the deposition of uniform and well-defined nanostructures. The process presented here opens new perspectives for selective electrodeposition and direct patterning of Si surfaces. © 2001 The Electrochemical Society. All rights reserved.
C647
Jean-Claude Bradley, Sundar Babu, Aditya Mittal, Patrick Ndungu, Beth Carroll and Benjamin Samuel
The pulsed bipolar electrodeposition of palladium onto 1-2 μm graphite particles was investigated. The amount of palladium deposited was strongly correlated with field intensity, showing an abrupt increase at 2-3 kV/cm. The electrodeposition was successful for frequencies ranging from 500 Hz to 20 kHz, and the amount of deposited palladium was independent of the frequency used. These results demonstrate that the preparation of bipolar electrodeposited catalysts can be achieved within a very large frequency window. Palladium surface area measurements indicate an increase in dispersion with increasing frequency. Sonication of the graphite prior to deposition leads to significantly greater palladium dispersion. Electron microscopy characterization reveals three types of growth: surface-bound, ramified, and amorphous. The surface-bound growth appears as spherical deposits on the order of 5 nm in both dc and pulsed-field experiments. The ramified deposits consist of interconnected 25-50 nm diam spherical structures extending from the graphite particles and appear in the samples prepared at all studied frequencies. © 2001 The Electrochemical Society. All rights reserved.
Electrochemical Synthesis and Engineering
D109
R. C. DeMattei, A. Watcharapasorn and R. S. Feigelson
The binary pnictide skutterudites, 
have been successfully synthesized for the first time by molten salt electrolysis. The melt for depositing
contained CoO and
and graphite rods were used for both anode and cathode. All experiments were run in a flowing
gas atmosphere. By adjusting the melt composition, single phase
could be prepared. Attempts were also made to deposit
using platinum and silver strip electrodes. Although
powder was obtained in the crucible, no
deposit was found on the Pt cathode, which was attacked by the phosphorus present in the melt and produced platinum phosphide
A low deposition rate was observed for Ag cathodes, and as a result, a very small amount of material was deposited. This made it difficult to determine the type and number of phases formed. Using graphite electrodes, two other cobalt skutterudites were prepared.
was synthesized from a
melt and
from a
melt. While the skutterudite phases were formed in these systems, the optimal melt compositions and other experimental conditions necessary to prepare single phase deposits still need to be determined. © 2001 The Electrochemical Society. All rights reserved.
D112
B. V. Tilak, V. I. Birss, J. Wang, C.-P. Chen and S. K. Rangarajan
Freshly formed Ru/Ti oxide anodes, containing between 5 and 40 atom % Ru, have been examined for their Tafel behavior during chlorine evolution, as well as their cyclic voltammetric (CV) and ac impedance response at the open-circuit potential, in chlorine-free NaCl solutions. Also, 30 atom % Ru electrodes have been electrochemically deactivated, as seen by an increase in the anode potential and the Tafel slope for the chlorine evolution reaction during long-term electrolysis. A comparison of the data for the fresh and the deactivated anodes suggests that the deactivated anodes have similar electrochemical characteristics as freshly formed, low-Ru-content (ca. 5 atom %) oxide films. To understand this better, the experimentally obtained ac impedance data were compared to the calculated impedance, based on a porous film model in which a one-electron surface redox reaction occurs. While the fit is good at medium-to-high frequencies, the inclusion of a diffusion-controlled process for the low atom percent Ru films is required to achieve a good fit also at low frequencies. Taken together, these results support the hypothesis that the deactivation of originally high atom percent Ru anodes is due to the depletion of Ru from the oxide film, causing its electrochemical behavior to become more similar to that of freshly formed low atom percent Ru oxide films. © 2001 The Electrochemical Society. All rights reserved.
Physical and Analytical Electrochemistry
E357
R. M. Abouatallah, D. W. Kirk, S. J. Thorpe and J. W. Graydon
E364
Vladimir Blinov, Signe Kjelstrup, Dick Bedeaux and Viktor Sharivker
The Seebeck coefficient of a cell with lead electrodes and electrolyte of molten lead chloride and alkali chloride is investigated experimentally and theoretically for mole fractions of
between 1 and 0.3 in alkali chlorides. An equation is derived from irreversible thermodynamics linking the transported entropy of lead ion to the chemical potential of the polarized lead at the surface. The path across the cell is taken to be adiabatic in this derivation. Experimental results indicate that the transported entropy of lead ions depends on the radius of the alkali ion. © 2001 The Electrochemical Society. All rights reserved.
E372
M. L. López, V. Compañ, J. Garrido, E. Riande and J. L. Acosta
The preparation of new cation-exchange membranes from polymer composites based on poly(vinylidene fluoride), sulfonated polystyrene-co-divinylbenzene, and antimonic acid is reported. The thermal properties of the composites have been characterized by differential scanning calorimetry. Values of the transport number of protons in the membranes were obtained from the observable electric potential. It is defined from the potential difference measured between the electrodes reversible to one of the constituent ions in equilibrium with the system. When compared with Nafion cation-exchange membranes, the membranes described in this work exhibit interesting proton transport properties that could make them suitable as polymer electrolytes in fuel cells. © 2001 The Electrochemical Society. All rights reserved.
E378
Sang-Jin Moon, Won-Wook So and Hye-Young Chang
Cadmium sulfide (CdS) particulate film electrodes were prepared by coating nanosized CdS colloidal sols onto fluorine-doped tin oxide conducting glass, and treated with titanium tetrachloride aqueous solution. The variation of photoelectrochemical properties of these electrodes according to the surface treatment was investigated with respect to photocurrent and surface morphology. Porous films composed of coarsely interconnected CdS particles before treatment became more compact and stable after treatment. It was also found that the
component was formed homogeneously throughout the entire film. This etching and
effect brought about densification of the films, a decrease of film surface area, and an enhancement of the photocurrent. Especially, the stabilities of the electrodes measured by chronoamperometry were remarkably improved by the treatment, suggesting the effectiveness of this approach. © 2001 The Electrochemical Society. All rights reserved.
E382
Yuria Saito, Hiroshi Kataok and Shigehito Deki
E386
Lara I. Halaoui, Hossein Sharifian and Allen J. Bard
The scanning electrochemical microscope (SECM) was used to study the electrochemical reduction of nitric acid to hydroxylamine at modified glassy carbon (GC) electrodes. The GC surface was modified by holding it at a negative potential in solutions of p-aminophenol, or p-phenylenediamine in 1.0 M nitric acid. The generated products were detected in generation/collection experiments with an SECM Pt ultramicroelectrode. The films that form on GC, apparently polymers of a quinone imine intermediate, can also be grown under similar conditions on indium tin oxide (ITO) coated glass electrodes and appeared as dark orange-brown films. Atomic force microscope imaging revealed a highly porous structure. SECM and cyclic voltammetry studies showed that as a result of this surface filming, the GC electrodes exhibited an increase of at least 1 V in the hydrogen overpotential relative to the unmodified surface and the efficiency of the electrochemical reduction of nitric acid to hydroxylamine was dramatically enhanced. Bulk electrolysis of nitric acid at carbon in the presence of p-phenylenediamine resulted in a 75 to 85% current efficiency for hydroxylamine production at current densities of 0.5 to 0.8 A/cm2. This procedure proved to be useful for the large-scale electrochemical production of hydroxylamine from nitric acid at an electrode other than liquid mercury. © 2001 The Electrochemical Society. All rights reserved.
Dielectric Science and Materials
F175
Takeshi Furusawa, Daisuke Ryuzaki, Ryo Yoneyama, Yoshio Homma and Kenji Hinode
Resistance of siloxane-based, low-dielectric-constant (low-k) dielectrics against heat and moisture stress is clarified. The organo-silica-glass (OSG) and the silicon-oxycarbide are shown to be the most reliable: the k-values are stable even after a heating test at 650°C and a pressure cooker treatment for 100 h. This stability is high enough to ensure the low-k property throughout fabricating multilevel interconnects and long-term reliability after the fabrication. This is shown to be due to the stability of
bonds and
bonds incorporated in the OSG and the silicon-oxycarbide. The stability of the OSG in real low-k interlevel dielectric structure was also demonstrated using four-level interconnect test devices. The low-k property still remains even after the reliability tests, showing that the low-k interlayer dielectric structure is sufficiently resistant to heat and moisture stresses. © 2001 The Electrochemical Society. All rights reserved.
F180
Jiang Li Cao, Long Tu Li, Yong Li Wang and Zhi Lun Gui
F184
C.-T. Wu, R. Ridley, P. Roman, G. Dolny, T. Grebs, J. Hao and J. Ruzyllo
F189
Dae-Gyu Park, Heung-Jae Cho, Kwan-Yong Lim, Tae-Ho Cha, In-Seok Yeo and Jin Won Park
Semiconductor Devices, Materials, and Processing
G465
Ajit Paranjpe, Sanjay Gopinath, Tom Omstead and Randhir Bubber
G472
J. W. Lee, M. H. Jeon, G. S. Cho, H. C. Yim, S. K. Chang, K. K. Kim, M. Devre, Y. S. Lee, R. Westerman, D. Johnson et al
We developed optical emission spectroscopy based end-point detection techniques for GaAs-based etching in inductively coupled
plasmas. It was found that an emission peak of Ga (417 nm) was quite useful as a tracer for in situ process monitoring during both AlGaAs/GaAs and InGaP/GaAs multilayer etching. The intensity of the Ga emission peak increased significantly during AlGaAs/GaAs etching in a
inductively coupled plasma when the GaAs layer was exposed to the plasma. We found the same result with InGaP/GaAs etching. Utilization of the Ga peak signal is very important during the plasma process for GaAs-based device fabrication, especially for high electron mobility transistors and heterojunction bipolar transistors in order to minimize overetch time during the nonselective etching. The technique provides a breakthrough for in situ end-point detection of GaAs-based nonselective plasma etching. © 2001 The Electrochemical Society. All rights reserved.
G475
K. Sugawara, K. Ozeki, K. Fujioka, Y. Mamada, M. Igai and H. Hirayama
The electrical properties of semiconductor devices are directly related to the dopant concentration in single crystals. Therefore, to make semiconductor devices with controllable electrical properties, it is important to control the dopant concentration accurately, both along the growth axis and in the radial direction. The dopant concentration along the growth direction can be described by the normal freezing equation and is well understood, but the factors controlling the dopant distribution in the radial direction are not well understood. We, therefore, made a detailed, quantitative analysis of the radial dopant distribution in Czochralski silicon crystals by solving the coupled Navier-Stokes, continuity, and energy equations for the silicon melt flow and temperature fields, and by solving the diffusion and segregation equations for the phosphorus distribution in the melt and in the crystal. Good agreement between measured and simulated results of the radial phosphorus concentration in silicon single crystals was obtained. The melt was exposed to a background gas of Ar into which
was added to counteract evaporation of the phosphorus from the melt. Simulated radial phosphorus concentration distributions compared well with measured radial distributions, and the
added to the background Ar gas increased the average melt dopant concentration and also improved the radial phosphorus concentration uniformity. © 2001 The Electrochemical Society. All rights reserved.
G481
Pei-I Wang, S. P. Murarka, D. A. Kaminski, S. Bedell and W. A. Lanford
G487
F. De Smedt, S. De Gendt, M. M. Heyns and C. Vinckier
The solubility of ozone in aqueous solutions expressed as a pseudo-Henry’s law coefficient for ozone,
is measured over a pH range of 1 to 8, and temperature range of 15 to 45°C in the presence of several additives: HCl,
HAc (Ac is acetate), NaAc, and NaOH. The value of
was found to be a function of temperature, pH, and nature of the anion. The pseudo-Henry’s law coefficient is maximal at low pH and decreases with rising pH of the aqueous solution. The addition of chloride enhances the ozone decay rate and thus decreases the solubility below pH 2 while the addition of acetic acid/acetate results in an increase of
for
The solubility enthalpy
for ozone is found to be equal to
For applications of ozone in semiconductor cleaning processes, knowledge of the dependence of
on pH, temperature, gas phase concentration, and additive is important in order to achieve optimized cleaning conditions. © 2001 The Electrochemical Society. All rights reserved.
G494
Maria Ronay
The paper describes the development of an aluminum chemical mechanical planarization process that was successfully integrated into the dual damascene technology producing 1 Gb dynamic random access memory chips meeting all yield and sheet resistance requirements. Three of the major problems of chemical mechanical polishing of Al-0.5 Cu alloys, i.e., copper plate-out on titanium liners, array erosion, and slow polish rate were solved by adding
ions to the polishing slurry. © 2001 The Electrochemical Society. All rights reserved.
G500
Shui Jinn Wang, Hao Yi Tsai, S. C. Sun and M. H. Shiao
G507
A. Poyai, E. Simoen, C. Claeys, R. Rooyackers and G. Badenes
The use of a p-n junction diode as a tool for the assessment of the p-well quality is demonstrated, by analyzing in detail the current-voltage and capacitance-voltage characteristics of
junctions surrounded by either shallow trench isolation or polysilicon encapsulated local oxidation of silicon. As a reference, diodes fabricated in a p-type substrate and defined by a local oxidation of silicon isolation have been used. Particular emphasis is on the lifetime properties and leakage current activation energy of the p-well region, which has been fabricated by a deep (200 keV) and a shallow (55 keV) boron ion implantation. That the leakage current of large area diodes is governed by electric field-assisted generation of carriers from residual, unannealed deep B-implantation damage is demonstrated. The presence of such defects is confirmed by deep level transient spectroscopy analysis. The generation lifetime profile in the depletion region and the reverse current activation energy are extracted by taking account of the electric field enhancement factor of the thermal generation. Finally, it is shown that the generation lifetime and residual defects depend mainly on the global thermal budget and little on the isolation scheme used. © 2001 The Electrochemical Society. All rights reserved.
G513
Glenn W. Gale, David L. Rath, Emanuel I. Cooper, Scott Estes, Harald F. Okorn-Schmidt, Jeffrey Brigante, R. Jagannathan, Greg Settembre and Ed Adams
To realize environmental and cost benefits it is desirable to reduce the RCA cleaning sequence from its historical
combination, in which the particle-removing SC1 solution deposits certain metals, necessitating the metal-removing SC2. One approach is to add a chelating agent to the SC1. Extensive testing of SC1 solutions with addition of the complexing agent 1,2-cyclohexanediaminetetraacetic acid (CDTA) were performed. CDTA was shown to be more stable than other complexing agents in SC1 solutions, facilitating significant bath life extension. Further, SC1 solutions with CDTA were shown to be capable of removing large quantities of metals from contaminated wafers, comparable to SC2, and preventing deposition of metals. An exception is aluminum, which can deposit from SC1 even with large amounts of added CDTA, but which can be removed by a subsequent dilute
step. © 2001 The Electrochemical Society. All rights reserved.
G517
S. Sama, M. Porrini, F. Fogale and M. Servidori
Czochralski silicon crystals, grown with different interstitial oxygen concentrations (group I) or different types of intrinsic defects (group II), were analyzed by X-ray section topography, diffuse X-ray scattering, surface photovoltage, microwave photoconductive decay, and Fourier infrared spectroscopy. The samples of group I showed that the main factor influencing the X-ray section topography images is the amount of precipitated oxygen. The increase in this amount involves a decrease in size and an increase in density of the oxygen precipitates. A strong reduction in the minority carrier diffusion length is observed after precipitation. These effects seem to be dependent on the positions along the ingot axis at which the samples were taken, which would indicate the influence of the sample thermal history on the detectability of oxygen precipitates by means of these techniques. The samples of group II are characterized by vacancy-rich, interstitial-rich, and defect-free regions. After copper decoration, the different defects were observed to have different sizes, densities, shapes, and depth distributions. This feature allows one to clearly distinguish between crystal zones where vacancy or interstitial clusters prevail and where defects are absent. Minority carrier lifetime values are directly related to the defect volume densities. The combined use of different characterization techniques proved itself a powerful tool to study different defect types in Czochralski silicon. © 2001 The Electrochemical Society. All rights reserved.
G524
Sangheon Lee and Yue Kuo
The chlorine plasma/copper reaction that is the base of a new copper (Cu) dry etching process was studied. The reaction product is a rough and porous Cu chloride compound film. Influences of process parameters such as plasma exposure time, pressure, plasma power, and substrate temperature, on the copper chlorination process, were explored. In addition to variations of morphology and reaction rate, we also investigated the relationship between the structure of the reaction product and the process condition. The result shows that both the plasma phase chemistry and the ion bombardment energy are critical to the reaction mechanism and the reaction product’s morphology. A simple model that describes the progress of the reaction through the Cu layer has been developed based on above results. This study result indicates that it is possible to etch Cu with a plasma process at room temperature. © 2001 The Electrochemical Society. All rights reserved.
G530
Jam Wem Lee, Shen-Xiang Lin, Tan-Fu Lei and Chung-Len Lee
A process design is presented for improving the thermal stability of Ni-silicide (nickel-silicide) using a stacked polysilicon gate structure. The Ni-silicide formed has low sheet resistance up to 800°C on a silicidation process. Additionally, the metal-oxide-semiconductor (MOS) capacitors fabricated using these proposed gate structures demonstrate higher electrical reliability for gate oxides than those of nonstacked films. That is, the gate oxides of the MOS capacitors were only slightly degraded after silicidation step at 800°C. In conclusion, the Ni-silicide formed on those stacked polysilicon gates are attractive in fabricating ultralarge scale integration (ULSI) circuits because both the thermal stability of Ni-silicide and the reliability of gate oxides are improved simultaneously. © 2001 The Electrochemical Society. All rights reserved.
Sensors and Displays: Principles, Materials, and Processing
H91
Rabah Boukherroub, Danial D. M. Wayner, David J. Lockwood and Leigh T. Canham
Freshly prepared porous silicon (PSi) surfaces have been modified with different organic molecules such as alkenes (1-decene, ethyl undecylenate) and nonconjugated dienes (1,7-octadiene) in a thermal process to yield organic monolayers covalently attached to the surface through Si-C bonds. These monolayers have been characterized using diffuse reflectance infrared Fourier transform, X-ray photoelectron, and Raman spectroscopies. Derivatized surfaces have shown a high stability in boiling aqueous and organic solvents, and in 49% HF and KOH (pH 13) solutions at room temperature. They protect the surface against oxidation when exposed to air at 100% humidity. The high passivation of the surface implies also photoluminescence (PL) stabilization. In fact, the modified surfaces retained their original PL, and the chemical process affected neither the peak position nor the intensity. The PL was preserved even after a steam treatment for several weeks, while the hydrogen-terminated porous layer was completely transformed into a transparent oxide. © 2001 The Electrochemical Society. All rights reserved.
H98
Marisa Luisa Grilli, Elisabetta Di Bartolomeo and Enrico Traversa
H103
Masato Sawada, Kenichi Yamaguchi, Kenichiro Momose and Hiroyasu Saka
To prolong the light emission life-span of an electroluminescent (EL) phosphor particle (ZnS:Cu, Cl), the phosphor particles were encapsulated with an antihumidity film and the relationship between the light emission life-span and the composition of the antihumidity film, as well as the film structure, was studied. The antihumidity films consisted of
and
which were deposited by chemical vapor deposition. This was achieved through hydrolysis of the
and
source precursors. The
film did not exhibit antihumidity characteristics; however, antihumidity characteristics were confirmed in the
film and the light emission life-span was prolonged. However, due to the effect of residual Cl in the
film, the indium-tin oxide (ITO) electrode of the EL device deteriorated and substantial prolongation of the light emission life-span was not possible. On the basis of these findings, we deposited a
film on the
film, and attempted to prevent the ITO electrode from deteriorating due to residual Cl ions in the
film. As a result of the introduction of a dual layer consisting of
and
films, the brightness half-life was prolonged to 200 h (at 40°C, 90% humidity, 100 V, 400 Hz). Thus, the life span of the phosphor has been expanded to approximately tenfold that of nonencapsulated phosphors. © 2001 The Electrochemical Society. All rights reserved.
H109
Young Kil Yoo, Gun Young Hong, Sung Hee Cho and Jae Soo Yoo
In this work, we prepared spherical gallate-based phosphors using an aerosol pyrolysis method. The synthetic parameters such as post heat-treatment temperature, activator concentration, and degree of reductions were optimized for the maximum cathodoluminescent (CL) intensity. For enhancing the CL luminous efficiency of phosphors, adjustment of lattice structure were also considered. It was found that the CL intensity was sensitive to the crystal structure in host lattice, which would be engineered by Al concentration in ZnGa-Al-O system. The most prominent result on the zinc aluminogallates which are of spherical shape was the brightness of 550 cd/m2 at 400 V excitation with color coordinate of
and
© 2001 The Electrochemical Society. All rights reserved.
H115
Jin Hyung Ahn and Byung Tae Ahn
H120
Hiren V. Shah, Eric L. Hanson and Georgia A. Arbuckle-Keil
Vapor-phase doping of poly(p-phenylene vinylene) (PPV) with fuming sulfuric acid has been investigated using the quartz crystal microbalance. Thin films of PPV were obtained on quartz crystal substrates by spin casting a precursor polymer, which is thermally converted to give the PPV product. Dopant mass uptake and the resistance of the film were recorded in situ during doping. A decrease in the resistance and therefore an increase in the conductivity of the film from the insulating to the metallic regime was observed. Mass uptake information was used to determine the dopant concentration at the maximum conductivity, the doping rate, and the diffusion coefficient of the polymer. The dopant concentration results were verified by Rutherford backscattering spectrometry and elemental analysis. The observation that the doped material tends to lose its metallic properties upon exposure to moisture in the atmospheric air has been used to investigate its potential as a humidity-sensing device. The golden metallic appearance of the film changes as well. The conductivity can be returned by application of a dynamic vacuum. Fuming sulfuric acid-doped films were exposed to a range of relative humidities, from 4 to 75%. A rapid and significant linear response (over four orders of magnitude) to all percent humidities was observed. Fuming sulfuric acid-doped PPV may have the potential for applications as a humidity sensor or as a disposable shut-off switch in moisture-sensitive devices. © 2001 The Electrochemical Society. All rights reserved.
H128
Byung Soo Jeon, Gun Young Hong, Young Kil Yoo and Jae Soo Yoo
Preparation and luminescent characteristics of blue-emitting
(BAM) phosphor with spherical shape for plasma display panel (PDP) application has been investigated by aerosol pyrolysis technique using dissolved nitrates solution. The characteristics of particles were examined by controlling the effects of process conditions on the crystallinity, morphology, and luminescence properties. The as-prepared particles at 1400°C showed smooth surface with spherical shape, but above that temperature, had a rougher surface due to higher crystallization. It reflects that the spherical particles were transformed into the hexagonal form with the preparation temperatures because of structure characteristic of a BAM phosphor. X-ray diffraction measurement indicates that the as-prepared particles above 1600°C had similar crystal structure to that of commercial particles. The crystallinity of the BAM phosphor played a major important factor on the luminescent intensity irrespective of particle shape. Photoluminescent characteristics of particles were compared to those of commercial particles (Nichia Co.) under vacuum ultraviolet excitation. © 2001 The Electrochemical Society. All rights reserved.
H132
Takashi Takeuchi, Shingo Watanabe, Yoshiyasu Hatano, Miki Kuwano, Yukari Eguchi, Kazuaki Yoshida, Tatsumi Ishihara and Yusaku Takita
The influence of electrode materials on the current vs. voltage characteristics of limiting-current-type zirconia cells has been investigated systematically. The cells have one or two pairs of electrodes consisting of Pt, Pd, Au, or Ag, and a cover with a pinhole, which serves to limit gas diffusion and, therefore, the electrical current of the cells. The limiting current was found to depend definitely on the catalytic activity of the electrodes for the oxidation reaction of hydrocarbon gases in oxygen and hydrocarbon-containing gases. The results were applied to improve the sensitivity of limiting-current hydrocarbon sensors. The highest sensitivity was attained for the following combination of electrodes: Pt and Ag inner electrodes and a Au outer electrode in two-inner-electrode sensors. A preliminary examination has also been made on a three-inner-electrode sensor. © 2001 The Electrochemical Society. All rights reserved.
General Topics
J45
Li-Ping Li, Guang-She Li, Yan-Feng Xue and Hiroshi Inomata
J50
X. Guo, J. Fleig and J. Maier
It is shown that the contributions of electronic and ionic charge carriers to the grain boundary conductivity can be separated by selectively blocking one of the carriers. In this way, the electronic and the ionic partial conductivity at the grain boundary of a 0.016 wt % Fe-doped
bicrystal were determined in the temperature range of 600 to 700 K and in argon. Contrary to the bulk where the electronic and the ionic partial conductivity are comparable, the grain boundary was found to be almost exclusively electronically conductive, being in agreement with the expected more severe depletion of oxygen vacancies in the space charge layers. © 2001 The Electrochemical Society. All rights reserved.
Miscellaneous
L5
P. J. Bouwman, B. A. Boukamp, H. J. M. Bouwmeester, H. J. Wondergem and P. H. L. Notten
© 2001 The Electrochemical Society. All rights reserved.
L6
Shen Ye, Taro Inchihara and Kohei Uosaki
© 2001 The Electrochemical Society. All rights reserved.