Batteries, Fuel Cells, and Energy Conversion
A259
Venkat R. Subramanian, Deepak Tapriyal and Ralph E. White
A boundary condition for electrolyte concentration at the porous electrode/separator interface is developed. This boundary condition helps predict the electrolyte concentration profile in the porous electrode without having to solve for the concentration profile in the separator. © 2004 The Electrochemical Society. All rights reserved.
A264
Sagar Mitra and S. Sampath
Exfoliated graphite (EG) is proposed as an electrode material for solid-state electrochemical capacitors. The EG-based capacitors assembled with a solid electrolyte of polyethylene oxide-ethylene carbonate-propylene carbonate-
show high specific capacitance in the range of
The capacitors also show excellent cyclability. The response time is very short and is of the order of milliseconds. © 2004 The Electrochemical Society. All rights reserved.
A269
Shohji Tsushima, Kazuhiro Teranishi and Shuichiro Hirai
Magnetic resonance imaging (MRI) to measure the spatial distribution of the water content within a polymer electrolyte membrane (PEM) under fuel cell operation is described. By designing and building a fuel cell that can operate in an MRI system and making measurements during the cell operation, the water concentration gradient in the PEM and the overall water content decreased with an increase of the cell current. Furthermore, the water content in the anode side of the PEM decreased significantly within 200 s of the cell start-up, and this caused a similarly rapid decrease of the cell voltage. © 2004 The Electrochemical Society. All rights reserved.
A273
Kang Xu, Unchul Lee, Shengshui Zhang, Jan L. Allen and T. Richard Jow
A278
Jesús Santos Peña, Izabela Sandu, Olivier Joubert, Flor Sánchez Pascual, Carlos Otero Areán and Thierry Brousse
A first study on the electrochemical reaction between lithium and germania (β-quartz germanium oxide) is reported. Galvanostatic and potentiostatic discharges are defined by three voltage regions where different processes take place. In region I, delimited between open-circuit voltage and 0.65 V vs.
some germania particles may react with lithium to form an amorphous lithium germanate,
detectable by infrared spectroscopic measurements. Crystallinity degradation is also observed in region II (0.55-0.35 V) where germania and lithium germanate react with 4.2 mol of Li to yield a germanium/lithia nanocomposite and LiGe. Region III (0.35-0.05 V) corresponds to further reaction between lithium and germanium particles that promotes huge volume changes in the electrode. A solid electrolyte interface (SEI) developed at every step of discharge thus consuming extra lithium. Both factors, the particles expansion and the SEI, are mainly responsible for capacity fade upon cycling. © 2004 The Electrochemical Society. All rights reserved.
A282
S. P. Jiang, Sam Zhang, Y. D. Zhen and A. P. Koh
A286
Xuguang Li, Shanhai Ge, C. L. Hui and I-Ming Hsing
Well-dispersed Pt nanoparticles of an average size 2.2 nm were produced on multiwalled carbon nanotubes (MWNTs) pretreated by concentrated sulfuric and nitric acids to improve the catalyst adsorption. Reduction of the chloroplatinic acid was done by methanol. A zwitterionic surfactant 3-(N,N-dimethyldodecylammonio)propanesulfonate was used to stabilize the size of the nanocatalyst. This method is simple and reproducible. The resultant catalyst exhibits a slightly higher performance for the oxygen reduction reaction than the corresponding Pt/C. © 2004 The Electrochemical Society. All rights reserved.
A290
Clare P. Grey, Won-Sub Yoon, John Reed and Gerbrand Ceder
A combination of first principles calculations and lithium NMR spectroscopy was used to examine the effect of electrochemical cycling on lithium ions located in the transition metal layers in layered lithium nickel manganates. These lithium ions participate in the electrochemical process with NMR results showing that they are removed from the octahedral sites on charging, but return on discharging. Calculations indicate that the lithium ions become increasingly unstable, as the concentration of vacancies in the lithium layers increases. A lithium ion nearby three vacancies in the lithium layers drops immediately, with no activation barrier, into the adjacent tetrahedral site in the lithium layers; charging to higher potentials is then required to remove this lithium ion. © 2004 The Electrochemical Society. All rights reserved.
A294
Alastair D. Robertson and Peter G. Bruce
Corrosion, Passivation, and Anodic Films
B31
Devicharan Chidambaram, Gary P. Halada and Clive R. Clayton
It has long been hypothesized and recently shown that hexavalent chromium ions in the chromate conversion coating (CCC) migrate to active sites. This repassivation behavior of chromate conversion coatings leads to protection from corrosion resulting from mechanical damage. The nature of this repassivation has been explored here using Raman spectroscopy and synchrotron X-ray absorption near-edge structure (XANES) spectroscopy. Raman spectroscopic analysis of a mechanically damaged area on the CCC supports the theory of chromium ion migration and formation of an Al(III)-Cr(VI) complex at the active sites. Results of an investigation performed using XANES corroborate the formation of the complex at active sites such as pits/valleys/scratches even under other chromating conditions. This study therefore provides unambiguous evidence for the theory of migration of chromates. © 2004 The Electrochemical Society. All rights reserved.
Electrochemical/Chemical Deposition and Etching
C91
Jie Gong and Giovanni Zangari
Small amounts of metal ions
or
added to an electrolyte for Mn electrodeposition increase the metallic character of amorphous Mn coatings grown at high current densities. The codeposited oxygen decreases from 54 atom % to less than 7 atom %, while the codeposited Sn or Cu are below 1 and 3 atom %, respectively. The resulting amorphous coatings exhibit very different mechanical properties and better corrosion resistance than those of amorphous manganese coatings electrodeposited without metal ion additives. © 2004 The Electrochemical Society. All rights reserved.
C95
S. K. Seol, J. M. Yi, X. Jin, C. C. Kim, J. H. Je, W. L. Tsai, P. C. Hsu, Y. Hwu, C. H. Chen, L. W. Chang et al
Localized electrochemical deposition (LECD) is an emerging technology for inexpensive and effective fabrication of high-aspect-ratio microstructure of diverse materials. Microradiology with coherent X-rays enabled study of this process in real-time. This led to the discovery of a fundamental role of the microelectrode-structure distance: for short distances the deposition rate increases dramatically but the product becomes porous. This role is explained qualitatively with the interplay between metal-ion diffusion and migration in the deposition process. © 2004 The Electrochemical Society. All rights reserved.
C98
Soo-Kil Kim and Jae Jeong Kim
Interesting phenomena were observed during an investigation on the accelerating effects of 3-mercapto-1-propane sulfonic acid (MPSA), i.e., different aging times of MPSA result in different filling profiles. When MPSA was added to the electrolyte immediately before electrodeposition, subconformal deposits appeared, whereas MPSA aged over 12 h enabled superfilling. From UV-visible analysis, over 99% MPSA was converted to bis(3-sulfopropyl)disulfide (SPS) within 12 h through the reaction with
which means that SPS was, in terms of “visible” superfilling, the real accelerator. This arose from the fact that SPS experienced adsorption first, while MPSA underwent
reduction first at the trench entrance. © 2004 The Electrochemical Society. All rights reserved.
C101
Soo-Kil Kim and Jae Jeong Kim
To avoid complications brought about by employing organic additives, microcontact printing using a flat stamp was used in forming trench-selective Cu superfilling on damascene structure. Self-assembled monolayers of 1-decanethiol transferred on top surface of the trench could withstand the
electrolyte and were used as a barrier for current transfer below a certain potential that was not yet dominated by the tunneling current. Subsequent electrodeposition on the printing area was successfully inhibited. The resulting filling profile was a defect-free superfilling with bumps on top. This is comparable to the three-additive system consisting of accelerator and two-component suppressor. © 2004 The Electrochemical Society. All rights reserved.
C104
Ying Wang, Changchun Zhu, Ying Li and Chunyu Wu
An improved approach of wet isotropic etching of silicon wafers to obtain two-level microstructures is presented. Etching behavior of silicon with nitride/oxide mask in an acid-based etchant was studied. The shape and size of the etched trench depended mostly on the mask window size. By designing a mask and etching process correctly, the desired position and depth of an individual level could be obtained with only one masking step. This technology was a significant improvement in silicon isotropic etching technology and is expected to be used widely in semiconductor devices. © 2004 The Electrochemical Society. All rights reserved.
C107
Yibin Zhang, Long Huang, Tiruchirapalli N. Arunagiri, Oscar Ojeda, Sarah Flores, Oliver Chyan and Robert M. Wallace
Electrochemical Synthesis and Engineering
D11
Y.-K. Liu, C. Scheck, R. Schad and G. Zangari
We report epitaxial growth of Fe thin films on both n-type GaAs(001) and GaAs(011) substrates using electrochemical deposition. The structural quality depends on the composition of the plating solution. The magnetic properties are characterized by fourfold crystalline anisotropy for the Fe(001) film while for the Fe(011) layers we observe a uniaxial anisotropy induced by the substrate asymmetry. The in-plane coercivity is around 30-100 Oe. © 2004 The Electrochemical Society. All rights reserved.
Physical and Analytical Electrochemistry
E35
Zhiqiang Gao and Zhongxing Jiang
Self-assembled monolayer anthraquinone-polyethers on gold electrodes were prepared and characterized by various spectroscopic and electrochemical techniques. The monolayers exhibited better thermal stability in solution, suggesting that multianchoring effects of disulfide moieties improve the integrated adhesion and binding stability of the monolayers. In contrast to solution electrochemistry, the unique structure and packing of the monolayer lead to selective ion binding to ions with the right size and charge, such as potassium and sodium. © 2004 The Electrochemical Society. All rights reserved.
Dielectric Science and Materials
F49
Q. T. Le, C. M. Whelan, H. Struyf, H. Bender, T. Conard, S. H. Brongersma, W. Boullart, S. Vanhaelemeersch and K. Maex
Semiconductor Devices, Materials, and Processing
G179
Jung Inn Sohn, June-O Song, Dong-Seok Leem, Seonghoon Lee and Tae-Yeon Seong
The effects of the insertion of Au nanodots (4-10 nm in diameter) at the Ni/GaN interface on the electrical properties of Ni/Au ohmic contacts to p-type GaN have been investigated. As-deposited Ni/Au contacts with Au nanodots show better electrical behavior than contacts without Au nanodots. Nanodot contacts produce a specific contact resistance of
The multiquantum-well light-emitting diodes (LEDs) are fabricated with the nanodot Ni/Au contact layers. Nanodot LEDs show a lower operating voltage compared with LEDs made with a conventional Ni/Au contact layer. © 2004 The Electrochemical Society. All rights reserved.
G182
J. D. Lim, K. S. Suh, S. B. Shim, C. R. Abernathy, S. J. Pearton, R. G. Wilson and Y. D. Park
G185
Jung Wook Lim, Sun Jin Yun, Yong Hae Kim, Choong Yong Sohn and Jin Ho Lee
G188
Y. Irokawa, B. Luo, F. Ren, B. P. Gila, C. R. Abernathy, S. J. Pearton, C.-C. Pan, G.-T. Chen, J.-I. Chyi, S. S. Park et al
G192
S. Kishino, H. Yoshida and N. Kitai
A novel gettering technique for a thin silcon-on-insulator (SOI) wafer is proposed. The gettering procedure for 1 h at 600°C using polycrystalline silicon film is followed by protection of the device region where the film is immediately removed after the procedure from the SOI wafer. Gettering was evaluated by comparing electrical properties of devices in gettered and ungettered parts of the wafer where half of the wafer was gettered. A detectable reduction of an off-current was observed in the gettered parts. The gettering effect was supported by the reduction of the localized state density measured by the charge pumping method. © 2004 The Electrochemical Society. All rights reserved.
G195
Soo-Hyun Kim, Eui-Sung Hwang, Sang-Yup Han, Seung-Ho Pyi, Nohjung Kawk, Hyunchul Sohn, Jinwoong Kim and Gi Bo Choi
G198
Y. N. Tan, W. K. Chim, B. J. Cho and W. K. Choi
Sensors and Displays: Principles, Materials, and Processing
H33
Jung Wook Lim and Sun Jin Yun
H36
T. Karabacak, C. Wiegand, J. Senkevich, T. Lu, Dongdong Jia and F. Fernandez
A Si substrate was coated with a 100 nm thick tungsten nanocolumns base layer through glancing-angle magnetron-sputtering deposition. 50 nm thick poly(p-phenylene vinylene) (PPV) polymer thin films were deposited onto the tungsten nanocolumns base layer coated Si substrate and flat tungsten base layer coated Si substrate through chemical vapor deposition. The photoluminescence of the PPV thin films were studied. Both photoluminescence emission and absorption intensity were seen amplified through the deposition on the Si substrate with the tungsten nanocolumns base layer. The enhanced photoluminescence originated from the increasing PPV surface area, and the excitation and emission cross sections. © 2004 The Electrochemical Society. All rights reserved.
General Topics
J33
Xueming Chen and Guohua Chen
J36
Wen-Yuan Liu, Zheng-Wen Fu, Chi-Lin Li and Qi-Zong Qin
Lithium phosphorus oxynitride (Lipon) thin films have been fabricated successfully by nitrogen plasma-assisted deposition of E-beam reactive evaporated
for the first time. The effect of inductively coupled plasma (ICP) powers on the electrical and optical properties of Lipon thin film was investigated. X-ray photoelectron spectra confirmed that the insertion of N into
and N concentration were dependent on ICP powers. Infrared and UV-vis spectrophotometry were used to characterize their optical properties. The electrical properties of the as-deposited Lipon thin films were investigated by impedance spectroscopy and isothermal transient ionic current measurements. © 2004 The Electrochemical Society. All rights reserved.