Batteries, Fuel Cells, and Energy Conversion
A221
Isamu Moriguchi, Fumihiro Nakahara, Hiroshi Furukawa, Hirotoshi Yamada and Tetsuichi Kudo
A224
G. V. Zhuang, K. Xu, T. R. Jow and P. N. Ross Jr.
The chemistry of the solid electrolyte interface (SEI) layer formed on graphite anodes cycled in propylene carbonate (PC)-lithium bis(oxolato)borate (LiBOB) electrolyte was studied by ex situ Fourier transform infrared spectroscopy analysis in the attenuated total reflection mode. The vibrational spectra clearly show that electrochemical reduction of the BOB anion is a part of the SEI layer formation chemistry. The reduction reaction changes the oxygen coordination around the B atom from tetrahedral
to trigonal
e.g., esters of boric acid, and changes the symmetry of the O-C-O bonding closer to that in esters of oxalic acid. © 2004 The Electrochemical Society. All rights reserved.
A228
Yangxing Li, Xiang-Wu Zhang, Saad A. Khan and Peter S. Fedkiw
A231
Masanori Hayase, Takahiko Kawase and Takeshi Hatsuzawa
A fabrication technique of miniature fuel cell electrodes was developed from Si wafers. The fuel channels, porous layer, and catalyst layer were formed in the Si wafer. The fuel channels were fabricated by photolithographic patterning and subsequent wet etching on the Si. The porous layer was formed by anodization of Si from the polymer electrolyte membrane side through the bottom of the fuel channels. Catalyst metals were deposited inside the porous layer by wet plating. The two electrodes were hot-pressed with a Nafion 112 sheet. Open-circuit voltage of 840 mV and maximum power density of
were observed by hydrogen feed. © 2004 The Electrochemical Society. All rights reserved.
A235
G. S. Chen, Gin-Shiang Chen, H. H. Hsiao, R. F. Louh and C. J. Humphreys
A239
Ki Soo Park, Myung Hun Cho, Sung Jang Jin and Kee Suk Nahm
A242
K. M. Begam, M. S. Michael, Y. H. Taufiq-Yap and S. R. S. Prabaharan
A247
Norio Miura, Satomi Oonishi and Kalakodimi Rajendra Prasad
Composite electrodes using activated carbon (AC) and indium tin oxide, ITO (5 wt %
were characterized in 1 M KOH for electrochemical supercapacitors. ITO was prepared by a nitrate decomposition method and reverse precipitation method. A 75% increase in capacitance compared to pristine carbon was observed at
with ITO prepared by the reverse precipitation method. Effect of calcination temperature and the quantity of ITO on the values of capacitance was studied. The increase in capacitance values of AC could be attributed to the higher conductivity and nanosize of ITO powders. Stability of ITO was also examined. © 2004 The Electrochemical Society. All rights reserved.
A250
G. X. Wang, Jane Yao and H. K. Liu
Nanocrystalline Si-mesocarbon microbeads (MCMB) composite anode materials were prepared by ballmilling. Scanning electron microscopic observation showed that the spherical shape of MCMB particles can be retained via moderate ballmilling. Ballmilling conditions have an impact on the capacity and cyclability of nanocrystalline Si-MCMB composites. The optimized Si-MCMB composite anode demonstrated a reversible capacity of 1066 mAh/g with good cyclability. A reaction model has been proposed to explain the reaction mechanisms of lithium insertion and extraction in the Si-MCMB electrode. © 2004 The Electrochemical Society. All rights reserved.
A254
Ted M. Pappenfus, Kent R. Mann and William H. Smyrl
A256
K.-H. Joo, H.-J. Sohn, P. Vinatier, B. Pecquenard and A. Levasseur
Corrosion, Passivation, and Anodic Films
B25
Kai Kamada, Haruto Fukuda, Keita Maehara, Yukiko Yoshida, Masumi Nakai, Shunji Hasuo and Yasumichi Matsumoto
B29
S. D. Reeves and R. Scott Morris
The modification of mesocarbon microbeads (MCMB) anodes with nonionic surfactants for secondary lithium batteries is described. The surfactant treatment drastically improves the wettability of MCMB anodes and inhibits passivation from solid electrolyte interface formation. The surface layer resistance for a lithiated MCMB anode that was treated with surfactant was identical to the surface layer resistance for an unlithiated MCMB anode. In addition, the treatment also resulted in a much lower charge-transfer resistance and yielded batteries which exhibit faster charging and improved cycle life. © 2004 The Electrochemical Society. All rights reserved.
Electrochemical/Chemical Deposition and Etching
C81
H. Matsushima, T. Nohira and Y. Ito
The surface morphology of iron thin films galvanostatically electrodeposited in magnetic fields (0.5 T) was observed by atomic force microscopy (AFM). When the magnetic field was superimposed vertically to the copper substrate plane, iron crystal grains became roundish and uniform by the microscopic magnetohydrodynamic convection generated around the grains. In the magnetic field parallel to the substrate, the grains became undulative by the macroscopic magnetohydrodynamic convection generated in a parallel direction to the cathode surface. © 2004 The Electrochemical Society. All rights reserved.
C84
N. Saito, R. Ohta, K. H. Lee, Y. Kobayashi, S. Okazaki, Y. Inoue, H. Sugimura and O. Takai
C87
Jin-Seong Park and Sang-Won Kang
Dielectric Science and Materials
F45
Jung Wook Lim and Sun Jin Yun
Semiconductor Devices, Materials, and Processing
G151
Yeo-Geon Yoon, Byoung-Dong Kim, Min-Sun Kim, Seong-Hee Choi and Seung-Ki Joo
G154
R. Chan, T. N. Arunagiri, Y. Zhang, O. Chyan, R. M. Wallace, M. J. Kim and T. Q. Hurd
Diffusion studies were carried out on physical vapor deposited Cu/Ru(∼20 nm)/Si samples using secondary ion mass spectroscopy (SIMS) and transmission electron microscopy (TEM). Back side SIMS depth profiling revealed well-defined interfaces and showed that Cu interdiffusion was impeded by Ru thin film up to 450°C vacuum annealing. TEM showed a 20-22 nm Ru barrier layer with a columnar microstructure oriented vertically with respect to Si substrate. TEM results corroborate with SIMS data to indicate stability of the Ru film barrier for annealing temperatures up to 450°C. Direct Cu electroplating on ultrathin Ru barrier layers (<20 nm) was investigated in sulfuric acid. The electroplated Cu film is shiny, smooth, and without agglomeration under scanning electron microscopy. Excellent adhesion between interfacial layers was confirmed by the scribe-peel test. The interfacial characterization results indicate that Ru thin film is a promising candidate as a directly plateable Cu diffusion barrier. © 2004 The Electrochemical Society. All rights reserved.
G158
Toshiro Doi, Ara Philipossian and Koichiro Ichikawa
A controlled atmosphere polisher (CAP) was manufactured featuring a pressure-resistant chamber that hermetically contains the entire processing unit. The machine allows chamber gases to be changed. A vacuum pump or a compressor is used to maintain chamber pressure at a desired set point. When polishing under an air ambient, polish rates under partial vacuum or under pressurized conditions are significantly higher than those under conventional polishing conditions. Differences in polish rate are also seen depending on the type of gas used during polishing. This polishing method and tool have the potential of efficiently controlling and enhancing silicon polish rates. © 2004 The Electrochemical Society. All rights reserved.
G161
Giovanni Mannino, Vittorio Privitera, Silvia Scalese, Sebania Libertino, Enrico Napolitani, Peter Pichler and Nicholas E. B. Cowern
Nitrogen implants were performed in Si wafers of variable purity, i.e., epitaxial layers, float zone, and Czochralski silicon (CZ-Si). The diffusion behavior of nitrogen reported by Hockett in Appl. Phys. Lett., 54, 1793 (1989), where nitrogen diffuses for several micrometers at temperatures as low as 750°C and the profiles assume a “double-peak” structure, is peculiar of CZ-Si. In contrast, in pure epitaxial-Si, nitrogen is immobile at low temperature but, at a higher temperature (850°C), the broadening of the nitrogen profile never assumes the shape observed in CZ-Si. Our results suggest that oxygen determines the shape of the nitrogen diffusion profiles. © 2004 The Electrochemical Society. All rights reserved.
G164
Jeff J. Peterson, Chadwin D. Young, Joel Barnett, Sundar Gopalan, Jim Gutt, Choong-Ho Lee, Hong-Jyh Li, Tuo-Hung Hou, Yudong Kim, Chan Lim et al
G168
D. Starosvetsky, M. Kovler and Y. Ein-Eli
High dissolution rates
of both n- and p-type silicon (〈100〉) were obtained by a novel process of wet silicon etching utilizing cathodic bias. This etching process results in very smooth silicon surfaces. Unlike custom wet etching, conducted in strong alkaline or in hydrofluoric acid solutions, this method is performed even in neutral solutions. A possible mechanism for Si negative potential dissolution in alkaline solutions is discussed. © 2004 The Electrochemical Society. All rights reserved.
G172
Xuanxiong Zhang and Jean-Pierre Raskin
G175
S. Balakumar, Tohru Hara, Rakesh Kumar, Takamasa Wakabayashi and Minoru Uchida
The properties of Cu seed layers deposited on Zr-based diffusion barriers, TiZr and TiZrN, are described. Stress and resistivity of the seed and electroplated (EP) films deposited on the barriers show better performance as compared to Cu layers deposited on a TaN barrier. Cu diffusivity in TiZrN is less than TiZr and TaN when annealed at 400°C for 10 min. Chemical mechanical planarization (CMP) compatibility using Cu and barrier slurries were also carried out. Adhesion strength of EP Cu deposited on TiZr was higher as compared to EP Cu on TiZrN. The critical pressure for CMP of Zr-based barriers is higher in abrasive-free slurry as compared to abrasive slurry. © 2004 The Electrochemical Society. All rights reserved.
Sensors and Displays: Principles, Materials, and Processing
H27
Kazuyuki Nishio and Hideki Masuda
The dependence of the transmission properties of metal hole array prepared by a two-step molding process using porous alumina on the refractive index of the medium embedded in the holes was examined. A metal hole array membrane was set in a cell containing aqueous solutions with different refractive indices depending on their concentrations. The peak wavelength of the transmission spectra of the hole array showed a good linear relationship with the refractive index of the medium. Such unique optical properties will be useful in the application of the metal hole arrays to spectroelectrochemical analysis combined with electrochemical application. © 2004 The Electrochemical Society. All rights reserved.
H29
Jung-Hsien Yen, Ing-Chi Leu, Min-Tao Wu, Chien-Chih Lin and Ming-Hsiung Hon
General Topics
J27
Renyun Zhang, Xuemei Wang and Shenjing Gong
The binding of anticancer drug dacarbazine (DTIC) to DNA bases in the absence and presence of Au nanoparticles has been explored by electrochemical study. The results indicate that the binding of purines (adenine and guanine) to DTIC is stronger than that of pyrimidines (thymine and cytosine) in the order of
It was also observed that the presence of gold nanoparticles could facilitate the specific interaction between DTIC with DNA bases. © 2004 The Electrochemical Society. All rights reserved.
J29
Moonjung Kim, Soo-Kun Jeon and Young-Se Kwon
An approach for fabricating a self-aligned InP/InGaAs heterojunction bipolar transistor (HBT) with InGaAs dummy emitter layer was demonstrated. The self-aligned emitter-base structure employs crystallographically defined emitter contact (CDC) technology to define a desired emitter-to-base contact spacing. An anisotropic wet etching of the InGaAs dummy emitter layer grown on the HBT layer structure leads to the crystallographically etched profiles to configure the shape of the emitter contact. InP/InGaAs HBTs demonstrated good current-voltage characteristics with a current gain more than 40 and a knee voltage of approximately 0.5 V up to a collector current density of
indicating the effectiveness of the new self-alignment technology. © 2004 The Electrochemical Society. All rights reserved.