Topical Reviews
072001
Chenggen Wu, Xun Zhang, Rui Wang, Li Jun Chen, Meng Nie, Zhiqiang Zhang, Xiaodong Huang and Lei Han
Wearable sensors are believed to be the most important part of the Internet of Things. In order to meet the application requirements, low-dimensional materials such as graphene and carbon nanotubes have been attempted to constitute wearable sensors with high performance. Our discussions in this review include the different low-dimensional material based sensors which are employed in wearable applications. Low-dimensional materials based wearable sensors for detecting various physical quantities in surroundings, including temperature sensor, pressure or strain sensor and humidity sensor, is introduced. The primary objective of this paper is to provide a comprehensive review of research status and future development direction of low-dimensional materials based wearable sensors. Challenges for developing commercially low-dimensional namomaterials based wearable sensors are highlighted as well.
072002
Shilin Li, Hong Zhang, Shengli Yue, Xi Yu and Huiqiong Zhou
Solution-processed organic photovoltaic (OPV) as a new energy device has attracted much attention due to its huge potential in future commercial manufacturing. However, so far, most of the studies on high-performance OPV have been treated with halogenated solvents. Halogenated solvents not only pollute the environment, but are also harmful to human health, which will negatively affect the large-scale production of OPV in the future. Therefore, it is urgent to develop low-toxic or non-toxic non-halogen solvent-processable OPV. Compared with conventional fullerene OPVs, non-fullerene OPVs exist with stronger absorption, better-matched energy levels and lower energy loss. Processing photoactive layers with non-fullerenes as the acceptor material has broad potential advantages in non-halogenated solvents. This review introduces the research progress of non-fullerene OPV treated by three different kinds of green solvents as the non-halogenated and aromatic solvent, the non-halogenated and non-aromatic solvent, alcohol and water. Furthermore, the effects of different optimization strategies on the photoelectric performance and stability of non-fullerene OPV are analyzed in detail. The current optimization strategy can increase the power conversion efficiency of non-fullerene OPV processed with non-halogen solvents up to 17.33%, which is close to the performance of processing with halogen-containing solvents. Finally, the commercial potential of non-halogen solvent processing OPVs is discussed. The green solvent processing of non-fullerene-based OPVs will become a key development direction for the future of the OPV industry.
072003
Guangxin Xue, Linlin Yin, Shengxian Shao and Guodong Li
Phenol is considered as an important platform molecule for synthesizing value-added chemical intermediates and products. To date, various strategies for phenol transformation have been developed, and among them, selective hydrogenation of phenol toward cyclohexanone (K), cyclohexanol (A) or the mixture KA oil has been attracted great interest because they are both the key raw materials for the synthesis of nylon 6 and 66, as well as many other chemical products, including polyamides. However, until now it is still challengeable to realize the industrilized application of phenol hydrogenation toward KA oils. To better understand the selective hydrogenation of phenol and fabricate the enabled nanocatalysts, it is necessary to summarize the recent progress on selective hydrogenation of phenol with different catalysts. In this review, we first summarize the selective hydrogenation of phenol toward cyclohexanone or cyclohexanol by different nanocatalysts, and simultaneously discuss the relationship among the active components, type of supports and their performances. Then, the possible reaction mechanism of phenol hydrogenation with the typical metal nanocatalysts is summarized. Subsequently, the possible ways for scale-up hydrogenation of phenol are discussed. Finally, the potential challenges and future developments of metal nanocatalysts for the selective hydrogenation of phenol are proposed.
072004
Suma Das and Avijit Chowdhury
Heterogeneous photocatalysis premised on advanced oxidation processes has witnessed a broad application perspective, including water purification and environmental remediation. In particular, the graphitic carbon nitride (g-C3N4), an earth-abundant metal-free conjugated polymer, has acquired extensive application scope and interdisciplinary consideration owing to its outstanding structural and physicochemical properties. However, several issues such as the high recombination rate of the photo-generated electron–hole pairs, smaller specific surface area, and lower electrical conductivity curtail the catalytic efficacy of bulk g-C3N4. Another challenging task is separating the catalyst from the reaction medium, limiting their reusability and practical applications. Therefore, several methodologies are adopted strategically to tackle these issues. Attention is being paid, especially to the magnetic nanocomposites (NCs) based catalysts to enhance efficiency and proficient reusability property. This review summarizes the latest progress related to the design and development of magnetic g-C3N4-based NCs and their utilization in photocatalytic systems. The usefulness of the semiconductor heterojunctions on the catalytic activity, working mechanism, and degradation of pollutants are discussed in detail. The major challenges and prospects of using magnetic g-C3N4-based NCs for photocatalytic applications are highlighted in this report.
Papers
Biology and medicine
075101
Fan Li, Huiquan Yang, Yuyu Cao, Dongdong Li, Jing Ma and Peidang Liu
The combination of multiple therapies has been proved to be more effective than a single therapy for many cancers. This study aimed to investigate the synergistic antibreast cancer effect of doxorubicin-loaded silver nanotriangles (DOX-AgNTs) combined with near-infrared (NIR) irradiation and explore the underlying mechanism. AgNTs were prepared by a chemical method and DOX was loaded via electrostatic adsorption. Characterization was performed by transmission electron microscopy, ultraviolet–visible spectroscopy and dynamic light scattering. The viability of MDA-MB-231 cells was detected by using MTT assay to evaluate the synergistic anticancer effect of DOX-AgNTs combined with NIR irradiation. The intracellular reactive oxygen species (ROS) level and cell apoptosis were analyzed by flow cytometry. Mitochondrial membrane potential (MMP) was measured with fluorescence microscopy. The mechanism was further investigated with ROS scavenger N-acetylcysteine and specific inhibitors of extracellular signal-regulated kinase 1/2 (ERK1/2), C-jun N-terminal kinase and p38 pathways. Characterization results revealed that the prepared AgNTs were mostly triangular and the mean edge length was about 126 nm. The combination of DOX-AgNTs and NIR exhibited a superior synergistic anticancer effect over single DOX-AgNTs or photothermal therapy (PTT). N-acetylcysteine and ERK1/2 inhibitor U0126 were found to significantly rescue the decreased cell viability, declined MMP and increased apoptosis induced by the combined treatment. Our results suggested that DOX-AgNTs combined with PTT performed a synergistic antibreast cancer effect. The synergy might be closely associated with the excessive production of ROS, changed MMP and the activation of ERK1/2 signaling pathway. These findings might provide a new perspective for the development of breast cancer treatments with excellent efficacy.
075102
Bahar Nikforouz, Alireza Allafchian, Seyed Amir Hossein Jalali, Hamideh Shakeripour and Rezvan Mohammadinezhad
This study investigates the potential of iron oxide nanoparticles (Fe3O4) and quince seed mucilage as combined genetic carriers to deliver plasmid DNA (pDNA) through the gastrointestinal system. The samples are characterized by x-ray diffraction (XRD), zeta potential, dynamic light scattering, FT-IR spectroscopy, field emission scanning electron microscopy and vibrating sample magnetometry. The stability of pDNA loading on the nanocarriers and their release pattern are evaluated in simulated gastrointestinal environments by electrophoresis. The XRD patterns reveal that the nanocarriers could preserve their structure during various synthesis levels. The saturation magnetization (Ms) of the Fe3O4 cores are 56.48 emu g−1 without any magnetic hysteresis. Not only does the loaded pDNA contents experience a remarkable stability in the simulated gastric environment, but also, they could be released up to 99% when exposed to an alkaline environment similar to the intestinal fluid of fish. The results indicate that the synthesized nanoparticles could be employed as efficient low-cost pDNA carriers.
075103
Elham Rashidi, Neda Esfandiari, Zahra Ranjbar, Nikta Alvandi and Zahra Fatahi
During recent years, cancer has been recognized as a well-known disorder all over the world. One of the important factors to tackle this problem better than past decades is early diagnosis that takes into practice by state-of-the-art visual equipment for detection cancer cells. Herein, in this research, we synthesized carbon dots with pH-dependent behavior from a green source by hydrothermal method with high quantum yield and blue fluorescence. Folic acid-conjugated carbon dots by an efficient and optimal conjugation method were set upped which determined cancer cells visually. These synthesized and conjugated nanoparticles entered into the cancer cells more comprehensive than normal cells by receptor-mediated endocytosis and could distinguish cancer cells from normal ones by fluorescence imaging. Ultimately, synthesized nanoparticles in this research can be considered as an efficient fluorescent nanoprobe for cancer pre-diagnosis.
075104
Pardis Moradi, Akbar Hasanzadeh, Fatemeh Radmanesh, Saideh Rajai Daryasarei, Elaheh Sadat Hosseini, Jafar Kiani, Ali Shahbazi, Helena Nourizadeh, Maryam Eslami, Akbar Dorgalaleh et al
An efficient and safe delivery system for the transfection of CRISPR plasmid (p/CRISPR) into target cells can open new avenues for the treatment of various diseases. Herein, we design a novel nonvehicle by integrating an arginine-disulfide linker with low-molecular-weight PEI (PEI1.8k) for the delivery of p/CRISPR. These PEI1.8k-Arg nanoparticles facilitate the plasmid release and improve both membrane permeability and nuclear localization, thereby exhibiting higher transfection efficiency compared to native PEI1.8k in the delivery of nanocomplexes composed of PEI1.8k-Arg and p/CRISPR into conventional cells (HEK 293T). This nanovehicle is also able to transfect p/CRISPR in a wide variety of cells, including hard-to-transfect primary cells (HUVECs), cancer cells (HeLa), and neuronal cells (PC-12) with nearly 5–10 times higher efficiency compared to the polymeric gold standard transfection agent. Furthermore, the PEI1.8k-Arg nanoparticles can edit the GFP gene in the HEK 293T-GFP reporter cell line by delivering all possible forms of CRISPR/Cas9 system (e.g. plasmid encoding Cas9 and sgRNA targeting GFP, and Cas9/sgRNA ribonucleoproteins (RNPs) as well as Cas9 expression plasmid and in vitro-prepared sgRNA) into HEK 293T-GFP cells. The successful delivery of p/CRISPR into local brain tissue is also another remarkable capability of these nanoparticles. In view of all the exceptional benefits of this safe nanocarrier, it is expected to break new ground in the field of gene editing, particularly for therapeutic purposes.
Electronics and photonics
075201
Sheng Lai, Xiaobin Tang, Yunpeng Liu, Junxu Mu, Zhaopeng Feng and Kai Miao
Carbon nanotube (CNT) field-emission x-ray source has great potential in x-ray communication (XCOM) because of its controllable emission and instantaneous response. A novel voltage loading mode was proposed in this work to achieve high-frequency pulse x-ray emission. The characteristics of cathode current and pulse x-ray versus voltage, frequency, and pulse amplitude were studied, and XCOM data transmission experiment was carried out. Results showed that the CNT cold cathode x-ray source, as a communication signal source, could work in 1.05 MHz pulse emission frequency. When the grid voltage was higher than 470 V, the pulse x-ray waveform amplitude achieved peak, and the shape exhibited a pseudo square wave. The duty cycle of the x-ray waveform exceeded 50%, reaching 56% when the pulse frequency reached 1 MHz. In the XCOM data transmission experiment, the pulsed x-ray waveform was well consistent with the loading data signal voltage waveform under different pulse-emission frequencies. This work realized the x-ray high-frequency pulse emission of CNT cold cathode x-ray source and lays a foundation for the development and application of CNT cold cathode x-ray source in XCOM.
075202
The following article is Open access
Zhongyunshen Zhu, Johannes Svensson, Adam Jönsson and Lars-Erik Wernersson
GaSb is considered as an attractive p-type channel material for future III-V metal-oxide-semiconductor (MOS) technologies, but the processing conditions to utilize the full device potential such as low power logic applications and RF applications still need attention. In this work, applying rapid thermal annealing (RTA) to nanoscale GaSb vertical nanowire p-type MOS field-effect transistors, we have improved the average peak transconductance (gm,peak) by 50% among 28 devices and achieved 70 μS μm−1 at VDS = −0.5 V in a device with 200 nm gate length. In addition, a low subthreshold swing down to 144 mV dec−1 as well as an off-current below 5 nA μm−1 which refers to the off-current specification in low-operation-power condition has been obtained. Based on the statistical analysis, the results show a great enhancement in both on- and off-state performance with respect to previous work mainly due to the improved electrostatics and contacts after RTA, leading to a potential in low-power logic applications. We have also examined a short channel device with Lg = 80 nm in RTA, which shows an increased gm,peak up to 149 μS μm−1 at VDS = −0.5 V as well as a low on-resistance of 4.7 kΩ·μm. The potential of further enhancement in gm via RTA offers a good alternative to obtain high-performance devices for RF applications which have less stringent requirement for off-state performance. Our results indicate that post-fabrication annealing provides a great option to improve the performance of GaSb-based p-type devices with different structures for various applications.
075203
Denice N Feria, Sonia Sharma, Yu-Ting Chen, Zhi-Ying Weng, Kuo-Pin Chiu, Jy-Shan Hsu, Ching-Ling Hsu, Chi-Tsu Yuan, Tai-Yuan Lin and Ji-Lin Shen
Understanding the mechanism of the negative differential resistance (NDR) in transition metal dichalcogenides is essential for fundamental science and the development of electronic devices. Here, the NDR of the current–voltage characteristics was observed based on the glutamine-functionalized WS2 quantum dots (QDs). The NDR effect can be adjusted by varying the applied voltage range, air pressure, surrounding gases, and relative humidity. A peak-to-valley current ratio as high as 6.3 has been achieved at room temperature. Carrier trapping induced by water molecules was suggested to be responsible for the mechanism of the NDR in the glutamine-functionalized WS2 QDs. Investigating the NDR of WS2 QDs may promote the development of memory applications and emerging devices.
075204
The following article is Open access
Shichao Sun, Zhihong Wang, Suci Meng, Rui Yu, Deli Jiang and Min Chen
It is still a huge challenge to develop highly efficient and low-cost non-precious metal-based electrocatalysts for overall water splitting in alkaline electrolytes. Herein, Cr and Fe co-doped CoP porous mesh nanosheets (Mesh-CrFe-CoP NSs) were synthesized through hydrolysis reaction, ion exchange etching and subsequent low-temperature phosphating process. The Mesh-CrFe-CoP NSs provides overpotentials at a current density of 10 mA cm−2 under alkaline electrolyte of 103.7 mV and 256.4 mV for HER and OER, respectively. Furthermore, when using Mesh-CrFe-CoP NSs as anode and cathode, the water splitting system could afford a current density of 10 mA cm–2 at 1.55 V, which is better than an electrolytic cell composed of 20% Pt/C and RuO2. The excellent electrocatalytic performance of Mesh-CrFe-CoP NSs is attributed to the co-doping and porous nanostructure. Specifically, the Cr and Fe co-doped porous CoP nanosheets electrocatalyst not only provided abundant exposure active sites, accelerated the entry of liquid and the diffusion of gas, but also regulated the electronic environment of active sites, and thus enhanced the electrochemical performance. This work proposes a strategy for the rational design of highly efficient and stable non-precious metal co-doped phosphide electrocatalysts in the of electrochemical water splitting.
075205
Muhammad Nawaz Sharif, Muhammad Usman, Mussaab Ibrahim Niass, Juin J Liou, Fang Wang and Yuhuai Liu
The electron blocking layer (EBL) plays a vital role in blocking the electron overflow from an active region in the AlGaN-based deep-ultraviolet light-emitting diode (DUV-LED). Besides the blocking of electron overflow, EBL reduces hole injection toward the active region. In this work, we proposed a DUV nanowire (NW) LED structure without EBL by replacing it with a compositionally continuous graded hole source layer (HSL). Our proposed graded HSL without EBL provides a better electron blocking effect and enhanced hole injection efficiency. As a result, optical power is improved by 48% and series resistance is reduced by 50% with 4.8 V threshold voltage. Moreover, graded HSL without EBL offer reduced electric field within the active region, which leads to a significant increment in radiative recombination rate and enhancement of spontaneous emission by 34% at 254 nm wavelength, as a result, 52% maximum internal quantum efficiency with 24% efficiency drop is reported.
075206
Yuning Li, Shasha Li, Jingye Sun, Ke Li, Zewen Liu and Tao Deng
Unlike zero-bandgap graphene, molybdenum disulfide (MoS2) has an adjustable bandgap and high light absorption rate, hence photodetectors based on MoS2 have attracted tremendous research attention. Most of the reported MoS2 photodetectors adopted back-gate field-effect transistor (FET) structure due to its easy fabrication and modulation features. However, the back-gate FET structure requires very high gate voltage up to 100 V, and it is impossible to modulate each device in an array with this structure independently. This work demonstrated a monolayer MoS2 photodetector based on a buried-gate FET structure whose experimental results showed that both the electrical and photoelectrical properties could be well modulated by a gate voltage as low as 3 V. A photoresponsivity above 1 A W−1 was obtained under a 395 nm light-emitting diode light illumination, which is over 2 orders of magnitude higher than that of a reported back-gate photodetector based on monolayer MoS2 (7.5 mA W−1). The photoresponsivity can be further improved by increasing the buried gate voltage and source-drain voltage. These results are of significance for the practical applications of MoS2 photodetectors, especially in the low voltage and energy-saving areas.
075207
Marian Baah, Afifa Rahman, Sarah Sibilia, Gianmarco Trezza, Luigi Ferrigno, Laura Micheli, Antonio Maffucci, Ekaterina Soboleva, Yuri Svirko and Polina Kuzhir
In this paper we propose an original approach for the real-time detection of industrial organic pollutants in water. It is based on the monitoring of the time evolution of the electrical impedance of low-cost graphitic nanomembranes. The developed approach exploits the high sensitivity of the impedance of 2D graphene-related materials to the adsorbents. We examined sensitivity of the nanomembranes based on pyrolyzed photoresist, pyrolytic carbon (PyC), and multilayer graphene films. In order to realize a prototype of a sensor capable of monitoring the pollutants in water, the membranes were integrated into an ad hoc printed circuit board. We demonstrated the correlation between the sensitivity of the electric impedance to adsorbents and the structure of the nanomembranes, and revealed that the amorphous PyC, being most homogeneous and adhesive to the SiO2 substrate, is the most promising in terms of integration into industrial pollutants sensors.
075208
Alexander Vokhmintsev, Ilya Petrenyov, Robert Kamalov and Ilya Weinstein
The prospects of the development of non-volatile memory elements that involve memristive metal-dielectric-metal sandwich structures are due to the possibility of reliably implementing sustained functional states with quantized conductance. In the present paper, we have explored the properties of Zr/ZrO2/Au memristors fabricated based on an anodic zirconia layer that consists of an ordered array of vertically oriented non-stoichiometric nanotubes with an outer diameter of 30 nm. The operational stability of the designed memory devices has been analyzed in unipolar and bipolar resistive switching modes. The resistance ratio ≥105 between high-resistance (HRS) and low-resistance (LRS) states has been evaluated. It has been found that the LRS conductivity is quantized over a wide range with a fundamental minimum of 0.5G0 = 38.74 μS due to the formation of quantum conductors based on oxygen vacancies (VO). For Zr/ZrO2/Au memristors, resistive switching mechanisms to be sensitive to the migration of VO in an applied electric field have been proposed. It has been shown that the ohmic type and space-charge-limited conductivities are realized in the LRS and HRS, respectively. Besides, we have offered a brief review of parameters for functional metal/zirconia/metal nanolayered structures to create effective memristors with multiple resistive states and a high resistance ratio.
Patterning and nanofabrication
075301
Shao-Fu Chang, Xuan Zhou, Shih-Hsun Chen and Yao-Hsuan Tseng
Lead (Pb) nanowire arrays were fabricated with anodic aluminum oxide (AAO) templates of 30, 100 and 300 nm in pore diameters. Through vacuum injection molding process, Pb/AAO composite was obtained, and lead sulfide (PbS) could further be synthesized after exposing to sulfur gas. AAO templates with different pore sizes were fabricated by using pure aluminum in a two-step anodization. Three types of solutions, which are 10 vol% sulfuric acid, 3 wt% oxalic acid and 1 vol% phosphoric acid, were adopted to achieve AAO of various pore sizes. Different sulfurization temperatures and time spans were applied for studying on the formation mechanism of PbS. Finally, the morphology, composition, structure and elements distribution of the as-prepared Pb and PbS nanowires were confirmed through the use of scanning electron microscopy, energy dispersive x-ray spectroscopy, element-mapping, x-ray diffraction and transmission electron microscopy analysis. The results indicated that Pb nanowires were successfully obtained after applying vacuum injection molding process with 50 kgf cm−2 hydraulic pressure, and PbS nano arrays can be formed by sulfurization at 500 °C for 5 h. Furthermore, an optical property, ultraviolet–visible (UV–Vis) absorption, was also measured. The measurement of the PbS nanowires showed that a significant quantum confinement effect made the energy gap produce a blue shift from 0.41 eV to 1.65 eV or 1.72 eV.
075302
Alireza Allafchian, Shiva Saeedi and Seyed Amir Hossein Jalali
Synthesis of Balangu (Lallemantia royleana) seed mucilage (BSM) solutions combined with polyvinyl alcohol (PVA) was studied for the purpose of producing 3D electrospun cell culture scaffolds. Production of pure BSM nanofibers proved to be difficult, yet integration of PVA contributed to a facile and successful formation of BSM/PVA nanofibers. Different BSM/PVA ratios were fabricated to achieve the desired nanofibrous structure for cell proliferation. It is found that the optimal bead-free ratio of 50/50 with a mean fiber diameter of ≈180 nm presents the most desirable scaffold structure for cell growth. The positive effect of PVA incorporation was approved by analyzing BSM/PVA solutions through physiochemical assays such as electrical conductivity, viscosity and surface tension tests. According to the thermal analysis (TGA/DSC), incorporation of PVA enhanced thermal stability of the samples. Successful fabrication of the nanofibers is verified by FT-IR spectra, where no major chemical interaction between BSM and PVA is detected. The crystallinity of the electrospun nanofibers is investigated by XRD, revealing the nearly amorphous structure of BSM/PVA scaffolds. The MTT assay is employed to verify the biocompatibility of the scaffolds. The cell culture experiment using epithelial Vero cells shows the affinity of the cells to adhere to their nanofibrous substrate and grow to form continuous cell layers after 72 h of incubation.
075303
Lei Sun, Helin Zou and Shengbo Sang
Nano-mold is an essential tool for nano-imprinting. However, large-area nano-mold fabrication relies on expensive equipment or complicated processing. Silicon nano-molds were achieved by proximity ultraviolet lithography and reactive ion etching (RIE). By optimizing the parameters in the processes of exposure, development, and RIE, silicon nano-mold with nano-scale ridges were fabricated with high-precision. The achieved minimum width of nano-ridges was 263 nm. This method is capable of fabricating silicon nano-mold covering four-inch wafer, which is simple, efficient and free from costly equipment.
Energy at the nanoscale
075401
Bo-Qiang Miao, Yi-Ming Liu, Tian-Jiao Wang, Yu Ding and Yu Chen
For the electrochemcial hydrogen production, the oxygen evolution reaction (OER) is a pivotal half-reaction in water splitting. However, OER suffers sluggish kinetics and high overpotential, leading to the increase of overall energy consumption and decrease of the energy efficiency. In this work, high-quality cobalt oxide porous nanotubes (Co3O4-PNTs) are easily obtained by simple self-template approach. One-dimensional (1D) porous structure provides the large specific surface area, enough abundant active atoms and effective mass transfer. In addition, Co3O4-PNTs also own self-stability of 1D architecture, benefitting the their durability for electrocatalytic reaction. Thus, Co3O4-PNTs with optimal annealing temperature and time reveal the attractive alkaline OER performance (Tafel slope of 56 mV dec−1 and 323 mV overpotential at 10 mA cm−2), which outperform the Co3O4 nanoparticles and benchmark commercial RuO2 nanoparticles. Furthermore, Co3O4-PNTs also exhibit excellent OER durability for least 10 h at the 10 mA cm−2. Overall, Co3O4-PNTs with low cost can be serve as a highly reactive and economical catalyst for OER.
075402
Zhanwei Xu, Ying Wang, Mengyu Liu, Muhammad Khaqan Sarwar and Yixing Zhao
A defects-enriched CoMoO4/carbon dot (CD) with CoMoO4 around 37 nm is achieved via hydrothermal reaction by introducing CDs to buffer large volume changes of CoMoO4 during lithiation–delithiation and enhance rate performance. The phase, morphology, microstructure, as well as the interface of the CoMoO4/CD composites were investigated by x-ray diffraction, scanning electron microscopy, transmission electron microscopy and x-ray photoelectron spectroscopy. When employed as Li-ion battery anode, the CoMoO4/CD exhibits a reversible capacity of ∼531 mAh g−1 after 400 cycles at a current density of 2.0 A g−1. Under the scan rate at 2 mV s−1, the CoMoO4/CD shows accounts for 81.1% pseudocapacitance. It may attribute to the CoMoO4 with surface defects given more reaction sites to facilitate electrons and lithium ions transfer at high current densities. Through galvanostatic intermittent titration technique, the average lithium ion diffusion coefficient calculated is an order of magnitude larger than that of bulk CoMoO4, indicating that the CoMoO4/CD possesses promising electrons and lithium ions transportation performance as anode material.
075403
Zhifang Yang, Wenliang Li and Jingping Zhang
It is urgent to explore high-capacity and efficient anode materials for rechargeable lithium-ion batteries. For borophene and phosphorene, two configurations are considered to form a heterojunction: twist angles of 0° (I) and 90° (II). There is a less degree of mismatch and larger formation energy in the formation of a B/P heterojunction, implying that borophene and phosphorene form the stable heterojunction. The heterojunctions of these two configurations demonstrate good conductivity, and the electrons near the Fermi level are mainly provided by borophene. Very importantly, the low energy barrier for interlayer migration of Li is observed in configuration I (0.14eV) and II (0.06 eV), and the migration of Li on the borophene and phosphorene side of the heterojunction still maintains its original energy barrier in bare monolayer. Moreover, the two configurations show the theoretical capacity as high as 738.69 and 721.86 mA h g−1, respectively, which is comparable to bare phosphorene. Furthermore, compared with bare phosphorene, the average voltage is greatly reduced after the formation of heterojunction. Hence, the overall electrochemical properties of the B/P heterojunction have been enhanced by combining the advantages of the individual phosphorene and borophene monolayers, which guarantees the B/P heterojunction as a good candidate for the anode material used in Li-ion batteries.
Sensing and actuating
075501
Amene Naseri and Forough Ghasemi
Visual detection based on gold nanorods (AuNRs) has gained tremendous attention in sensing applications owing to the potential for simple, inexpensive, instrument-free, and on-site detection. The proper selection of the mechanism involved in the interaction between the analyte and the nanostructure plays a significant role in designing a selective and multicolorimetric probe for visual purposes. A winning mechanism to develop multicolorimetric probes is the silver metalization of AuNRs. Herein, an unprecedented idea is presented to expand the variety of multicolorimetric sensors relying on the mechanism of silver deposition. We introduce the anti-silver deposition mechanism in which the analyte directly or indirectly restrains the silver coating of AuNRs. To ascertain the anti-silver deposition mechanism, we have exploited the proposed idea for the direct detection of nitrate. The presence of nitrate (as restrainer agent), which was firstly treated with ascorbic acid (as reducing agent), induced a decrease in the spectral blueshift of AuNRs along with diverse sharp color transitions from reddish-orange (blank) to maroon, wine, berry/purple, dark blue, teal, green, seafoam, and mint. The difference in the spectrum area of the probe in the absent (So) and presence (S) of nitrate were linearly proportional to nitrate concentration in the range of 0.5–5.5 mmol l−1 and the limit of detection was calculated to be 465 μmol l−1. Furthermore, the practicability of the multicolor probe was assessed by the determination of nitrate in complex environmental samples.
075502
Hailong Ma, Lin Jia, Yunan Lin, Huajing Fang, Wenting Wu, Liangliang Wu, Bin Hu and Hong Wang
Transition metal carbides and nitrides (MXenes), as a large family of emerging two-dimensional materials, have demonstrated extraordinary performance in many fields such as electronics, optics and energy storage. However, their susceptibility to oxidation during preparation and storage in ambient air environment is undesirable for long-term and stable applications. Here, we have demonstrated that the spontaneous oxidation of Ti3C2Tx can be harnessed ingeniously to prepare Ti3C2Tx /TiO2in situ formed heterojunctions. Furthermore, a self-powered ultraviolet photodetector was constructed based on the photoelectrochemical performance of Ti3C2Tx /TiO2 heterojunctions. Since the highly conductive Ti3C2Tx can promote the separation and transfer of photogenerated carriers in TiO2, the prepared photodetector exhibits high responsivity (2.06 mA W−1), short rise and decay times (45 and 69 ms) and long-term stability. This work demonstrates the controllable synthesis of Ti3C2Tx/TiO2 heterojunctions and provides a new promising potential of MXenes for photodetection applications.
075503
Yuvaraj Sivalingam, Gabriele Magna, Ramji Kalidoss, Sarathbavan Murugan, David Chidambaram, Venkatramaiah Nutalapati, Surya Velappa Jayaraman, Roberto Paolesse and Corrado Di Natale
The development of electronic noses requires the control of the selectivity pattern of each sensor of the array. Organic chemistry offers a manifold of possibilities to this regard but in many cases the chemical sensitivity is not matched with the response of electronic sensor. The combination of organic and inorganic materials is an approach to transfer the chemical sensitivities of the sensor to the measurable electronic signals. In this paper, this approach is demonstrated with a hybrid material made of phthalocyanines and a bilayer structure of ZnO and TiO2. Results show that the whole spectrum of sensitivity of phthalocyanines results in changes of the resistance of the sensor, and even the adsorption of compounds, such as hexane, which cannot change the resistance of pure phthalocyanine layers, elicits changes of the sensor resistance. Furthermore, since phthalocyanines are optically active, the sensitivity in dark and visible light are different. Thus, operating the sensor in dark and light two different signals per sensors can be extracted. As a consequence, an array of 3 sensors made of different phthalocyanines results in a virtual array of six sensors. The sensor array shows a remarkable selectivity respect to a set of test compounds. Principal component analysis scores plot illustrates that hydrogen bond basicity and dispersion interaction are the dominant mechanisms of interaction.
Materials: synthesis or self-assembly
075601
Maoping Xu, Rui Wang, Kan Bian, Chuang Hou, Yaxing Wu and Guoan Tai
Recently, two-dimensional (2D) boron nanosheets have been predicted to exhibit exceptional physical and chemical properties, which is expected to be widely used in advanced electronics, optoelectronic, energy storage and conversion devices. However, the experimental application of 2D boron nanosheets in hydrogen evolution reactiuon (HER) has not been reported. Here, we have grown ultrathin boron nanosheets on tungsten foils via chemical vapor deposition. The prepared triclinic boron nanosheets are highly crystalline, which perfectly match the structure in the previous theoretical calculations. Notably, the boron nanosheets show excellent HER performance. The Tafel slope is only 64 mV dec−1 and the nanosheets can maintain good stability under long-time cycle in acidic solution. The improvement of performance is mainly due to the metal properties and a large number of exposed active sites on the boron nanosheets, which is confirmed by first-principle calculations.
075602
The following article is Open access
Akito Fukui, Yuki Aoki, Keigo Matsuyama, Hisashi Ichimiya, Ryo Nouchi, Kuniharu Takei, Atsushi Ashida, Takeshi Yoshimura, Norifumi Fujimura and Daisuke Kiriya
Graphene nanoribbon (GNR)-based materials are a promising device material because of their potential high carrier mobility and atomically thin structure. Various approaches have been reported for preparing the GNR-based materials, from bottom-up chemical synthetic procedures to top-down fabrication techniques using lithography of graphene. However, it is still difficult to prepare a large-scale GNR-based material. Here, we develop a procedure to prepare a large-scale GNR network using networked single-layer inorganic nanowires. Vanadium pentoxide (V2O5) nanowires were assembled on graphene with an interfacial layer of a cationic polymer via electrostatic interaction. A large-scale nanowire network can be prepared on graphene and is stable enough for applying an oxygen plasma. Using plasma etching, a networked graphene structure can be generated. Removing the nanowires results in a networked flat structure whose both surface morphology and Raman spectrum indicate a GNR networked structure. The field-effect device indicates the semiconducting character of the GNR networked structure. This work would be useful for fabricating a large-scale GNR-based material as a platform for GNR junctions for physics and electronic circuits.
075603
Jiayi Li, Yu Jin, Yaoqiang Wang, Yilin Zhao and Haijia Su
Sensitive and selective detection of the lead ion (Pb2+) plays an important role in terms of both human health and environmental protection, as the heavy metal is fairly ubiquitous and highly toxic. The highly stable fluorescence biosensor is composed of Fe3O4@TiO2 core–shell nanocomposites, functionalized with a carboxyl fluorescein labeled DNA. The morphology, physical and chemical properties of the sensing nanomaterials were studied by transmission electron microscopy, FT-IR spectroscopy (FT-IR), x-ray powder diffraction and vibrating sample magnetometer. UV–visible and fluorescence spectroscopy were used to characterize the fluorescein functionalized magnetic nanoparticles. The performance of Pb2+ detection displayed an excellent linearity (R2 = 0.995) in the range of 10−10 to 5 × 10−9 ppm with a detection limit of 10−10 ppm, based on the optimization of the fabrication process and aptamers’ specification. The fluorescence biosensor has an accurate response, excellent recoveries and high adsorbent capacities. It was successfully applied for the determination of Pb2+ in contaminated water and serum samples; the detection of limit in both media were 10−10 ppm. These features ensure the potential use of aptamer functionalized magnetic nanocomposites as a new class of non-toxic biocompatible sensors for biological and environmental applications.
075604
Haibin Sun, Shuangshuang Liang, Zijun Xu, Wenrui Zheng, Xiaoyu Liu, Chao Zhang, Shasha Gao, Zhichao Ji, Shenghong Liu and Wenhe Xie
We successfully designed and prepared hierarchical Ni3S2 nanorod@nanosheet arrays on three-dimensional Ni foam via facile hydrothermal sulfuration. We conducted a series of time- and temperature-dependent experiments to determine the Ostwald ripening process of hierarchical Ni3S2 nanorod@nanosheet arrays. The rationally hierarchical architecture creates an excellent supercapacitor electrode for Ni3S2 nanorod@nanosheet arrays. The areal capacitance of this array reaches 5.5 F cm−2 at 2 mA cm−2, which is much higher than that of Ni3S2 nanosheet arrays (1.5 F cm−2). The corresponding asymmetric supercapacitor exhibits a wide potential window of 1.6 V and energy density up to 1.0 Wh cm−2 when the proposed array is utilized as the positive electrode with activated carbon as the negative electrode. This electrochemical performance enhancement is attributable to the hierarchical structure and synergistic cooperation of macroporous Ni foam and well-aligned Ni3S2 nanorod@nanosheet arrays. Our results represent a promising approach to the preparation of hierarchical nanorod@nanosheet arrays as high-performing electrochemical capacitors.
075605
Li Zhang, Hongcen Zheng, Yonghai Gan, Bingdang Wu, Zhihao Chen, Shuangshuang Wei, Guoyang Zhang, Shujuan Zhang, Bingcai Pan and Chuncheng Chen
Controllable synthesis, proper dispersion, and feasible functionalization are crucial requirements for the application of nanomaterials in many scenarios. Here, we report an all-in-one approach for the synthesis and functionalization of gold nanoparticles (AuNPs) with the simplest β-diketone, acetylacetone (AcAc). With this approach, the particle size of the resultant AuNPs was tunable by simply adjusting the light intensity or AcAc dosage. Moreover, owing to the capping role of AcAc, the resultant AuNPs could be stably dispersed in water for a year without obvious change in morphology and photochemical property. Formation of ligand to metal charge transfer complexes was found to play an important role in the redox conversion of Au with AcAc. Meanwhile, the moderate complexation ability enables the surface AcAc on the AuNPs to undergo ligand exchange reactions (LER). With the aid of Ag+, the AuNPs underwent LER with glutathione and exhibited enhanced photoluminescence (PL) with a maximum of 22-fold increase in PL intensity. The PL response was linear to the concentration of glutathione in the range of 0–500 μM. Such a LER makes the obtained AuNPs being good imaging probes. To the best of our knowledge, this is the first work on illustrating the roles of AcAc as a multifunctional ligand in fabrication of NPs, which sheds new light on the surface modulation in synthesis of nanomaterials.
Materials: properties, characterization or tools
075701
Zhehao Xu, Xiao Su, Sicong Hua, Jiwei Zhai, Sannian Song and Zhitang Song
For high-performance data centers, huge data transfer, reliable data storage and emerging in-memory computing require memory technology with the combination of accelerated access, large capacity and persistence. As for phase-change memory, the Sb-rich compounds Sb7Te3 and GeSb6Te have demonstrated fast switching speed and considerable difference of phase transition temperature. A multilayer structure is built up with the two compounds to reach three non-volatile resistance states. Sequential phase transition in a relationship with the temperature is confirmed to contribute to different resistance states with sufficient thermal stability. With the verification of nanoscale confinement for the integration of Sb7Te3/GeSb6Te multilayer thin film, T-shape PCM cells are fabricated and two SET operations are executed with 40 ns-width pulses, exhibiting good potential for the multi-level PCM candidate.
075702
Muhammad Yasir, Tomáš Šopík, Lenka Lovecká, Dušan Kimmer and Vladimír Sedlařík
This study focuses on the adsorption kinetics of four highly potent sex hormones (estrone (E1), 17β-estradiol (E2), 17α-ethinylestradiol (EE2), and estriol (E3)), present in water reservoirs, which are considered a major cause of fish feminization, low sperm count in males, breast and ovarian cancer in females induced by hormonal imbalance. Herein, electrospun polymeric nanostructures were produced from cellulose acetate, polyamide, polyethersulfone, polyurethanes (918 and elastollan), and polyacrylonitrile (PAN) to simultaneously adsorbing these estrogenic hormones in a single step process and to compare their performance. These nanofibers possessed an average fiber diameter in the range 174–330 nm and their specific surface area ranged between 10.2 and 20.9 m2 g−1. The adsorption–desorption process was investigated in four cycles to determine the effective reusability of the adsorption systems. A one-step high-performance liquid chromatography technique was developed to detect and quantify concurrently each hormone present in the solution. Experimental data were obtained to determine the adsorption kinetics by applying pseudo-first-order, pseudo-second-order and intraparticle diffusion models. Findings showed that E1, E2 and EE2 best fitted pseudo-second-order kinetics, while E3 followed pseudo-first-order kinetics. It was found that polyurethane Elastollan nanofibers had maximum adsorption capacities of 0.801, 0.590, 0.736 and 0.382 mg g−1 for E1, E2, EE2 and E3, respectively. In addition, the results revealed that polyurethane Elastollan nanofibers had the highest percentage efficiency of estrogens removal at ∼58.9% due to its strong hydrogen bonding with estrogenic hormones, while the least removal efficiency for PAN at ∼35.1%. Consecutive adsorption–desorption cycles demonstrated that polyurethane maintained the best efficiency, even after being repeatedly used four times compared to the other polymers. Overall, the findings indicate that all the studied nanostructures have the potential to be effective adsorbents for concurrently eradicating such estrogens from the environment.
075703
Haiyang Fu, Bo Gao, Chenglong Hu, Zhuang Liu, Liang Hu, Jiawen Kan, Zhongbao Feng and Pengfei Xing
Here, we report an improved synthesis strategy for 3D nitrogen-doped graphene to increase the specific capacity of supercapacitors. Ethanol replaces the strong oxidant hydrogen peroxide in the improved Hummers method, and the loose porous structure is conducive to charge transfer. N-doped porous 3D graphene was synthesized from RGO-C prepared by ethanol secondary intercalation modification of functional groups. Ammonia was selected as the dopant; the microstructure and electrochemical performance of samples synthesized at different temperatures were examined. The results demonstrate that the 3D nitrogen-doped graphene (N-RGO-5) had a layered tuple shape with a sheet thickness of 0.612 nm.The specific surface area of the 3D N-RGO-5, which was prepared at 190°C, was 258.371 m2 g−1, which was higher than that (5.877 m2 g−1) of the original graphite. The 3D N-RGO-5 exhibited a specific capacitance of 236 F g−1 and an energy density of 32.78 Wh kg−1 at a current density of 1 A g−1, which is 27% higher than the specific capacitance of RGO. The 3D N-RGO-5 demonstrated an excellent capacity retention rate of 93.6% after 5000 cycles at a current density of 1 A g−1. This study demonstrates that the unique 3D structure and N-doping of N-RGO considerably improved the overall energy storage performance of graphene-based nanomaterials.
075704
Lan Thi Dang, Huy Le Nguyen, Hai Van Pham and Mai Thi Tuyet Nguyen
The accessibility of contaminants detection methods is urgently required for environmental and food safety control. In this report, we developed the Au@Ag core–shell nanorod structures for contaminants sensing by surface-enhanced Raman spectroscopy (SERS). The silver shell thickness and the corresponding plasmon wavelength of Au@Ag core–shell nanorods were tuned by changing the coating time and the silver precursor amount. Moreover, these structures exhibit ultra-sensitive detection ability for Nile blue A dye and Fenobucarb pesticide sensing by SERS. Interestingly, the highest Raman enhancement factor is obtained for the Au@Ag core–shell sample with a minimal silver shell thickness leaded by the optimal enhancement of the electromagnetic field of bimetallic structures. Hence, our report demonstrates that the combination of unique features of two plasmonic metals into core–shell structures promises potential applicability in SERS-based analysis.
075705
Jie Zhang and Yuying Zheng
Graphene (G) is regarded as a tremendous potential corrosion protection material owing to its perfect impermeability. However, the tendency of graphene nanosheets to agglomerate and the corrosion-promotion effect brought by its native high electrical conductivity seriously affect its anti-corrosion application. In this paper, high-energy ball milling was used to prepare graphene with excellent impermeability. Then, insulating poly(m-phenylenediamine) encapsulated graphene (G@PmPD, conductivity of 1.2 × 10−7 S cm−1) was prepared through non-covalent π–π interaction. The resulting amino-rich G@PmPD exhibits stable dispersibility and excellent compatibility in organic solvents and polymer matrix. Embedding 0.5 wt% of G@PmPD into the epoxy matrix, and the composite coating can effectively protect the steel substrate for up to 60 d. This superior corrosion resistance is attributed to the impermeability inherited by G@PmPD and the compactness improved by the cross-linking of G@PmPD and EP. Especially in the damaged state, the composite coating embedded with low conductivity G@PmPD triumphantly eliminated graphene’s corrosion-promotion effect. This study provides promising inspiration for the application of graphene in anti-corrosion field.
075706
Jingze Li, Jiaxin Ma, Liu Hong and Cheng Yang
Achieving an efficient and inexpensive bactericidal effect is a key point for the design of antibacterial agent. Recent advances have proved molybdenum disulfide (MoS2) as a promising platform for antimicrobial applications, while the combination of metal nanoparticle would promote the antibacterial efficiency. Nevertheless, the dispersivity, cheapness and safety of metal nanoparticle loaded on MoS2 raised some concerns. In this paper, we successfully realized a uniform decoration of copper nanoparticles (CuNPs) on surface of MoS2 nanosheets, and the size of CuNPs could be controlled below 5 nm. Under 5 min irradiation of 660 nm visible light, the synthesized CuNPs/MoS2 composite demonstrated superior antibacterial performances (almost 100% bacterial killed) towards both Gram-negative E. coli and Gram-positive S. aureus over the single component (Cu or MoS2), while the bactericidal effect could last for at least 6 h. The synergism of photodynamic generated hydroxyl radical (·OH), oxidative stress without reactive oxygen species production and the release of Cu ions was considered as the mechanism for the antibacterial properties of CuNPs/MoS2. Our findings provided new insights into the development of two-dimensional antibacterial nanomaterials of high cost performance.
075707
A Bafekry, M Faraji, N N Hieu, Yee Sin Ang, S Karbasizadeh, I Abdolhosseini Sarsari and M Ghergherehchi
Motivated by the recent experimental discovery of C6N7 monolayer (Zhao et al 2021 Science Bulletin66, 1764), we show that C6N7 monolayer co-doped with C atom is a Dirac half-metal by employing first-principle density functional theory calculations. The structural, mechanical, electronic and magnetic properties of the co-doped C6N7 are investigated by both the PBE and HSE06 functionals. Pristine C6N7 monolayer is a semiconductor with almost isotropic electronic dispersion around the Γ point. As the doping of the C6N7 takes place, the substitution of an N atom with a C atom transforms the monolayer into a dilute magnetic semiconductor, with the spin-up channel showing a band gap of 2.3 eV, while the spin-down channel exhibits a semimetallic phase with multiple Dirac points. The thermodynamic stability of the system is also checked out via AIMD simulations, showing the monolayer to be free of distortion at 500 K. The emergence of Dirac half-metal in carbon nitride monolayer via atomic doping reveals an exciting material platform for designing novel nanoelectronics and spintronics devices.
075708
Xiaodong He, Jiamei Zhu, Liang Tan, Hongmin Wang and Min Zhou
Altering physicochemical properties of TiO2 based on modifying the cation and anion structure of ionic liquids (ILs) is of great interests for environment. Up to date, the research involving IL-assisted synthesis of TiO2 was focused on imidazolium IL, and much less attention was devoted to IL with other structures. Hence, strategy for preparation of TiO2 in phosphonium IL is presented to control the growth of TiO2 nanocrystals. The as-prepared noble cerium-doped nitrogen-rich phosphonium IL-TiO2 photocatalyst with assisted by tributyl(propyl)phosphonium tetrafluoroborate exhibits a higher specific surface area and smaller crystallite size, which is conducive to the production of more and faster active substance, such as hydroxyl oxygen. When evaluated for photocatalysis of gaseous toluene under visible light irradiation, the sample manifests high degradation rate and efficiency, as well as excellent recycling performance due to the existence of superoxide radical produced by the Ce3+/Ce4+ redox reaction. The introduction of phosphonium IL and Ce greatly enhanced charge separation efficiency and promoted production of active substances. Nitrogen also existed in the form of interstitial nitrogen and substituted nitrogen improves its response to visible light. This work shows promising application of phosphonium IL for highly enhanced TiO2 photocatalytic performance.
075709
Keita Nomoto, Xiang-Yuan Cui, Andrew Breen, Anna V Ceguerra, Ivan Perez-Wurfl, Gavin Conibeer and Simon P Ringer
Thermal annealing temperature and time dictate the microstructure of semiconductor materials such as silicon nanocrystals (Si NCs). Herein, atom probe tomography (APT) and density functional theory (DFT) calculations are used to understand the thermal annealing temperature effects on Si NCs grown in a SiO2 matrix and the distribution behaviour of boron (B) and phosphorus (P) dopant atoms. The APT results demonstrate that raising the annealing temperature promotes growth and increased P concentration of the Si NCs. The data also shows that the thermal annealing does not promote the incorporation of B atoms into Si NCs. Instead, B atoms tend to locate at the interface between the Si NCs and SiO2 matrix. The DFT calculations support the APT data and reveal that oxygen vacancies regulate Si NC growth and dopant distribution. This study provides the detailed microstructure of p-type, intrinsic, and n-type Si NCs with changing annealing temperature and highlights how B and P dopants preferentially locate with respect to the Si NCs embedded in the SiO2 matrix with the aid of oxygen vacancies. These findings will be useful towards future optoelectronic applications.
075710
Jyoti Shakya, Gayathri H N and Arindam Ghosh
MoS2 is an intrinsic piezoelectric material which offers applications such as energy harvesting, sensors, actuators, flexible electronics, energy storage and more. Surprisingly, there are not any suitable, yet economical methods that can produce quality nanosheets of MoS2 in large quantities, hence limiting the possibility of commercialisation of its applications. Here, we demonstrate controlled synthesis of highly crystalline MoS2 nanosheets via liquid phase exfoliation of bulk MoS2, following which we report piezoelectric response from the exfoliated nanosheets. The method of piezo force microscopy was employed to explore the piezo response in mono, bi, tri and multilayers of MoS2 nanosheets. The effective piezoelectric coefficient of MoS2 varies from 9.6 to 25.14 pm V−1. We attribute piezoelectric response in MoS2 nanosheets to the defects formed in it during the synthesis procedure. The presence of defects is confirmed by x-ray photoelectron spectroscopy.