Batteries and Energy Storage
A1393
Soo Yeon Lim, Heejin Kim, R. A. Shakoor, Yousung Jung and Jang Wook Choi
A combined experimental and computational study on Na3V2(PO4)3 has been carried out to investigate its structural, electrochemical, and thermal properties as a sodium battery cathode. The synthesized material by a sol-gel process was well-indexed to the R-3m space group in the framework of a rhombohedral NASICON structure. Galvanostatic measurements indicate that at 3.4 V vs. Na/Na+, 1.4 Na reversibly reacts with each Na3V2(PO4)3, which corresponds to a specific capacity of 84.8 mAh/g. Moreover, this material shows excellent rate capabilities and good cycling performance. Ex-situ XRD analyzes indicate that this material reacts with Na ions based on a reversible two-phase reaction. Thermal analyzes employing TGA/DSC and In-situ XRD at various temperatures show that this material maintains good thermal stability up to 450°C even in the desodiated state. The promising electrochemical and thermal properties suggest that this material with the well-defined NASICON structure is a promising cathode for large-scale sodium rechargeable batteries.
A1398
K. Nakahara, M. Tabuchi, S. Kuroshima, A. Toda, K. Tanimoto and K. Nakano
Iron-containing lithium-rich layered manganese oxides are promising as cathode active materials for fabricating high energy density and low-cost lithium-ion batteries. We synthesized Li1.26Mn0.52Fe0.22O2 (or 0.7Li2MnO3·0.3LiFeO2) by using the co-precipitate-hydrothermal-calcination method. We then tested a graphite/Li1.26Mn0.52Fe0.22O2 cell after a stepwise pre-cycling treatment. The pre-cycling treatment drastically increased the specific capacity of the Li1.26Mn0.52Fe0.22O2 from 167 to 236 mAh g−1 at a current rate of 5 mA g−1. Other cell performances, such as operation voltage, discharge rate capability, and cyclability, also improved with this treatment. An analytical study using gas chromatography revealed that these improvements were derived from the suppression of oxygen release from the oxide lattice. X-ray absorption spectroscopy and X-ray photoelectron spectroscopy analyzes indicated that the main charge compensation mechanism of pre-cycling treatment was not the redox reaction of transition metals, such as Mn3+/Mn4+ and Fe3+/Fe4+, but the redox reaction of O2− accompanying O22− formation in the oxide lattice.
A1405
Hannah M. Dahn, A. J. Smith, J. C. Burns, D. A. Stevens and J. R. Dahn
A user-friendly differential voltage analysis software has been developed and is described here. High-precision reference potential-specific capacity data for Li/negative electrode and Li/positive electrodes, as well as the cycled full cell potential-specific capacity, must be supplied by the user. From these, the differential voltage versus capacity, dV/dQ vs. Q, of a full Li-ion cell is calculated and compared to experiment. The calculated dV/dQ vs. Q curve has four adjustable parameters which are optimized manually with slider bars or automatically by least squares fitting of the calculation to experiment. The parameters are the positive electrode mass, the negative electrode mass, the positive electrode slippage and the negative electrode slippage. Examples of the use of the program are given for graphite/LiCoO2 wound cells cycled for hundreds of cycles. The variation of the four parameters with cycle number give insights into the mechanisms of cell failure equivalent to that which could be obtained with a Li reference electrode inserted within the cell. The software is available free of charge by contacting the authors.
A1410
The following article is Free article
G. Pilatowicz, H. Budde-Meiwes, D. Schulte, J. Kowal, Y. Zhang, X. Du, M. Salman, D. Gonzales, J. Alden and D. U. Sauer
SLI lead-acid batteries are still the most commonly used technology in automotive applications around the world. Despite its relatively low gravimetric and volumetric energy density in comparison with other battery solutions it is still installed in the newest micro-hybrid and conventional cars due to its low cost. To facilitate the design of multi-physical systems as complex as modern automobiles, it is critical to have a precise battery aging model that incorporates various operation conditions. This paper presents a comprehensive battery model which consists of electrical, thermal and aging part that provides crucial information about the current state of SLI battery during lifetime for any conditions like climate, driving style, charging strategy or different battery management approaches. The described model is based on empirical, physico-chemical and equivalent circuit solutions and can be calibrated to simulate any SLI lead-acid battery without design limitations.
A1420
Yongzhu Fu, Yu-Sheng Su and Arumugam Manthiram
Sulfur-polypyrrole composite cathodes with sulfur contents of 77, 64, to 53 wt% have been synthesized by an in-situ deposition of sulfur with polypyrrole pre-synthesized by an oxidation method. The presence of polypyrrole in the form of nanoparticles prohibits the agglomeration of sulfur during the synthesis, resulting in small sulfur particles and well-mixed sulfur-polypyrrole composites. The sulfur-polypyrrole composite cathodes synthesized have been evaluated by cyclic voltammetry, galvanostatic cycling, and electrochemical impedance spectroscopy. The composite cathodes show better electrochemical stability, lower overpotential, and better cyclability compared to the pristine sulfur as the polypyrrole particles facilitate ion and charge transfer within the electrodes. The composites consisting of 64 and 53 wt% of sulfur exhibit higher discharge capacities and better cyclability than sulfur at C/2, 1 C, and 2 C rates, e.g., retaining capacities of >500 mAh/g at 1 C and ∼400 mAh/g at 2 C after 50 cycles. The polypyrrole in the composites improves the electrochemical contact within the electrodes as evidenced by the reduced charge transfer resistance and improved rate capability as well as the porosity of electrodes as revealed by scanning electron microscopy.
A1425
H. Jang, S. Suzuki and M. Miyayama
Self-reassembled MnO2 nanosheets were prepared via nanosheet processes and their electrochemical properties were investigated in 0.1 M Na2SO4 aqueous solution. The MnO2 nanosheets had a plate-like morphology: 2 μm in width and 2 nm in thickness. The electrochemical properties of the MnO2 nanosheet electrodes were largely influenced by the particle size, and a MnO2 nanosheet electrode composed of small-sized particles (fine-NS-MnO2) exhibited a relatively large discharge capacity of 182 F/g-MnO2 compared with the conventional MnO2 electrode capacity of 153 F/g-MnO2 at a current density of 100 mA/g-MnO2. The fine-NS-MnO2 had a large mesoporous volume and large specific surface area, and thus exhibited a good rate capability. In contrast, the MnO2 nanosheet electrode composed of large-sized particles (NS-MnO2) showed poor rate capability due to the large ionic diffusion resistance. Microstructural control by nanosheet processes and reduction of the particle size are important for the design of MnO2 electrodes with superior electrochemical properties.
A1431
Nick S. Norberg and Robert Kostecki
The chemical and structural changes occurring in a LiMnPO4 composite cathode during electrochemical cycling were investigated by ex situ Raman microscopy. An O2-plasma etching procedure was used to remove the thick surface carbon coating and expose LiMnPO4 particles for Raman characterization of LixMnPO4 at different states of charge (SOC). Pyrophosphate species, Li4P2O7, emerged at the exposed part of the LiMnPO4 composite cathode after a full charge and discharge cycle, indicating that the charged LixMnPO4 electrode is not chemically stable in standard LiPF6/carbonate-based electrolytes at room temperature.
A1435
V. Aravindan, Yan L. Cheah, W. Chui Ling and S. Madhavi
Solid-state method is used to synthesize sub-micron size lithium cobalt phosphate, LiCoPO4 particles. Powder X-ray diffraction pattern reveal the formation of pure phase orthorhombic structure with pnma space group. Electrochemical properties of LiCoPO4 are evaluated in half-cell configurations with conventional 1 M LiPF6 ethylene carbonate (EC): diethyl carbonate (DEC) electrolyte solution. Interestingly, increasing charging potential leads to the decrease in re-insertion potential as is confirmed by cyclic voltammetric (CV) measurements. Galvanostatic studies corroborated CV analysis and suggest that higher charge potential delivers maximum discharge capacity, but with severe capacity fade upon cycling. Incorporation of lithium bis(oxalato)borate (LiBOB) in conventional electrolyte solutions certainly enhances the cycleability of LiCoPO4 electrode, for example 3 wt% of LiBOB comprising electrolyte shows capacity retention of 74% of its initial discharge capacity after 25 cycles. The present study elucidates LiBOB addition is one of the unique approaches to alleviate the capacity fade of LiCoPO4 during cycling.
A1440
Ran Elazari, Gregory Salitra, Gregory Gershinsky, Arnd Garsuch, Alexander Panchenko and Doron Aurbach
Si electrodes are the most important high capacity substitutes of Li metal and carbon anodes in high energy density Li ion batteries, including those based on sulfur or air cathodes. In this study we examined amorphous columnar structure silicon film anodes prepared by sputtering in rechargeable Li ion battery prototypes based on TiS2 cathodes. The choice of this cathode material enabled focusing on the examination of pre-lithiated Si films as anode candidates in alkyl carbonate electrolyte solutions. The effectiveness of fluoro-ethylene carbonate (FEC) as a co-solvent in alkyl carbonates/LiPF6 solutions for good performance of silicon anodes was exhibited. Hundreds of cycles were demonstrated in full Li ion cells containing these components. The columnar morphology of these anodes is retained after 1000 cycles. Their surface chemistry, measured by EDS and XPS is discussed. The results of this work encourage further R&D efforts toward the use of amorphous silicon films as anodes in advanced rechargeable Li batteries.
A1446
K. W. Knehr, Ertan Agar, C. R. Dennison, A. R. Kalidindi and E. C. Kumbur
This paper presents a 2-D transient, isothermal model of a vanadium redox flow battery that can predict the species crossover and related capacity loss during operation. The model incorporates the species transport across the membrane due to convection, diffusion, and migration, and accounts for the transfer of water between the half-cells to capture the change in electrolyte volume. The model also accounts for the side reactions and associated changes in species concentration in each half-cell due to vanadium crossover. A set of boundary conditions based on the conservations of flux and current are incorporated at the electrolyte|membrane interfaces to account for the steep gradients in concentration and potential at these interfaces. In addition, the present model further improves upon the accuracy of existing models by incorporating a more complete version of the Nernst equation, which enables accurate prediction of the cell potential without the use of a fitting voltage. A direct comparison of the model predictions with experimental data shows that the model accurately predicts the measured voltage of a single charge/discharge cycle with an average error of 1.83%, and estimates the capacity loss of a 45 cycle experiment with an average error of 4.2%.
A1460
Xin Xia, Ping Ping and J. R. Dahn
The effects of the flame retardant, triphenyl phosphate (TPP), on the electrochemical properties of negative electrode materials for Li-ion batteries were studied. Petroleum coke and graphite were chosen for study. Coke/Li half cells with different concentrations of TPP were studied with a home-made automated storage system. The reactivity of intercalated lithium with TPP-containing electrolyte could be inferred from the potential-time graphs of the coke/Li cells during storage. Graphite/graphite symmetric cells with different concentrations of TPP were constructed and tested. Capacity loss in symmetric graphite/graphite cells is caused by reactions of intercalated lithium with electrolyte. The storage test results showed that coke/Li cells with TPP (10%–40% by volume) have similar rates of Li loss to electrolyte reactions at 30°C compared to control cells and show significantly lower rates at 60°C. Graphite/graphite symmetric cells with TPP (10%–40%) have capacities that decrease with TPP content, but show similar rates of% capacity loss per cycle. The impedance of the symmetric cells increases with TPP content. All the results together suggest that TPP forms a stable SEI but a SEI that impedes the transport of Li.
A1467
P. Ping, Q. S. Wang, J. H. Sun, X. Xia and J. R. Dahn
The effect of triphenyl phosphate (TPP) as a flame retardant additive on the cycling behavior and AC impedance of Li(Ni0.8Co0.15Al0.05)O2/Li(Ni0.8Co0.15Al0.05)O2 (NCA/NCA) and Li(Ni1/3Mn1/3Co1/3)O2/Li(Ni1/3Mn1/3Co1/3)O2 (NMC/NMC) positive symmetric cells was studied. Symmetric cells with two identical electrodes (one was charged first and the other was fresh) were used to determine the impact of the TPP additive on the positive electrode, without the confusing effect of a second, different, electrode. The capacity retention of NCA symmetric cells with TPP was almost as good as cells without TPP when the TPP concentration was no more than 20%. At higher TPP content, impedance increase became problematic. NMC/NMC cells showed significantly worse capacity retention than NCA/NCA cells even without TPP for reasons that are, as yet, unclear. TPP additions above 20% to NMC/NMC cells again lead to dramatic increases in impedance and very poor capacity retention. The addition of 2 wt% vinylene carbonate (VC) decreased the impedance and improved the capacity retention of the NCA/NCA cells with high TPP content. Therefore, electrolytes with up to 40% TPP are compatible with NCA in the presence of 2% VC.
A1474
Jun Ding, Ying Kong, Peng Li and Jinrong Yang
The polyamic acid (PAA), which is the precursor of polyimide (PI), is synthesized by pyromellitic dianhydride (PMDA) and 4, 4′-oxidianiline (ODA). The PAA/PET composite membrane is prepared with poly (ethylene terephthalate) (PET) nonwoven by electrospinning of the solution of PAA. The final PI/PET composite membrane is obtained after a thermal imidization process. The porosity, liquid electrolyte uptake and room temperature ionic conductivity of PI/PET composite membrane decreases a little comparing with PI membrane, but the tensile strength of PI/PET composite membrane increases more than PI ones. The experiments demonstrate that the diameter of the fibers decrease with the increase of the electrospinning voltage. At the same time, the decrease of the fibers diameter leads to the increase of the porosity as well as the liquid electrolyte uptake of the PI/PET composite membranes. As a result, the room temperature ionic conductivity is enhanced from 0.451 to 0.897 mS·cm−1. The PI/PET composite membrane shows only about 2% of thermal shrinkage at 180°C under air atmosphere. The cell with the PI/PET composite membrane shows stable cycling performances and better rate capabilities than the cells with the Celgard one under 10 C-rate.
A1481
Wai Fatt Mak, Grace Wee, Vanchiappan Aravindan, Nutan Gupta, Subodh G. Mhaisalkar and Srinivasan Madhavi
Vanadium pentoxide nanofibers (VNF) and polyaniline nanofibers (PANF) nanofibers are synthesized by electrospinning and rapid chemical polymerization routes, respectively. The electrochemical performances of synthesized nanofibers are evaluated in symmetrical (VNF-VNF, PANF-PANF) and asymmetrical (VNF-PANF) configurations in aqueous KCl (3 M) medium by cyclic voltammetry (CV) and galvanostatic measurements. Both VNF and PANF fibers exhibits pseudocapacitive behavior at the electrode/electrolyte interface. The VNF-PANF asymmetrical device is capable of delivering an energy and power densities of 26.7 Wh kg−1 at 0.22 kW kg−1, respectively which is higher than that of symmetrical configuration of VNF-VNF (5.2 Wh kg−1 at 0.22 kW kg−1). In addition, VNF-PANF asymmetrical supercapacitor retained 73% of specific capacitance after 2000 cycles. These results clearly shows that high energy density supercapacitor can be constructed utilizing transitional metal oxides with conducting polymers as electro-active materials in an asymmetrical configuration in aqueous medium.
A1489
Daniel M. Seo, Oleg Borodin, Sang-Don Han, Paul D. Boyle and Wesley A. Henderson
The electrolyte solution structure for acetonitrile (AN)-lithium salt mixtures has been examined for highly dissociated salts. Phase diagrams are reported for (AN)n-LiN(SO2CF3)2 (LiTFSI) and -LiPF6 electrolytes. Single crystal structures and Raman spectroscopy have been utilized to provide information regarding the solvate species present in the solid-state and liquid phases, as well as the average solvation number variation with salt concentration. Molecular dynamics (MD) simulations of the mixtures have been correlated with the experimental data to provide additional insight into the molecular-level interactions. Quantum chemistry (QC) calculations were performed on (AN)n-Li-(anion)m clusters to validate the ability of the developed many-body polarizable force field (used for the simulations) to accurately describe cluster stability (ionic association). The combination of these techniques provides tremendous insight into the solution structure within these electrolyte mixtures.
A1501
Stephen J. Harris, Ehsan Kabiri Rahani and Vivek B. Shenoy
Most models of battery charging assume a shrinking core model with a Lithium-rich shell and Li-poor core. In this study, we provide direct experimental evidence from in situ optical measurements and that suggests that the lithiation of (spherical) MCMB (meso carbon micro beads) particles do not follow the shriking-core model, even for particles which eventually become uniformly lithiated. We observe “hot spots” which expand until the particles are fully charged. The observations are explained using a microstructural model of MCMB particles that 1) accounts for their polycrystalline nature, 2) anisotropy in diffusion and 3) dependence of the intercalation rate at the surface on the orientation of the graphene planes. We show that our model reproduces the key features of the charging process observed in experiments. Implications of these results to Li-plating are discussed.
A1508
The following article is Free article
E. Prada, D. Di Domenico, Y. Creff, J. Bernard, V. Sauvant-Moynot and F. Huet
Derived from the Pseudo Two-Dimensional mathematical structure, a simplified electrochemical and thermal model of LiFePO4-graphite based Li-ion batteries is developed in this paper. Embedding the porous electrode theory, this model integrates the main design parameters of Li-ion systems and its partial differential equations mathematical structure makes it a promising candidate for battery management system (BMS) applications and comprehensive aging investigations. Based on a modified Single-Particle approach, the model is used to simulate and discuss capacity restitution in galvanostatic charges and discharges at various rates and temperatures. Constant high-rate solicitations similar to fast charge of plug-in electric vehicles or electric vehicles, are experimentally tested and simulated with the present model. Also, thermal issues occurring during these specific operating conditions are quantitatively pointed out. The concept of current-dependent spherical particle radius is used to obtain good agreement with experimental data related to galvanostatic charges and discharges. The capabilities and limits of this preliminary modeling work are discussed in detail and ways to extend the potentialities of this approach to BMS applications are proposed.
A1520
Sumit K. Soni, Brian W. Sheldon, Xingcheng Xiao, Allan F. Bower and Mark W. Verbrugge
Stress due to Li insertion has been considered as a major driving force for the mechanical degradation of high capacity electrode materials in lithium ion batteries. The stress level and distribution in active materials are closely related to lithium ion diffusion and the resulting concentration gradients. In this study, we report in situ stress measurements on amorphous Si thin films to investigate Li diffusion and the mechanical response during electrochemical cycling. This configuration was used as a model system to understand how Li diffusion can impact the cyclic performance. The effect of diffusion limitations were studied by systematically varying the C-rate from C/20 to 5C. Experimentally obtained results were then compared to a finite strain model of stress, diffusion, plastic flow, and electrochemical reactions in a lithium half-cell. The calculated results indicate that slow Li diffusion in silicon leads to stress gradients and that high C rates can lead to local stresses and film cracking that are consistent with experimental observations.
A1528
Jonathan P. Neidhardt, David N. Fronczek, Thomas Jahnke, Timo Danner, Birger Horstmann and Wolfgang G. Bessler
Multi-phase management is crucial for performance and durability of electrochemical cells such as batteries and fuel cells. In this paper we present a generic framework for describing the two-dimensional spatiotemporal evolution of gaseous, liquid and solid phases, as well as their interdependence with interfacial (electro-)chemistry and microstructure in a continuum description. The modeling domain consists of up to seven layers (current collectors, channels, electrodes, separator/membrane), each of which can consist of an arbitrary number of bulk phases (gas, liquid, solid) and connecting interfaces (two-phase or multi-phase boundaries). Bulk and interfacial chemistry is described using global or elementary kinetic reactions. Multi-phase management is coupled to chemistry and to mass and charge transport within bulk phases. The functionality and flexibility of this framework is demonstrated using four application areas in the context of post-lithium-ion batteries and fuel cells, that is, lithium-sulfur (Li-S) cells, lithium-oxygen (Li-O) cells, solid oxide fuel cells (SOFC) and polymer electrolyte membrane fuel cells (PEFC). The results are compared to models available in literature and properties of the generic framework are discussed.
A1543
Guoying Chen, Bin Hai, Alpesh K. Shukla and Hugues Duncan
Structure, morphology, and performance of Li1+x(Ni0.33Mn0.33Co0.33)1-xO2 cathode materials with stoichiometric (x = 0) and excess Li (x = 0.14) were compared on micron-sized, well-formed single crystals. The additional Li in the fresh overlithiated oxide facilitated the formation of a superstructure with
ahex ×
ahex × chex unit cells, decreased the cell volume change, and improved the initial O3 phase stability upon lithium extraction. Slower kinetics were observed at low Li content where oxide activation dominated, a process that induced significant structure rearrangements and particle damages. For the first time, morphological evaluation during delithiation was well captured on the micron-sized single crystals. An irreversible activation plateau at 4.4 V was only observed during the first charge of the overlithiated crystals. The oxide's higher discharge capacity and better cycling stability between 2.5 and 4.8 V were attributed to its enhanced O3 phase stability upon deep Li extraction.
A1551
Shin-Kook Kong, Bok-Ki Kim and Woo-Young Yoon
The prevention of Li dendrite growth in Li-metal secondary cells is investigated using high-Li-content electrodes. Li powder is formed using droplet emulsions, and the powder is then used to fabricate porous Li-powder electrodes that are tested against Li-foil electrodes. Scanning electron microscopy results show that dendrites form in a Li-foil cell when the cell is charged and discharged to 25% of the theoretical Li capacity (965 mAhg−1) at 1/3 C-rate (5mAcm−2). This dendrite formation causes cell failure after 10 cycles. No dendrites are observed in the Li-powder cell tested for 250 cycles. Li-powder anodes can be used directly in high-capacity cells such as Li-air or Li-S cells.
A1554
Philippe G. Perret, Patrick R. L. Malenfant, Christina Bock and Barry MacDougall
The electro-deposition and dissolution of MnO2 is studied for its potential utilization in hybrid supercapacitors. A commercially available graphene powder is used as high surface area substrate and capacitive type electrode. An aqueous electrolyte composed of 0.5 M H2SO4 + 0.5 M MnSO4 is used. The deposition-dissolution reaction of MnO2 is shown to provide the bulk of the charge storable in the battery type electrode. Furthermore, the potential window of stability of this electrode reaction is compatible with the aqueous electrolyte. Two complete systems were assembled and tested for their charge/discharge behavior. It is shown that energy and power densities of 25 Wh kg−1 and 980 W kg−1, respectively, can be achieved for at least 5000 cycles. Limitations of the system in terms of cycle numbers and electrolyte volume are discussed in more detail. The electrolyte volume to electrode mass ratio is shown to be a critical factor in determining the charge/discharge cycle number of the device. This is believed to be due to the fact that the efficiency of the MnO2 electro-dissolution/deposition process is less than 100%. This, in turn, could result in gradual pH changes and a lower Mn2+ concentration in the electrolyte during continues charging and discharging. This eventually results in lowering the energy and power density of the system. However, it is shown that an energy density of 25 Wh kg−1 is achievable, thus being comparable with similar hybrid systems.
A1562
Thomas E. Conry, Apurva Mehta, Jordi Cabana and Marca M. Doeff
The structural and electronic effects of Al-substitution in LiNi0.45Mn0.45Co0.1−yAlyO2 electrode materials were explored on a local scale using X-ray absorption spectroscopy (XAS). Homogeneous substitution of Al is observed between 0 ≤ y ≤ 0.10, additionally causing relaxation within the strained edge-sharing metal octahedra composing the transition metal plane. Ex situ measurements on electrochemically charged electrodes confirm that the main charge compensation mechanism occurs via oxidation of Ni, though a contribution centered at the Co-sites was detected in the early stages of charging. Al-substitution, meanwhile, appears to have a negligible local order effect. Analysis of electrochemically cycled materials suggests that there is a beneficial structural consequence of the Al-substitution, which limits the disorder within the local structure of the substituted samples compared to the fresh layered oxides.
Chemical and Biological Sensors
B789
Simona Florentina Pop, Raluca-Ioana Stefan-van Staden, Jacobus Frederick van Staden, Hassan Y. Aboul-Enein, Rodica-Mariana Ion and Zeynep Aydoğmuş
Eight microelectrodes based on the complexes of zinc with porphyrins or phthalocyanines immobilized in carbon or diamond paste matrices were proposed for the assay of oseltamivir phosphate in its pharmaceutical formulation using differential pulse voltammetry (DPV). The limits of detection were between 3.64 × 10−14 and 8.17 × 10−9 mol/L. Oseltamivir phosphate was recovered reliable from pharmaceutical and biological samples in percentages higher than 91.00%. The surface of the microelectrodes can easily be renewed by simple polishing on aluminum foil, obtaining a fresh surface ready for use.
Corrosion Science and Technology
C383
Hai-Sheng Lu, Xu Zeng, Jing-Xuan Wang, Fei Chen and Xin-Ping Qu
Cobalt has caused much interest as an adhesion layer for copper metallization in the next generation interconnect technology. This work investigates the effects of glycine and BTA on corrosion and polishing properties of Co in the acid slurry. The potentiodynamic polarization measurement results show that glycine can increase the corrosion rate of Co. In the solution containing H2O2, adding glycine can make the Co surface smoother. In the slurry without H2O2, BTA shows good inhibition effect on Co corrosion. BTA can adsorb on the Co surface through physisorption and chemisorption, and obeys Langmuir absorption isotherm. In the acid slurry with H2O2, BTA will react with Co2+ ions and form insoluble networked nanoparticles ([Co(II)(BTA)2·H2O]n) on the Co surface, and induce reduction of the removal rate and static etch rate of Co.
C388
Wenying Zhang, Bin Hua, Nanqi Duan, Jian Pu, Bo Chi and Jian Li
A conductive spinel CuFe2O4 is used to protect the metallic interconnect of solid oxide fuel cells (SOFCs) from oxidation and prevent the cathode from chromium poisoning. It is coated by the sol-gel method on a typical metallic interconnect material of Fe-16Cr alloy and evaluated by oxidation at 800°C for 200 h in air (the cathode atmosphere) under an applied current of 0.5 A cm−2. The results show that the coating is promising in providing oxidation resistance, and the oxide scale formed on both the positive and negative sides of the substrate are similar, which consists of a thin inner layer of Cr2O3, a middle layer of Cu-doped MnCr2O4 and a top layer of Fe2O3 with an overall thickness around 2 μm and grows less than 0.5 μm during the 200 h oxidation. The extrapolated area specific resistance (ASR) of the oxide scale at 800°C is approximately one seventh that formed on the uncoated Fe-16Cr alloy, suggesting that the outward migration of cations from the alloy substrate to the oxide scale is driven by the gradient of chemical potential rather than that of electrical potential in this particular situation due to the relatively high scale conductivity.
C393
G. A. Zhang, M. X. Lu, Y. B. Qiu, X. P. Guo and Z. Y. Chen
The electrochemical behavior of carbon steel in high pressure CO2-containing formation water was studied by in situ electrochemical measurements in an autoclave. According to a thermodynamics model, the equilibrium concentrations of various species and the equilibrium potentials of various electrode reactions were calculated to determine the possible electrode reactions. Electrochemical measurements show that in the initial stage, the impedance spectra exhibit three time constants, i.e., capacitive semicircle at high frequency, inductive semicircle at intermediate frequency and capacitive semicircle at low frequency. As corrosion proceeds, the inductive semicircle shrinks and the capacitive semicircle at low frequency enlarges. Impedance spectra exhibit double capacitive semicircles later. In the last stage, Warburg impedance representing diffusion effect appears at low frequency. The electrochemical mechanism is closely related to the formation process of corrosion scales.
C403
Yongsheng Hao, Fuchun Liu and Enhou Han
Epoxy coatings containing different volume fractions of a ferrite inhibition pigment, Ferrinov-100, have been successfully prepared and their inhibitive properties have been studied by electrochemical impedance spectroscopy (EIS) and immersion tests. The results showed that Ferrinov-100 can improve the protective ability of the epoxy coating, but only if its volume fraction is 10%. Scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and X-ray diffraction (XRD) spectra results indicate that Ferrionv-100 can form a double inhibitive layer on the steel surface.
C411
Mustafa Urgen, Özgül Keleş, B. Deniz Polat and Fatma Bayata
This work explores anodic polarization process to generate a surface pattern composed of conical features on an aluminum surface in hot acid mixtures composed of sulfuric and phosphoric acids. It is shown that the composition of the electrolyte with respect to its phosphoric acid and water content and the surface roughness of the aluminum substrate are the critical parameters for the formation of the patterns. The best surface pattern was generated in a hot acidic mixture (60°C) containing 150 mL sulfuric and 350 mL phosphoric acids on a ground aluminum surface. For the formation of conical structures, a mechanism based on the competitive etching action of sulfuric acid and the formation of phosphate precipitates is proposed. Additionally, the possibility of porous anodization of these surfaces in an oxalic acid based electrolyte has been also demonstrated.
C416
Heon-Young Ha and Hyuk-Sang Kwon
For pure Fe, solution pH effects on a pitting potential and passive film properties were examined in a borate-phosphate buffer solution using a polarization test, Mott-Schottky analysis, and a galvanostatic test. Combining the results, the relationship between the surface charge and pitting potential was presented. Passive film analyzes revealed that the most protective passive film with the lowest defect density and highest thickness was formed on Fe in the buffer solution at pH 8.5-9. From the dependency of the film thickness on the solution pH, it was concluded that the surface charge of the film was changed by the pH from positive to negative at pH 8.5-9, thus, the film dissolved via an H+-assisted reaction below pH 8.5, and via H2O-assisted reaction above pH 9. Due to the change in the film dissolution reaction, the ion accumulation in the interfacial diffuse layer was altered from cation-selectivity at pH levels lower than 8.5 to anion-selectivity at pH levels higher than pH 9. It was confirmed that the Cl− attack on the passivated Fe surface was significantly limited in the buffer solution with pH levels higher than 9 due to the formation of the anion-selective diffuse layer.
C422
Eleonora Bettini, Christofer Leygraf, Changjian Lin, Ping Liu and Jinshan Pan
In this study, preferential sites for metal dissolution during anodic polarization were investigated for a biomedical CoCrMo alloy. As-cast and heat treated materials were compared through a combination of complementary techniques. Scanning Kelvin probe force microscopy mapping suggested the matrix areas adjacent to the carbides to be preferential sites for metal dissolution. By means of in situ electrochemical-optical microscopy it was observed that localized dissolution initiated from the matrix areas adjacent to carbides and grain boundaries in both materials at high anodic potential. By using scanning electron microscopy and transmission electron microscopy/energy dispersive spectroscopy analysis, submicron-sized carbides were found along the grain boundaries, and significant Cr depletion was detected across the grain boundaries for both materials, providing an explanation for the initiation of metal dissolution. A slightly higher metal dissolution was observed for the as-cast sample at high anodic potential, probably due to a more heterogeneous microstructure.
C428
S. J. Garcia-Vergara, P. Skeldon, G. E. Thompson, G. Williams and H. N. McMurray
A scanning Kelvin probe technique is used to study the influences of the enriched alloy layers on the corrosion behavior of surface-treated, sputtering-deposited Al-0.7at.%Cu and Al-1.0at.%Au alloys. The alloys were etched in sodium hydroxide solution to produce the enriched layers of copper and gold respectively at the alloy/oxide interface. Volta potential measurements were performed for specimens in both the as-deposited and the alkaline-etched conditions in a humid air atmosphere. The results show the same increasing tendency with increase of enrichment observed in conventional measurements of the corrosion potential in bulk aqueous media. The findings support the key role played by enriched alloy layers in the electrochemical behavior of aluminum alloys.
Electrochemical/Electroless Deposition
D501
Nuno M. Pereira, Paula M. V. Fernandes, Carlos M. Pereira and A. Fernando Silva
The use of deep eutectic solvents (DES) for metal electrodeposition has become an area of interest in the recent years however the use of additives on the electrodeposition from deep eutectic solvents is still an unexplored area. In this study we describe the influence of the tartrate ion on the deposition mechanism of zinc and on the resultant morphology of the deposits. Electrochemical techniques were used to characterize the deposition process and scanning electron microscopy was used to study the deposit morphology. It is shown that the presence of potassium hydrogen tartrate in ethaline does not alter the generic voltammetric profile of zinc in solution but in contrast the presence of tartaric acid cause major modifications. From the analysis of the chronoamperometric transients a 3D progressive nucleation mechanism is proposed for the deposition of zinc in absence and in the presence of potassium hydrogen tartrate. In the presence of tartaric acid a 2D progressive nucleation mechanism is proposed for the initial part of the deposition then changing to a 3D progressive mechanism. The SEM images reveal that both additives change the morphological characteristics of the deposits. However the use of tartaric acid introduces a more dramatic change.
D507
Chih-Hao Chen, Hao-Lin Yang, Ho-Rei Chen and Chien-Liang Lee
Electrochemical surface areas (ESAs) were used to estimate the specific activities of different-sized Ag nanoplates (NPLs), which were used as novel catalysts for electroless copper deposition (ECD). Based on the consideration of ESAs and deposition kinetics measured using an electrochemical quartz crystal microbalance, the mean specific activities of NPLs with sizes of 74 nm, 117 nm, and 162 nm were determined to be 0.107, 0.250, and 1.017 mg·cm−2, respectively. The largest NPLs showed the highest activity. Simultaneously, in the Tafel plot normalized to the ESA, the specific current density corresponding to 74 nm < 117 nm < 162 nm NPLs for formaldehyde oxidation in the high overpotential region was determined. This anodic reaction activated with various NPLs could thus be the rate-determining step in ECD. Additionally, an untypical open circuit potential curve containing two mixed potentials for two period depositions—Cu deposition on Ag NPLs and Cu on the deposited Cu layer—was observed. In the intended application, conductive Cu patterns on a flexible polyimide film using Ag NPL ink of 2.5 wt% solid content were successfully fabricated by inkjet printing combined with catalyzed ECD.
D512
Yung-Huang Chang, Hsiao-Wei Lin and Chih Chen
The growth rate and the growth mechanism are investigated by examining the results of scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) on TiO2 nanorods fabricated in the second anodization process through the nanopores of anodic aluminum oxide. Due to the strong electric field of 1.86 GV/m to 1.33 GV/m, the average ultra-fast growth rate of 250 nm/s is observed, and the abrupt increase of height reaches to 85.2% of its destined height in the early growth stage of 0.6 s. Then the growth rate decreases when the electric field decays with the increase of height, and it is interrupted by the dielectric breakdown under an electric field of 0.65 GV/m. According to the XPS analyzes, the TiO2 species on the outer shell of nanorods are observed, and the sub-oxides, Ti2O3 and TiO, are exhibited after Ar+ ions sputtering. It is proposed that the bottom growth mechanism is identified by the analyzes upon SEM and XPS results.
D518
Yueh-Yuan Fang, Yi-Cheng Hsieh and Chii-Wann Lin
This work demonstrates a method of electroplating nanostructured Pt, Ir, and Pt-Ir at room temperature. All the obtained samples have been characterized by SEM and XPS. By controlling the volume ratio of Pt to Ir electrolytes, Pt(100%)-Ir(0%), Pt(91.2%)-Ir(8.8%), Pt(81.3%)-Ir(18.7%), and Pt(12.4%)-Ir(87.6%) were formed on the surfaces. Besides, the nanostructure was formed with the help of vigorously hydrogen bubble generation. The results indicate that co-electrodeposition of nanostructured Pt-Ir films at room temperature can be achieved by manipulating the concentration of Ir electrolyte and the concentration of HCl.
D521
R. G. Milazzo, G. D’Arrigo, C. Spinella, M. G. Grimaldi and E. Rimini
A systematic study of silver-catalyzed etching in (100) and (111) n-type Silicon substrates is carried out by varying the amount and the morphology of electroless deposited silver clusters. Deposition rate is very fast during the first few seconds and then it levels at a lower value of one order magnitude for both oriented wafers. For small and well separated clusters the Si nanowires formed by the etching are aligned along the (100) axes, while for large and interconnected they are oriented along the normal to the surface. For the (100) Si substrate partially covered with small silver clusters the etching proceeds both in vertical and horizontal [100] directions. For larger coverage (70%) the Ag nanoparticles sink all together along the vertical direction. For the (111) Si substrate, when the Ag nanoparticles are isolated they sink in all the equivalent [100] directions with an irregular path; when the Ag nanoparticles begin to coalesce uniform domains of Si nanowires aligned along [100] directions are formed. When the silver clusters are well interconnected (70% of coverage), the etching is vertical. Silver coverage is then another experimental parameter to induce a preferred orientation of the etched Si nanowires.
D526
Q. Huang, B. C. Baker-O’Neal, C. Parks, M. Hopstaken, A. Fluegel, C. Emnet, M. Arnold and D. Mayer
The electrochemical behavior of levelers was studied and compared for two commercial Cu plating chemistries in an effort to correlate the electrochemical behaviors with their impacts on bottom-up filling, impurity incorporation, and grain structures. While a strong complexing between leveler and accelerator resulted in a leveler-sensitive bottom-up filling rate and low impurity level in the deposit, a traditional non-interacting leveler showed little impact on the filling performance and yielded a high impurity incorporation. An oscillatory behavior was reported for the strongly-interacting leveler chemistry during galvanostatic plating, this oscillation manifested itself in both the potential and impurity incorporation. High impurity incorporation is known to inhibit the Cu grain growth; a laminated structure with alternating layers of big and fine Cu grains was obtained by annealing the Cu films plated with the oscillatory behavior.
D532
Rajarshi Saha, Hyo-Chol Koo, Ping Nicole An and Paul A. Kohl
The thermal cycling and effect of misalignment of all-copper, chip-to-substrate bonding was evaluated. Electroplated copper pillars on the chip and board were joined using an optimized electroless deposition process after alignment. The width of the copper lines were 50, 25 and 15 μm The joints were robust and void-free. The mechanical strength and electrical continuity of the bonded copper pillars were assessed before and after thermal cycling. The mechanical strength of these joints was substantially higher than typical solder fracture strength. Finite element medeling was used to analyze the effect of (i) misalignment and (ii) underfill on the mechanics of the assembled parts.
D538
Myung Jun Kim, Taeho Lim, Kyung Ju Park, Sung Ki Cho, Soo-Kil Kim and Jae Jeong Kim
One of the main concerns in fabricating Cu interconnections is a significant increase in resistivity. Thus, pulse-reverse electrodeposition was implemented in an attempt to improve the properties of Cu films. The influences of the anodic step in pulse-reverse electrodeposition were intensively investigated by varying the anodic potential and time (the amount of anodic charge). It was confirmed that the anodic step affected the grain size as well as surface roughness and the change rates of these properties were determined by the anodic potential. The conflicting effects between grain size and surface roughness resulted in the lowest resistivity at an optimum amount of anodic charge. The contributions of the grain size and surface roughness were taken into account to explain the resistivity behavior depending on the anodic charge. A theoretical approach was applied to complement the qualitative findings and it was well-matched with the experimental results.
D544
Myung Jun Kim, Taeho Lim, Kyung Ju Park, Oh Joong Kwon, Soo-Kil Kim and Jae Jeong Kim
Pulse-reverse electrodeposition is capable of improving the superfilling ability and other properties of Cu in device interconnections. In this research, the influences of pulse-reverse electrodeposition on the properties of Cu thin film were investigated in the presence of organic additives used for Cu superfilling. The anodic step of pulse-reverse electrodeposition gave rise to changes in crystallinity, resistivity, grain size, and surface roughness. Minimum resistivity at the optimum dissolution ratio was observed, revealing a 14% reduction of the resistivity as compared to pulse electrodeposition samples. This was ascribed to the minimization of surface roughness produced by the selective dissolution of SPS-covered Cu as opposed to PEG-Cl−-covered Cu. It was confirmed that the selectivity of the anodic step came from the adsorbates and the anodic potential, resulting in changes in the film properties.
D549
Hana Kim, M. C. Murphy and E. J. Podlaha
Electrodeposition of Super Invar thin films and micro-posts are presented. Different pulse plating parameters were applied and the deposit composition distribution along the length of the microstructures was examined. Pulse plating (−60 mA cm−2, 2 s/ 0 mA cm−2, 27 s) was critical in achieving a uniform composition distribution in 100 micron deep features. Using a pulse scheme with a low, non-zero current step introduced more cracks into the deposit, which were characterized by SEM. The coefficient of thermal expansion (CTE) of the micro-post arrays was also determined and exhibited negative values in the axial direction, i.e., the micro-posts shrink with temperature. Structures with micron size cracks exhibited large, negative CTE values during the first heat cycle of the CTE test and then exhibited less dimensional change with a subsequent heat cycle.
D555
Gert Göransson, Matthias Peter, Jiri Franc, Valery Petrykin, Elisabet Ahlberg and Petr Krtil
Ni rich NiZn alloys were prepared on Pt substrates by galvanostatic pulse plating from baths of variable Ni:Zn ratio. The pulse plated NiZn alloys are crystallographically amorphous and their overall chemical composition shows relatively weak dependence on the pulse plating conditions. The local structure of the NiZn alloys determined from EXAFS spectra conforms to a model assuming coexistence of cubic and hexagonal-like arrangements. In the case of alloys plated from baths of low Zn content the cubic environment is zinc free and in the case of alloys plated from bath of high Zn content the Zn enters both cubic and hexagonal arrangement. The fraction of each of the coexisting local structures reflects the pulse plating conditions. The Ni rich NiZn alloys are active in the hydrogen evolution reaction showing electrocatalytic activity superior to that of bulk nickel. The electrocatalytic activity of the alloy samples in hydrogen evolution increases with increasing fraction of hexagonal local structure. This behavior is attributed to the residual strain mainly in the hexagonal-like environment.
Electrochemical Engineering
E149
A. Z. Turan, İ. Y. Elbeyli and İ. E. Kalafatoğlu
In the present work, membrane electrolysis of nearly saturated borax solution prepared from borax pentahydrate (Na2B4O7.5H2O) was studied. Mono layer cation-exchange membrane (Nafion 551) was used as a separator in a two-compartment electrolysis cell for the production of sodium hydroxide and boric acid. The anolyte concentration was adjusted in order to obtain a Na2O/B2O3 mol ratio of 0.1 by dissolving boric acid and borax pentahydrate together. Experiments were performed in continuous operation mode by feeding nearly saturated borax solution. The effects of different catholyte concentrations (10, 20, and 30% NaOH) on the current efficiency and the specific energy consumption were calculated and the quality of boric acid products was determined.
E154
Syamal Maiti, Dipayan Das and Kushal Sen
This work deals with the electrochemical polymerization of pyrrole. The electrochemical polymerization process is evaluated in terms of polymer yield and conversion with respect to monomer and dopant concentrations, applied voltage, and polymerization temperature. An expression for predicting the system current as a function of the aforesaid process parameters has been developed. The system current and normalized system current have been found to be the determining factors for controlling the yield and conversion, respectively.
Fuel Cells, Electrolyzers, and Energy Conversion
F501
S. T. Bliznakov, M. B. Vukmirovic, L. Yang, E. A. Sutter and R. R. Adzic
In this article we describe further improvement of high-performance Pt monolayer-shell on carbon-supported Pd nanowires/nanorods-core electrocatalysts for the oxygen reduction reaction. This improvement is facilitated by electrochemical deposition of Pd nanostructured cores on functionalized carbon surfaces. We describe in some detail this first electrochemical deposition of Pd nanowires, including the effect of deposition parameters on the deposits morphology, and propose the mechanism of the Pd nanostructures growth. The one-dimensional growth of Pd is ascribed to the hydrogen-underpotential-deposition-mediated layer-by-layer deposition of Pd. The surface structure of deposited nanowires is composed predominantly of the {111}-oriented facets that facilitate the enhanced oxygen reduction and high stability of these electrocatalysts. They have significantly higher Pt mass-, and area- specific activities and performance stability under potential cycling conditions than commercial Pt/C electrocatalysts, which indicates their great potential for resolving the remaining obstacles to commercializing PEMFCs.
F507
Romain Dugas, Ana C. Tavares and Daniel Guay
Composite membranes were prepared by mixing RuO2·xH2O (with x = 0.0, 0.6 and 2.2) and polypropylene, an inert polymer matrix. The impedance of these homogeneous composite membranes was measured in 0.5 M H2SO4 over a frequency range from 1 mHz to 1 kHz. A three-dimensional model was devised to fit the experimental impedance spectra. It consists of a percolating network of homogeneous transmission lines to represent RuO2·xH2O, and resistors to account for the polypropylene inert matrix. The model has four parameters that can be varied: P, C, Re and Ri, which are the volume fraction, capacitance, and electronic and ionic resistance of the active material, respectively. The model allows establishing a link between the macroscopic (and measurable) properties of a composite membrane and the microscopic properties of the constitutive materials. Accordingly, an upper limit to the DC proton conductivity of hydrous ruthenium dioxide was established: σi = 64, 27 and 10 mS.cm−1 for x = 0.0, 0.6 and 2.2, respectively.
F514
Eric J. Dufek, Tedd E. Lister, Simon G. Stone and Michael E. McIlwain
A pressurized electrochemical system equipped for continuous reduction of CO2 is presented. At elevated pressures, using a Ag-based cathode, the quantity of CO which can be generated is 5 times that observed at ambient pressure with faradaic efficiencies as high as 92% observed at 350 mA cm−2. For operation at 225 mA cm−2 and 60°C the cell voltage at 18.5 atm was 0.4 V below that observed at ambient pressure. Increasing the temperature further to 90°C led to a cell voltage below 3 V (18.5 atm and 90°C), which equates to an electrical efficiency of 50%.
F518
D. A. Caulk, A. M. Brenner and S. M. Clapham
This paper describes a new steady permeation method for measuring water transport properties of fuel cell membranes. It is distinguished from most previous experiments of this type by employing a separate procedure for quantifying the extraneous sources of water transport resistance in the measurement cell that do not originate in the membrane (the so-called device resistance). This result is then used to determine the membrane water permeability in cells built with Nafion membranes in three thicknesses (25, 50, and 125 microns) operating at three different temperatures (70, 90 and 110°C) over a range of relative humidities from 30–90%. The permeability data lie along three parallel straight lines (one for each temperature) on semi-log plots vs. average membrane relative humidity. There is no discernible dependence of permeability on membrane thickness, suggesting that any localized transport resistance that may exist at the membrane surface was too small to be detected by this method. The permeability data can be fit to a simple 3-constant empirical expression for the membrane permeability as a function of temperature and relative humidity. The largest difference between the present and previous measurements occurs at higher relative humidities, where the device resistance is large compared with the membrane resistance.
F530
Ahmet Kusoglu, Anthony Kwong, Kyle T. Clark, Haluna P. Gunterman and Adam Z. Weber
Catalyst layers (CLs) in proton-exchange-membrane fuel cells (PEMFCs) facilitate electrochemical reactions and therefore play a critical role in cell performance. Absorption and desorption of water into both the CL ionomer and the CL pore structure are integral aspects of PEMFC water management and performance. In this work, the water uptake from both the vapor and liquid phases is examined experimentally. Specifically, the dynamic water-uptake behavior of the CL ionomer is investigated as a function of relative humidity, temperature, Pt-loading and pretreatment. The water content of the ionomer in the CL, even after pretreatment, is found to be significantly lower than that for the bulk ionomer membrane, yet with similar sorption time constants. Thus, there is probably substantially slower transport into the ionomer which is likely due to its interfacial character. From the liquid phase, measured capillary pressure – saturation relationships show that the CL has an appreciably hydrophilicity that is strongly dependent on the existence of cracks. These findings are critical to the understanding and optimization of water management and transport phenomena within PEMFCs.
F536
Tomas Rosén, Jens Eller, Jinfen Kang, Nikolaos I. Prasianakis, John Mantzaras and Felix N. Büchi
Operating Polymer Electrolyte Fuel Cells (PEFC) under high current density conditions, causes significant losses related to liquid water saturation in the gas diffusion layer (GDL). The blockage of pores inside the material has a strong influence on its effective gas transport properties. Here we report on the combination of in-situ X-ray tomographic microscopy (XTM) of PEFC and the numerical determination of gas transport properties using Lattice Boltzmann and finite difference methods. The GDL domains (Toray TGP-H-060) of two identical cells, each with 11 mm2 active area, were analyzed in sections of about 0.3 to 0.8 mm2 size. Saturation levels between 0.1 and 0.4 were found, with higher saturation under the ribs. The saturated and the non-saturated states of the GDL samples were compared in order to quantify the dependence of gas phase permeability and effective relative diffusivity on liquid water saturation. Both these relative measures were found to follow power relationships of (1 − s)λ, where the exponent λ was approximately 3 for all cases except for the in-plane diffusivity where it was closer to 2.
F545
Richard S. Fu, Ugur Pasaogullari, Takeshi Shiomi, Yuichiro Tabuchi, Daniel S. Hussey and David L. Jacobson
We re-investigate our previously studied water transport phenomena under nonisothermal conditions by measuring the through-plane liquid water distribution across PEFC components with the state-of-the-art high-resolution neutron radiography. A corrective postprocessing procedure to eliminate artifacts arising from polymer electrolyte membrane (PEM) swelling in water thickness measurement is introduced for the first time. Presence of a water content gradient in the polymer electrolyte membrane was observed under large temperature gradient and high humidity conditions. Water distribution in gas diffusion layers (GDLs) was measured by replacing the PEM with a film of PTFE. The experiment yielded a pronounced liquid water peak at the PTFE interface.
F554
Zhongyi Liu, Huolin Xin, Zhiqiang Yu, Ye Zhu, Junliang Zhang, Julia A. Mundy, David A. Muller and Frederick T. Wagner
Advanced electron microscopy techniques, i.e., high angle annular dark field (HAADF) imaging, elemental mapping based on electron energy loss spectroscopy (EELS), and three-dimensional (3D) reconstructions from electron tomography, have been used to characterize the complex spongy core-shell structures observed in a high-performing fuel cell catalyst, a dealloyed PtCo3 catalyst supported on high surface carbon (or D-PtCo3/HSC). HAADF imaging showed that multiple dark-contrast patches were randomly decorated on the D-PtCo3 nanoparticles, a type of image that had previously been reported for other catalysts and had been referred to as a spongy structure. In this work, EELS-based elemental mapping revealed that not all of the dark-contrast patches were simple holes (as had been reported for other catalysts). Rather, in this material, while some of the dark-contrast patches corresponded to voids or divots, others were Co-rich cores. The probability of a dark-contrast patch in an HAADF being a Co-rich core was statistically determined to be 58% ± 15%. 3D tomography further confirmed the existence of voids and divots in the multi-core/shell-structured D-PtCo3 nanoparticles. Possible formation mechanisms of the spongy multi-core/shell structure are discussed.
F560
Christian Walter, Kurt Kummer, Denis Vyalikh, Volker Brüser, Antje Quade and Klaus-Dieter Weltmann
The chemical structure of cobalt–polypyrrole – produced by a dual plasma process – is analyzed by means of X-ray photoelectron spectroscopy (XPS), near edge X-ray absorption spectroscopy (NEXAFS), X-ray diffraction (XRD), energy-dispersive X-Ray spectroscopy (EDX) and extended X-ray absorption spectroscopy (EXAFS). It is shown that only nanoparticles of a size of 3 nm with the low temperature crystal structure of cobalt are present within the compound. Besides that, cobalt–nitrogen and carbon–oxygen structures are observed. Furthermore, more and more cobalt–nitrogen structures are produced when increasing the magnetron power. Linking the information on the chemical structure to the results about the catalytic activity of the films – which are presented in part I of this contribution – it is concluded that the cobalt–nitrogen structures are the probable catalytically active sites. The cobalt–nitrogen bond length is calculated as 2.09 Å and the carbon–nitrogen bond length as 1.38 Å.
F570
Yunlong Wang, Yao Wang and Changrong Xia
Ceria and doped ceria materials are often used as the oxide components for solid oxide fuel cell (SOFC) anodes to enhance their catalytic activity, especially those using Cu as the electronic conductors. In this work, the surface process of doped ceria reduction, i.e. the chemical surface exchange process in reduced atmospheres, is studied using electrical conductivity relaxation (ECR) technique to characterize their catalytic activity for fuel oxidation. The oxygen surface exchange coefficient of Gd0.1Ce0.9O2-δ is comparable to that obtained by thermogravimetric measurement, demonstrating the feasibility of ECR method in determining the oxygen transport in doped ceria under reducing conditions. The relaxation process is limited by the surface exchange step and almost independent on the bulk oxygen ion diffusion kinetics. Among various materials of R0.2Ce0.8O2-δ (R = Y, Gd, Sm, La) and SmxCe1-xO2-δ (x = 0, 0.05, 0.1, 0.2, 0.3), Sm0.2Ce0.8O2-δ exhibits the highest surface exchange coefficient, thus should be promise as the anode component. Moreover, it is found that, at temperature below 700°C, surface exchange kinetics at the grain boundary is significantly faster than on the grain, suggesting additional advantage of developing SOFCs by low-temperature sintering.
F577
Lei Ding, Xianfeng Dai, Rui Lin, Haijiang Wang and Jinli Qiao
Carbon-supported CoPc-M (where M = Fe, Co, Ni, V as the second active component) nanoparticle catalysts have been synthesized via a combined solvent-impregnation and milling procedure along with the high-temperature treatment. The effects of metal addition and metal loading on the electrocatalytic activity of carbon-supported CoPc were studied. Both heated and unheated catalysts were characterized by means of cyclic voltammetry (CV) and linear sweep voltammetry (LSV) employing a rotating disk electrode (RDE) in both acid and alkaline solutions to quantitatively obtain the oxygen reduction reaction (ORR) kinetic constants and the reaction mechanisms. The resulting CoPc-Fe/C of 40:60 ratio, heat-treated at 600°C, exhibited promising catalytic performance in terms of the ORR. The optimal loading of Fe was found to be 5 wt% when Fe loading was varied from 1 wt% to 8 wt% nominal. The transferred electron number, n, per oxygen molecule on CoPc-5%Fe/C electrode is in the range of 2.62–2.66 in acid solution and of 3.03–3.54 in alkaline solution compared to pure CoPc/C with the value of n in the range of 2.01–2.14 in acid solution and of 2.7–3.14 in alkaline solution, respectively. XRD, TEM and XPS analysis revealed that dispersion of the particle size of these carbon-supported catalysts is highly improved after modification of 5%Fe, thus the enhanced catalytic activities due to the increase in active centers which might be from the synergistic effect of Co-Nx and Fe-Nx.
F585
J. A. O’Brien, J. T. Hinkley and S. W. Donne
The reaction pathway of sulfur dioxide electro-oxidation on platinum and gold substrates is investigated here using a combination of static and rotating electrode voltammetric methods. A gold electrocatalyst does not need to be sulfur modified in order to display high activity, meaning the substrate is inherently more active than platinum. Analysis of diffusion behavior and reaction order on these substrates suggests that both kinetic and diffusion limitations control oxidation on each electrode. However, it is proposed that a similar oxidation pathway, involving adsorption and subsequent oxidation of sulfur dioxide on the electrode surface, is followed for an activated electrode. Mass changes were monitored at the electrode surface using an electrochemical quartz crystal microbalance, and both in- and ex-situ observations support this pathway proposal.
F594
A. Yu. Zuev, V. V. Sereda and D. S. Tsvetkov
Perovskites based upon substituted LaCoO3−δ are the state-of-the-art materials for a variety of different devices for moderate high temperature applications such as solid oxide fuel cells (SOFCs) and mixed ionic and electronic conducting (MIEC) membranes. The unique feature of the oxides is their ability to undergo both thermal expansion and that induced by the defects of oxygen nonstoichiometry in the oxide lattice. The latter is chemical or defect-induced expansion. This property is extremely sensitive to the defect structure of the oxide material. Therefore reliable data on the defect structure of oxide materials is of key importance to understanding the origin of their chemically induced lattice strain. On the other hand, chemical expansion of oxide crystal cell precisely measured with ppm-resolution allows better understanding its local electronic and defect structure.
F600
Shimaa M. Ali, Yasser M. Abd Al-Rahman and Ahmed Galal
LaFeO3 was prepared by the microwave-assisted citrate method and the catalytic activity for oxygen evolution reaction was investigated in HClO4 solution. The prepared sample was characterized by XRD, HRTEM and FESEM. XRD data showed that pure perovskite phase was indeed formed. The results suggested the successful incorporation of Fe3+ at the La3+ cations sites confirming the formation of the orthorhombic perovskite phase of LaFeO3. The particle size calculated from Scherrer equation was found to be 80.56 nm. The orthorhombic phase and the particle size were also ascertained by the HRTEM picture. FESEM image showed a porous and rough surface. Anodic linear polarization was used to evaluate the catalytic activity. The presence of the perovskite modifier increased the electrocatalytic activity toward oxygen evolution reaction (OER) by about 100 times, the current densities obtained at 1.5 V are 3.6 × 10−5 and 1.2 × 10−3 A/cm2 for unmodified and modified surfaces, respectively. The order of reaction with respect to [H+] is close to unity and the calculated activation energy is 20 kJ/mol, which is much less than the values reported for several catalysts used for OER including some precious metal oxides. EIS results proved the high electrocatalytic activity of LaFeO3 toward OER.
Organic and Bioelectrochemistry
G97
Paula M. V. Fernandes, José M. Campiña, Carlos M. Pereira and Fernando Silva
Electropolymerization from deep eutectic solvents (DES), a green alternative to room temperature ionic liquids, could be a convenient route to the fabrication of organic semiconductors at lower economic and environmental cost which has been barely studied in the literature. This work explores the novel use of choline-based solvents in the electrosynthesis of Polyaniline (PANI), a model conducting polymer. Different mixtures of choline chloride with ethylene glycol (Ethaline), glycerol (Glyceline), and urea (Reline) were prepared for these purposes. PANI was grown and characterized in-situ by Cyclic Voltammetry. Ex situ Scanning Electron Microscopy (SEM) unveiled the formation of dense matrices in the nanoscale from Ethaline and Glyceline but just a bunch of clusters from Reline. The large amounts of ionic and H bond donor species in these formulations, led to conductivities ten times higher than those for aqueous PANI (σ≈63 S·cm−1), great reversibility for the transitions between the different redox states of the polymer (indicating efficient charge transport and low amount of charge traps), and a limited stability toward continuous potential cycling in DES (associated to the increase in the water content). Nonetheless, the latter was significantly improved in aqueous media. More generally, the feasibility of electropolymerization processes using DES is demonstrated.
Physical and Analytical Electrochemistry, Electrocatalysis, and Photoelectrochemistry
H735
Xincun Dou, Rajiv Ramanujam Prabhakar, Nripan Mathews, Yeng Ming Lam and Subodh Mhaisalkar
Zn-doped SnO2 nanocrystals with different doping concentrations were synthesized and the nanocrystal photoanode based DSSC achieved a PCE of 2.07% with a high Voc (0.67 V). TiCl4 modification of the photoanode greatly improves the charge injection efficiency and charge collection efficiency and the resulting PCE increased to 4.32% despite a decreased dye adsorption. The Zn-doped SnO2 nanocrystals will be of particular interest as photoanode material in DSSCs.
H740
Han Wang, Nancy J. Siambun, Linpo Yu and George Z. Chen
A new reference electrode for high temperature molten salts (except for fluorides) was conveniently fabricated by sealing the Ag|Ag+ (AgCl) couple in a commercial alumina tube whose closed end was ground into a membrane (ca. 0.1 mm in thickness) to facilitate ion conduction. Repeated (>15 times) and prolonged continuous (7 days) tests of this reference electrode in molten chloride and carbonate salts confirmed highly satisfactory and robust performance in terms of stability, reproducibility and reusability over a wide range of temperatures (500∼900°C) without any noticeable deterioration. It exhibited ionic resistance (<4 kΩ) decreasing with temperature, but changing insignificantly with the composition of all molten salts tested. A linear relation of potential versus logarithm of mole fraction of NaCl was observed in mixed NaCl-CaCl2 (slope: 0.1603 V/decade). Salt penetration into the membrane was confirmed by scanning electron microscopy, although no through-pores were observed. These findings are discussed in terms of the membrane and liquid junction potentials, and a mechanism of ion conduction through semi-closed pores (fast and ion-non-selective) and grain boundaries (slow and cation-selective) in series.
H747
James K. Kariuki
The development of low-cost and disposable electrodes for diverse electroanalytical applications is an active area of research. There are a number of reports in the literature on the use of disposable pencil graphite electrodes. However, there has not been a systematic study that compares the physical and electrochemical properties of pencil graphite electrodes and the more commonly used glassy carbon (GC) electrode. In this study, pencil graphite electrodes were characterized by X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, scanning electron microscopy (SEM), and the electron-transfer kinetics for Fe(CN)63−/4−, Ru(NH3)63+/2+, Fe2+/3+, and dopamine redox systems. The pencils graphite electrodes tested in this work showed well defined and reproducible voltammetric peaks for all the redox systems studied. The electron-transfer rate of the pencil graphite electrodes was in most cases comparable to that of the more commonly used glassy carbon (GC) electrode. The pencil graphite electrodes should potentially continue to find applications in inexpensive electroanalytical experiments, as well as in diverse electrochemical experiments in teaching laboratories.
H752
Andrew J. Leenheer and Harry A. Atwater
Hydrogen generation by water electrolysis is promising for energy storage, and imaging the reaction dynamics near a H2-evolving electrode can provide valuable insights. We utilized laser-scanning confocal fluorescence microscopy to map the product/reactant concentration at a H2-evolving electrode at micron-scale resolution which identifies areas with fast reaction kinetics. Small concentrations of a pH indicator dye added to the aqueous electrolyte enables ratiometric fluorescence sensing for quantitative pH detection over the range pH 5.3-7.5 and minimally perturbs the local environment. To overcome diffusion limitations, a miniature flow cell was utilized in the microscope to achieve micron-scale resolution in steady state while applying galvanostatic current. We demonstrated the technique using F:SnO2-coated glass with varied metal catalyst patterns and compositions resulting in clear images of increased pH near areas of high water-reducing activity. Simulations of the pH profiles near the electrolyte-patterned catalyst interface were also performed using the COMSOL finite-element software package to solve the convection/diffusion equations, and the calculation results agreed well with the experimentally-observed fluorescence profiles. Flow cell fluoresecence microscopy shows promise in imaging comparative catalyst activity as well as three-dimensional product/reactant profiles in complex electrode architectures.
H758
Julia Agullo, Mario Morin and Daniel Bélanger
The effect of various parameters on the grafting of pyridine, by electrochemical reduction of 3-diazopyridinium cations generated in-situ, on a glassy carbon electrode was investigated. More specifically, the influence of 3-aminopyridine and NaNO2 concentration used for the diazotization reaction and the influence of the grafting conditions such as time and potential used for reduction of the diazonium cations, were investigated by cyclic voltammetry, electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy. The presence of immobilized pyridine at the electrode surface was demonstrated by X-ray photoelectron spectroscopy measurements and indirectly, by the blocking effect of the grafted layer. The best blocking effect is obtained for a diazotization reaction of 1 min. and 1 equivalent of sodium nitrite. As a general observation, when the time is increased and the reduction potential is made more negative, the higher blocking effect that is observed indicates a more compact layer and a higher surface coverage of the glassy carbon electrode. The apparent pKa of the immobilized pyridine was determined by cyclic voltammetry in the presence of Fe(CN)63−/4− solution of different pHs and found to be equal to 5, which is close to the pKa value (5.25) of pyridine in homogeneous solution.