Batteries and Energy Storage
A95
Li Yang, Boris Ravdel and Brett L. Lucht
A98
Shali Zhu, Amy C. Marschilok, Chia-Ying Lee, Esther S. Takeuchi and Kenneth J. Takeuchi
The electrochemical study of silver hollandite is presented, establishing the promise of this material for future secondary battery applications. A low temperature reflux-based strategy for the synthesis of pure silver hollandite is described, where an enhancement in silver loading was achieved relative to other low temperature methods.
A101
Rachid Amine, Ho Hyun Sun, Ho Jin Sun and Jai Prakash
A105
Jing-Jing Ding, Qian Sun and Zheng-Wen Fu
A109
Junyoung Mun, Taeeun Yim, Chang Young Choi, Ji Heon Ryu, Young Gyu Kim and Seung M. Oh
A112
A. Garcia-Gomez, P. Miles, T. A. Centeno and J. M. Rojo
Cylindrical carbon monoliths (7 mm in diameter and 3.9 mm in height) with a microporous structure and compacted pellets derived from the monoliths with the same mass and similar geometric dimensions (6 mm in diameter and 3.2 mm in height) are studied as electrodes in two-electrode supercapacitor cells. The monolith cell shows better electrochemical behavior than the pellet cell, as deduced from its higher capacitance, lower resistance, and shorter response time. The specific capacitance of carbon in monoliths
is compared to that in pellets
and discussed.
A115
Shunsuke Muto, Kazuyoshi Tatsumi, Tsuyoshi Sasaki, Hiroki Kondo, Tetsu Ohsuna, Kayo Horibuchi and Yoji Takeuchi
It is difficult to analyze the local concentrations and chemical states of lithium in lithium-ion secondary battery electrodes by microanalysis techniques based on transmission electron microscopy because the core excitation spectra of transition metals invariably overlap with the absorption/emission spectra of Li–K. We propose a promising analysis method that enables the spatial distribution of lithium with different chemical states from the original phase in a
-based positive electrode to be visualized. It employs a suite of spectrum imaging techniques including scanning transmission electron microscopy, electron energy-loss spectroscopy, and multivariate curve resolution. This method is successfully applied to a cross-sectioned positive electrode.
A118
Xin Hao, Ping Liu, Zhian Zhang, Yanqing Lai, Xinyu Wang, Jie Li and Yexiang Liu
Fuel Cells and Energy Conversion
B83
Rong Lan and Shanwen Tao
On-board hydrogen storage remains a big challenge for fuel cell powered electric vehicles. Ammonia contains 17.6 wt % hydrogen and has been recognized as a potential on-board vehicular hydrogen media. Direct ammonia fuel cells are interesting because they do not require an ammonia cracking process to produce hydrogen, whereas conventional proton exchange membrane fuel cells based on acidic membranes such as Nafion are not compatible with
. Here we report the operation of direct ammonia alkaline anion-exchange fuel cells based on low cost membrane and non-noble catalysts with potential use in transportation and other applications.
B87
R. Küngas, F. Bidrawn, J. M. Vohs and R. J. Gorte
B91
Xingbao Zhu, Zhe Lü, Bo Wei, Yaohui Zhang, Xiqiang Huang and Wenhui Su
B95
Tatsumi Ishihara, Tae Ho Shin, Parichatr Vanalabhpatana, Koji Yonemoto and Maki Matsuka
B98
Elizabeth J. Biddinger, Dieter von Deak, Hilary S. Marsh and Umit S. Ozkan
Rotating ring-disk electrode (RRDE) testing is commonly used for determining the activity and selectivity of oxygen reduction reaction (ORR) catalysts. The effect of RRDE catalyst ink aging on the reported selectivity to water formation was studied for both commercial Pt/Vulcan carbon and nitrogen-containing nanostructured carbon
catalysts. Aging the ink before application could cause a significant improvement in the selectivity measured. While the reasons behind this improvement in selectivity are not yet clear, possible explanations include changes in physical properties of the catalyst, changes in surface hydrophilicity, and changes in surface oxygen functional groups.
Corrosion, Passivation, and Anodic Films
C21
Nabeen K. Shrestha, Min Yang and Patrik Schmuki
Electrochemical/Chemical Deposition and Etching
D61
S.-Y. Han, D.-H. Lee, S.-O. Ryu and C.-H. Chang
D65
Takashi Ohsaka, Katsuhiko Hirano and Shin-ichiro Imabayashi
The present study examined how to minimize the influence of the anodic reaction products by using an ion-exchange membrane to separate the cathode and anode compartments and by changing the anode electrolyte composition. The current efficiency is maintained at 100% for more than 6 times longer period compared to the conventional plating method using a one-compartment cell. The present iridium plating is also superior in crack formation. The addition of glycerol is effective in reducing the crack formation not only in freshly prepared plating baths but also in plating baths used for long periods.
Physical and Analytical Electrochemistry
F7
Kenji Matsubara and Keiko Waki
The effect for oxygen reduction characteristics of O-functionalities formed on the edge planelike defects at the open ends of multiwalled carbon nanotubes (MWCNTs) and at the hole defects on the tube walls was investigated by using the rotating disk electrode technique. The onset potential of the electrochemical reduction of oxygen for MWCNTs shifts to the positive direction of 0.19 V, while the O-functionalities were removed from the defects sites. These results suggest that the control of functional groups is important for the control of the oxygen reduction reaction catalyst activity.
F10
Paul J. Sides, Christopher L. Wirth and Dennis C. Prieve
A method for imaging local electrochemical current density uses light scattered from probe particles proximate to an electrode. A
particle near a working electrode (WE) scattered light more intensely or less intensely as a function of local current density. The light intensity correlated with the measured current. A current density of
was easily resolved. Fair agreement between the measured superficial current density and current density calculated from the light scattering intensity was achieved. The results demonstrate a method for imaging spatially varying electrochemical reaction rates with high resolution.
Dielectric Science and Materials
G65
Tae Joo Park, Keum Jee Chung, Hyun-Chul Kim, Jinho Ahn, Robert M. Wallace and Jiyoung Kim
G68
Jiagang Wu and John Wang
Semiconductor Devices, Materials, and Processing
H257
C. Charbonneau, K. E. Lee, G. B. Shan, M. A. Gomez, R. Gauvin and G. P. Demopoulos
H261
Kwang H. Lee, Aaron Park, Seongil Im, Yerok Park, Su H. Kim, Myung M. Sung and Seungjun Lee
H264
Sung-Min Yoon, Sang-Hee Ko Park, Shin-Hyuk Yang, Chun-Won Byun and Chi-Sun Hwang
To improve the bias stress stability of ZnO thin film transistors (TFTs), a double-layered
gate insulator (GI) prepared by atomic layer deposition was proposed for forming high quality interface and suppressing interdiffusion. The protection layer deposited using water vapor, which also acts as a first GI, plays an important role in improving the bias stability. We obtained excellent characteristics of the ZnO TFT, in which the threshold voltage of 0.65 V and the mobility of
did not show any changes at the stress field of 1.7 MV/cm even after 51,000 s.
H268
Wayne Chen, Winnie V. Chen, Kangmu Lee, S. S. Lau and T. F. Kuech
Ion-cut layer transfer of (110) InP was investigated as an alternative to (100) InP. The use of (110) InP allows for the cleavage plane to be parallel to the substrate surface facilitating transfer. InP donors were pattern-masked, allowing for selective hydrogen implantation. The implanted wafers were bonded to acceptor substrates and transfer was initiated. The surface of the transferred regions was observed to be flatter than those obtained on (100) InP. Hall effect measurements showed the mobility in the masked regions to be unaffected by transfer. The process is extendable to the transfer of finished device structures into integrated systems.
H271
M. B. H. Breese, S. Azimi, Y. S. Ow, D. Mangaiyarkarasi, T. K. Chan, S. Jiao, Z. Y. Dang and D. J. Blackwood
Electrochemical anodization of bulk silicon has applications in many micromachining processes. However, its use for silicon photonics is limited because silicon-on-insulator (SOI) wafers cannot be anodized using a conventional process because of the buried oxide. We overcome this using an alternating potential to induce an ac across an SOI wafer, treating it as a capacitative structure. The resultant surface roughness is comparable to that obtained using conventional anodization, and uniform etching across a 6 mm exposed surface is obtained with a minimum patterned linewidth of
in the device layer.
H274
Dae-Ho Son, Dae-Hwan Kim, Jung-Hye Kim, Shi-Joon Sung, Eun-Ae Jung and Jin-Kyu Kang
H278
Chih-Chien Lin and Ching-Ting Lee
Using a self-shadowing nature, various indium tin oxide (ITO) nanorod arrays were deposited on the surface of GaN-based light emitting diodes (LEDs) by an electron-beam deposition system. The surface morphology and effective refractive index could be controlled by the oblique angle of the deposited ITO nanorod arrays. The surface morphology and the matching refractive index of 1.6 between air and p-GaN layer were obtained for the ITO nanorod arrays with an oblique angle of 45°. Comparing the conventional LEDs without ITO nanorod arrays, the light output power increase of 26.4% is attributed to the surface morphology and the matching refractive index obtained by the ITO nanorod arrays.
H281
H.-Y. Serene Koh, Shu-Lu Chen, Peter B. Griffin and James D. Plummer
We grew SiGe on insulator (SGOI) by the rapid melt growth (RMG) technique. The RMG method combines Si-seeded, defect-necked melt growth with liquid encapsulation by self-aligned silicon dioxide microcrucibles. We obtained high quality, single-crystal, and (100)-oriented laterally graded SGOI structures with this simple and robust process, demonstrating that RMG can be applied to alloys with large miscibility gaps. Our process opens the possibility of building Si-compatible devices that require a smooth lateral variation in bandgap or lattice constant.
H284
Kihoon Do, Dokyu Lee, Dae-Hong Ko, Hyunchul Sohn and Mann-Ho Cho
Changes in volume in
(GST) films due to the density change during phase transformations between amorphous and crystallized states and consequent void formations were examined. Transmission electron microscopy (TEM) was used to measure changes in volume during laser-induced crystallization for both as-deposited and melt-quenched GST amorphous films, and changes in density were estimated. We found the formation of voids and their coalescence during repeated heat cycling by laser. A variation in chemical composition around the voids was confirmed using energy-dispersive spectroscopy analysis. The void formation and compositional changes can lead to degradation of reliability in phase-change random access memory devices.
H287
Young Jae Park, Hyung Gu Kim, Hee Yun Kim, Jae Hyoung Ryu, Hyun Kyu Kim, Ji Hye Kang, Nam Han, Min Han, Bo Hyun Kong, Hyung Koun Cho et al
H290
Dung-Ching Perng, Jia-Bin Yeh, Kuo-Chung Hsu and Yi-Chun Wang
Sensors and Displays: Principles, Materials, and Processing
J89
Tao Chen, Ryoichi Ishihara and Kees Beenakker
J92
Yong-Ho Yang, Kyung-Min Ahn and Byung-Tae Ahn
We have developed a crystallization process, where the crystallization temperature is lowered to the conventional rapid thermal annealing (RTA) process and the metal contamination is reduced compared to the conventional vapor-induced crystallization (VIC) process. a-Si film on the seed layer, which was crystallized by the VIC process, was crystallized by the RTA process at
for 5 min. The poly-Si film appeared as a needlelike growth front with a relatively well-arranged Si(111) orientation. Moreover, the Ni concentration in the poly-Si film was reduced to
. The reduction in metal contamination could be helpful to achieve a low leakage current in poly-Si thin film transistors.
J96
Mutsumi Kimura, Yohei Yamaguchi, Hayami Hashimoto, Masaaki Hirako, Toshifumi Yamaoka and Satoshi Tani
Hall voltage in micro poly-Si Hall cells is evaluated to analyze the Hall effect in poly-Si films and investigate the possibility of magnetic sensors. Normal Hall effect occurs, but the Hall voltage has an offset voltage even when magnetic field is zero, whereas the change in the Hall voltage is proportional to the magnetic field. The offset voltage is caused by the control current flows through zigzag paths due to the random location of polycrystalline grains. These results mean that material evaluation based on the Hall effect is also available for poly-Si films and suggest the possibility of area sensors.
J99
Xiqian Yu, Rui Wang, Yu He, Yongsheng Hu, Hong Li and Xuejie Huang
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K73
Yoon-Chae Nah, Nabeen K. Shrestha, Doohun Kim, Sergiu P. Albu, I. Paramasivam and Patrik Schmuki
When anodic self-organized nanotube layers are formed on valve metals, often a disordered porous initiation layer is present on the tube tops. In the present work, we show that on the
nanotubes this layer can be triggered to self-peel and roll up in the nanosheets if the anodization is carried out at a sufficiently high voltage. An ultrasonic treatment allows to completely remove the nanosheet rolls and to obtain highly ordered nanotube layers. This finding is of high significance for any applications requiring defined tube tops.