Batteries and Energy Storage
A125
G. L. Yang, A. F. Jalbout, Y. Xu, H. Y. Yu, X. G. He, H. M. Xie and R. S. Wang
A129
Yulin Ma, Geping Yin, Pengjian Zuo, Xiaolan Tan, Yunzhi Gao and Pengfei Shi
A132
M. Anji Reddy, V. Pralong, U. V. Varadaraju and B. Raveau
A135
N. K. Karan, J. J. Saavedra-Arias, D. K. Pradhan, R. Melgarejo, A. Kumar, R. Thomas and R. S. Katiyar
A140
Hai-Wei Lu, Le Yu, Wei Zeng, Yue-Sheng Li and Zheng-Wen Fu
A145
Manickam Minakshi, Pritam Singh, Melody Carter and Kathryn Prince
Fuel Cells and Energy Conversion
B127
T. V. Nguyen, G. Lin, H. Ohn and X. Wang
This work presents an experimental method that is one of the few to allow both imbibition and drainage capillary measurement at pressures above breakthrough. It was used on Toray and SGL Carbon gas diffusion materials at room temperature. These materials exhibited both hydrophobic and hydrophilic properties. Breakthrough pressures for Toray and SGL Carbon were 3.6 and
, respectively. Little hysteresis was observed in these room-temperature experiments, which is an interesting contrast with the results from the only other group, Schwartz’s group at University of Washington, to measure these properties. A double exponential equation was used to fit the data for each carbon paper.
B132
Vladimir Gurau, Robert V. Edwards, J. Adin Mann Jr. and Tom A. Zawodzinski Jr.
B136
Cheng-Lan Lin, Carlos M. Sánchez-Sánchez and Allen J. Bard
B140
Zhenguo Yang, Guanguang Xia, Zimin Nie, Joshua Templeton and Jeffry W. Stevenson
B144
J.-M. Klein, M. Hénault, P. Gélin, Y. Bultel and S. Georges
B148
Derek Cheng, Siyu Ye and Előd Gyenge
B153
Yong-Hun Cho, Hyun-Seo Park, Jinho Kim, Yoon-Hwan Cho, Suk Won Cha and Yung-Eun Sung
We conducted performance tests on a polymer electrolyte membrane fuel cell containing a catalyst-coated membrane in which artificial pinholes were introduced. The membrane electrode assembly (MEA) with the punctured membrane showed similar performance behavior to an unblemished MEA in the lower current density region. However, the performance of the pinhole MEA with the punctured membrane in the higher current density region was inferior and unstable. The structures of the defective membrane and the MEA were analyzed by field-emission scanning electron microscopy, and their electrochemical characteristics were investigated by electrochemical impedance spectroscopy and single-cell testing.
B156
Kangli Wang and Jeffrey W. Fergus
The effect of yttria-stabilized zirconia (YSZ) doping on Cr deposition at a Pt-electrode/YSZ-electrolyte interface was investigated. Comparison between undoped and Mn-doped YSZ electrolyte surfaces after cathodic polarization for 25 h in moist air at
in the presence of chromia indicated that the presence of Mn in the electrolyte significantly enhances Cr deposition at the electrode/electrolyte interface. Impedance spectroscopy results showed that with a Mn-doped YSZ electrolyte the electrode polarization resistance decreased significantly with polarization time, which was attributed to the increase in the three-phase boundary length by the p-type semiconducting chromia deposits.
B161
J. J. Pietron, Y. Garsany, O. Baturina, K. E. Swider-Lyons, R. M. Stroud, D. E. Ramaker and T. L. Schull
Corrosion, Passivation, and Anodic Films
C47
N. T. Wen, F. J. Chen, M. D. Ger, Y. N. Pan and C. S. Lin
The microstructure of trivalent chromium conversion coating on electrogalvanized steel plate has been characterized. The as-deposited coating consisted of three layers with a thin inner layer, a porous intermediate layer, and a thin outer layer. Baking at
for 30 min reduced the population density and size of cracks in the coating. Meanwhile, the outer layer became denser, but the immediate layer became highly porous. During baking at elevated temperatures, the chemical species and voids within the coating redistribute, which, in turn, suppresses the formation of microcracks that are commonly seen in the hexavalent chromium counterpart.
Electrochemical/Chemical Deposition and Etching
D65
R. J. von Gutfeld and Alan C. West
An in situ method of plating onto aluminum using a laser to remove the surface oxide is described. The aluminum, acting as a cathode, in conjunction with a counter electrode (anode), is submerged in a copper or nickel plating solution with a small potential between them. A laser pulse is directed through the electrolyte onto the substrate in a single or several 10 ns pulses of 532 nm light. Adherent plating occurs only in the region where the light impinged to remove the inhibiting aluminum oxide. The technique opens the way for film depositions on aluminum without preprocessing steps.
Dielectric Science and Materials
G41
Yuan-Chang Liang, Yung-Ching Liang and J. P. Chu
Semiconductor Devices, Materials, and Processing
H207
Chi-Feng Weng, Ting-Chang Chang, Han-Po Hsieh, Shih-Ching Chen, Wei-Che Hsu, Wang-Chuang Kuo and Tai-Fa Young
In this work the characteristics of p-type polysilicon thin-film transistors (poly-Si TFTs) with dynamic bias stress were investigated. The ac stress is operated with the constant drain voltage (15 V) and the varying gate voltage (0 V to −15 V) to degrade the devices. Because the self-heating effect could raise channel temperature, the Si–H bonds at the poly-
interface were broken due to Joule heating. The released hydrogen reacts with
and causes the fixed charge in the gate oxide. Thus, the degradation of electrical characteristics of the device is mainly dominated by the self-heating-induced negative-bias-temperature instability effect.
H210
Jaeyeong Heo, Seok-Jun Won, Dail Eom, Sang Young Lee, Young Bae Ahn, Cheol Seong Hwang and Hyeong Joon Kim
Nucleation of the ruthenium (Ru) precursor on low-
film surfaces during atomic layer deposition (ALD) of Ru was investigated. The adsorption tendency of the precursor decreased with increasing concentration of methyl groups on the low-
film surface, resulting in poor nucleation of Ru. The electron-deficient hydroxyl groups act as preferential adsorption sites for the electron-rich ligands of the aromatic Ru precursor through the formation of π-bonds. This leads to the enhanced nucleation of Ru. The roles of the functional groups were corroborated by silylation experiments.
H214
T. Sun and A. Philipossian
A method using spectral analysis of friction data is established to determine the tribological mechanism of post-interlevel dielectric (post-ILD) chemical mechanical planarization (CMP) brush scrubbing as a function of solution pH, pressure, and tool kinematics. Spectral analysis based on real-time raw friction data is used to quantify the total amount of mechanical interaction in the brush-fluid-wafer interface in terms of stick-slip phenomena. Friction force variance
criterion is established to determine the tribological mechanism during scrubbing, and compared to the classical method by constructing and interpreting Stribeck curves.
H218
H. Y. Noh, Y. G. Seol, S. I. Kim and N.-E. Lee
Improvement of dispersion of the
nanoparticles in the poly(4-vinyl phenol) (PVP) matrix by coupling agent treatment resulted in a reduction of the leakage current density of the nanocomposite gate dielectric in organic thin-film transistor (OTFT) devices, which, in turn, improved the device performance compared to that of the device with the pure PVP gate dielectric. Under repetitive cyclic bending, the leakage current density of the nanocomposite layer was not changed, while that of the PVP layer was increased significantly. The nanocomposite gate dielectric layer provided the flexible OTFT device with improved mechanical and electrical stabilities.
H222
Hsiao-Wen Zan and Kuo-Hsi Yen
A simple UV-treatment process for poly(methyl methacrylate) (PMMA) dielectric is proposed to enhance photoresponsivity of pentacene-based organic thin-film transistors. The UV treatment creates excess negatively charged sites on the PMMA dielectric, which makes the device exhibit a large photoinduced current and prolongs persistent conductance recovery. In order to describe time-dependent photoinduced current, double-time constant equations are proposed. Based on time-constant fittings, slow-varied responses are found to be influenced by the UV treatment. The rapid-varied response is independent of gate bias and UV treatment. A plausible model for spatial carrier distribution is discussed and proposed to describe this observed phenomenon.
H226
Jae-Wan Park, Min Kyu Yang and Jeon-Kook Lee
H230
Woei-Cherng Wu, Tien-Sheng Chao, Te-Hsin Chiu, Jer-Chyi Wang, Chao-Sung Lai, Ming-Wen Ma and Wen-Cheng Lo
H233
Han Zhao, Davood Shahrjerdi, Feng Zhu, Hyoung-Sub Kim, Injo OK, Manhong Zhang, Jung Hwan Yum, Sanjay K. Banerjee and Jack C. Lee
H236
Monali B. Joshi, Sumiko L. Hayashi and Mark S. Goorsky
A transfer-enhanced semiconductor substrate has been demonstrated, integrating a thin InP layer on a Si handle substrate with an imbedded porous silicon layer. A Si wafer was anodized to create a low-density porous surface layer. A thin layer of InP was transferred to the Si handle substrate through wafer bonding and hydrogen-induced exfoliation. High-resolution X-ray diffraction, atomic force microscopy, and transmission electron microscopy characterization showed the structure to have high surface and crystalline quality for epitaxial deposition after undergoing chemical mechanical polishing. Layer transfer capability was demonstrated with a similar structure by mechanical fracture through the porous Si layer.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K73
J. R. Rani, V. P. Mahadevan Pillai, C. S. Suchand Sandeep and Reji Philp
-doped Si nanorings with an outer diameter of 25 nm and an average width of 5 nm are grown by pulsed laser deposition. Atomic force microscopy reveals several interesting self-assembling forms of polycrystalline as well as an amorphous type of silicon nanorings. Depending on the width of the ring, the optical bandgap and photoluminescence can be tuned from the near infrared (1.38 eV) to the ultraviolet (3.02 eV), giving evidence for the strong quantum confinement effect along the width of ringlike quantum states. From Z-scan studies, the two-photon absorption coefficient is determined to be
.
K78
Yu Mizoguchi and Shinobu Fujihara
K81
Z. R. Scheibal, W. Xu, J. F. Audiffred, J. E. Henry and J. C. Flake
Electrografting provides a method for the direct (Si–C) covalent functionalization of silicon surfaces. In this work, cathodic electrografting of hexynoic acid to silicon nanowire surfaces and subsequent immobilization of bovine serum albumin (BSA) is demonstrated. Hexynoic acid was cathodically electrografted to dense arrays of silicon nanowires approximately 50–100 nm in diameter and
in length. Protein immobilization was achieved via amidization reactions with carboxylic moieties of electrografted hexynoic acids. Results include chronoamperometric data from the electrografting process and verification of attachment using attenuated total reflectance Fourier transform infrared spectroscopy (FTIR) of electrografted hexynoic acid and immobilized BSA. In addition to FTIR analysis, covalently immobilized BSA was verified using fluorescence microscopy and solution-phase fluorescence.