Regular Papers & Short Notes
Semiconductors
7175
Kensuke Nishioka, Nobuhiro Sakitani, Ken-ichi Kurobe, Yukie Yamamoto, Yasuaki Ishikawa, Yukiharu Uraoka and Takashi Fuyuki
We have evaluated the influence of grain boundaries on the temperature dependence of cell performance using a modified 2-diode equivalent circuit model. In this model, microscopic inhomogeneity of resistivity at or near grain boundaries can be taken into consideration. The calculated results by the modified 2-diode model agreed well with the measured current-voltage curves, and the validity of the fitting parameters in this model was discussed. One of the fitting parameters, r is defined as the ratio of the recombination area, in which the recombination of minority carriers is pronounced. At 20°C, r of the polycrystalline Si cell was larger than that of the single-crystalline Si cell. However, the difference in r between them became negligible at temperatures above 80°C. These dependences were explained by considering the behavior of the free carriers in the recombination centers.
7180
Sejoon Lee, Young Suk Shim, Hoon Young Cho, Deuk Young Kim, Tae Whan Kim and Kang L. Wang
Si nanocrystals were formed using a Pt nanoscale island etching mask. A high-resolution transmission electron microscopy image showed that the Si nanocrystals were created inside a SiO2 layer, and the cathodoluminescence spectrum showed that the luminescence peak is related to the Si nanocrystals. Capacitance-voltage measurements on Al/SiO2/nanocrystalline Si/SiO2/p-Si structures at 300 K showed that the value of the flatband voltage shift increased parabolically with increasing Si nanocrystal size. These results indicate that Si nanocrystals can be formed using a Pt island etching mask and that the magnitude of the flatband voltage shift for the Al/SiO2/nanocrystalline Si/SiO2/p-Si structures is significantly affected by the size of the Si nanocrystals embedded in the SiO2 layer.
7184
Eddy Simoen, Joan Marc Rafí, Cor Claeys, Vlad Neimash, Anatolii Kraitchinskii, Mykola Kras'ko, Valerii Tischenko, Vasyl Voitovych, Jorg Versluys and Paul Clauws
This work describes the radiation defects formed in high-temperature (450°C) 1 MeV electron-irradiated n-type Czochralski (Cz) silicon. A dedicated irradiation configuration has been used, which relies on sample heating by the energy deposited by the electron beam current. It is shown that the vacancy oxygen (VO) or A center is the dominant radiation defect under these circumstances. In addition, a whole series of unknown deep electron traps is reported, whose trap parameters (activation energy, electron capture cross section) depend, among other factors, on the starting interstitial oxygen concentration. It is speculated that their origin is related to complexes of oxygen and vacancies.
7189
Woo-Suk Sul, Sam-Dong Kim, Hyung-Moo Park and Jin-Koo Rhee
We examine the effects of thin-film passivation on the DC, RF and noise characteristics of 0.1-µm-gate-length pseudomorphic high-electron-mobility transistors (PHEMTs) when either conventional Si3N4 or low-dielectric-constant benzo-cyclo-butene (BCB) is used for the passivation layer. A significant shift in pinch-off voltage of ∼-0.4 V is observed from the PHEMTs after the Si3N4 passivation, whereas no such variation in DC parameters is observed in the case of BCB passivation. Noise figures of the devices are very stable after the BCB passivation and are only ∼60% of those in the case of Si3N4 passivation when measured at 55–62 GHz. Other RF parameters are not significantly affected by the passivation materials at a frequency of 50 GHz. We propose that the degradation in DC and noise characteristics can be due to the high density of surface states in the Si3N4 passivation layers; on the other hand, excellent stability in electrical characteristics in the BCB passivations can attribute to the minimized surface states in the passivation layer.
7194
Shigenobu Sugita, Yasumasa Watari, Ginga Yoshizawa, Jun Sodesawa, Hiroshi Yamamizu, Kuan-Ting Liu, Yan-Kuin Su and Yoshiji Horikoshi
We have successfully grown Be-doped p-type GaN on a sapphire (0001) substrate by radio frequency plasma assisted molecular beam epitaxy (RF-MBE) by conserving the surface polarity during growth. It is found that while the surface polarity of undoped GaN grown on a sapphire (0001) substrate is N-terminated, it changes from N- to Ga-terminated during the growth of Be-doped GaN. When this polarity change occurs, the resistivity of the grown layer is extremely high. Moreover, a broad deep level photoluminescence distinctly appears around 2.0 eV. When an AlN buffer layer is used, a GaN layer on this buffer layer can be grown under the Ga-terminated condition. By growing Be-doped GaN on the Ga-terminated GaN, we have successfully grown Be-doped p-type GaN without the polarity change. In addition, the optical property of the sample is markedly improved. We have confirmed that the Be acceptor level is shallower than the Mg acceptor level by approximately 100 meV.
7198
Masaki Shima, Masao Isomura, Ken-ichiro Wakisaka, Kenji Murata and Makoto Tanaka
Ways of improving the deposition rate of hydrogenated amorphous silicon germanium (a-SiGe:H) while maintaining its film quality, using the very high-frequency plasma-enhanced chemical vapor deposition (VHF-CVD) technique, were investigated. It was concluded that the VHF-CVD technique with a high hydrogen dilution of silane and germane is suitable for high-quality a-SiGe:H fabrication at a relatively high deposition rate. The reason why the high deposition rate is compatible with high quality is related to the high density of hydrogen radicals, which are proper to the VHF-CVD technique. The low plasma potential of VHF plasma contributes to high-quality a-SiGe:H film deposition by suppressing ion bombardment and excessive penetration of hydrogen atoms into the film. In device fabrication, the VHF-CVD technique is also useful because a high deposition rate with low ion bombardment may suppress negative effects to the underlying layers during deposition of the a-SiGe:H photovoltaic layer. This investigation showed that almost the same initial and stabilized efficiency for an a-Si/a-SiGe tandem solar cell was obtained at a five times higher deposition rate for the a-SiGe:H photovoltaic layer than those in conventional RF-CVD methods using the same reaction chamber.
7205
Toshihide Nabatame, Tetsuji Yasuda, Masayasu Nishizawa, Minoru Ikeda, Tsuyoshi Horikawa and Akira Toriumi
We systematically investigated the oxygen diffusion in both amorphous and γ-Al2O3 films using 18O as a tracer and observing depth profiles by secondary ion mass spectroscopy. The oxygen diffusion coefficients for amorphous Al2O3 films were two or three orders of magnitude larger than those of the γ-Al2O3 films. The activation energies of about 1.2 eV for both films were considerably lower than those for bulk α-Al2O3. These results could be explained by the difference in Al2O3 structure: α-Al2O3 has a dense corundum structure while γ-Al2O3 has a defective spinel structure with cation site vacancies. We found that the amorphous Al2O3 films prepared by atomic layer deposition could function as a barrier layer against oxygen diffusion only within a limited range of heat treatment conditions.
7209
Noriaki Kawamoto, Miki Fujita, Tomohiko Tatsumi and Yoshiji Horikoshi
Epitaxial ZnO films have been grown on Si(111) substrates by molecular beam epitaxy using oxygen plasma. An initial Zn layer deposition followed by its oxidation produces a superior template for the subsequent ZnO growth and a low-temperature ZnO buffer layer improves the structural and optical properties of ZnO films. As a result, we succeeded in growing high-quality ZnO films directly on Si substrates. We observed cracks composed of straight lines along the principal axes of the Si(111) surface. These cracks are probably caused by the difference in thermal expansion coefficient between ZnO and Si. X-ray diffraction measurements reveal that ZnO films do not include a rotational domain and the full width at half maximum of the diffraction peak of ZnO(0002) is 0.23 deg. The linewidth of the neutral-donor-bound exciton emission at 3.365 eV is as small as 6 meV at 10 K.
7213
Ming-Kwei Lee, Tsung-Hsiang Shih, Hsin-Fu Huang, Shyh-Jen Wei and Chung-Min Shih
Tellurium-doped n-type GaAs0.6P0.4/GaAs with a carrier concentration of 1017 cm-3 was used as the substrate for the heteroepitaxial growth of ZnSxSe1-x by metalorganic vapor phase epitaxy. The mirror-like surface morphology of lattice-matched ZnS0.47Se0.53 on GaAs0.6P0.4/GaAs was obtained. The hillock density increased with x deviating from 0.47. ZnS0.47Se0.53 lattice-matched to a GaAs0.6P0.4/GaAs substrate showed a strong peak with a full width at half maximum (FWHM) of 28 meV. The emission centered at 490 nm seemed to be favored at high Se/Zn ratios. This was considered to be associated with the Zn vacancy.
7217
Doo Soo Kim, Sejoon Lee, Cheonki Min, Hwa-Mok Kim, Sh. U. Yuldashev, Tae Won Kang, Deuk Young Kim and Tae Whan Kim
(Zn1-xMnx)O diluted magnetic semiconductors (DMSs) grown on (0001) Al2O3 substrates by radio frequency magnetron sputtering were investigated with the aim of producing a material with a high ferromagnetic transition temperature (Tc). X-ray diffraction, photoluminescence, and Hall-effect measurements showed that the grown (Zn1-xMnx)O thin films were p-type crystalline semiconductors with single phases. Magnetization curve as a function of magnetic field at 5 K indicated that ferromagnetism existed in the (Zn1-xMnx)O thin films, and magnetization curve as a function of temperature showed that the Tc of the (Zn0.93Mn0.07)O thin film was 70 K. These observations can improve the understanding of the increase in Tc for (Zn1-xMnx)O DMSs grown on (0001) Al2O3 substrates.
7221
Yasuyuki Miyamoto, Ren Yamamoto, Hiroshi Maeda, Katsuhiko Takeuchi, Nobuya Machida, Lars-Erik Wernersson and Kazuhito Furuya
To apply the ballistic nature of hot electrons, an InP hot electron transistor with a buried metal (BM-HET) is reported. In this device, carriers are extracted from the emitter by an attractive potential originating from an embedded metal grating, and they propagate through intrinsic semiconductor material only. A simple estimation shows a high cutoff frequency and low output conductance. The estimated highest cutoff frequency is approximately 1 THz. Fabricated devices show that the collector current increased with the gate bias. After extraction of the leakage current, a clear saturation of the collector current in common-emitter characteristics was confirmed and the possibility of BM-HET as a candidate for high-speed electron devices was demonstrated.
7227
Ming-Jang Lin, Tsung-Hwang Lee, Fang-Long Chang, Chorng-Wei Liaw and Huang-Chung Cheng
Superjunction devices are reported to provide better high-voltage operation characteristics than conventional abrupt junction devices in silicon power applications. In this study, the superjunction reduced surface field (SJ-RESURF) lateral double diffused metal oxide semiconductor field effect transistor (LDMOSFET) is fabricated on a bulk silicon wafer to improve the operating characteristics of high-voltage devices. By introducing the p-type strips in the drift region, higher doping concentration of the drift region can be adopted to reduce the conduction resistance. The SJ-RESURF LDMOSFET with a specific on-resistance of 3.53 Ω·mm2, a breakdown voltage of 335 V and a drift length of 30 µm, is demonstrated; its turn on-resistance is 25% better than that of the conventional structure. The turn-on resistance, breakdown behavior, device geometry, temperature, and charge balance mechanics of the SJ-RESURF LDMOSFET are examined herein.
7232
Hung-Der Su, Bi-Shiou Chiou, Chin-Yuan Ko, Shien-Yang Wu, Ming-Hsung Chang, Kuo-Hua Lee, Yung-Shun Chen, Chih-Ping Chao, Yee-Chaung See and Jack Yuan-Chen Sun
The breakdown detections of ultrathin oxide (1.4–2 nm) using a fast voltage ramp have been studied. It was found that the breakdown voltage test of deep sub-micron technology requires the reduction of the gate area of test patterns and therefore the increase of the number of structures due to a large inversion gate current at a low electrical field (>0.1 A/cm2 at 1 V) caused by the scaling down of oxide thickness. The gate current in accumulation mode is smaller than that in inversion mode by more than two orders of magnitude at a low applied voltage (1 V). The bi-mode model proposed in this paper applies a voltage stress in the inversion mode and detects failure in the accumulation mode to enhance the robustness of the breakdown test and reduce the possibility of pseudo breakdown failure. With the proposed method, a shorter test time with an increased test pattern area to improve the efficiency of the breakdown test of ultrathin oxide is achieved.
7238
Hideaki Tsuchiya, Motoki Horino, Matsuto Ogawa and Tanroku Miyoshi
The quantum transport properties of nanoscale silicon-on-insulator (SOI) metal-oxide-semiconductor field-effect transistors (MOSFETs) are investigated based on a quantum Monte Carlo (MC) device simulation. Quantum mechanical effects are incorporated in terms of a quantum correction of potential in well-developed particle MC computational techniques. The ellipsoidal multivalleys of the silicon conduction band are also considered in the simulation. First, the validity of the quantum MC technique is verified by comparing the simulated results with those calculated by a self-consistent Schrödinger–Poisson method at thermal equilibrium. Then, the nonequilibrium quantum transport characteristics of nanoscale SOI-MOSFETs are demonstrated. Furthermore, a quasi-ballistic behavior of ultrashort-channel devices is studied by evaluating the frequency of carrier scattering events in the channel region.
7244
Satoshi Miyamura, Yuhki Kasai, Youichi Yamamura, Takao Inokuma, Koichi Iiyama and Saburo Takamiya
The electronic states of Ga-terminated and As-terminated GaAs(100)-(1×1) surfaces and those surfaces with adsorbed O and S are studied by molecular orbital calculation using small cluster models and the discrete variational Xα method. Without adsorption of any foreign atoms, the Ga-terminated surface has 4p-related surface states in the middle of the forbidden band. While, the As-terminated surface has 4p-related surface states in the lower half of the forbidden band. The adsorption sites of chalcogen atoms on Ga- and As-terminated surfaces are determined ab initio by using density functional theory (Gaussian 98). With adsorbed chalcogen atoms, the density of the surface states in the forbidden band of the surface Ga layer markedly decreases, and that of the surface As layer increases. The adsorbates have states in the lower half of the band gap (Ga-terminated surface) or in the valence band (As-terminated surface). The results suggest that a chalcogen adsorbed Ga-terminated and bare As-terminated surface have low surface densities in the upper half of the band gap.
7250
Kosuke Tatsumura, Takanobu Watanabe, Daisuke Yamasaki, Takayoshi Shimura, Masataka Umeno and Iwao Ohdomari
By simulation of silicon oxidation and measurement of X-ray crystal-truncation-rod (CTR) scattering, the structures of silicon dioxide films grown at different temperatures and the structural changes due to thermal annealing have been investigated. Large-scale SiO2/Si(001) models were formed by introducing oxygen atoms, atom-by-atom, in crystalline Si from the surfaces. Molecular dynamics (MD) calculation at a constant temperature was repeatedly carried out for the growing oxide model. The intensity and position of the extra diffraction peak observed for the oxide, correlating with the residual order emanating from the parent Si crystal, depend on the growth temperature and change after thermal annealing. The peak intensity becomes smaller with increasing growth temperature. Thermal annealing monotonically decreases the peak intensity and shifts the position along the CTR, toward the lower angle side. There is a good agreement between the results of simulation and experiment. It is shown that (1) the oxide grown at a higher temperature has a lower degree of residual order, (2) thermal annealing decreases the residual order, ultimately leads to complete amorphization and never restores the ordering, and (3) the peak shift along the CTR corresponds to the volumetric expansion of the SiO2 in the surface-normal direction.
7256
Sungjoo Lee and Dim-Lee Kwong
In this paper, we report the electrical characteristics of n- and p-metal oxide semiconductor field effect transistors (MOSFETs) fabricated using a high-quality ultrathin (equivalent oxide thickness ∼11 Å) chemical vapor deposition (CVD) HfO2 gate stack with a selfaligned dual poly-Si gate process. The CVD HfO2 gate stack exhibits excellent thermal stability with the poly-Si gate up to 1050°C, after 30 s annealing. Good output MOS characteristics with high drive current capability, excellent subthreshold swings, and good mobility are obtained from both n- and p-MOSFETs.
7259
Ara Philipossian and Erin Mitchell
The residence time distribution of slurry in the pad-wafer interface was experimentally determined and used to calculate the slurry utilization efficiency (η) of the chemical mechanical planarization (CMP) process. Slurry utilization efficiency represents the percentage of slurry that actually participates in the polish by entering the region bounded between the wafer and the pad. Results show that η ranges from 2 to 22%, depending on operating conditions such as applied wafer pressure, relative pad wafer velocity, slurry flow rate and pad surface texture (i.e. type of pad grooving).
7265
Seiichi Shishiguchi, Akira Mineji and Tomoko Matsuda
In this work the transient enhanced diffusion (TED) induced by point defects due to source/drain implantations is investigated and an optimized process to realize shallow junctions and suppress TEDs in p-channel metal–oxide–semiconductor field-effect-transistors (PMOS-FETs) is proposed. The TED of boron or phosphorus associated with the source/drain implantations has been evaluated by secondary ion mass spectroscopy (SIMS) analyses of isotopic borons and blurred δ-doped marker-layer profiles. Low-energy boron implantations at energies lower than 0.5 keV reduce both the TED and the junction depth in PMOS-FETs, which is recommended for the S/D extensions. Germanium pre-amorphized boron implantations effectively reduce the TED due to the higher energy boron implantation for the deep-S/D formation.
7272
Masato Aoki, Hisanori Yamane, Masahiko Shimada, Seiji Sarayama, Hirokazu Iwata and Francis J. Disalvo
The dissolution mass of GaN in molten Na at 650–800°C and 3–5 MPa of N2 was determined by weight loss of polycrystalline GaN fragments immersed in Na and by chemical analysis of the amount of Ga dissolved in Na. The dissolution of GaN in Na was equilibrated within 100 h and the dissolution mass increased with increasing temperature but decreased with increasing N2 pressure. It was found that the addition of a small amount of Li3N into the Na melt increased the dissolution mass of GaN. Transparent platelet single crystals of GaN with sizes over 300 µm were grown from nutrient GaN powder by cooling a Na solution with a Li3N additives from 800°C to 700°C at 1°C/h.
7276
Takeyoshi Onuma, Shigefusa F. Chichibu, Toyomi Aoyama, Kiyomi Nakajima, Parhat Ahmet, Takashi Azuhata, Toyohiro Chikyow, Takayuki Sota, Shin-ichi Nagahama and Takashi Mukai
Optical and structural properties of an InGaN double-quantum-well (DQW) laser diode (LD) wafer that lased at 450 nm were investigated to discuss an enormous impact of a polarization-induced electric field on the recombination dynamics in InGaN quantum structures. The quantum-well (QW) structure was shown to have the well thickness as thin as approximately 1 nm and InN molar fraction x of approximately 14%. The gross effective electric field in the QW (FQW) was estimated to be 490 kV/cm from the Franz–Keldysh oscillation (FKO) period in the electroreflectance (ER) spectrum, implying that an internal piezoelectric field (Fpiz) of approximately 1.4 MV/cm was cancelled by the pn junction built-in field (Fbi) and Coulomb screening due to carriers in the DQW. The magnitude of FQW can be further weakened by applying reverse bias (VR) on the junction; the decrease in the photoluminescence (PL) lifetime at low temperature measured under VR was explained to be due to a recovery of electron-hole wavefunction overlap for small VR (|VR|<4 V), and due mainly to the tunneling escape of carriers through the barriers for larger VR. By applying an appropriate VR smaller than 4 V, electron-hole wavefunction overlap, which had been separated vertically along the c-axis due to quantum-confined Stark effect, could be partially recovered, and then the time-resolved PL signals exhibited a less-pronounced stretched exponential decay, giving a scaling parameter (β) of 0.85 and effective in-plane localization depth (E0) of 40–50 meV for the spontaneous emission. These values were closer to those of much homogeneous QWs compared to those reported previously for InGaN QWs having similar InN molar fractions. The use of very thin QWs is considered to bring easier Coulomb screening of FQW and population inversion under high excitation conditions.
7284
Ashraful Ghani Bhuiyan, Tatsuya Tanaka, Ken Kasashima, Akihiro Hashimoto and Akio Yamamoto
Epitaxial InN films have been grown on sapphire substrate by using an ArF excimer laser-assisted metalorganic vapor-phase epitaxy (LA-MOVPE) as a new potential growth technique. An ArF excimer laser photolytically dissociates NH3 with independent of the growth temperature while photolytical dissociation of trimethylindium (TMI) is not observed. The photolytically dissociated NH3 reacts with TMI to deposit InN film and even single crystalline film is grown. This enables InN film deposition over a wide range of growth temperature, from a room temperature to a very high temperature (700°C). Single crystalline InN films with smooth surfaces are successfully grown in the temperature range of 350-700°C with a variety of condition. The characterization of the InN films grown over a wide range of temperature and condition enables to find out some important evidences about the InN properties, especially the band gap energy. Interestingly, this new growth technique provides a growth rate of more than 0.5 µm/h just by flowing a very little amount (∼100 sccm) of NH3. While to obtain such growth rate in our conventional MOVPE a total amount of ∼6000 sccm NH3 gas is required. The electrical properties are still found to be poor compared to the recently reported good results. Important evidences as to what species is responsible for poor electrical properties in the grown InN are discussed.
7290
Chunlong Li, Xiangyang Ma, Jin Xu, Xuegong Yu, Deren Yang and Duanlin Que
The effect of rapid thermal process (RTP) on oxygen precipitation in heavily boron-doped (HB) Czochralski (CZ) silicon (Si) wafers has been investigated. After RTP preannealing at high temperature, it was found that, contrary to lightly boron-doped (LB) silicon, a denuded zone (DZ) was not formed in the HB silicon. The oxygen precipitates and extended defects generated in the HB Si samples were smaller than those generated in the LB Si samples. It is considered that DZ formation by means of RTP may not be suitable for HB CZ silicon.
7292
Toetsu Shishido, Shigeru Okada, Yoshio Ishizawa, Kunio Kudou, Kiyokata Iizumi, Yutaka Sawada, Hiroyuki Horiuchi, Katsuhiko Inaba, Takashi Sekiguchi, Jinhua Ye et al
Single crystals of CrSi2 were obtained in the form of hexagonal prisms by a high-temperature solution growth method using molten tin as a solvent. Their maximum dimensions were approximately 0.3 mm in diameter and 2.5 mm in length. The crystals had hexagonal symmetry with space group P6222 and their lattice parameters were a=0.425(2) nm and c=0.6375(1) nm. The crystals were semiconducting. The value of the micro-Vickers hardness for the {1100} face with hexagonal symmetry was 11.2±0.4 GPa. The weight gain of the crystals heated to 1473 K in air was negligible.
7294
Tsunenobu Kimoto, Kouichi Hashimoto and Hiroyuki Matsunami
Homoepitaxial growth of 4H-SiC(1120) and (0338) by hot-wall chemical vapor deposition has been investigated. Both the residual-donor concentration and deep-level concentrations can be reduced by increasing the C/Si ratio during growth. The optimum C/Si ratio for obtaining high-quality epilayers with good morphology is higher on the non-basal planes than on off-axis (0001). The correlation between deep levels and growth condition is discussed.
Magnetism
7296
Jongill Hong and Hitoshi Kanai
A sub-monolayer of Co90Fe10, Ni80Fe20, Ta, Cu or Ru was investigated for a spin valve having a Co90Fe10 free layer. The sub-monolayers of Co90Fe10, Ni80Fe20, Cu and Ta did not significantly improve the giant magnetoresistance of the spin valve, probably because the spin-dependent scattering due to localized potentials at the Fe impurity in a Co free layer, rather than scattering at the other impurities, dominates the spin valve's magnetoresistance response. As a result of this dominance, the effect of such a sub-monolayer cannot be pronounced. However, since there was some improvement in all but one case, the results clearly confirm that such a layer can play a role as a spin-dependent scatterer. In the case of Ru, the sub-monolayer greatly decreased the giant magnetoresistance value, and this is direct evidence that Ru is indeed a suppressor of bulk spin-dependent scattering.
7299
Osamu Kohmoto
Effective demagnetizing factors (Nxe, Nye) of single-crystal films having cubic or uniaxial anisotropy are derived by new Nxe and Nye equations for the use of Kittel's ferromagnetic resonance formula. Nxe and Nye are obtained by one kind of first derivative (∂G/∂θ). Both first-order and second-order magnetocrystalline anisotropy constants are treated. Six arrangements of films with the static field along the film normal are calculated: (1) perpendicular uniaxial anisotropy, (2) in-plane uniaxial anisotropy, (3) cubic-crystal (001) face, (4) cubic-crystal (011) face, (5) cubic-crystal (111) face, and (6) oblique anisotropy.
Optics and Quantum Electronics
7304
Jongbae Kim, Jung Jin Ju and Min-su Kim
A theoretical model is unprecedentedly formulated for the macroscopic description of an electric field and an induced second-order nonlinearity by periodic poling in a waveguide. A fundamental field distribution between a set of two electrodes with a finite width is first proposed and then, by using linear superposition and electrode periodicity, the net electric fields generated in the waveguides are derived explicitly. A mean distribution of quasi phase matching and a generalized electrode width are introduced to analyze the poling-induced characteristics of the second-order nonlinear coefficient. Four types of poling schemes, depending on the electrode structure, are discussed from a quantitative viewpoint of calculating a quasi phase matching efficiency in the periodic poling and thus enhancing the conversion efficiency in a nonlinear optical phenomenon. The maximized efficiency and the corresponding optimized width of the shortened electrode are determined in poling experiments by means of the present approach.
7313
Tomotaka Yamazaki, Takasumi Tanabe, Fumihiko Kannari, Yasunari Shida and Shigeo Fushimi
This work proposes a backward propagation solver based on the Fourier transform method. To deliver ultrashort optical pulses through single-mode optical fibers, it is necessary to calculate the precise spectral phase and amplitude of the input pulse, which are required to compensate for the pulse broadening due to dispersion and self-phase modulation during fiber propagation. We numerically demonstrate that transform-limited pulses are obtainable by fiber delivery at an energy of up to 5 nJ, 75 fs pulses at 800 nm through a 1 m standard fiber, and of 6-dBm-power, 10 Gbps, 50% duty pulses at 1.55 µm through a standard fiber 80 km long.
7318
Kazunori Tanimura, Tsuyoshi Konishi, Yoshinori Oshita, Wanji Yu, Kazuyoshi Itoh and Yoshiki Ichioka
We propose a new method using analysis before acquisition (here, we call it the preprocessing method) to inhibit the influence of the properties of the detector in pulse measurement. We introduce concepts of optical signal processing into the pulse measurement system to realize the preprocessing method. Optical spectrogram scope (OSS) proposed by us is a pulse measurement system based on an optical correlation technique using an optical filtering technique, which enables the introduction of various processing methods into the OSS system by designing the optical filter. In this paper, we propose the preprocessing method using OSS, and demonstrate the sensitive detection of a transitional spectral pattern as an example of the pulse measurement using the preprocessing method.
7326
Takumi Fujiwara, Takashi Sawada, Tsuyoshi Honma, Yasuhiko Benino, Takayuki Komatsu, Masahide Takahashi, Toshinobu Yoko and Junji Nishii
The origin and properties of second-harmonic generation (SHG) from crystalline particles and their crystalline phases in GeO2–SiO2 glass films were investigated. GeO2–SiO2 glass films with a thickness of approximately 5 µm were fabricated by the chemical vapor-phase deposition (CVD) method. Heat treatments in the temperature range of 1100–1260°C for durations of 2–8 h have been performed to crystallize the glass films. X-ray diffraction (XRD) peaks at around 2θ=22° in the crystallized GeO2–SiO2 films were observed, and the obtained XRD patterns in the glass films are exactly the same as those in ultraviolet (UV) poled GeO2–SiO2 glasses with a large second-order optical nonlinearity comparable to that in LiNbO3 crystals. Using a SHG microscopic technique, it has been found that the intensity of SHG emission from crystalline particles is clearly dependent on stress-induced optical retardation which is accompanied by the formation of crystalline particles of the pseudo-β-cristobalite containing GeO2. In addition, a new technique for enhancing the intrinsic SHG by means of modification of defect states is demonstrated.
7331
Yu Tanaka, Yoshimasa Sugimoto, Naoki Ikeda, Tao Yang, Kiyoshi Asakawa, Yoshinori Watanabe, Kuon Inoue, Taishi Maruyama, Kazuya Miyashita and Koji Ishida
The oxidation process applied to the fabrication of an oxide-cladding two-dimensional AlGaAs-based photonic crystal waveguide with tapered ridge waveguides is thoroughly investigated. Combining an extremely small amount of oxidation with the tapered ridge waveguides yielded the self-aligned selective oxidation without any masking layers. This tapered ridge waveguide with partial oxidation functions like a spot size converter that reduces propagation loss and, more importantly, lessens the significant strain induced by oxidation. On the other hand, satisfactory agreement between transmission measurements of fabricated samples and three-dimensional finite-difference time-domain calculations demonstrates the high quality of the photonic crystal slab waveguide.
7339
Yoshihiro Uozu and Kazuyuki Horie
A plastic rod-lens array that we developed industrially with a continuous spinning technique has an optical resolution of 200 dpi (4 lp/mm), and it has been used for facsimile machines and other applications. However, this resolution is still insufficient for its application in image scanners, copy machines, and light emitting diode (LED) printers. During the study for improving the optical resolution of the plastic rod-lens array, we have confirmed that this resolution is determined by the deviation of refractive index distribution from the ideal one at the outer circumferential part. Therefore, we have developed a technique for dyeing the outer circumferential part of the rod lens in order to achieve the higher optical resolution power of 300 dpi (6 lp/mm).
7344
Andy Y.-G. Fuh, Chia-Yu Lu, Ting-Shan Mo and Ming-Shann Tsai
Dynamic holography and polarimetric methods are used to study torques on liquid crystals exerted by photo excited dyes doped in planar nematic liquid crystal (NLC) films. The dye used is methyl red (MR). The dynamical reorientation of liquid crystal directors induced by photo-excited dyes is examined. The results indicate that the dynamics include the initial transient reorientation, followed by the transient three-dimensional rotation, and finally the stable LC alignment parallel to the optical field. A model is presented to explain these results. Quantitative analyses of the grating dynamics yield the dye-diffusion coefficients in the directions parallel and perpendicular to the LC director.
7349
Dae-Jin Kim, Seong-Eun Park, Hyun-Jung Kim, Je-Kil Ryu, Byungsung O and Sung-Sik Pak
Polycrystalline gallium nitride (GaN) thin films of thickness 3.0 µm grown on silica glass substrates were annealed by a line beam of a KrF excimer laser under vacuum. The applied laser energy density was in the range of 300–600 mJ/cm2. Photoluminescence (PL) and X-ray diffraction (XRD) measurements have been carried out to investigate the laser annealing effects in polycrystalline GaN films grown on silica glass by metal-organic chemical vapor deposition (MOCVD). The results of the PL spectra revealed that the intensity of the band edge (BE) emission for the GaN on silica glass annealed at a laser energy density of 500 mJ/cm2 was increased by as much as about 1.5 times in comparison with the as-grown GaN. It was found that the full width at half maximum (FWHM) of the XRD for laser annealed GaN film at a high laser energy density, 500 mJ/cm2, with 200 pulses was smaller than that of the as-grown GaN. These results indicate that the structural and optical properties of the poly-GaN layers grown on silica glass substrate are improved by the laser annealing method.
7354
Jorge Niedbalski
The influence of the dielectric material and the dependence of parameters (pressure, voltage, etc.) on the development of volumetric gas discharges as photoionization sources in a capacitively coupled (electrode-dielectric-screen) assembly were investigated. Two materials with very different permittivity values and high contrast in their hysteresis effects were tested in assemblies excited by high-voltage pulses with a rise time of about 5 ns within the range 5–11 kV. Discharges in nitrogen and neon gases were characterized in detail through the measurements of current and emitted light to establish the necessary conditions for an optimized performance (uniformity and intensity) of irradiation. A comparison between the two assemblies as to the production of phototriggered discharges within regions behind a single and a double screen subjected to a uniform electric field was performed.
7361
Seo Hern Lee, Hee Wook Do, Gi-Dong Lee, Tae-Hoon Yoon and Jae Chang Kim
Based on the horizontal switching principle, the optical configuration of a reflective in-plane-switching (IPS) liquid crystal device is proposed for high-contrast and high-brightness operation. In the proposed configuration, in order to reduce saturation voltage and increase reflectance, we optimized the liquid crystal parameters such as rubbing angle, electrode gap, dielectric anisotropy, and twist elastic constant. In order to investigate the validity of the proposed reflective IPS liquid crystal device, we fabricated a test cell and obtained a contrast ratio of 23:1.
7366
Hiroyuki Mochizuki, Masuki Kawamoto and Tomiki Ikeda
In order to lower the operating voltage of molecularly doped electroluminescent (EL) devices using a low-molecular-weight liquid crystal (LC), we added a small amount of electrolytes (tetrabutylammonium bromide: TBAB) to the EL devices. The addition of TBAB decreased the driving voltages by one order of magnitude. Furthermore, the EL devices containing TBAB could be operated under not only a dc mode but also an ac mode.
7368
Yueh Ouyang, Ching-Cherng Sun, Chih-Yuan Hsu and Hon-Fai Yau
A novel active filter for transmission light modulation based on a vibration-controlled beam fanning along the c-axis in BaTiO3 is proposed and demonstrated. To the best of our knowledge, it is the most efficient method of controlling the fanning effect in a photorefractive crystal with a large gain in two-wave mixing.
Optical Properties of Condensed Matter
7370
Der-Jun Jang, Wu-Ching Chou, Chu-Shou Yang, Chie-Tong Kuo and Meng-En Lee
The hot carrier dynamics of ZnCdSe epilayers were studied using the femtosecond time-resolved photoluminescence up-conversion technique. The hot carriers release the excess energy primarily through scattering with longitudal optical phonons. The optical phonon emission times of the hot carriers were fitted from the carrier cooling curves and found to be 40 ps for both samples with different Cd concentrations. The initial temperature To was estimated below the theoretical calculation due to the fact that these hot carriers reach thermal equilibrium in a time scale faster than the experimental temporal resolution. The hot phonon effect is not prominent in the present work for the excitation density of 1017 cm-3.
7373
Nobuyuki Yokosawa and Eiichiro Nakazawa
The photoluminescence of YAl3(BO3)4:Eu3+ phosphor is sensitized by the codoping of Gd3+ ions under ultraviolet excitation from 130 nm to 160 nm. The Gd3+ ions sensitize the emission of Eu3+ ions by a two-step energy transfer from the host to Gd3+ and then to Eu3+ ions.
7376
Kee-Sun Sohn, Deuk-Kyu Hwang and Jae-Min Myoung
ZnO films were deposited on sapphire (0001) and single crystalline GaAs (001) substrates using a metal-organic chemical vapor deposition (MOCVD) technique, and systematically analyzed in terms of time integrated and resolved photoluminescence (TIPL and TRPL) as well as electrical properties. The TIPL, TRPL and electrical properties showed significant differences depending on the nature of the substrate. The correlation between TIPL, TRPL and electrical properties was also investigated based on defects in the ZnO films.
7379
Raghu Nath Bera, Youichi Sakakibara, Madoka Tokumoto and Kiyoshi Yase
Energy transfer and concentration quenching for a red-emitting electroluminescence system, tetraphenylchlorin (TPC)-doped tris(8-hydroxyquinoline)aluminum (Alq3) at various concentrations, were studied using a time-resolved photoluminescence (PL) technique. The PL decay of Alq3 in the presence of TPC was observed to be non-exponential in nature due to the Förster-type energy transfer from Alq3 to TPC. The PL decay of TPC became faster with the increase in TPC concentration due to the concentration quenching of TPC emission.
7381
Chikara Onodera, Tadayoshi Shoji, Yukio Hiratate and Tsunemasa Taguchi
The enhancement of exciton binding energy was clearly observed with increasing cadmium (Cd) alloy content in CdxZn1-xS/ZnS quantum wells (QWs). However, the maximum exciton binding energy saturated at high Cd alloy content. The amount of decrease in exciton binding energy decreased with increasing Cd alloy content under an electric field.
Electrical Properties of Condensed Matter
7383
Masashi Mikami, Masashi Yoshimura, Yusuke Mori, Takatomo Sasaki, Ryoji Funahashi and Masahiro Shikano
We measured and analyzed the electrical resistivity (ρ), Hall coefficient (RH), Seebeck coefficient (S) and magnetic susceptibility (χ) of γ-phase Na0.6CoO2 and α-phase Na0.9CoO2 crystals prepared by solution growth using NaCl-Na2CO3-B2O3 fluxes. The ρ of α-phase Na0.9CoO2 (ρα) is much higher than that of γ-phase Na0.6CoO2 (ργ), while the magnitude of S of α-phase Na0.9CoO2 (Sα) exceeds that of γ-phase Na0.6CoO2 (Sγ). The origin of these differences is primarily the difference in carrier density. In addition, ρα has a minimum at around 20 K, while ργ exhibits a metallic temperature-dependence throughout the measured temperature range. Since α-phase Na0.9CoO2 exhibits an antiferromagnetic transition at the same temperature 20 K, the increase in ρα at low temperatures implies the carrier localization effect caused by forming a long-range order among magnetic moments in the conductive CoO2 layer.
7387
Hui-Dong Li, Chu-De Feng and Ping-Hua Xiang
(1-x)(Na1/2Bi1/2)TiO3–xBaTiO3 (x=0.06) with 0–5 at.% lanthanum was prepared by the conventional mixed oxide method. The effect of La3+ doping on dielectric and piezoelectric properties of the ceramics was studied. The ceramics' relaxor behavior is more distinct after La3+ doping. At room temperature, the dielectric constant is increased. When the La content is less than 1.5 at.%, the piezoelectric properties are enhanced. Meanwhile the dielectric loss of the ceramics is also increased. When the content of La3+ is higher than 1.5 at.%, the ceramics' piezoelectric properties are considerably degraded.
7392
R. R. Vedantam, V. Subramanian, V. Sivasubramanian and V. R. K. Murthy
The dielectric dispersion of the solid solutions (Pb1-xBax)(Zn1/3Nb2/3)O3 and (Pb1-xSrx)(Zn1/3Nb2/3)O3 with x=0.2 and 0.3 has been studied as a function of temperature for the frequency range 0.1 to 200 kHz. The variation in the relaxor nature between the studied compounds is discussed using the generalized Curie–Weiss law. The paper also discusses the variation in the relaxation mechanism in these compounds with Barium and Strontium substitution using Vogel–Fulcher relation and power law. Detailed analysis of power law shows that Barium substituted Pb(Zn1/3Nb2/3)O3 exhibits stronger dielectric relaxation than Strontium substituted Pb(Zn1/3Nb2/3)O3.
7397
Joon Yeob Cho, Ki Hyun Yoon and Eung Soo Kim
The layered Mg0.93Ca0.07TiO3–(Ca0.3Li0.14Sm0.42)TiO3 ceramics were prepared by the spark plasma sintering technique, and the effect of thermal strain on the microwave dielectric properties was investigated. Neither the secondary phase nor the active ionic diffusion through the interface between the two systems was found, which resulted from the rapidly increasing temperature and short sintering time of the spark plasma sintering. The dielectric constant of the specimen was changed by the dielectric mixing rule in addition to the relative density that was increased up to 98% of the theoretical density with an increase of sintering temperature and time. The quality factor showed a relatively high value of 8,650 GHz compared with that of 7,900 GHz of the layered structure specimens with similar relative densities sintered under atmospheric pressure. The quality factor decreased with an increase of induced thermal strain to each dielectric layer, which resulted from the difference in thermal expansion coefficient between the two systems during the cooling process after sintering.
7401
Hajime Nagata, Masaki Yoshida, Yoichi Makiuchi and Tadashi Takenaka
A lead-free piezoelectric ceramic ternary system based on bismuth sodium titanate, (Bi1/2Na1/2)TiO3 (BNT) - bismuth potassium titanate (Bi1/2K1/2)TiO3 (BKT) - barium titanate BaTiO3 (BT) near the morphotropic phase boundary (MPB) between the tetragonal and rhombohedral phases has been investigated. In the case of a(Bi1/2Na1/2)TiO3–bBaTiO3–c(Bi1/2K1/2)TiO3 [BNBK(100a/100b/100c)] solid solution ceramics, the highest piezoelectric constant d33=191 pC/N, Curie temperature, Tc=301°C, electromechanical coupling factor, k33=0.56 and dielectric constant, ε33T/ε0=1141 are observed for the BNBK(85.2/2.8/12) composition which has a tetragonal phase near the MPB. The d33 value is the highest so far reported for all lead-free piezoelectric ceramics with Tc>300°C. The BNT-BKT-BT ternary ceramics system sintered at 1200°C for 2 h in air has a pure perovskite structure and a high density more than 95% of the theoretical density.
7404
Rong-Jun Xie, Yoshio Akimune, Ruiping Wang, Naoto Hirosaki and Toshiyuki Nishimura
Highly dense piezoelectric ceramics of tungsten bronze-type (Sr1.9Ca0.1)1-0.5xBaxNaNb5O15 (where x=0.1–0.8) were prepared by spark plasma sintering. The crystallographic parameters, dielectric behaviors and piezoelectric properties of the sintered ceramics were investigated, and the effects of the Ba substitution on these electrical properties were discussed. The structural analysis and the electrical property measurements indicate a morphotropic phase boundary (MPB)-like phenomenon at x=0.4–0.5. In all compositions, a diffuse phase transition and a relaxor behavior are observed. The electrical properties are found to be crystallographically dependent.
7410
Yiping Guo, Ken-ichi Kakimoto and Hitoshi Ohsato
Ba6-3xSm8+2xTi18O54 (x=2/3) microwave dielectric ceramics with a tungstenbronze-type like structure were synthesized by a spark plasma sintering (SPS) technique. Sintering was conducted under vacuum at temperatures ranging from 1100°C to 1200°C under 60 MPa. The microstructure and phase identification were analyzed by scanning electron microscopy (SEM) and X-ray powder diffraction (XRPD), respectively. The density of the sintered ceramics increased with an increase in temperature. Specimens with a density 98% of the theoretical density could be attained by sintering at 1200°C for 5 min with a heating rate of 200°C/min. Only a tungstenbronze-type like phase was identified in ceramics sintered at temperatures above 1100°C. Microwave dielectric properties also increased with sintering temperature, the sample sintered at 1200°C for 5 min exhibited superior microwave dielectric properties, such as dielectric constant εr=81.2, quality factor Q×f=10099 GHz and temperature coefficient τf=-17.2 ppm /°C. The results indicated that this technique was an alternative sintering method for synthesizing dense microwave dielectric ceramics at a rather low temperature and in a short time.
7414
Ming-Li Hu, Long-Jang Hu and Jenq-Yang Chang
We report here the polarization switching properties of pure and MgO-doped LiNbO3 crystals measured directly by applying an external electric field at room temperature. From hysteresis measurements, the ferroelectric intrinsic coercive fields are found to be decreased when the MgO concentration is increased. Spontaneous polarization is insensitive to the nonstoichiometric composition. The stability time of domain switching is strongly dependent on the MgO doping level. The strength of the internal field related to the non-stoichiometric defect will be discussed.
7418
Andrew J. Bell and Eugene Furman
A two order parameter thermodynamic model is proposed which accounts for a number of features of the solid solution system Pb(Zr1-xTix)O3 not predicted by the conventional 6th order model. The free energy comprises three sets of terms: two expansions of polarization, representing contributions to the polarization of each of the solid solution end-members, weighted linearly with respect to composition, plus terms representing the coupling between the two contributions. Employing previously published coefficients for PbTiO3 and values extrapolated from Zr-rich PZT compositions for PbZrO3, calculations predict that the composition of the morphotropic phase boundary between the rhombohedral and tetragonal phases lies at x=0.45 and is independent of the strength of coupling between the two order parameters. The model allows for the existence of a monoclinic phase, the composition range of which depends upon the strength of the coupling terms. A satisfactory fit to the lattice parameters of Pb(Zr0.52Ti0.48)O3 is obtained over a wide range of temperature.
7424
Yu Zhong, Guangda Hu and Ting-Ao Tang
La modified Sr0.8Bi2.2Ta2O9 (SLBT) thin films were fabricated on Pt/Ti/SiO2/Si substrates by metalorganic decomposition. All the films were annealed at 800°C using a rapid thermal annealing furnace. X-ray diffraction analysis indicated that single-phase layered perovskite SLBT ferroelectric thin films can be obtained and no secondary phase was found. The crystallization and hysteresis behavior of SLBT films showed a dependence on the La content. An increase of Pr and decrease of Ec with increasing La concentration were observed. The fatigue properties were found to be improved when more La was added to SLBT films. The results were discussed with respect to the effects of La3+ and Bi3+ substitution at perovskite A-site.
7428
Ying-Hao Chu, Su-Jien Lin, Kuo-Shung Liu and I-Nan Lin
The dielectric properties of Ba(Mg1/3Ta2/3)O3 (BMT) microwave thin films synthesized by an in situ pulsed-laser deposition (PLD) process were compared with those prepared by a two-step PLD process. The onset of crystallization for the BMT films is approximately 400°C, when in situ deposited, and is approximately 550°C, when two-step processed. Dielectric measurements indicate that complete crystallization for BMT films can be achieved only by processing the films at a sufficiently high temperature, which is 600°C for an in situ PLD process and is 800°C for a two-step PLD process. The microwave dielectric properties of BMT films, which were directly measured by an evanescent microwave probe (EMP) technique at 2.65 GHz measuring frequency, increase with substrate temperature, resulting in dielectric constant K=33.3 and dissipation factor tan
δ =0.0158.
7432
Toru Mori, Akinobu Shibuya and Shintaro Yamamichi
Pb(Zr,Ti)O3 (PZT) thin film has been crystallized at below 450°C by means of a sol–gel process that employs a PT-seeding method, and it has been used to fabricate a PZT thin-film capacitor on polyimide film at a high decomposition temperature. The capacitor structure includes a 4-layer bottom electrode: Pt(200 nm)/Ti(50 nm)/Mo(600 nm)/Ti(50 nm). Capacitance density is 12 nF/mm2 in the effective capacitance area. Despite the use of PZT, a high-k material, this thin-film capacitor still offers high insulation resistance (6.2 GΩ at 3 Vdc) and reliability sufficient for use as a decoupling capacitor.
7436
Hirofumi Takahashi, Shintaro Tsukamoto, Jinhao Qiu, Junji Tani and Toru Sukigara
It was shown in the previous work that the hybrid sintering process using microwave heating and hot-pressing offers advantages over the conventional technologies in the fabrication of piezoelectric ceramics. On the basis of these, the authors predicted that the hybrid process might be applied to the fabrication of the ceramic composite from small single crystal grains and powder of relaxor-type material. In this study, the fabrication of a ceramic composite consisting of 0.79PNN–0.21PT (PNN–PT) single crystals in a 0.5PNN–0.15PZ–0.35PT (PNN–PZT) ceramic powder using the hybrid process is investigated and the results demonstrate the feasibility of the hybrid process for the fabrication of ceramic composites. The specimen fabricated by the hybrid sintering process has a clear boundary between the single crystals and the ceramic matrix but almost no clack. The ratio of the ingredients changes more significantly in the specimens fabricated by the hybrid sintering process from their initial ratio than that in the conventionally sintered specimens. The increase of Zr in the single crystal of the ceramic composite sintered by the hybrid process is due to the diffusion of Zr from the ceramic matrix.
7440
Seunghee Lee and Yongrae Roh
Micro-strip line inductors and capacitors for surface acoustic wave (SAW) duplexers are analyzed and experimented in this study. For SAW duplexers, micro-strip line lumped elements must have small impedance values, below several tens of nH and pF, in small area. Flat line, meander line and spiral line inductors and interdigital capacitors on a LiTaO3 piezo-crystal are theoretically analyzed. In order to accurately evaluate small values of the lumped elements, a measurement method with a network analyzer is proposed. Through the experiment, the validity of the theoretical analysis method is confirmed. The analysis method in this paper can be applied to SAW duplexers as well as other microwave devices.
Structure and Mechanical and Thermal Properties of Condensed Matter
7445
Shinichirou Oka, Kazuya Kobayashi, Yoshihisa Iwamoto, Yasuo Toko, Munehiro Kimura and Tadashi Akahane
The important characteristics for display applications such as the response time, the color shift and viewing angle characteristics of the in-plane switching twisted nematic mode (IT mode) were investigated by means of experiments and numerical simulations. It was found that the fast response time of the IT mode approaches 10 ms, which is not inferior to that of a conventional twisted nematic mode. Based on the results, we emphasize that the IT mode can lead to the realization of excellent LCDs with a small color shift and wide viewing angle characteristics.
7452
Chang-Jae Yu, Sin-Doo Lee, Jung-Il Jin and Jae-Hoon Kim
The dielectric anomaly in ferroelectric liquid crystals exhibiting polarization sign inversion has been studied as a function of temperature under an applied electric field. In such a system, the dielectric anomaly was introduced into a model of a dynamically fluctuating mixture of two interconvertible conformers, whose relative densities depended on temperature and external field. In the frame of the model, it was explained that dielectric constant increased after the suppression of the Goldstone mode by applying an electric field over a certain critical field. It was also found that the induced effective dipole moment, deduced from the field dependence of the dielectric constant, can be described by the simple power law as a function of temperature.
7456
Yuichi Morishita and Keiji Tanaka
Structures in Co-doped SiO2–GeO2 glass with rod and fiber forms have been investigated comparatively to understand their optical properties. The rod exhibits marked light scattering, which can be related to grains of ≃1 µm which contain nanoscale crystalline Co2SiO4 particles. In both the rod and the fiber, Co-related structural fluctuations on the scales of 3 nm are detected by small-angle X-ray scattering. The reason why the crystal exists only in the rod is considered thermodynamically.
7461
Letian Zhang, Wenfa Xie, Jian Wang, Aiwu Li, Hua Xing, Wei Zheng, Ying Qian, Jian Zhang and Yushu Zhang
The influence on the structural and optical properties of Ge-doped flame hydrolysis silica glass films of KrF excimer laser irradiation was investigated. A maximum refractive index change of about 3.41× 10-3 is obtained at approximately 1550 nm after 10 min irradiation. The irradiation process and roughness of the films were analyzed by atomic force microscopy (AFM). As irradiation time increased, the density of the films increased, resulting in decreases in the surface roughness and increases in the refractive index of the films.
7464
Toetsu Shishido, Kunio Kudou, Takahiko Sasaki, Shigeru Okada, Jinhua Ye, Kiyokata Iizumi, Akiko Nomura, Takamasa Sugawara, Kazuo Obara, Masahiko Tanaka et al
The search for a perovskite-type new boride in the Sc–Ni–B system has been carried out by the arc-melting synthetic method. As a result, the chemical formula of the compound ScNi3B0.5 was obtained for the first time. This compound has the cubic perovskite-type structure (space group: Pm3m) with the lattice parameter a=0.37760(7) nm. ScNi3B0.5 exhibits metallic behavior down to 4.2 K. The magnetic susceptibility of ScNi3B0.5 shows Pauli paramagnetism. No superconductivity appears down to the lowest temperature as determined by electric and magnetic measurements. The micro-Vickers hardness and oxidation resistivity in air are also reported for ScNi3B0.5.
7467
Yuzuru Miyazaki, Tatsuro Miura, Mitsuko Onoda, Masaya Uchida, Yoshinobu Ishii, Yasuhiro Ono, Yukio Morii and Tsuyoshi Kajitani
We have determined the crystal structure of novel thermoelectric compound [Ca2(Co0.65Cu0.35)2O4]0.63CoO2 by a superspace group approach. Structural parameters have been refined with a superspace group of C2/m(1 p 0)s0 using powder neutron diffraction data collected at 293 K. The compound consists of mutually interpenetrating triangular CoO2 layers and distorted four-layered rock salt-type Ca2(Co0.65Cu0.35)2O4 slabs, which are incommensurate parallel to the b-axis. The CoO2 layer is composed of the CdI2-type edge-shared CoO6 octahedra. Both the subsystems have common a- and c-axes, and β-angle with a=4.8212(4) Å, c=12.7671(8) Å and β=93.93(1)°. The b-axis lengths are b1=2.8103(3) Å for the [CoO2] subsystem and b2=4.4915(3) Å for the [Ca2(Co0.65Cu0.35)2O4] subsystem. A marked displacive modulation of the (Co,Cu) and O sites in the [Ca2(Co0.65Cu0.35)2O4] subsystem has been observed, yielding a large fluctuation of the (Co,Cu)–O distances in the range from 1.8 Å to 2.7 Å. Cu2+ ions appear to play an important role in stabilizing such a four-atom thick subsystem in this compound.
Surfaces, Interfaces, and Films
7474
Nikolay Oleynik, Armin Dadgar, Jürgen Bläsing, Marco Adam, André Krtschil, Daniel Forster, Frank Bertram, Anette Diez, Markus Seip, Arnd Greiling et al
High-quality ZnO was grown by metal organic vapor phase epitaxy on 1.3 µm thick GaN layers on Si(111) using dimethylzinc and tertiary-butanol as precursors. The variation of the growth temperature shows a strong correlation with the microstructure as observed by atomic force and scanning electron microscopy. With increasing growth temperature we find an increasing size of ZnO crystallites and a transition from 3D to 2D growth. Moreover, increasing the growth temperature leads to a reduction of tensile stress in the ZnO as observed by X-ray diffraction. In highly spatially resolved cathodoluminescence measurements we observe narrow (A0,X) luminescence from the ZnO surface and a strong donator correlated luminescence at macroscopic defects.
7478
Kota Sato, Eiji Shinagawa, Kenji Nakajima, Kaori Miyazaki and Hideomi Koinuma
Hydrogen plasma treatment of a highly oriented pyrolytic graphite (HOPG) surface induces a marked change in the growth of a-Si:H film by glow-discharged decomposition of SiH4. Scanning tunneling microscope (STM) observation verified that the inhomogeneous islandlike growth on as-cleaved HOPG became homogenous after the surface was treated with hydrogen plasma. This drastic change in the surface chemical process could be reasonably interpreted by the ab initio molecular orbital calculations performed on the following reaction models: (1) C24H12 + H → HC24H12 and (2) HC24H12 + SiH3 → HC24H12SiH3. A stable energy minimum was obtained for H addition. H addition to the HOPG surface causes radical formation on the neighboring sp2 carbons, which were in turn spontaneously attacked by SiH3 radicals in the plasma to initiate homogeneous a-Si:H film growth. Without hydrogen plasma treatment, SiH3 radicals would attack the highly conjugated sp2 carbon surface. Therefore, a-Si:H film growth is presumed to be initiated at sparsely distributed defect sites that induce island growth.
7482
Yukihiro Hayashi, Akira Sakai, Hiroya Ikeda, Shigeaki Zaima and Yukio Yasuda
We have studied the surfactant effects of adsorbed oxygen layers of 1-2 monolayer thicknesses on the film evolution of CoSi2(001) in reactive deposition epitaxy at 470°C on Si(001). The O atoms segregating to the growth front play essential roles in suppressing the Si outward diffusion from the substrate and Co lateral migration, which promote two-dimensional layer growth of CoSi2(001) films and make the surfaces smooth. A kinetic mechanism is suggested in which Co atoms easily diffuse without interaction through the O layers toward the substrate and react with Si atoms. Nevertheless, {111}-twinned CoSi2 is formed at the very initial growth stage on O-adsorbed Si, similarly to that on clean Si. We have also investigated the morphology and crystallinity of ∼20-nm-thick CoSi2(001) films. The O atoms remaining on the surface effectively restrain film surface roughening even at this thickness; however, they cannot lower the interface roughness owing to the formation of {111} facets and {111}-twinned boundaries. The twin boundaries formed in the initial stage grow into the substrate during the epitaxy.
7489
Koichi Tamura, Yuki Kimura, Hitoshi Suzuki, Osamu Kido, Takeshi Sato, Toshiaki Tanigaki, Mami Kurumada, Yoshio Saito and Chihiro Kaito
Ultrafine particles of various metals [Cr, Mn, Fe, Al, Ni, Cu, In, Si, Ge, Zn, Mg and Sn], produced by the gas evaporation method were covered with the oxide layer of thickness less than 10 nm by exposure to air. In order to clarify the structure and thickness of the surface oxide layer on various metal ultrafine particles, high-resolution electron microscopy and infrared spectroscopy have been extensively used.
7493
Isao Takahashi, Tositeru Kada, Kouji Inoue, Amane Kitahara, Hiromitsu Shimazu, Norihisa Tanaka, Hikaru Terauchi, Syuichi Doi, Kenji Nomura, Naoki Awaji et al
For ultrathin oxynitride layers 2.4 nm thick, X-ray crystal truncation rod (CTR) scattering is conducted to investigate the interface structures between oxynitride and Si(001). (004) and (202)CTRs showed that the [amorphous oxide]/Si(001) interface is hardly varied by NO-nitrided oxynitridation. On the other hand, (111)CTR indicated that epitaxial oxide crystallites in the matrix of amorphous oxide layer are significantly affected by nitrogen: It is very likely that nitrogen atoms at the interface are captured by these crystallites after their migration on the interface. As interstitial atoms, the adsorbed nitrogen makes the crystallites amorphous. Such an annihilation of the crystallites should be responsible for the high performance of oxynitride as gate oxides. Further oxynitridation where the nitrogen concentration reaches 4 at.% showed a distinct variation in (111)CTR, indicating the creation of a novel structural order at the interface. Such a structural order is likely to be nucleated by the excessively concentrated nitrogen. A close relationship between the novel structural order and degradation of the over-oxynitrided layers is strongly suggested.
7497
Joon-Shik Park, Seung-Hyun Kim, Hyo-Derk Park, Jowoong Ha and Sung-Goon Kang
The microstructures and electrical properties of thin and thick Pb(Zr0.52, Ti0.48)O3 (52/48 PZT) films for microdevice applications with thicknesses from 480 nm to 2.3 µm on 350 nm Pt(111)/40 nm Ti/300 nm SiO2/Si 525 µm substrates fabricated by a sol–gel multicoating process were investigated. These PZT films showed dense and homogeneous surface microstructures. The crystalline structures of 480-nm-thick PZT films showed a (111) preferred orientation over (100), (200) and (110) orientations. The intensity ratios of (100) and (200) to (111) increased at PZT film thicknesses greater than 480 nm. By Auger electron spectroscopy, small-composition-variation peaks at an interval of approximately 120 nm at interfaces produced by each PZT coating process of 480 nm PZT films were found. Dielectric constants increased from 825 to 880 at 100 kHz and PZT film thicknesses from 480 nm to 2.3 µm. The Pr and Ec of 2.3-µm-thick PZT films were about 30 µC/cm2 and 58 kV/cm, respectively. The e31,f of 1-µm- and 2-µm-thick PZT films was characterized by the fabricated e31,f measurement system before and after poling.
7502
Yu-Lung Chin and Bi-Shiou Chiou
The effects of underlayer dielectric on the thermal characteristics and electromigration resistance of copper interconnects are investigated. It is shown that the thermal impedance of metal lines on polyimide is about three times that of metal lines on plasma-enhanced chemical vapor deposition of tetraethylorthosilicate (PETEOS) oxide. The open-circuit failure occurs after 75 s stressing at a current density of 1.4×107 A/cm2 for polyimide underlayer specimens due to the high joule heating effect which causes the extreme temperature rise at interconnects. Hence, decomposition of polyimide occurred which further accelerated the breakdown of interconnects. The thermal impedance is one of the major factors causing the electrical resistance to change during the electromigration (EM) test. The activation energies for electromigration of Cu are 0.87 eV for SiO2/Cu/PI2610 and 0.65 eV for SiO2/Cu/SiO2. After 500 thermal cycles, both the mean time-to-failure (MTF) and activation energy Ea decrease for EM, and lognormal standard deviation increases. At 225°C, the MTF of SiO2/Cu/PI2610 is about two times longer than that of SiO2/Cu/SiO2.
7510
Zhuguo Li, Shoji Miyake, Masao Kumagai, Hidenori Saito and Yukihisa Muramatsu
Ti-Si-N films containing 0–20 at.% Si were deposited on positively biased Si(100) substrates by dc magnetron cosputtering. The growing films were irradiated by an electron flux, instead of the normally energetic ions. X-ray diffraction (XRD) and X-ray Photoelectron Spectroscopy (XPS) results suggested that a metastable Ti(Si)N solid solution with a cubic B1 NaCl-type structure existed in the films containing <10 at.% Si. With the further addition of Si, the films were characterized as having a two-phase structure, consisting of Ti(Si)N and amorphous Si3N4. The columnar morphology of pure TiN with a preferred orientation of the (111) crystal plane was found to transform into a globular one with random orientation only after the appearance of amorphous Si3N4. Although the positively biased grown films have very small compressive stresses (<0.5 GPa), film mechanical properties were improved by the addition of a small amount of Si. Additionally, film tribological property was also enhanced in the case of positive biases.
7516
Yeon-A Shim, Chang-June Yoo, Jong-Ha Moon, Byung-Teak Lee, Sang Sub Kim and Jin Hyeok Kim
A highly (00l) oriented Pb(Mg1/3Nb2/3)O3 (PMN) thin film was successfully grown on a TiN buffered Si(001) substrate. The TiN buffer layer was epitaxially grown with an orientation relationship of [110](001)TiN∥[110](001)Si on Si(001) by pulsed laser deposition. The PMN films were deposited using a radio-frequency magnetron sputtering technique at 500–700°C. The crystallinity, epitaxial nature and microstructures of the fabricated multi-films were investigated using X-ray diffraction and transmission electron microscopy. It was found that a PMN thin film deposited at 650°C shows a dense columnar structure with preferential (001) orientation suggesting the possibility of growing epitaxial PMN thin films on Si substrates using a TiN buffer layer.
7520
Masato Ofuji, Katsuhiko Inaba, Kazuhiko Omote, Hajime Hoshi, Yoichi Takanishi, Ken Ishikawa and Hideo Takezoe
Surface morphology, crystal lattice spacings and crystallite size of copper phthalocyanine (CuPc) thin films grown on rubbed surfaces were probed at different stages of growth, by means of atomic force microscopy (AFM) and X-ray diffraction (XRD). The films consisted of many slender crystallites extending along the rubbing direction, due to the α-type columnar structure along the same direction. AFM revealed that the aspect ratio of crystal domains increases as the films grow, implying a change in the ratio of crystal growth rates in the two different directions parallel to the substrates. XRD demonstrated marked differences in the two intercolumnar directions. The molecular spacing is expanded in the thickness direction at the initial stage of growth, while it remains constant throughout the growth in the lateral (c-axis) direction. The crystallite size in the thickness direction is always comparable to the film thickness, while the size in the c-axis direction shows no change.
7525
Mitsuru Ohtsuka, Takao Kusaka, Masato Yamanobe and Shinichi Kawate
Metal-insulator-metal emitters with an aluminum oxide insulating layer were investigated by making use of emission microscopy to observe the distribution and the fluctuation of electron emission. The microscope image showed a spotty pattern, indicating that the electrons were emitted from many separate sites on the surface. The density of spots reached 107 cm-2 under the driving voltage of 8.5 V. It was found that two types of emission sites having different power spectra of the fluctuation were randomly distributed on the surface. The different power spectra could be attributed to the formed and nonformed states of the emission sites.
7529
Retsuo Kawakami, Tomohisa Shimada, Yoshio Ueda and Masahiro Nishikawa
By using a simulation code for ion-solid interactions, EDDY, the dynamical behavior of W surfaces irradiated simultaneously with H+ and C+ impurity has been studied. This code models the fluence evolution of composition changes between C and W at the irradiated surface, which results from sputtering erosion and impurity deposition. The result has been described in terms of C impurity concentration in the irradiation. It has been compared with experimental data obtained by an ion beam irradiation device. In particular, the C impurity concentration has an important role in erosion/deposition at the W surface. As the C impurity concentration increases, the erosion is enhanced. As the C impurity concentration exceeds 3.00%, there is a transition from erosion to deposition which is due to the formation of a C film on the W surface. Regarding the result that the erosion changes to deposition, the simulation qualitatively reproduces the experimental results measured by X-ray photoemission spectroscopy (XPS). There is a different tendency in the fluence dependence for the different C impurity concentrations. For C:0.11%, the erosion rate increases with increasing fluence. This results from a growth of a local peak at around a depth of 20 nm in the depth profile of the deposited C. The growth is in good agreement with the experimental result, which shows that there is a strong contribution from recoil implantation of the deposited C due to a synergetic effect of the H and C impurity. For C:0.84%, there are almost the same tendencies as for C:0.11% in the erosion rate and in the depth profile. However, the growth of the local peak at around a depth of 10 nm is in disagreement with the measured one, which occurs near the surface. The disagreement appears to be attributable to the contribution of the surface segregation.
Nuclear Science, Plasmas, and Electric Discharges
7536
Kazuya Fujiwara, Tadayoshi Okuya, Michihiko Yanagisawa and Haruo Shindo
As a novel method of plasma production, microwave-sustained discharge was studied, particularly focusing on the permittivity effect on the axial distributions of the plasma in the discharge column with the two discharge tube materials. In the alumina discharge tube with a high permittivity, the axial distribution of electron density showed to be very localized in the upstream, nearby the microwave launcher, while in the quartz with a low permittivity a higher density region appeared further downstream. This difference in the axial distribution of the electron density could be explained by the behavior of the surface wave. It was stressed that this property could be one of the biggest advantages in its application to material processing on the industrial level, particularly in achieving a low-damage plasma process, such as low-damage silicon etching.
7541
Tae-Jung Chang, Yong-Ho Kim, Kwang-Suk Yoo and Yong-Seog Kim
Various types of barrier ribs for a plasma display panel were formed via a capillary molding process. A thermosetting paste was filled into cavities of working molds by means of capillary action and was cured prior to removal of the molds. The working molds were prepared by curing liquid polydimethylsiloxane on master molds that were produced from a photoresist. It was demonstrated that various types of barrier ribs could be produced successfully by sintering the ribs formed by the molding process. In addition, the effects of solid loading in the paste, prefiring temperature and type of barrier ribs on the morphologies of the ribs were investigated.
7547
Manabu Edamura, Ken Yoshioka, Ryoji Nishio, Saburo Kanai, Tadamitsu Kanekiyo, Seiichiro Kanno, Nobuyuki Mise, Akira Doi and Hideyuki Kazumi
A novel electro-magnetically coupled plasma (EMCP) etching tool for nonvolatile materials has been developed. The EMCP etcher is based on inductively coupled plasma generation and has a function for controlling surface reactions by supplying RF bias to a Faraday shield which covers a ceramic discharge dome. We investigated plasma controllability and chamber surface reaction controllability of the EMCP etcher and found that the RF-biased Faraday shield effectively keeps the internal surface of the dome clean in the etching processes of nonvolatile materials. Because of this feature, the EMCP etcher can be applied to the etching processes of various nonvolatile materials such as Pt, Ru, Ir, NiFe, Au, Mo, Ta, Al2O3, HfO2, ZrO2, and indium tin oxide (ITO).
7552
Yasunori Ohtsu, Kunihiro Yoshinaga and Hiroharu Fujita
The time-averaged energy distribution function of ions (TIIEDFs) impacted on an rf-biased substrate has been measured by means of a conventional retarding energy analyzer in electron cyclotron resonance microwave plasma. It was observed that TIIEDFs have a bimodal profile at a wide range of frequency fb biased at the substrate. It was revealed that the energy difference between bimodal peaks in TIIEDFs increased with increasing fpi/fb at fpi/fb<1, whereas it decreased with increasing fpi/fb at fpi/fb>1, where fpi is the ion plasma frequency.
7557
Akira Ejiri, Syun'ichi Shiraiwa, Yuichi Takase, Yoshihiko Nagashima, Hiroshi Kasahara, Takuma Yamada, Masayasu Ushigome, Daisuke Iijima, Yousuke Kobori, Tomoichirou Nishi et al
The four-beam correlation method has a potential of measuring fine-scale fluctuations locally. In the method, many lines of sight are measured and the coherences among them are calculated. As a proof of principle experiment, a visible fluctuation measurement system has been fabricated and applied to the TST-2 spherical tokamak plasma. Using this system, fluctuations were measured and high-frequency components (100±12.5 kHz) were analyzed. Because of a long parallel correlation length, local information was not obtained directly. However, comparison of the experimental results and those of a model calculation suggests that (i) the fluctuating emission is relatively localized in the peripheral region of the plasma, (ii) the perpendicular correlation length is of the order of 1 cm, while the parallel one is much longer than it and (iii) the magnetic field angle in the peripheral region agrees with that estimated from magnetic measurements.
Atoms, Molecules, and Chemical Physics
7564
Chih-Yi Pan, Jyh-Chiang Jiang and Dah-Shyang Tsai
The potential energy profiles in oxidizing tetraethyllead Pb(C2H5)4 are calculated at the B3LYP levels of density functional theory (DFT) to elucidate its reaction mechanism. There are a number of possible pathways to oxidize the organic lead radicals after the first step of cleaving one ethyl group from Pb(C2H5)4. Several pathways are calculated from the viewpoint of two basic types of reaction; the hydrogen scrambling from an ethyl group to an oxygen, and the oxygen insertion into a lead-carbon bond. A preference is predicted for those pathways involving the hydrogen scrambling reactions owing to their relatively lower reaction barriers. Among various reaction paths, the most important pathway is as follows: cleaving one ethyl from Pb(C2H5)4, binding with O2, undertaking two consecutive β-hydrogen migrations from the rest of the ethyls to the oxygens, and yielding one lead dihydroxide, two ethylenes, and one ethyl radical. The pathway is facile since the radical combines with O2 right after it forms and the following energy barriers are less than 25 kcal/mol. The major barrier is the first step of breaking Pb-C2H5, 54 kcal/mol. Other pathways involving oxygen insertion reactions are also calculated and compared, they are found to be less important energetically.
7570
Youngmin Choi, Hyunju Chang, Beyong-Hwan Ryu, Kijeong Kong, Jae Do Lee and Kwangsoo No
The electronic structure of chromium aluminum oxynitride has been investigated using resonant photoemission spectroscopy (RPES) and the discrete variational (DV)-Xα method. The RPES measurement of the electronic structure around the Cr 2p3/2 absorption edges exhibited significant resonant interference behavior for Cr 3d valence electrons, whereas it exhibited small resonant interference behavior for N 2p valence electrons. Therefore this RPES method can be useful for analyzing the valence band of chromium aluminum oxynitride film. The top of the valence band predominantly consists of Cr 3d and a small amount of N 2p. The difference between the measured photoemission spectra of the valence band and the DV-Xα calculation of chromium aluminum oxynitride ranges from 0.47 to 3.62 eV. This difference is probaly caused by the Coulomb interactions between the d electrons of chromium and the structure of the amorphous film. Through the experimental and theoretical studies, the valence band structure of chromium aluminum oxynitride came to be understand in detail.
7574
Jong-Shinn Wu and Yu-Lin Hsu
A practical procedure for deriving parameters of the variable soft sphere (VSS) molecular model for the Lennard–Jones potential of gas species in the direct-simulation Monte Carlo (DSMC) method is introduced. Intermolecular potential energy is fitted through the Lennard–Jones (L–J) potential, which is obtained by quantum chemistry computation. Computed L–J potentials are then used to compute viscosity and diffusivity coefficients for like and unlike molecules, respectively, based on gas kinetics theory. Related parameters of the VSS molecular model are derived by fitting these computed coefficients to those derived from the VSS model. Test results for O2–H2 mixtures using this procedure are in good agreement with existing data. VSS parameters for silicon-based species frequently encountered in the chemical vapor deposition process are derived as an example to illustrate the importance of this procedure in extending the applicability of the DSMC computation to gas species other than air-related species.
Instrumentation, Measurement, and Fabrication Technology
7576
Yoon-Hyeok Kwon, Seung Hwangbo, June-Ho Lee, Dong-Young Yi and Min-Koo Han
The space charge distributions in solid dielectrics have been usually investigated by means of the pulsed electroacoustic (PEA) method. However, most previous studies have been limited to the phenomenological analysis under DC voltages. In our study, the space charge distribution in cross-linked polyethylene (XLPE) has been measured using AC voltages by means of the modified PEA method. Simultaneously, the streamer discharges in an air gap have been measured in order to investigate the relationship between space charge and discharge current, and the relationship has been adapted to the case of dielectric barrier discharge. At high AC voltages, discharge current increases to the critical point, but no further increase is exhibited over the critical voltage and the discharge pattern is resolved by the space charge. This result indicates that the frequency effect and space charge characteristics of dielectric materials are preferred to the voltage effect in the adaptation to dielectric barrier discharge. The results well explain the space charge effect on partial discharge and the dielectric barrier discharge phenomenon.
7580
Takuya Bungo, Yuzuru Mizuhara, Takaharu Nagatomi and Yoshizo Takai
An atomic mixing, surface roughness and information depth (MRI) model was extended to describe Auger electron spectroscopy (AES) sputter-depth profiles measured using a cylindrical mirror analyzer (CMA) tilted at oblique angle. The extension was performed by taking into account the effects of the dependence of the information depth of detected Auger electrons on the azimuthal angle of the entrance of the CMA. Al-LVV and Al-KLL depth profiles of a GaAs/AlAs superlattice material were analyzed using the extended MRI model. The present results revealed that the depth profiles calculated by the extended MRI model can be fitted to the experimental ones measured using the tilted CMA under the condition that the thickness of the mixing layer is smaller than the information depth. In contrast, the depth profiles calculated by the conventional MRI model can not trace the experimental ones. The present study confirmed that the extended MRI model is well worthy of application to the analysis of the AES depth profiles obtained using the tilted CMA with low-energy ions of less than a couple of hundreds eV, which is expected to reduce the thickness of the damaged layer.
7585
Young-Do Joo, Ashok Kumar Sinha and Gun-Sik Park
In the fabrication of the practical helix slow wave structure (SWS), the misalignment or the dielectric constant variation in its support is not avoidable and, thus, causing azimuthal asymmetry in the structure. Therefore, the analysis of the asymmetric structure becomes an important issue. In this study, rigorous field analysis of a general asymmetric helical SWS was done by considering the structure as a helix supported by n wedge shaped dielectric supports, enclosed in a metal envelope. To consider the angular harmonic effect, the dielectric was not smoothed out. Using the present theory, the dispersion characteristics of the asymmetric helical structure were obtained. The study of the dispersion characteristics of the asymmetric structure revealed the stopband characteristics near the π-phase-shift point. This result was compared with that obtained from 3D FEM code, high frequency structure simulator (HFSS) and found to be in good agreement. It was also found that the asymmetry in the structure lowered the phase velocity and the cut-off frequency but increased the stopband width.
7594
Yasushi Yamada, Katsuji Yamashita, Yumi Masuoka and Masami Ogita
Thick film NO2 sensors comprised of various Zn–Sn–Sb–O composite materials have been studied. The gas-sensing materials were prepared by sintering a mixture of ZnO, SnO2 and Sb2O3 powders at 800, 1000 and 1200°C. Thick films were fabricated on an Al2O3 substrate using a conventional screen-printing method. The atomic ratios of the fabricated films were confirmed by the results obtained from EPMA (Electron probe micro analysis). The dominant compositions of the sintered gas-sensing materials were characterized by XRD (X-ray diffraction). It was found that the composition of the gas-sensing material depended on the initial Sb/Zn atomic ratio, where the gas-sensing material shows almost single-phase ZnSb2O6 when Sb/Zn = 2.0, a mixture of ZnSb2O6 and SnO2 when Sb/Zn = 1.0 and a mixture of SnO2 and an unknown crystal when Sb/Zn = 0.5. The sensing film shows high sensitivity and excellent selectivity for ppm levels of NO2 gas because the film shows no sensitivity for i-C4H10 and CO gases. The capability for NO2 detection in a practical application was examined by using the sensor to monitor the gas which was emitted from a kerosene heater.
7599
Tomohiro Ezure, Koichi Mizutani and Hiroyuki Masuyama
An optical method for measurement of sound fields using the Mach–Zehnder interferometer is described. In this study, we investigate the influence of diffracted light that passes through sound fields generated by radio frequency for measurement using the interferometer. The intensities of the diffracted light and the interference light are measured by a charge-coupled device (CCD). To compare the values acquired from the numerical estimation with those acquired from the measurement, we confirm the validity of the numerical estimation equation.
7601
Motohiro Kohno, Toshikazu Kitajima, Sadao Hirae and Shin Yokoyama
We investigated the charge generation effect on a silicon oxide surface treated with hydrofluoric acid by noncontact capacitance measurement. A negative charge is induced by storing wafers in a plastic box and it increases over time, while N2-purged box storage induces a negligible negative charge. UV irradiation also induces a negative charge, however, the sum of both charges is almost constant irrespective of the storage time and environment. These phenomena were explained in terms of surface contamination.
General Physics
7603
Hsien-Keng Chen, Tsung-Nan Lin and Juhn-Horng Chen
The synchronization of chaos of the two identical chaotic motions of the Japanese attractor has been studied. First, the stability of the chaos synchronization of the systems is investigated by Liapunov's direct method. Some sufficient conditions of global asymptotic synchronization are attained from rigorous mathematical theory. It has also been demonstrated numerically that applying two different kinds of one-way coupling technology can synchronize the two identical chaotic systems. The sign of the sub-Liapunov exponent has been used as an indicator for the occurrence of chaos synchronization. Chaos synchronization can be assured as shown well by phase trajectory. In addition, the chaotic signals are used to mask the message function in the secure communication system.
Applied Bioscience
7611
Ayako Sumi, Norio Ohtomo, Yukio Tanaka, Sadashi Sawamura, Lars Folke Olsen and Nobumichi Kobayashi
A newly devised procedure of prediction analysis, which is a linearized version of the nonlinear least squares method combined with the maximum entropy spectral analysis method, was proposed. This method was applied to time series data of measles case notification in several communities in the UK, USA and Denmark. The dominant spectral lines observed in each power spectral density (PSD) can be safely assigned as fundamental periods. The optimum least squares fitting (LSF) curve calculated using these fundamental periods can essentially reproduce the underlying variation of the measles data. An extension of the LSF curve can be used to predict measles case notification quantitatively. Some discussions including a predictability of chaotic time series are presented.
7621
David C. Ng, Keiichi Isakari, Akihiro Uehara, Keiichiro Kagawa, Takashi Tokuda, Jun Ohta and Masahiro Nunoshita
In this work, we study the effect of bending on the pulse-frequency-modulation (PFM)-based photosensor. Based on the results of our study of strain on metal oxide semiconductor field-effect transistor (MOSFET) devices, we explain the behavior of the photosensor under compressive and tensile bending. We found that the maximum frequency variation to bending is about +4% when extrapolated to the curvature of the human eye. From this study we hope to minimize or eliminate the effect of bending on LSI circuits. Although this study specifically deals with the PFM photosensor circuit, any other LSI circuit subjected to strain can be treated similarly.
7625
Tomoyuki Ohya, Noriko Oikawa, Ryuzou Kawabata, Hirotaka Okabe and Shoichi Kai
In order to evaluate the physiological damage to plants caused by osmotic stress, we have investigated the relationship between the inhibition of root elongation and spontaneous photon emission from the root. Adzuki bean roots were soaked in polyethylene glycol (PEG) solutions for short periods in their early growth stage, and their root length and photon emission were measured afterwards. Consequently, it became clear that the root elongation decreased with the increase of PEG concentration. Moreover, there was a clear correlation between the emission intensity of the cell division area in the root and the inhibition of elongation, though the elongation of individual roots varied to some degree.
Nano Science and Technologies
7629
Yeji Kim, Nobutsugu Minami, Weihong Zhu, Said Kazaoui, Reiko Azumi and Mutsuyoshi Matsumoto
The Langmuir–Blodgett technique has been applied to build optically homogeneous thin films of chemically solubilized single-wall carbon nanotubes (s-SWNTs) which possess good surface spreading properties at the air/water interface. Deposition can be performed in a layer-by-layer fashion up to 100 or more layers either by horizontal lifting or vertical dipping, allowing to readily control the film thickness. Their visible to near-infrared absorption spectra showing the characteristic features of semiconducting and metallic SWNTs prove the intactness of their one-dimensional electronic states during the preparation process. Polarized absorption spectroscopy and atomic force microscope (AFM) observation demonstrate that the tubes are oriented in the direction of the trough barrier (horizontal lifting) or in the dipping direction (vertical dipping). These are attributed to compression-induced or flow-induced orientation, respectively, the latter found to be much stronger than the former. The realization of homogeneous thin films of SWNTs with a controllable thickness and tube orientation should be an important basis for the future development of their scientific understanding and technological applications.
7635
JunHo Kim, Jeongyong Kim, K.-B. Song, S.-Q. Lee, E.-K. Kim and K.-H. Park
We investigate light transmission of Ag nano protrusions with a scanning near-field optical microscope (SNOM) to study the surface plasmon (SP) in metallic films. A Ag nanoprotrusion whose height is ∼20 nm is fabricated by the deposition of Ag on the Ti nano-protrusion template which is made by nano-oxidation with an atomic force microscope (AFM). It is found that through several scans, the tip is coated with Ag from the sample, and this modified tip shows apparent undulation patterns in SNOM imaging, while a fresh tip does not. The undulation pattern in the SNOM image is observed only along the direction of polarization light close to the expected undulation period. This result indicates that local launching of SP is effective with an Ag-coated tip and the SP launching characteristic is consistent with the so-called cos 2Φ SP distribution. By finite domain time difference (FDTD) simulations, it is confirmed that light transmission is enhanced in the Ag-coated tip compared to the fresh tip. Our results imply that local illumination with a noble-metal-coated cantilever probe tip is desirable for obtaining more detailed features in SNOM images involved with SP. Our results also indicate that a nano protrusion fabricated by AFM-based nano-oxidation can be applied to an optical element using surface plasmon.
7640
Yasuro Niidome, Hironobu Takahashi, Takahiro Kawasawa, Ayako Hori and Sunao Yamada
The technique of laser-induced deposition has been applied to the spatioselective deposition of gold nanoparticles onto a membrane filter and the inner wall of a glass capillary tube. The deposited gold nanoparticles acted as seeds for electroless copper plating of the gold deposited region. Microscopic and scanning electron microscopic measurements verified the successful plating of only the region of deposited gold nanoparticles.