RAPID COMMUNICATIONS
092001
The following article is Free article
Sung Hun Wee, Amit Goyal, Yuri L Zuev and Claudia Cantoni
High temperature superconducting (HTS) wires capable of carrying large critical currents
with low dissipation levels in high applied magnetic fields are needed for a wide range
of applications. In particular, for electric power applications involving rotating
machinery, such as large-scale motors and generators, a high critical current,
Ic, and a high engineering critical current density,
JE, in applied magnetic fields in the range of 3–5 Tesla (T) at 65 K are required. In
addition, exceeding the minimum performance requirements needed for these
applications results in a lower fabrication cost, which is regarded as crucial to realize or
enable many large-scale bulk applications of HTS materials. Here we report the
fabrication of short segments of a potential superconducting wire comprised of a
4 µm
thick YBa2Cu3O7−δ
(YBCO) layer on a biaxially textured substrate with a 50% higher
Ic and
JE than
the highest values reported previously. The YBCO film contained columns of self-assembled nanodots of
BaZrO3 (BZO) roughly
oriented along the c-axis of YBCO. Although the YBCO film was grown at a high deposition rate, three-dimensional
self-assembly of the insulating BZO nanodots still occurred. For all magnetic field orientations, minimum
Ic and
JE at 65 K, 3 T for
the wire were 353 A cm−1
and 65.4 kA cm−2, respectively.
092002
Michela Fratini, Rocchina Caivano, Alessandro Puri, Alessandro Ricci, Zhi-An Ren, Xiao-Li Dong, Jie Yang, Wei Lu, Zhong-Xian Zhao, Luisa Barba et al
We report the temperature dependent x-ray powder diffraction of the quaternary
compound NdOFeAs (also called NdFeAsO) in the range between 300 and 95 K. We
have detected the structural phase transition from the tetragonal phase, with
P4/nmm
space group, to the orthorhombic or monoclinic phase, with
Cmma or
P 112/n (or
P 2/c) space group, over a broad temperature range from 150 to 120 K, centered at
T0∼137 K. Therefore the temperature of this structural phase transition is strongly reduced, by about
∼30 K, by increasing the internal chemical pressure going from LaOFeAs to NdOFeAs. In contrast,
the superconducting critical temperature increases from 27 to 51 K going from LaOFeAs to
NdOFeAs doped samples. This result shows that the normal striped orthorhombic
Cmma
phase competes with the superconducting tetragonal phase. Therefore by controlling the internal
chemical pressure in new materials it should be possible to push toward zero the critical temperature
T0
of the structural phase transition, giving the striped phase, in order to get superconductors with
higher Tc.
092003
K A Yates, L F Cohen, Zhi-An Ren, Jie Yang, Wei Lu, Xiao-Li Dong and Zhong-Xian Zhao
The newly discovered oxypnictide family of superconductors show very high critical
temperatures of up to 55 K. Whilst there is growing evidence that suggests a nodal order
parameter, point contact Andreev reflection spectroscopy can provide crucial information such
as the gap value and possibly the number of energy gaps involved. For the oxygen deficient
NdFeAsO0.85 with
a Tc
of 45.5 K, we show that there is clearly a gap value at 4.2 K that is of the
order of 7 meV, consistent with previous studies on oxypnictides with lower
Tc. In addition, taking the spectra as a function of gold tip contact pressure reveals important
changes in the spectra which may be indicative of more complex physics underlying this
structure.
092004
J D Moore, K Morrison, K A Yates, A D Caplin, Y Yeshurun, L F Cohen, J M Perkins, C M McGilvery, D W McComb, Z A Ren et al
Here we report the use of global and local magnetometry and Hall probe imaging to
investigate the electromagnetic connectivity of the superconducting current path in the
oxygen-deficient fluorine-free Nd-based oxypnictides. High resolution transmission electron
microscopy and scanning electron microscopy show strongly layered crystallites, evidence for a
∼5 nm amorphous oxide around individual particles, and second phase neodymium oxide
which may contribute to the large paramagnetic background at high field and at high
temperatures. From global magnetometry and electrical transport measurements it is clear
that there is a small supercurrent flowing on macroscopic sample dimensions (mm), with a
lower bound for the average (over this length scale) critical current density of the order of
103 A cm−2. From
magnetometry of powder samples and local Hall probe imaging of a single large conglomerate particle
∼120 µm it is
clear that, on smaller scales, there is better current connectivity with a critical current density of the
order of 5 × 104 A cm−2. We find enhanced flux creep around the second peak anomaly in
the magnetization curve and an irreversibility line significantly below
Hc2(T)
as determined by ac calorimetry.
TOPICAL REVIEW
093001
Piotr W Klamut
The ruthenocuprates are high temperature superconductors, which have raised a substantial
interest due to the simultaneous presence of the transition metal magnetism and superconductivity.
The compounds represent a complex and experimentally challenging research arena, with
interesting recent experimental developments. The author reviews some key properties of
RuSr2RECu2O8,
RuSr2RE2−xCexCu2O10−y, and of a few derivative compounds of the ruthenocuprate family.
PAPERS
095001
Naoyuki Amemiya and Ken Akachi
Numerical electromagnetic field analyses of high
Tc
superconducting tape in coils were carried out to calculate the magnetic field generated by
the shielding (magnetization) current in superconducting tape. The numerical
model employs the power law electric field–current density characteristic and
the thin strip approximation, in which the current component normal to the
wide face of the tape is neglected. The shielding (magnetization) currents lead to
non-uniform current distributions in the superconducting tape in the coils. The
magnetic field generated by the shielding (magnetization) current can deteriorate the
field quality and could be a concern in insert coils for NMR magnets using high
Tc
superconducting tape.
095002
D D Shivagan, P M Shirage, A Crisan, Y Tanaka, A Iyo, Y Kodama, K Tokiwa, T Watanabe, N Terada and N Hamada
We have measured the vortex melting lines of high-pressure-synthesized
Ba2Ca3Cu4O8(O1−yFy)2 (nominal
composition, 2y = 1.3, 1.6
and 2.0) F(2y)-0234
multilayered high-Tc
superconductor using fundamental and third harmonic susceptibility responses
carried out on preferentially oriented crystallites with very low ac field amplitude
(5 µT) and in applied dc fields up to 6 T. The vortex melting lines of all three F-substituted
samples show interesting doping dependence and are very well described by the commonly
accepted theory of melting lines. Interestingly, we discovered that the models describing the
temperature dependence of the in-plane London penetration depth also depend
on the doping level: the 3D XY model for the nearly-optimum-doped sample
[F(1.3)], the mean-field theory for the under-doped sample [F(1.6)] and the two-fluid
model for the heavily-under-doped sample [F(2.0)]. We found that the vortex
melting lines in F-0234 are determined by the interplay in the coupling of pancake
vortices through the charge reservoir layer (CRL), and through the block of inner
CuO2
planes (IPs), respectively. The anisotropy values (47 for the near-optimally-doped sample)
derived from experimental vortex melting lines are consistent with the values obtained by
first-principles electronic-band-structure calculations.
095003
Rodney Marcelo do Nascimento, Carlos Roberto Grandini and Alfredo Gonçalves Cunha
The compound SmBa2Cu3O7−δ
(SBCO)—obtained by substituting rare-earth Sm for Y in the well-known and most studied
YBa2Cu3O6+δ
(YBCO)—is potentially attractive to study in order to understand the superconductivity
mechanism in physics and in electronic device applications. For SBCO, the
possibility of variable stoichiometry and the high mobility of oxygen in
CuOx
planes give rise to a rich phase diagram. This study reports on the effect of heat treatments
in an oxygen atmosphere on the anelastic properties of this oxide, in which relaxation
processes were observed, attributed to oxygen atom jumps present in the Cu–O planes
during the orthorhombic phase.
095004
Fazhu Ding, Hongwei Gu and Tao Li
Dense and homogeneous superconductive
YBa2Cu3O7−x
(YBCO) thin films were grown epitaxially on single-crystal
LaAlO3
(LAO) substrates by a new MOD method with terpineol-modified trifluoroacetic solution. The
YBCO precursor solution incorporated with terpineol enabled a remarkable decrease in the
organic pyrolysis process. The YBCO films have an onset critical temperature of 90 K and
Jc (77 K,
0 T) of 3.8 MA cm−2. The addition of terpineol was suggested to be responsible for the smoother and
low-stressed YBCO films.
095005
Y Q Zhang, X Q Xiang, J F Ding and X G Li
In this paper we report the transport properties of
c-axis-oriented
superconducting La1.44Nd0.4Sr0.16CuO4
films on LaSrAlO4
substrates with different thicknesses in various magnetic fields parallel and perpendicular to the
c
axis of the films. It is found that with decreasing film thickness there is a
crossover from the parallel shift to fan-shape broadening in the resistive
transitions. Moreover, for both field configurations, the flux pinning potential
U0(H)
of the film shifts upward with an order of magnitude with increasing in-plane compressive
strain. These results indicate that the compressive epitaxial strain and strain-induced
destabilization of the static charge stripes are important aspects for the promotion of
superconducting transition temperature as well as the flux pinning potential.
095006
M Mazaheri, S Mofakham and M Akhavan
We have investigated the substitution of Ce and divalent Ca with a radius similar to Gd in
Gd1−x−zCexCazBa2Cu3O7−δ. We have
prepared Gd1−x−zCexCazBa2Cu3O7−δ
compounds with different concentrations of Ce and Ca by the standard solid-state
reaction technique. X-ray diffraction (XRD) experiments are performed and the
results are refined by the Rietveld method. XRD analysis shows a predominantly
single-phase perovskite structure with orthorhombic Pmmm symmetry. In
Gd1−x−zCexCazBa2Cu3O7−δ compounds, induced
suppression of Tc
due to Ce doping is compensated by hole doping with increasing Ca substitution for Gd. With the increase of
Ca content, Tc
increases up to an optimum value; thereafter it begins to decrease, and the resistivity
curve has a bell shape. The transition temperature width also decreases for all
x with the
increase of z. In order to interpret the normal state electrical properties of the samples, the quantum
percolation theory based on localized states is applied. Fitting the data with
two-dimensional variable range hopping and three-dimensional variable range hopping
models, and a Coulomb gap regime, shows that our results are consistent with the
Coulomb gap regime. The results of the electrical and structural properties of
Gd1−x−zCexCazBa2Cu3O7−δ-doped compounds suggest that Ca doping compensates the suppression of the
superconducting state caused by the Ce content.
095007
Kazuhide Tanaka, Kazuo Funaki, Takahiro Sueyoshi, Yushi Sasashige, Kazuhiro Kajikawa, Masataka Iwakuma, Michiya Okada, Hiroaki Kumakura and Hidemi Hayashi
We designed and fabricated two types of composite wires with 6
MgB2
filaments. One is a Cu-sheathed Nb-barrier wire and the other is a CuNi-sheathed
Ta-barrier wire. The transverse-field losses of the trial wires were measured with a
standardized pickup coil system in liquid helium. We evaluated the observed AC losses
using two structural models, a multifilament conductor model and a hollow-cylindrical one.
For the CuNi-sheathed Ta-barrier wire, the AC loss property can be explained by
the usual model of multifilament conductors. Further reductions in AC loss can
be expected by making the filaments thinner. For the Cu-sheathed Nb-barrier
wire, theoretical considerations suggest the multifilament structure behaves as a
hollow-cylindrical superconductor in the AC loss property. Thus, we need to pay
particular attention to designing the barrier material for reduction in the AC
loss.
095008
A Yamamoto, A A Polyanskii, J Jiang, F Kametani, C Tarantini, F Hunte, J Jaroszynski, E E Hellstrom, P J Lee, A Gurevich et al
Early studies have found quasi-reversible magnetization curves in polycrystalline
bulk rare-earth iron oxypnictides that suggest either widely spread obstacles to
intergranular current or very weak vortex pinning. In the present study of polycrystalline
samarium and neodymium iron oxypnictide samples made by high pressure synthesis,
the hysteretic magnetization is significantly enhanced. Magneto-optical imaging
and study of the field dependence of the remanent magnetization as a function
of particle size both show that global currents over the whole sample do exist
but that the intergranular and intragranular current densities have distinctively
different temperature dependences and differ in magnitude by about 1000. If
the highest current density loops lie only within grains, their magnitude is
∼5 × 106 A cm−2
at 5 K and self-field. Whole sample current densities, though two orders of magnitude lower at
1000–10 000 A cm−2, are some two orders of magnitude higher than in random polycrystalline cuprates. We
cannot yet be certain whether this large difference in global and intragrain current density
is intrinsic to the oxypnictides or due to extrinsic barriers to current flow, because the
samples contain a significant second phase, some of which wets the grain boundaries and
may cause a superconducting–normal–superconducting proximity effect in the whole
sample critical current.
095009
Hisashi Shimakage, Masahiro Tatsumi and Zhen Wang
Ultrathin MgB2
films were fabricated by using a co-evaporation method. We increased the Mg evaporation rate up to
32 nm s−1
by adjusting the chamber configuration and succeeded in fabricating
MgB2
thin films with high quality at a high substrate temperature of
350 °C. The thickness dependence of the thin film characteristics showed that an ultrathin film with a
thickness of 4.2 nm had superconducting properties with a critical temperature of 8 K and a resistivity
of 1200 µΩ cm
at 40 K. The mean roughness of a 15 nm thick
MgB2
thin film was 0.18 nm, which indicated that our
MgB2
thin films have the potential to fabricate sub-micron size patterns.
095010
Zhi Wen Gao and You He Zhou
We use numerically evaluated contour integrals and crack length versus time analysis to
simulate crack propagation based on electromagnetic forces for superconducting
trapped-field magnets. The coupling finite element and infinite element method has been
employed in the numerical analysis. In this paper an interior elliptical crack is
allowed to grow based on the critical stress criterion. Stress intensity factors and
J
integrals are estimated during field descent. Crack propagation is modeled by the change of
crack length with time, and contours of the Mises equivalent stress at the final stage of the
crack propagation are shown.
095011
M R Osorio, J A Lorenzo Fernández, J A Veira and F Vidal
We have suggested recently that the introduction of artificial weak zones (AWZ) in the
superconducting elements used in fault current limiters (FCL) could greatly improve the
recovery time after a quench provoked by the FCL activation. In this work, a finite element
method (FEM), based on the thermal and electrical equations describing the behaviour of
samples when the normal–superconducting transition occurs, is used to study the
thermal evolution during the whole quenching–recovery process of high temperature
superconducting rings with grooves, which act as AWZ. Our simulations allow us to set the
size of grooves and the more suitable material properties to obtain a better sample
refrigeration.
095012
J Beyer and D Drung
Superconducting quantum interference device (SQUID) sensors are used to sense changes in
various physical quantities, which can be transformed into changes in the magnetic flux
threading the SQUID loop. We have developed a novel SQUID array dc current sensor. The
device is based on a series array of identical dc SQUIDs. An input signal current to be
measured is coupled tightly but non-uniformly to the SQUID array elements. The input
signal coupling to the individual array elements is chosen such that a single-valued,
non-periodic overall voltage response is obtained. Flux offsets in the individual SQUIDs
which would compromise the sensor voltage response are avoided or can be compensated.
We present simulations and experimental results on the SQUID Array for Dc
(SQUAD) current sensor current sensor performance. A dc current resolution of
<1 nA in a measurement bandwidth of 0–25 Hz is achieved for an input inductance of
LIn<3 nH.
095013
M R Osorio, A Bétrancourt, M X François, J A Veira and F Vidal
In this work we probe a compact superconducting fault current limiter (SFCL) integrated in the cold
heat exchanger of a thermoacoustic refrigerator. A design for an SFCL device with a power of about
2.2 kW is presented and described in detail. A thermoacoustic refrigerator is
also proposed which, under fault conditions, must be able to remove around
50 W
at 80 K. A simulation routine is run to test the performance of the SFCL, based on YBCO films,
in terms of both the limiting capacity and the energy to be dissipated and removed inside
the heat exchanger.
095014
A O Tchikilev and L M Tkachenko
A model of geometry for the coil block in the end parts of superconducting multi-layer
magnets has been considered to take into account finite dimensions of the Rutherford-type
cable. A method for optimization of coil lengths for superconducting magnets is introduced.
The length of the end parts is shortened, which gives a larger effective length of
the magnet and simplifies the assembly technique. Numerical results of coil end
optimization for the dipole superconducting magnet are shown, which have been
designed with the help of a program for modeling of coil blocks in the end parts.
095015
Ke Chen, Menno Veldhorst, Che-Hui Lee, Daniel R Lamborn, Raymond DeFrain, Joan M Redwing, Qi Li and X X Xi
A hybrid physical–chemical vapour deposition (HPCVD) system consisting of
separately controlled Mg-source heater and substrate heater is used to grow
MgB2
thin films and thick films at various temperatures. We are able to grow superconducting
MgB2 thin films at
temperatures as low as 350 °C
with a Tc0 of 35.5 K.
MgB2 films up to
4 µm in thickness
grown at 550 °C
have Jc
over 106 A cm−2
at 5 K and zero applied field. The low deposition temperature of
MgB2 films is desirable
for all-MgB2 tunnel
junctions and MgB2
thick films are important for applications in coated conductors.
095016
Hossein Heydari, Faramarz Faghihi, Reza Sharifi and Amir Hossein Poursoltanmohammadi
Current injection transformer (CIT) systems are within the major group of the
standard type test of high current equipment in the electrical industry, so their
performance becomes very important. When designing high current systems, there
are many factors to be considered from which their overcurrent protection must
be ensured. The output of a CIT is wholly dependent on the impedance of the
equipment under test (EUT). Therefore current flow beyond the allowable limit can
occur. The present state of the art provides an important guide to developing
current limiters not only for the grid application but also in industrial equipment.
This paper reports the state of the art in the technology available that could be developed
into an application of superconductivity for high current equipment (CIT) protection with
no test disruption. This will result in a greater market choice and lower costs for equipment
protection solutions, reduced costs and improved system reliability. The paper will
also push the state of the art by using two distinctive circuits, closed-core and
open-core, for overcurrent protection of a 25 kA CIT system, based on a flux-lock-type
superconducting fault current limiter (SFCL) and magnetic properties of high
temperature superconducting (HTS) elements. An appropriate location of the HTS
element will enhance the rate of limitation with the help of the magnetic field
generated by the CIT output busbars. The calculation of the HTS parameters for
overcurrent limiting is also performed to suit the required current levels of the CIT.
095017
A Martinelli, M Ferretti, P Manfrinetti, A Palenzona, M Tropeano, M R Cimberle, C Ferdeghini, R Valle, C Bernini, M Putti et al
SmFeAsO and the isostructural superconducting
SmFeAs(O0.93F0.07)
phase were prepared and characterized by means of Rietveld refinement of x-ray
powder diffraction data, scanning electron microscope observation, transmission
electron microscope analysis, and resistivity and magnetization measurements.
Sintering treatment strongly improves the grain connectivity, but, on the other hand,
induces a competition between the thermodynamic stability of the oxy-pnictide and
Sm2O3, thus
affecting the sample purity. In the pristine sample both magnetization and resistivity measurements
clearly indicate that two different sources of magnetism are present: the former related to Fe ordering
at T∼140 K and the latter due to the Sm ions that order antiferromagnetically at low temperature.
The feature at 140 K disappears in the F-substituted sample, and a superconducting
transition appears, at low temperatures. The magnetoresistivity curves of the F-substituted
sample probably indicate very high critical field values.
095018
H Fujii, K Togano and K Ozawa
We have studied grain coupling and critical current density
(Jc) in ex situ processed
Fe-sheathed MgB2−xCx
(x = 0, 0.05
and 0.10) tapes fabricated by a powder-in-tube (PIT) technique. Compared with commercially available
MgB2 powder, homemade
powders of MgB2−xCx
contained larger amounts of MgO. Therefore, tapes using these homemade powders showed much lower
Jc values.
Chemical treatment of the homemade powders in acid solutions brought about a large enhancement
in Jc
of tapes, mainly due to the dissolution of MgO. The transport
Jc values
of tapes were almost the same at 4.2 K and 10 T for both powders with chemical treatment, independent of
x, although tapes
using powders with x≥0.05
showed a large enhancement in normalized volume pinning force
(Fp) in the high-field region and small field dependence in
Jc due
to carbon substitution. This can be attributed to high temperature heat treatment for ex situ processed
MgB2 tapes. At sintering,
MgB2−xCx probably partially
decomposes into MgB2, MgB4
and C, producing precipitates at grain boundaries. This brings about weak
coupling of grains and hence negligible enhancement in the low-field region in
Jc of tapes
with x≥0.05.
095019
L M Volkova
Simulation of ‘hybrid’ superconductors of 3d, 4d and 5d transition elements consisting of
two different superconducting fragments located between positively charged ions
planes—B′O2 oxide
planes and B2C2
intermetallic layers—has been performed on the basis of the structure of
Sr2Mn3As2O2
(A2(B2C2)(B′O2)). The oxide planes
are similar to those of CuO2
in high-temperature superconducting cuprates while the intermetallic layers are similar to those of
Ni2B2
in low-temperature superconducting borocarbides
RNi2B2C
and Fe2As2
layers in high-temperature superconducting oxypnictides
RFeAsO1−xFx.