RAPID COMMUNICATION
122001
E Backen, S Haindl, T Niemeier, R Hühne, T Freudenberg, J Werner, G Behr, L Schultz and B Holzapfel
LaFeAsO1−xFx
thin films were deposited successfully on (001)-oriented
LaAlO3 and MgO substrates
from stoichiometric LaFeAsO1−xFx
polycrystalline targets with fluorine concentrations up to
x = 0.25
by pulsed laser deposition (PLD). Room temperature deposition
and post annealing of the films yield films with a pronounced
c-axis texture and a strong biaxial in-plane orientation. Transport measurements
show metallic resistance and the onset of superconductivity at 11 K.
μ0Hc 2(T)
was determined by resistive measurements and yield
μ0Hc 2
values of 3 T at 3.6 K for
and 6 T at 6.4 K for
.
PAPERS
125001
G L Sun, Y T Song and C T Lin
The growth of YBa2Cu4O8
single crystals was performed using KOH flux under ambient pressure. By testing five sorts of crucible
material, ZrO2
and Al2O3
are found to be suitable for the growth. A stepwise-cooling method was applied to increase
the size of the crystals. The as-grown crystals could be separated from the residual flux by
methanol solvent. The crystals showed a plate-like morphology with dimensions
1.2 × 0.5 × 0.3 mm3. Study of the structure in the (001) plane indicated that the formation of the crystal occurred
by a two-dimensional nucleation or spiral growth mechanism, depending on the supersaturation
of the solution. Defects in the crystals were revealed by etching, which exhibited an
interesting feature of etch pits with an orthorhombic structure consisting of {001}, {100} and
{010} faces. The superconducting property of the crystals shows very sharp transition at a
Tc
of 82.9 K.
125002
E Bartolomé, B Bozzo, X Granados, F Sandiumenge, T Puig and X Obradors
Magnetic Hall probe microscopy in combination with an inverse problem solver was used to
simultaneously determine the intragranular and intergranular critical current density dependences
on the applied field of YBCO melt-textured welds with [001]-misorientation angles from
0° to
30°. This methodology enabled us to investigate the pinning mechanisms of grain boundary
vortices, which evolve from Abrikosov vortices (AVs) to Abrikosov–Josephson vortices
(AJVs) and then to Josephson vortices (JVs) as the angle increases. We present a magnetic
field versus grain boundary angle phase diagram at 77 K in which different intergrain vortex
motion regimes can be identified.
125003
P Kováč, I Hušek and T Melišek
Stabilized seven-core MgB2
cable has been made from two-axially rolled single-core wires with a Ti/Cu
sheath. It was shown that drawing deformation applied prior to braiding
influences the core density and consequently also the transport current density,
Jc. A proper drawing deformation allows avoiding
Jc
degradation, and cable critical current density
104 A cm−2 at 9.5 T
and 105 A cm−2 at 4.5 T can be reached at 4.2 K.
125004
D-J Jang, H-S Lee, B Kang, H-G Lee, M-H Cho and S-I Lee
We have studied the angle-dependent motion of the anisotropic flux line lattice (FLL) and the peak effect (PE) in
MgB2 single crystals. For
arbitrary angles (θ), we
measured the resistance (R(H)) and critical current (Ic(H)) with AC and DC currents, respectively. At low fields below the PE,
R(H)
and Ic(H)
showed a weak angular dependence, regardless of the type of excitation
current, because of the stable vortex state. At intermediate fields near the PE,
R(H) and
Ic(H) at the onset of the
PE varied with θ, depending on the type of external current, due to the metastability of the disordered
vortex lattice near the PE. At high fields above the PE and near the upper critical field
Hc2,
the R(H)
curves showed a simple scaling behavior with
θ.
125005
M Zouaoui, A Ghattas, M Annabi, F Ben Azzouz and M Ben Salem
We investigated the microstructure and flux pinning capability of the bulk
(Bi,Pb)2Sr2Ca2Cu3Oy
system (denoted as (Bi, Pb)-2223) with 0.0–0.3 wt% nano-size
ZrO2
particles (10–20 nm) addition synthesized by solid state reaction. Phase analysis by
x-ray diffraction (XRD), granular structure examination by scanning electron
microscopy (SEM), microstructure investigation by transmission electron
microscopy (TEM) equipped with energy dispersive x-ray spectrometer
(EDS), critical current density dependence on the applied magnetic field
Jc(H) and electrical
resistivity ρ(T,H)
were carried out. The results show that activation energies of vortex flux motion
U(H), critical
current density Jc(H)
behavior in applied magnetic field and volume pinning force density
Fp are enhanced by the
addition of 0.1 wt% ZrO2. The pinning force analysis and microstructure observations indicated that the
improvement of flux pinning is suggested to originate from the introduction of extrinsic
pinning centers due to the formation of normal nano-sized Zr-rich phase.
125006
David M J Taylor, Maisoon Al-Jawad and Damian P Hampshire
Superconductivity provides the enabling technology for producing high-field magnets in
applications including medical body scanners and particle accelerators. The upper critical field
(BC2(0)) of the superconductor ultimately limits the field that the magnet can produce. The reports about
PbMo6S8
and Nb3Sn
provide a new method for fabricating high-field superconductors in which
superconducting materials are made in nanocrystalline form and the very
fine microstructure and high density of defects present are controlled at
the nanoscale to significantly increase the electron scattering and hence
BC2(0). Here we show direct
measurements of BC2(0)
for a series of nanocrystalline niobium materials with an unprecedented maximum
BC2(0) for bulk
Nb of ∼3 T. We provide a theoretical description of our results, using the
well-established fundamental properties of Nb, that explains why the peak in
BC2(0) occurs and can
predict optimal BC2(0)
for other materials in this new class of nanocrystalline high-field superconductors.
125007
Shao-Min Zhou, Sheng Li, Peng Wang, Dong-Qiu Zhao, He-Chun Gong, Bin Zhang, Mei Wang and Xing-Tang Zhang
On the basis of a rather stable wurtzite hexagonal ZnO nanotube (NT)
template confining effect, we give the first report of a new high temperature
superconducting (HTS) cable-like nanostructure in the iron-based oxyarsenide
Sm[O0.8F0.2]FeAs. Scanning electron microscopy, x-ray diffraction, transmission electron microscopy (TEM),
high resolution TEM, selected area electron diffraction and energy-dispersive
x-ray spectroscopy results indicate that the as-fabricated nanocables consist
of two materials: about 50–60 nm diameter single-crystal superconductor
Sm[O0.8F0.2]FeAs
nanowires (cores) and semiconductor ZnO NTs (shells) with outer diameters of about 150 nm and tube walls
up to ∼40–50 nm. The temperature dependence of the DC susceptibility unambiguously demonstrates
a superconducting transition temperature at above 54 K, which indicates potential
applications in hybrid devices combining HTS and ZnO semiconducting properties.
125008
Nuria Del-Valle, Alvaro Sanchez, Carles Navau and Du-Xing Chen
The levitation force and stability of superconducting levitation devices are strongly
dependent on both the geometry and dimensions of the components and the cooling
process of the superconductor. In this work we study these effects in levitating
systems consisting of an infinitely long superconductor and a guideway of different
arrangements of infinitely long parallel permanent magnets. Using a model based on
the critical-state model and a magnetic-energy minimization procedure, taking
into account the demagnetization fields, we analyze the influence of parameters
of the system such as the width and height of the superconductor and those of
the permanent magnets on the levitation force and stability for two different
cooling processes, field cooling and zero-field cooling. The theoretical predictions
are compared with existing experimental data. From the results obtained, we
provide some general trends on how the dimensions of the components of maglev
systems could be chosen to improve both the levitation force and the stability.
125009
Gerhard Gritzner, Heinz Sudra, Herbert Gabriel, Viktor Kavečanský and Jean-Louis Soubeyroux
Bulk material of Nd-doped Tl-1212 superconductors was prepared via a two-step procedure
based on a wet chemical method to prepare precursor material followed by heat-treatment at
895 °C
for 10 h. The samples with Nd stoichiometry of
x = 0.05, 0.1, 0.15, 0.20 0.25 and 0.30 were characterized by XRD, electron microscopy and by resistance
measurements. Oxygen stoichiometry of the specimens was analyzed. Lattice parameters were
derived from x-ray diffraction and neutron diffraction measurements. The increase of the
a-axis and the
decrease of the c-axis as a function of the Nd content are discussed.
125010
E M Tolkacheva, D V Balashov, M I Khabipov and A B Zorin
We propose and demonstrate the functioning of a special rapid single flux
quantum (RSFQ) circuit with frequency-dependent damping. This damping is
achieved by shunting individual Josephson junctions by pieces of open-ended
RC
transmission lines. Our circuit includes a toggle flip-flop cell and Josephson transmission
lines transferring single flux quantum pulses to and from this cell, as well as
DC/SFQ and SFQ/DC converters. Due to the desired frequency dispersion in the
RC
line shunts which ensures sufficiently low noise at low frequencies, such circuits are well
suited for integrating with the flux/phase Josephson qubit and enable its efficient
control.
125011
H Yamasaki, K Ohki, H Yamada, Y Nakagawa and Y Mawatari
125012
Yong Yang
In an actual levitation system composed of high temperature superconductors (HTSs) and
permanent magnets (PMs), the levitating bodies may traverse in arbitrary directions.
Many previous researchers assumed that the levitating bodies moved in a vertical direction
or a lateral direction in order to simplify the problem. In this paper, the vertical and lateral
forces acting on the PM are calculated by the modified frozen-image method when a PM
above an HTS traverses in arbitrary directions. In order to study the effects of
the movement directions on the vertical and lateral forces, comparisons of the
forces that act on a PM traversing in a tilted direction with those that act on a
PM traversing in a vertical direction or a lateral direction have been presented.
125013
Vyacheslav F Solovyov, Qiang Li, Harold Wiesmann, Peter Oleynikov and Yimei Zhu
We correlate the critical current performance of thick film second-generation
YBa2Cu3O7
(YBCO) coated conductors, made by metal–organic deposition,
with specimen grain size. The transport critical current densities,
JcT, of these conductors were observed to be inversely proportional to YBCO grain size in the
5–40 µm
size range. Analysis of magnetic hysteresis curves of the conductors and transmission
electron microscopy data from a large YBCO grain revealed that the reduced
JcT
in tapes with large YBCO grain size is due to the accumulation of secondary phase
precipitates within the grains near the periphery of, and in, the grain boundaries.
Grain size is determined to be one of the important factors in determining
JcT
of YBCO coated conductors made by the metal–organic processes.
125014
Huiqian Luo, Zhaosheng Wang, Huan Yang, Peng Cheng, Xiyu Zhu and Hai-Hu Wen
Single crystals of A1−xKxFe2As2
(A = Ba,
Sr) with high quality have been grown successfully by an FeAs self-flux
method. The samples have sizes up to 4 mm with flat and shiny surfaces. The
x-ray diffraction patterns suggest that they have high crystalline quality and
c-axis orientation. The non-superconducting crystals show a spin-density-wave
(SDW) instability at about 173 and 135 K for the Sr-based and Ba-based
compound, respectively. After doping K as the hole dopant into the
BaFe2As2
system, the SDW transition is smeared, and superconducting samples of the compound
Ba1−xKxFe2As2
(0<x≤0.4) are obtained. The superconductors, characterized by AC susceptibility and resistivity
measurements, exhibit very sharp superconducting transitions at about 36, 32, 27 and 23 K for
x = 0.40,0.28,0.25
and 0.23, respectively.
125015
A Angrisani Armenio, A Augieri, L Ciontea, G Contini, I Davoli, V Galluzzi, A Mancini, A Rufoloni, T Petrisor, A Vannozzi et al
YBa2Cu3O7−δ(YBCO) films
were deposited with a low-fluorine modified trifluoroacetate metalorganic deposition (TFA-MOD) method
on SrTiO3
single crystals and buffered Ni–W metallic tape with a thickness ranging from 450 to
600 nm. The method consists in the substitution of yttrium and copper trifluoroacetates
with Cu and Y acetates dispersed in propionic acid. A reduced pyrolysis time with respect
to the usual TFA method is obtained. Apart from CuO, no traces of second phases
are revealed by x-ray measurements. The films are compact without cracks, and
exhibit a slight superficial porosity, but they still remain well connected, and
therefore the observed porosity does not affect either the critical current density or
the normal state resistivity values, which are indicative of high-quality YBCO
films. Moreover, YBCO films were also obtained on Pd-buffered Ni–W, with a
CeO2/YSZ/CeO2
buffer layer architecture. These films show good morphological, structural, and superconductive
properties with high critical temperature (higher than 91 K) and critical current density higher than
1 MA cm−2
at 77 K in self-field.
125016
Gaoyang Zhao, Huangli Zhang, Yuanqing Chen and Haijun Peng
A YBCO precursor solution was prepared with benzalacetone (BzAcH) as chemical modifier.
The coated gel film using this precursor solution exhibited photosensitivity to UV light at a
wavelength of 325 nm. Based on the photosensitivity of the YBCO gel films, YBCO
patterned films were fabricated by irradiating the gel film with UV light through a mask
followed by dissolving the non-irradiated area in a suitable solvent. After the patterned
YBCO gel films were heat treated, patterned YBCO superconducting films were obtained.
X-ray diffraction (XRD) indicated that the as-prepared patterned YBCO films were highly
c-axis oriented and epitaxially grown on the substrate with a high
Tc
(at zero resistance) of 90.6 K and critical current density
(Jc)
of 0.75 MA cm−2.
125017
P Mele, K Matsumoto, A Ichinose, M Mukaida, Y Yoshida, S Horii and R Kita
YBa2Cu3O7−x+BaSnO3
(YBCO + BSO) mixed films with increasing BSO content were prepared on
SrTiO3
substrates by pulsed laser deposition from
YBCO+x wt% BSO
mixed targets (x = 2, 3, 4, 5, 6, 8 and 9 wt%). Transmission electron microscopy (TEM) images reveal that BSO
is incorporated into the YBCO matrix in form of nanorods, whose density and
size increase with increasing BSO content. The pinning properties for the mixed
YBCO + BSO film were systematically studied. The 4 wt% sample presents the maximum global pinning forces
FP at all considered
temperatures: 28.3 GN m−3
near 2 T at 77 K, 103 GN m−3
near 5 T at 65 K, and>241 GN m−3
near 9 T at 40 K.
125018
Qingping Ding, Yangguang Shi, Hongbo Huang, Shaolong Tang and Shaoguang Yang
PrFeAsO0.75 was
prepared at 900 °C
using the solid state reaction method which shows no superconductivity and a strong resistivity
anomaly at 150 K. The resistivity anomaly was usually ascribed to the spin density wave
(SDW) instability. After further treatment under a high pressure of 6 GPa at a temperature of
1300 °C for 2 h, the
resistivity of PrFeAsO0.75
is two orders lower than that before treatment and a superconducting transition is
observed.
125019
D J Cui, H F Yu, Z H Peng, W H Cao, X B Zhu, Ye Tian, G H Chen, D H Lin, C Z Gu, D N Zheng et al
Macroscopic quantum tunneling (MQT) has been demonstrated recently in a
Bi2Sr2CaCu2O8+δ
surface intrinsic Josephson junction (SIJJ) with its critical current density
Jc below
100 A cm−2 and its
size below 1 µm. In this work, we present a study of the switching current
distributions of SIJJs fabricated on the same crystal, with
Jc>500 A cm−2 and size of
0.8 and 1.6 µm. MQT is clearly observed, and the crossover from MQT to thermal activation
(TA) is seen. Our analysis shows that the data agree well with the theoretical
predictions of MQT and TA for different-sized SIJJs when parameters that roughly
scale with the SIJJ size are used. In the crossover regime, the data are found
to be better fitted by considering quantum corrections to TA. We discuss
the realistic design of phase- and flux-type qubits using the experimentally
attainable SIJJ parameters, which shows that the SIJJs, with their controllable
Jc
and size (or junction capacitance), are feasible for qubit applications in the future.
125020
R S Islam and S H Naqib
The effect of Zn substitution on the superconducting transition temperature,
Tc, was investigated
for the La2−xSrxCu1−yZnyO4
(Zn-LSCO) compounds over a wide range of hole concentrations,
p
(
), and Zn content (y) in the CuO2
plane. A Zn-induced rate of suppression of
Tc,
dTc(p)/dy, was found to
be strongly p-dependent and showed a systematic variation with hole concentration, except in the vicinity of
p∼0.12, i.e. near
the so-called 1/8th
anomaly where the charge/spin stripe correlations are at their strongest in
La2−xSrxCuO4.
Near p∼0.12, the static striped charge ordering is widely believed to dominate the
T–p phase
diagram. dTc(p)/dy
decreased strongly around this hole concentration i.e. Zn became less effective in degrading
Tc
near p∼0.12. This observation is indicative of an intricate and competing interplay among the
superconducting, pseudogap, and stripe correlations in Zn substituted LSCO.
125021
D Bhoi, P Mandal and P Choudhury
We have measured the resistivity of
PrFeAsO1−xFy
samples over a wide range of temperature in order to elucidate the role of
electron–phonon interaction on normal- and superconducting-state properties. The linear
T dependence
of ρ
above 170 K followed by a saturation-like behavior at higher temperature is a
clear signature of strong electron–phonon coupling. From the analysis of the
T dependence
of ρ, we have estimated several normal-state parameters that are useful for understanding the
origin of superconductivity in this system. Our results suggest that Fe-based
oxypnictides are phonon-mediated BCS superconductors like Chevrel phases and A15
compounds.
125022
Wei Yi, Jie Yang, Xiao-Li Shen, Wei Lu, Zheng-Cai Li, Zhi-An Ren, Guang-Can Che, Xiao-Li Dong, Fang Zhou, Li-Ling Sun et al
In this paper, we report a study of superconductivity in the mixed rare earth
La1−xSmxFeAsO0.85
(x = 0–1) compounds prepared by the high pressure (HP) synthesis method.
These compounds have the same crystal structure as the newly discovered
high-Tc
REFeAsO1−δ
family (RE = rare
earth metal), and the onset superconducting critical temperature
(Tc) in
these compounds increases monotonically to 55 K from 31.2 K with increasing amount of Sm doping
from x = 0
to 1.
125023
M Zehetmayer, N Hörhager and H W Weber
We present a new method of rapidly determining the local critical current density
(Jc) in large superconducting pellets without destroying the sample. We show that magnetoscan
data averaged over a certain small sample area can be mapped directly onto absolute values of
Jc. This conclusion and the corresponding calibration curve are based on results from
magnetoscan and from SQUID measurements of the same sample regions, which were found
to show an excellent correlation. Numerical simulations help to extend the calibration
curve, to improve the resolution of the method and to reduce possible errors.
125024
Huiqian Luo, Peng Cheng, Lei Fang and Hai-Hu Wen
Bi2Sr2−xLaxCuO6+δ
(0≤x≤1.00) single crystals with high quality have been grown successfully using the
traveling-solvent floating-zone technique. The patterns of x-ray diffraction suggest
high crystalline quality of the samples. After post-annealing in flowing oxygen at
600 °C, the
crystals show sharp superconducting transitions revealed by AC susceptibility. The hole concentration
p
is deduced from the superconducting transition temperature
(Tc), which exhibits a linear relation with La doping level
x. It ranges from the heavily overdoped regime
(p≈0.2) to the extremely
underdoped side (p≈0.08) where the superconductivity is absent. Comparing with the superconducting dome in the
Bi2+xSr2−xCuO6+δ
system, the effects from out-of-plane disorders show up in our samples. Besides the La doping level
x, the superconductivity is also sensitive to the content of oxygen which could be tuned by
the post-annealing method over the whole doping range. The post-annealing effects on
Tc
and p
for each La doping level are studied and give some insights on the differences in nature
between the overdoped and underdoped regimes.
125025
J Du, A D Hellicar, L Li, S M Hanham, N Nikolic, J C Macfarlane and K E Leslie
A high-Tc
superconducting (HTS) detector based on a
YBa2Cu3O7−x
(YBCO) step-edge Josephson junction has been developed and applied to terahertz (THz)
detection. The detector was coupled to a ring-slot antenna designed for operation at
600 GHz, and used for THz imaging. The results suggest that the characteristic voltage
and frequency of our HTS step-edge junctions can be readily optimized for the
chosen THz frequency range at easily achievable temperatures. The images also
clearly demonstrate some of the unique properties of THz radiation, including the
sensitivity to water content and the ability to penetrate packaging materials.
125026
E Bemporad, F Carassiti, M Sebastiani, G Lanza, V Palmieri and H Padamsee
The aim of the present research activity was to verify the influence of the applied bias
voltage on the microstructural and functional properties of magnetron sputtering physical
vapour deposition (MS-PVD) niobium thin films for use in superconducting resonant
cavities for particle accelerators.
Four different sets of samples were produced, by varying both the applied bias
voltage and the nature of the substrate (copper or quartz). The morphological,
microstructural, and mechanical properties of the coatings were experimentally
determined by focused ion beam scanning electron microscopy (FIB-SEM), atomic force
microscopy (AFM), transmission electron microscopy (TEM), and nanoindentation
techniques, and then correlated to the applied bias and nature of the substrate.
The superconducting properties (critical temperature
Tc
and residual resistivity) were determined by a calibrated four-contact probe and a
cryogenic apparatus.
The microstructures and surface properties of biased films grown on copper and quartz
were compared. The observed differences are likely connected to the low conductivity of
quartz that induces a re-sputtering effect and a consequent modification of the
superconducting performances.
125027
Lu Ji and Judy Z Wu
The microwave power handing capability
Pc
of the microstrip lines of the isomorphic ‘1212’ pair is studied for the superconductors
TlBa2CaCu2O7 and
HgBa2CaCu2O6+δ at
≥77 K.
The Pc
for the pair follows the same temperature dependence at a reduced temperature scale
(t = T/Tc). A comparison of the dc critical current density
Jc and the
radio-frequency one Jrf
derived from the Pc
of the ‘1212’ pair reveals a similar reduced temperature dependence, suggesting that the depinning
of the magnetic vortices, which is dictated by the ‘1212’ structure, pays a similar role in limiting
Jc and
Jrf in the
proximity of Tc.
125028
T Nomura, S W Kim, Y Kamihara, M Hirano, P V Sushko, K Kato, M Takata, A L Shluger and H Hosono
Undoped LaFeAsO, the parent compound of the newly found
high-Tc
superconductor, exhibits a sharp decrease in the temperature-dependent resistivity at
∼160 K. The anomaly can be suppressed by F doping with simultaneous appearance of
superconductivity appears correspondingly, suggesting a close association of the anomaly
with the superconductivity. We examined the crystal structures, magnetic properties
and conductivity of undoped (normal conductor) and 14 at.% F-doped LaFeAsO
(Tc = 20 K) by synchrotron x-ray diffraction (XRD), DC magnetic measurements, and ab initio
calculations demonstrated that the anomaly is associated with a phase transition from tetragonal
(P4/nmm) to
orthorhombic (Cmma) phases at ∼160 K as well as an antiferromagnetic spin ordering transition at
∼140 K. These transitions can be explained by spin configuration-dependent potential energy
surfaces derived from the ab initio calculations. The suppression of the transitions is ascribed to
interrelated effects of geometric and electronic structural changes due to doping by
F−
ions.
129901
The PDF file provided contains web links to all articles in this volume.