RAPID COMMUNICATION
112001
Zhaoshun Gao, Lei Wang, Yanpeng Qi, Dongliang Wang, Xianping Zhang, Yanwei Ma, Huan Yang and Haihu Wen
We report the fabrication of Ta-sheathed superconducting
SmFeAsO1−xFx
wires by the powder-in-tube method for the first time. The transition temperature of the
SmFeAsO0.65F0.35
wires was confirmed to be as high as 52 K. High critical fields
Hc2(0)≥120 T as well as
current density Jc
of 3900 A cm−2
at 5 K were also demonstrated. It should be noted that the
Jc
exhibits a very weak field dependence behavior, indicating a very encouraging prospect for
application of the new superconductors.
PAPERS
115001
L Kopera, P Kováč and T Melišek
This paper describes the design and performance of a new tension test instrument
for measuring stress–strain characteristics of a freestanding sample and critical
current degradation of superconducting wires and tapes under variable tension and
magnetic fields. The performance of the instrument has been tested at liquid nitrogen
and liquid helium temperature up to a tensile force of 1000 N. Stress–strain and
Ic–strain characteristics of advanced Bi-2223, Y-123 and
MgB2
composite superconductors were measured. The results show the best electromechanical
properties for the tapes mechanically reinforced by soldered stainless steel strips.
MgB2
tape with a Ti-barrier and Monel sheath is less reinforced due to an
apparent softening of these materials during the final annealing at
800 °C/30 min.
115002
D C van der Laan and J W Ekin
A new method to measure the effect of in-plane bending on the critical current of
YBa2Cu3O7−δ
coated conductors is presented. Such a bending mode can be important in transmission
cables, saddleback magnets, and double-pancake windings. A linear strain distribution over
the width of the conductor develops in this bending mode, where one half of the conductor
is under axial compressive strain and the other half is under axial tensile strain. A
reversible reduction in critical current of up to 5% is measured in 4 mm wide conductors at
a critical bending radius of 0.25–0.28 m. The critical current degrades irreversibly for
bending radii less than this because the strain at the edge of the conductor that is under
tension irreversibly damages the conductor. The results are described by use of
a model that calculates the critical current as a function of in-plane bending
radius by taking into account the strain gradient over the width of the sample
and the measured dependence of the critical current on axial strain. A similar
approach can be used to calculate the degradation of the critical current n of
other deformation modes, such as torsion, or other more complex geometries.
115003
A Lucarelli, A Frey, R Yang, G Lüpke, T J Haugan, G A Levin and P N Barnes
The current density evolution in
YBa2Cu3O7−δ
thin films is studied by time-resolved magneto-optical imaging as a function of the phase of
an ac current applied simultaneously with a perpendicular dc magnetic field. We present a
new empirical method to separate the total current distribution into a circulating current,
which screens the applied field, and the applied transport current. The latter shows an
asymmetric profile with pronounced peaks at the edges of the sample and its
phase-dependent self-field is contained in the flux region bound by the circulating current.
Threading dislocations provide the necessary pinning sites for the observed high local
values of the transport current.
115004
Y Zhang, X Xu, Y Zhao, J H Kim, C Lu, S H Zhou and S X Dou
The particle size, purity and form of the starting boron powders
play an important role in the superconducting properties of
MgB2. In
this paper high-purity (99.999%) boron powders with crystalline phase that were processed by ball
milling have been used as the precursor powders. It was observed that the critical current density
(Jc) value
was 9.1 × 103 A cm−2
at 5 K and 8 T, which is two times higher than for a sample with
ball-milled amorphous boron powders, and a factor of 40 higher than a
sample made from as-supplied amorphous boron powders. Significant
Jc
improvement at high fields is attributed to the
Hc2
enhancement caused by the increased disorder.
115005
Y He, X Xiang, F M Ji, Xianxi Dai and JiXin Dai
Resistivity, especially anisotropic resistivity, is an interesting property in many materials.
In this paper a line current (LC) method is presented. For large crystal samples, there is no
difficulty in obtaining all components of their resistivity tensors by this LC method.
However, it is difficult to measure the component in the vertical direction of thin films and
one must make three independent measurements. For a given thin film, for the LC method,
one can have only two independent designs for the probe configurations. In this
paper, a theory for measuring the resistivity of anisotropic crystals based on two
films with two orientations is proposed, which can be applied to films and bulk of
high-Tc
superconductors or semiconductors. The insensitivity of certain components in the
measurement is solved through the arrangement of probes on the crystal. The method can
be widely applied, and an exact universal correction function in practice, expressed by
composite elementary functions, is obtained.
115006
V A Seleznev, M A Tarkhov, B M Voronov, I I Milostnaya, V Yu Lyakhno, A S Garbuz, M Yu Mikhailov, O M Zhigalina and G N Gol’tsman
We report on the fabrication and investigation of few-nanometers-thick superconducting
molybdenum–rhenium (Mo–Re) films intended for use in nanowire single-photon
superconducting detectors (SSPDs). Mo–Re films were deposited on sapphire
substrates by DC magnetron sputtering of an Mo(60)–Re(40) alloy target
in an atmosphere of argon. The films 2–10 nm thick had critical temperatures
(Tc) from 5.6 to 9.7 K. HRTEM (high-resolution transmission electron microscopy)
analysis showed that the films had a homogeneous structure. XPS (x-ray
photoelectron spectroscopy) analysis showed the Mo to Re atom ratio to be
0.575/0.425, oxygen concentration to be 10%, and concentration of other elements to be 1%.
115007
J K Shin, S Ochiai, H Okuda, M Sugano and S S Oh
The critical current at 77 K of multifilamentary Bi2223 composite tape was studied under applied
tensile strain experimentally and analytically. Beyond the irreversible strain, the critical currents
(IC) decreased significantly with increasing applied tensile strain
(εc), due to the enhanced cracking of the Bi2223 filaments. The voltage generation
in the voltage–current relation was calculated by the current share model
in which the transport current is shared by the Bi2223 filament and Ag
near the cracked portion. Then the critical current was estimated with a
1 µV cm−1
criterion. By the application of the current share model to the experimental result, the
effective crack length responsible for the reduction in critical current was estimated, with
which the change of critical current could be described satisfactorily as a function of
applied strain.
115008
P Diko, X Chaud, V Antal, M Kaňuchová, M Šefčíková and J Kováč
As-grown YBa2Cu3O7
bulk superconductors have low oxygen content,
YBa2Cu3O6.3, are not superconducting, and must be oxygenated to form
YBa2Cu3O7. During standard
oxygenation at 400 °C
the shortening of crystal lattice parameters causes intensive cracking. The created cracks
allow oxygen penetration into the bulk and cause the oxygenation time to be
technologically acceptable but reduce significantly the superconducting properties. Here we
show that it is possible to eliminate the formation of oxygenation cracks and to reach a
critical current density 2.5 times higher than in bulk oxygenated in a standard way. The
oxygenated crack-free samples were obtained by high pressure oxygenation with
progressively increasing oxygen partial pressure.
115009
Hui Dong, Yongliang Wang, Shulin Zhang, Yue Sun and Xiaoming Xie
Nuclear magnetic resonance in the Earth’s magnetic field was studied
in an urban laboratory without shielding using a second-order
low-Tc
SQUID (superconducting quantum interference device) gradiometer. Two different
configurations were investigated, one with a prepolarization field perpendicular
to the measurement field and the other one with the two fields parallel but a
π/2 AC
pulse applied perpendicular to them. With a prepolarization field of 10 mT and a measurement field
of ∼29.1 µT, the proton signal from 15 ml tap water was obtained in a one-shot
measurement with high signal-to-noise ratio, and the signal was still
discernible down to a sample volume of 2–3 ml. Spin–lattice relaxation time
T1∼1.78 s was
measured from the variation of signal magnitude on the prepolarization time. Spin–spin relaxation
time T2
was estimated to be around 0.9 s from the calculated FID signal by using a special method
developed based on the principle of a lock-in amplifier.
115010
Yuhu Zhai and Mark D Bird
Performance degradation of Nb3Sn
cable-in-conduit-conductors (CICCs) is a critical issue in large-scale magnet design
such as in the International Thermonuclear Experimental Reactor (ITER) and
the series-connected hybrid (SCH) magnets currently under development at the
National High Magnetic Field Laboratory (NHMFL). The critical current Ic of
Nb3Sn
conductors is strongly affected by thermal pre-strain in strand filaments in a CICC from
differential thermal contraction between strands and conduit during cooling down after
heat treatment. Mitchell and Nijhuis recently introduced strand bending under
locally accumulated Lorentz force for the interpretation of observed transverse
load degradation, defined as the Ic reduction due to strand bending and contact
stress at strand crossing with respect to the expected Ic from strand data at
the thermal compressive strain. In this paper, a new numerical model of CICC
performance has been developed based upon earlier work by Mitchell and Nijhuis.
The new model, called the Florida electro-mechanical cable model (FEMCAM),
combines the thermal bending effects during cooling down and the electromagnetic
bending effects during magnet operation, as well as effects due to strand filament
fracture. We present the FEMCAM formulation and benchmark the results against
about 40 conductor tests of first-cycle performance and 20 tests that include cyclic
loading. We also consider the effects of different jacketing materials on CICC
performance. We conclude that FEMCAM can be a helpful tool for the design of
Nb3Sn-based
CICCs and that both thermal bending and transverse bending play important roles in the performance
of Nb3Sn
CICCs.
115011
Jun Lu, Vince Toplosky, Ke Han, Todd Adkins, Scott T Bole and Robert P Walsh
The inter-strand contact resistance
(RC)
of Nb3Sn
cable-in-conduit conductors (CICCs) is a very important parameter which strongly correlates
with ac losses and current redistribution behavior of the CICCs. One way to obtain the desired
RC
is to apply a layer of hydrocarbon oil on the
Nb3Sn strands before
the CICC Nb3Sn
reaction heat treatment. In this paper, we measured
RC for
a Nb3Sn
CICC sample fabricated with hydrocarbon oil. The measurements were performed using an
apparatus designed to apply transverse load and load cycling on CICCs at 4.2 K. Resistances
RC
between strands of different cabling stages were measured with transverse load up to
188 kN m−1
and load cycles up to 10 000. The results show that
RC
of the sample increases almost linearly with the first loading. With load cycling,
RC
increases rapidly at first, but becomes saturated after
∼100 cycles. After
10 000 load cycles, RC
decreases with increasing load at a decreasing rate. These behaviors are comparable to
observations for CICC with Cr plated strands reported in the literature. Therefore from the
RC point
of view, Nb3Sn
CICCs with hydrocarbon oil on strands may be used as a low cost alternative to CICCs
with Cr plated strands.
115012
Min Liu, Hongli Suo, Shuai Ye, Dongqi Shi, Yue Zhao, Xiao Tang, Lin Ma, Qi Li, Lin Wang, Meiling Zhou et al
YBa2Cu3O7−δ
(YBCO) films with Zr doping have been prepared successfully by the
trifluoroacetate metal–organic deposition (TFA-MOD) method through dissolving
Zr acetylacetonate in the precursor solution. Yttria-stabilized zirconia (YSZ)
nanoparticles were detected in the doped YBCO films by x-ray diffraction
(XRD) and scanning electron microscopy (SEM). From the analysis of XRD
ω
and φ
scans, the doped films have better out-of-plane and in-plane textures than those of the un-doped
YBCO film. Although the doped YBCO films have a lower critical transition temperature
(Tc)
than that of un-doped YBCO film, a very significant enhancement of critical current density
(Jc)
is displayed as compared to the un-doped film at high applied fields. A high
Jc near
106 A cm−2 at 1 T
and a Jc
of 105 A cm−2
at 5 T were observed in 6% doped Zr film, which are 5 times and 25 times the
Jc
values of the un-doped film in the same applied fields, respectively, indicating an optimal
defect density created by 6% Zr doping.
115013
Anjana Asthana, A Matsumoto, H Kitaguchi, Y Matsui, T Hara, K Watanabe, H Yamada, N Uchiyama and H Kumakura
We performed structural–microstructural investigations of pure
MgB2, ethyltoluene and both ethyltoluene- and SiC-added
MgB2/Fe
tapes. The analysis of the microstructure shows that the grain size for the pure and ethyltoluene-added
MgB2
tape sample is in the range of 10–100 nm. However, with the addition of
both ethyltoluene and SiC, the grain size decreases to about 5–80 nm. The
a-axis length of the ethyltoluene-added tape samples is slightly
decreased, whereas for both ethyltoluene- and SiC-added samples, the
a-axis length is decreased by 0.4% as compared to the pure
MgB2
tape sample, showing the amount of carbon substitution is less
in ethyltoluene-added tape samples. The reason for the higher
Jc values of the
ethyltoluene-added MgB2
tape sample as compared to the pure
MgB2
tapes is the presence of a lesser amount of the impurity phase, MgO. The large improvement in
Jc–B
properties for the ethyltoluene- and SiC-added
MgB2
tape sample is attributed to (1) the enhancement of upper critical field,
Bc2, by the substitution of carbon for boron, (2) pinning by nanosized (5–20 nm) particles of
Mg2Si
and other silicides, (3) enhanced grain boundary pinning due to the smaller grain size and
(4) the presence of a lesser amount of impurity phase, MgO, as compared to the pure
sample.
115014
Y L Chen, Y J Cui, Y Yang, Y Zhang, L Wang, C H Cheng, C Sorrell and Y Zhao
Ta-sheathed SmFeAsO0.8F0.2
superconducting wires with Tc = 52.5 K have been fabricated using the powder-in-tube (PIT) method and the superconducting
properties of the wires have been investigated. The wires exhibit a very large intragrain
critical current density at a temperature below 30 K. A peak effect with maximal
Jc = 0.6 MA cm−2
at 10 K under 6 T field was observed. The peak field
Hpear
is strongly temperature-dependent. A severe weak-link effect depresses the development of
global supercurrent owing to a very short coherence length. The wires also show a power
law temperature dependence for the irreversibility line with
. The H–T
phase diagram was found to be similar to that of other superconducting cuprates.
115015
M Pissas, Y Sanakis, V Psycharis, A Simopoulos, E Devlin, Zhi-An Ren, Xiao-Li Shen, Guang-Can Che and Zhong-Xian Zhao
Using Mössbauer spectroscopy, we have studied the oxypnictide superconductor
REFeAsO0.82F0.18
with RE = Nd
for the first time. The Mössbauer spectra at 295 K predominantly
consist of a singlet (94% of the spectral area) with an isomer shift
δ = 0.43(1) mm s−1 with respect to
α-iron at 295 K, and a
minor doublet with δ = 0.29(1) mm s−1
and ΔEQ = 1.756(3) mm s−1, which is
attributed to an FeAs2
impurity. The spectrum remains fundamentally unchanged down to
4.2 K. The isomer shift of the singlet with zero quadrupole splitting
indicates that the iron in the Nd oxypnictide is probably in a low spin
Fe2+
(S = 0) state.
The temperature variation of the isomer shift can be reproduced assuming a Debye-type phonon spectrum
with ΘD = 430 K.
115016
Yanpeng Qi, Zhaoshun Gao, Lei Wang, Dongliang Wang, Xianping Zhang and Yanwei Ma
Here we report the synthesis and characterizations of
SmFe1−xCoxAsO
(x = 0.10,
0.15) for the first time. The parent compound SmFeAsO itself is not superconducting
but shows an antiferromagnetic order near 150 K, which must be suppressed by
doping before superconductivity emerges. With Co doping in the FeAs planes,
antiferromagnetic order is destroyed and superconductivity occurs at 15.2 K. Similar to
LaFe1−xCoxAsO,
the SmFe1−xCoxAsO
system appears to tolerate considerable disorder in the FeAs planes. This result is
important, suggesting a different mechanism for cuprate superconductors compared to the
iron-based arsenide ones.
115017
P Badica, G Aldica, T Craciunescu, I Tiseanu, Y Ma and K Togano
It is shown that x-ray microtomography (XRT) is a powerful technique to observe
on extended volumes the morphology, alignment and local bulk density in
MgB2
tapes, thin films and especially bulk specimens. For the bulk samples obtained from
mechanically milled powders for different conditions, several types of the 3D microstructural
patterns were observed. These significant differences between the samples were not revealed
by SEM. Microtomography can be a useful additional technique to characterize the samples
and to obtain unique information, e.g. on local bulk density, but it cannot replace the
existing methods: advantages and limitations are discussed. It is concluded that the
method is promising and further developments are expected to be helpful for a better
understanding of the complex processing-microstructure-properties relationship in the
MgB2
superconductor.
115018
Z Deng, J Wang, J Zheng, H Jing, Y Lu, G Ma, L Liu, W Liu, Y Zhang and S Wang
In order to improve the cost performance of the present
high-Tc
superconducting (HTS) Maglev vehicle system for practical application, the multi-pole
permanent magnet guideway (PMG) concept was introduced. A well-known double-pole
Halbach PMG was chosen as a representative of multi-pole PMGs to compare with
traditional monopole PMGs from the point of view of levitation efficiency and cost.
Experimental results show that YBCO bulks above the double-pole Halbach PMG can
exhibit better load capability and guidance performance as well as dynamics stability at
the applied working height between the bulk HTSC and the PMG due to a more reasonable
magnetic field distribution at the working range of bulk HTSC. Furthermore, the
double-pole PMG configuration can play a more important role in improving guidance
performance due to the potential-well field configuration. By comparing with former
‘century’ PMGs, the double-pole Halbach PMG shows another remarkable advantage in
reducing the cost of levitation. As another necessary issue, magnetic field homogeneity
and the corresponding magnetic drag force of a double-pole Halbach PMG has
been considered by experiment in spite of the above highlights. Synthetically,
the multi-pole Halbach PMG design is concluded to be one important choice for
future HTS Maglev vehicle applications because of its high efficiency and low cost.
115019
M Sugano, T Nakamura, T Manabe, K Shikimachi, N Hirano and S Nagaya
A new experimental set-up was developed to evaluate the strain dependence of critical current
(Ic(εa))
for YBa2Cu3O7−δ
(YBCO)-coated conductors under a magnetic field in a variable temperature environment.
In this paper, we report the first results on the effect of a magnetic field parallel to the
c
axis (
) on Ic(εa)
up to 10 T at temperatures of 60–77 K. We found that the magnetic field affects
Ic(εa)
in a different manner, depending on the field region. When the magnetic field increases from
B = 0 T,
normalized Ic(εa)
is first improved and the optimal situation is realized under the characteristic magnetic field of
Bp = 0.2 T at
77 K and Bp = 0.4 T at 70 K, respectively. For higher magnetic field,
Ic(εa) degrades
further with increasing strain. From the results of a fitting analysis, we confirmed that the strain at the
peak of Ic(εa)
shifts to higher strain and reaches the maximum value at
Bp. The
peak shift as a function of magnetic field found in the YBCO-coated conductors is in contrast with
the Ic(εa)
behavior for conventional low temperature superconducting composites, in which all of the
critical parameters are optimized when the intrinsic strain of the superconductor
is zero. From the present result, we can conclude that the peak strain of the
Ic(εa)
curve under a magnetic field is not determined only by the thermal residual strain of the
YBCO film in the coated conductor. For the high field region, the curvature of the
Ic(εa)
curve increases with increasing magnetic field and temperature. It results in a steep decrease in
Ic(εa)
at high magnetic fields and temperatures.
115020
N Banno, T Takeuchi, S Nimori, K Tanaka, K Nakagawa and K Tsuchiya
This paper focuses on the magnetization characteristics of technical
Nb3Al
conductors, in particular the minimization of their hysteresis loss and low-field instability. Unlike the case
of Nb3Sn wire
fabrication, the Nb3Al
wire is fabricated by a phase transformation process, in which it is believed that the
Jc properties of
the transformed Nb3Al
phase do not depend on the filament size or shape, but rather are principally controlled by
the rapid heating and quenching or transformation conditions. However, the rapid heating
and quenching process forces us to use high-melting-point metals like niobium as the
matrix. The use of Nb strongly affects the magnetization because of its superconductivity
in low fields. In this paper, the magnetization properties of several kinds of technical
Nb3Al
conductors, including Ta matrix wires, were studied. The use of Ta was effective in
suppressing low-field instability. In addition, we propose a new process to further minimize
the filament diameter by a re-stacking (RS) method, whereby the rapidly quenched strands
are re-stacked into a stabilizing material tube and co-drawn. This process leads
to a very fine multifilamentary structure with a filament diameter of less than
15 µm, thereby substantially reducing the magnetization, as compared with high-performance
Nb3Sn wires, e.g.
RRP Nb3Sn wire. The
± 3 T hysteresis loss of
the RS Nb3Al conductor was
370 mJ cm−3 and the non-Cu
Jc (12 T, 4.2 K) of the
conductor was 1350 A mm−2. These values meet the ITER strand specification.
115021
J Hänisch, F M Mueller, S Ashworth, J Y Coulter and V Matias
The transverse Jc
distribution in YBCO coated conductors was measured non-destructively with high resolution
using a ‘magnetic knife’ made of permanent magnets. The method utilizes the strong depression of
Jc
in applied magnetic fields. A narrow region of low (including zero) magnetic field, in a
surrounding higher field, is moved transversely across the sample in order to reveal the
critical-current density distribution. The net resolution of this device is approximately
65 µm, and
the Jc
resolution is better than 0.5%. A Fourier series inversion process was used to determine the transverse
Jc distribution in
the sample. The Jc
profile was correlated with other sample properties of coated conductors prepared by
pulsed laser deposition. Because of its straightforward and inexpensive design, this
Jc
imaging technique can be a powerful tool for quality control in coated-conductor
production.
115022
Ali E Aliev
Tungsten trioxide, WO3−y, infiltrated into various nanoporous matrix structures such as carbon inverse opal, carbon
nanotube paper or platinum sponge, and then intercalated with alkaline ions
(Li+,
Na+) exhibits a pronounced diamagnetic onset in ZFC magnetization in a wide range
of temperatures, 125–132 K. Resistivity measurements show nonzero jump and
intensive fluctuations of electrical resistance below observed transition points. The
observed magnetic and electrical anomalies in nanostructured tungsten bronzes
(LixWO3−y
and NaxWO3−y) suggest the possibility of localized non-percolated superconductivity.
115023
J B Song, K L Kim, K J Kim, J H Lee, H M Kim, W S Kim, S W Yim, H-R Kim, O B Hyun and H G Lee
In general, conventional high-Tc
superconducting fault current limiters (SFCLs) are operated by cooling systems with a
liquid cryogen, such as liquid nitrogen (LN2). However, in the fault mode, LN2 evaporates
because of joule heating in the SFCL module, so the SFCL system experiences an enormous
increase in nitrogen gas volume. In this case, the thermal stability and protection of the
system become the primary concerns for the design of the SFCL cooling system. In order to
enhance the thermal stability and safety of the system, an SFCL cooled by solid
nitrogen (SN2) as a large heat capacitor has been proposed as an alternative. In this
paper we report the quench/recovery characteristics of a YBCO-coated conductor
(CC) evaluated in an SN2 cooling system for the SFCL. A feasibility study is also
conducted on the reference design codes and thermal requirements for the optimal
design of the SN2 cooling system. The results demonstrate that the improved
thermal contact obtained between the SN2 cooling system and the SFCL module
renders the proposed system a suitable cryogen for the SFCL module. Detailed
experimental results for the LN2 and SN2 cooling systems are presented and
discussed.