Focus Papers
024001
Bhagyesh Purohit, Sagarmal Kumawat and Ambesh Dixit
We explored the photocatalytic degradation of industrial dye methylene blue extensively using inorganic BiVO4—organic graphitic carbon nitride (C3N4) composite material system. The composite BiVO4/C3N4 is synthesized and X-ray diffraction confirmed the presence of both monoclinic BiVO4 and graphitic carbon nitride in composite material. The vibration mode at 805 cm−1 supports the presence of triazine ring in carbon nitride. We observed degradation of methylene blue in 300 and 135 min using BiVO4 and C3N4 materials independently. The investigated BiVO4/C3N4 composite photocatalyst showed drastic enhancement in photoresponse and about 60% degradation of methylene blue is observed in initial 15 min after irradiating light, whereas complete degradation is observed in about 60 min. The enhanced photocatalytic response is attributed to modified electronic properties of the inorganic BiVO4—organic graphitic C3N4 composite system.
024002
L Vimala Devi, S Sellaiyan, S Sankar and K Sivaji
The effect of La dopant concentration (4% and 6%) and annealing (400, 600 and 800 °C) behavior of CuO derived by solution combustion method (SCS) are investigated. Structural and optical properties were studied by XRD, SEM, diffuse reflectance spectra (DRS) and photoluminescence (PL) measurements for the prepared samples. The crystallinity of the samples increases with temperature. Incorporation of La in CuO lattice reduces the crystallinity due to the variation of ionic radii and also leads to higher angle peak shift. From SEM micrograph, it is clear that annealed samples increases the nucleation rate and agglomerates the particles. DRS study revealed the narrowing of the bandgap in doped CuO compared to undoped CuO, which is due the influence of La3+ impurity dopant ions on the electronic states of the crystallite. The band broadening in higher concentration of impurity is due to the partial curing of copper vacancies. The luminescence spectra show that there is no change in peak position but slight variation in the peak intensity related to the defect change in the CuO due to La doping. La induces the lattice distortion, increases the defect concentration in CuO and it acts as a quencher. Bandgap shift and quenching of PL intensity may provide excellent degradation efficiency of dye by the design of rare earth doped CuO-based photocatalyst.
024003
G Devanand Venkatasubbu, S Nagamuthu, T Anusuya, J Kumar, Ramachandran Chelliah, Sudha Rani Ramakrishnan, Usha Antony, Imran Khan and Deog-Hwan Oh
Chitosan titanium dioxide nanocomposite has been used for wound healing. Titanium dioxide (TiO2) nanoparticles are synthesised and made in to nanocomposite along with chitosan. Curcumin nanoparticles are synthesised. Three different drugs with antimicrobial activity are incorporated into the chitosan/TiO2nanocomposite. Ciprofloxacin, amoxicillin and curcumin nanoparticles are incorporated within the chitosan/TiO2 nanoparticles. The nanoparticles and nanocomposite are characterized with XRD, FTIR, TEM and SEM. Drug loading was found to be around 45% for all the three drug molecules. The drug release profile shows a controlled release of drug molecules from the nanocomposite. Antibacterial studies shows a good inhibition of bacterial species by the nanocomposites.
024004
K Bhuvaneswari, R Divya Bharathi and T Pazhanivel
Photocatalytic degradation of toxic organic pollutant is a challenging tasks for environmental protection. Recently most of the researchers are focusing on metal oxide semiconductors, such as TiO2, ZnO, and SnO2 as efficient photocatalysts for photocatalytic degradation of organic pollutant. In this regard, we are eager to increase the photocatalytic activity with the help of organic molecule (Silk Fibroin (SF)). Metal oxides are attached on the surface of SF with the help of polyvinyl alcohol (PVA). In this present work, pure SnO2, (Cd/Zn) doped SnO2 and SF linked nanoparticles have been successfully synthesized by microwave technique. The synthesized samples were investigated by XRD, FTIR and UV-DRS techniques. The surface morphology of all the samples were investigated by FESEM analysis. Photocatalytic activities of Cd doped SnO2 nanoparticles and SF attached Cd/Zn doped SnO2 nanoparticles were studied on methylene blue (MB) dye under UV–vis light illumination.
024005
Arie Wibowo, Radian Febi Indrawan, Untung Triadhi, Akfiny Hasdi Aimon, Ferry Iskandar and Husaini Ardy
Heterogeneous fenton catalyst is one of the attractive technologies for destruction of persistent and non-biodegradable pollutant in wastewater, because it can be used in wide range of pH and recyclable. Herein, commercial bacterial celluloses (BCs) were used as an alternative support of fenton catalyst to improve their catalytic activity. Scanning Electron Microscope (SEM) observations indicated that the presence of BCs and decreasing precursor concentration might promote formation of smaller particle sizes of catalyst from 3.5 μm of bare catalyst to 0.7 μm of catalyst@BC. UV–vis measurement showed that fast degradation of dyes with half-time degradation at around 25 min was observed in sample using catalyst@BCs with precursor concentration of 0.01 M. Successful preparation of heterogeneous fenton catalyst with smaller particle size and better catalytic activity is important for their application in wastewater treatment.
024006
Sayari Biswas and Asit Kumar Kar
Titanium dioxide (TiO2) thin films were synthesized by hydrothermal assisted sol-gel dip coating method on quartz substrate. The sol was prepared by hydrothermal method at 90 °C. Dip coating method was used to deposit the thin films. Later films were annealed at four different temperatures −600 °C, 800 °C, 1000 °C and 1200 °C. XRD study showed samples annealed at 600 °C are almost amorphous. At 800 °C, film turns into anatase phase and with further increment of annealing temperature they turn into rutile phase. Transmission spectra of thin films show sharp rise in the violet-ultraviolet transition region and a maximum transmittance of ∼60% was observed in the visible region for the sample annealed at the lowest temperature. Band gap of the prepared films varies from 2.9 eV to 3.5 eV.
024007
J William Brown, P S Ramesh and D Geetha
We report fabrication of mesoporous Fe doped CuS nanocomposites with uniform mesoporous spherical structures via a mild hydrothermal method employing copper nitrate trihydrate (Cu (NO3).3H2O), Thiourea (Tu,Sc(NH2)2 and Iron tri nitrate (Fe(No3)3) as initial materials with cationic surfactant cetyltrimethylamoniame bromide (CTAB) as stabilizer/size controller and Ethylene glycol as solvent at 130 °C temperature. The products were characterized by XRD, SEM/EDX, TEM, FTIR and UV analysis. X-ray diffraction (XRD) spectra confirmed the Fe doped CuS nanocomposites which are crystalline in nature. EDX and XRD pattern confirmed that the product is hexagonal CuS phase. Fe doped spherical structure of CuS with grain size of 21 nm was confirmed by XRD pattern. Fe doping was identified by energy dispersive spectrometry (EDS). The Fourier-transform infrared (FTIR) spectroscopy results revealed the occurrence of active functional groups required for the reduction of copper ions. Studies showed that after a definite time relining on the chosen copper source, the obtained Fe-CuS nanocomposite shows a tendency towards self-assembly and creating mesoporous like nano and submicro structures by TEM/SAED. The achievable mechanism of producing this nanocomposite was primarily discussed. The electrochemical study confirms the pseudocapacitive nature of the CuS and Fe-CuS electrodes. The CuS and Fe-CuS electrode shows a specific capacitance of about 328.26 and 516.39 Fg−1 at a scan rate of 5 mVs−1. As the electrode in a supercapacitor, the mesoporous nanostructured Fe-CuS shows excellent capacitance characteristics.
024008
Kalimuthu Rajendran and Nagappan Rajendiran
A simple, economical, and green method for the preparation of water soluble, high fluorescent carbon quantum dots (CQDs) has been prepared via hydrothermal process using jackfruit (Artocarpus heterophyllus) as a carbon source. The optical properties of synthesized CQDs were characterized by UV- visible and fluorescence spectroscopy. Fourier transform infrared spectroscopy (FT-IR), x-ray Diffraction (XRD) and high resolution transmission electron microscopy (HR-TEM) techniques were used to study the composition and size of the CQDs. The prepared CQDs were spherical in shape with an average size of 2.5 nm along with uniform distribution and showed bright bluish green emission properties, without any further surface modification. The prepared CQDs were exhibit high stability at neutral pH and showed high photo-stability under UV light irradiation at 365 nm. The obtained CQDs were effectively utilized as fluorescent probe for highly selective and sensitive detection of Hg2+ and Cr6+ ions in environmental samples with a limit of detection of about 8 and 10 nM respectively.
Papers
Nanomaterials and nanostructures
025001
Changqing Jin, Kexin Zhu, Zengyun Jian, Yongxing Wei, Ling Gao, Zhihong Zhang and Deshan Zheng
Mesoporous C@ZnO hollow spheres were successfully synthesized through a carbon-sphere template combined hydrothermal method. The photocatalytic activities of the samples to rhodamine B (RhB) were investigated, and the sample of 3 wt% carbon has the best photocatalytic activity to RhB. The excellent photocatalytic performance could come from both enhanced photogenerated electron–hole pair separation, and the larger specific surface area induced by mesoporous hollow nanostructure. The photocatalytic performance sensitively depends upon content of amorphous carbon. Too much or too little carbon content decreases sample performance. The changes in performance according to carbon content are probably a result of the competing mechanism: the increasing rate of separation efficiency of photogenerated carriers and the decreasing contact area of ZnO with RhB according to the carbon content. This work would help us to better understand the important roles of carbon content in the fabricated nano-heterojunctions and also provide us with a feasible route to improve UV photocatalytic activities of ZnO and other metal oxides greatly.
025002
Xiaoyu Ma, Yongjia Liu and Bangshang Zhu
Strontium shows an increasing interest on bone formation and bone resorption prevention. Here, pure apatite strontium (Ap-SrOH) [Sr5(PO4)3(OH), strontium hydroxyapatite] particles were prepared by the precipitation method using Sr(NO3)2 · 6H2O and (NH4)2HPO4 as reagents. Scanning electron microscope, transmission electron microscope combined with electron diffraction, X-ray diffraction, Fourier transform infrared spectra (FTIR), variable temperature FTIR and thermo gravimetric analysis were employed to evaluate the crystalline structure, chemical composition, and thermal stability of the Ap-SrOH particles. The results show that phase pure Ap-SrOH particles were prepared by wet precipitation. The obtained Ap-SrOH particles are single crystal in phase structure, they have hexagonal fusiform shape, and their size is about 30–180 nm in diameter, and 0.4–2.5 μm in length. The cell MTT assay evaluations indicate that Ap-SrOH particles have very low cytotoxicity. Furthermore, nanoporous Ap-SrOH scaffolds were synthesized by anhydrous dextrose template method. After mixed 5–10 wt% of anhydrous dextrose with Ap-SrOH particles, pressed into discs, and sintered in microwave muffle furnace at 600 °C, the scaffolds with both nanoporous and nanotopography were formed. Cell culture of MC3T3-E1 osteoblasts in vitro show cells grow well on nanoporous Ap-SrOH scaffold. Therefore, Ap-SrOH particles and their nanoporous scaffolds are promising biomaterials for bone repairing and bone disease (e.g. osteoporosis) healing.
025003
Abraiz Khattak, Muhammad Amin, Muhammad Iqbal and Naveed Abbas
Micro and nanocomposites of ethylene propylene diene monomer (EPDM) are recently studied for different characteristics. Study on life estimation and effects of multiple stresses on its dielectric strength and backbone scission and oxidation is also vital for endorsement of these composites for high voltage insulation and other outdoor applications. In order to achieve these goals, unfilled EPDM and its micro and nanocomposites are prepared at 23 phr micro silica and 6 phr nanosilica loadings respectively. Prepared samples are energized at 2.5 kV AC voltage and subjected for a long time to heat, ultraviolet radiation, acid rain, humidity and salt fog in accelerated manner in laboratory. Dielectric strength, leakage current and intensity of saturated backbone and carbonyl group are periodically measured. Loss in dielectric strength, increase in leakage current and backbone degradation and oxidation were observed in all samples. These effects were least in the case of EPDM nanocomposite. The nanocomposite sample also demonstrated longest shelf life.
025004
Najmeh Moazeni, Morteza Vadood, Dariush Semnani and Hossein Hasani
The common bile duct is one of the body’s most sensitive organs and a polyurethane nanofiber tube can be used as a prosthetic of the common bile duct. The compliance is one of the most important properties of prosthetic which should be adequately compliant as long as possible to keep the behavioral integrity of prosthetic. In the present paper, the prosthetic compliance was measured and modeled using regression method and artificial neural network (ANN) based on the electrospinning process parameters such as polymer concentration, voltage, tip-to-collector distance and flow rate. Whereas, the ANN model contains different parameters affecting on the prediction accuracy directly, the genetic algorithm (GA) was used to optimize the ANN parameters. Finally, it was observed that the optimized ANN model by GA can predict the compliance with high accuracy (mean absolute percentage error = 8.57%). Moreover, the contribution of variables on the compliance was investigated through relative importance analysis and the optimum values of parameters for ideal compliance were determined.
025005
Hai-Dong Liu, Bin Gu, Wei-Feng Yuan and Qi He
A new polyurethane foam with superhydrophobicity and excellent lipophilicity is presented and demonstrated experimentally in this work. The superhydrophobic foam is synthesized by dip coating the polyurethane foam with a mixture solution of silicone resine and silicon dioxide nanoparticles. Its superhydrophobic and oleophilic capacity is characterized and verified via the SEM images, the water contact angle measurement, the adsorption tests and recyclability tests for water and some typical oils. Combining with the vacuum assisted oil-water separation technology (VAST), continuous recovery of oil spill at the lab scale is realized on the new superhydrophobic foam. Moreover, the break through pressure for water penetrating through the superhydrophobic foam is determined experimentally and referred as the maximum operation pressure in the VAST.
025006
Ding-Chao He, Qiu-Ming Fu, Zhi-Bin Ma, Hong-Yang Zhao, Ya-Fang Tu, Yu Tian, Di Zhou, Guang Zheng and Hong-Bing Lu
ZnO/zinc titanate core–shell nanorod arrays (CSNRs) were successfully prepared via a simple synthesis process by combining hydrothermal synthesis and liquid phase deposition (LPD). The surface morphologies, crystalline characteristics, optical properties and surface electronic states of the ZnO/zinc titanate CSNRs were characterized by scanning electron microscope, transmission electron microscope, x-ray diffractometer, x-ray photoelectron spectroscopy, PL and ultraviolet (UV)–visible absorption spectra. By controlling the reaction time of LPD, the shell thickness could vary with the reaction time. Furthermore, the impacts of the reaction time and post-annealing temperature on the crystalline structure and chemical composition of the CSNRs were also investigated. The studies of photocatalytic activity under UV light irradiation revealed that the ZnO/zinc titanate CSNRs annealed at 700 °C with 30 min deposition exhibited the best photocatalytic activity and good stability for degradation of methylene blue. It had been found that the effective separation of photogenerated electron–hole pairs in the CSNRs led to the enhanced photocatalytic activity. Moreover, the ZnO/zinc titanate CSNRs grown on quartz glass substrate could be easily recycled for reuse with almost unchanged photocatalytic activity.
025007
Kishore Kumar Nair, Rajesh Kumar, Madhuban Gopal and Weqar A Siddiqui
The study deals with the facile synthesis of catenated nanosulfur by entrapping elemental sulfur with polyethylene glycol 400 with the help of bottom up approach. The synthesized nanosulfur was studied by transmission electron microscope (TEM), x-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy and thermogravimetric analysis (TGA). The average size was about 35.5 ± 8.5 nm which was confirmed by TEM distribution curve fitted with Gaussian model. XRD shows that the synthesized nanosulfur was crystalline in nature. FTIR study confirmed that PEG was encapsulated over catenated nanosulfur. TGA confirmed the stability of nanosulfur up to 200 °C as there was no significant change in the differential weight with respect to temperature 200 °C. The active ingredient of this encapsulated nanosulfur was 0.62 g/g which was estimated by UHPLC.
025008
Mohammad Reza Barati
Nonlocal and surface effects on nonlinear vibration characteristics of a flexoelectric nanobeams under magnetic field are examined. Eringen’s nonlocal elasticity as well as surface elasticity theories are employed to describe the size-dependency of the flexoelectric nanobeam. Also, flexoelectricity is an important size-dependent phenomena for piezoelectric structures at nanoscale, related to the strain gradient-electric polarization coupling. After the derivation of governing equation via Hamilton’s principle, Galerkin method is employed to satisfy boundary conditions. Also, analytical procedures are implemented to obtain the closed-form nonlinear frequency of flexoelectric nanobeam. It is showed that magnetic field intensity, flexoelectric parameter, nonlocal parameter, elastic foundation and applied voltage on the top surface of the nanobeam have great influences on nonlinear vibration frequency.
025009
Boni Samuel, S Mathew, V R Anand, Adrine Antony Correya, V P N Nampoori and A Mujeeb
This paper reports, broadband photoluminescence from CdSe quantum dots (QDs) under the excitation of 403 nm using fluorimeter and 403 nm CW laser excitation. The broad spectrum obtained from the colloidal quantum dots was ranges from 450 nm to 800 nm. The broadness of the spectra was attributed to the merging of band edge and defect driven emissions from the QDs. Six different sizes of particles were prepared via kinetic growth method by using CdO and elemental Se as sources of Cd and Se respectively. The particle sizes were measured from TEM images. The size dependent effect on broad emission was also studied and the defect state emission was found to be predominant in very small QDs. The defect driven emission was also observed to be redshifted, similar to the band edge emission, due to quantum confinement effect. The emission corresponding to different laser power was also studied and a linear relation was obtained. In order to study the colour characteristics of the emission, CIE chromaticity coordinate, CRI and CCT of the prepared samples were measured. It is observed that, these values were tunable by the addition of suitable intensity of blue light from the excitation source to yield white light of various colour temperatures. The broad photoluminescence spectrum of the QDs, were compared with that of a commercially available white LED. It was found that the prepared QDs are good alternatives for the phosphor in phosphor converted white LEDs, to provide good spectral tunability.
025010
The following article is Open access
Filippo S Boi, Xiaotian Zhang and Anna Corrias
We report the observation of novel temperature-driven structural-memory-effects in carbon nanotubes (CNTs) filled with Fe3C nano-crystals. These structural-transitions were measured by means of temperature (T) dependent x-ray diffraction (XRD) in the T-range from 298 K to 12 K. A clear reversible 2θ-shift in the 002-peak of the graphitic-CNTs-walls is found with the decrease of the temperature. As determined by Rietveld refinement, such 2θ-shift translates in a not previously reported decrease in the value of the CNT graphitic c-axis with the decrease of the temperature (from 298 K to 12 K). Also, a clear reversible 2θ-shift in the 031 and 131 diffraction-peaks of Fe3C is observed within the same T-range. Rietveld refinements confirm the existence of such memory-effect and also reveal a gradual decrease of the 010-axis of Fe3C with the decrease of the temperature. These observations imply that the observed structural-memory-effect is a characteristic of CNTs when Fe3C is the encapsulated ferromagnet. The generality of such memory-effects was further confirmed by additional measurements performed on other types of CNTs characterized by continuous Fe3C-filling. XRD measurements in the T-range from 298 K to 673 K revealed also an unusual reversible decrease of the Fe3C-peak intensities with the increase of the temperature. These observations can have important implications on the magnetic data recording applications of these nanostructures by helping in better understanding the unusual temperature-dependent magnetic instabilities of iron-based nano-crystals which have been recently reported in literature.
025011
T Chandrakalavathi, Koteswara Rao Peta and R Jeyalakshmi
In this work, we demonstrated Au nanoparticles incorporated reduced graphene oxide (rGO)/Si heterostructure based UV photodetector. The pristine and Au nanoparticles incorporated heterostructure was analyzed and characterized by x-ray photo electron spectroscopy (XPS), Current- Voltage (I-V) characteristics and UV photo detective properties were examined by using UV light emitting diode (LED) with 382 nm wavelengths. The UV photoresponse properties revealed that the Au-rGO/Si heterostructure showed much better photoresponse activity toward UV light than pristine rGO/Si. The experimental results clearly revealed that the photoresponse of Au-rGO/Si heterostructure can be effectively enhanced by 30 times at 382 nm wavelength over pristine rGO/Si. The effect of rGO thickness on performance of UV photodetector was also examined. The improved photoresponse was attributed to localized surface plasmon resonance, in addition high electron transport capability of rGO number of photoexcited electrons collected at interface.
025012
Ying Zhang, Yiping Huo, Nini Cai, Yuhai Li and Chen Zhou
Surface plasmon resonances (SPRs) of the nonconcentric asymmetric ring-ring nanostructure have been researched by using finite element method. In this plasmonic system, higher order magnetic Fano resonances are achieved. It is demonstrated that the magnetic Fano resonances originate from the coupling between the bright electric and the dark magnetic modes. The electric and magnetic resonances can be adjusted by the offset of the cavity, the width of the outer ring, the magnification times of the structure and the offset of the inner ring. The nanostructure allows the generation of multiple magnetic Fano resonances and strong magnetic field enhancement which can make the proposed nanostructure highly suitable for the plasmons propagation with low-loss magnetic, multi-wavelength surface enhanced spectroscopy and Fano switch.
025013
Cuilian Wen, Xinyuan Zhang, Ying Wei, Teng Zhang and Changxin Chen
A facile self-assembly approach is reported to prepare palladium/carbon nanotubes (Pd/CNTs) catalyst for the electro-oxidation of ethanol. In this method, the Pd-oleate/CNTs was decomposed into the Pd/CNTs at an optimal temperature of 195 °C in air, in which no inert gas is needed for the thermal decomposition process due to the low temperature used and the decomposed products are also environmental friendly. The prepared Pd/CNTs catalyst has a high metallic Pd0 content and the Pd particles in the catalyst are disperse, uniform-sized with an average size of ∼2.1 nm, and evenly distributed on the CNTs. By employing our strategy, the problems including the exfoliation of the metal particles from the CNTs and the aggregation of the metal particles can be solved. Comparing with the commercial Pd/C one, the prepared Pd/CNTs catalyst exhibits a much higher electrochemical activity and stability for the electro-oxidation of ethanol in the direct ethanol fuel cells.
025014
Chunxu Liu, Jisen Zhang, Yongyi Chen, Pengtao Jing, Ligong Zhang, Haifeng Zhao, Xihong Fu and Lijun Wang
Photoluminescence (PL) and time-resolved spectroscopic studies on plasmonically coupled semiconductor nanoparticles (SNPs) have demonstrated the PL quenched and lifetime enhanced of SNPs in the presence of metal nanoparticles (MNPs). The hybrid colloidal CsPbBr3 perovskite SNPs/Pt MNPs (S-M) structures exhibit novel optical properties due to the synergetic interaction between the individual components. In hybrid S-M nanostructures colloidal chemistry incorporates SNP and MNP into a single unit resulting in the formation of plexciton (or excimon) which has now been established in a series of hybrid structures. The experimental results of femtosecond transient absorption (TA) spectroscopy based on the time-resolved pump−probe confirm the transformation from excitons to plexcitons. It was found that the experimental data can’t be well described by the theory based on conventional Fӧster resonance energy transfer (FRET). The differences between theory and experiment may be due to the missing some PbBr2 PL peaks, the reason will be revealed further.
025015
Ishtiaque Ahmed Navid, Asir Intisar Khan and Samia Subrina
The thermal conductivity of single layer strained hexagonal boron nitride nanoribbon (h-BNNR) has been computed using the Green—Kubo formulation of Equilibrium Molecular Dynamics (EMD) simulation. We have investigated the impact of strain on thermal transport of h-BNNR by varying the applied tensile strain from 1% upto 5% through uniaxial loading. The thermal conductivity of h-BNNR decreases monotonically with the increase of uniaxial tensile strain keeping the sample size and temperature constant. The thermal conductivity can be reduced upto 86% for an applied uniaxial tensile strain of 5%. The impact of temperature and width variation on the thermal conductivity of h-BNNR has also been studied under different uniaxial tensile strain conditions. With the increase in temperature, the thermal conductivity of strained h-BNNR exhibits a decaying characteristics whereas it shows an opposite pattern with the increasing width. Such study would provide a good insight on the strain tunable thermal transport for the potential device application of boron nitride nanostructures.
025016
Javad Vahabzadeh Pasikhani, Neda Gilani and Azadeh Ebrahimian Pirbazari
Freestanding TiO2 nanotubes (FSNTs) with various physical dimensions were fabricated by two-step anodization process with different voltages and anodization times. The detachment method employed in this study involved voltage reduction at the end of the second step and ultrasonic chemical treatment. The results demonstrated that this detachment method is a beneficial technique to create thin open-mouthed and closed-end FSNTs (with lengths of 6–14 μm). Moreover, the influences of anodization conditions on photocatalytic activity, structural properties and geometrical features of FSNTs in comparative degradation of two non-colored (2,4-dichlorophenol) and colored (methylene blue) pollutants were investigated. Findings revealed that the quantity of the photocatalyst utilized is an effective parameter and using the optimum weight (10 mg/100 ml of 2,4-dichlorophenol) could increase the efficiency of the process up to 21%. Further, the results demonstrated that if equal optimum weights of FSNTs are chosen, decreases in voltage and anodization time significantly influence the structural properties, geometrical features, and photodegradation efficiency. The enhancement achieved in the degradation of both 2,4-dichlorophenol and methylene blue using the nanotubes with the shortest diameter (54 nm) and length (6.5 μm), which possess the lowest porosity (0.5) and also the highest surface area (0.53 m2 g−1), nanotubes’ density (19 cm2 cm−2) and wall thickness to length ratio (2). In addition, the results obtained indicated that the degradation reactions follow first-order kinetics in the degradation of the both pollutants. The apparent degradation rate constant of methylene blue was approximately 1.2 times greater than of the 2,4-dichlorophenol due to the negative charge of the nanotubes’ surface and electrostatic adsorptions.
025017
Raid A Ismail, Walid K Hamoudi and Hadeel F Abbas
The synthesis of cadmium sulfide CdS nanowires NWs by laser ablation of cadmium target in thiourea solution is demonstrated for the first time. The effect of laser fluence on the structural, morphological and optical properties of CdS nanoparticles was investigated. The synthesized CdS nanowires were polycrystalline with pure hexagonal wurtzite phase; as confirmed by x-ray powder diffraction results. The 3.18–3.26 eV direct optical energy gap of CdS and the increase of CdS optical absorption were noticed to be function of laser fluence. The results revealed a blue shift of 0.86 eV in the absorption edge of CdS nanowires when prepared at 2.65 J cm−2. The infrared absorption spectra revealed the presence of Cd-S stretching vibration peak located at (525–700) cm−1. Raman spectra confirmed the presence of a sharp peak at 304 cm−1 with intensity increased at higher values of laser fluence. Photoluminescence at room temperature indicated an emission peak of CdS at 471 nm. The scanning electron microscopy SEM investigation of the synthesized CdS showed a mixture of hexagonal nanoparticles and nanowires arrays. Transmission electron microscopy TEM investigation revealed the formation of well-dispersed single CdS nanowires with diameter in the range (18–27) and tens of micrometers long. The effect of laser fluence on the performance of n-CdS NWs/p-Si heterojunction was investigated.
025018
W Fortas, A Djelad, M A Hasnaoui, M Sassi and A Bengueddach
In this work, AlPO-34, like-chabazite (CHA) zeolite, was ionothermally prepared using the ionic liquid (IL), 1-ethyl-3-methylimidazolium chloride [EMIMCl], as solvent. The solids obtained were characterized by x-ray powder diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (FTIR), thermal analysis (TG) and nitrogen adsorption/desorption at 77.3 K. The results show that the ionic liquid is occluded in the AlPO-34 framework and consequently it acts also as a structure-directing agent. The variation of chemical composition led to AlPO-34 materials with different crystal sizes and morphologies. The well crystallized AlPO-34 material was used as adsorbent for Crystal Violet (CV) dye removal from aqueous solutions. The effect of adsorption parameters such as pH and initial concentration were investigated. It was found that adsorption dyes is favorable at pH = 6. The adsorption isotherm data follow the Langmuir equation in which parameters are calculated. The selected AlPO-34 sample exhibited a high crystal violet dye removal of 46.08 mg g−1 at pH = 6.
025019
Seyed Mostafa Rahimian-Koloor, Hadi Moshrefzadeh-Sani, Mahmood Mehrdad Shokrieh and Seyed Majid Hashemianzadeh
In the classical micro-mechanical method, the moduli of the reinforcement and the matrix are used to predict the stiffness of composites. However, using the classical micro-mechanical method to predict the stiffness of CNT/epoxy nanocomposites leads to overestimated results. One of the main reasons for this overestimation is using the stiffness of the isolated CNT and ignoring the CNT nanoscale effect by the method. In the present study the non-equilibrium molecular dynamics simulation was used to consider the influence of CNT length on the stiffness of the nanocomposites through the isothermal-isobaric ensemble. The results indicated that, due to the nanoscale effects, the reinforcing efficiency of the embedded CNT is not constant and decreases with decreasing its length. Based on the results, a relationship was derived, which predicts the effective stiffness of an embedded CNT in terms of its length. It was shown that using this relationship leads to predict more accurate elastic modulus of nanocomposite, which was validated by some experimental counterparts.
025020
Subburaman Chandramohan, Krishnan Sundar and Azhaguchamy Muthukumaran
Selenium is one of the essential elements involved in antioxidative and antiinflammatory effects in human body. By naturally, selenium ions are metabolised and converted into nano selenium. Now a days there is an increasing attention on applications of nanoparticles in therapeutic field. In the present study Bacillus subtilis was used to convert sodium selenite to SeNPs. The synthesized SeNPs were characterized by Fourier Transform Infrared Spectroscopy (FTIR), X Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) coupled with Energy Dispersive X ray spectroscopy (EDX). The presence of SeNPs was confirmed by the formation of red colour. The bands were sharp with broad absorption peaks at 3562 cm−1 and 1678−1 cm in FTIR which showed that the bacterial proteins were responsible for the reduction of sodium selenite to SeNPs. The average size of the SeNPs was 334 nm and were spherical in shape with uniform distribution. The XRD data confirmed that SeNPs were of amorphous in nature. The zeta potential of SeNPs was negative in charge which indicated high stability. In the present study zebrafish embryos were used to study the toxicity of SeNPs and the results showed that the concentration beyond 10 μg ml−1 leads to toxic effects in embryos/hatchlings. The lesser concentration of SeNPs can be useful in various biomedical applications.
025021
Zhenxiang Liu, Weicheng Jiao, Meiling Yan, Jun Li, Guomin Ding and Rongguo Wang
The way gas molecules penetrate the resin matrix composites are generally divided into diffusion penetration and destruction penetration. Through theoretical analysis, the larger the nanoscale layers, the smaller the penetration effect in the directional nanosheets reinforced resin matrix composites. To control destruction penetration, the cracks should be reduced by toughening resin matrix composites. In order to solve these two kinds of leakage, the magnetic graphene oxide is connected to mimic nacre while L- glutamic acid is used as binder and the directional solidification is also utilized. Compared with pure resin, only 0.13 wt% monolithic magnetic graphene oxide and its interbed reinforced composites can reduce the leakage of He by 36.4% and 52.0% respectively, and the toughness of composites is validated to increase 4.0% and 20.3% respectively. This toughening mechanism is similar to that of nacre.
025022
Liwei Yu, Chunyan Du and Xiaojie Liu
Dy adatom adsorption and penetration on defected graphene were studied using first-principles calculations. We show that adsorption of Dy adatom on defect is energetically more favorable than on pristine graphene. Strong covalent bonding between Dy and C atoms at the defect sites is confirmed by interaction charge density analysis. We also found that the pathways for Dy penetration through defects with 1 and 2 missing carbon atoms are different from those through larger holes in graphene due to strong spatial confinement effects. The larger size of the hole is, the smaller barrier for Dy penetration.
025023
Ying Zhang, Gaurab Rimal, Jinke Tang and Qilin Dai
Magnetic nanoparticles are of great interest due to their applications in energy and environment. In this work, we developed a chemical solution based method to synthesize NiFe2O4 (NFO) nanoparticles with different sizes and structures by organic ligands and studied their applications in magnetic electrolyte concentration cells and waste water treatment. NFO nanoparticle growth is controlled by the organic passivating ligand ratios, reaction temperatures, and reaction solution concentrations to achieve the control of NFO nanoparticle size ranging from 25 nm to 160 nm. The NFO growth mechanism is controlled by aggregation related mechanism, leading to tunable magnetic properties and concentration cell device performance. Magnetic biochar consisting of biochar/NFO composite was also obtained based on the developed method. Waste water containing Rhodamine B was tested by the synthesized magnetic biochar. We believe the method developed in this work about magnetic NFO nanoparticles and magnetic biochar will shed light on the application of magnetic nanoparticles in energy and environment.
025024
Tiejun Zhao, Xiaojie Li, John H S Lee and Honghao Yan
Using ferrocene, H2 and O2, Carbon nanomaterials were prepared with gaseous detonation (deflagration) method. The effects of H2 on the phase and morphology of carbon nanomaterials were studied by various proportions of H2 in the reaction. The prepared samples were characterized by x-ray diffractometer, transmission electron microscope and Raman spectrometer. The results show that hydrogen proportion has a great influence on the phase and morphology of carbon nanomaterials. The high hydrogen proportion leads to much unreacted hydrogen, which could protect the iron atom from oxidation of carbon and dilute the reactants contributing to uniform particle size. In addition, the graphitization degree of multi-walled carbon nanotubes, observed in samples with high H2 proportion, is high enough to see the lattice fringes, but the degree of graphitization of whole sample is lower than which fabricated with low H2 proportion, and it may result from the low energy generation.
025025
Adel M El Sayed
Controlling the properties of nano-sized hematite (α-Fe2O3) is an interesting approach for broadening its multifunctionality and applications. This work presents the effect of the oxalic acid molar ratio from 0.0 to 2.0 and the annealing in the range 350–950 °C, on the physical properties of hematite nanopowder prepared by simple chemical solution and evaporation. The microstructural analysis was performed by XRD, HR-TEM and FTIR. Both XRD and FTIR spectroscopy proved the presence of hematite rhombohedral structure as the sole detectable phase. Increasing the oxalic acid molar ratio decreased the crystallite size (Cs), converted the nanorods (NRs) morphology to nanoparticles (NPs) and blue-shifted the optical band gap (Eg). However, increasing the annealing temperature (TA) increased the Cs value from 50.63 nm to 87.93 nm, improved the NRs growth, and red-shifted Eg from 2.35 eV to 2.20 eV. The influence of these two preparative parameters on the lattice parameters, the dielectric constant and the AC conductivity of the prepared hematite nanopowders are also discussed.
025026
Mohammadreza Soltani and Amir Atrian
This paper investigates the high-temperature tensile behavior of Al-SiC nanocomposite reinforced with 0, 1.5, and 3 vol% SiC nano particles. To fabricate the samples, SiC nano reinforcements and aluminum (Al) powders were milled using an attritor milling and then were cold pressed and hot extruded at 500 °C. Afterward, mechanical and microstructural characteristics were studied in different temperatures. To this end, tensile and compressive tests, micro-hardness test, microscopic examinations, and XRD analysis were performed. The results showed significant improvement of mechanical properties of Al-SiC nanocomposite in room temperature including 40% of ultimate tensile strength (UTS), 36% of ultimate compressive strength (UCS), and 44% of micro-hardness. Moreover, performing tensile tests at elevated temperatures (up to 270 °C) decreased the tensile strength by about 53%, 46%, and 45% for Al-0 vol% SiC, Al-1.5 vol% SiC, and Al-3 vol% SiC, respectively. This temperature rise also enhanced the elongation by about 11% and 133% for non-reinforced Al and Al-3 vol% SiC, respectively.
025027
S A Sabinas-Hernández, A Romero-Núñez and G Díaz
The effect of plasmonic excitation of Ag/SiO2 catalysts was studied in the preferential CO oxidation in presence of H2 (PROX) at low temperature. Catalysts with 5 wt% silver loading were prepared by wet impregnation in aqueous and basic media. TEM analysis indicates the presence of Ag nanoparticles with a broad particle size distribution which can achieve both, good PROX activity at low temperature and plasmonic interaction with visible light. Photo-assisted reaction at 35 °C enhance CO and O2 conversions; however, the greater improvement was found for O2 conversion. The selectivity towards CO2 decrease when reaction took place under photo-thermal conditions. Occurrence of different silver species and particle size changed after reaction as evidenced by DRS-UV–vis and TEM.
025028
Gang Chen, ChuanJie Wang, Ying Zhang and Peng Zhang
The size-dependent plastic deformation and fracture mechanism of Cu/Ag bi-metal nano-pillar with multilayer structure are investigated by atomistic simulation. The results show that the relative rotation of adjacent Cu and Ag layer plays an important role for twin process of NP with big diameter. Due to the different orientations of adjacent Cu and Ag layers, the deformation twin can be formed by decomposition of the leading dislocation. This kind of deformation will form a bend interface between Cu and Ag layers. The tilt part of bend interface induces to interface sliding.
025029
Mahreen Akram, Shazia Bashir, Sohail Abdul Jalil, Muhammad Shahid Rafique, Asma Hayat and Khaliq Mahmood
The effect of Nd:YAG (1064 nm, 10 ns, 10 Hz) laser induced surface structuring of copper (Cu) for enhancement of field emission (FE) properties has been investigated. X-ray diffraction analysis was employed to investigate the surface structural and compositional modifications. The surface structuring was explored by scanning electron microscope investigation. FE properties were studied under UHV conditions in a parallel plate configuration of planar un-irradiated Cu anode and laser irradiated Cu cathode. The Fowler–Nordheim plots were drawn to confirm the dominance of FE behavior of the measured I–V characteristics. The obtained values of turn-on field ‘Eo’, field enhancement factor ‘β’ and maximum current density ‘Jmax’ come out to be to be in the range of 5.5–8.5 V μm−1, 1380–2730 and 147–375 μA cm−2 respectively for the Cu samples irradiated at laser irradiance ranging from 13 to 50 GW cm−2. The observed enhancement in the FE properties has been correlated with the growth of various surface structures such as ridged protrusions, cones and pores/tiny holes. The porous morphology is found to be responsible for a significant enhancement in the FE parameters.
025030
Astakala Anil Kumar, Ashok Kumar and J K Quamara
In present study, we report dielectric, ferroelectric and pyroelectric behavior of pristine and La3+ containing barium stannate nanoparticles synthesized via wet chemical route involving cetyltriammonium bromide assisted thermal decomposition of binary precursors. The X-ray diffraction patterns of pristine and La3+ (2, 4 and 6 at%) doped BaSnO3 nanoparticles showed the formation of cubic perovskite phase. On substitution of Ba2+ lattice sites by La3+ at the La content of 6 at%, the sample exhibited fourfold increase in conductivity in comparison to pristine BaSnO3. Polarization hysteresis (P-E) curves of La containing barium stannate nanoparticles showed anti-ferroelectric behavior. The pyroelectric coefficient of pristine and La (2, 4 and 6 at%) containing BaSnO3 nanoparticles at 473 K were found to be 7.8, 11.6, 14.1 and 17.2 μCm−2K−1, respectively. Further, the responsivity and detectivity values were higher in comparison to the materials, such as AlN, GaN, CdS and ZnO.
025031
Sudha Kumari and Rakesh S Moirangthem
This work illustrates a label-free sensing of biomolecules using a simple capillary sensor. Here, capillary biosensor was prepared by decorating inner walls of a glass capillary with gold nanoparticles that was employed to investigate the biomolecular interactions. As a demonstration, rabbit immunoglobulin G (IgG) and anti-rabbit IgG (anti-IgG) proteins were chosen as a model system to monitor the receptor-analyte interactions. A surface binding sensitivity of 409 pg mm−2 was able to achieve towards the detection of 10 nM concentration of anti-rabbit IgG. The presented plasmonic sensor provides multiple advantages over conventional LSPR sensor by lifting requirement of the flow cell, prolonged sample preparation, complicated measurement setup etc that may enable its usage in rapid diagnostic testing. We believed that our proposed plasmonic capillary sensor could represent a potential candidate for developing cost-effective, label-free and high sensitivity sensing device for detection of biological molecules at low concentration.
025032
B Prakash, S Asha, A Nimrodh Ananth, G Vanithakumari, G S Okram, Sujin P Jose and M A Jothi Rajan
Chitosan/tripolyphosphate polyelectrolyte (TPP) microspheres, decorated and surface functionalized with silver nanoparticles (NPs) of average diameter of 15 nm, were synthesized following a simple two-step procedure. These Ag NP-functionalized polyelectrolyte microspheres (Ag-CSPMs) are found to be biocompatible and enhancing the reactive oxygen species in curcumin with excellent anti-bacterial activity for selected Gram-positive and negative bacterial strains, making them much attractive relative to bare surface counterparts; the well-stabilized silver NPs do not form any agglomerations on the surface of the chitosan microspheres. They also show excellent cytotoxic behavior towards MCF7 cell lines, showing a half-maximal inhibitory concentration (IC50) of 32 μg ml−1. Therefore, Ag-CSPMs exhibit multi-functional ability having potential towards theranostics applications.
025033
Afaf El-Ansary, Arjumand Warsy, Maha Daghestani, Nada M Merghani, Abeer Al-Dbass, Wadha Bukhari, Badryah Al-Ojayan, Eiman M Ibrahim, Asma M Al-Qahtani and Ramesa Shafi Bhat
The current study aims to synthesize silver nanoparticles using Ziziphus spina Christi (ZSC) or (Sidr) aqueous leaf extract collected from Riyadh, Saudi Arabia. The green synthesis of silver nanoparticles using sidr leaves extract was successful. Production of silver nanoparticles was confirmed through UV–vis Spectrophotometer, particles size and zeta potential analysis, Infra-red spectroscopy, Scanning, and Transmission Electron Microscope (SEM and TEM). The UV–visible spectra showed that the absorption peak existed at 400 nm. SEM analysis showed that the synthesized AgNPs were spherical but in slightly aggregated form. TEM demonstrated different size range of 4–33 nm with an average size of 13. The element analysis profile showed silver signal together with oxygen, calcium, and potassium peaks which might be related to the plant structure. Biological effects of the synthesized AgNPs exhibit satisfactory inhibitory effect against ten tested microorganisms. It inhibited the growth of 5 gram-positive and five gram-negative bacteria. Moreover, AgNPs demonstrated a synergistic effect on the neurotoxicity induced in rat pups with orally administered methyl mercury (MeHg). The present study showed that AgNPs prepared from ZSC might be a promising antimicrobial agent for successful treatment of bacterial infection in intensive care units (ICU) especially in case of antibiotic resistance.
025034
Jinsong Hu, Xinhua Huang, Nuoya Wang and Lei Zhang
A new molecule 3-[2-(7-oxa-bicyclo[4.1.0]hept-3-yl)-ethylsulfanyl]-propane-1,2-diol (CESPO) was synthesized by click reactions. The molecule has hydroxyl and thioether groups which could thus chelate with active cations. Through a sol-gel process, we thus fabricated porous nano-TiO2 in the presence of CESPO. The prepared TiO2 having high specific surface area and was composed of nanocrystals which are favorable for effective charge transport as photocatalyst carrier. On the other hand, Ag nanoparticles were loaded on TiO2 composites that could be utilized as photocatalyst for degradation of RhB. The experimental results exhibit plasmon enhanced photocatalytic activity depending on the loading amount of the AgNPs. This work provides a facile method to prepare porous oxides that could be adapted for catalyst carriers.
025035
Rajender Singh, Karan Verma, Tejbir Singh, P B Barman and Dheeraj Sharma
Development of ultraviolet (UV) shielding with visible transparency based thermoplastic polymer nanocomposite (PNs) presents an important requisite in terms of their efficiency and cost. Present study contributed for the same approach by dispersion of Ag doped ZnO nanoparticles upto 10 wt% in poly (styrene-co-acrylonitrile) matrix by insitu emulsion polymerization method. The crystal and chemical structure of PNs has been analyzed by x-ray diffraction (XRD) and fourier infrared spectrometer (FTIR) techniques. The morphological and elemental information of synthesized nanomaterial has been studied by field emission scanning electron microscope (FESEM) and energy dispersive spectroscopy (EDS) technique. The optical properties of PNs has been studied by UV–visible spectroscopy technique. The incorporation of nanoparticles in polymer matrix absorb the complete UV light with visible transparency. The present reported polymer nanocomposite (PNs) have tuned refractive index with UV blocking and visible transparency based properties which can serve as a viable alternative as compared to related conventional materials.
025036
Saisai Zhang, Zhengqi Zhang, Jianzhong Pei, Rui Li, Jiupeng Zhang, Jun Cai and Jiexue Cui
In this paper, a novel TiO2-SiO2 aerogel nanocomposite absorbent was successfully synthesized using the sol-gel and ambient pressure drying method, and its photocatalytic degradation effects on automobile exhaust were investigated for the first time. The microstructures and properties of the Nano TiO2-SiO2 aerogels were characterized using various methods, including x-ray Diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area analysis, Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and Fourier Transform Infrared Spectroscopy (FT-IR). The exhaust purification tests were conducted in a self-developed instrument to investigate the degradation effects of Nano TiO2-SiO2 aerogels on automobile exhaust through degradation rate. Experimental results showed that the Nano TiO2-SiO2 aerogels had a good photocatalytic degradation effect on automobile exhaust, and the degradation rates of CO, CO2, HC and NOx were 1.3%, 1.5%, 3.2% and 34.4%, respectively. The well-designed microstructure makes the Nano TiO2-SiO2 aerogels a stable photocatalytic material with high specific surface area and big average pore size, which has promising applications in environmental treatment.
025037
Surbhi, Vikas Sharma, Satyavir Singh, Priyanka Garg, K Asokan and Kanupriya Sachdev
An investigation of MWCNT-based hybrid electrode films with improved electrical conductivity after Xe ion irradiation is reported. A multilayer hybrid structure of Ag-MWCNT layer embedded in between two ZnO layers was fabricated and evaluated, pre and post 100 keV Xe ion irradiation, for their performance as Transparent Conducting Electrode in terms of their optical and electrical properties. X-ray diffraction pattern exhibits highly c-axis oriented ZnO films with a small variation in lattice parameters with an increase in ion fluence. There is no significant change in the surface roughness of these films. Raman spectra were used to confirm the presence of CNT. The pristine multilayer films exhibit an average transmittance of ∼70% in the entire visible region and the transmittance increases with Xe ion fluence. A significant enhancement in electrical conductivity post-Xe ion irradiation viz from 1.14 × 10−7 Ω−1 cm−1 (pristine) to 7.04 × 103 Ω−1 cm−1 is seen which is due to the high connectivity in the top layer with Ag-CNT hybrid layer facilitating the smooth transfer of electrons.
025038
Ali Sadooghi and Gholamhassan Payganeh
Powder metallurgy process is one of the approaches to manufacture nanocomposite samples, in which the product quality depends upon the pressure, temperature, and sintering time. In this manuscript, steel is selected as the base material together with 2% carbon-based reinforcing TiC particles, and 2% hBN particles as the self-lubricant material. The powders were mixed for 5 h in high ball milling, and compacted with two pressures of 350 and 450 MPa, sintered in the furnace for 2 and 4 h, and sintering temperatures of 1350 and 1450 °C were utilized. SEM, XRD, and EDX tests are performed to identify the nanocomposite structure, and DTA tests are carried out to specify the temperature graph of the material. Finally, hardness, wear, and bending tests are done to find the corresponding mechanical properties of the samples. As a result, the optimum process parameters, including pressure, temperature and sintering duration is achieved. Results show that adding the reinforcing particles into a steel matrix increase the hardness, as well as flexural strength of the nanocomposite product. Also, coefficient of friction shows a decreases.
025039
Donghai Ding, Zipei Li, Guoqing Xiao and Shaoyu Yang
The bulk Si-O-C ceramics were prepared by polymer derived ceramics (PDCs) route using polysiloxane as precursor and their properties were investigated for electromagnetic wave absorbing in the frequency range of 12.4–18 GHz (Ku-band). It was found that the catalytic pyrolysis can enhance substantially the absorbing properties by in situ formation of turbostratic carbon network, ordered carbon, and multi-wall carbon nanotubes. The matching thickness of sample containing 1.5 wt% FeCl3 (FPSO-1.5) is 2.2 mm, and its reflection loss exceeds −10 dB in the whole Ku-band with an absorption peak of −35.48 dB at 14.16 GHz. For sample containing 1.5 wt% FeCl3, its absorption peak increases to −15.78 dB, but its matching thickness decreases significantly to 2.2 mm. The polymer derived Si-O-C ceramics could be used as excellent electromagnetic functional devices working in harsh environments.
025040
S Jagadhesan, N Senthilkumar, V Senthilnathan and T S Senthil
In the present work, simple co-precipitation approach for pure zinc oxide (ZnO) nanoparticles (NPs) and antimony (Sb) doped ZnO Nanostructures (NSs) has been investigated. The phase purity and various functional groups observed from the synthesized materials were confirmed by powder x-ray diffraction (PXRD) and Fourier Transform Infrared Spectroscopy (FTIR) studies. The surface morphology of the spherical like pure ZnO and cubic, hexagonal and net-like Sb (0.05%, 0.075%) doped ZnO NSs are observed by using Field Emission Scanning Electron Microscopy (FESEM) analysis and compositional elements which are presence in the synthesized particles were determined by Energy Dispersive x-ray spectroscopy (EDAX) analysis. The synthesized Sb (0.05% and 0.075%) doped with ZnO NSs acts as the catalyst for photocatalytic activity.
Organic materials
025101
Ashok Sharma, Dinesh Kumar, Prashant Uday Manohar, Surojit Pande, Anshuman Dalvi and Paritosh Shukla
Five substituted pyranopyrazole (PPZ) derivatives were chemically synthesized by conventional and microwave assisted synthesis (MWA) methodology. Their differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) analyses, and the corrosion inhibitor properties on mild copper metal in 1 M HCl solution were investigated by SEM (Scanning Electron Microscopy), EDS (Energy Dispersive Spectroscopy), and XRD (x-ray Diffraction) all of which showed good anti-corrosion behavior. Further, mechanical property investigations were also performed by measuring the tensile strength of the PPZ-adsorbed Cu-strips. Finally, the inhibition action was evaluated by quantum chemical parameters. All the experimental results pointed that the molecules acted as excellent anti-corrosion surface active agents for copper metal.
025102
Hongwei Lu, Liming Zou, Yongjing Xu, Hong Sun and Yan Vivian Li
A simple method of using wet spinning was found effective in the preparation of photoluminescent poly vinyl alcohol (PVA)/hyperbranched polylysine (HBPL) fibers. The photoluminescence of the PVA/HBPL fibers was significantly uniform and the unique uniformity was obtained by controlling the mass ratio of PVA to HBPL in aqueous solutions used in the wet spinning process. The high solubility of HBPL in water make it feasible to well control in the mass ratio of PVA to HBPL, which facilitated the formation of a unique PVA/HBPL mixture, resulting in the fabrication of homogeneous PVA composite fluorescence fibers. The composite fibers exhibit good mechanical, and thermal properties that make the PVA/HBPL fluorescent fibers a great material potentially used in fluorescence applications including optics, imaging and detection.
Glasses and amorphous materials
025201
Ting Wu, Shilong Zhao, Ruoshan Lei, Lihui Huang and Shiqing Xu
Er3+/Yb3+ codoped BaGdF5 glass ceramics have been prepared and used to develop a portable all-fiber temperature sensor based on fluorescence intensity ratio technique. XRD and TEM results affirm the generation of BaGdF5 nanocrystals in the borosilicate glass. Eu3+ ions are used as spectral probe to investigate external environment around rare earth (RE) ions. Intense green upconversion emissions from Er3+ ions are detected in the BaGdF5 glass ceramics and their intensity are enhanced about three orders of magnitude after heat treatment, which is attributed to the enrichment of RE ions in the BaGdF5 phase. Based on green upconversion emission from Er3+ ions, the temperature sensing property of the portable all-fiber temperature sensor is studied. The maximum absolute sensitivity is 15.5 × 10−4 K−1 at 567 K and the relative sensitivity is 1.28% K−1 at 298 K, respectively.
025202
P P Zhou, G Q Wu, Y Tao, X Cheng, J Q Zhao and H Nan
A series of calcium-based ceramic cores for casting titanium alloy were prepared by mixing different amounts of coarse and fine powders through injection molding. The effects of particle size on the microstructures and properties of the ceramic cores were investigated using quantitative and statistical analysis methods. It is found that the shrinkage and room-temperature strength of the ceramic cores were enhanced as increasing the contents of fine particles. Moreover, the creep resistance of the ceramic cores increased initially and then decreased. The increase in the fine particle content of the cores reduced the number and mean diameter of pores after sintering. The grain boundary density decreased firstly and then increased. The flexural strength of the ceramic cores at room temperature decreased with increasing porosity of ceramic cores, whereas the creep resistance increased with decreasing grain boundary density. A core exhibiting the optimal property was obtained when mixing 65 wt% of coarse powders (75–150 μm) and 35 wt% of fine powders (25–48 μm).
025203
A N Upadhyay, R S Tiwari and Kedar Singh
This study deals with the effect of thermal annealing on structural/microstructural, thermal and mechanical behavior of pristine Se80Te16Cu4 and carbon nanotubes (CNTs) containing Se80Te16Cu4 glassy composites. Pristine Se80Te16Cu4, 3 and 5 wt%CNTs-Se80Te16Cu4 glassy composites are annealed in the vicinity of glass transition temperature to onset crystallization temperature (340–380 K). X-ray diffraction (XRD) pattern revealed formation of polycrystalline phases of hexagonal CuSe and trigonal selenium. The indexed d-values in XRD patterns are in well conformity with the d-values obtained after the indexing of the ring pattern of selected area electron diffraction pattern of TEM images. The SEM investigation exhibited that the grain size of the CNTs containing Se80Te16Cu4 glassy composites increased with increasing annealing temperature and decreased at further higher annealing temperature. Thermal conductivity, microhardness exhibited a substantial increase with increasing annealing temperature of 340–360 K and slightly decreases for 380 K. The variation of thermal conductivity and microhardness can be explained by cross-linking formation and voids reduction.
025204
Changdong Ma, Fei Lu, Kaikai Li and Kaijing liu
The amorphization of single-crystal KTiOPO4 under H and He ion coimplantation is explored by using transmission electron microscopy, Rutherford backscattering spectrometry and high resolution x-ray diffraction. KTiOPO4 crystalline wafers were coimplanted with 110 keV H and 190 keV He at fluences in the range of (6–10) × 1016 cm−2. A 500 nm width amorphization layer and lattice deformation are detected after ion implantation. The critical dpa threshold of 0.26 for continuous amorphous layer formation is obtained in this study. Lattice expansion and contraction is detected and found to be dependent on crystal orientation. These results are discussed in terms of accumulation of damage and lattice structure of KTiOPO4.
025205
Jiejie Shi, Chunxiang Cui, Lichen Zhao, Jinhua Ding, Sen Cui, Shuiqing Liu and Yijiao Sun
Amorphous Al86Y8Ni6 and Al88Y3Ce3Ni6 (at%) alloy ribbons were successfully prepared by melt-spinning technique at the rotation speed of 20 m s−1. The glass forming ability of Al88Y3Ce3Ni6 alloy was superior to Al86Y8Ni6 alloy, which was analyzed by thermodynamic caculation. The α-Al nanoparticles embedded in the Al88Y3Ce3Ni6 glass matrix were formed during primary crystallization. The kinetic parameters of the three crystallization processes were determined by Kissinger, Ozawa and Augis-Bennet methods. The calculation based on Kissinger-Akahira-Sunose (KAS) and Ozawa-Flynn-Wall (OFW) model suggest that the local activation energy decreases with the volume fraction of crystallized increases during the first crystallization process. The high E(α) (α < 0.1) and Ex of crystallization imply the good thermal stability of the Al88Y3Ce3Ni6 amorphous alloy.
025206
Yunhua Zhang, Zhipeng Zhang and Zhichao Liu
A new preconditioning method was developed to PVA fibers as the reinforcement in cement-based materials. Virgin PVA fibers exhibits limited adhesion to graphite powders due to the presence of oil spots on the surface. Mixing PVA fibers with a moderately concentrated KMnO4-H2SO4 solution can efficiently remove the oil spots by oxidation without creating extra precipitate (MnO2) associated with the reduction reaction. This enhances the coating of graphite powders onto fiber surface and improves the mechanical properties of PVA fiber reinforced concrete (PVA-FRC). Graphite powders yields better fiber distribution in the matrix and reduces the fiber-matrix bonding, which is beneficial in uniformly distributing the stress among embedded fibers and creating steady generation and propagation of tight microcracks. This is evidenced by the significantly enhanced strain hardening behavior and improved flexural strength and toughness.
025207
E A Abdel Wahab and Kh S Shaaban
B2O3–SiO2–Na2O–Al2O3–TiO2 glasses modified by SnO2 have prepared and characterized by UV–spectroscopy before and after plasma treatment and by ultrasonic techniques. Makishima–Mackenzie Model has been applied to determine the elastic moduli of glasses. The density and the elastic moduli either determined from the ultrasonic or that computed according to the Makishima–Mackenzie model increase as the SnO2 concentration increases. The values of the optical band gap Eg before and after plasma treatment, and refractive index have been determined. It was found that these parameters are sensitive to the increase of SnO2 content. The vibration temperature of nitrogen glow discharge has been calculated using Boltzmann plots of second positive system N2 (C3Πu) → (B3 Πg). The obtained results of vibration temperature decrease with increasing of gas pressure at different discharge currents.
025208
P P Zhou, G Q Wu, Y Tao, X Cheng, J Q Zhao and H Nan
The binder composition used for ceramic injection molding plays a crucial role on the final properties of sintered ceramic and to avoid defects on green parts. In this study, the effects of binder compositions on the rheological, microstructures and the mechanical properties of CaO based ceramic cores were investigated. It was found that the optimized formulation for dispersant, solid loading was 1.5 wt% and 84 wt%, respectively. The microstructures, such as porosity, pore size distribution and grain boundary density were closely related to the plasticizer contents. The decrease of plasticizer contents can enhance the strength of the ceramic cores but with decreased shrinkage. Meanwhile, the creep resistance of ceramic cores was enhanced by decreasing of plasticizer contents. The flexural strength of the core was found to decrease with the increase of the porosity, the improvement of creep resistance is closely related to the decrease of porosity and grain boundary density.
Polymers
025301
Mehmet Bulut, Mohamad Alsaadi and Ahmet Erkliğ
Present study compares the tensile and impact characteristics of Kevlar, carbon and glass fiber reinforced composites with addition of microscale silicon carbide (SiC) within the common matrix of epoxy. The variation of tensile and impact strength values was explored for different content of SiC in the epoxy resin by weight (0, 5, 10, 15 and 20 wt%). Resulting failure characteristics were identified by assisting Charpy impact tests. The influence of interfacial adhesion between particle and fiber/matrix on failure and tensile properties was discussed from obtained results and scanning electron microscopy (SEM) figures. It is concluded from results that the content of SiC particles, and fiber types used as reinforcement are major parameters those effecting on tensile and impact resistance of composites as a result of different interface strength properties between particle-matrix and particle-fiber.
025302
Mehdi Abdollahi Azghan and Reza Eslami-Farsani
The current study aimed at investigating the effects of different stacking sequences and thermal cycling on the flexural properties of fibre metal laminates (FMLs). FMLs were composed of two aluminium alloy 2024-T3 sheets and epoxy polymer-matrix composites that have four layers of basalt and/or glass fibres with five different stacking sequences. For FML samples the thermal cycle time was about 6 min for temperature cycles from 25 °C to 115 °C. Flexural properties of samples evaluated after 55 thermal cycles and compared to non-exposed samples. Surface modification of aluminium performed by electrochemical treatment (anodizing) method and aluminium surfaces have been examined by scanning electron microscopy (SEM). Also, the flexural failure mechanisms investigated by the optical microscope study of fractured surfaces. SEM images indicated that the porosity of the aluminium surface increased after anodizing process. The findings of the present study showed that flexural modulus were maximum for basalt fibres based FML, minimum for glass fibres based FML while basalt/glass fibres based FML lies between them. Due to change in the failure mechanism of basalt/glass fibres based FMLs that have glass fibres at outer layer of the polymer composite, the flexural strength of this FML is lower than glass and basalt fibres based FML. After thermal cycling, due to the good thermal properties of basalt fibres, flexural properties of basalt fibres based FML structures decreased less than other composites.
025303
Isha Gawri, R Ridhi, K P Singh and S K Tripathi
Ethanol sensing properties of chemically synthesized titanium dioxide (TiO2) and polyaniline/titanium dioxide nanocomposites (PANI/TiO2) had been performed at room temperature. In-situ oxidative polymerization process had been employed with aniline as a monomer in presence of anatase titanium dioxide nanoparticles. The prepared samples were structurally and morphologically characterized by x-ray diffraction, fourier transform infrared spectra, high resolution-transmission electron microscopy and field emission-scanning electron microscopy. The crystallinity of PANI/TiO2 nanocomposite was revealed by XRD and FTIR spectra confirmed the presence of chemical bonding between the polymer chains and metal oxide nanoparticles. HR-TEM micrographs depicted that TiO2 particles were embedded in polymer matrix, which provides an advantage over pure TiO2 nanoparticles in efficient adsorption of vapours. These images also revealed that the TiO2 nanoparticles were irregular in shape with size around 17 nm. FE-SEM studies revealed that in the porous structure of PANI/TiO2 film, the intercalation of TiO2 in PANI chains provides an advantage over pure TiO2 film for uniform interaction with ethanol vapors. The sensitivity values of prepared samples were examined towards ethanol vapours at room temperature. The PANI/TiO2 nanocomposite exhibited better sensing response and faster response-recovery examined at different ethanol concentrations ranging from 5 ppm to 20 ppm in comparison to pure TiO2 nanoparticles. The increase in vapour sensing of PANI/TiO2 sensing film as compared to pure TiO2 film had been explained in detail with the help of gas sensing mechanism of TiO2 and PANI/TiO2. This provides strong evidence that gas sensing properties of TiO2 had been considerably improved and enhanced with the addition of polymer matrix.
025304
Lingfeng Yang, Haopeng Cai, Bin Zhang, Siqi Huo and Xi Chen
Novel electromagnetic functionalized carbon nanofibers (CNFs) have been synthesized by coating with Fe3O4 magnetite nanoparticles and conducting polymers polyaniline (PANI) on CNFs through a layer by layer assembly. The Fe3O4@CNFs were first prepared by coating nano-Fe3O4 particles on CNFs via co-precipitation method; Then the PANI was coated on Fe3O4@CNFs using an in situ polymerization process to obtain PANI@Fe3O4@CNFs nanoparticles. The prepared PANI@Fe3O4@CNFs nanoparticles were dispersed in the epoxy matrix to fabricate microwave absorbing nanocomposites. Compared with the Fe3O4@CNFs/epoxy nanocomposites, the PANI@Fe3O4@CNFs/epoxy nanocomposites exhibit better microwave absorbing properties. The composite containing 15 wt% of PANI@Fe3O4@CNFs with the thickness of 2 mm showed a minimum reflection loss (RL) value of −23.7 dB with an effective absorption bandwidth which is about 3.7 GHz (11.9–15.6 GHz) in the frequency range of 1–18 GHz, indicating that it is an attractive candidate for efficient microwave absorber. A potential absorption mechanism was proposed for enhancement of the impedance-matching condition and electromagnetic wave-attenuation characteristic of materials. Specifically, the impedance-matching condition was improved by the combination of conductive polymers and magnetic nanoparticles with CNFs. The electromagnetic wave attenuation characteristic was enhanced by multiple reflections, due to the increased propagation paths.
025305
V Kostopoulos, A Kotrotsos, P Tsokanas and S Tsantzalis
In this work, nylon micro-particles, both undoped and doped with multiwall carbon nanotubes played the role of the self-healing agent into carbon fibre/epoxy composites (CFRPs). These micro-particles were blended with epoxy matrix and the resulting mixture was used for the composites fabrication. Three types of composites were manufactured; the reference CFRP and the modified CFRPs with undoped and doped nylon micro-particles. After manufacturing, these composites were tested under mode I and II fracture loading conditions and it was shown that the interlaminar fracture toughness characteristics of both nylon modified composites were significantly increased. After first fracture, healing process was activated for the tested nylon modified samples and revealed high fracture toughness characteristics recovery. Morphology examinations supported the results and elucidated the involved toughening and failure mechanisms. Finally, the in-plane mechanical and thermo-mechanical properties of all the composites were characterized for identifying possible knock-down effects due to the nylon modification of composites.
025306
Yongxi He, Yingguang Li, Nanya Li and Xiaozhong Hao
Curing rate is the variation rate of degree of cure with time, which is a crucial issue in the curing process of composite structures since it has a significant influence on the generation of voids and residual stresses. In this paper, an online monitoring method of degree of cure was presented based on refractive index measurement. The influence of cure and temperature variation on the refractive index of composite was separated in real time with a step-temperature refractive index separation method. Non-isothermal microwave curing process of carbon fiber/epoxy composite was monitored, and the degree of cure was obtained with a low measurement error of ±1.5% compared with that determined by off-line DSC measurement. The online monitoring method is a promising technology for smart manufacturing of composite structures.
025307
M Juliyana and R Santhana Krishnan
The sandwich composite panels consisting of facesheet and core material are used as a primary structural member for aerospace, civil and marine areas due to its high stiffness to weight ratio. But the debonding nature of facesheet from the foam core under shear loading conditions leads to failure of the composite structure. To inhibit the debonding, an innovative methodology of introducing semi-torus key is used in the present study. The polyvinyl chloride foam core(PVC) is grooved and filled with semi-torus shaped chopped strand prepregs which are sandwiched between alternate layers of woven roven(WR) and chopped strand mat(CSM) skins by vacuum infusion process. The sandwich panel manufactured with semi-torus keys is evaluated regarding experimental and numerical simulations under shear loading conditions. The present innovative concept delays the debonding between face-sheet and foam core with enhancement the shear load carrying capability as the initial stiffness is higher than the conventional model. Also, the shear behaviour of the proposed concept is in good agreement with experimental results. The split semi-torus keys sustain the shear failure resulting in resistance to debonding capability.
025308
Peng Shang, Chengli Shao, Qiqing Li and Chifei Wu
Acrylonitrile-butadiene rubber (NBR) composites filled with Cobalt (II) Chloride (CoCl2) particles were prepared by a solvent dispersion method. Acetone was selected as solvent for NBR and CoCl2. To directly enhance the interaction between NBR and CoCl2, a coordination reaction was generated by hot pressing at 200 °C. Fourier transform infrared spectroscopy (FT-IR), ultraviolet-visible spectroscopy (UV–vis), and x-ray photoelectron spectroscopy (XPS) were employed to investigate the coordination reaction. Results showed that the coordination reaction occurred between the nitrile groups (−CN) of NBR and cobalt ions (Co2+) of CoCl2. Compared with the properties of pure NBR, the tensile strength of NBR/CoCl2 composites filled with 10 parts per hundreds of rubber (phr) CoCl2 increased 2200%. Scanning electron microscopy (SEM) indicated that the CoCl2 particles were dispersed in the NBR matrix homogeneously. The indistinguishable interface between CoCl2 particles and NBR matrix indicated good compatibility. Additionally, thermogravimetric analysis (TGA) showed that coordination reaction improved heat resistance of NBR matrix.
025309
Qili Sun, Chao Sang, Zhen Wang and Yunjun Luo
Bonding agents as additional modifiers are used to improve the reinforcement effect between binder and high solid filler in propellant formula. However, polar bonding agents are easily soluble with polar plasticizer and weak bonding effect. Thus, grafting the bonding group into binder to form neutral polymeric is a novel approach to avoid the preceding shortcomings mentioned and is also meaningful to improve interface properties of propellant. In this work, glycidyl azide polyol energetic thermoplastic elastomer binder with –CN bonding group (named G-1binder) was synthesized and the influences of –CN bonding groups on the mechanical and creep resistance properties of G-1/RDX composites were studied. Then, the mechanism of interfacial interactions between binder with –CN group and cyclotrimethylenetrinitramine (RDX) were also illustrated through Fourier transform infrared spectroscopy, x-ray photoelectron spectroscopy and contact angle analyzer. Results demonstrated G-1/RDX propellants have stronger interfacial reinforcement effect and good mechanical and creep resistant properties. As well, the induced effect model was proposed, and the binding energy of interface was calculated by Materials Studio software. Computational results show that G-1/RDX propellant has a high binding energy and strong interactive force due to the existence of induced effect between –CN group and –NO2 group, which resulted in an increase in constrained regions around the RDX surface and led to the significant promotions of mechanical and creep resistance properties of G-1/RDX propellant.
025310
Weizhou Zhang, Jiawei Ren, Ting Wei and Weihong Guo
In this paper, the synergistic effect of ammonium polyphosphate (APP) and expandable graphite (EG) on flame-retarded poly(butylene terephthalate) (PBT) was systermically investigated using limiting oxygen index (LOI), UL-94 testing, microscale combustion calorimetry (MCC), thermal-gravimetric analysis (TGA) and scanning electronic microscopy (SEM). PBT composites containing 20 wt% of APP: EG (1:3) combinations exhibits a high LOI value of 29.8 and reaches V-0 rating in UL-94 testing, indicating that the flame retardant property is greatly enhanced compared to the composites solely with APP or EG. SEM images show that the combination of APP and EG could promote the formation of a compact char layer. The compact char layer protects the PBT resin efficiently by preventing penetration of heat flux inside the matrix and retards the decomposition of PBT, consequently improves the thermal stability of PBT materials as revealed by TGA. All of the results demonstrate that APP and EG are high efficiency synergists for improving the flame retardation of PBT materials.
Biological and biomedical materials
025401
Sai-Jun Lin, Ya-Ping Xue, Guoqing Chang, Qiao-Ling Han, Li-Fang Chen, Yan-Bo Jia and Yu-Guo Zheng
The development of three-dimensional (3D) nanofiber structures by electrospinning has drawn considerable attention in the field of tissue scaffolds. However, the generation of two dimensional mats using the conventional method limits electrospinning, the electrical charging of polymer liquids, as a means of nanofiber fabrication. In this study, we established a facile method of fabrication of layer-by-layer 3D polycaprolactone (PCL) nanofiber structures by utilizing a booklet collector with controlled morphology. Meanwhile, we explore the application of the manufactured 3D architectures in the field of tissue scaffolds. The approximately 20 μm layer-to-layer distance enhanced the ability of cells to migrate freely into tissues and induce cells in an ordered arrangement.
025402
Mauricio Rangel Seixas, Celso Bortolini Jr, Adelvam Pereira Jr, Roberto Z Nakazato, Ketul C Popat and Ana Paula Rosifini Alves Claro
Metallic biomaterials have been used for biomedical applications, such as cardiovascular, orthopaedics and orthodontics, due to excellent properties. In this study, the mechanical properties and corrosion resistance of new quaternary alloy Ti25Ta25Nb3Sn were evaluated. Alloys were processing in arc melting furnace with argon atmosphere and cold worked by rotary swaging. Alloy microstructure, crystalline phases and mechanical properties such as Young’s modulus, yield strength and tensile strength were evaluated. Corrosion resistance was investigated in fluoride solution by electrochemical polarization and biocompatibility with human dermal fibroblasts were also evaluated. In our study, for quaternary alloy Ti25Ta25Nb3Sn the stabilization of beta phase was maintained. It was observed that the elastic modulus of Ti25Ta25Nb3Sn (65 GPa) was lower than CP Ti (105 GPa) and Ti6Al4V (110 GPa) and slightly higher than Ti25Ta25Nb (55 GPa) alloy. The addition of Sn suppressed the double yielding verified on ternary alloy Ti25Ta25Nb. Electrochemical studies showed that stable passive oxide film was formed on the Ti25Ta25Nb3Sn surface and an increase of HDF adhesion and proliferation on alloy surface, indicating that the alloy is non-cytotoxic may provide a favorable material for biomedical applications. Results obtained showed that Ti25Ta25Nb3Sn alloy is indicated for biomedical applications.
025403
B H Nanjunda Reddy, Pradipta Ranjan Rauta, V Venkatalakshimi and Swamy Sreenivasa
The aim of this research is to inspect the effect of Cloisite-30B (C30B) modified clay dispersed poly (acrylamide-co-Sodiumalginate)/AgNp hydrogel nanocomposites (PASA/C30B/Ag) for drug delivery and antibacterial activity. A novel hydrogel composite based sodium alginate (SA) and the inorganic modified clay with silver nano particle (C30B/AgNps)polymer hydrogel composites are synthesized via the graft copolymerization of acrylamide (AAm) in an aqueous medium with methylene bisacrylamide (MBA) as a crosslinking agent and ammonium per sulfate(APS) as an initiator. The UV/Visible spectroscopy of obtained composites is successfully studied, which confirms the occurrence of AgNps in the hydrogel composites. And the swelling capacity and bovine serum albumin (BSA) protein as model drug delivery study for these hydrogel nanocomposites have been carried out. The C30B/Ag filled hydrogel composites exhibit superior water absorbency or swelling capacity compared to pure samples and it is establish that the formulations with clay (C30B) dispersed silver nanocomposite hydrogels show improved and somewhat faster rate of drug delivery than other formulations(pure systems) and SEM and TEM reports suggests that the size of AgNps in the composite hydrogels is in the range of 5–10 nm with shrunken surface and the antibacterial characterizations for gram positive and gram negative bacteria are carried out by using Streptococcus faecalis (S. Faecalis) and Escherichia coli (E.coli) as model bacteria and the hydrogel composites of PASA/C30B/Ag shows exceptional antibacterial activity against both the bacteria as compared to pure hydrogel composites samples.
025404
Caifeng Chen, Yuan Zhu, Jun Ji, Feixiang Cai, Youming Zhang, Ningyi Zhang and Andong Wang
Porous lithium sodium potassium niobate (LNK) ceramic has excellent piezoelectric properties, chemical stability and great chemical compatibility. It has a good application potential in the field of biological bone substitute. In the paper, porous LNK ceramic was fabricated with egg albumen foaming agent by foaming method. Effects of preparation process of the porous LNK ceramic on density, phase structure, hole size and piezoelectric properties were researched and characterized. The results show that the influence factors of LNK solid content and foaming agent addition are closely relevant to properties of the porous LNK ceramic. When solid content is 65% and foaming agent addition is 30%, the porous LNK ceramic has uniform holes and the best piezoelectric properties.
025405
Juan Li, Guanghui Zhao, Huiqin Chen, Qingxue Huang, Lifeng Ma and Wei Zhang
Hot deformation behavior of as-cast antibacterial austenitic stainless steel with 2.42% copper was investigated in the temperature range of 900 °C–1150 °C, and the strain rates ranged from 0.01 to 20 s−1. At strain rates higher than 1 s−1, the flow stress curves were corrected by considering adiabatic heating. Kinetic analysis indicated that the hot deformation activation energy of the steel was 375.65 kJ mol−1. The dynamic recrystallization (DRX), misorientation, and twins were analyzed using optical microscope or electron backscatter diffraction. The results showed that DRX mechanism in hot deformation mainly corresponded to discontinuous recrystallization at high temperature and with a high rate. By increasing the temperature and strain rate, the recrystallization degree and the twin ratio increased simultaneously. Both of these factors promoted one another.
025406
Nibedita Dey, T Devasena and Tamilarasu Sivalingam
This work reports a comparative study on the development of a sensitive voltammetric method for the assay of diferuloylmethane which is fabricated using cost-effective sensing material graphene oxide (GO modified electrode) and reduced graphene oxide (rGO modified electrode) modified on glassy carbon electrode respectively. The prepared materials were characterized using SEM, XRD, FTIR, and Raman techniques to understand the formation. Between the both modified electrodes, rGO modified electrode demonstrated a lower limit detection of 0.9 pM and good signal quality. But, the better linear dynamic range for detection was found to be 1 nm to 100 nM for GO and 0.1 nM to 10 nM for rGO modified electrodes respectively. The repeatability is checked for seven cycles and interference studies were also performed for checking the sensors’ selectivity to curcumin. rGO modified electrode and GO modified electrode both shows specific signals for Diferuloylmethane under conditions similar to physiology. But, with better properties over GO modified electrode, rGO modified electrode is suggested a better candidate for real-time usability in sensing. The detection limit reported is the lowest till date for the given plant drug using any sensing assay.
025407
Swamiappan Sathiskumar, Sekar Vanaraj, Devaraj Sabarinathan and Kathirvel Preethi
Materials based on hydroxyapatite (HAp) Synthesized from bio-wastes have been regarded as useful, novel, eco-friendly medical applications that are targeted primarily for their antibacterial nature. In the present study, HAp was Synthesized from the fish scales of Labeo rohita using alkaline heat treatment and subsequently mixed with 1, 2 and 3 wt% of zinc (Zn) at 800 °C using calcination method to yield Zn-HAp composites. A detailed characterization of the generated composites was analysed by XRD, FT-IR, SEM, EDX and DLS methods. Further, antibacterial and biofilm inhibitory activity of the generated composites was determined using strains of Staphylococcus aureus and Escherichia coli. The confirmation of the presence of zinc, confirmed by EDAX spectra, XRD, FT-IR, SEM and DLS observations, established that HAp and Zn-HAp composites were without impurities, irregular in shape and were 848 nm sized particles. Although 1–3 wt% Zn-HAp composites showed antibacterial activity, the 3 wt% Zn-HAp composite was found suitable to kill the surrounding bacterial growth and showed potent inhibitory activity against biofilm formation.
Energy and environment materials
025501
Can He, Haipeng Ji, Zhaohui Huang, Xiaoguang Zhang, Haitao Liu, Silin Liu, Yangai Liu, Minghao Fang, Xiaowen Wu and Xin Min
A series of ZnAl2−xO4:xEu3+ phosphors was synthesized by a modified co-precipitation method. The phase structure and photoluminescence properties were examined and extensively discussed. Composition-optimized ZnAl1.97O4:0.03Eu3+ exhibited sharp, intense red characteristic emissions with the Commission Internationale de l’Eclairage coordinates of (0.62, 0.33) peaking at 620 nm under an excitation at 394 nm, corresponding to the 5D0 → 7F2 transition of Eu3+. The quenching concentration of Eu3+ in ZnAl2−xO4:xEu3+ phosphors was approximately 0.03. In addition, the concentration quenching mechanism, fluorescence decay curves, and thermally stable luminescence properties of ZnAl2–xO4:xEu3+ phosphors were investigated. The results indicated that ZnAl2–xO4:xEu3+ phosphors demonstrate potential applications in near-ultraviolet light-emitting diode pumped white light lamps.
025502
Peiyuan Zeng, Fangfang Qian, Yingwu Lin, Xiaoxiao Wang, Jianwen Li, Wanwan Wang, Feng Tao and Zhen Fang
Flower-like α-Fe2O3−δ nanostructures have been successfully synthesized via a one-step hydrothermal method. The as-prepared α-Fe2O3−δ nanostructures exhibited a good cyclability and rate performance. The discharge capacity could retain as high as 1192.4 mAh g−1 (current density: 400 mA g−1) after 800 cycles, which is higher than the theoretical value of hematite. When the current density increased to 3200 mA g−1, the reversible capacity is about 660 mAh g−1. The good electrochemical performance of α-Fe2O3−δ nanostructures could be attributed to the combination of both nano-structuring strategy and oxygen vacancies in the as-prepared materials, which improve the structure mechanism strength, electric conductivity and facilitate the diffusion of Li ions.
025503
Zhaoyu Yin, Xiaoguang Zhang, Zhaohui Huang, Silin Liu, Weiyi Zhang, Yan’gai Liu, Xiaowen Wu, Minghao Fang and Xin Min
Expanded graphite/β-SiC nanowires composites (ESNC) were prepared through chemical vapor deposition, and paraffin/expanded graphite/β-SiC nanowires composites (PESNC) were made through vacuum impregnation to overcome liquid leakage during phase transition and enhance the thermal conductivity of paraffin. Fourier transform infrared spectroscopy showed no chemical interactions between the paraffin and ESNC. Differential scanning calorimetry estimated the temperature and latent heat of PESNC during melting to 45.73 °C and 124.31 J g−1, respectively. The respective values of these quantities during freezing were recorded as 48.93 °C and 124.14 J g−1. The thermal conductivity of PESNC was estimated to 0.75 W mK−1, which was 3.26-folds that of pure paraffin (0.23 W mK−1). PESNC perfectly maintained its phase transition after 200 melting–freezing cycles. The resulting ideal thermal conductivity, good chemical stability, thermal properties and thermal reliability of PESNC are promising for use in energy efficient buildings and solar energy systems.
025504
Yongmei Xia, Zuming He, Wei Yang, Bin Tang, Yalin Lu, Kejun Hu, Jiangbin Su and Xiaoping Li
Novel BiOI/Cu2O composites were designed and synthesized for the first time by coupling reduction method at low temperature. The samples were characterized by XRD, XPS, SEM, EDS, HRTEM, UV–vis (DRS), FTIR and photo-electro-chemical (PEC) analysis. Results showed that the BiOI/Cu2O composites consisted of three-dimensional (3D), hierarchical cauliflower-like structure composed of BiOI nanosheet and Cu2O cubic submicrometer structure, the composite absorption band broadened, and the absorption intensity in the visible region strengthened. And the composites exhibited an excellent photocatalytic performance, which might be attributed to the improvement of the composite absorption and effective charge separation in BiOI/Cu2O composites. In addition, the possible photocatalytic mechanism was proposed.
025505
Zhilei Miao, Lei Chen, Rui Wang, Rongchun Yuan, Fang Zhou, Pengfei Lv, Xiuyun Zhang and Qiang Wang
BaTiO3(BTO) powders with cubic(C) and tetragonal(T) crystalline structures were prepared by sol-gel method followed by calcination at different temperatures, and they were decorated with gold nanoparticles(AuNPs) to form Au-T-BTO and Au-C-BTO respectively. All the samples (C-BTO, T-BTO, Au-C-BTO and Au-T-BTO) were used as photo-catalysts for the degradation of Rhodamine B (RhB). Au-T-BTO exhibits the highest photocatalytic activity due to thecombined effect of surface plasmon resonance (SPR) and the ferroelectricity of the tetragonalphase BTO. The light absorption peaks at 500 to 600 nm verify the presence of SPR effect from Au NPs. Based on density functional theory (DFC) within the generalized gradient approximation (GGA) approach, it was demonstrated that the tetragonal phase BaTiO3 shows a spontaneous polarization with the calculated value of 0.34 C m−2, which is absent in thecubic phase. The internal space charge layer in tetragonal phase BTO enhances the separation of photoexcited carriers due to the spontaneous ferroelectric polarization, which also benefits photocatalytic activities.
025506
Amirhosein Habibi, Maisam Jalaly, Roohollah Rahmanifard and Milad Ghorbanzadeh
In this study, the NCM cathode with a chemical composition of
were synthesized through a solution combustion method. In this method, metal nitrates and urea were used as precursors and fuel, respectively. The powder obtained from combustion were transferred into a alumina crucible and insert to the muffle furnace and calcined at 750 °C for 15 h. The crystallite size of the sample was calculated with sherer equation to be about 41 nm. The prepared cathode were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetry analysis (TGA), differential scanning calorimetry (DSC) and battery charge-discharge test. The initial charge and discharge capacities of
electrode containing 94% active material at a rate of 0.05 C in voltage window of 2.5–4.3 V at room temperature was obtained 168.03 and 150.01 mAh g−1, respectively.
025507
S Rajeshwari, J Santhosh Kumar, R T Rajendrakumar, N Ponpandian and P Thangadurai
Pure and different concentrations of Sn4+ doped V2O5 (Sn:V2O5) nanorods were synthesized by hydrothermal method. The Sn:V2O5 nanorods obtained were orthorhombic in structure. No secondary phase was observed up to 10% of Sn doping, but beyond that, there evolved a secondary phase of SnO2. Microstructural analysis revealed the morphology of V2O5 as nanorods and platelets like structure. Presence of V, O and Sn elements in the samples was confirmed by energy dispersive spectroscopy. The V2O5 nanorods have shown a strong absorption in the visible region and the band gap energy was obtained to be varying from 2.21 to 2.26 eV as a function of Sn ion doping. Photocatalytic studies on methylene blue (MB) under visible light irradiation showed that the 3% Sn:V2O5 had effectively degraded MB up to a maximum degradation of 96% and further increase in Sn content had decreased the photodegradation due to higher recombination rate of photogenerated electrons. The mechanism of photodegradation was completely understood and the OH· radicals have played a dominant role in the photodegradation of the organic dyes.
025508
Ali Afzali Nezhad, Mohammad Alimoradi and Majid Ramezani
Herein, we report a novel one-step strategy to construct magnetic nanocomposite (polypyrrole/GO@Fe3O4) via a simple and effective chemical method. First, the GO nanosheets were fabricated through modified Hummers method, and then, the Fe3O4 nanoparticles and polypyrrole were decorated on surface of the GO nanosheets by coprecipitation of ferrous salts and pyrrole monomer in GO suspension. The ferric chloride could act both as oxidizing agent and also for preparation of magnetic Fe3O4 nanoparticles. The prepared nanomaterials were characterized by transmission electron microscopy (TEM), field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy, x-ray diffraction, and TGA measurements. The prepared magnetic nanocomposite had a much higher thermal stability than pure graphene oxide. The magnetic nanocomposite has been employed as adsorbent for the magnetic separation of Methylene Blue dye from water. The adsorption test of Methylene Blue (MB) demonstrates that it only takes few minutes for MB to attain equilibrium. The effect of experimental conditions such as contact time and pH as well as kinetic and isotherm of adsorption of MB dye was also studied. The highest adsorption capacity for MB was 323.2 mg g−1. The pH optimization experiments showed that pH = 8 is optimum pH for investigation of MB dye adsorption. It is also must be mentioned that most of adsorption of MB dye achieved within first 10 min of exposure to MB dye which indicated the strong interaction between dye molecules and adsorbent and high rate of adsorption of dye on magnetic nanocomposite. Adsorption procedure of dye were fitted well by pseudo-second-order kinetic and Langmuir isotherm models. The cycling reusability of magnetic nanocomposite showed comparable values to other studies. Results showed that the prepared new magnetic nanocomposite has great potential application for removal of organic dyes from polluted water.
025509
Jiatong Liu, Cuifeng Sun, Ming Fu, Jie Long, Dawei He and Yongsheng Wang
The development of porous materials exhibiting photon regulation abilities for improved photoelectrochemical catalysis performance is always one of the important goals of solar energy harvesting. In this study, methods to improve the photocatalytic activity of TiO2 inverse opals were discussed. TiO2 inverse opals were prepared by atomic layer deposition (ALD) using colloidal crystal templates. In addition, TiO2 inverse opal heterostructures were fabricated using colloidal heterocrystals by repeated vertical deposition using different colloidal spheres. The hydrothermal method and ALD were used to prepare ZnO- or Fe2O3-modified TiO2 inverse opals on the internal surfaces of the TiO2 porous structures. Although the photonic reflection band was not significantly varied by oxide modification, the presence of Fe2O3 in the TiO2 inverse opals enhanced their visible absorption. The conformally modified oxides on the TiO2 inverse opals could also form energy barriers and avoid the recombination of electrons and holes. The fabrication of the TiO2 photonic crystal heterostructures and modification with ZnO or Fe2O3 can enhance the photocatalytic activity of TiO2 inverse opals.
025510
Cuiqin Li, Qianlin Chen, Yunan Yan, Yanan Li and Ying Zhao
A series of Ca0.92La0.04RE0.04MnO3 (RE = Sm, Dy and Yb) compounds are synthesized via a coprecipitation technique. The influence of La/RE dual doping on the phase structure, microstructure and thermoelectric properties of the CaMnO3 system is investigated. Increased material density with grain sizes of 1–2 μm and a homogeneous microstructure is realized. Dual doping decreases the electrical resistivity due to an increase in the carrier concentration and also decreases the thermal conductivity due to increased grain scattering, damping of local vibrations by heavier La/RE ions compared to Ca and lattice distortion. The Ca0.92La0.04Yb0.04MnO3 shows the highest power factor of 3.49 × 10−4 W m−1 K−2 and the highest dimensionless figure of merit ZT of 0.25 at 770 K, which is approximately 3 times larger than that obtained for the undoped CaMnO3 and significantly larger than that of single-doped CaMnO3 prepared by solid-state reaction. This work provides a basic foundation for the industrial application of this thermoelectric material.
025511
P C Nagajyothi, M Pandurangan, T V M Sreekanth and Jaesool Shim
Tricobalt tetraoxide or cobalt oxide (Co3O4) nanocubes (NCs) were synthesized from the self-assemblies of Co3O4 nanoparticles (NPs) via a simple one-step hydrothermal method. X-ray diffraction analysis confirmed the cubic crystal structure of Co3O4 NCs. The surface properties were investigated by x-ray photoelectron spectroscopy, which suggests the co-existence of Co in +2 and +3 states. The self-assemblies of aggregation of NPs to NCs were inspected using scanning electron microscopy, which is supported by transmission electron microscopy. The electrochemical properties of Co3O4 NCs were carried out by cyclic voltammetry (CV), galvanostatic charge-discharge (GCD) curves and impedance analysis. The areal capacitance of 3.04 mF cm−2 was obtained at current density of 10 μA cm−2. The Co3O4 NCs electrode exhibits good long-cyclic stability with 92.1% capacitance retention over 3000 cycles. The CV, GCD and impedance curves of Co3O4 NCs were recorded after cyclic test, which are similar to the curves recorded before the test. Therefore, the Co3O4 NCs serves good candidate as positive electrode materials for asymmetric supercapacitors.
025512
Mahfooz ur Rehman, Wajid Rehman, Muhammad Waseem, Sirajul Haq, Khizar Hussain Shah and Peng Kang
In this study, ternary nanocomposite (TNC) was synthesized by microemulsion method by taking Sn, Ti and Fe in (1:1:1) molar ratio. The BET surface area and pore size were measured by nitrogen adsorption method. The morphological features of TNC like particle size, elemental percentage and crystallite size were studied by scanning electron microscopy (SEM), energy dispersive x-rays (EDX) and x-rays diffraction (XRD) respectively, whereas the surface functional groups were detected by Fourier Transform Infrared (FTIR) spectroscopy. The crystallite size was found to be 11 nm, calculated from FWHM of diffraction peak with relative intensity 100%. For the thermal stability of TNC, thermogravimetric analysis (TGA) was performed. Batch adsorption tests were used for the removal of Pb2+ ions from aqueous solutions. The maximum adsorption capacity in this study was found to be 79.56 mg g−1 at 40 °C which is promising than the values reported in the literature. Based on the regression coefficient (r2), the adsorption data was found well fitted to the Langmuir as compared to Freundlich model. The exchange of a single proton with every Pb2+ ion was calculated. Thermodynamic parameters were indicative for the sorption process to be endothermic and spontaneous.
025513
Yahia Gacemi, Ali Cheknane and Hikmat S Hilal
Physiochemical processes at the photo-electrode and the counter electrode of dye sensitized solar cells (DSSCs) involving having carbon nanotubes (CNTs) instead of the TiO2 layer, within the working electrode, are simulated in this work. Attention is paid to find the effect of CNT layer thickness on photo-electrochemical (PEC) characteristics of the CNT-DSSCs. Comparison with other conventional TiO2-DSSC systems, taking into account the working electrode film thickness, is also described here. To achieve these goals, a model is presented to explain charge transport and electron recombination which involve electron photo-excitation in dye molecules, injection of electrons from the excited dye to CNT working electrode conduction band, diffusion of electrons inside the CNT electrode, charge transfer between oxidized dye and (I−) and recombination of electrons. The simulation is based on solving non-linear equations using the Newton-Raphson numerical method. This concept is proposed for modelling numerical Faradaic impedance at the photo-electrode and the platinum counter electrode. It then simulates the cell impedance spectrum describing the locus of the three semicircles in the Nyquist diagram. The transient equivalent circuit model is also presented based on optimizing current–voltage curves of CNT-DSSCs so as to optimize the fill factor (FF) and conversion efficiency (η). The results show that the simulated characteristics of CNT-DSSCs, with different active CNT layer thicknesses, are superior to conventional TiO2-DSSCs.
025514
Kai Li, Wei-Bin Zhang, Zhi-Yun Zhao, Yue Zhao, Xi-Wen Chen and Ling-Bin Kong
The porous carbon material is obtained via pyrolysis and activation of fructus cannabis’s shells, an easy-to-get biomass source, and is used as an active electrode material for supercapacitors. The obtained carbon exhibit a high specific surface area of 2389 m2 g−1. And the result of x-ray photoelectron spectroscopy (XPS) shows that the obtained porous carbon possess numerous oxygen groups, which can facilitate the wettability of the electrode. The prepared porous carbon also exhibit remarkable electrochemical properties, such as high specific capacitance of 357 F g−1 at a current density of 0.5 A g−1 in 6 mol L−1 aqueous KOH electrolyte, good rate capability of 77% capacitance retention as the current density increase from 0.5 A g−1 to 10 A g−1. In addition, it also presents a superior cycling stability of 100% capacitance retention after 10 000 cycles at the current density of 1 A g−1.
025515
Mengfei Lu, Qiaoqiao Li, Changping Zhou, Chengliang Zhang and Haifeng Shi
The effects of (C, N, S, P)/V co-doping on the electronic structures of indium niobate have been investigated by the first principle calculations based on density functional theory (DFT). The results indicated that some localized V 3d states emerged under the bottom of conduction band (Nb 4d states) along with the existence of localized C 2p (N 2p, S 3p) states above the top of valence band (O 2p states) for C (N, S)/V co-doped InNbO4. As for P/V co-doping, the introduced P 3p levels in the band gap were conducive to cut down the electron transition energy. Moreover, the hybridization of localized V 3d and Nb 4d states contributed to the reduction of band gap energy. According to the calculated results, we tentatively proposed that P/V co-doped InNbO4 would possibly be a promising visible-light responsive photocatalyst in view of the suitable redox potentials of water splitting.
025516
Chung-Hsien Wu, Fu-Shan Chen, Shin-Hom Lin, Chang-Ying Ou and Chung-Hsin Lu
Copper indium gallium diselenide (Cu(In,Ga)Se2) films with different gallium-ion contents were prepared via a spin coating method followed by a selenization process. Increasing the gallium-ion contents of the prepared films decreased the lattice constants and increased the band gaps. Secondary ion mass spectroscopy analysis revealed that Cu(In,Ga)Se2 films with different band gap grading types were successfully fabricated. Increasing the contents of gallium ions near the substrate resulted in an increase in the short-circuit current density. On the other hand, increasing in the contents of gallium ions near the surface of the Cu(In,Ga)Se2 films significantly increased open-circuit voltage Voc. By combining a normal and a reverse grading of gallium-ion contents, Cu(In,Ga)Se2 films with double grading types of gallium-ions contents exhibited superior electrical properties. The conversion efficiency and fill factor of solar cells with a double grading type of gallium-ion contents reached 6% and 58.7%, respectively.
Carbon materials
025601
Sukhendu Jana, Sayan Das, Debasish De, Anup Mondal and Utpal Gangopadhyay
Presently, silicon nitride (SiNx) is widely used as antireflection coating (ARC) on p-type silicon solar cell. But, two highly toxic gasses ammonia and silane are used. In the present study, the ARC and passivation properties of diamond-like nanocomposite (DLN) thin film on silicon solar cell have been investigated. The DLN thin film has been deposited by rf-PACVD process using liquid precursor HMDSO in argon plasma. The film has been characterized by FESEM, HRTEM, FTIR, and Raman spectroscopy. The optical properties have been estimated by UV–vis–NIR spectroscopy. The minimum reflection has been achieved to 0.75% at 630 nm. Both the short circuit current density and open circuit voltage has been increased significantly from 28.6 mA cm−2 to 35.5 mA cm−2 and 0.551 V to 0.613 V respectively. The field effect passivation has been confirmed by dark IV characterization of c-Si /DLN heterojunction structure. All these lead to enhancement of efficiency by almost 4% absolute, which is comparable to SiNx. The ammonia and silane free deposited DLN thin film has a great potential to use as ARC for silicon based solar cell.
025602
Juliana Bovi de Oliveira, Lília Müller Guerrini, Silvia Sizuka Oishi, Luis Rogerio de Oliveira Hein, Luíza dos Santos Conejo, Mirabel Cerqueira Rezende and Edson Cocchieri Botelho
In recent years, reinforcements consisting of carbon nanostructures, such as carbon nanotubes, fullerenes, graphenes, and carbon nanofibers have received significant attention due mainly to their chemical inertness and good mechanical, electrical and thermal properties. Since carbon nanofibers comprise a continuous reinforcing with high specific surface area, associated with the fact that they can be obtained at a low cost and in a large amount, they have shown to be advantageous compared to traditional carbon nanotubes. The main objective of this work is the processing of carbon nanofibers, using polyacrylonitrile (PAN) as a precursor, obtained by the electrospinning process via polymer solution, with subsequent use for airspace applications as reinforcement in polymer composites. In this work, firstly PAN nanofibers were produced by electrospinning with diameters in the range of (375 ± 85) nm, using a dimethylformamide solution. Using a furnace, the PAN nanofiber was converted into carbon nanofiber. Morphologies and structures of PAN and carbon nanofibers were investigated by scanning electron microscopy, Raman Spectroscopy, thermogravimetric analyses and differential scanning calorimeter. The resulting residual weight after carbonization was approximately 38% in weight, with a diameters reduction of 50%, and the same showed a carbon yield of 25%. From the analysis of the crystalline structure of the carbonized material, it was found that the material presented a disordered structure.
025603
Honglei Zhou, Ping Liu, Xiaohong Chen, Liming Bi, Ke Zhang, Xinkuan Liu, Wei Li and Fengcang Ma
Given that the conventional catalyst is easily soluble in the matrix to result in the poor performance of the CNTs/Cu composite materials, the Cr nano-particles precipitated on the surface of Cu-Cr particles are first used as catalysts to prepare the CNTs/Cu composite powders by means of water-assisted chemical vapor deposition in situ synthesis. The results show that the morphological difference of the precipitated Cr nano-particle is obvious with the change of solution and aging treatment, and the morphology, length and diameter of the synthetic CNTs are also different. The catalyst of Cr nano-particle has the best morphology and the synthesized CNTs had a good wettability with Cu particles when the Cu-Cr composite powders was solution-treated at 1023 K for 60 min and then was aged at 723 K for 120 min. The length, diameter, yield and purity of the synthesized CNTs can be also affected by the moisture content in the reaction gas. It is the most suitable for the growth of CNTs when the moisture content is 0.4%, and the high purity and defect-free CNTs with the smooth pipe wall, a diameter of 20 ∼ 30 nm and a length of up to 1800 nm can be obtained. The yield of CNTs with the moisture content of 0.4% reached to 138%, which was increased by 119% to compare with that without moisture. In this paper, a feasible technology was offered for the preparation of high performance CNTs/Cu composites.
025604
Anupam Midya, Subhrajit Mukherjee, Shreyasee Roy, Sumita Santra, Nilotpal Manna and Samit K Ray
This paper presents a highly selective chloroform sensor using functionalised reduced graphene oxide (RGO) as a sensing layer. Thiol group is covalently attached on the basal plan of RGO film by a simple one-step aryl diazonium chemistry to improve its selectivity. Several spectroscopic techniques like X-ray photoelectron, Raman and Fourier transform infrared spectroscopy confirm successful thiol functionalization of RGO. Finally, the fabricated chemiresistor type sensor is exposed to chloroform in the concentration range 200–800 ppm (parts per million). The sensor shows a 4.3% of response towards 800 ppm chloroform. The selectivity of the sensor is analyzed using various volatile organic compounds as well. The devices show enhanced response and faster recovery attributed to the physiosorption of chloroform onto thiol functionalized graphene making them attractive for 2D materials based sensing applications.
025605
Shuai Xie, Jing Wang, Wufeng Wang, Guoyan Hou, Bin Li, Zhonghe Shui and Zhijiang Ji
In order to develop a cement based composites with high electromagnetic (EM) wave absorbing performance, helical carbon fibers (HCFs) were added into the cement matrix as an absorbent. The reflection loss (RL) of the prepared HCFs/cement based composites was studied by arched testing method in the frequency ranges of 1–8 GHz and 8–18 GHz. The results show that the EM wave absorption properties of the cement based composites can be evidently enhanced by the addition of HCFs. The composites with 1.5% HCFs exhibits optimum EM wave absorption performance in the frequency range of 1–8 GHz. However, in 8–18 GHz frequency range, the EM wave absorption performance of the cement composites with 1% HCFs is much better than others. The RL values of the prepared HCFs/cement based composites are less than −5 dB in the whole testing frequency regions, which can be attributed to the strong dielectric loss ability and unique chiral structure of HCFs.
025606
Florian Godel, Christian Meny, Bernard Doudin, Hicham Majjad, Jean-François Dayen and David Halley
We report on the fabrication of ferromagnetic thin layers separated by a MgO dielectric barrier from a graphene-covered substrate. The growth of ferromagnetic metal layers—Co or Ni0.8Fe0.2—is achieved by Molecular Beam Epitaxy (MBE) on a 3 nm MgO(111) epitaxial layer deposited on graphene. In the case of a graphene, grown by chemical vapor deposition (CVD) over Ni substrates, an annealing at 450 °C, under ultra-high-vacuum (UHV) conditions, leads to the dewetting of the ferromagnetic layers, forming well-defined flat facetted clusters whose shape reflects the substrate symmetry. In the case of CVD graphene transferred on SiO2, no dewetting is observed after same annealing. We attribute this difference to the mechanical stress states induced by the substrate, illustrating how it matters for epitaxial construction through graphene. Controlling the growth parameters of such magnetic single objects or networks could benefit to new architectures for catalysis or spintronic applications.
Smart materials
025701
Priyanka Rajpoot, Anugya Rastogi and U P Verma
Structural, electronic, optical and thermal properties of molybdenum aluminum boride (MoAlB) have been analyzed systematically using the full potential linearized augmented plane wave method based on density functional theory at ambient condition as well as high pressure and high temperature. Density of states and band structure calculation reflect the metallic character of MoAlB. In addition to this, the electron charge density calculation reveals the strong covalent bonding, in between ‘B’ atoms as well as ‘Mo’ and ‘B’ atoms. Optical parameters exhibit anisotropic nature and MoAlB become transparent in ultraviolet region for the radiation of energy above 25 eV. The thermal properties were investigated by using the quasi-harmonic Debye model at high temperature and high pressure.
025702
S S Lucas and J L Barroso de Aguiar
Mortars, one of the most common construction materials, have not received any substantial modification for many decades. This has changed in recent years; new compositions are now being developed, with new properties, using nano-additives, fibres and capsules. In this work, surfaces with new and innovative functionalities that promote energy savings and improve air quality have been developed and studied. Incorporation of phase change materials (PCM) and titanium dioxide (TiO2) nanoparticles in construction products is currently under study by different research groups. However, these studies only address their incorporation separately. Adding new additives into the mortar’s matrix can be complex—due to microstructural modifications that will influence both fresh and hardened state properties. Moving from a single additive to multiple additions, as in this study, increases the system’s complexity. Only with a good understanding of the microstructural properties, it is possible to add multiple additives (including nano and microparticles) to mortars, without damaging its final quality. This work demonstrates that a higher additive content is not always a guarantee of better results; lower additions can often provide a better compromise between performance and final mechanical properties. The results presented in this paper confirmed this and show that combining PCM microcapsules and TiO2 nanoparticles open a new path in the development of mortars with multiple functionalities. In this study, a new material with depolluting, self-cleaning and heat storage was created. For the development of new and innovative mortars, a proper balance of multiple additives, supported by the study of microstructural changes, can lead to an optimization of the compositions, ensuring that the mortar’s final properties are not affected.
Metamaterials
025801
Yi Li and Yanlong Xu
By proposing a system composed of an array of bistable composite shells immersed in air, we develop a new class of periodic structure to control the propagation of sound. Through numerical investigation, we find that the acoustic band gap of this system can be switched on and off by triggering the snap through deformation of the bistable composite shells. The shape of cross section and filling fraction of unit cell can be altered by different number of bistable composite shells, and they have strong impact on the position and width of the band gap. The proposed concept paves the way of using the bistable structures to design a new class of metamaterials that can be enable to manipulate sound.
Semiconductors
025901
Ling Wang, Yan Zhang, Xiaojuan Li, Jing Xie, Jiqiang Wang and Xiangyang Li
Monolithic integrated solar blind devices on the GaN-based epilayer, which can directly readout voltage signal, were fabricated and studied. Unlike conventional GaN-based photodiodes, the integrated devices can finish those steps: generation, accumulation of carriers and conversion of carriers to voltage. In the test process, the resetting voltage was square wave with the frequency of 15 and 110 Hz, its maximal voltage of ∼2.5 V. Under LEDs illumination, the maximum of voltage swing is about 2.5 V, and the rise time of voltage swing from 0 to 2.5 V is only about 1.6 ms. However, in dark condition, the node voltage between detector and capacitance nearly decline to zero with time when the resetting voltage was equal to zero. It is found that the leakage current in the circuit gives rise to discharge of the integrated charge. Storage mode operation can offer gain, which is advantage to detection of weak photo signal.
025902
Bo Kong, Gao-Fu Liu and Ti-Xian Zeng
The electronic structures of REH3 (RE = Sm, Gd, Tb, Dy, Ho, Er, Tm, Lu) are extensively investigated using the parameter-free many-body perturbation GW calculations. The different symmetry hexagonal structures of REH3 almost present the same quasiparticle band structure both in the 4f-core and in the 4f-val cases. In the 4f-core case, the GGA + G0W0 calculations overestimate the direct band gap of the hexagonal structure; but the same G0W0 calculations in the cubic structure give a very suitable indirect band gap (around 1.9 eV). In the 4f-val case, for the hexagonal structure (GdH3), we find that the HSE03 calculations shift obviously the strongly localized 4f orbitals towards the high energy, and the shift is critical for the proper constructions and iterations of both G and W in the G0W/GW calculations of the electronic properties. In contrast to the cubic structure, the HSE03 calculations for the strong correlation of the localized 4f electrons in the hexagonal structure is not the critical factor for the acquirement of the appropriate band gap. The GGA + G0W0 calculations (GdH3) improve greatly the DFT band gap (0.2 eV) of the antiferromagnetic hexagonal structure and present a band gap with 1.0 eV; while the GGA + G0W0 calculations remove the small band overlap character (near Fermi level) of the ferromagnetic structure, and show a reasonable band gap with 1.5 eV at high symmetry Γ point. Therefore, to some extent, the GGA + G0W0 calculations can appropriately deal with the exchange-correlation interaction and the excited state in the ferromagnetic or antiferromagnetic hexagonal structure of GdH3.
025903
Ashu Wang, Lingyan Zeng and Wen Wang
025904
Nazia Erum and Muhammad Azhar Iqbal
Density functional theory (DFT) is employed to calculate the effect of pressure variation on electronic structure, elastic parameters, mechanical durability, and thermodynamic aspects of SrRbF3, in combination with Quasi-harmonic Debye model. The pressure effects are determined in the range of 0–25 GPa, in which cubic stability of SrRbF3 fluoroperovskite remains valid. Significant influence of compression on wide range of elastic parameters and related mechanical properties have been discussed, to utilize this material in low birefringence lens fabrication technology. Apart of linear dependence on elastic coefficients, transition from brittle to ductile behavior is also observed at elevated pressure ranges. Moreover, successful prediction of important thermodynamic aspects such as volume expansion coefficient (α), Debye temperature (θD), heat capacities (Cp and Cv) are also done within wide pressure and temperature ranges.
025905
Nikolay I Borgardt, Alexander V Rumyantsev, Roman L Volkov and Yuri A Chaplygin
Sputtering of the redeposited material was experimentally studied with the use of test structures specially prepared by the focused beam of gallium ions with different energies. The consequent milling of the structures and their characterization utilizing transmission electron microscopy revealed that the milling rate for the redeposited material is 1.3 times higher than for crystalline silicon. The dynamic Monte-Carlo simulations of sputtering were performed with the introduced discrete-continuous variation model for the surface binding energy of the silicon atoms, which takes into account the formation of the gallium precipitates in the surface layer of the bombarded material. The calculations allowed obtaining not only the correct values of redeposited material milling rate, but also the distributions of gallium atoms in the sputtered materials which were in the qualitative agreement with the experimental data.
025906
Xiaowei Wang, Jing Yang, Degang Zhao, Desheng Jiang, Zongshun Liu, Wei Liu, Feng Liang, Shuangtao Liu, Yao Xing, Wenjie Wang et al
Optical investigation was performed on InGaN/GaN multiple quantum well (MQW) structures grown by metalorganic chemical vapor deposition (MOCVD) with different temperatures. It is found that the emission intensity decreases abruptly when the growth temperature of InGaN QW decreases from 710 to 670 °C. The XRD measurements show that a poorer quality interface between the QW layers could decrease the emission quite a bit when the growth temperature is lower. In addition, due to the weakening surface mobility of adatoms, the localization states accompanied with defects are distributed more inhomogeneous at lower growth temperature, which is also responsible for the low emission intensity.
025907
Michał Wasiak, Marcin Motyka, Tristan Smołka, Jacek Ratajczak and Agata Jasik
In this paper, we present the results of a theoretical and experimental investigation into the refractive index and absorption, at room temperature, of a 4 μm-thick undoped epitaxial layer of GaSb deposited on a GaAs substrate. A theoretical formula for optical transmission through an etalon was derived, taking into account the finite coherence length of the light. This formula was used to analyse the measured transmission spectra. The refractive index was determined in a wide spectral range, between 0.105 eV and 0.715 eV. The absorption was determined for photon energies between 0.28 eV and 0.95 eV. An Urbach tail was observed in the absorption spectrum, as well as a constant increase in absorption in the spectral region above the band gap.
025908
Diego Velasco-Soto, Eduardo Menéndez-Proupin, Rebeca Realyvazquez-Guevara and José Andrés Matutes-Aquino
The electronic, vibrational and thermal properties of stoichiometric and non-stoichiometric cobalt antimonide CoSbx (x = 2.81, 2.875, and 3) are investigated by means of first principle calculations and thermal measurements. The molar heat capacity, electrical conductivity, and the electronic thermal conductivity are increased by the effect of Sb vacancies. Doping with Te and Ge also increases the electrical and thermal conductivity, suggesting that it can be used to enhance cobaltum antimonide as a thermoelectric material.
025909
Yifei Song, Tedi Kujofsa and John E Ayers
We present an approximate model for the threading dislocations in III–V heterostructures and have applied this model to study the defect behavior in metamorphic triple-junction solar cells. This model represents a new approach in which the coefficient for second-order threading dislocation annihilation and coalescence reactions is considered to be determined by the length of misfit dislocations, LMD, in the structure, and we therefore refer to it as the LMD model. On the basis of this model we have compared the average threading dislocation densities in the active layers of triple junction solar cells using linearly-graded buffers of varying thicknesses as well as S-graded (complementary error function) buffers with varying thicknesses and standard deviation parameters. We have shown that the threading dislocation densities in the active regions of metamorphic tandem solar cells depend not only on the thicknesses of the buffer layers but on their compositional grading profiles. The use of S-graded buffer layers instead of linear buffers resulted in lower threading dislocation densities. Moreover, the threading dislocation densities depended strongly on the standard deviation parameters used in the S-graded buffers, with smaller values providing lower threading dislocation densities.
Superconductors
026001
M Boubeche, Z L Lui, C Y Bai, Y Q Guo and C B Cai
In this work, Y1Dy0.5Ba2Cu3O7−δ (YDyBCO) + x% Dy2Ba1Cu1(Dy211)/Y1Dy0.5Ba2Cu3O7−δ (x = 0, 2, 4, 6, 8, 10) coated conductors with a film thickness about 1 μm were fabricated on buffered Hastelloy substrates by so-called super low fluorine metal organic deposition method. The effect of Dy211 on the bilayered doping on the texture, self field current density, critical temperature and flux pinning properties of YDyBCO films were investigated. With optimal Dy211 doping equal to 6 mol%, the properties of the resultant films are significantly enhanced.
Magnetic materials
026101
Zeynep Demir Vatansever and Ümit Akıncı
The nonequilibrium dynamic phase transition properties of a two dimensional FeC2 monolayer in the presence of a time dependent sinusoidally oscillating magnetic field have been studied by using both mean field approximation with Glauber type of stochastic process and Monte Carlo simulation technique. The variation of the Curie temperature of the system with the amplitude and period of the external magnetic field have been investigated and temperature dependence of the magnetization of the system is presented for selected external field parameters. Moreover, the dynamic hysteresis curves of the system have been obtained for a wide range of temperature. Numerical results of the present study indicate the controllability of the dynamic magnetic properties of two dimensional FeC2 sheet by amplitude and period of the external magnetic field.
026102
T Prabhakaran, R V Mangalaraja and Juliano C Denardin
In this report, cobalt ferrite nanoparticles synthesized using microwave assisted co-precipitation method was reported. Efforts have been made to control the particles size, distribution, morphology and magnetic properties of cobalt ferrite nanoparticles by varying the concentration of NaOH solution and microwave irradiation time. It was observed that the rate of nucleation and crystal growth was influenced by the tuning parameters. In that way, the average crystallite size of single phase cobalt ferrite nanoparticles was controlled within 9–11 and 10–12 nm with an increase of base concentration and microwave irradiation time, respectively. A narrow size distribution of nearly spherical nanoparticles was achieved through the present procedure. A soft ferromagnetism at room temperature with the considerable saturation magnetization of 58.4 emu g−1 and coercivity of 262.7 Oe was obtained for the cobalt ferrites synthesized with 2.25 M of NaOH solution for 3 and 7 min of microwave irradiation time, respectively. The cobalt ferrite nanoparticles synthesized with a shorter reaction time of 3–7 min was found to be advantageous over other methods that involved conventional heating procedures and longer reaction time to achieve the better magnetic properties for the technological applications.
026103
Junhua You and Yaozu Guo
One step synthesis of L10-FePt particles was reported in this paper. The particles were synthesized through high temperature spray pyrolysis. The as-synthesized particles were characterized by Transmitting Electron Microscopy (TEM), and corresponding results confirmed the polycrystalline and hollow structure of the products, with average size of ∼800 nm. The TEM Energy Dispersive x-ray (EDX) spectrum characterization showed that both Fe and Pt were homogenously distributed at nanoscale. The magnetic properties and crystal structure were investigated by Vibrating Sample Magnetometer (VSM) and x-ray Diffraction (XRD), respectively, and confirmed the high coercivity and L10 phase of the products. A post annealing was applied to the as-synthesized particles, and the results show that post annealing has little impact on the particle morphology, but could improve the magnetic properties.
026104
Homnath Luitel, Mahuya Chakrabarti, A Sarkar, S Dechoudhury, D Bhowmick, V Naik and D Sanyal
Room temperature magnetic properties of 50 keV N4+ ion beam implanted rutile TiO2 have been theoretically and experimentally studied. Ab-initio calculation under the frame work of density functional theory has been carried out to study the magnetic properties of the different possible nitrogen related defects in TiO2. Spin polarized density of states calculation suggests that both Ninst and NO can induce ferromagnetic ordering in rutile TiO2. In both cases the 2p orbital electrons of nitrogen atom give rise to the magnetic moment in TiO2. The possibility of the formation of N2 molecule in TiO2 system is also studied but in this case no significant magnetic moment has been observed. The magnetic measurements, using SQUID magnetometer, results a ferromagnetic ordering even at room temperature for the 50 keV N4+ ion beam implanted rutile TiO2.
026105
Bingbing Xu, Jiashuai Ma, Cong Fang, Meng Yao, Wenning Di, Xiaobing Li and Haosu Luo
In this work, we establish a dielectric loss model for multi-push-pull mode ME laminate composites. It deduces that the total dielectric loss of the ME composites equals the linear average of the dielectric loss of piezoelectric plate and epoxy resin. But further analysis of this model has indicated that we can ignore the dielectric loss of epoxy resin. To verify this model, we use three kinds of epoxy resin with different dielectric loss to fabricate multi-push-pull mode PMNT/Metglas ME laminate composites respectively. It turns out that the different kinds of epoxy resin have little influence on the total dielectric loss, capacitance and piezoelectricity of the composites, which demonstrates that our model conforms to the practical case. Therefore, we can pay more attention to the mechanical properties of epoxy resin rather than its dielectric loss on fabricating the ME laminate composites.
026106
Sajad Ahmad Dar, Vipul Srivastava, Umesh Kumar Sakalle, Adil Rashid and Gitanjali Pagare
Theoretical investigation on electronic structural, magnetic, mechanical and thermodynamic properties of SrPuO3 perovskite oxide has been accomplished within density functional theory (DFT). For exchange correlations generalized gradient approximation (GGA), on-site coulomb repulsion (GGA + U) and modified Becke-Johnson (mBJ) have been used. The calculated structural parameters including lattice constant were found in good agreement with the available experimental and theoretical results. The spin polarized electronic band structure and density of states present half-metallic nature for the compound with majority spin (spin up states) as metallic and minority spin (spin down states) as semi-conducting. The large value of magnetic moment equal to 4 μB was found for the compound. Elastic and mechanical properties have been predicted under ambient conditions. Moreover, thermodynamic parameters like Debye temperature (θD), specific heat (CV), entropy (S) etc have been calculated using quasi-harmonic Debye model under different temperature and pressure values.
026107
I Phebe Kokila, M Kanagaraj, P Sathish Kumar, Sebastian C Peter, C Sekar and Helen Annal Therese
Pervoskite manganite EuMnO3 synthesized by solid-state route was studied for their structural and magnetocaloric properties. EuMnO3 formed a single phase compound in orthorhombic crystal structure with a space group of Pbnm. The zero field cooling and field cooling magnetic responses exhibit an optimal Neel temperature (TN) of 57 K. A stronger magnetic coupling between the EuMnO3 particles are observed by a delay in reaching TN. The magnetocaloric effect analyzed extensively from the negative entropy (−ΔSm) change of 15.23 JKg−1K−1 for EuMnO3, exhibited a Relative Cooling Power (RCP) of ∼211 JKg−1 at 1.2 T proposing EuMnO3 as a potential magnetic refrigerant.
026108
Najam ul Hassan, Ishfaq Ahmad Shah, Abdur Rauf, Jun Liu, Yuanyuan Gong and Feng Xu
A comparative investigation on magnetostructural transformation and coupled magnetocaloric properties of Ni42Mn47.5Sn10.5 and Ni41.5Mn47.5Sn10.5Zn0.5 ferromagnetic shape memory alloys prepared by arc-melting method is carried out through structural and magnetic measurements. As Zn is doped in NiMnSn alloy, the cell volume decreases and the martensitic transformation temperature increases by 21 K. Obvious metamagnetic behavior and magnetic hysteresis is observed in isothermal magnetization curves, indicating the magnetic field induced magnetostructural transformation. Magnetic field induced phase transition is also confirmed under applied field of 2 T and martensitic transformation temperature is decreased by 4.1 and 5.29 K for Ni42Mn47.5Sn10.5 and Ni41.5Mn47.5Sn10.5Zn0.5 alloys, respectively. The entropy change in Ni41.5Mn47.5Sn10.5Zn0.5 alloy with change in magnetic field from 0 to 2 T is 12.3 J · kg−1 · K−1, which is larger than that in Ni42Mn47.5Sn10.5 alloy. The achieved low field entropy change in Zn doped alloy suggests its potential application as magnetic cooling refrigerant.
026109
Pengfei Yin, Yu Deng, Limin Zhang, Juan Huang, Huayao Li, Youhongyu Li, Yali Qi and Yu Tao
ZnO/Fe3O4/paraffin composites with good microwave absorption performance in low frequency band were prepared by physical blending technology. The morphology, phase structures, frequency-dependent electromagnetic and microwave absorbing properties of the composites were investigated. The results showed that the addition content of ZnO can adjust the microwave absorbing properties i.e. the position, intensity, and absorption bandwidth of composites, and the synergetic consequence of dielectric loss and magnetic loss is the main microwave absorption mechanism of the composites. The bandwidths with RL below −10 dB over different frequency ranges were obtained in the low frequency range of 0.5 ∼ 3 GHz at a thickness of 5 mm, e.g. 0.93 GHz from 1.59 to 2.52 GHz and 0.85 GHz from 1.26 to 2.11 GHz corresponding to the mass ratios of ZnO and Fe3O4 are 1:2 and 1:4, respectively. Thus, such absorbers can be applied as effective microwave absorbers in low frequency range of 0.5 ∼ 3 GHz.
Photonic materials
026201
Shriya Sinha, Manoj Kumar Mahata and Kaushal Kumar
The molybdate compounds as luminescent medium have received great attention of recent research due to their excellent intrinsic optical properties. Therefore, the investigation on the optical thermometry and nanoheating effect in Er3+–Yb3+ doped molybdates of yttrium (EYYMO), gadolinium (EYGMO) and lanthanum (EYLMO) nanophosphors is reported herein. The temperature dependent fluorescence intensity ratio of green (525 and 548 nm) emission bands of Er3+ ions were analyzed within 300–500 K temperature range to determine the thermal behavior. The comparative temperature sensitivity of the materials has been found to depend on the phonon energy of their own. The thermal sensitivity is higher in the materials with low phonon energy. The intensity ratio of the green emission bands has been found to alter with the laser excitation density, which can be used to estimate the induced temperature in the materials. Furthermore, the photothermal conversion efficiency is calculated in the water dispersed samples and the maximum photothermal conversion efficiency of 49.6% is achieved for EYGMO nanophosphor. Comparative experimental results explore unequal thermal sensing and induced optical heating in the three rare earth molybdates. The optical properties of the green emitting molybdates are interesting for temperature sensing and optical heating applications.
026202
Yan Zhang, Jiayue Xu, BoBo Yang, Qinzhi Cui and Tian Tian
A series of Bi4Si3O12: xEu3+ (0.01 ≤ x ≤ 0.1) continuous solid solution phosphors were explored as novel red-emitting phosphors for white light LED. Bi4Si3O12: xEu3+ phosphors with cubic eulytite structure were prepared by solid-state reaction. The effect of doping concentration on excitation, luminescence spectra, the decay curves and CIE color coordinate of the Eu3+-doped Bi4Si3O12 phosphors were analyzed. We analyzed the dependence of emission intensity on dopant concentration through Van Uitert’s equation simulation. It is identified that the dipole—dipole interaction plays a major role in the mechanism of energy migration of Eu3+ in Bi4Si3O12 phosphor. The critical distance for energy migration was determined to be 19 Å. The self-generated quenching process of Eu3+ in the phosphor was discussed based on the model of self-quenching lifetime in presence of self-trapping. The CIE chromaticity coordinates of the phosphor shift to a pure red region with increase of Eu3+ content.
026203
Yao Guo, Chengbo Li, Yuanbin Xue, Cuihuan Geng and Dayong Tian
The poor stability of organometallic halide perovskite in humid environments is one of the biggest challenges for its commercialization in light harvesting and electroluminescent displays. Understanding the atomic detail of the perovskite/water (oxygen) interface is a critical way to explore the practicability of perovskite. In this work, we report a density functional study of water and oxygen adsorption on the Cs/Rb incorporated FAPbI3 (001) surface. The role played by water and oxygen molecules has been extensively studied in the initial degradation processes, where the strong interactions between adsorbates and perovskite surfaces are confirmed. Our results show that the dopant-terminated surface was relatively more stable than PbI2-termination one. The effects of doping on the optoelectronic properties were slight at low concentrations. The calculations showed that the molecule tend to adsorb on the I-top site of the Cs-terminated surface and the Pb-top site of the PbI2 (Cs)-terminated surface. The vdW contribution on the bonding between bare surface and molecule can be observed. The degradation-induced optical absorption decrease in the visible region could be found. Water and oxygen molecule destroy the perovskite surface structures and subsequently reduce its conversion efficiency. These findings contribute molecular-level insight into the initial stage of perovskite degradation, which should be helpful to inspire new interfacial modifications to improve the stability of corresponding perovskite materials under wet conditions.
026204
Ji Li and Y J (Bill) Yang
New type of ternary NiAlCe layered double hydroxide photocatalyst was synthesized by a simple hydrothermal reaction. The obtained photocatalyst shows efficient visible-light activity for CO2 reduction to CH4. We have investigated the optimal Ce content in the catalyst and analyzed the mechanism by materials characterization. Additionally, a novel alkali etching method was used to construct the porous structure. The effect of the porosity and morphologies on the activity is investigated. It is found that the ternary NiAlCe layered double hydroxide photocatalyst with porosity showing the best photocatalytic activity among all the samples. Based on the characterization and first principle calculation, the detailed photocatalytic mechanism of the ternary NiAlCe layered double hydroxide photocatalyst is deduced.
026205
S R Balaji, T Balu and T R Rajasekaran
Single crystals of Bis (glycine) Strontium Chloride (BGSC) were grown by means of slow evaporation process by using analar grade Glycine and Strontium Chloride Hexahydrate as a parent compound from its aqueous solution at room temperature. The final chemical composition,
formed were metallic light colorless block, about the size of 28 mm × 9 mm × 8 mm. A single-crystal x-ray diffraction study revealed an ordered superstructure with orthorhombic symmetry that could be assigned to the space group Pbcn. The structure in BGSC, revealed in the electron density distribution was analyzed by the direct methods (SHELXS-2014) and refined by least squares full matrix method (SHELXL-2014). The crystal structure, including anisotropic atomic displacement parameters for each atom and isotropic atomic displacement parameters for hydrogen atom, was refined to R1 = 0.0395, wR2 = 0.0776 using 1097 independent reflections. The FTIR spectrum of BGSC confirms the protonation of amino groups and the different molecular groups present in BGSC vibrate in different modes. Reverse Indentation Size Effect (RISE) was revealed in BGSC in the micro-hardness analysis using Vicker’s micro-hardness analysis. DTA and DSC results ruled out the possibility of structural change independent of mass change. The AFM studies shows fine nano size fiber like structure of the grown crystals.
Electronic materials
026301
Prashant Singh, Rajesh Kumar Jha, Rajat Kumar Singh and B R Singh
We report the integration of multilayer ferroelectric film deposited by RF magnetron sputtering and explore the electrical characteristics for its application as the gate of ferroelectric field effect transistor for non-volatile memories. PZT (Pb[Zr0.35Ti0.65]O3) and SBN (SrBi2Nb2O9) ferroelectric materials were selected for the stack fabrication due to their large polarization and fatigue free properties respectively. Electrical characterization has been carried out to obtain memory window, leakage current density, PUND and endurance characteristics. Fabricated multilayer ferroelectric film capacitor structure shows large memory window of 17.73 V and leakage current density of the order 10−6 A cm−2 for the voltage sweep of −30 to +30 V. This multilayer gate stack of PZT/SBN shows promising endurance property with no degradation in the remnant polarization for the read/write iteration cycles upto 108.
026302
Yefeng Feng, Yanmin Dai, Jingjing Sun, Jianbing Hu and Cheng Peng
Interface induced polarization has been proved to have a great impact on dielectric features of 2-2 series composites containing Si-based semi-conducting sheet and polymer layer. In those 2-2 composites, the obviously increased high permittivity of Si-based ceramic sheet was confirmed to be responsible for the measured high permittivity of composites. Interface interaction was found to come from strong electrostatic pull of high polarity polymer layer and induced high polarity of Si-based ceramic sheet. In this work, the similar interface interaction was utilized to obtain the desired promising 2-2 series composite dielectrics made from ultra-high polarity anti-ferroelectric ceramic sheet and high polarity fluoropolymer layer. Based on compositing, the obviously elevated high permittivity detected in polymer layer was found to strongly contribute to tested high permittivity in resulting composites. In this case, interface induced polarization should come from a very large electrostatic pull of ceramic sheet (ultra-high polarity ionic dipoles) and elevated high induced polarity of polymer layer (high polarity covalent dipoles). Dielectric and conductive properties of two designed 2-2 composites have been detailedly researched. Reduced total inborn polarity of ceramic sheet was found to lead to a maintained high permittivity, lowered dielectric loss and decreased conductivity in resulting composite. This work might provide a facile route to obtain the desired composite dielectrics with promising comprehensive electric properties based on interface effect in 2-2 composites.
026303
Najla M Khusayfan, A F Qasrawi and Hazem K Khanfar
In the current work, a tunneling barrier device made of 20 nm thick Sb2Te3 layer deposited onto 500 nm thick CdS is designed and characterized. The design included a Yb metallic substrate and Ag point contact of area of 10−3 cm2. The heterojunction properties are investigated by means of x-ray diffraction and impedance spectroscopy techniques. It is observed that the coating of the Sb2Te3 onto the surface of CdS causes a further deformation to the already strained structure of hexagonal CdS. The designed energy band diagram for the CdS/Sb2Te3 suggests a straddling type of heterojunction with an estimated conduction and valence band offsets of 0.35 and 1.74 eV, respectively. In addition, the analysis of the capacitance-voltage characteristic curve revealed a depletion region width of 14 nm. On the other hand, the capacitance and conductivity spectra which are analyzed in the frequency domain of 0.001–1.80 GHz indicated that the conduction in the device is dominated by the quantum mechanical tunneling in the region below 0.26 GHz and by the correlated barrier hopping in the remaining region. While the modeling of the conductivity spectra allowed investigation of the density of states near Fermi levels and an average scattering time of 1.0 ns, the capacitance spectra exhibited resonance at 0.26 GHz followed by negative differential capacitance effect in the frequency domain of 0.26–1.8 GHz. Furthermore, the evaluation of the impedance and reflection coefficient spectra indicated the usability of these devices as wide range low pass filters with ideal values of voltage standing wave ratios.
026304
Li Yang, Lu Zhu, Yaocheng Zhang, Shiyuan Zhou, Yifeng Xiong and Pengcheng Wu
The microstructural evolution and IMCs growth behavior of Sn-58Bi and Sn-58Bi-0.25Mo solder joints were investigated. The results showed that the microstructure is coarsened, the IMCs layer thickness is increased and the tensile strength of Sn-58Bi and Sn-58Bi-0.25Mo solder joints is decreased with increasing aging time and temperature. Aging temperature is the key factor that causes the excessive IMCs growth of the solder joint compared with aging time, and the activation energy of IMCs layer growth of Sn-58Bi and Sn-58Bi-0.25Mo solder joints is 48.94 kJ mol−1 and 53.79 kJ mol−1, respectively. During the aging treatment, the microstructure of Sn-58Bi solder joint is refined by adding Mo nanoparticles, and the appropriate IMCs layer thickness and improved mechanical properties are obtained by Sn-58Bi-0.25Mo solder joint.
Thin films
026401
D M Sedlovets, M V Shuvalov, I I Khodos, O V Trofimov and V I Korepanov
Polyphthalocyanines (PPCs) are a unique class of two-dimensional polymers. Like graphene, they possess a 2D-conjugated electronic system, but in contrast to graphene, PPCs have finite band gap, pronounced magnetic properties and high catalytic activity. The applications of PPCs however are hindered by the difficulty to obtain a material of high polymerization degree and structural uniformity. Among PPCs, a metal-free one (H2PPC) is of particularly high interest from both fundamental and applied viewpoints, because the two hydrogen atoms could be substituted by a variety of metals. H2PPC therefore can be considered as a ‘universal polyphthalocyanine matrix’. In this work, we develop a technique for a chemical deposition of thin films of H2PPC on a catalyst-doped surface. High polymerization degree and structural uniformity of the films are confirmed by TEM and FTIR. Raman spectroscopy corroborates the presence of 2D conjugated structure.
026402
M Rashad and A A A Darwish
Thermally evaporated films of promised vanadyl 2,3-naphthalocyanine (VONc) materials were prepared. Both structural and optical properties of VONc films were monitored before and after annealing at different annealing temperatures of 423, 473 and 523 K. The structural properties were investigated by x-ray diffraction and scanning electron microscopy which showed an agglomerated grains under annealing effect. The transmittance and reflectance of the VONc films were detected as a function of wavelength in the range 200–2500 nm at those annealing temperatures. Linear and nonlinear optical properties of these films were studied under thermal effect. Varies interesting optical investigations were observed for these VONc films which develop their optoelectronic applications. A blue shift of the optical band gap of the investigated films with annealing temperatures is observed. Two different energy gaps appear in the range of 1.25–1.5 eV, and at the range of 2.5–2.75 eV. The third-order nonlinear optical susceptibility showed a decreasing dependence with the annealing temperatures due to its local field. Three promising maximum optical conductivity energies were observed.
026403
Reza Mohammadigharehbagh, Suat Pat, Caner Musaoglu, Şadan Korkmaz and Soner Özen
Cr doped ZnO thin films were prepared onto glass and polyethylene terephthalate (PET) substrates using thermionic vacuum arc. XRD patterns show the polycrystalline nature of the films. Cr, Zn, ZnO and Cr2O3 were detected in the layers. The mean crystallite sizes of the films were calculated about 20 nm for the films onto glass and PET substrates. The maximum dislocation density and internal strain values of the films are calculated. According to the optical analysis, the average transmittance and reflectance of the films were found to be approximately 53% and 16% for glass and PET substrates, respectively. The mean refractive index of the layer decreased to 2.15 from 2.38 for the PET substrate. The band gap values of the Cr-doped ZnO thin films were determined as 3.10 and 3.13 eV for glass and PET substrates.
026404
Yihe Miao, Peng Du, Zhiyu Wang, Qianli Chen and Morteza Eslamian
This work focuses on the development of nearly annealing-free ZnO-based perovskite solar cells (PSCs), suitable for low-cost manufacturing of PSCs on flexible substrates. To this end, thin film of ZnO nanoparticles is employed as the electron transporting layer (ETL), because of its low-temperature solution-processability and high electron mobility. In order to remove the structural and surface defects, ultrasonic vibration is imposed on the substrate of the as-spun wet ZnO films for a short duration of 3 min. It is shown that the ultrasonic excitation bridges the ZnO nanoparticles (cold sintering), and brings about significant improvement in the ZnO film nanostructure and functionality. In addition, ethyl acetate (EA), as an emerging volatile anti-solvent, is employed to deposit the methylammonium (MA) lead halide perovskite thin film atop the ZnO ETL, in order to prepare perovskite layers that only need an annealing time of 30 s. The ZnO-based PSCs, with a simple structure and free of additional treatments, except for the ultrasonic vibration, exhibit a promising performance with a power conversion efficiency (PCE) of over 11%, 40% higher than that of the control device. The ultrasonic vibration treatment is facile, low-cost, environmentally friendly, and compatible with the scalable coating and printing techniques, such as spray and blade coating.
026405
Silvia Sizuka Oishi, Lilian Mieko Silva, Edson Cocchieri Botelho, Mirabel Cerqueira Rezende, Carlos Alberto Alves Cairo and Neidenêi Gomes Ferreira
Boron doped ultrananocrystalline diamond (B-UNCD) growth was studied on modified reticulated vitreous carbon (RVC) produced from poly(furfuryl alcohol) (PFA) resin with sodium hydroxide additions at two different heat treatment temperatures. The different amounts of NaOH in PFA (up to reaching pH values of around 3, 5, 7, and 9) aimed to neutralize the acid catalyst and to increase the PFA storage life. Besides, this procedure was responsible for increasing the oxygen content of RVC samples. Thus, the effect of carbon and oxygen coming from the substrates in addition to their different graphitization indexes on diamond morphology, grain size, preferential growth and boron doping level were investigated by FEG-SEM, x-ray diffraction and Raman spectroscopy. Therefore, B-UNCD films were successfully grown on RVC with pH values of 3, 5, 7, and 9 heat treated at 1000 and 1700 °C. Nonetheless, the higher oxygen amount during B-UNCD growth for samples with pH 7 and 9 heat treated at 1000 °C was responsible for the RVC surface etching and the decrease in the boron concentration of such samples. The cross section images showed that B-UNCD infiltrated at around 0.9 mm in depth of RVC samples while carbon nanowalls were observed mainly on RVC samples heat treated at 1000 °C for all pH range studied.
026406
Shengchi Bai, Haifeng Wang, Hui Yang, He Zhang and Xingzhong Guo
Silver nanowires (AgNWs)-polyurethane (PU) composite transparent conductive films were fabricated via transfer method using AgNWs conductive inks and polyurethane as starting materials, and the effects of post-treatments including heat treatment, NaCl solution bath and HCl solution bath for AgNWs film on the sheet resistance and transmittance of the composite films were respectively investigated in detail. AgNWs networks are uniformly embedded in the PU layer to improve the adhesion and reduce the surface roughness of AgNWs-PU composite films. Heat treatment can melt and weld the nanowires, and NaCl and HCl solution baths promote the dissolution and re-deposition of silver and the dissolving of the polymer, both which form conduction pathways and improve contact of AgNWs for reducing the sheet resistance. Smooth and flexible AgNWs-PU composite film with a transmittance of 85% and a sheet resistance of 15 Ω · sq−1 is obtained after treated in 0.5 wt% HCl solution bath for 60 s, and the optoelectronic properties of the resultant composite film can maintain after 1000 cycles of bending and 100 days.
026407
G P Cao and R G Song
Micro-arc oxidation (MAO) ceramic coatings were prepared in silicate-based electrolyte on 7075 aluminum alloy. The effects of current density on microstructure and properties of the MAO coatings were studied by scanning electron microscopy (SEM), stereoscopic microscopy, x-ray diffraction (XRD), electrochemical tests as well as tribological and wear tests. The results showed that the current density plays an important role in affecting the quality of the MAO coatings. XRD results showed that the α-Al2O3 phase first increased then decreased with increasing the current density, which matched well with the micro-hardness test and the wearing test results. On the other hand, the coalescent strength measurements revealed that the coating prepared at the current density of 12 A dm−2 is of the highest adhesion force. The potentiodynamic polarization test proved that the coating obtained under 10 A dm−2 exhibits the best corrosion resistance, which is directly related to the morphology of coating.
026408
Tang-Yu Lai, Kuan-Yu Wang, Te-Hua Fang and Chao-Chun Huang
Bismuth telluride (Bi2Te3) is a type of thermoelectric material used for energy generation that does not cause pollution. Increasing the thermoelectric conversion efficiency (ZT) is one of the most important steps in the development of thermoelectric components. In this study, we use molecular dynamics to investigate the mechanical properties and thermal conductivity of quintuple layers of Bi2Te3 nanofilms with different atomic arrangements at the interface and study the effects of varying layers, angles, and grain boundaries. The results indicate that the Bi2Te3 nanofilm perfect substrate has the ideal Young’s modulus and thermal conductivity, and the maximum yield stress is observed for a thickness of ∼90 Å. As the interface changed, the structural disorder of atomic arrangement affected the mechanical properties; moreover, the phonons encounter lattice disordered atomic region will produce scattering reduce heat conduction. The results of this investigation are helpful for the application of Bi2Te3 nanofilms as thermoelectric materials.
026409
Fekadu Gashaw Hone and F B Dejene
Polycrystalline lead sulphide (PbS) thin films were grown on glass substrates by chemical bath deposition route using ethanolamine (ETA) as a complexing agent. The effects of ETA molar concentration on the structural, morphological, electrical and optical properties of lead sulphide thin films were thoroughly studied. The XRD analyses revealed that all the deposited thin films were face center cubic crystal structure and their preferred orientations were varied along the (111) and (200) planes. The XRD results further confirmed that ETA concentration had a significant effects on the strain, average crystalline size and dislocation density of the deposited thin films. The SEM studies illustrated the evolution and transformation of surface morphology as ETA molar concentration increased from 0.41 M to 1.64 M. The energy dispersive x-ray analysis was used to verify the compositional elements of the deposited thin films. Optical spectroscopy investigation established that the band gap of the PbS thin films were reduced from 0.98 eV to 0.68 eV as ETA concentration increased. The photoluminescence spectra showed a well defined peak at 428 nm and shoulder around 468 nm for all PbS thin films. The electrical resistivity of the thin films found in the order of 103 Ω cm at room temperature and decreased as the ETA molar concentration was increased.
026410
Pranay Bagde, S G Sapate, R K Khatirkar, Nitesh Vashishtha and Satish Tailor
Cr2O3-25TiO2 coating was deposited by atmospheric plasma spray (APS) coating technique. Effect of load (5–30 N) and sliding velocity (0.25, 0.75 m s−1) on friction coefficient and abrasive wear behaviour of the Cr2O3-25TiO2 coating was studied. Mechanical and microstructural characterization of the Cr2O3-25TiO2 coating was carried out. With an increase in sliding velocity, abrasive wear rate and friction coefficient (COF) decreased while wear rate and friction coefficient showed an increasing trend with the load. The worn out surfaces were analyzed by SEM, EDS and XRD. At lower sliding velocity, XRD analysis revealed peaks of Ti2O3, Ti3O5, CrO2 and CrO3. In addition, peak of Ti4O7 was also detected at higher sliding velocity and at 30 N load. At higher sliding velocity medium to severe tribo oxidation was observed. XPS analysis of worn surfaces at both the sliding velocities, showed surface film of oxides of titanium and chromium along with Cr(OH)3. Magneli phase titanium oxides with sub stoichiometric composition, along with surface films of chromium oxides and hydroxides altered the friction and wear behaviour of the coating. The decrease in friction coefficient with an increase in sliding velocity was attributed to tribo oxides and tribochemical reaction films having lower shear strength with good lubricating properties. The mechanism of material removal involved plastic deformation at lower load whereas inter-granular and trans-granular fracture, delamination cracking and splat fracture was observed with an increase load from 10 N to 30 N.
026411
Dong Tianshun, Zhou Xiukai, Li Guolu, Liu Li and Wang Ran
Ni based coatings were prepared on steel substrate by means of plasma spraying, and were remelted by TIG (tungsten inert gas arc) method subsequently. The microstructure, microhardness, electrochemical corrosion and corrosive wear resistance under PH = 4, PH = 7 and PH = 10 conditions of the coatings before and after remelting were investigated. The results showed that the TIG remelting obviously reduced the defects and dramatically decreased the coating’s porosity from 7.2% to 0.4%. Metallurgical bonding between the remelted coating and substrate was achieved. Meanwhile, the phase compositions of as-sprayed coating were γ-Ni, Mn5Si2 and Cr2B, while the phase compositions of the remelting coating were Fe3Ni, Cr23C6, Cr2B and Mn5Si2. The microhardness of the coating decreased from 724 HV to 608 HV, but the fracture toughness enhanced from 2.80 MPa m1/2 to 197.3 MPa m1/2 after remelting. After corrosive wear test, the average wear weight loss and 3D morphology of wear scar of two coatings indicated that the wear resistance of the remelted coating was remarkably higher than that of as-sprayed coating. Therefore, TIG remelting treatment was a feasible method to improve the coating’s microstructure and enhance its corrosive wear resistance.
026412
G Rajesh, N Muthukumarasamy, Dhayalan Velauthapillai, Kallol Mohanta, V Ragavendran and Sudip K Batabyal
CdZnTe thin films were fabricated on glass substrates by sputtering and the potentiality of photoinduced electrical data storage was investigated. As deposited film was annealed to enhance the crystallization and both the as deposited and annealed films were characterized by XRD, RAMAN, UV–vis-NIR, PL, FESEM and EDAX analysis. Optical and electrical properties of the films were investigated in detail. The thin films show interesting photo induced electrical bistability. The electrical bistability was observed with symmetric lateral electrodes under illuminated condition only. In the dark, forward and reverse bias curves traced the same path but under light illumination condition there is a substantial difference in the I–V traces of the forward and reversed biased conditions. After annealing the crystallinity of the as deposited film improved and the ON-OFF ratio of electrical bistability increased considerably. This phenomenom could be useful for light sensitive RAM type devices.
026413
E Kheirandish, T Hosseini, N Yavarishad, S King and N Kouklin
The current study presents the synthesis and characterization of poly-crystalline TiO2 thin-film prepared by rf-sputtering on top of a highly regimented nanoporous Au-coated Al2O3 substrate. The film’s physical and electronic properties were characterized via SEM, EDS, x-ray diffraction and RAMAN spectroscopy as well as temperature dependent photoluminescence (PL) and I–V measurements. The films feature a 1D, columnar-like structure and exhibit a medium strength, spectrally-broad light emission in the UV–visible range. PL emission shows a weak T-dependence and is attributed to interband electronic transitions and defect-assisted radiative recombinations. The charge transport is confirmed to be polaronic in nature with both thermally-assisted hopping and quantum mechanical tunneling regulating a charge flow within the columns in the intermediate temperature regime of ∼200–320 K. These results open a door to utilizing nano-textured substrates/scaffolds to produce electronic-grade anatase TiO2 by sputtering for advanced opto-electronic device applications.
026414
Augustine Chukwuemeka and Nnamdi Nnabuchi Mishark
Optical and solid state characteristics of novel CuO/PbS double layer thin films were studied. Rutherford backscattering (RBS) technique deciphered the thicknesses of the films as 650 nm, 471 nm and 482 nm for as-deposited, annealed at 473 K and 673 K respectively. The XRD analysis depicts increase in grain size and peak intensity as temperature increases. The results of optical characterization show that thermal annealing has profound effects on all the optical and solid state parameters investigated. The absorbance increased with increase in temperature exhibiting maximum for the film annealed at 673 K. The transmittance of the film samples showed a decreasing trend with increase in temperature exhibiting minimum for the film annealed at 673 K. The absorption coefficient increases from 0.001 × 106 m−1 to 0.006 × 106 m−1 for as-deposited, 0.0025 × 106 m−1 to 0.0175 × 106 m−1 for the annealed at 473 K and 0.003 × 106 m−1 to 0.020 × 106 m−1 for the annealed at 673 K. The extinction coefficient increased with increased in temperature exhibiting a maximum for the film annealed at 673 K. The refractive index, real and imaginary dielectric constant do not have a trend with increase in annealing temperature. Increase in annealing temperature lowers the band gap from 4.13 eV for the as-deposited to 4.05 eV and 3.90 eV for the annealed at 473 K and 673 K respectively. The wide- bandgap materials permits devices to operate at much higher voltages, frequencies and temperatures than convection semiconductor materials. Thus, this film could be used for high power applications, light-emitting diodes, transducers and window layers for solar cell fabrication.
026415
Yangsen Hu, Zhenghua Wu, Fengjie Ye and Zhiyu Hu
The manoeuvre of thermal transport property across multilayer films with inserted metal layers through controlling the metal-nonmetal interfaces is of fundamental interest. In this work, amorphous Si/Si0.75Ge0.25 multilayer films inserted with varying Au layers were fabricated by magnetron sputtering. The structure and sharp interface of multilayers films were characterized by low angle x-ray diffraction (LAXRD), grazing incidence small angle x-ray scattering (GISAXS) and scanning electron microscopy (SEM). A differential 3ω method was applied to measure the effective thermal conductivity. The measurements show that thermal conductivity has changed as varying Au layers. Thermal conductivity increased from 0.94 to 1.31 Wm−1K−1 while Si0.75Ge0.25 layer was replaced by different Au layers, which was attributed to the strong electron-phonon coupling and interface thermal resistance in a metal-nonmetal multilayered system. Theoretical calculation combined with experimental results indicate that the thermal conductivity of the multilayer film could be facilely controlled by introducing different number of nanoconstructed metal-nonmetal interfaces, which provide a more insightful understanding of the thermal transport manipulation mechanism of the thin film system with inserting metal layers.
026416
Jyoti Shah, Priyanka Bhatt, K Diana Diana Dayas and R K Kotnala
Inversion of BaTiO3 and GdFeO3 thin films in bilayer configuration has been deposited by pulsed laser deposition technique. A significant effect of strain on thin film has been observed by X-ray diffraction analysis. Tensile strain of 1.04% and 0.23% has been calculated by X-ray diffraction results. Higher polarization value 70.4 μC cm−2 has been observed by strained BaTiO3 film in GdFeO3/BaTiO3 bilayer film. Strained GdFeO3 film in BaTiO3/GdFeO3 bilayer configuration exhibited ferromagnetic behaviour showed maximum magnetization value of 50 emu gm−1. Magnetoelectric coupling coefficient of bilayer films have been carried out by dynamic method. Room temperature magnetoelectric coupling 2500 mV cm−1-Oe has been obtained for BaTiO3/GdFeO3 bilayer film. The high ME coupling of the BaTiO3/GdFeO3 bilayer film reveals strong interfacial coupling between ferroelectric and ferromagnetic dipoles. On magnetoelectric coupling coefficient effect of ferromagnetic GdFeO3 layer has a significant role. Such high value of ME coupling may be useful in realization of magnetoelectric RAM (MeRAM) application.
026417
Hom Kandel, Tar-Pin Chen and Zhongrui Li
In this study, the electronic transport and Raman spectroscopic properties of Fe-doped (110) PrBa2Cu3 O7 (PBCFO) epitaxial thin films were systematically investigated. The thin films were deposited on (110) LAO single crystal substrates using pulsed laser deposition (PLD) technique with KrF excimer laser of energy density equivalent to 1.0 J cm−2. The Electrical resistivity of the (110) PBCFO thin film increased by a factor of 47 at 77 K and the electronic transport on these films was via Mott’s three-dimensional variable range hopping mechanism among the localized electronic states. The activation energies of the (110) PBCFO thin films were calculated to be 160 meV at 300 K and 70 meV at 77 K respectively, suggesting that the hopping was mainly thermally assisted. The Raman spectroscopy measurement revealed a Raman mode at ∼600 cm−1 indicating the substitution of Cu by Fe at the Cu-O chain site of the PrBa2Cu3O7 (PBCO). The partial substitution of the Cu by the Fe induced disorder and localization of the charge carriers at the Cu-O chain sites, thereby increasing the electrical resistivity of the (110) PBCO thin film.
026418
Sivanantham Nallusamy and Gopalakrishnan Nammalvar
Enhancement of ferromagnetism in Mn doped ZnO thin films by surface functionalization using dodecane thiol is reported. The Mn doped (5, 10 and 15 mol%) ZnO films grown by Radio Frequency (RF) Magnetron Sputtering have been functionalized using dodecane thiol by spin coating technique. The unfunctionalized and surface functionalized Mn doped ZnO thin films have been examined by x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), photoluminescence (PL), atomic force microscopy (AFM) and vibrating sample magnetometer (VSM) measurement. From XRD, it has been observed that all films are oriented along (002) plane. The XRD pattern reveals that no significant change in intensity of (002) peak upon surface functionalization with dodecane thiol. However, slight shift in (002) peak upon Mn doping due to lattice strain has been observed. The PL spectra of Thiol capped Mn doped ZnO thin films shows quenching of visible emission intensity relative to the unfunctionalized Mn doped ZnO thin films. The quenching of visible emission indicates that thiol passivates surface defects via Zn-S bonding. The saturation magnetization of Mn doped ZnO thin film was found to increase by 18% upon thiol functionalization. This enhanced ferromagnetic material can be used in fabrication of GMR devices.
026419
A Delgado, Y Guerra, E Padrón-Hernández and R Peña-Garcia
Combining the sol gel method and spin coating technique, yttrium iron garnet (YIG) films were obtained on silicon (Si) substrate. Four YIG films with different thicknesses were fabricated to achieve low FMR linewidth. The x-ray diffraction has shown a single phase, belonging to the cubic structure of the YIG, while the morphology of the films has presented small pores and some grains on the surface. The FMR linewidth of the YIG films decreased 110 Oe, 108 Oe, 93 Oe and 71 Oe as the film thickness increased 134 nm, 246 nm, 376 nm and 489 nm, respectively. This result indicates that high-quality YIG films can be achieved on Si substrates, controlling the thickness. The sol gel method is shown as a very economical and easy alternative to obtain YIG films with low FMR linewidth, which may be important for making microwave integrated devices.
Metals and alloys
026501
Hao Wan, Naichao Si, Quan Wang and Zhenjiang Zhao
Morphology variation, composition alteration and microstructure changes in 1060 aluminum irradiated with 50 keV helium ions were characterized by field emission scanning electron microscopy (FESEM) equipped with x-ray elemental scanning, 3D measuring laser microscope and transmission electron microscope (TEM). The results show that, helium ions irradiation induced surface damage and Si-rich aggregates in the surfaces of irradiated samples. Increasing the dose of irradiation, more damages and Si-rich aggregates would be produced. Besides, defects such as dislocations, dislocation loops and dislocation walls were the primary defects in the ion implanted layer. The forming of surface damages were related with preferentially sputtering of Al component. While irradiation-enhanced diffusion and irradiation-induced segregation resulted in the aggregation of impurity atoms. And the aggregation ability of impurity atoms were discussed based on the atomic radius, displacement energy, lattice binding energy and surface binding energy.
026502
Magdalena Galatanu, Monica Enculescu and Andrei Galatanu
The divertor of a fusion reactor like DEMO requires materials able to withstand high heat fluxes and neutron irradiation for several years. For the water cooling concept of this essential part of the reactor, the most likely plasma facing material will be W, while the heatsink material considered is CuCrZr or an improved version of such a Cu-based alloy. To realize W–Cu alloy joints able to withstand thousands of thermal cycles can be difficult due to the difference between the thermal expansion coefficients of these materials. In this work we investigate the possibility to realize such joints by using W–Cu functional gradient materials (FGMs) produced from nanometric and micrometric metallic powders mixtures and consolidated by spark plasma sintering at about 900 °C. Morphological and thermal properties investigations, performed for typical compositions, shows that the best results are obtained using powders with micrometric dimensions. A resulting 1 mm thick, 3 layers W–Cu FGM produced by this simple method shows a remarkable almost constant thermal conductivity value of 200 W m−1 K−1, from room temperature up to 1000 °C.
026503
Jianbo Sun, Liying Yang, Wei Liu and Minxu Lu
The electrochemical characteristics and localized corrosion of X65 steel were investigated in CO2-saturated brines as a function of salt concentration employing electrochemical techniques and immersion tests. The results show that, as salt concentration increases, the corrosion mechanism changes from electrochemical steps control to the mixed control of mass transfer and electrochemical steps. The higher the salt concentration is, the more obvious the mass transfer control will be. The corrosion rate firstly increases and then decreases with salt content. There is a maximum corrosion rate somewhere between 60 and 120 g l−1 salt content. The salting-out effect may play a crucial role in steel corrosion in CO2-bearing systems with higher salt concentrations. Chloride ions account for the decrease of the surface layer thickness and make them non-adherent, thereby promoting the initiation and development of localized corrosion at salt concentration above 120 g l−1.
026504
Shuhaib Mushtaq and M F Wani
Solid lubricants are particularly used in the advanced mechanical motion systems with extreme conditions such as (high temperature, vacuum, radiation, extreme contact pressure, etc). The main focus of this paper is to study the dry sliding friction and wear behavior of Fe-Cu-Sn alloy with varying wt% of graphite at high temperature up to 423 K. The influence of temperature, sliding distance and load on friction and wear behavior of Fe-Cu-Sn alloy against EN8 steel was studied using ball (EN8) on disc (Fe-Cu-Sn alloy). Lower wear and lower friction of Fe-Cu-Sn alloy were observed at high temperature, as compared to room temperature. Surface morphological and surface analytical studies of fresh and worn surfaces were carried out using optical microscopy, 3D profilometer, scanning electron microscope, energy dispersive x-ray spectroscopy, XRD, and Raman spectroscopy to understand the friction and wear behavior.
026505
Luobei Zhu, Jianli He and Ying Zhang
In order to clarify the competition between work hardening (WH) caused by dislocation movements and the dynamic softening result from dynamic recovery (DRV) and dynamic recrystallization (DRX), a new two-stage flow stress model of X12CrMoWVNbN10-1-1 (X12) ferrite heat-resistant steel was established to describe the whole hot deformation behavior. And the parameters were determined by the experimental data operated on a Gleeble-3800 thermo- mechanical simulation. In this constitutive model, a single internal variable dislocation density evolution model is used to describe the influence of WH and DRV to flow stress. The DRX kinetic dynamic model can express accurately the contribution of DRX to the decline of flow stress, which was established on the Avrami equation. Furthermore, The established new model was compared with Fields-Bachofen (F-B) model and experimental data. The results indicate the new two-stage flow stress model can more accurately represent the hot deformation behavior of X12 ferrite heat-resistant steel, and the average error is only 0.0995.
026506
Da He, Shufan Wang, Rutie Liu, Zhubo Wang, Xiang Xiong and Jianpeng Zou
Porous wicks were prepared via powder metallurgy using NH4HCO3 powders as pore-forming agent. The pore-forming agent particle size was varied to control the pore structure and equivalent pore size distribution feature of porous wick. The effect of pore-forming agent particle size on the porosity, pore structures, equivalent pore size distribution and capillary pumping performance were investigated. Results show that with the particle size of pore-forming agent decrease, the green density and the volume shrinkage of the porous wicks gradually increase and the porosity reduces slightly. There are two types of pores inside the porous wick, large-sized prefabricated pores and small-sized gap pores. With the particle size of pore-forming agent decrease, the size of the prefabricated pores becomes smaller and the distribution tends to be uniform. Gap pores and prefabricated pores inside the wick can make up different types of pore channels. The equivalent pore size of wick is closely related to the structure of pore channels. Furthermore, the equivalent pore size distribution of wick shows an obvious double-peak feature when the pore-forming agent particle size is large. With the particle size of pore-forming agent decrease, the two peaks of equivalent pore size distribution approach gradually to each other, resulting in a single-peak feature. Porous wick with single-peak feature equivalent pore size distribution possesses the better capillary pumping performances.
026507
Lin He, Yimin Gao, Yefei Li, Zhiwei Liu, Wenyan Zhai and Weiyao Zhang
Effect of milling time on the microstructure and mechanical properties of Ti(C,N)-304 stainless steel cermet and the fracture mechanism were studied in this work. The microstructure was investigated by means of x-ray diffraction (XRD), scanning electron microscope (SEM) combined with energy dispersive spectrometer (EDS), and field emission transmission electron microscope (FETEM). FETEM and EDS were also used to analyze the Ti(C,N)/304ss interface. Mechanical properties such as transverse rupture strength (TRS) and hardness were also measured. Results show that prolonged milling time decreases the Ti(C,N) grain size and improves the homogeneity of microstructure. As a consequence, the frequency of intergranular fracture increased and it can improve the mechanical properties. Fe and Ti elements could interdiffuse and the hard phase was closely bonded with binder phase. The Ti(C,N)/Ti(C,N) interface was weaker than Ti(C,N)/304ss interface. Results also show that the transverse rupture strength and the hardness increase with increasing milling time and the maximum values were obtained at 18 h with 1437 MPa and 83.7 HRA, respectively.
026508
O Gerlach, A Lechler and A Verl
Controlled heating of metal billets into the semi-solid state for thixoforming is a challenging task, mainly due to the difficulties in measuring the liquid fraction of the billet during heating. Past research primarily focused on methods measuring the liquid fraction during heating of low-melting aluminium alloys. One of these methods is time constant measurement, a contactless measurement method that uses the heating coil as a sensor. The current through the coil is used to determine the electrical time constant of the heating circuit, which itself is influenced by the specific resistance of the billet inside the coil. While previous works focused on the suitability of this method for industrial applications using aluminum alloys, this paper extends this research to the high-melting titanium alloy Ti6Al4V. This alloys shows high strength, low density and excellent corrosion resistance. It is therefore used to produce light-weight and durable components for medical and aerospace applications. Ti6Al4V is an expensive and difficult to machine alloy. Thus, it is an interesting alloy for thixoforging. However, heating of the billet into a homogeneous state of defined liquid fraction is difficult due to the poor thermal conductivity of Ti6Al4V. This paper analyses the potential of using time constant measurement for controlled heating of Ti6Al4V into the semi-solid state.
026509
H Bahmanabadi, S Rezanezhad, M Azadi and M Azadi
This article has presented suitable creep lifetime prediction models for Inconel-713C nickel-based superalloy. For such objective, the characterization of the creep damage and lifetime has been performed by considering stress-based model, strain/strain rate models and continuum damage mechanics models. For calibrating material models, creep tests at 850 °C have been performed on the Inconel-713C nickel-based superalloy under different stress levels. Obtained results indicated that reliable/valid models, according to a proper relative error and a low scatter-band, were the Monkman-Grant strain rate-based model and the continuum damage mechanics model. The scanning electron microcopy (SEM) analysis showed that the matrix pattern of crept specimens changed, when the applied stress changed under creep loading. In addition, the one-dimension form could be considered for the shape of carbides.
026510
Chuanqi Shi, Xinhong Xiong, Chao Zhu, Qiaoxin Zhang, Jialin Chen and Yongjie Lei
The tantalum tungsten alloys, Ta-2.5 W and Ta-10 W, were treated with isothermal ion nitriding and two-stage ion nitriding experiments to obtain a nitride layer. After the treatment, the hardness of both alloys has been remarkably improved, which can be attributed to the formation of nitride phase θ-TaN in the surface layer according to the XRD pattern. Comparing with isothermal ion nitriding, the two-stage ion nitriding experiment achieved greater microhardness and thickness of the nitride layer. In addition, T-2.5 W alloy showed a greater layer thickness and microhardness than Ta-10 W alloy with the same treatment, which indicates that the nitriding process decreases with the increase of tungsten content.
026511
Moshabab A Asiry, Ibrahim AlShahrani, Salem Almoammar, Bangalore H Durgesh, Abdulaziz A Al Kheraif and Mohamed I Hashem
Aim. To investigate the effect of epoxy, polytetrafluoroethylene (PTFE) and rhodium surface coatings on surface roughness, nano-mechanical properties and biofilm adhesion of nickel titanium (Ni-Ti) archwires Methods. Three different coated (Epoxy, polytetrafluoroethylene (PTFE) and rhodium) and one uncoated Ni-Ti archwires were evaluated in the present study. Surface roughness (Ra) was assessed using a non-contact surface profilometer. The mechanical properties (nano-hardness and elastic modulus) were measured using a nanoindenter. Bacterial adhesion assays were performed using Streptococcus mutans (MS) and streptococcus sobrinus (SS) in an in-vitro set up. The data obtained were analyzed using analyses of variance, Tukey’s post hoc test and Pearson’s correlation coefficient test. Result. The highest Ra values (1.29 ± 0.49) were obtained for epoxy coated wires and lowest Ra values (0.29 ± 0.16) were obtained for the uncoated wires. No significant differences in the Ra values were observed between the rhodium coated and uncoated archwires (P > 0.05). The highest nano-hardness (3.72 ± 0.24) and elastic modulus values (61.15 ± 2.59) were obtained for uncoated archwires and the lowest nano-hardness (0.18 ± 0.10) and elastic modulus values (4.84 ± 0.65) were observed for epoxy coated archwires. No significant differences in nano-hardness and elastic modulus values were observed between the coated archwires (P > 0.05). The adhesion of Streptococcus mutans (MS) to the wires was significantly greater than that of streptococcus sobrinus (SS). The epoxy coated wires demonstrated an increased adhesion of MS and SS and the uncoated wires demonstrated decreased biofilm adhesion. The Spearman correlation test showed that MS and SS adhesion was positively correlated with the surface roughness of the wires. Conclusion. The different surface coatings significantly influence the roughness, nano-mechanical properties and biofilm adhesion parameters of the archwires. The evaluated parameters were most influenced by epoxy coating followed by PTFE and rhodium coating. A positive correlation was detected between surface roughness and biofilm adhesion.
026512
Rongcheng Wang, Yongxin Zhao, Zhuxin Li, Hongmei Chen, Xiaoma Tao and Yifang Ouyang
We investigate the lattice constant, formation enthalpy, elastic constants, bulk modulus, shear modulus, Young’s modulus, specific heat, thermal expansion coefficient and microhardness as a function of Al content for B2-FeAl and D03-Fe3Al using static and dynamics simulations with a long-range analytical embedded atom method (la-EAM). The lattice constants of both B2-FeAl and D03-Fe3Al crystals increase with Al content, opposite to the elastic constants, bulk modulus and shear modulus. Stoichiometric B2-FeAl has the lowest formation enthalpy and Young’s modulus. The calculation results of Gibbs free energies show that the phase transformation temperature from D03 to B2 decreases with Al content, which is in good agreement with experiments. The microhardness resulting from vacancies for B2-FeAl increases monotonically with Al content, indicating that the resultant microhardness is controlled by the vacancies, which agrees well with experiments.
026513
Hai Mei, Shuang Xu, Lisheng Liu, Wuchang She, Jun Li and Zhengyi Fu
026514
Kai Ni, Qian Ma, Hao Wan, Bin Yang, Junjie Ge, Lingyu Zhang and Naichao Si
The evolution of microstructure for 7075 aluminum alloys with 50 Kev helium ions irradiation were studied by using optical microscopy (OM), scanning electron microscopy (SEM), x-ray diffraction (XRD) and transmission electron microscopy (TEM). The fluences of 1 × 1015, 1 × 1016 and 1 × 1017 ions cm−2 were selected, and irradiation experiments were conducted at room temperatures. The transmission process of He+ ions was simulated by using SRIM software, including distribution of ion ranges, energy losses and atomic displacements. Experimental results show that irradiated pits and micro-cracks were observed on irradiation sample surface, and the size of constituent particles (not including Mg2Si) decreased with the increasing dose. The x-ray diffraction results of the pair of peaks is better resolved in irradiated samples might indicate that the stressed structure consequence due to crystal defects (vacancies and interstitials) after He+ implantation. TEM observation indicated that the density of MgZn2 phase was significantly reduced after helium ion irradiation which is harmful to strength. Besides, the development of compressive stress produced a large amount of dislocation defects in the 1015 ions cm−2 sample. Moreover, higher fluence irradiation produced more dislocations in sample. At fluence of 1016 ions cm−2, dislocation wall formed by dislocation slip and aggregation in the interior of grains, leading to the refinement of these grains. As fluence increased to 1017 ions cm−2, dislocation loops were observed in pinned dislocation. Moreover, dislocation as effective defect sink, irradiation-induced vacancy defects aggregated to these sinks, and resulted in the formation of helium bubbles in dislocation.
026515
Chen Jinshui, Yang Bin, Wang Junfeng, Xiao Xiangpeng, Chen Huiming and Wang Hang
The crystallography and morphology of precipitate particles of Cu-Cr-Zr alloys with varying Zr contents were studied by transmission electron microscopy (TEM) after solution treatments at 950 °C for 1 h and aging treatments at 500 °C for different times ranged from 0.5 h to 24 h. The microhardness and electrical conductivity of Cu-Cr-Zr alloys after various aging process were tested. The results show that the microhardness and electrical conductivity rapidly increased at first, then the microhardness decreased slowly after reaching the peak, while the conductivity continues to increase. Nano-scaled precipitates exhibit two kinds of morphology (coffee bean and ellipse shaped). With increasing Zr content, the Zr-containing precipitation sequence of Cu-Cr-Zr alloys at peak-ageing is Heusler CrCu2Zr → Cu5Zr → Cu4Zr. The Heusler CrCu2Zr phase decomposed into fine and homogeneous Cr and Cu4Zr, resulting in improved alloy properties.
026516
Kai-Peng Lin, Te-Hua Fang and Ying-Jhin Lin
In this study, we investigate the mechanical properties of single-crystal copper (Cu) nanopillars. Critical deformation variations of Cu-nanopillared structures are estimated using in situ transmission electron microscopy compression tests and molecular dynamics simulations. The Young’s moduli of Cu nanopillars with diameters of 2–6 nm were 90.20–124.47 GPa. The contact stiffnesses of the Cu nanopillars with diameters of 400 and 500 nm were 1.33 and 3.86 N m−1, respectively; the Poisson’s ratios for these nanopillars were 0.32 and 0.33. The yield strength of the nanopillars varied from 0.25 GPa at 500 nm to 0.42 GPa at 400 nm; the yield strength of single-crystal Cu nanopillars decreased with increasing diameter. The values of the indented hardness of the Cu block were 0.27 and 1.06 GPa, respectively. Through experimental work and molecular dynamics simulations, we demonstrate that Cu nanopillars exhibit internal stress transmission during compression. When compression reaches the maximum strain, it can be observed that Cu slips. Our results are useful for understanding the mechanical properties, contact, and local deformation of Cu nanopillars.
026517
Guanghui Zhao, Yugui Li, Juan Li, Qingxue Huang and Lifeng Ma
Rolling reduction and base layers thickness have important implications for rolling compounding. A two-layered 304 stainless steel/Q345R low alloyed steel was roll bonded. The roll bonding was performed at the three thickness reductions of 25%, 40% and 55% with base layers of various thicknesses (Q345R). The microstructures of the composite were investigated by the ultra-deep microscope (OM) and scanning electron microscope (SEM) and Transmission electron microscope (TEM). Simultaneously, the mechanical properties of the composite were experimentally measured and the tensile fracture surfaces were observed by SEM. The interfaces were successfully bonded without any cracking or voids, which indicated a good fabrication of the 304/Q345R composite. The rolling reduction rate and thinning increase of the substrate contributed to the bonding effects appearance of the roll bonded sheet. The Cr and Ni enriched diffusion layer was formed by the interface elements diffusion. The Cr and Ni diffusion led to the formation of ∼10 μm wide Cr and Ni layers on the carbon steel side.
026518
Abhinav Gautam, K Priya Ajit and Prabir Kumar Sarkar
A nonlinear ductile damage growth criterion is proposed based on continuum damage mechanics (CDM) approach. The model is derived in the framework of thermodynamically consistent CDM assuming damage to be isotropic. In this study, the damage dissipation potential is also derived to be a function of varying strain hardening exponent in addition to damage strain energy release rate density. Uniaxial tensile tests and load-unload-cyclic tensile tests for AISI 1020 steel, AISI 1030 steel and Al 2024 aluminum alloy are considered for the determination of their respective damage variable D and other parameters required for the model(s). The experimental results are very closely predicted, with a deviation of 0%–3%, by the proposed model for each of the materials. The model is also tested with predictabilities of damage growth by other models in the literature. Present model detects the state of damage quantitatively at any level of plastic strain and uses simpler material tests to find the parameters of the model. So, it should be useful in metal forming industries to assess the damage growth for the desired deformation level a priori. The superiority of the new model is clarified by the deviations in the predictability of test results by other models.
026519
Dongbo Wei, Pingze Zhang, Yingchao Liu, Xiaohu Chen, Feng Ding and Fengkun Li
The Zr coating and Zr-Er coating are grown on TC11 substrate by double-glow plasma surface metallurgy technique, followed by the wear tests at ambient temperature and 500 °C. The data of nanohardness and elastic modulus of the samples are collected by the nano-indentation test. The adhesion strength of coatings is investigated by means of the scratch test. The study of wear resistance is performed using a ball-on-disc wear test system by running against the Si3N4 ball and measured by scanning electron microscope (SEM) and X-ray diffraction (XRD). Experimental results indicate that the nanohardness of the Zr coating and Zr-Er coating are 5.94 GPa and 7.98 GPa, respectively, which are 1.79 times and 2.41 times greater than that of TC11 substrate. Zr coating and Zr-Er coating realize the metallurgical bonding with TC11 substrate with continuous and compact structure. Compared with the Zr coating and TC11, the Zr-Er coating presents the lowest specific wear rates, which are 1.689 × 10−6 mm3 Nm−1 and 1.851 × 10−6 mm3 Nm−1 at ambient temperature and 500 °C respectively, indicating the excellent and improved wear resistance of TC11.
026520
Mohsen Hajizamani, Mostafa Alizadeh, Ali Alizadeh and Seyed Ahmad Jenabali-Jahromi
A thermomechanical processing (TMP) method was employed to modify the characteristics of Al-Zn-Mg/3 wt% Al2O3 composite including the microstructure and the mechanical properties. The composite powders were subsequently cold pressed at 115 MPa and solid state sintered at 550 °C for 90 min under argon atmosphere. The TMP was then performed on the samples consisting of an additional cold pressing at 250 MPa followed by a partial remelting stage in the semi-solid state for 30 min under argon atmosphere. Four different temperatures corresponding to four percentages of melt content were chosen to apply in the TMP to study the role of the melt content on the microstructure and mechanical properties of the modified samples. The observations obtained from the characterizations and mechanical tests showed that drastic alteration in the solid sintered microstructure occurred by reducing the porosity level and creating a solidified network as grain boundaries. However, with increasing the melt percentage up to 20%, decreasing the average grain diameter along with increasing the microhardness and compressive strength was observed.
026521
N Rajesh Jesudoss Hynes and P Shenbaga Velu
In the last two decades, major car manufacturing companies are exploring the possibilities of joining magnesium with aluminium, via friction welding technique for many crucial automotive applications. Our primary objective, is to carry out an experimental investigation in order to study the behaviour of dissimilar joints. The microscopic structure at the welded joint interface was analysed using an optical microscopy and scanning electron microscope. It was found that, by increasing the value of friction time, the value of the tensile strength increases and the result of tensile strength is found to be 120 MPa at a friction time of 10 s. Micro hardness was found to be higher at the interface of the weldment due to the development of a brittle intermetallic compound. Micro structural studies using SEM reveals, distinct zones such as an unaffected parent metal zone, the heat affected zone, a thermo-mechanically affected zone and a fully deformed plasticised zone.
026522
Junhai Wang, Bing Lu, Lixiu Zhang, Ting Li, Tingting Yan and Mengxu Li
The Co(ReO4)2 powder was fabricated via the aqueous solution method, and mixed with MoS2 powder using ball milling technique. A certain concentration of Co(ReO4)2/MoS2 composite additive was dispersed into the poly alpha olefin base oil with the assistance of surface active agents. The load-carrying property and lubricating behavior of base oil containing a certain content of Co(ReO4)2/MoS2 composite additive at various temperatures were evaluated by four-ball test and ball-on-disc sliding friction test. The physical properties and friction-reducing mechanism of synthesized composite were ascertained by a series of characterization techniques including X-ray diffraction, scanning electron microscopy-energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and differential thermal analysis/thermogravimetry. The four-ball test results suggested the Co(ReO4)2/MoS2 composite additive could effectively promote the load-carrying capacity of base oil, and decrease the friction coefficient as well as wear scar diameter. Ball-on-disc sliding friction test results showed that the base oil with Co(ReO4)2/MoS2 composite additive possessed lower friction coefficients than that of base oil in the whole temperature range, particularly at high temperatures. The protective layer consisted of composite additive and native oxides from superalloy substrate formed on the worn surface to prevent the direct contact between friction pair. The Co(ReO4)2/MoS2 composite played a dominant role in friction-reducing function in the protective layer at elevated temperatures, and the reason for this was that MoS2 possessed layered structure and superior adsorption capacity, and Co(ReO4)2 had experienced thermal softening with elevated temperatures and maintained shear-susceptible hexagonal structure.
026523
L Gyansah, N H Tariq, J R Tang, X Qiu, B Feng, J Huang, H Du, J Q Wang and T Y Xiong
In this paper, cold spray was used as an additive manufacturing method to fabricate 5 mm thick SiC/Al metal matrix composites with various SiC contents. The effects of SiC contents and heat treatment on the microstructure, thermophysical and flexural properties were investigated. Additionally, the composites were characterized for retention of SiC particulates, splat size, surface roughness and the progressive understanding of strengthening, toughening and cracking mechanisms. Mechanical properties were investigated via three-point bending test, thermophysical analysis, and hardness test. In the as-sprayed state, flexural strength increased from 95.3 MPa to 133.5 MPa, an appreciation of 40% as the SiC contents increased, and the main toughening and strengthening mechanisms were zigzag crack propagation and high retention of SiC particulates respectively. In the heat treatment conditions, flexural strength appreciated significantly compared to the as-sprayed condition and this was as a result of coarsening of pure Al splat. Crack branching, crack deflection and interface delamination were considered as the main toughening mechanisms at the heat treatment conditions. Experimental results were consistent with the measured CTE, hardness, porosity and flexural modulus.
026524
Zhi Li, Zhen Zhao, Zhonghao Zhou and Qi Wang
To investigate the interface between the main phases of Cu-Sc alloys, the structures, stability and electronic properties of bimetallic Cun−1Sc and Cun−2Sc2 (n = 2–7) clusters are systematically calculated by the GGA-PW91 functional. The results reveal that the structures of Cun−1Sc and Cun−2Sc2 (n = 2–7) clusters inherited those of pure Cun (n = 2–7) clusters and they maintained higher symmetry. Cu5Sc cluster possesses more stable than its neighbors while Cu2Sc2 cluster is less stable than its neighbors by binding energy. Cu5Sc cluster possesses the highest kinetic stability of Cun−1Sc clusters and CuSc2, Cu3Sc2 and Cu5Sc2 clusters possess higher kinetic stability than their neighbors by HOMO-LUMO gap. NBO analysis reveals that Cu-Sc atoms have less pd orbital hybridization in the Sc doping Cun (n = 2–7) clusters.
026525
Dekun Zhang, Ruoqi Yu, Kai Chen, Xuehui Yang, Yuan Liu and Yan Yin
Plasma cladding technology is used to prepare a plasma cladding gradient wear-resistant layer, and the corrosion and corrosion-friction properties of the plasma cladding wear-resistant layer are analyzed. The results indicate that under pure immersion corrosion, the plasma gradient cladding wear-resisting layer has better corrosion resistance compared with that of single cladding specimen. No obvious corrosion traces occur on the corrosion surface. Under corrosion-friction conditions, the variety law of friction coefficient can be divided into four stages: rapid decline zone, slight increase zone, fluctuation zone and steady zone. The fluctuation ranges of friction coefficient and wear loss greatly reduce compared with those of dry friction. Furthermore, the wear scar has no obvious corrosion traces. The wear mechanism of the substrate is corrosion wear, adhesive wear, abrasive wear and fatigue wear, while the plasma cladding gradient wear-resistant layer is given priority to with adhesive wear and abrasive wear.
026526
Arkadeb Mukhopadhyay, Tapan Kumar Barman and Prasanta Sahoo
Sodium borohydride reduced electroless nickel alloy coatings have high wear resistance and low coefficient of friction. The present work investigates the deposition and tribological behavior of a ternary variant of the borohydride reduced coating i.e. Ni-B-W. Electroless Ni-B-W coatings were deposited on AISI 1040 steel substrates. In order to improve the mechanical properties of the deposits, they were heat treated at 350 °C for 1 h. The coatings in their as-deposited and heat treated conditions were characterized by scanning electron microscope, energy dispersive x-ray analysis and x-ray diffraction techniques. Ni-B-W coatings are amorphous in their as-deposited state while they become crystalline on heat treatment. In fact a high microhardness of Ni-B-W coatings is also observed in as-deposited condition. The microhardness further improves on heat treatment. Tribological behavior of the heat treated coatings with varying load (10–50 N), sliding speed (0.25–0.42 m s−1) and operating temperature (25 °C–500 °C) were evaluated on a pin-on-disc type test setup while the wear mechanisms were also studied. Tribological behavior of Ni-B-W coatings is enhanced at 500 °C operating temperature in comparison with 100 or 300 °C due to formation of protective oxide scales and microstructural changes due to in-situ heat treatment effect.
026527
Yongmei Zhang, Yuhong Zhao, Hua Hou, Zhiqin Wen and Meiling Duan
The mechanical and thermodynamic properties of fcc and bcc Ti have been discussed based on the first-principles calculation combined with the quasi-harmonic Debye model. We find that the bulk modulus B, shear modulus G, Young’s modulus E of fcc Ti are larger, while Poisson’s ratio σ is smaller than that of bcc Ti under the same pressure, which indicates the better mechanical performance of fcc Ti compared with bcc Ti. The values of B/G and σ indicate that mechanically stable fcc structure is much less ductile than the bcc structure, while mechanically metastable fcc structure has better ductility than stable bcc structure under high pressure. The normalized volume, isothermal bulk modulus, heat capacity, volume thermal expansion coefficient and Debye temperature under pressure and temperature for fcc and bcc Ti are predicted.
026528
Vipin Tandon, Awanikumar P Patil, Ramesh C Rathod and Sourabh Shukla
The influence of cold work (CW) on electrochemical behavior of 316L ASS in PEMFC (0.5M H2SO4 + 2 ppm HF at 70 °C) environment was investigated by microstructural observations, x-ray diffraction (XRD), polarization, electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) techniques. The XRD is used to analyze the increase in dislocation density and formation of α′-martensite with increasing CW degree. The EIS is used to find out the effect of substrate dislocation density on the film resistance. The EIS result show that with increasing CW, the diameter of depressed semi-circular arc and consequently film resistance decreased. This indicates the formation of highly disordered and porous film on CW. From PDP results, it is found that icrit, ip and icorr increased on increasing CW degree. Moreover, the direct relationship was drawn from the dislocation density of the substrate to the defect density of the passive film from M-S technique.
026529
Yu Sun, Shunjie Gu, Qian Wang, Huibin Wang, Qingfeng Wang and Fucheng Zhang
The 28CrMo48VTiB martensitic steel for sulfide stress cracking (SSC) resistance oil country tubular goods (OCTG) of C110 grade was thermally processed through quenching at 890 °C and tempering at 600 °C–720 °C for 30–90 min. The microstructures of all samples were characterized using field emission scanning electron microscopy (FESEM), electron backscattering diffraction (EBSD), transmission electron microscopy (TEM) and x-ray diffractometry (XRD). Also, the tensile properties were measured. The results indicated that the yield strength (YS) decreased as both the tempering temperature and duration increased, due to the coarsening of martensitic packet/block/lath structures, the reduction of dislocation density, as well as the increase of both the volume fraction and average diameter of the precipitates. The martensitic lath width was the key microstructural parameter controlling the YS of this heavily-tempered martensitic steel, whereas the corresponding relationship was in accordance with the Langford-Cohen model. Furthermore, the martensitic structure boundary and the solid solution strengthening were the two most significant factors dominating the YS, in comparison with the dislocation and precipitation strengthening.