Batteries and Energy Storage
A697
G. B. Less, J. H. Seo, S. Han, A. M. Sastry, J. Zausch, A. Latz, S. Schmidt, C. Wieser, D. Kehrwald and S. Fell
A fully parameterized microscale model for lithium ion cells is presented in which the solid and pores (filled by electrolyte) are spatially resolved, and the mass and charge transport equations describing diffusion and migration in each phase are solved separately. Such a model allows: (1) the correlation of structure-scale, non-homogeneous material properties with macroscopic battery performance, and (2) the correlation of geometrical electrode morphology with macroscopic battery performance (electrode design). The micro-model approach discussed here allows for a simpler parameterization as fewer constitutive relations are needed in contrast to the macro-homogenous physical-based approaches. Input parameters were measured experimentally on lithium manganese oxide electrodes and LiPF6 in 3:7 EC:DMC. Verification and validation for the model is also reported.
A705
A. J. Smith, Hannah M. Dahn, J. C. Burns and J. R. Dahn
The capacity loss and coulombic efficiency of commercial LiCoO2/graphite Li-ion cells have been examined using high precision coulometry and long-term cycling tests. The experiments show that time, not cycle count, was the dominant contributor to the degradation of LiCoO2/graphite Li-ion cells cycled at low rates and elevated temperatures. The differential voltage versus capacity, dV/dQ vs Q, of the cells was measured for all cycles during the extended cycling and fit using predicted dV/dQ vs Q plots calculated from Li/graphite and Li/LiCoO2 cells made from the same electrodes that were used in the commercial cells. From this analysis it was possible to determine fraction of positive and negative electrode masses that remained active as a function of cycle number and also the portion of capacity loss due to the relative slippage of the positive and negative electrode potential-capacity curves. A rapid impedance rise was observed near the end of the cycling testing. These results provide a model procedure for understanding of the failure of lithium-ion cells subjected to sustained high temperature cycling.
A711
M. A. Al-Maghrabi, J. S. Thorne, R. J. Sanderson, J. N. Byers, J. R. Dahn and R. A. Dunlap
In the present work three pseudobinary libraries of the Sn-Si-C system were produced using combinatorial methods. X-ray diffraction was used to study the structure of these libraries and Mossbauer spectroscopy was employed to probe the atomic environment. Cyclic voltammetry measurements were performed using a multichannel pseudopotentiostat to study the behavior of these materials as negative electrodes for Li-ion batteries. These three libraries were compared in terms of the phases formed, amorphous vs. crystalline structure, the reversible capacity as a function of composition and the capacity retention. The addition of carbon to Sn-Si inhibits the aggregation of Sn into regions of relatively pure tin. This minimization of free tin has the effect of improving cycleability by reducing the adverse effects of volume expansion, by eliminating two-phase coexistence regions during delithiation and lithiation.
A720
Hiroki Kitamura, Liwei Zhao, Bui Thi Hang, Shigeto Okada and Jun-ichi Yamaki
A composite Fe2O3/C powder was applied as a negative material in iron/air batteries. The effect of charge current density on the electrochemical behavior of an electrode in KOH electrolyte without or with K2S additives was investigated. In KOH electrolyte, the discharge capacity increased in proportion to the logarithm of charge current density in the range of 10–40 mA cm−2. According to an analysis of Tafel plots of the electrodes, the hydrogen evolution was found to reach its diffusion limit earlier than the reduction reaction of Fe(OH)2 to Fe as charge current density increased. This was deduced to be the reason for the increase of discharge capacity with current density. But as the density increased further, the discharge capacity decreased because both above reactions reached their diffusion limits. When K2S additives were used, a similar phenomenon was observed, with a higher discharge capacity than that without additives. It indicated that the practical capacities of iron/air batteries could be increased through the depression of hydrogen evolution by optimizing the charge current density for the batteries. At a charge current density of 50 mA cm−2, the Fe2O3/C electrode showed the highest discharge capacity of 810 mAh g−1-Fe2O3 in K2S-added electrolyte.
A725
Akira Kojima, Toshikatsu Kojima, Tabuchi Mitsuharu and Tetsuo Sakai
A new lithium iron silicate cathode material with only trivalent iron was obtained by aging Li2FeSiO4/carbon composite for one year at room temperature. Crystal structure of the new material was supposed to belong to monoclinic system in space group P21/n with cation disordering of Li+ and Fe3+ based on the Rietveld refinement and transmission electron microscopy (TEM) observation. The new material evaluated using lithium foil as an anode showed initial charge and discharge capacities of 243 and 182 mAh g−1 and stable charge-discharge one of about 150 mAh g−1 at the second cycle. Only trivalent iron was observed for the new material after initial charge by 57Fe Mössbauer spectroscopy, suggesting the contribution of other redox species except for Fe ion. The new material with trivalent iron is stable in air and can deliver stable charge-discharge capacity, promising to be potential cathode material for lithium-ion batteries.
A730
Hadi Tavassol, Joseph W. Buthker, Glen A. Ferguson, Larry A. Curtiss and Andrew A. Gewirth
We report the results of electrochemical quartz crystal microbalance (EQCM), and matrix assisted laser desorption ionization (MALDI) time of flight (TOF) mass spectrometry (MS) measurements along with detailed calculations examining the formation of the solid electrolyte interphase (SEI) on battery anode electrodes. EQCM analysis of Au and Sn surfaces in propylene carbonate (PC) and a 1:1 mixture of ethylene carbonate and dimethyl carbonate (EC:DMC) showed major irreversible mass uptake by the electrode surface especially during the first five cycles between +2 and 0.1 V vs. Li/Li+. MALDI-MS on emersed electrodes showed that long chain (m/z = 3000 on PC) oligomerized species were present on Au surfaces in PC and EC:DMC solvents, where oligomerized species formed in PC solutions showed higher mass ratios. The repeating units of the oligomer, visible as oscillations in the MALDI-MS, vary with the type of the solvent and electrode material. Sn surfaces initially showed formation of long chain polymers, but this material was not in evidence on electrode emersed after five cycles, which likely arises as a consequence of the catalytic involvement of Sn in decomposition of initially formed species. Density functional theory (DFT) calculations of cyclic solvent molecules suggested a radical initiated polymerization mechanism and predict oligomer subunits consistent with the experimental results.
A739
Marshall C. Smart, Brett L. Lucht, Swapnil Dalavi, Frederick C. Krause and Bugga V. Ratnakumar
The effect of additives upon the ability of meso-carbon microbead (MCMB) carbon/ LiNixCo1−xO2 lithium-ion cells containing methyl butyrate-based electrolytes to provide operation over a wide temperature range (−60 to +60°C) was investigated. A number of electrolyte additives were studied, including mono-fluoroethylene carbonate (FEC), lithium oxalate, vinylene carbonate (VC), and lithium bis(oxalato borate) (LiBOB). The intent of incorporating these additives into methyl butyrate-based electrolytes is to widen the operating temperature range of these systems, especially at warm temperatures. A number of formulations were investigated in experimental three-electrode MCMB/ LixNiyCo1−yO2 lithium-ion cells, based on an electrolyte that has previously been demonstrated to provide good low temperature performance (to −60°C), namely 1.00M LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + methyl butyrate (MB) (20:20:60 v/v%). In addition to studying the charge and discharge behavior of the cells, a number of electrochemical techniques were also employed, including Electrochemical Impedance Spectroscopy (EIS), Tafel polarization and linear polarization to understand the interfacial effects on the intercalation kinetics.
A752
The following article is Free article
Gouri Radhakrishnan, Joanna D. Cardema, Paul M. Adams, Hyun I. Kim and Brendan Foran
Single and multilayer graphene films offer the potential for significant weight reduction in lithium-ion batteries for next-generation power systems, including microbatteries. When scaling down Li-ion battery size and weight, it is important to understand the impact of reducing the number of graphene layers on electrochemical performance. We compared the electrochemical performance of anodes fabricated from pristine single layer graphene (SLG), few layers of multilayer graphene (MLG), and several thousand layers of highly oriented pyrolytic graphite (HOPG). Coin-cell anodes were fabricated without a binder from graphene films grown directly on copper and nickel foils. Cycling at 5 μA/cm2 indicated reversible capacities of ∼0.047 and 0.040 mAh/cm2 for SLG-Cu and MLG-Ni. Subtracting substrate contribution and normalizing to the mass of the graphene layer(s), the specific capacities for SLG and MLG are high (13263 mAh/g and 1185 mAh/g). Distinct peaks were observed in cyclic voltammograms of MLG indicating lithium intercalation into the graphene layers, but not in SLG, suggesting a different mechanism for lithium storage. XPS results of charged SLG-Cu suggest that the reversible charge is present both on top of the SLG and between SLG and Cu. The performance of HOPG was poor (23 mAh/g) and appears to be Li-diffusion limited.
A762
M. V. Reddy, X. W. Valerie Teoh, T. B. Nguyen, Y. Y. Michelle Lim and B. V. R. Chowdari
The compounds, TiO2−1 & −2 were synthesized by 0.5 M NaNO3: 0.5 M KNO3 (I) and 0.88 M LiNO3:0.12 MLiCl (II) salts at 510°C and 280°C, resp.., XRD studies show single anatase phase with characteristic tetragonal lattice parameter values of a ∼3.78 Å and c ∼ 9.51 Å. The TEM images show aggregates of 10–30 nm sized nanosquares (TiO2−1) and spherical particles (TiO2−2). Surface area of the TiO2 powders were 74 and 200 m2 g−1, resp. for 1 and 2. Upon heat-treatment (TiO2−2) from 500°C to 850°C, the surface area decreases from 80 to 0.7 m2 g−1. Cyclic voltammetry studies show cathodic and anodic peaks at ∼1.7 and ∼ 2.0 V, resp. for both bare and heat treated TiO2 up to 750°C. Galvanostatic cycling studies show that the first discharge-charge capacity values are 244 and 198 (±3) mAh g−1 resp. for TiO2−1 at a current of 33 mA g−1 in the voltage window, 1.0–2.8 V vs. Li/Li+. TiO2−2 nanoparticles show a less capacity fade during cycling and delivered first discharge-charge capacity values of 340 and 253 (±3) mAh g−1, resp. at a current rate of 33 mA g−1. The effects of heat-treatment and Li-cycling at a cutoff voltage (0.005 V) were studied and discussed reaction mechanism.
A770
P. Andrei, J. P. Zheng, M. Hendrickson and E. J. Plichta
Li-air batteries with organic electrolyte at the anode and aqueous electrolyte at the cathode (dual electrolyte systems) are modeled using the mass transport and drift-diffusion equations of the electrolyte during the discharge of the cells. Two regimes of operation are analyzed: (1) when the concentration of the electrolyte is smaller than the concentration of saturation of Li+OH− in water, and (2) when the electrolyte concentration reaches saturation and the reaction product is deposited at the cathode. Numerical simulations are performed to evaluate the dependence of the specific capacity, energy and power densities on the geometrical and material parameters during the two regimes of operation. It is shown that the energy density and specific capacity can be improved by increasing the solubility and the diffusion coefficient of oxygen in the cathode, but they are not much affected by adding a uniformly distributed catalyst in the cathode. The power density can be increased by 10% by increasing the solubility factor, the oxygen diffusion coefficient, or the reaction rate. The limiting factors for the low power density of these batteries are the low values of the oxygen diffusion coefficient in the cathode and the relatively high separator/anode and separator/cathode interface resistances.
A781
Jason R. Croy, Donghan Kim, Mahalingam Balasubramanian, Kevin Gallagher, Sun-Ho Kang and Michael M. Thackeray
A new approach to synthesizing high capacity lithium-metal-oxide cathodes for lithium-ion batteries from a Li2MnO3 precursor is described. The technique, which is simple and versatile, can be used to prepare a variety of integrated ‘composite’ electrode structures, such as ‘layered-layered’ xLi2MnO3•(1–x)LiMO2, ‘layered–spinel’ xLi2MnO3•(1–x)LiM2O4, ‘layered-rocksalt’ xLi2MnO3• (1–x)MO and more complex arrangements, in which M is typically Mn, Ni, and/or Co. Early indications are that electrodes prepared by this method are effective in 1) countering the voltage decay that occurs on cycling ‘layered-layered’ xLi2MnO3•(1–x)LiMO2 electrodes without compromising capacity, and 2) reducing the extent of electrochemical activation required above 4.5 V on the initial charge. In particular, a 0.5Li2MnO3•0.5LiMn0.5Ni0.5O2 electrode, after activation at 4.6 V, delivers a steady capacity of 245 mAh/g between 4.4 and 2.5 V at 15 mA/g (∼C/15 rate) with little change to the voltage profile; a first cycle capacity loss of 12%, which is significantly less than usually observed for ‘layered-layered’ electrodes, has been achieved with a manganese-rich 0.1Li2MnO3•0.9LiMn0.50Ni0.37Co0.13O2 electrode. These results have implications for enhancing the performance of the next generation of high-energy lithium-ion batteries. The flexibility of the method and the variation in electrochemical properties of various composite electrode structures and compositions are demonstrated.
A791
Søren Højgaard Jensen, Kurt Engelbrecht and Carlos Bernuy-Lopez
Detailed characterization of battery modules is necessary to construct reliable models that incorporate performance related aspects of the modules such as thermodynamics, electrochemical reaction kinetics and degradation mechanisms. Charge-discharge curves, temperature and battery impedance measurements can provide information about these aspects. Charge-discharge curves can be used to measure the battery open circuit voltage and the internal resistance. Temperature measurements provide information about the thermodynamic reactions and impedance spectra yield detailed information about the reaction kinetics. In this paper we present the measurement methods used to examine the internal resistance, the capacity and the impedance of a 75 Ah NMC battery module. In order to measure the impedance of the battery module and of the individual cells in the module, we combine the single sine technique and the Laplace transformed excitation signal technique which each have pros and cons. By combining the two impedance measurement techniques we are able to reduce the measurement time by a factor of 20 relative to ordinary single-sine measurements. Further we use the impedance measurements to calculate the overvoltage as a function of state of charge and the difference between charging overvoltage and discharging overvoltage and compare it with measurements.
A798
Ali Awarke, Michael Wittler, Stefan Pischinger and Jens Bockstette
To gain insight into the collector-electrode interface in Li-ion batteries, a mesoscale model resolved at the particle scale in a representative volume element domain was developed. The underlying microstructure was first generated using a random packing and a dynamic collision algorithm. A finite element stress analysis was then used to calculate the deformations which are induced by Li-ion concentrations. The collector-electrode mechanical interaction was modeled using an adhesive contact law which was derived from the atomistic Lennard-Jones energy potential considering Van der Waals attractions. A finite element electrical analysis followed to calculate the collector contact resistance considering quantum tunneling currents. As a model application, we elaborated the role of the electrode microstructure by evaluating the damage and contact resistances for 8 various LiFePO4 based cathodes. We found that optimum interfaces would be achieved using a rough collector, low porosity, small particle sizes with disk like shapes and conductive additives in the interstitial sites. Pressure application was also beneficial. The developed model could be used either separately prior to commonly used porous electrode electrochemical models which require the collector-contact resistance as a parameter, or coupled in a 3D mesoscale electrochemical analysis so that a mechanical-electrochemical interaction would be considered.
A809
M. Pfanzelt, P. Kubiak, S. Jacke, L. Dimesso, W. Jaegermann and M. Wohlfahrt-Mehrens
X-ray photoelectron spectroscopy (XPS) and symmetric electrochemical impedance spectroscopy (EIS) are carried out to identify and determine the nature of the solid electrolyte interface (SEI) formation on TiO2 rutile anodes in lithium ion batteries. The recorded XPS spectra (O1s, C1s, P2p and Li1s and Ti2p) evidence an SEI layer formation at 0.8 V vs. Li/Li+ in a TiO2/Li cell with a lithium reference and an organic electrolyte (LiPF6 in EC : DMC (1 : 1 by wt%)). When the cell is discharged down to 0.1 V, the SEI mainly consists of ether and carbonyl groups and some alcohol or alkoxide groups. Upon charge the SEI additionally evidences some carboxylic groups. EIS measurements exhibit an additional RQ element at 0.8 V, supporting the formation of the SEI at this potential. The EIS evaluation shows that the SEI is mainly formed in the first cycle but evolves further on in the following cycles.
A815
Hsiao-Ying Shadow Huang and Yi-Xu Wang
It has been suggested that structural failures are the primary factor responsible for the observed rate-capacity fade of lithium-ion batteries. In the present study, we report three different lithium intercalation-induced dislocation mechanisms explaining experimentally observed cracks. We use the theory of elasticity and the superposition method to investigate stress and force fields between multiple dislocations. In most cases, dislocations are not perfectly parallel to one specific axis. Therefore, stress variations for arbitrary Burger's vectors are investigated. The stress fields manifesting between dislocations are numerically calculated and anisotropic material properties of electrodes are employed. The result shows that multiple dislocations are likely to be orthogonal to each other to reduce the total energy. In addition, studies have shown that when the discharging rate is increased, the capacity decreases due to the buildup of the internal elastic/plastic energy. Therefore, the stress fields of dislocation interactions in our study could be used to deduce and suggest the most feasible modes of crack formation and to provide insights into the lost of capacity in LiFePO4. Thus, the current study provide links between stress fields and the observed structural failure in lithium-ion batteries.
A822
R. Cornut, D. Lepage and S. B. Schougaard
In the present study, the importance of thorough active material and carbon mixing for the performance of LiFePO4 based electrodes was investigated experimentally and theoretically. A simple transformation of experimental data was introduced to identify the portion of the discharge curves that corresponds to an ohmic response. This section of the experimental data was subsequently modeled using a local Ohm's law to describe the transport in different media, including agglomerates. From the fitted data, it was shown that the mixing procedure has a profound effect on agglomerate size and size polydispersity. Further, an analytical approximation of the discharge curves integrating the agglomerates transport parameter and size distribution broadness was proposed in order to facilitate future comparison between experiments and model.
A828
Jianhua Liu, Junwei An, Yuxiao Ma, Mengliu Li and Rongbao Ma
A novel composite was obtained by hybridizing polypyrrole (PPY) nanotubes with chemically reduced graphene sheets, which comprehensively utilizes the advantages of electric double layer (EDL) capacitor and pseudo-capacitor. Scanning electron microscopy and transmission electron microscopy images revealed that graphene sheets in the graphene-polypyrrole (GP) composite obtained intimately interacted with PPY nanotubes. Raman and UV-vis spectra of the GP composite were measured and a solid interaction between graphene and PPY was observed. The electrochemical performance of the GP composite was evaluated and a specific capacitance of 400 F/g at a current density of 0.3 A/g was obtained; this capacitance is higher than that of a previously reported graphene-polypyrrole nanofiber composite. Furthermore, at a current density of 1.5 A/g, the specific capacitance of the GP composite fabricated in this work is as high as 324 F/g, suggesting its possible application in supercapacitors.
A834
Xiaofeng Zhang and Richard L. Axelbaum
Uniform, spherical powders consisting of nanostructured Li-excess Li(1+x)Ni0.25Mn0.75O(2.25+x/2) (0.375 ≤ x ≤ 0.5) were synthesized via a spray pyrolysis approach using mixed nitrate precursors. Among the materials produced, the layered Li1.5Ni0.25Mn0.75O2.5 (R
m) attained a capacity of over 250 mAhg−1, which is comparable to that of the Li-excess cathode materials produced via coprecipitation. Li content was varied and found to affect the crystal structure, morphology and electrochemical properties of the materials, and the sintering temperature increased with Li content. Li2MnO3-type structures were observed on XRD diffraction patterns at high annealing temperatures for x < 0.5 due to a phase transformation. The Li2MnO3-type structures degraded the electrochemical performance of these materials due to the high kinetic barrier for Li transportation. In particular, Li1.5Ni0.25Mn0.75O2.5 annealed at 800°C and Li1.375Ni0.25Mn0.75O2.4375 annealed at 700°C predominately adopted a layered composite structure. Nano-domains (5∼10 nm) of spinel structure were observed by HR-TEM to be structurally integrated with the layered structure for Li1.375Ni0.25Mn0.75O2.4375 annealed at 700°C. Nonetheless, the layered Li1.5Ni0.25Mn0.75O2.5 materials showed the best performance in terms of capacity, cycleability and rate-capability among these materials. The superior rate capability of these materials is aided by the nano-structured morphology, which consists of nano-sized primary particles and highly porous secondary particles.
A843
Zhijun Jia, Baoguo Wang, Shiqiang Song and Xiao Chen
Glycerin and n-propyl alcohol have been investigated as electrolyte additives for vanadium redox flow batteries (VRFB). The effects of these additives on the electrochemical performances of VRBF positive electrolyte were investigated by cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry. The results show an improved electrochemical performance upon the addition of glycerin. This is attributed to more effective adsorption of vanadium ions at the electrode surface, which, in turn, is due to the increased activity of the hydroxyl groups in the electrolyte.
A848
Tommy Georgios Zavalis, Mårten Behm and Göran Lindbergh
A short-circuited lithium-ion battery cell is likely to generate sufficient heat to initiate exothermic side reactions causing thermal runaway. A 2D coupled electrochemical-thermal model was developed to investigate a prismatic LiNi0.8Co0.15Al0.05O2|LiPF6, EC/EMC (3:7)|MAG-10 battery cell that is short-circuited. Three short-circuit scenarios are investigated during the events from when short circuit occurs until exothermic side reactions initiate. The scenarios are an external short circuit, a nail penetration and an impurity-induced short circuit. The model is used to predict the temperature increase within the cell and to explain how the interrelation between the electrochemical processes and the thermal properties affects the increase. Important safety measures are also examined with the model. The simulation results highlight general short-circuit characteristics and critical distinctions between the scenarios. The mass transport of lithium ions in the electrolyte is found to be the most important general characteristic that determines the rate of the temperature increase. The electric resistance distinguishes the scenarios from each other. The rate of the temperature increase is dictated by the mass transport in the electrolyte even when large variations in available active material are made and it is shown to be difficult to slow down the rate by cooling.
A860
Saeed Khaleghi Rahimian, Sean Rayman and Ralph E. White
The state of charge (SOC) and the loss of active material of the electrodes of a Li ion cell under Low Earth Orbit condition (LEO) have been estimated using Kalman filtering methods, by means of the physics-based single particle (SP) model. Zero mean Gaussian noise was added to the charge-discharge curves obtained by the SP model to generate synthetic data. Afterwards, nonlinear Filtering approaches including Extended Kalman Filtering (EKF) and Unscented Kalman Filtering (UKF) were applied to predict the true SOC and the electrodes’ degradation, by minimizing the measurement residuals between the model prediction and the synthetic data. The results indicated that UKF is a far superior candidate than EKF for the SOC estimation for a Li-ion cell during the cycling. Moreover, the proposed method is able to predict the loss of active material for each electrode during the cell life.
A873
Carmen M. López, John T. Vaughey and Dennis W. Dees
With a theoretical specific capacity of 3862 mAh/g and other desirable properties such as high voltage, light weight, and high energy density, metallic lithium remains one of the materials of greatest promise for advanced battery applications. However, the complicated reactivity of this electrode with most practical battery electrolytes leads to substantial morphological and chemical changes that affect the safety and efficiency of the system, and have prevented its further implementation on rechargeable batteries. In this work we demonstrate how to establish a direct and systematic relationship between such morphological changes in the lithium electrode and the cycle performance of the battery. We demonstrate that the main morphological changes are associated with the decomposition of the redox-formed SEI layer, which follows different electrochemical pathways leading to different morphologies depending on the cycling rate of the cell. At high cycling rates (i > 0.16 mAcm−2), a three-layer morphology (dendritic layer, porous layer, residual lithium layer) is observed. At low cycling rates (i ≤ 0.16 mAcm−2), polymerization of electrolyte's solvents and gas evolution leading to macroscopic bubble clusters is observed. Furthermore, we demonstrate the advantages of using these systematic morphology-property relationships to fit and interpret complicated electrochemical impedance spectroscopy (EIS) data.
A887
Chang Keun Back, Ri-Zhu Yin, Se-Jong Shin, Yoon-Soo Lee, Wanuk Choi and Yang-Soo Kim
Electrochemical properties and gas evolution behavior of Li2NiO2 are studied. In-situ gas evolution test of Li2NiO2 cell shows that large amount of gas is evolved during the first delithiation process at two characteristic potential levels of about 3.6 V and 4.13 V vs. Li/Li+ for small gas and severe gas generation, respectively. In-situ XRD and EXAFS analyzes reveal that the small gas generation is related to the bulk structural collapse of Li2NiO2 during phase transformation, while the severe gas generation results from the material decomposition of structurally unstable phase after the phase transformation. 3 wt% Al2O3 coated Li2NiO2 shows improved gas evolution properties.
A894
Zipeng Yan, Shu Cai, Xing Zhou, Yongming Zhao and Lijuan Miao
Nanostructured Li2FeSiO4/C composites have been successfully synthesized by adopting polyethylene glycol (PEG) as the surfactant and L-ascorbic acid as the carbon additive, using a sol-gel method based on the acid-catalyzed hydrolysis/condensation of tetraethoxysilane (TEOS). The Li2FeSiO4/C nanocomposites possess dispersed spherical particles (∼50 nm) with narrow particle size distribution, embedded in a continuous carbon matrix. The Li2FeSiO4/C nanocomposites deliver first discharge capacity of 138.2 mAhg−1 at C/16 and maintain at about 130.4 mAhg−1 after 40 cycles at various rates at room temperature, which outperform those of Li2FeSiO4/C samples synthesized without PEG. The electrochemical performances of Li2FeSiO4/C were largely enhanced after the introduction of PEG due to the following two aspects. On one hand, the smaller particle size facilitated the shorter diffusion length for lithium ions; On the other hand, the more continuous carbon film coated on the particle surface enhanced the electronic conductivity of the nanocomposites and restrained the side reaction occurring at the electrode-electrolyte interface.
A899
Ho-Seong Nam, Nae-Lih Wu, Kuang-Tsin Lee, Kwang Man Kim, Chul Gi Yeom, Lovely Rose Hepowit, Jang Myoun Ko and Jong-Duk Kim
Nanowire-structured MnO2 was synthesized by a sonochemical method and its electrochemical capacitances were investigated in three kinds of electrolytes: liquid-type KCl solution, potassium polyacrylate (PAAK), and potassium polyacrylate-co-polyacrylamide (PAAK-PAAM) gel polymer electrolytes (GPEs). The prepared MnO2 with a nanowire structure had a high specific surface area and narrow pore distribution, which was very useful for gel-type electrolyte in supercapacitor applications. The specific capacitance of nanowire-structured MnO2 with PAAK electrolyte exceeded 484 F g−1 at the conventional loading weight of MnO2 (1.02 mg cm−2) in the electrode. The nanowire-structured MnO2 with PAAK electrolytes was a very promising electrode material for high-performance supercapacitors.
A904
Joshua Lehr, Wesley M. Dose, Marina Yakovleva and Scott W. Donne
The effect of lithium concentration on LixMnO2 (x ≤ 0.3) materials prepared by co-precipitation/heating is investigated. Lithium concentration determines the phase formed, with three different phases identified in the concentration range. Low levels of lithiation (x = 0.08) leads to the formation of a γ/β type MnO2 material. As the lithium concentration is increased to x = 0.15, a lithiated γ−MnO2 like phase is formed. Finally, at x = 0.28 tunnel structured monoclinic MnO2 is obtained. Increasing the concentration of lithium inhibits the formation of the undesired inactive Mn2O3 phase, which is formed upon heat-treatment of MnO2. At a 5 mA/g charge/discharge rate the monoclinic Li0.28MnO2 material gave the best performance, while at 30 mA/g the Li0.08MnO2 material proved superior.
A909
Christopher Joyce, Lynn Trahey, Sara A. Bauer, Fulya Dogan and John T. Vaughey
High capacity anode materials for lithium-ion batteries typically experience large crystallographic volume expansions due to formation of either alloy or Zintl LixM phases. This phenomena has been observed for several main group metals, including tin, silicon, and germanium, that are being considered for next generation anode materials. Solutions proposed include new morphologies, precursor phases, and organic binders but none have displaced previous binders because of higher costs or they introduce inactive or poorly conducting phases that hurt performance. In this report we have studied an alternative method of binding electrochemically active silicon to the current collector based on a method that utilizes copper as a replacement for both the binder and conductive additive in a standard electrode. For this system we have optimized conditions to maximize the adhesion of the silicon to the copper foil current collector while minimizing formation of binary intermetallic compounds. For compositions around Cu: 4 Si (64 wt% Si), the electrochemical cycle life is comparable to electrodes made using a PVDF polymer binder but with one-third the overall electrode resistance.
Fuel Cells and Energy Conversion
B647
J. Yablecki, A. Nabovati and A. Bazylak
In this paper the anisotropic effective thermal conductivity of the gas diffusion layer (GDL) of polymer electrolyte membrane fuel cell is determined using the two- and three-dimensional two-phase conjugate fluid-solid thermal lattice Boltzmann model. Using stochastic reconstructions of the GDL, the effective thermal conductivity is evaluated in the through-plane and in-plane directions. It is shown that the anisotropic structure of the GDL results in an anisotropic thermal conductivity, with a higher value for the in-plane thermal conductivity than the through-plane thermal conductivity. We show that the two-dimensional in-plane simulations provided reasonable estimates of the thermal conductivity at a significantly lower computational cost than the three-dimensional simulations. Adding the third dimension, however, dampens the effect of structure randomness and reduces the variance in the predicted data points. The predicted values of effective through-plane thermal conductivity from two-dimensional simulations are almost one order of magnitude smaller than those predicted from three-dimensional simulations. The fibers are better connected in the three-dimensional reconstructed structures, which create a preferential path for heat transport, and thus a higher effective thermal conductivity. The predicted values of effective thermal conductivity are in good agreement with previously reported values in the literature.
B654
Jingjie Wu, Fengjie Xia, Mu Pan and Xiao-Dong Zhou
Simultaneous electrochemical activity and kinetic stability of the electrode materials are of paramount importance to the commercialization of proton exchange membrane fuel cells. In this paper, we report a new material, titanium disilicide (TiSi2), to support nano Pt electrocatalysts that were synthesized via a colloidal approach. Accelerated durability test (ADT) shows that the oxygen reduction electrode made of Pt/TiSi2 exhibits substantial improvement over commercial Pt/C electrode in terms of the kinetic stability. After 2000 ADT cycles, the electrochemical surface area of Pt/TiSi2 decreases to ∼73% of the initial magnitude, compared to 36% of Pt/C electrodes. The ADT results are consistent with the analysis of Pt particle size by transmission electron microscopy, which shows aggregation of Pt nanoparticles in Pt/C and marginal growth of Pt with TiSi2 as the support. Oxygen reduction reactions on Pt/TiSi2 take place via a four-electron electrochemical process. A similar Tafel behavior is observed in Pt/TiSi2 and Pt/C electrodes, suggesting the presence of similar oxygen reduction mechanisms in both electrodes.
B661
Mingfei Liu, Dong Ding, Yaohui Bai, Ting He and Meilin Liu
Doped ceria has been widely studied as electrolyte materials for intermediate temperature solid oxide fuel cells (IT-SOFCs). While high peak power densities have been reported, the electronic conductivity of doped ceria under fuel cell operating conditions reduces the open circuit voltage (OCV) and hence energy efficiency, more so with thinner electrolyte membrane at higher operating temperatures. Here we report a new cell structure: a thin SDC electrolyte membrane supported by a composite anode consisting of a mixed-ion conductor BaZr0.1Ce0.7Y0.1Yb0.1O3−δ (BZCYYb) and NiO. The inter-diffusion between BZCYYb and SDC during co-firing results in a thin layer of doped barium cerate and zirconate at the interface, which suppresses the electronic conduction of SDC and enhances the OCV and cell performance. The new cell structure also shows excellent stability when wet hydrogen or methane was used as fuel at 750°C.
B666
Aligul Buyukaksoy, Vladimir Petrovsky and Fatih Dogan
The long term performance of SOFC with nanocomposite Ni-YSZ anode and LSM-YSZ cathode was reported. The SOFC was prepared by infiltrating polymeric precursors of NiO and LSM from anode and cathode sides respectively. The fuel cell showed relatively high initial performance (0.49 Watt/cm2 at 800°C) for the given electrolyte thickness (∼170 μm). Long term stability tests showed that the power density dropped to 0.41 Watt/cm2 in the first 60 hours of operation in short circuit conditions and no further change in the power density was observed. Low electrode polarization resistance was obtained (∼0.080 Ohm.cm2 for combined anode and cathode at 800°C) which showed no significant change with prolonged time. The slight drop in power density was related to the change in ohmic resistance which was attributed to the increase in current collection resistance. The fact that the majority of the resistance was due to the electrolyte resistance (∼80%) suggests that stable SOFCs with high power densities could be achieved with thinner electrolytes. After >100 hours of operation at 800°C in short circuit conditions, the fuel cell was measured at higher temperatures. Power densities were 0.71 Watt/cm2 and 1.0 Watt/cm2 at 900°C and 1000°C, respectively.
B670
J. E. Harlow, D. A. Stevens, R. J. Sanderson, G. C.-K. Liu, L. B. Lohstreter, G. D. Vernstrom, R. T. Atanasoski, M. K. Debe and J. R. Dahn
The electrochemical behavior of Pt1−xMnx (0.1 < x < 0.8) catalysts prepared by magnetron sputtering were studied extensively using the rotating disk electrode technique, electron microprobe, X-ray photoelectron spectroscopy and X-ray diffraction. The data suggests that Mn forms an oxide layer at the surface of the catalyst upon contact with air. Mn is preferentially drawn out of the intermixed catalyst into the oxide layer, depleting the core of Mn content. Without significant amounts of Mn present at the core of the catalyst, de-alloying reactions have less effect on the electrochemically active surface area compared to the case of Pt1−xNix, for example. High and low Mn content alloys have about the same Pt-area specific current densities, jspecific, so it is likely that all samples have the same catalytic surface composition, namely Pt.
B677
Katrin Schlögl, Marianne Hanzlik and Matthias Arenz
The identical location transmission electron microscopy (IL-TEM) approach is used for a comparative study of the degradation of several standard Pt-based electrocatalysts for low temperature proton conducting membrane fuel cells (PEMFCs). By comparing the quantitative Pt surface area loss with IL-TEM micrographs, it is shown that in accelerated stress tests particle migration and coalescence as well as particle detachment are the main degradation channels for the chosen catalysts. No unambiguous indication for a major contribution of Pt dissolution to the surface area loss is found. Furthermore, it is demonstrated that seemingly similar catalysts can exhibit under identical treatment pronounced differences in their degradation behavior. A finding questioning the common praxis of comparative catalyst studies without full disclosure and discussion of their synthesis.
B683
A. Grimaud, F. Mauvy, J. M. Bassat, S. Fourcade, L. Rocheron, M. Marrony and J. C. Grenier
Four mixed ionic-electronic conducting (MIEC) perovskite-related oxides were studied as potential H+-SOFC cathode materials: La0.6Sr0.4Fe0.8Co0.2O3−δ, Ba0.5Sr0.5Co0.8Fe0.2O3−δ, PrBaCo2O5+δ and Pr2NiO4+δ. Their hydration properties were measured by TGA: Ba0.5Sr0.5Co0.8Fe0.2O3−δ shows the largest water uptake. Their electrochemical performances were characterized using BaCe0.9Y0.1O3−δ as electrolyte; polarization resistances as low as 0.5 Ω cm2 were found at 600°C, for PrBaCo2O5+δ and Pr2NiO4+δ. The rate determining steps of the oxygen reduction reaction were determined on the basis of electrochemical studies performed as a function of pH2O, in air. Proton transfer and water release appear to be the rate determining steps for Ba0.5Sr0.5Co0.8Fe0.2O3−δ, PrBaCo2O5+δ and Pr2NiO4+δ. No rate determining step involving proton was found for La0.6Sr0.4Fe0.8Co0.2O3−δ. On the basis of this study, one can suggest that Ba0.5Sr0.5Co0.8Fe0.2O3−δ, PrBaCo2O5+δ and Pr2NiO4+δ show some protonic conduction as well as oxide diffusivity and can be labeled Triple Conducting (e-/O2−/H+) Oxides, so-called TCO.
B695
Moustafa Aboushabana, Norma R. de Tacconi and Krishnan Rajeshwar
Acid digestion and oxidation with H2O2 were investigated as chemical pre-treatments that could improve the generation of H2 from coal as well as carbon black slurries by electrolysis. Among the different 1 M acids that were used in this study, namely HClO4, H2SO4 and HNO3, digestion of Texas lignite coal (TXLC) with HClO4 was found to yield the best results. It increased the polarization time (and hence the amount of H2 generated at the cathode) during the galvanostatic polarization experiments by 50% compared to the untreated TXLC sample. On the other hand, acid digestion of carbon black (SRC-401) adversely affected the polarization time in all cases with a maximum reduction in polarization time (50%) in the case of HNO3. H2O2 treatment of medium (DECS10) and high rank (DECS21) coals did not improve the galvanostatic polarization behavior of their respective slurries, while low rank coals such as TXLC showed a moderate increase in the polarization time. This modification of the galvanostatic polarization behavior as a result of both types of chemical pre-treatments was correlated with changes in the surface area and/or surface functional groups as well as solubilization of the inherent mineral content in the coal samples. Finally simultaneous thermogravimetric and differential scanning calorimetric analyzes afforded insights into the consequences of the chemical pre-treatments on the thermal reactivity of the coal and carbon black samples.
B702
Nebojša Čebašek, Reidar Haugsrud, Jovan Milošević, Zuoan Li, Jens B. Smith, Anna Magrasó and Truls Norby
The growth of La2NiO4+δ at the interface between La2O3 and NiO has been studied from 950 to 1450°C in argon, air and oxygen. The thickness, microstructure and composition of the formed La2NiO4+δ layers have been characterized by means of SEM, EDX, EBSD, EPMA and XRD. The growth rate follows parabolic kinetics. It has been concluded from the position of Pt markers that La2NiO4+δ grows predominantly by solid state diffusion of Ni2+, and the experimental results were accordingly fitted with Wagner's expressions for self-diffusion. Above 1100°C the diffusion coefficients follow Arrhenius-type temperature dependencies, with activation energies 243 ± 21 and 218 ± 21 kJ/mol evaluated for the conditions at the La2O3/La2NiO4+δ and NiO/La2NiO4+δ interfaces, respectively. Below 1100°C the diffusivity falls more steeply with decreasing temperature, and possible explanations are discussed. Compared to cation diffusion in perovskite-type oxides, Ni2+ diffusivity in La2NiO4+δ is in higher range.
B709
Hanno Butsch, Christina Roth, Dietrich Ritzinger, Gregor Hoogers and Achim Bock
A device and a method for direct measurement of the local contact pressures of gas diffusion layers (GDL) are presented. The new tool determines the spatially resolved contact pressure on the GDL side opposite to the flow-field/GDL interface which is relevant to good electrical contact between the GDL and the catalyst coated membrane (CCM) in a practical fuel cell setting. In a second step, using a fit function determined by separate two and four point resistance measurements, the method is extended to deliver spatially resolved contact resistance data. These experimental methods, in addition to shear-force measurements, are applied to a range of state-of-the-art GDL media. Whereas the shear-force measurements correlate well with data from recent work in the literature, the comparison of a non-woven and a paper based GDL with distinct differences in their shear moduli shows almost the same contact pressures underneath the flow field channel. This result indicates that shear-force data alone is of limited use for predicting contact pressure underneath flow field channels. In-situ current/voltage curves confirm the predictive power of a direct measurement of the contact pressure which highlights the importance for future GDL development and modeling activities.
B714
Alireza Torabi and Thomas H. Etsell
Single cells based on Ni-CeO2-WC-YSZ anodes were investigated as an alternative material for direct methane solid oxide fuel cells. First, a YSZ electrolyte-based cell with porous YSZ as the support for electrode materials on both sides was prepared. Then electrocatalyst materials were incorporated into the porous YSZ: the anode was infiltrated with WC (25 vol.%), Ni (5 wt%) and ceria (5 wt%) precursors; and the cathode with LSM (20 vol.%) precursor. A Ni-CeO2-WC-YSZ symmetrical cell study showed that the Ni modified electrode performed stably with humidified methane at 850°C for a period of 48 hours under open circuit condition; no carbon formation was observed either with in-situ impedance spectroscopy or ex-situ scanning electron microscopy. Furthermore, the fuel cell results revealed that not only does the anode operate steadily with a reasonable performance on methane fuel, but the stability of the carbide phase is well maintained. The cell also successfully survived an oxidation-reduction-recarburization cycle. It was demonstrated that with a proper cell configuration, the structural integrity can be protected. These results suggest that a Ni modified anode is compatible with methane fuel, with reasonable and stable performance.
B723
Yanhai Du, Daan Cui, Kenneth Reifsnider and Fanglin Chen
For portable applications, a fuel cell often experiences frequent startups and shutdowns. Therefore the startup and shutdown behaviors are critical to a portable solid oxide fuel cell (SOFC) and SOFC system. Startup characteristics of four propane-fueled hot zones were investigated. The hot zones were able to be started up at environmental temperatures of 50°C, 40°C, 30°C, 20°C, 0°C, −10°C, −20°C and −30°C, respectively, without the need of additional heat source. The effect of the environment temperatures on the startup times for the stacks to reach operating temperatures (700°C for example) was negligible (within 3 minutes). The hot zone temperatures, however, decreased when decreasing the environmental temperatures from 50°C to −30°C, and stabilized at 661–635°C (CPOX), 763–745°C (stack) and 785–733°C (TG) after one hour from startup. The maximum power of the hot zones was 165 W at over 60% fuel utilization.
B729
Wisam J. Khudhayer, Nancy Kariuki, Deborah J. Myers, Ali U. Shaikh and Tansel Karabacak
Vertically aligned chromium nanorod arrays were grown on glassy carbon electrodes by a dc magnetron sputtering glancing angle deposition (GLAD) technique. The Cr nanorods were used as low-cost, high surface area, metallic supports for a conformal Pt thin film, resulting in a potential low-loading electrocatalyst for the oxygen reduction reaction (ORR) in polymer electrolyte membrane (PEM) fuel cells. Conformal coatings of Pt on Cr nanorods were achieved using a dc magnetron sputtering small angle deposition (SAD) technique. The electrocatalytic ORR activity of SAD-Pt/GLAD-Cr electrodes was investigated using cyclic voltammetry and rotating-disk electrode techniques in a 0.1 M HClO4 solution at temperatures ranging from 20 to 60°C, and was compared to those of GLAD Cr nanorods coated with Pt thin film deposited at normal and large angles of incidence. The results show that SAD-Pt/GLAD-Cr nanorods exhibit higher values of electrochemically-active surface area (ECSA), area- and mass-specific activities, and better stability against loss of ECSA during potential cycling in the acidic electrolyte. The improved ORR activity and enhanced catalyst utilization of SAD-Pt/GLAD-Cr electrode might be attributed to a better Pt conformality, especially at the sidewalls of the nanorods, and a preferential exposure of certain crystal facets.
B737
Chaozhong Qin, S. Majid Hassanizadeh, Dirk Rensink and Stephan Fell
The mathematical description of liquid water flooding in the gas channel (GC) of a polymer electrolyte fuel cell (PEFC) at the macro scale has remained a challenge up to now. The mist flow assumption in the GC has been commonly used in previous numerical studies. In this work, a one-dimensional (down-the-channel) macroscale phenomenological model for the liquid water flooding in the cathode GC is developed based on several reasonable assumptions. We focus on the operating conditions with fully humidified inlet air on the cathode side. Some simplifications are introduced to obtain a manageable numerical model. A series of case studies are conducted to investigate the effects of droplets and various operating parameters on the liquid water flooding in the GC. The results show that the gas drag force at the film-gas interface significantly enhances the film flow along the GC corners. Based on a proposed droplet model, we can capture key scenarios of liquid water flooding in the GC under different operating conditions like varying stoichiometry, current density and cell temperature. We find that droplets in the GC mainly contribute to the gas pressure loss and water flooding in the GC, which should be depressed for better water management. At last, a proper selection of the GC sidewall contact angle is found to be critical to a better water management in the GC.
B746
Xiaoyu Ding, Sima Didari, Thomas F. Fuller and Tequila A. L. Harris
A new fabrication process to manufacture a membrane electrode assembly (MEA) by extrusion slot coating of ionomer onto a catalyzed gas diffusion layer (GDL) is presented. Preliminary coating tests were conducted to study the feasibility and effectiveness of directly coating Nafion D2021 onto catalyzed Toray 060 carbon paper. The uniformity of the coated membrane and the penetration of the Nafion dispersion into the catalyst layer were analyzed. Pressing and blowing operations were introduced into the fabrication process to increase the membrane uniformity and to decrease the penetration of Nafion dispersion. The effects of these operations were analyzed. The performance of MEAs fabricated using the new process was measured and compared with MEAs made by traditional methods. It was found that MEAs formed by direct coating have similar electrochemical performance at current densities below 0.8 A/cm2 as MEAs traditionally fabricated.
B754
Lisa M. Onishi, John M. Prausnitz and John Newman
Steady-state diffusion coefficients of water in Nafion were determined in the absence of inert gases at 25°C. A large range of water activity was investigated to determine average and differential diffusion coefficients. Flux decreased toward zero as the water activity gradient between water vapor and liquid water approached zero, indicating no Schroeder's paradox. The average diffusion coefficients varied between 1 × 10−6 and 5 × 10−6 cm2/s, with a minimum at 14 moles H2O/mol SO3−. Differential diffusion coefficients ranged between 4 × 10−7 and 2 × 10−5 cm2/s, with a minimum at 14 moles H2O/mol SO3−.
B761
Matt S. Naughton, Akash A. Moradia and Paul J. A. Kenis
Fuel cells are gaining increasing attention as portable power sources due to their inherent efficiency advantages. Many aspects of electrode and catalyst behavior within an operating fuel cell, however, are still not well-understood. The major divide between catalyst-based rotating disk electrode experiments and full-cell experiments can lead to disappointing results when a promising catalyst is tested in a fuel cell. Here, using a flowing electrolyte-based microfluidic H2/O2 fuel cell with a reference electrode, we demonstrate the ability to analyze single-electrode performance in-situ using a novel analysis protocol that provides kinetic parameters Rohmic and ηkinetic to quantify individual electrode data. Using this protocol, we determine the mass transport and ohmic effects on these kinetic parameters and correlate them with actual fuel cell performance. We also compare the performance of identical electrodes in alkaline and acidic media using both our analytical method and electrochemical impedance. The quantitative parameters are show to predict power density within 5% for measured data and were then used to predict performance for a newly assembled fuel cell, which was accurate within 10% of actual power density inside the measured range. In summary, the analytical method reported here can improve the understanding of in-situ electrode behavior.
Corrosion, Passivation, and Anodic Films
C253
Z. Grubač, I. Škugor Rončević, M. Metikoš-Huković, R. Babić, M. Petravić and R. Peter
The use of self-assembling monolayers (SAM) of long chain carboxylic acids has a potential for designing specific interface architectures in degradable implants technology. In this paper, the native and anodically formed oxide films on the Mg‑alloy (AZ91D) surface were modified with the SAMs of palmitic acid (PA) and stearic acid (SA) to protect the alloy degradation in a physiological solution. X‑ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) were used to evaluate chemical composition, bonding modes of acids to the substrate, and structural properties (ordering and close-packing) of the surface layers. The results obtained by electrochemical impedance spectroscopy (EIS) have shown a beneficial effect of anodization and especially of the oxide layer modification by forming SAMs of PA and SA on the corrosion properties of AZ91D alloy in physiological solutions.
C259
N. Missert, R. G. Copeland, C. M. Johnson and J. C. Barbour
Corrosion of aluminum in a system of engineered copper particles was studied in order to elucidate the nature of the interactions between multiple pitting sites. Single copper particles were fabricated on isolated, thin-film aluminum electrodes to enable independent measurements of excess anodic and cathodic currents flowing during open circuit exposures to dilute aqueous chloride solutions. In-situ fluorescence microscopy allowed imaging of local changes in solution pH during the exposure. Under the experimental conditions explored here, the anodic dissolution of aluminum beneath the majority of particles was balanced by cathodic reactions on the same electrode. However, excess anodic currents were also observed on some single electrodes due to accelerated dissolution of aluminum beneath the copper particles. These excess anodic currents were balanced by cathodic currents distributed between the other electrodes. Fluctuations in the excess anodic currents were correlated with fluctuations in the open circuit potential and with localized increases in solution pH above each of the copper particles. The transient nature of this accelerated dissolution suggests that it may evolve under anodic control.
C265
N. Murer, N. A. Missert and R. G. Buchheit
Finite element modeling based on solving the Nernst-Planck equation was used to describe the evolution of current densities and pH distribution at the surface of a bimetallic system. This system consisted of five single copper particles fabricated on isolated, thin-film aluminum electrodes exposed to dilute aqueous chloride solutions. Excess anodic and cathodic currents flowing during exposure were used to validate the model. The corrosion of the bimetallic system exhibited a passive and an active stage. The model was used firstly to quantify the influence of pH (modified by alkalization by O2 reduction at the cathodes and acidification by Al3+ hydrolysis) on the passive-active transition and secondly to verify the anodic control of the active corrosion. EQCM (Electrochemical Quartz Crystal Microbalance) was used to obtain an experimental relationship between Al dissolution rate and pH. In the conditions of the model, Al3+ hydrolysis was found to activate Al dissolution in the early instants of exposure (≈10 s) whereas OH− would have an effect only at longer times (hundreds of s). The pH-related destabilization appeared not to be sufficient enough to trigger active dissolution and it was proved that this stage was controlled by the anodic activity and not O2 diffusion.
Electrochemical/Chemical Deposition and Etching
D341
Sunjung Kim and Luda Lee
Cu-Co alloy substrate was formed on the Au-seeded p-GaN side of sapphire wafer specimens to function as a secondary substrate of vertical structure GaN-based light emitting diode (LED), using electrodeposition method at constant potentials in an acidic citrate electrolyte. Potentiostatic deposition process was available to change the Co content of Cu-Co alloy substrates with varying cathodic deposition potential. Rotation speed of wafer specimens during electrodeposition also affected seriously the microstructure as well as Co content of the substrates. Cu-Co alloy layers deposited on non-rotating specimens showed coarse, particulate microstructures, whereas Cu-Co alloy substrates formed with applying specimen rotation had dense, grained microstructures. The chemical composition and microstructure of electrodeposited Cu-Co alloy substrates were closely related with their electrical and mechanical properties, which should be essentially considered for a appropriate secondary substrate of vertical structure LEDs. Residual stress, electrical resistivity, and Vickers hardness of the substrates were measured, respectively, according to cathodic deposition potential and rotation speed. In conclusion, mechanically strengthened Cu-Co alloy substrate in comparison with ductile Cu substrate was fabricated having very low residual stress and acceptable electrical resistivity by alloying Cu with low Co content of less than 3.15 at% in potentiostatic deposition process.
D347
E. Chassaing, N. Naghavi, M. Bouttemy, V. Bockelee, J. Vigneron, A. Etcheberry and D. Lincot
The electrochemical deposition of indium sulfide layers is investigated with the aim of replacing cadmium sulfide layers in copper-indium-gallium diselenide thin film solar cells. In this paper the deposition conditions are first investigated from theoretical solution chemistry analysis. Experiments are then carried out using Mo-coated glass conducting substrates and gold-coated electrochemical quartz crystal microbalance. Indium chloride acidic aqueous solutions (pH ∼ 3.5–4) containing thiosulfate ions as the sulfur source are used. Cyclic voltammetry studies are carried out. A potential domain is determined which allows to deposit compact layers. XPS analysis indicates the presence of both sulfur and oxygen in the films. The double structure of the O 1s spectra and the particular S 2p energy dispersion suggest two distinct chemical environments for indium whose respective prominence depends on the deposition potential. At low overpotential, an indium sulfide layer containing oxygen species (O, OH) is predominantly identified whereas at more negative potentials a second environment attributed to the presence of sulfate-type (SOx) groups emerge. These results are discussed in relation to solution chemistry analysis and possible reaction paths are proposed.
D355
Hoo Keun Park, Sung Pyo Hong and Young Rag Do
In this study, ZnO nanorods were grown on indium-tin oxide (ITO)-coated glass substrate using a hydrothermal-electrochemical method in a Zn(NO3)2 aqueous solution. To optimize the properties of ZnO nanorods grown on the ITO-coated glass substrate, the effects of growth parameters, such as the thickness of ZnO seed layer (0–70 nm), the addition of NaOH additive, the applied potential (−0.6–−1.2 V), and the growth temperature (120–180°C) were examined with respect to the morphological, structural, photoluminescence, and transmittance properties of the nanorods. An improvement in the UV–visible ratio of the ZnO nanorods was obtained by increasing the thickness of the seed layer and by increasing the applied potential and the growth temperature with the addition of a NaOH solution. Based on the combined results of this study, the vertical ZnO nanorods produced on the ITO-coated glass substrate hold great promise for use in the development of high-performance optoelectronic devices and other applications.
D362
Yu-Chung Chen, Feng-Ching Hsiao, Bo-Wen Lin, Bau-Ming Wang, YewChung Sermon Wu and Wen-Ching Hsu
A two-step chemical wet etching processes were used to investigated the formation and the plane indexes of exposed etched facets of wet etching patterned sapphire substrate (PSS). It was found when SiO2 mask still remained on the top c-plane, the structure of PSS comprised of a hexagonal pyramid covered with six facets
with a flat top c-plane. When SiO2 mask were etched away, beside six facets on the bottom, there were 3 extra facets
exposed on the top.
D367
Liang-Hsun Lai, Ke-Jie Huang, Sham-Tsong Shiue, Jing-Tang Chang and Ju-Liang He
When ethylene/nitrogen (C2H4/N2) mixtures are used to deposit carbon films by thermal chemical vapor deposition (CVD), effects of C2H4/(C2H4 + N2) ratios on the deposition rate and microstructures of carbon films are investigated. Experimental results reveal that the deposition rate of carbon films increases with the C2H4/(C2H4 + N2) ratio, and also, raises with the residence time, deposition temperature, and working pressure. The kinetics of this thermal CVD process is discussed. The deposition rate of carbon films is proportional to the C2H4/(C2H4 + N2) ratio with a power of second order, which is resulted from the adsorption of remaining precursor gases C2H4 on the silica glass plate substrate. Few nitrogen and hydrogen atoms are incorporated into carbon films. As the partial pressure of C2H4 is smaller than a threshold pressure or the residence time is shorter than a threshold residence time, no film is formed. The activation energy (= 448 kJ/mole) of carbon deposition is related to the activation energy of C2H4 dissociation. The degree of ordering and nano-crystallite size of carbon films decrease with increasing the C2H4/(C2H4 + N2) ratio, while the sp3 carbon atoms of carbon films increase. Finally, the results of thermal CVD carbon deposition using C2H4 are compared with those using methane and acetylene.
D375
Yan Liu and Wei Wang
Investigation on the Cu(II) and Co(II) electrochemical reduction kinetics in citrate solution provides important theoretical guidance for the preparation of Cu-Co alloy materials. Kinetics of Cu(II) and Co(II) co-electrodeposition in citrate solution was investigated by Cyclic Voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS). To bring the reduction potentials of Cu(II) and Co(II) closer, various citrate concentrations, pH values, cobalt concentrations and copper concentrations were studied. Preliminary study on the molecular structure of the complexes was performed by Fourier transform infra-red spectra (FT-IR). Results show that the reduction potentials of Cu(II) and Co(II) is close in solutions comprised of 0.05∼0.15 M CuSO4·5H2O, 0.05 M CoSO4·7H2O, 0.20 M C6H5Na3O7·2H2O, 0.20 M Na2SO4 or 0.05 M CuSO4·5H2O 0.05∼0.20 M CoSO4·7H2O, 0.20 M C6H5Na3O7·2H2O, 0.20 M Na2SO4 with pH at about 6. The Cu(II)-citrate and Co(II)-citrate are first reduced to an intermediate state and then to Cu0 and Co0. Adsorption exists at the surface of the electrode. The complex is multidentate because ring formed indicating by IR.
D382
Yeung Au, Qing Min Wang, Huazhi Li, Jean-Sebastien M. Lehn, Deo V. Shenai and Roy G. Gordon
Through-silicon vias (TSV) will speed up interconnections between chips. Manufacturable and cost-effective TSVs will allow faster computer systems. In this paper, we report the successful formation of seed layers for plating copper TSVs with aspect ratios greater than 25:1. Following the rapid atomic layer deposition (ALD) of a conformal insulating layer of silica inside the silicon vias, manganese nitride (Mn4N) is deposited conformally on the silica surface by chemical vapor deposition (CVD). Mn4N forms an effective copper diffusion barrier and provides strong adhesion between the silica and the subsequently-deposited copper. Conformal copper or copper-manganese alloy films are then deposited by an iodine-catalyzed direct-liquid-injection (DLI) CVD process. Diffusion of manganese during post-deposition annealing further enhances the barrier and adhesion properties at the copper/dielectric interface.
D386
Nathan Fritz, Hyo-Chol Koo, Zachary Wilson, Erdal Uzunlar, Zhongsheng Wen, Xinyi Yeow, Sue Ann Bidstrup Allen and Paul A. Kohl
In this study, the electroless deposition of copper and silver was investigated on epoxy and silicon dioxide-based substrates. A cost-efficient, Sn/Ag catalyst was investigated as a replacement for the Sn/Pd catalyst currently used in board technology. The surface of the epoxy based polyhedral oligomeric silsesquioxane (POSS) films was modified by plasma and chemical etching for electroless activation without the creation of a roughened surface. The electroless copper deposited on the modified POSS surface exhibited excellent adhesion when annealed at 180°C in nitrogen for 90 min or at room temperature for 24 hr. Electroless copper deposition was also demonstrated on oxidized silicon wafers for through silicon via sidewall deposition.
D393
V. C. Nguyen, C. Y. Lee, L. Chang, F. J. Chen and C. S. Lin
In this study, the internal stress of Ni coating electroplated in the supercritical-CO2 (Sc-CO2) mixed Watts bath was investigated with a focus on the effects of plating parameters and additives. Both the internal stresses of the Ni coatings and their corresponding microstructures were examined. A relationship is found that the internal stress of the Ni coating was inversely proportional to its grain size and the Ni{200}/Ni{111} peak fraction in the measured X-ray diffraction pattern. The smaller grain size, accompanied with higher Ni{111} intensity, resulted in the higher internal stress of the coating, and vice versa. A proposed theoretical model, which took both the grain size and preferred crystalline orientation into account, correlated closely with experimental results in the internal stress. As a result, the presence of surfactant in the Sc-CO2 electrolyte increased the internal stress of Ni coating. However, a reduction of internal stress is made possible by varying four factors: the raising of current density, the increasing of plating temperature, the lowering of plating pressure, and the addition of saccharin into electrolyte. A comparison to the internal stress of Ni coatings plated by the conventional method was also discussed in this study.
Electrochemical Synthesis and Engineering
E115
Murat Ates, Ipek Osken and Turan Ozturk
3,5-Dithiophene-2-yldithieno[3,2-b;2′,3′-d]thiophene (Thy2DTT) and ethylenedioxythiophene (EDOT) were electro-copolymerized on glassy carbon electrode (GCE) in 0.1 M sodium perchlorate (NaClO4)/acetonitrile (ACN)/dichloromethane (CH2Cl2) (8:2) solution. Poly(Thy2DTT-co-EDOT)/GCE thin film was characterized by various techniques, such as Cyclic Voltammetry (CV), Fourier Transform Infrared Spectroscopy – Attenuated Transmittance Reflectance (FTIR-ATR), Scanning Electron Microscopy - Energy Dispersive X-ray analysis (SEM-EDX) and Electrochemical Impedance Spectroscopy (EIS). The effects of monomer mole fractions (mole fraction, XThy2DTT = nThy2DTT/nEDOT + nThy2DTT) (0.5, 0.66 and 0.83) during the preparation of modified electrodes were examined by EIS. Capacitive behaviors of the modified GCE were defined via Nyquist, Bode-magnitude, Bode-phase and Capacitance plots. The circuit model was used to fit the theoretical and experimental data through Kramers-Kronig Transform test. The lowest frequency capacitance (CLF) value was obtained as CLF = 0.89 mFcm−2 for poly(Thy2DTT). However, the highest CLF was obtained for the copolymer as CLF = 1.11 mFcm−2 for XThy2DTT = 0.66 and 0.83. Potential application of the copolymer could be energy-storage devices.
E122
Rong-Hsin Huang, Wen-Kai Chao, Ruei-Sung Yu, Rong-Tan Huang, Kan-Lin Hsueh and Fuh-Sheng Shieu
Silver nanoparticles (AgNPs) were successfully synthesized via a rapid and convenient electrochemical method using sodium montmorillonite (MMT), a naturally occurring mineral, as both a stabilizer and a carrier. X-ray diffraction results showed that the AgNPs had face-centered cubic crystal structure. Inductively coupled plasma-atomic emission spectral analysis indicated that the AgNP yield increased with increasing the reduction potential. UV-vis absorption curves demonstrated that the AgNPs had optical absorbance at ca. 412 nm and showed a spectral blue-shift resulting from a decrease in the particle size. Transmission electron microscopy confirmed that after a centrifugation clarification process, the AgNPs formed in the aqueous solutions at reduction potentials of 5, 10, 15, and 20 V had average sizes of 4.2, 5.6, 15.3, and 20.5 nm, respectively. In contrast, in the as-prepared AgNP/MMT aqueous solutions, the AgNPs on the MMT surface had average sizes of 5.1, 8.0, 17.0, and 25.0 nm at reduction potentials of 5, 10, 15, and 20 V, respectively. Measurement of the inhibition area of antibacterial activity demonstrated that the AgNP/MMT nanocomposites had promising antibacterial applications.
E127
Hanieh Ghadimi, Abdussalam Salhin Mohamed Ali, Norita Mohamed and Sulaiman Ab Ghani
The electrochemical oxidation of catechol in the presence of TSC in buffer solution (pH 5.3) was studied by cyclic voltammetry and controlled potential coulometry. The controlled potential coulometry was carried out with composite graphite working electrode. The oxidation mechanism was then suggested. The electro-generated o-quinone had a 1, 4-addition reaction with the available thiosemicarbazide, such that an increase in the current, which was attributed to the re-oxidation of the thiol-catechol adduct, could be used as a mean of quantifying the thiol. The electrochemical reaction which produced quinoid intermediates and their subsequent reaction with sulphydryl compounds have been investigated and were later quantified. The concentration of thiosemicarbazide in aqueous solutions was determined according to the linear dependence of the anodic peak current with concentration. The calibration plot was linear in the ranges of 1 × 10−5 to 8.5 × 10−4 mol L−1 with linear regression coefficient (R2) of 0.995. The relative standard deviation of the determination was 2% (n = 6).
E132
Hamid Mohammad Shiri and Mustafa Aghazadeh
Capsule-like NiO nanoparticles were prepared by heat-treatment of the cathodically electrodeposited nickel hydroxide at 300°C for three hours. The hydroxide precursor was deposited galvanostatically onto the stainless steel substrate from aqueous Ni(NO3)2 solution (0.01 M). Morphological, structural and chemical characteristics of the synthesized NiO were examined by means of scanning and transmission electron microscopy (SEM and TEM) as well as X-ray diffraction (XRD) and FT-IR spectroscopy. The XRD and TEM results revealed that the oxide products have well-crystallized cubic structure with capsule-like morphology of various length and diameters in the order of 20–70 nm and 10–30 nm, respectively. Capacitive performance of NiO nanocapsules were evaluated by cyclic voltammetry and galvanostatic charge/discharge measurements in a potential window between −0.2 and +0.5 V vs. Ag/AgCl. Electrochemical measurements revealed that the NiO nanocapsules have a specific faradaic pseudocapacitance as high as 307.2 F g−1 in 1 M KOH solution and good cycle life (approximately displayed 86.4% of its maximum capacitance after 3000 cycle discharging). These results showed that the prepared NiO nanostructure can be recognized as a promising candidate for the supercapacitor applications.
E139
Dingding Tang, Wei Xiao, Huayi Yin, Longfei Tian and Dihua Wang
Direct electrochemical reduction of solid CaWO4 to fine W powder in molten CaCl2-NaCl was studied by cyclic voltammetric measurement and potentiostatic/constant-voltage electrolysis. The effect of electrolysis conditions such as electrolysis time, temperature and voltage on the quality of the product (the residual amount of CaWO4) was systematically investigated. Based on the solubility tests of CaWO4 in the melt in a wide temperature range, an unprecedented strategy on electrolytic extraction of pure tungsten powder was proposed and confirmed, which involves low-temperature and short-duration electrolysis of solid CaWO4 in molten CaCl2-NaCl eutectic salt (1023 K, 10-hour electrolysis) followed by a simple washing process in the same melt at a higher temperature (1123 K, 1-hour washing). The particle size of the as-prepared W powder is less than 200 nm. This process exhibits a high yield and increased energy efficiency for production of fine W powder from CaWO4.
Physical and Analytical Electrochemistry
F141
James R. Jennings and Qing Wang
Errors in impedance measurements made on dye-sensitized solar cells (DSCs) and in subsequent model-based parameter extraction have been analyzed. The variance in the impedance was determined from replicate measurements using a “measurement model” approach. Measurement models were also used to identify corrupt data that were inconsistent with the Kramers-Kronig relations, providing justification for their rejection prior to further analysis. A common equivalent circuit model containing a transmission line was fitted to the refined data, which was weighted by the experimentally determined variance. For comparison, fits were also performed with the common “modulus” weighting strategy. Parameter confidence intervals were constructed from approximate standard errors and also from Monte-Carlo simulations based on the measured variance, which are presumably more accurate. Both weighting strategies yielded practically identical results for the main transmission line parameters, validating use of modulus weighting for routine work on DSCs. However, spectra could not be fitted to within the noise level, indicating that the model may need to be improved. Monte-Carlo confidence intervals were in all cases 10-20% tighter than those calculated from parameter standard errors for variance weighted fits and 3–15 times tighter than those for modulus weighted fits, implying the latter can be viewed as being pessimistic.
F150
Minzhi Wang and Jianbin Zheng
The direct electrochemistry of hemoglobin (Hb) immobilized on the designed carboxyl functionalized polystyrene/graphene-carbon nanotube-Nafion modified indium tin oxide (PS/GE-CNT-Nafion/ITO) electrode and its electrocatalysis for hydrogen peroxide (H2O2) were investigated. UV-visible and Fourier-transform infrared spectra of the resulting Hb-PS/GE-CNT-Nafion composite film suggested that the immobilized Hb retained its original structure. The direct electron transfer behaviors of Hb at the Hb-PS/GE-CNT-Nafion/ITO electrode were investigated by cyclic voltammetry in which a pair of well-defined, quasi-reversible redox peaks with the formal potential (E0′) of −0.249 V (vs. SCE) in phosphate buffer solution (0.05 M, pH 7.0) was obtained. The proposed ITO modified electrode exhibited an excellent electrocatalytic activity to the reduction of H2O2, and the peak currents were linearly related to H2O2 concentration in a wider linearity range from 5.0 × 10−7 to 1.4 × 10−3 M with a correlation coefficient of 0.9983 and a detection limit of 2.0 × 10−7 M (S/N = 3). The sensitivity and the apparent Michaelis-Menten constant (
) were determined to be 59.1 μA·mM−1 and 8.3 × 10−5 M, respectively. It is expected that the synergetic effects of GE-CNT hybrid materials and functionalized PS provide a general platform for studying of the electron transfer of redox proteins and the design of novel biosensors.
F157
Rahul Pal, S. Anthonysamy and V. Ganesan
Electrochemistry of deposition of boron on a platinum electrode from KCl (81.54 mol%)-KF (18.45 mol%)-KBF4 (1.6 to 7.73 × 10−4 mol cm−3) melts was studied by cyclic voltammetry, chronoamperometry and convolution voltammetry. These studies were carried out over the temperature range 1073–1123 K. Boron-containing complexes are shown to reduce quasireversibly (scan rate: <0.1 V s−1) and irreversibly (scan rate: >0.1 V s−1) through a single-step three-electron process (B(III) + 3e → B). The transfer and diffusion coefficients were measured at different KBF4 concentrations in the melt over the temperature range 1073–1123 K by using cyclic voltammetry, convolution voltammetry and chronoamperometry.
F166
Michael May, Elizabeth Paul and Vladimir Katovic
The electrolytic decomposition of 13C-enriched oxalic acid was investigated. Oxalic acid and oxalic acid-13C2 were pre-purified by vacuum sublimation and characterized by assay, melting range, and FTIR. An Integrated Vacuum Electrochemical Reactor (IVER) was employed to convert aqueous-phase oxalic acid to CO2 for the 13C-enrichment determinations: oxalic acid solvation, vacuum degas, electrolysis, and mass spectrometric analysis. Highly enriched oxalic acid-13C2 was electrolyzed at 1.5-VDC and the CO2 determined to be 99.5 atom%-13C. Blends of H2C2O4 and H213C2O4 were prepared from 50.5 to 99.5 atom%-13C, dissolved in water, and electrolyzed. For each blend solution, the [12C/13C] isotope separative effect was observed as increases in the (CO2) 13C-enrichment when the aqueous-phase was repeatedly electrolyzed. Furthermore, 50 atom%-13C oxalic acid was electrolyzed while the IVER current was monitored, and thereby the electrolytic isotope separation factor α[12C/13C] is estimated to be 1.03 ± 0.01, at 295 K on platinum. Cyclic voltammograms of 0.10-mole% oxalic acid in water displayed an irreversible oxidation peak at E = +0.95 volt (oxalic acid) and another oxidation peak at E ≥+1.6 volt (water). Cyclic voltammograms of oxalic acid in EMI+BETI− indicate that H2C2O4 can also be oxidized in liquid salts (voltammetric window ∼ 1.4 volt versus Ag/AgCl).
F174
F. Varmaghani, D. Nematollahi and S. Mallakpour
Cyclic voltammetry results as a diagnostic technique for electrochemical oxidation of 4-(4-R-phenyl)-1,2,4-triazolidine-3,5-diones (1-5) are reported and discussed. The results indicate that the electrochemically generated 4-(4-R-phenyl)-4H-1,2,4-triazole-3,5-diones (1ox-5ox) are unstable and participate in oxidative ring cleavage. In this study, the effect of different parameters such as pH, 4-phenylurazole concentration, solvent, temperature, substitute effect and time window of chosen electrochemical method have been studied. Also, the transfer coefficient, α, exchange current density, J0, the formal potential, E0’ and diffusion coefficient, D, of 4-phenylurazole (1) have been calculated. In addition, the observed homogeneous rate constants of oxidative ring cleavage of 4-phenylurazole derivatives were estimated by comparing the experimental cyclic voltammetric responses with digital simulated results.
Dielectric Science and Materials
G75
D. Dewulf, A. Hardy, S. Van Elshocht, C. De Dobbelaere, W. C. Wang, M. Badylevich, V. V. Afanas'ev, S. De Gendt and M. K. Van Bael
In this work, compositional series of Gd-Nb-oxides and Gd-Ta-oxides are investigated as new potential high-k materials. Ultrathin oxide films in the range of 5–25 nm are deposited by spincoating. XRD and AFM show that the films are amorphous and smooth (RMS < 1 nm). Dielectric constants are derived from capacitance voltage (CV) measurements and EOT extraction. K values of the Gd-Nb-Ox series range from 13–16 while higher k values are obtained for the Gd-Ta-Ox series ranging from 15–19. For the Gd-Nb-Ox series, a higher k value is obtained for the most Gd-rich composition, while the opposite trend for the Gd-Ta-Ox series is noticed. Furthermore, the Gd-Ta-Ox shows the lowest leakages, as concluded from current-voltage (IV) measurements. A higher Gd content leads to decreased leakage, concurrent with increased band gaps.
G80
S. Consiglio, R. D. Clark, E. Bersch, J. D. LaRose, I. Wells, K. Tapily, G. J. Leusink and A. C. Diebold
In this work, we present structural characterization of HfO2 films deposited using a cyclical deposition and annealing scheme (termed DADA). Electrical performance improvements were obtained for atomic layer deposited (ALD) HfO2 films grown by use of this DADA process compared to a single deposition followed by a post-deposition anneal (PDA). In order to probe the structural characteristics of films deposited using this DADA process, in this study we utilized grazing incidence in-plane X-ray diffraction and pole figure measurements using synchrotron radiation as well as transmission electron microscopy. Structural differences were investigated from different annealing conditions as well as from different thickness of films. We observed significant differences in structural properties of DADA films compared to films receiving PDA. We also report on the evolution of monoclinic HfO2 with a (
11) preferred orientation (fiber texture) for DADA films whereas PDA treatment resulted in a random grain alignment and mixed phase structure.
G89
Jeong Hun Mun, Sung Kyu Lim and Byung Jin Cho
Carbon ions were implanted in a nickel thin film. After subsequent rapid thermal annealing, they segregated on the surface, forming a graphene layer. The dependence of graphene synthesis on process conditions, including the carbon implantation dose, RTA temperature, and time, were investigated. The graphene shows quality comparable to that of the best reported CVD graphene. It was also found that local growth of graphene through local implantation requires stringent control of the process chamber conditions in order to avoid growth of graphene on unimplanted regions.
Semiconductor Devices, Materials, and Processing
H555
Silvia Baldovino, Alessio Lamperti, Marco Fanciulli and Alessandro Molle
The electrical quality of the GeO2/Ge interface, prior to and after Gd2O3 deposition, has been investigated as a function of the oxidizer (atomic O, O2, O3) used for the GeO2 based passivation of the Ge surface. In particular, the density of interface traps depends on the details of the Ge oxidation process and on the reactivity of the GeO2 passivation layer with the overlying Gd2O3 film. Complementary compositional depth profiling analysis shows that the oxygen content in the interfacial layer varies as a function of the type of oxidizer and plays a key role in dictating the interface chemistry and the electrical features of the MOS structures.
H560
Ja-Yong Kim, Deok-Sin Kil, Jin-Hyock Kim, Se-Hun Kwon, Ji-Hoon Ahn, Jae-Sung Roh and Sung-Ki Park
Ru films were produced by atomic layer deposition (ALD) with an alternating supply of bis(ethylcyclopentadienyl)ruthenium (Ru(EtCp)2) and ozone at deposition temperatures of 225–275°C. Ozone acted as an effective reactant for Ru(EtCp)2. The Ru film thicknesses formed during one cycle were saturated at relatively high values of 0.09–0.12 nm/cycle depending on the deposition temperatures, and their resistivities were about 16 μΩ cm. Moreover, a reduced nucleation delay was found for Ru ALD using ozone when compared to Ru ALD using oxygen gas. The amount of oxygen impurity incorporated into the Ru films was less than 1 at%, as determined by Auger electron spectroscopy. The interfacial adhesion property between Ru films prepared via ALD using ozone (ozone-Ru) and ZrO2 was good and 80% step coverage was achieved on a 3-D structure with a very high aspect ratio of 16:1, making them suitable for use as a top electrode material.
H565
Feng Jiang, Honglie Shen, Jiale Jin and Wei Wang
The Cu2ZnSnS4 (CZTS) film was successfully prepared and the Raman peaks at 251, 288, 335 and 368 cm−1 were observed. The light absorption coefficient of CZTS film is higher than 104 cm−1 and the energy bandgap is estimated to be about 1.5 eV. The photo-current response under different electrical field was studied for CZTS film. Persistent photoconductivity effect was observed and the decay time of current was studied under different electrical fields. The decay time of current decreased from 218 s to 0.2646 s with the electrical field reducing from 1 V to 1 × 10−4 V, respectively.
H570
P. G. D. Agopian, J. A. Martino, E. Simoen and C. Claeys
In this work, the impact of global and/or local strain engineering techniques on tri-gate p- and nMuGFETs performance is experimentally evaluated. Multiple gate structures were analyzed through basic and analog performance parameters for four different splits processed with different strain-engineering techniques (unstrained, uniaxial, biaxial and uniaxial+biaxial stress). While n-channel devices with narrow fins present a worse analog behavior, biaxial stress promotes the electron mobility for larger devices increasing the voltage gain. Besides the voltage gain, the transconductance, output conductance and Early Voltage are also evaluated. Although pMuGFETs are less affected by the strain engineering, they present better analog behavior for all studied devices.
H575
Dong-Jin Yun and Shi-Woo Rhee
The Oxygen (O2) annealing processes of metal electrode in rapid thermal annealing (RTA) and furnace were applied to modify surface properties including work function and bonding state without change in bulk properties. The Mo/Ti (50/3 nm) and Cu/Ti (50/3 nm) films were annealed at different temperature in RTA and furnace, and the film properties of them were characterized with various analytical tools to optimize annealing condition. At high annealing temperature, both Mo/Ti and Cu/Ti films were fully oxidized and bulk properties of them such as resistivity, crystallinity and morphology also changed. But the metal electrode annealed at specific annealing temperature showed distinctive behavior that the binding energy and work function only changed without change in bulk properties. During annealing process, the oxidation reaction is gradually proceed when the oxygen gas of sufficient energy contact metal atom at surface region and diffuses from surface region to bulk region of metal film. For one example, the work function of Mo/Ti film annealed at 300°C in RTA increased from ∼4.6 eV to ∼5.2 eV, but the bulk properties such as sheet resistance (∼31.6 Ω/□), roughness (0.951 nm) and crystallinity were maintained to similar characteristics with those of as-deposited Mo/Ti film.
H582
B. C. Peethala, H. P. Amanapu, U. R. K. Lagudu and S. V. Babu
A colloidal silica-based slurry with H2O2 (1 wt%) as the oxidizer and arginine (0.5 wt%) as the complexing agent was found to polish cobalt (Co) with superior performance (better post-polish surface quality and no pit formation) at pH 10 compared to pH 6 and 8. At pH 10, there is no measurable dissolution of Co and an open circuit potential (Eoc) difference of ∼20 mV between Cu and Co, suggestive of reduced galvanic corrosion. Our results also suggest that, during polishing, the Co film surface was covered with a passive film, possibly of Co(III) oxides. Addition of 5 mM BTA to this slurry inhibited Cu dissolution rates and yielded a Co/Cu removal rate ratio of ∼1.2 while further reducing the Eoc difference between Cu and Co to ∼10 mV, both very desirable attributes. The roles of H2O2, arginine, and silica abrasives as well as the pH on the Co material removal process are discussed and a removal mechanism is proposed.
H589
Somnath Mondal, Jim-Long Her, Shao-Ju Shih and Tung-Ming Pan
The structural and electrical properties of Lu2O3 dielectric films deposited by radio frequency (RF) magnetron sputtering on TaN electrode have been studied for metal–insulator–metal (MIM) capacitor in analog/RF applications. From X-ray diffraction study, it is observed that the deposited films remain amorphous within the thermal budget (400°C) of back-end-of-line process. The root mean square value of surface roughness of the Lu2O3 film decreases after annealing at 400°C using atomic force microscopy. The chemical composition of the Lu2O3 film was characterized by X-ray photoelectron spectroscopy. The MIM capacitor using a Lu2O3 dielectric film exhibited better electrical characteristics, such as a low leakage current of 5 × 10−8 A/cm2 at −1 V and a high capacitance density of 7.5 fF/μm2 with a low quadratic voltage coefficient of capacitance of 75 ppm/V2. The current conduction mechanism was found to be dominated by Schottky emission mechanism in low electric field (<1 MV/cm) region and hence further improvement in the leakage characteristics can be realized by employing a high work-function electrode or a large bandgap oxide as a barrier layer.
H595
Adam Birge and Yue Kuo
Memory functions of MOS capacitors with the nanocrystalline ITO embedded zirconium-doped hafnium oxide high-k gate dielectric thin film and the ITO gate electrode have been studied. Compared with the capacitor of the same dielectric stack but an aluminum gate, the ITO gated sample has a larger charge storing density. The primary memory mechanism of this device is based on hole injection and trapping to the embedded nanocrystalline ITO layer supplied from the substrate under a negative gate bias condition. The large work function of the ITO gate makes it difficult to transfer electrons from the gate to the embedded nanocrystalline ITO site, which favors the hole storage. Under the positive gate bias condition, all positive charges stored in the ITO gated capacitor are erased while those stored in the aluminum gated capacitor are partially erased.
H599
Y. C. Lin, T. Y. Chen, L. C. Wang and S. Y. Lien
This study prepared aluminum and gallium co-doped zinc oxide (AGZO) thin films using pulsed direct current magnetron sputtering, and studied the electrical properties, transmittance, effects of texturing, and applicability as the front contact for a-Si:H solar cells. Textured ZnO:Al (AZO) and ZnO:Ga (GZO) thin films were also compared with AGZO thin film to evaluate their performance as front contacts. Experimental results show that AGZO films with the highest figure of merit ϕTC value (24.64 × 10−3 Ω−1) were obtained at Al and Ga doping concentrations of 0.54 wt% and 1.165 wt%, respectively. The textured AGZO films used as the front contact in a-Si:H solar cells achieved the following results: VOC = 0.77 V, JSC = 16.5 mA/cm2, FF = 59%, and conversion efficiency of 7.53%. AZO and GZO films have better electrical properties than AGZO film; however, AGZO film has superior transmittance in the near-infrared (NIR) region and higher JSC, conversion efficiency and external quantum efficiency (EQE) than AZO and GZO films under a similar haze value.
H605
C. W. Chang, M. H. Hon and I. C. Leu
We use a simple and all-aqueous method, transfer printing, to pattern solution-processed graphene oxide (GO). We took advantage of the naturally charged property of GO, which were prepared using the Hummers’ method, to pattern it on the Si/SiO2 substrates which were pre-soaked in polyethyleneimine (PEI) solution. The charged GO was spin-coated on the polydimethylsiloxane (PDMS) stamp to achieve maskless patterning by a transfer printing method. The feature sizes of the printed GO patterns obtained range from 20 to 90 μm and the transfer-printed area reaches 2 cm* 2 cm. We also discuss the mechanisms of the transfer process, which are dependent on the different strengths of nonspecific adhesion at the interface between the PDMS-GO sheets and substrate-GO sheets, as well as the electrostatic interaction between charged functional groups on GO and PEI molecules. Raman spectra and mapping not only show the result of area-selective patterning, but also show the continuity of the GO patterns. Finally, we use this method to fabricate GO patterns on glass substrate and transform these GO patterns to reduced graphene oxide through thermal treatment.
Sensors and Displays: Principles, Materials, and Processing
J205
Sung-Gi Hur, Hyung-Jin Choi, Soon-Gil Yoon and Geun-Hong Kim
Photo-response switching of the CdS films grown at an optimum condition for the photo-sensor applications was investigated by an application of the electrical field. Recovery to the original dark-resistance after a light-off was achieved for 60 s by an application of the electrical field (∼30 V) in the two electrodes structure. On the other hand, in the structure of three electrodes, after application of −10 V for microsecond at third electrode at a light-off state, the dark-resistance was recovered to its original value for three second. An application of the negative electrical field in the three electrodes structure remarkably improved the switching characteristics of the photo-response of the CdS films.
J209
Y. Z. Yoo, J. S. Choi, K. J. Kim, G. J. Woo and B. M. Park
The influence of auto-doped oxygen on the activation efficiency of the Si dopant in GaN is directly observed. The activation efficiency of the Si dopant showed a drastic decrease, from 55% to 30%, in response to a slightly increased oxygen concentration. This decrease revealed that auto-doped oxygen (∼1016/cm3) in GaN played a crucial role in the activation efficiency of the Si. The detailed compositional, electrical characterization, and photoluminescence results illuminated the oxygen dependence of the electrical properties of Si-doped Hydride Vapor Phase Epitaxy GaN.
J212
Mikhail G. Brik and Alok M. Srivastava
The structural, electronic, optical and elastic properties of the potassium hexafluorosilicate (K2SiF6) lattice have been evaluated by the Density Functional Theory (DFT)-based ab initio calculating techniques. The first estimations of the bandgap, elastic constants, and Debye temperature are reported. Further, the dependence of these properties of the K2SiF6 lattice on pressure is evaluated and discussed.
J217
Éder José Guidelli, Elidia Maria Guerra and Marcelo Mulato
Vanadium/titanium mixed oxide films were produced using the sol-gel route. The structural investigation revealed that increased TiO2 molar ratio in the mixed oxide disturbs the V2O5 crystalline structure and makes it amorphous. This blocks the TiO2 phase transformation, so TiO2 stabilizes in the anatase phase. In addition the surface of the sample always presents larger amounts of TiO2 than expected, revealing a concentration gradient along the growth direction. For increased TiO2 molar ratios the roughness of the surface is reduced. Ion sensors were fabricated using the extended gate field effect transistor configuration. The obtained sensitivities varied in the range of 58 mV/pH down to 15 mV/pH according to the composition and morphology of the surface of the samples. Low TiO2 amounts presented better sensing properties that might be related to the cracked and inhomogeneous surfaces. Rising the TiO2 quantity in the films produces homogeneous surfaces but diminishes their sensitivities. Thus, the present paper reveals that the compositional and structural aspects change the surface morphology and electrical properties accounting for the final ion sensing properties of the V2O5/TiO2 films.
J223
Hai Guo, Xue Yun Liu, Fang Li, RongFei Wei, YunLe Wei and ChongGeng Ma
Eu3+ and Eu2+ co-doped aluminosilicate glass and glass ceramics containing BaAl2Si2O8 were prepared by melt-quenching technique in air and their luminescent properties were investigated by excitation, emission spectra and lifetime measurement. Intensities of Eu3+ and Eu2+ emissions in glass ceramics were enhanced by about 9 and 20 times compared to that in precursor glass, respectively. More interesting, under 380 nm excitation, a perfect white light with chromaticity coordinates (X = 0.333, Y = 0.307) was achieved for glass ceramics by combining intense red emission of Eu3+ with broad blue-green emission of Eu2+. Our results indicate that mixed-valence Eu-doped BaAl2Si2O8 glass ceramics may be used as potential phosphors for W-LEDs.
J227
Hyun Kyoung Yang, Byung Kee Moon, Byung Chun Choi, Jung Hyun Jeong and Kwang Ho Kim
YVO4 micro-rods were synthesized using a high-energy ball milling (HEB) method without other chemicals or solvents. The powder samples were sintered in air at 350, 400, 450, 500, 550 and 600°C for 5 h to form the polycrystalline YVO4 micro-rods. The effects of the processing parameters on the crystallinity, morphology and structure were examined by X-ray diffraction, field emission-scanning electron microscopy and TEM. The rate of YVO4 rod formation from NaYV2O7 increased with increasing sintering temperature. The luminescent properties were determined from their excitation and emission spectra. Overall, high-energy ball milling (HEB) is a promising method for preparing YVO4 with a rod-like morphology.
J231
Huimin Zhao, Yaqiong Chen, Junping Tian, Hongtao Yu and Xie Quan
A novel electrochemical sensor for the detection of chloramphenicol (CAP) was developed by modifying carboxyl acid functionalized multiwall carbon nanotubes (c-MWNTs) doped with gold nanoparticles (AuNPs) with a molecularly imprinted polymer (MIP) film on the surface of a glassy carbon electrode (MIP/c-MWNTs-AuNPs/GCE). The resulting electrode exhibited good performance for CAP detection based on the recognition capability of the imprinted film, as well as the specific surface area and electron transfer ability of c-MWNTs doped with AuNPs. A linear response to a concentration range of 0.1–100 mg L−1 (r2 = 0.9962) and a detection limit (with a signal to noise ratio of 3) of 0.024 mg L−1 CAP were achieved under optimized conditions. When penicillin-G (Pen-G), thiamphenicol (TAM) and p-nitrophenol (p-NP) were used as the interferents, the MIP/c-MWNTs-AuNPs/GCE sensor showed good selectivity and interference immunity, and the signal responses of Pen-G and TAM were 0.11% and 5.8% that of the response for CAP, respectively. The MIP/c-MWNTs-AuNPs/GCE electrode showed a pronounced electrochemical response to CAP, and as such constitutes a promising strategy for the electrochemical detection of CAP.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K161
Kuan Zhong, Yanchao Mao, Xiaofeng Sun, Chaolun Liang, Peng Liu and Yexiang Tong
The electrochemical and optical properties of ZnO nanowires modified with Ag nanoparticles by electrodeposition are studied. The results of cyclic voltammetry and chronoamperometry show that the radiated, well-crystallized ZnO-nanowire electrode, with a spacial architecture, allows fast Ag(I) ion diffusion, rapid electron transfer, and high Ag deposition rate. Numerous Ag nanoparticles deposited on the nanowires induce a redshift of 0.23 eV in the ZnO optical bandgap while without causing a large decrease in optical absorption intensity. However, a great decrease in photoluminescence intensity occurs in the modified structure, mainly resulting from the charge transfer between ZnO and Ag. The composite structure has promising applications in photocatalysis and photovoltaics.
K165
M. K. Debe, S. M. Hendricks, G. D. Vernstrom, M. Meyers, M. Brostrom, M. Stephens, Q. Chan, J. Willey, M. Hamden, C. K. Mittelsteadt et al
Water based electrolyzers offer a promising approach for generating hydrogen gas for renewable energy storage. 3M's nanostructured thin film (NSTF) catalyst technology platform has been shown to significantly reduce many of the performance, cost and durability barriers standing in the way of H2/air PEM fuel cells for vehicles. In this paper we describe results from the first evaluations of low loaded NSTF catalysts in H2/O2 electrolyzers at Proton OnSite and Giner, Inc. Over two dozen membrane electrode assemblies comprising nine different NSTF catalyst types were tested in 11 short stack durability tests at Proton OnSite and 14 performance tests in 50 cm2 single cells at Giner Electrochemical Systems. NSTF catalyst alloys of Pt68Co29Mn3, Pt50Ir50 and Pt50Ir25Ru25, with Pt loadings in the range of 0.1 to 0.2 mg/cm2, were investigated for beginning-of-life performance and durability up to 4000 hours as both electrolyzer cathodes and anodes. Catalyst composition, deposition and process conditions were found to be important for meeting the performance of standard PGM blacks on electrolyzer anodes while using only 10% as much PGM catalyst. Analyses of MEA's after the durability tests by multiple techniques document changes in catalyst alloy composition, loading, crystallite structure and support stability.
K177
Zhongrui Wang, V. Tjoa, L. Wu, W. J. Liu, Z. Fang, X. A. Tran, J. Wei, W. G. Zhu and H. Y. Yu
Resistive switching in Graphene Oxide (GO) based RRAM has been studied in combination with various commonly used electrodes e.g. Al, Cu, Ni and Ti. For the first time, coexistence of different reproducible switching directions has been observed in the Al/GO/Pt and the Ti/GO/Pt RRAM cells. These switching directions are correlated to the underlying switching mechanisms as revealed by field dependence, temperature dependence and area dependence. Our observation also suggests that both oxygen related functional groups absorption/release and electrode metal ions diffusion play important roles in bipolar resistive switching of GO.
Interdisciplinary Topics
P51
Ding-Shiang Wang, Shou-Yi Chang, Yi-Chung Huang, Jin-Bao Wu, Hong-Jen Lai and Ming-Sheng Leu
In this study, very simple periodic cathodic vacuum arc deposition was conducted to prepare multilayered structures of diamond-like carbon films with reduced surface roughness and enhanced mechanical properties compared to conventional unfiltered single-layered films. The roughness of single-layered diamond-like carbon films significantly increased from 23 to 104 nm with increasing thickness from 100 to 800 nm due to the droplet formation in plasma atmosphere. By introducing periodic deposition, the roughness of the multilayered structures with a thickness of 400 nm was reduced from 75 to 37 nm, associated with a much smaller number of surface particles. The hardness of the multilayered structures was enhanced from 27 to 34 GPa, and the interface adhesion was increased from 2.73 to 3.63 J/m2. The single- and multilayered films showed a similar amorphous structure with slightly varied ID/IG ratios from 0.9 to 0.6. The periodic deposition process was the dominant factor for the reduced roughness and enhanced mechanical properties of the unfiltered films.
P57
D. Ippolito, K. B. Andersen and K. K. Hansen
The propene catalytic oxidation was studied over an 11-layers porous electrochemical reactor made by La0.85Sr0.15MnO3 and Ce0.9Gd0.1O1.95 with the objective to simulate the abatement of exhaust gases emitted from Diesel engines. This work shows the possibility to enhance the catalytic activity through infiltration of Ce0.9Gd0.1O1.95 using the porous electrochemical reactor as a catalyst support. The infiltration of an oxygen ion conductor as Ce0.9Gd0.1O1.95 showed an increased activity either at open circuit voltage (OCV) or under polarization with respect to the non infiltrated cell. The use of infiltration permitted to maintain high the effect of polarization also at low temperatures. The electrode was found to be strongly affected by morphology of infiltrated material and long term polarization brought about to an increase of catalytic activity. Moreover the phenomenon of electrochemical promotion of catalysis (EPOC) was found at low temperature.
Miscellaneous
S17
The following article is Free article
R. D. Long, B. Shin, S. Monaghan, K. Cherkaoui, J. Cagnon, S. Stemmer, P. C. McIntyre and P. K. Hurley