Batteries and Energy Storage
A1
Yang-Kook Sun, Hyung-Joo Noh and Chong S. Yoon
Two novel core-shell cathode materials with average compositions of Li[Ni0.82Co0.04Mn0.14]O2 and Li[Ni0.81Co0.06Mn0.13]O2 were synthesized via coprecipitation. Each core-shell material had a common Li[Ni0.9Co0.05Mn0.05]O2 core which was completely encapsulated by two different concentration-gradient shells with stable surface compositions of Li[Ni0.67Co0.01Mn0.32]O2 and Li[Ni0.62Co0.14Mn0.24]O2. Electrochemical and thermal properties of the two materials were investigated and compared to those of the core Li[Ni0.9Co0.05Mn0.05]O2 material. The Li[Ni0.82Co0.04Mn0.14]O2 with a high concentration of Mn in the surface layer exhibited improved cycling performance and structural and thermal stability compared to Li[Ni0.81Co0.06Mn0.13]O2 as well as the core material without the concentration gradient shell. Electrochemical impedance spectroscopy and electron microscopy showed that Mn concentration in surface layer played an important role in stabilizing the surface structure and thus suppressing the increase in the interfacial resistance between the cathode and the electrolyte.
A6
Bal Sydulu Singu, Palaniappan Srinivasan and Srinivas Pabba
Benzoyl peroxide is used as an oxidant for the oxidation of aniline to polyaniline salt via interfacial polymerization pathway (IP) for the first time in presence of sodium lauryl sulfate as emulsifier and 5-sulfophthalic acid as protonic acid. Polyaniline salt is also synthesized by interfacial polymerization using higher amount of reactants and emulsion polymerization pathways. Polyaniline salts are characterized by FT-IR, XRD and SEM. This polymerization process gives polyaniline salt containing dual dopants (5-sulfophthalic acid and dodecyl hydrogen sulfate) i.e. small and long chain molecules on polyaniline. Polyaniline salt prepared by emulsion polymerization pathway (EP) shows nanowires with a higher yield (0.98 g) compared to that of the interfacial polymerization (IP) pathway (0.73 g), which also shows nanowires morphology. However, very less yield (0.2 g) is obtained by the interfacial polymerization pathway using higher concentration of reactants (IP-H), which shows nanotubes. Polyaniline salt is mixed with Multi-walled carbon nanotube (MWCNTs) material, made electrode with stainless steel mesh and this electrode is used for the study of symmetric supercapacitor cell. Electrochemical performance is found by cyclic voltammetry, charge-discharge and electrochemical impedance spectroscopy. The results clearly indicate that the polyaniline salt containing dual dopants is a very good material for supercapacitor.
A14
Tetsu Ichitsubo, Shunsuke Yagi, Takayuki Doi, Shunsuke Yukitani, Kosuke Hirai and Eiichiro Matsubara
While an Al-Li alloy is expected to be useful as an active material for a negative electrode in a Li battery, the electrochemical lithiation of pure Al metal is known to be quite difficult. In this work, we sought to clarify why an Al electrode hardly absorbs Li from a pure Al state, from the viewpoint of elasticity theory and thermodynamics. We consider two cases: (i) an AlLi compound with elastic strain due to volume expansion is formed in the Al matrix, and (ii) Li ions are absorbed into an Al electrode that has been pre-strained by rolling. These strain-energy effects are discussed with the aid of a chemical-potential diagram and the Gibbs-Duhem equation.
A18
N. Kircheva, S. Genies, D. Brun-Buisson and P.-X. Thivel
This paper has the aim to demonstrate that Acoustic Emission (AE) is an appropriate technique to become a diagnostic tool for state of charge, state of health and state of security of lithium-ion cells. These issues are actually key parameters for both performance and durability improvement. The presented results deal with the monitoring of the SEI formation and the first lithium ion intercalation on the surface and inside the graphite electrode. AE events coming from different sources have thus been identified. A large number of acoustic emission events occur during the film formation corresponding to gas evolution and cracking processes happening at the electrode surface (lithium intercalation). The acoustic emission signals were analyzed and correlated with electrochemical phenomena taking place during the cell operation.
A26
Kamakshi Jagannathan and K. Raghunathan
Lithium based batteries are of current interest for high rate applications in electric vehicles. Some of the electrode materials exhibit phase change characteristics upon lithium intercalation (or de-intercalation). The diffusion phenomenon in these electrode materials coupled with the phase change characteristics can lead to the existence of an asymmetric behavior between charge and discharge, which can be exhibited in the form of a higher cell capacity during charge when compared to discharge (or vice versa) at the same current density. In this work, the isotropic shell-core model is used to describe the diffusion phenomenon coupled with phase change, and approximate solution methods are presented for phase change electrodes. Additionally, the effect of transport properties (diffusivity coefficients) and thermodynamic properties (equilibrium concentrations) of the two phases which can be particle size and temperature dependent, on the charge-discharge asymmetric behavior and battery performance is studied. The diffusion models also suggest that for phase change electrode materials, it is possible that lowering the particle size is desirable not only for the obvious advantages of higher current densities and capacities but also to achieve less asymmetry between discharge and charge. Similar advantages can be obtained when these batteries are operated at higher temperatures.
A38
Sumit K. Soni, Brian W. Sheldon, Xingcheng Xiao, Mark W. Verbrugge, Ahn Dongjoon, Haftbaradaran H. and Gao Huajian
In this study, we report in situ measurements of lithium diffusion induced stress in patterned amorphous Si negative electrodes. This configuration was used as a model system to understand how the gap between islands can accommodate the large volume expansion and stress generation that occurs during the lithiation of Si. The effect of pattern size was studied systematically with 7 μm, 17 μm and 40 μm square islands. Experimentally measured stresses were then compared to a continuum model that describes stress accommodation due to interfacial sliding or plastic deformation in the underlying current collector. These results indicate that engineering an appropriately sized Si island is an effective method for mitigating lithiation-induced stress and mechanical degradation in Si based electrodes.
A44
Mingjiong Zhou, Liwei Zhao, Shigeto Okada and Jun-ichi Yamaki
To study the mechanism of exothermic reactions of charged graphite in electrolyte with temperature ramping up, the thermal behavior of charged graphite in solvent or electrolytes was investigated by DSC. When the charged graphite was heated up in the EC + DMC solvent, the dominant exothermic peak was observed at around 160°C. Both the amount of solvent and the content of intercalated Li had direct effect on the thermal behavior of the peak at around 160°C, indicating that this peak should be caused by the reaction between intercalated Li and solvent. However, when the solvent was replaced with LiPF6/EC + DMC electrolytes, the exothermic peak at around 160°C became mild and the heat values were much smaller, due to SEI formation on the anode. On the other hand, the exothermic heat of the peak at around 160°C decreased significantly with the increase of LiPF6 concentration of electrolyte. This phenomenon was discussed by considering the exothermic heat of the reaction between intercalated Li and EC + DMC solvent. It is clear that LiPF6 is needed in EC + DMC to form SEI on the charged graphite.
A49
Morihiro Saito, Yosuke Murota, Mikihiro Takagi, Makoto Tajima, Takayuki Asao, Hidemi Inoue, Akimasa Tasaka and Minoru Inaba
To improve the reversible capacity of TiO2(B) negative electrode close to the theoretical one, some preparation and experimental conditions such as the precursor (Na2Ti3O7, K2Ti4O9 and Cs2Ti5O11), the co-solvent in ethylene carbonate-based electrolyte solutions, and homogeneity of the composite electrode were optimized. TiO2(B) powder samples were successfully prepared from K2Ti4O9 and Cs2Ti5O11 precursors, but not from Na2Ti3O7. The sample prepared from Cs2Ti5O11 gave a higher discharge capacity (185.5 mAh g−1) than that prepared from K2Ti4O9 (156.6 mAh g−1). The reversible capacity of TiO2(B) was significantly influenced by the kind of co-solvent in the electrolyte solutions. The presence of dimethyl carbonate (DMC) as a co-solvent drastically improved the capacity, and the highest discharge capacity of 235.3 mAh g−1 was obtained in 1 M LiPF6 dissolved EC+DMC (1:2 by volume). Furthermore, improvement of the homogeneity of the composite electrode by premixing the TiO2(B) and Ketjen Black conductor was effective to improve the discharge capacity. The optimized electrode gave an initial discharge capacity of 314.4 mAh g−1, which reached 93.9% of the theoretical capacity (335 mAh g−1). It also exhibited a good cycleability (287.9 mAh g−1 after 50 cycles) and a high rate capability (118.5 mAh g−1 at 10 C rate).
A55
Jongsoon Kim, Kyu-Young Park, Inchul Park, Jung-Keun Yoo, Dong-Hwa Seo, Sung-Wook Kim and Kisuk Kang
The effect of particle size on the phase stability of delithiated LixMnPO4 (x < 1) is elucidated using temperature-controlled in situ X-ray diffraction (XRD). The phase transformation of LixMnPO4 (x < 1) at high temperature was apparently altered by the particle size. While LixMnPO4 phase having large particle size (ca. 200 nm to 1 μm) decomposed into Mn2P2O7 at the temperature between 200°C and 250°C, consistent with previous studies, phase transformation into Mn3(PO4)2 was observed at the same temperature when the delithiated LixMnPO4 phase had a small particle size (ca. 50 nm). This indicates that the phase transformation of a LiMnPO4-based battery may vary with particle size.
A60
Claudine Hamel, Thierry Brousse, Daniel Bélanger and Daniel Guay
High energy ball-milling (HEBM) of pure PbO2 and of mixtures of PbO2 with BaSO4 was performed as a function of time. The powders were characterized by X-ray diffraction, scanning electron microscopy and X-ray photoelectron spectroscopy, while the intrinsic electrochemical properties of the powders were assessed in 1M H2SO4 using a cavity microelectrode (CME). During milling, there is a transition from a tetragonal structure (β-PbO2) to an orthorhombic structure (α-PbO2) and, after 1 h, the powder is composed of ∼80 wt% α-PbO2. The addition of BaSO4 doesn't influence the kinetics of the β- to ∝-PbO2 transition. Also, during milling, the crystallite size of β-PbO2 decreases from 25 to 8 nm, while the crystallite size of α-PbO2 is constant at 14 nm. During the first few hours of milling, there is a 50 mV shift of the potential corresponding to the maximum reduction and oxidation peak current towards less negative and positive values, respectively. This effect is emphasized by the addition of BaSO4, indicating that the reversibility of the PbSO4/PbO2 system is increased. This is thought to arise as a consequence of a reduction of the crystallite size and the presence of BaSO4.
Fuel Cells and Energy Conversion
B1
Dong Hyeop Shin, Young Min Shin, Ji Hye Kim, Byung Tae Ahn and Kyung Hoon Yoon
Orientation control of Cu(In,Ga)Se2 (CIGS) thin film could be critical to achieve conversion efficiency of CIGS solar cells that exceeds 20%. The preferred orientation of CIGS thin film is investigated here by modifying the surface of an underlying Mo film. The orientation and surface morphology of the Mo film were modified by varying the deposition pressure during the sputtering process. The Mo surface showed a (110)-preferred orientation at low deposition pressures and a (221)-preferred orientation at high deposition pressures. With a Se pretreatment at 400°C, a strong (002)-oriented MoSe2 layer was formed on the (110)-oriented Mo film and a randomly oriented MoSe2 layer was formed on the (221)-oriented Mo film. We found that a (112)-oriented CIGS film was grown on the (002)-oriented MoSe2 surface, while a (220)/(204)-oriented CIGS film was grown on the randomly oriented MoSe2 surface. The orientation of the MoSe2 layer that was dependent on the surface morphology of the Mo film played a role in determining the preferred orientation of the CIGS thin film. The sequential progress of the orientation development of Mo, MoSe2, (In,Ga)2Se3 and Cu(In,Ga)Se2 films in a three-stage co-evaporation process is examined and discussed.
B6
Jung-Min Kim and Shi-Woo Rhee
To study the effect of stainless steel (SS) surface morphology as a counter electrode and a flexible substrate in dye sensitized solar cells (DSCs), SS surface was treated with chemical mechanical polishing process or etched with hydrochloric acid for various times. Pt catalytic layer was deposited either with sputtering at room temperature or thermal decomposition of precursor solution (H2PtCl6). From the electrochemical impedance measurement on the symmetric cell, the charge transfer resistance at the electrolyte/counter electrode interface and the internal resistance were obtained. When Pt was deposited on polished SS with sputtering, fill factor (FF) and efficiency were decreased due to the decrease in surface area. On the other hand, the catalytic activity was improved with etching due to the increase in the surface area leading to the improvement in FF and efficiency (71.0% and 7.7%). When the Pt layer was formed with thermal decomposition on the SS substrate, FF and efficiency were significantly decreased with poor catalytic activity regardless of the surface area, due to the oxidation of the SS surface during the thermal decomposition process at high temperatures.
B12
Jose A. Vega, Sujan Shrestha, Michael Ignatowich and William E. Mustain
Synthesis of a carbonate selective Ca2Ru2O7-y catalyst was investigated using solid-state and hydrothermal routes. The resulting materials were physically characterized by x-ray diffraction, BET gas adsorption, scanning electron microscopy and temperature programmed desorption. The solid-state reaction of precursor oxides, CaO and RuO2, led to the formation of a perovskite phase. A hydrothermal route using O2 as an oxidizing agent yielded a mostly amorphous phase primarily comprised of unreacted precursor. The use of low concentration KMnO4 (10 mM) as a replacement for O2 in the hydrothermal synthesis, in combination with high pH (∼14) and moderate temperature (200°C), yielded a highly crystalline, thermally stable Ca2Ru2O7-y pyrochlore. The increase in crystallinity was attributed to the ability of permanganate to maintain ruthenium in the +5 oxidation state required for formation of the pyrochlore phase. Micron-sized primary particles with a high density of ∼ 50 nm surface nanocrystallites were obtained. The presence of the nanocrystallites gave the pyrochlore a high surface area, 174 m2/g. The pyrochlore showed preferential surface adsorption of CO2 compared to H2O, making it a feasible candidate for a carbonate selective catalyst. This preferential adsorption was attributed to the use of calcium, an alkaline earth metal, which gave the pyrochlore a high surface basicity.
B18
Jose A. Vega, Neil Spinner, Michael Catanese and William E. Mustain
The electrochemical selectivity of a Ca2Ru2O7−y pyrochlore catalyst towards carbonate formation was investigated and compared to platinum. During constant current operation, an increase in CO2 content was observed at the anode effluent when Ca2Ru2O7−y was used as the cathode catalyst, compared to Pt/C. Carbonate selectivity for Pt/C was 1.78, while for Ca2Ru2O7−y it was 7.33, a 4.1X increase, which confirmed the preferential formation of carbonate on the pyrochlore. This elevated selectivity was attributed to the high surface basicity of the pyrochlore catalyst, which led to preferential CO2 adsorption. During constant voltage operation, a 134% CO2 concentration increase was measured at the anode effluent when 10% CO2 was supplied to the cathode inlet. Optimal fuel cell performance on the carbonate cycle was obtained with a 90% O2/ 10% CO2 cathode concentration, where maximum currents where 4X compared to operation with no CO2. Higher CO2 concentrations were matched with a gradual decrease in performance. This was attributed to a relatively low electrochemical activity, which combined with high surface basicity, led to O2 site blocking. Thin-film electrode experiments showed excellent electrochemical stability on the oxygen reduction region. An increase in the current and a positive shift in the half-wave potential were observed when CO2 was added to the electrolyte in ex-situ three electrode experiments.
B24
Frédéric Hasché, Mehtap Oezaslan and Peter Strasser
We report a synthesis, activity and stability study of a dealloyed, highly active PtNi3 alloy nanoparticle catalyst for the oxygen reduction reaction (ORR) in acidic media. After activation by electrochemical dealloying of a PtNi3 precursor, the Pt-Ni nanoparticle catalyst (referred to as “dealloyed PtNi3”) exhibits a 7–8 times higher Pt mass based activity and a 6–7 times higher Pt surface area specific based activity for ORR than pure Pt at comparable mean particle size. In addition, the long-term stability of the dealloyed PtNi3 was tested for typical fuel cell operating as well as more corrosive fuel cell start-up conditions. After 10000 voltage cycles between 0.5–1.0 V vs. RHE at 50 mV s−1 the dealloyed PtNi3 catalyst still shows 4–5 fold increase in Pt surface area specific based activity compared with that for pure Pt.
B34
Yeonjun Oh, Ho Gyu Yoon, Sung-Nam Lee, Han-Ki Kim and Jihoon Kim
We have investigated the inkjet-printing of TiO2 films for the fabrication of dye-sensitized solar cells (DSSCs). In order to realize the uniform printing of TiO2 films, the co-solvent ink was designed by introducing a drying agent to the ink. This co-solvent ink induces a circulating flow within ink droplets and leads to the uniform lines and films by inkjet. A theoretical model was used to predict the optimal ink-droplet pitches for the inkjet-printing of uniform lines. This model also contributes to the formation of uniform films since they are filled with the inkjet-printed lines. The inkjet-printed TiO2 films were used as photoelectrodes for dye-sensitized solar cells. The thickness of the inkjet-printed TiO2 films was varied to optimize the photovoltaic performance of DSSCs. Since no organic additives were introduced into the TiO2 inks, the feasibility of reducing the annealing temperature for TiO2 photoelectrodes was investigated. This study may suggest an opportunity to fabricate DSSCs at low temperature.
B39
Anh T. Duong and Daniel R. Mumm
B53
Mark K. Debe
Commercialization of automotive fuel cells requires current densities of 1.5 A/cm2 above 650 mV with Pt loadings of 0.125 mgPt/cm2 or less. Loss of high current density with cathode loadings below 0.2 mgPt/cm2 in Pt/C electrodes is an issue that current kinetic/transport models are reported inadequate to explain. We show that this effect is much less at a given loading with the NSTF catalyst type electrodes and explain these differences using a model based on elementary kinetic gas theory and known molecule/surface interaction mechanisms that take place in the Knudsen regime. The result is an additional pre-exponential scaling factor f(ds) in the Butler-Volmer equation related to a distance metric ds describing the catalyst surface area distribution. We approximate this distance metric by the inverse of the surface area per unit volume of the electrode and define and test two possible functional forms for f(ds). The preferred form is able to predict the correct heat of enthalpy for O2 physisorption and the observed ratio of current densities at V(iR-free) = 0.7 V for NSTF compared to Pt/C dispersed electrodes in the 0.05 to 0.15 mgPt/cm2 range from published data for eleven different catalyst types and cathode loadings below 0.2 mg/cm2.
B67
Aligul Buyukaksoy, Vladimir Petrovsky and Fatih Dogan
A novel technique based on polymeric precursor infiltration into porous layers was developed to process composite materials as highly efficient cathode/current collector structures for solid oxide fuel cells (SOFCs). Powder based Pt and YSZ inks were used to form porous cathode/current collector layers on electrolyte supported symmetrical structures that were infiltrated with polymeric LSM precursor. Electrochemical testing of the samples was performed by impedance spectroscopy techniques. Polarization resistance of the cathode was as low as 0.022 Ohm.cm2 at 800°C demonstrating the potential of fabricating highly efficient cathodes. Infiltration process led to a stable composite of the cathode/current collector structures, ensuring a high current collection efficiency and long term stability at operational temperatures.
B72
C. Setevich, L. Mogni, A. Caneiro and F. Prado
The influence of temperature and procedure on the phase relationships of LaxBa1−xCoO3−δ with 0 ≤ x ≤ 1.0, oxygen nonstoichiometry, thermal and chemical expansion contributions, in air, and the electrochemical response of electrodes formed by three porous layers LaxBa1−xCoO3−δ/(50:50wt%)LaxBa1−xCoO3−δ+Ce0.9Gd0.1O1.95/Ce0.9Gd0.1O1.95 have been investigated. The crystal structures of samples with 0 ≤ x ≤ 0.5 and x = 1.0 were refined satisfactorily with a single phase. The cubic perovskite could be obtained for the x = 0.5−0.7 furnace-cooled samples (∼5°C/min). This phase was found unstable for x = 0.6 and 0.7, in air, at T ≤ 1000°C. For x = 0.8 and 0.9 a mixture of phases has been obtained. The expansion coefficient reaches a maximum of 26 × 10−6 K−1 for x = 0.6 and a minimum of 16 × 10−6 K−1 for x = 0.8 and 0.9 for ΔT = 20−900°C. AC impedance spectroscopy measurements were carried out in the temperature range of 400 ≤ T ≤ 700°C. A minimum polarization resistance Rp ∼ 0.065 – 0.075 Ω cm2 was obtained for 0.4 ≤ x ≤ 0.7 at T = 600°C, which compares very well with the Rp value reported for composites prepared with cobaltites.
B80
Mao-Sung Wu, Chen-Hsiu Tsai and Tzu-Chien Wei
Ultrathin anatase TiO2 films were coated on the fluorine-doped tin oxide (FTO) glass by anodic electrodeposition followed by annealing at 450°C before the formation of thick TiO2 layer. The electrodeposited TiO2 films were more compact structure near the FTO surface (inner layer), and became less compact further away from the surface (outer layer). The outer layer of film deposited at 10 μA cm−2 was composed of granular nanoparticles and that of film deposited at 5 μA cm−2 was composed of short nanorods. The inner compact layer could act as a blocking layer to suppress the charge recombination. The outer loose layer could provide an anchoring layer for a better electrical contact between FTO and thick TiO2 layer. The photoelectron conversion efficiency (η) of dye-sensitized solar cell (DSC) using TiO2-coated FTO deposited at 10 μA cm−2 was 6.9%, which is higher than that of DSC using bare FTO (6.5%). The outer anchoring layer composed of short nanorods deposited at 5 μA cm−2 could significantly reduce the interfacial contact resistance between FTO and main TiO2 layer. Therefore, η of DSC was further increased to 7.1% after employing the TiO2-coated FTO deposited at 5 μA cm−2.
B86
Ja-Yeon Choi, Drew Higgins and Zhongwei Chen
A novel NPMC using pyrimidine-2,4,5,6-tetramine sulfuric acid hydrate (PTAm) as a nitrogen precursor and graphene nanosheets as catalyst supports was prepared and characterized. We investigate the effect of different pyrolysis temperatures on the catalysts’ ORR activity along with detailed surface analysis to provide insight regarding the nature of the ORR active surface moieties. The NPMC sample heat treated at 800°C was found to display optimal ORR activity and H2O selectivity, specifically, an onset potential of 0.853 V vs RHE, a half-wave potential of 0.682 V vs RHE, and a H2O selectivity of ca. 99.9%. High stability through an accelerated durability testing (ADT) protocol was demonstrated and attributed to the high graphitic content of the catalyst support material. This novel NPMC demonstrates promising electrocatalyst activity and superior durability over commercial Pt/C catalyst for ORR under the studied conditions, rendering graphene nanosheets as an ideal replacement to traditional nanostructured carbon support materials.
Corrosion, Passivation, and Anodic Films
C1
H. Ashassi-Sorkhabi and E. Asghari
The hydrodynamic conditions and fluid flow are important factors that affect the corrosion of metals. They also influence the inhibition performance of different corrosion inhibitors. In this paper, the corrosion behavior of St52-3 rotating disc electrode, RDE, in NaCl solution containing ZnSO4 salt, as a cathodic inorganic corrosion inhibitor, has been studied under different hydrodynamic conditions. Two electrochemical methods, including potentiodynamic polarization and electrochemical impedance spectroscopy, have been used. The effects of solution hydrodynamic on the open circuit potential, polarization curves and electrochemical impedance diagrams of the steel RDE in blank NaCl solution as well as in the solution containing ZnSO4 have been considered. It has been shown that ZnSO4 inhibits the corrosion of steel in NaCl solution. By increasing the rotational speed, in the absence and presence of inhibitor, the corrosion current density increased and charge transfer resistance decreased. ZnSO4 had relatively low efficiency in stagnant conditions but its influence improved significantly under hydrodynamic conditions. It was mainly attributed to an increase in Zn2+ ions mass transport towards electrode surface, which leads to the formation of more protective films and therefore, enhances the protection against corrosion.
C8
Berny Rivera Vásquez, Gonzalo Viramontes Gamboa and David G. Dixon
Most of the electrochemistry of chalcopyrite reported in the literature has been done using either massive samples of the mineral or carbon paste electrodes. Despite its importance, reports of the electrochemical behavior of this mineral carried on individual microparticles are scarce. In this work the microelectrochemistry of chalcopyrite is studied in sulfuric acid solutions, focusing the study on its behavior at transpassive potentials. It is shown that microparticles with sizes typically found in chalcopyrite concentrates (20 to 100 μm) can be leached to completion in less than 4 minutes at room conditions under the influence of 1.2 V (SCE). According to EDX analysis, atomic absorption spectroscopy and ICP, around 88% of the sulfur in the mineral is transformed into a compact layer of amorphous plastic sulfur, while the rest is transformed to sulphate. The plastic sulfur gradually equilibrates to more stable S8-rings orthorhombic phase. This nearly instantaneous dissolution of chalcopyrite opens the window to the development of new technologies.
C15
S. A. Policastro, R. C. Y. Auyeung, F. J. Martin, R. J. Rayne, A. Piqué, A. Lewis, A. Geltmacher and P. M. Natishan
A novel experimental technique for making electrochemical measurements on individual phase or isolated regions of a metal or alloy is reported. The technique, called Selective Masking by Photolithography (SMP), uses a hardened photoresist coating to mask the excluded portions of the sample and 355 nm laser pulses are employed to expose individual grains or regions of interest. The size of the exposed area can range from tens of microns to millimeters. Localized electrochemical DC and AC measurements and critical pitting temperature determinations for the two phases in a duplex stainless steel were used to show the utility and viability of SMP.
C25
Qin Xu, Yu-Hua Yang, Li-Hu Liu, Jian-Jun Gu, Jing-Jin Liu, Zi-Yue Li and Hui-Yuan Sun
Highly ordered porous anodic alumina thin films with tunable structural colors covering the entire visible region have been fabricated using chemical etching. The relationship of the structural color to the anodization time and etching time in a phosphoric acid solution, as well as the angle of incidence of illuminating light are discussed. Multicolor patterns were obtained by an organics-assisted process. A theoretical study of the changes in structural color due to various factors is consistent with the experimental results. These films show promise in many areas including decoration, display and anti-counterfeiting applications.
C29
Heidi Conrad, John Corbett and Teresa D. Golden
Zinc-nickel alloys (γ-phase) with 8–15% nickel were electrochemically deposited onto stainless steel for increased corrosion protection. Alkaline deposition conditions were studied using ammonium hydroxide as the base source and a working pH range between 9.0–9.5. Sodium acetate was used as a complexing ligand and found to stabilize the metal ions in the electrolytic solution. Strongly adhering, quality deposits were obtained with room temperature electrodeposition. Uniform grain size and smooth deposits were observed with scanning electron microscopy, which lead to increased corrosion protection. X-ray diffraction and atomic absorption spectroscopy confirmed the deposits were γ-phase zinc-nickel with nickel content of 8–15% within the alloy. The corrosion potential for the γ-phase coatings was improved over that of pure zinc coatings by about 200 mV cathodic with respect to stainless steel but at a lower corrosion potential, thereby impeding the corrosion rate.
C33
F. Di Franco, G. Zampardi, M. Santamaria, F. Di Quarto and H. Habazaki
Tantalum oxide, niobium oxide and Ta-Nb containing mixed oxides were grown by anodizing sputter-deposited Ta, Nb and Ta-Nb alloys of different compositions. A photoelectrochemical investigation was performed in order to estimate the band gap and the flat band potential of the oxides as a function of their composition. The band gap of the investigated Ta-Nb containing mixed oxides changed monotonically between those estimated for Ta2O5 (4.1 eV) and Nb2O5 (3.4 eV) and in agreement with a proposed correlation between the Band gap of an oxide and the difference of electronegativity of the oxide constituents. From the differential capacitance curves recorded in a wide range of electrode potential and for several frequencies of the alternative signal, the dielectric constant of the investigated oxides were estimated.
C40
S. B. Brachetti-Sibaja, M. A. Domínguez-Crespo, A. M. Torres-Huerta, W. de la Cruz-Hernández and E. Onofre-Bustamante
Rare earth conversion films were obtained on the AA6061 aluminum alloy by the immersion method varying several experimental conditions such as rare earth (RE) concentration, bath temperature and immersion time. Formation dynamics of RE coatings and the effect of bath conditions on their structure, morphology, topography and corrosion resistance properties were investigated for the protection of this substrate immersed in an aqueous solution of NaCl. X-ray diffraction and scanning electron microscopy results revealed that the increment of the RE concentration caused some small cracks around the aluminum alloy intermetallic phase, whereas bath temperature and immersion time stimulated the conversion of the rare earths to more stable compounds, La2O3 and CeO2. During electrochemical evaluation, the CeCCs displayed a steady state potential at times longer than 250 min; as for LaCCs, longer time intervals were required to reach a stable potential. After covering with rare earth conversion films, the anticorrosive properties of the aluminum alloy were evidently improved. This enhancement is presumably due to the improved barrier properties of the anticorrosion product layer. Additional active corrosion protection was originated from the inhibiting action of the lanthanide ions trapped either as oxides or hydroxides in this surface layer.
Electrochemical/Chemical Deposition and Etching
D1
Hacer Dolas and A. Sezai Sarac
3-dodecylthiophene (3-dth) was electropolymerized onto platinum wire (Pt) in acetonitrile (ACN) containing different percentages of boron trifluoride diethyl etherate (BFEE) by using cyclic voltammetry (CV). The oxidation potential of the monomer was decreased by adding BFEE in ACN. The monomer was oxidized in pure BFEE at 0.78 V. The thickness of the film was reached to maximum value for 40% BFEE. Electrochemical impedance spectroscopy (EIS) measurements and Equivalent Circuit Modeling (ECM) were performed on the Pt/Poly (3-dth)/electrolyte system. The specific capacitance (Csp) value increased while the charge transfer resistance (Rct) value decreased with the increasing of concentration of BFEE. Rct value was 62.68 Ωcm2 for 100% BFEE. The highest Csp, 0.007 μFcm−2, and double layer capacitances (Cdl), 269 μFcm−2, were obtained for the film obtained in 100% BFEE. The inclusion of BFEE in the polymer structure was confirmed by Fourier Transform Infrared-Attenuated Total Reflectance (FTIR-ATR). Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) were used to investigate the polymer film deposited onto substrate in terms of morphology. The pore resistance (Rp) value was decreased with increasing the concentration of BFEE. As result of this the roughness of the polymer surface was decreased due to the decreasing of porous structure.
D9
Min-Gyu Kang, Seung-Min Oh, Kwang-Hwan Cho, Young-Ho Do, Dong-Soo Paik, Bong-Hee Cho, Chong-Yun Kang, Sahn Nahm and Seok-Jin Yoon
Low-temperature-crystallized PbZr0.52Ti0.48O3 (PZT) thin films, prepared using a sol-gel method, with a vanadium additive are demonstrated. The low crystallization and melting temperatures of vanadium oxide helped to reduce the crystallization temperature, and improved the grain growth in PZT thin films. Perovskite PZT thin films were obtained at a low annealing temperature of 450°C, and remarkable electrical properties such as a remnant polarization of 4.3 μC/cm2, a coercive field of 49.3 kV/cm, a dielectric constant of 585 at 1 MHz, a dielectric loss of 0.022 at 1 MHz, and a tunability of 64.5% were observed. The present results suggest that these low-temperature-crystallized PZT thin films could be used for integrated ferroelectric device applications.
D13
P. Veerender, S. P. Koiry, P. Jha, Vibha Saxena, A. K. Chauhan, S. Bhattacharya, R. Tewari, D. K. Aswal and S. K. Gupta
We present deposition of uniform polyfullerene films on ITO substrates using a novel electrochemical concept based on the oxidation of C60 dianion (C602−) solution. The C602− solution was prepared by the electroreduction of the C60 solution in dichloromethane and its oxidation at ITO surface was carried out using linear sweep voltammetry (LSV) in the −1 to 0 V range. The electrodeposited films were characterized by various techniques, such as, scanning electron microscopy, atomic force microscopy, Kelvin probe microscopy, high-resolution transmission electron microscopy, UV/Vis and Fourier transform infrared spectroscopy. The morphology of electrodeposited polyfullerene film was found to depend upon numbers of LSV scans used for its preparation. After 100 LSV scans, the films exhibited a globular morphology and were found to make a full coverage of ITO substrate. At higher scans, a second layer of polyfullerene was found to grow in the form of whiskers having length and diameter upto 200 and 0.4 μm, respectively. The energy band gap for polyfullerene whiskers was found to be ∼0.7 eV. Experimental evidence show that C60 polymerizes in the 1-dimensional “pearl-structure” via [2+2] cycloaddition reaction.
D19
Luda Lee and Sunjung Kim
Pure Cu substrate has been previously electroplated on p-GaN side of vertical structure GaN-based light emitting diode (LED) to mechanically hold thin GaN-based multilayer after removal of a sapphire substrate by laser lift-off process. The ductile Cu substrate needs to be mechanically strengthened to prevent the GaN-based multilayer from being damaged during vertical LED chip fabrication. In this study, the formation of Cu substrate with W addition on Au-seeded LED wafer by electroplating is introduced. W presents as WO3 in the Cu substrate. W content of W-added Cu deposits was dependent on constant reduction potential in an acidic citrate bath. The reduction potential also influenced directly the electrical resistivity, hardness, and residual stress of W-added Cu substrates. Applying moderate reduction potentials like −1.1 V resulted in 1.5 times larger hardness than that of pure Cu substrate by adding around 1.0 at % W to Cu. Nevertheless, the electrical resistivity of W-added Cu substrate was maintained as low as that of pure Cu substrate. At more positive reduction potentials than −1.1 V, very low residual stress between 4 and 42 MPa was measured. Wafer bowing induced by large residual stress of W-added Cu substrate can cause serious mechanical damage to LED structure.
D26
Jong-Chang Woo, Tae-Kyung Ha and Chang-Il Kim
In this study, the etching characteristics of HfAlO3 thin film were investigated by varying the etch parameters such as the gas mixing ratio, the radio frequency power, the direct current bias voltage, and the process pressure in an inductively coupled plasma. The maximum etch rate of HfAlO3 thin film and the selectivity of HfAlO3 to SiO2 were 20.55 nm/min and 0.38 in the CF4/Cl2/Ar (2:6:14 sccm) plasma, respectively. The plasma was analyzed by using optical emission spectroscopy. The chemical states on the surfaces of the etched HfAlO3 thin film were investigated with X-ray photoelectron spectroscopy. The etching of HfAlO3 thin films is performed by the interaction of Hf and Al atoms with the Cl and F radical in the CF4/Cl2/Ar plasma. However, their byproducts were remained at the surface because Hf-F and Al-F were non-volatile. Therefore, the plasma etching of the HfAlO3 films follows the ion assisted chemical reaction.
D31
Shou-Yi Chang, Jen-Yi Chen, Shau-Yu Wen and Tz-Yun Jian
In this study, hydroxyapatites were deposited on surface modified carbon fibers using a simulated body fluid; different amounts of COOH functional group were formed on the fiber surfaces by different degrees of KOH pretreatment. The effect of the surface functional group on the growth features of the hydroxyapatite crystals was analyzed, and the detailed stacking and structural correlations of the grown crystals to the substrate carbon fibers were examined to realize the mineralization mechanism. It was observed that hydroxyapatite nanocrystallites longitudinally constructed a crystal chain along [211] direction; several aligned crystal chains were then bundled to form a spindle structure which ultimately composed differently featured coatings. A mild KOH pretreatment created a small amount of functional group that activated few sites for hydroxyapatite nucleation compliant to the COOH bond structure, yielding a horizontally oriented olive structure under an orientation correlation HAP [112] or [211] // C [100]. A severer treatment induced more nucleation sites; attributed to the repulsion between the close COO− ligands, the bond structure was bent, leading to the radially aligned and ball-featured growth of hydroxyapatites with a different correlation HAP [112] or [211] // C [002].
Electrochemical Synthesis and Engineering
E1
Changsoon Choi, HyunJu Lee, Hee-Ryoung Cha, Jihye Gwak, Jae Ho Yun, Jong-Man Kim, Yangdo Kim and Dongyun Lee
CuIn(Ga)Se2 (CIGS) thin films were fabricated by electrochemical deposition method in a single bath in which ionized Cu, In, Ga, and Se were contained. The electrolyte was prepared by dissolving CuCl2, InCl3, GaCl3, H2SeO3, and LiCl (as pH adjuster) in deionized water. To modify the surface and microstructures of CIGS films, various amounts of gelatin were added in the solution. Potentiostatic deposition process was achieved by applying a voltage ranging from −640 to −1100 mV vs. Ag/AgCl. We prepared two different types of electrolyte baths for electrochemical deposition. All experiments were conducted at room temperature, and pH was adjusted about 2. As-deposited films were then annealed at 500°C in Ar for crystallization. Microstructures of fabricated CIGS films were observed by field emission scanning electron microscope. Crystallographic information was analyzed by high resolution X-ray diffractometer. The use of gelatin helped in fabricating crack-free CIGS thin films with greatly improved surface morphology. The improved morphological conditions resulting from grain refinement affected the structure of the post-annealed film as well. XRD data revealed that addition of excess gelatin causes fading of some of the CIGS peaks.
E5
M. Tokushige, H. Hongo, T. Nishikiori and Y. Ito
Sm-Co intermetallic compound nanoparticles were obtained by utilizing plasma-induced cathodic discharge electrolysis in molten chloride electrolyte under a 1 atm Ar atmosphere. To form intermetallic nanoparticle, an electrochemical implantation method was adopted. Before conducting electrochemical implantation, we investigated the electrolytic condition to form Co nanoparticle to be used as a precursor. The size and crystal structure of the obtained Co nanoparticle strongly depended on the melt temperature. Hexagonal petaline ɛ-Co nanoparticles were obtained below 400°C, and spherical α-Co nanoparticles were obtained above 400°C. The size of the obtained spherical α-Co particle increased from 112 to 230 nm with increasing melt temperature. Using spherical α-Co nanoparticles, which were formed at 450°C in the melt by plasma-induced cathodic discharge electrolysis and piled-up on the Mo plate as a working electrode, SmCo2 and SmCo3 intermetallic nanoparticles were obtained by electrochemical implantation of Sm into α-Co nanoparticles.
E11
Yan Kai Xu and Sadao Adachi
(NH4)2XF6:Mn4+ (X = Si, Ge, Sn, and Ti) red phosphors are synthesized by chemical reaction in (NH4)2XF6/HF/KMnO4/NH4F mixed solutions. X-ray diffraction curves indicate that the synthesized phosphors have a cubic symmetry with the space group
(X = Si) and a trigonal symmetry with the space group
(X = Ge, Sn, and Ti). Fourier-transform infrared spectroscopy, photoluminescence (PL) analysis, PL excitation (PLE) spectroscopy, and Raman scattering techniques are used to investigate the optical properties of the phosphors. The Franck − Condon analysis of the PLE spectra yields the Mn4+-related transitions to occur at ∼2.65 eV (4A2g → 4T2g) and at ∼3.4 eV (4A2g → 4T1g) in these phosphors. Temperature-dependent PL measurements are carried out from 20 to 350 K in steps of 10 K, and the obtained results are interpreted by taking into account the Bose−Einstein occupation factor. A complete set of internal vibronic frequencies, ν1 − ν6, for the
ions in (NH4)2XF6:Mn4+ are determined from the PL and Raman scattering measurements.
E18
A. C. Hee, I. H. S. C. Metselaar, M. R. Johan and M. Mehrali
In this study, nano nickel zinc ferrite powder with an average crystallite size of 23 ± 5 nm was synthesized by water-in-oil microemulsion technique. The coercivity value for the nickel zinc ferrite was 25.5 Oe which indicates soft ferromagnetic behaviour. The effect of the charging agent on the stability of the ferrite suspension was improved by analyzing the conductivity and zeta potential of the suspension. The findings show that the higher solid concentration led to lower suspension stability, lower electrophoretic mobility and electrophoretic deposition was carried out from the most stable ferrite suspension. A needle-like structure was observed on top of the surface of the ferrite layer. X-ray diffraction validated the composition of the ferrite layer formed.
Dielectric Science and Materials
G1
Osamu Tonomura, Tomoko Sekiguchi, Naomi Inada, Tomoyuki Hamada, Hiroshi Miki and Kazuyoshi Torii
A basic process to fabricate Ru/rutile-Co-doped TiO2/Ru capacitors for 20 nm-technology generation of DRAMs and beyond was developed. The aim of this study is that the basic process provides foresights into EOT and leakage-current density requirements. We chose rutile-TiO2 for the insulators to meet the requirement of relative permittivity and Ru to suppress leakage-current density. We found the as-deposited lower electrode of Ru crystallized into the rutile phase of TiO2 with a relative permittivity of 109 due to the similarity of crystal structures and lattice constants between rutile-TiO2 and rutile-RuO2, which was generated by oxidizing Ru with ambient oxygen. Furthermore, we confirmed that doping elements that had a small-ionic radius, such as Co, decreased leakage-current density. The dependence of the leakage current of Ru/Co-doped-TiO2/Ru capacitors on temperature and analysis of the band structure with X-ray photoelectron spectroscopy revealed that leakage-current density is determined by a balance between thermionic current and tunneling current through the Schottky barrier. Through calculations using a theoretical equation for these currents, the optimum percentage of Co was estimated to range from 0.3–0.6 % to meet requirement of leakage current for 20 nm- DRAMs.
G6
Young-Chul Byun, Chee-Hong An, Seok-Hee Lee, Mann-Ho Cho and Hyoungsub Kim
The simultaneous self-cleaning and passivation of an as-received GaAs substrate using trimethylaluminium (TMA) pretreatment before the atomic layer deposition (ALD) of HfO2 was systematically investigated. The change of the interfacial characteristics was probed as a function of the number of treatment cycles and the post-deposition annealing temperature and related with various electrical properties of the HfO2 film. The TMA pretreatment removed the Ga- and As-oxides more effectively than the ALD-HfO2 process, which reduced the amount of frequency dispersion. In addition, compared to the As case, it showed more predominant suppression of both Ga out-diffusion and Ga-O bond formation, which is believed to have delayed the thermal degradation of the capacitance equivalent thickness (CET). The optimal number of TMA treatment exhibited the best thermal stability without increasing the as-deposited CET.
Semiconductor Devices, Materials, and Processing
H1
Haigui Yang, Dong Wang and Hiroshi Nakashima
The effect of the insertion of a SiN film on the SiO2/4H-SiC interface properties was studied. The SiN interlayer was grown using electron cyclotron resonance (ECR) nitrogen plasma irradiation prior to the SiO2 deposition. It was found that the insertion of a SiN interlayer led to a significant decrease in interface-state and fixed-charge densities in a SiO2/4H-SiC gate stack. This insertion also induced elimination of the near-interface traps in the oxide. It was clarified from X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry analyses that Si dangling bonds were terminated by nitrogen, and the SiN interlayer effectively suppressed the formation of carbon generated by the thermal reaction between SiC and O atoms.
H5
A. P. Milenin, M. Demand, W. Boullart and P. Arleo
This paper reviews two types of sensor wafers that fit into the niche of spatially resolved in situ plasma diagnostics. The effect of both the incident power and the backside He flow on wafer surface temperature map was studied with the temperature sensor wafer. It was shown that the differential information related to the ion flux density distribution can be estimated in the case of two comparable recipe settings in a complementary way. Another sensor wafer is designed to measure the distribution of displacement current passing through the wafer. Calibrated at 13.56 MHz, it is capable of working in a wider range of source frequencies that has successfully been demonstrated in CCP reactors. It was found that the particular type of plasma reactor and the process chemistry selected can impact the level of correlation between the sensor and the blanket etch rate uniformity data.
H11
Song Ye, Nan Jiang, Jiajia Zhou, Deping Wang and Jianrong Qiu
The ZnO-LiYbO2 hybrid phosphors with various Yb2O3 and Li2CO3 starting concentrations were prepared by using the solid-state reaction method in a weak reducing atmosphere. Under the excitation of ZnO absorption with near-UV photons, the intense near infrared emission originated from Yb3+: 2F5/2 → 2F7/2 transition can be observed due to the efficient energy transfer from ZnO to Yb3+ ions. This efficient energy transfer is benefit from the introduction of Yb3+ ions into ZnO lattice at the interfacial diffusion layers between ZnO and LiYbO2 crystals. The luminescence decay of Yb3+ were recorded under the excitation of ZnO intrinsic absorption at 350 nm and excitonic absorption at 395 nm, in which the rise component can be clearly observed and the simulated rise lifetime that describing the population speed are 0.006 and 0.035 ms, respectively. The obvious different population speed of Yb3+: 2F5/2 excited level indicates two energy transfer mechanisms from ZnO to Yb3+: the cooperative energy transfer process under the excitation of intrinsic absorption and the phonon-assistant energy transfer process under the excitation of excitonic absorption, respectively.
H16
Sujith Subramanian, Ivana, Qian Zhou, Xingui Zhang, Mahendran Balakrishnan and Yee-Chia Yeo
Etch rates of Ni-InGaAs metallic film and Ni in HCl, HNO3, HF and SPM etch chemistries were determined using sheet resistance method, step height measurements, and cross sectional TEM characterization. HCl and HNO3 based chemistries were studied in detail. The etch selectivity of Ni over Ni-InGaAs in various etchants was studied. Concentrated HCl was found to have the highest selectivity of approximately 15.6. HNO3 (1:10) and HNO3 (1:20) solutions provides good selectivities of 4.3 and 4.5 respectively. The results of this work could be useful for the formation of Ni-InGaAs self-aligned source and drain in InGaAs N-MOSFETs.
H22
Dewen Zhao, Yongyong He and Xinchun Lu
In this paper, a novel in-situ interfacial fluid pressure measurement system is developed for the practical chemical mechanical polishing (CMP) equipment, in which the pressure sensors are equidistantly embedded in the platen along the radial direction and sweep beneath the wafer surface during CMP. Interfacial fluid pressure mapping is realized for standard 12″ blanket wafers at the down pressure of 0.5 ∼ 2.0 psi. The fluid pressure profiles from the leading edge to the trailing edge and the pressure contour maps of the fluid film across the whole wafer surface are constructed and displayed. Results reveal a large positive pressure region located near the wafer trailing edge and a small negative pressure region located near the leading edge, which is quite different from the negative dominated results of previous studies. The fluid pressure can support 15% ∼ 30% of the applied pressure. The down pressure has great effect on the fluid pressure due to the wafer's bend under the applied load. When the down pressure increases, the positive pressure region expands and slightly shifts toward the outer of the pad while the negative pressure region shrinks.
H29
Seung Mo Kang, Kyung Min Ahn and Byung Tae Ahn
The development of high-quality polycrystalline silicon film is of interest for active-matrix organic light-emitting displays. Here, NiCl2 vapor was applied for the first time to enhance the crystallization of amorphous silicon film. The crystallization of amorphous Si showed that round-shaped Si grains grow and become impinged to form polyhedral-shaped grains with diameters of 10 to 25 μm. It was found that the growth of large grains was possible via the merging of fine needle grains with the same directional growth. The crystallized film showed a high degree of crystallinity and a very smooth surface with a roughness of 0.53 nm. The field-effect hole mobility and subthreshold swing of the p-channel thin-film transistor fabricated using the poly-Si film were 113 cm2/
and 0.4 V/decade, respectively. The high performance of the thin-film transistor is attributed to the large grain size, the high crystallinity, the low Ni contamination and the smooth surface of the poly-Si film crystallized in NiCl2 vapor.
H33
A. Ashok Kumar, V. Rajagopal Reddy, V. Janardhanam, Min-Woo Seo, Hyobong Hong, Kyu-Sang Shin and Chel-Jong Choi
We investigated the electrical properties and reverse leakage mechanisms of Pt/n-Ge Schottky contacts with copper phthalocyanine (CuPc) as an interlayer. The current-voltage (I-V) and capacitance-voltage (C-V) characteristics of the Schottky contacts were used to evaluate Schottky barrier parameters such as ideality factor, barrier height, and series resistance. The barrier heights and ideality factors measured from the forward bias I-V characteristics were found to be 0.50 eV and 1.06 for Pt/n-Ge Schottky contact, and 0.58 eV and 1.31 for Pt/CuPc/n-Ge Schottky contact, respectively. Cheung method was used to measure the series resistances of the Schottky contacts, and the consistency was checked using the Norde method. The reverse leakage conduction mechanism of the Schottky contacts was investigated. Pt/CuPc/n-Ge Schottky contacts showed a transition from Schottky emission to Poole-Frenkel emission at a higher bias range. This could be associated with the high density of structural defects or traps associated with the organic material.
H38
Han-Ki Kim, Kyung-Jun Ahn, Hyungkeun Jang and Hosun Lee
The dependence of electrical, optical, structural, and surface properties on the thickness of Ga-doped ZnO (GZO) thin films deposited on glass substrates by cylindrical rotating magnetron sputtering (CRMS) was investigated. The resistivity of the CMRS-grown GZO films gradually decreased from 7.4×10−3 Ohm-cm to 4.9×10−4 Ohm-cm with increasing its thickness, while the transparency of the GZO films in visible region were kept constant regardless of its thickness. Both x-ray diffraction and high resolution electron microscope examinations showed that the CMRS-grown GZO film has a strongly (002) preferred orientation with increasing thickness even though it was sputtered at low substrate temperature below 230°C. By using spectroscopic ellipsometry, we estimated accurately the dielectric function and band gap energy of the CRMS grown GZO film. Using absorption coefficient α (= 4πk/λ) and linear extrapolation method, the band gap energy of the CRMS grown GZO film was estimated to be 3.67 ± 0.04 eV, which is independent of its thickness. However, we found that it gave erroneous thickness-dependence of band gap energy when we used the absorbance (= – ln(T)/d) derived from transmission rather than the absorption coefficient.
H44
R. A. Minamisawa, D. Buca, B. Holländer, J. M. Hartmann, K. K. Bourdelle and S. Mantl
We present a systematic study on the formation of p-type doped strained Si / strained SiGe heterostructures by B+, BF+2 and (Si++B+) ion implantation and annealing at moderate temperatures. The aim of this paper is to address the challenge of conserving the elastic strain during dopant activation. The most important result is that efficient doping combined with the conservation of strain and a good crystalline quality can only be obtained for BF2+ implants with 1×1015 ions/cm2 and anneals at 650°C. With these parameters, single crystalline layers with negligible strain relaxation and a sheet resistance of 886 Ω/sq were achieved. The implantation of B+ requires higher doses to reach low sheet resistances resulting in low layer quality and higher strain relaxation. Si+ pre-implantation yields the lowest sheet resistances, but on the expense of strain (relaxation values over 60%). Finally, the optimized ion implantation / anneal parameters were applied for strained SiGe quantum-well MOSFETs with GdScO3 high-κ gate dielectric.
H52
S. L. Liew, Y. Chai, H. R. Tan, H. K. Hui, A. S. W. Wong, G. K. Dalapati and D. Z. Chi
β-FeSi2 and Al were magnetron-sputtered onto n-Si(001) substrates and annealed by rapid thermal processing to form β-FeSi2(Al) thin films. The Al was incorporated through co-sputtering with β-FeSi2 and also as an interlayer between the co-sputtered film and Si substrate. FeSi2(Al) with atomic ratio of Al between 0.14 and 0.37 was polycrystalline, orthorhombic and semi-conducting. β-FeSi2(Al)/Si heterojunction solar cells were fabricated and characterized for photovoltaic properties. Under AM 1.5G, 100 mW/cm2 illumination, devices prepared with Al interlayers (1.5 to 9 nm thick) exhibited short-circuit current and open-circuit voltage improvement over device without interlayer. Spectral response measurements revealed that photocarriers contribution from β-FeSi2(Al) film and Si in the 300–700 nm and 700–1200 nm regions respectively, increased with Al concentration. The improvement in photovoltaic performance can be correlated to sharper FeSi2(Al)/Si interface for device with 1.5 nm thick Al interlayer and reduced dark current for 9 nm Al interlayer.
H57
Yi Zhao, Hirosaki Matsumoto, Susumu Koyama, Mitsuru Takenaka and Shinichi Takagi
In this study, we experimentally extract Si/SiO2 interface roughness of biaxially-tensile strained Si (s-Si) MOSFETs through high-resolution transmission electron microscopy (TEM) measurements with the different TEM sample thicknesses. The roughness-scattering-limited mobilities (μsr) of electrons and holes are calculated by using the digitalized SiO2/Si interface roughness data and applying the autoregressive (AR) model to the extraction of the power spectral density, S(q), of the interface roughness from the digitalization data. It is found that the roughness height, Δ, of the SiO2/Si interface, directly determined from the digitalized interface data, decreases with an increase in the TEM sample thickness due to the projection effect in the TEM image formation. As a result, the S(q) is underestimated and μsr is overestimated with an increase in the TEM sample thickness. The effectiveness of the linear S(q) correction is shown to be effective in representing the μsr values, which is verified by the simulation of the projection effect on the interface roughness observed in a TEM sample with an finite thickness.
Sensors and Displays: Principles, Materials, and Processing
J1
S. Asiri Naidu, U. V. Varadaraju and B. Raveau
Synthesis, crystal structure and optical properties of AgY0.95Eu0.05(WO4)2-x(MoO4)x and AgY1-xEux(MoO4)2 phases with scheelite related structures are described. The 5D0–7F2 electric dipole transition at 615 nm is predominant in the photoluminescence (PL) emission spectra, under 465 nm excitation. The critical concentration of Eu3+ is x = 0.5 in AgY1-x(MoO4)2, beyond which concentration quenching is observed. In AgY0.95Eu0.05(WO4)2-x(MoO4)x phases, the 5D0–7F2 emission intensity of Eu3+ is increased with the increase of Mo content.
J5
Jianfeng Sun, Wenlin Zhang, Youmin Shi, Dezhong Shen and Jiayue Sun
A series of new green-emitting Ca6Sr4-xEux(Si2O7)3Cl2 phosphors were synthesized using the high-temperature solid-state reaction. Thermogravimetry-differential thermal analysis (TG-DTA) and X-ray diffraction (XRD) were used in order to determine the crystallization process and crystal structure of the obtained product. Complete optical studies including the diffuse reflection, photoluminescence excitation and emission measurements were performed. Crystallographic site-occupations of Eu2+ ions in the Ca6Sr4(Si2O7)3Cl2 host were assigned and two distinguishable Eu2+ sites, viz., Eu(1)2+ and Eu(2)2+, were confirmed. The luminescence natures of the Eu2+ emission, e. g., the Stokes shift and the concentration-dependent luminescence behaviors were also investigated in detail. Based on the experimental results and theoretical calculation, the dipole-dipole interaction was dominantly involved in the energy transfer from Eu(1)2+ to Eu(2)2+ ions, and the critical distance was determined to be about 14.69 Å. The thermal-quenching behaviors were further presented. In view of its strong absorption in the near-UV region, the intense green light emission peaking at 511 nm, as well as the lower thermal quenching, the Eu2+-doped Ca6Sr4(Si2O7)3Cl2 phosphor can serve as a potential new material for phosphor-converted light-emitting diodes (LEDs).
J13
Z. Wang, X. Qiu, J. Shi and H. Yu
This study describes room temperature ozone sensing with a ZnO based film bulk acoustic resonator (FBAR). The resonant frequency of FBAR decreased upon ozone exposure. For 1400 ppb ozone, the frequency downshift was 131 kHz with a response time of 12 s. The frequency decrease of the FBAR sensor was proposed to be due to the density increase of the ZnO film. Ozone can be adsorbed on the ZnO surface by capturing free electrons from the film, which increases the film density. An analytical model was developed to predict the relationship between resonant frequency and ozone concentration. In agreement with the experiment, a hyperbolic function was obtained.
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K1
Hung-Yin Tsai and Chih-Cheng Yeh
Curvilineary tetrahedral diamond arrays of nano-tip with different pitches are firstly fabricated and the suppressed screening effects are also investigated. The curvilinear tetrahedral diamond arrays are fabricated by hot-filament chemical vapor deposition (HFCVD) on anodic aluminum oxide (AAO) template. The AAO template is fabricated by hard anodization. The diamond nano-particles are adhered onto the barrier layer of AAO template by Polyethylenimine pretreatment to increase the nucleation density of diamond. The diamond film is then deposited on the barrier layer of AAO by HFCVD. Curvilinear tetrahedral diamond arrays of nano-tip are developed after the removal of AAO template by wet chemical etching. The field emission effects of different diamond nano-tip arrays are measured by field emission meter. The morphology and quality of curvilinear tetrahedral diamond nano-tip array are examined by scanning electron microscopy and Raman spectroscopy, respectively. Innovative curvilinear tetrahedral structures are obtained successfully with the tip radius of 15 nm-30 nm, and the height of 100 nm-200 nm at different pitches from 50 nm to 300 nm. As a result, the lowest turn-on electric field of 5.4 V/μm and the highest field emission current density of 8.4 μA/cm2 can be obtained at the smallest pitch-height ratio of 0.25-1 without screening effect.
K5
Hsiao-Wei Lin, Yung-Huang Chang and Chih Chen
Self-organized anodic titanium dioxide nanorod arrays were fabricated using a two-stage anodization method from superimposed Ti-Al layers deposited on quartz substrates. The morphology of nanorods could be controlled by the anodizing conditions of the aluminum (first stage) and the titanium layer (second stage). The first stage of anodization process controls the diameter and density of nanorods and the second stage of anodization controls the height of nanorods. Therefore, we could fabricate nanorod arrays with desired aspect ratio and density under specific anodizing conditions. Furthermore, we used TiO2 nanorod arrays as the field ionization anode of a gas sensor, and the morphology of nanorods has shown to have a high correlation with the working voltage of gas sensing. The TiO2 nanorods possess good selectivity and low working voltage under different atmosphere and their working electric field is lower than gas sensing using carbon nanotubes and ZnO nanowires as the anode.
K10
Dong Chan Kim, Byung Oh Jung, Yong Hun Kwon and Hyung Koun Cho
Highly sensible ultraviolet (UV) photodetectors were fabricated using vertically aligned dense ZnO nanowires based on mechanical Schottky contact with Pt coated polyimides. The effective mechanical contact was achieved by depositing transparent Al-doped ZnO (AZO) buffer layers prior to the growth of the nanowires, resulting in highly uniform nanowires with similar lengths. The AZO buffer and ZnO nanowires were prepared by atomic layer deposition (ALD) and metalorganic chemical vapor deposition, respectively. The electrical conductivity of the nanowires was varied by controlling the density of oxygen vacancies by using a controlled oxygen flow rate. The high conducting nanowire-based photodetector concurrently achieved a high photocurrent signal, fast response, and fast recovery, compared with high conducting film and low conducting nanowire photodetectors. A detailed discussion regarding the developed UV photo-detecting mechanism by the different conductivities and Schottky contact is presented in this work.
K15
Ming Tan and Xinqi Chen
K21
Leonid Khriachtchev
Si nanocrystals in silica are attractive for photonic applications. Various optical functions can be realized in this way (for example, light emission). The optical and structural properties of a variety of such materials are described and compared here. It is found that Si nanocrystals with diameters 3-4 nm are not a direct source of the 1.5-eV photoluminescence. Furnace annealing at temperatures up to 1200°C does not complete the Si-SiO2 phase separation, and the suboxide phase and very small Si clusters should be accounted for when discussing light-emission mechanisms. Laser-induced thermal effects on optical and structural properties of free-standing films are described in detail. Laser annealing produces macroscopic Si-SiO2 phase separation and compressive stress on Si nanocrystals. The laser-induced structural changes offer an approach to optical memory with a high data density and superior thermal stability.
K27
V. Fernandes, I. L. Graff, J. Varalda, L. Amaral, P. Fichtner, D. Demaille, Y. Zheng, W. H. Schreiner and D. H. Mosca
The oxidation state of the cerium in ceria (CeO2) nanocrystalline films electrodeposited on Si(001) substrate was probed by three different complementary techniques: X-ray photoelectron spectroscopy (XPS), X-ray absorption near-edge structure (XANES) and electron energy loss spectroscopy (EELS). CeO2 films were prepared under different oxygenation conditions, and subsequently thermal annealed as well as submitted to 30 and 350 keV Ne+ irradiation with fluences ranging from 2 × 1014 to 2 × 1016 ions/cm2. Trivalent cerium concentrations higher than 50% were reached by using 30 keV Ne+ irradiation with high fluencies. Strong valence deviations in the film volume with specimen regions practically fully-reduced to CeO1.5 were obtained. These findings points out the potential for applications of low-cost nanocrystalline ceria thin films in many kinds of devices.
Interdisciplinary Topics
P1
Tae-Ki Woo, Seoung-Il Kim, Sarah Eunkyung Kim and Hyo-Sok Ahn
The dual-porous-structure (DPS) consisting of the amorphous porous structure (APS) and the defect-followed mesoporous structure (DMPS) was created using a new method combining the preferential etching and the stain etching on a grind damaged (001) silicon wafer. In this article, this novel pore-structuring technology, utilizing prominent reactivity of the intentional defect site produced by grind process, is introduced, and its procedures and the structural behaviors of the DPS are described by atomic force microscopy, transmission electron microscopy, scanning electron microscopy and 3D-profiling. Analysis of the optical properties proves that the broad photoluminescence intensity exists in the whole visible spectral range, and the light trapping functions of the antireflective coating and surface texture come from the APS and the DMPS, respectively. We also attempt to discuss about the absorption edge shift to the NIR spectral region using oblique angle of the DMPS. This original defect engineering approach is situated on viability of a rapid large area pore-structuring technology, and the optical properties were experimentally described for the first time.
P8
Jin Young Park, Hong Chae Jung, G. Seeta Rama Raju, Byung Kee Moon, Jung Hyun Jeong, Byung Chun Choi and Jung Hwan Kim
The Mesoporous TiO2 hollow spheres are synthesized by a solvothermal reaction without any surfactant and template. The reaction conditions such as reaction temperature, type of precursor, solvent used and their influence on the synthesis of TiO2 hollow spheres are investigated. The synthesized TiO2 hollow spheres are characterized by X-ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), focused ion beam (FIB) SEM, Barrett-Emmett-Teller (BET) surface areas, and UV-visible diffused reflectance spectroscopy. The synthesized TiO2 spheres have obtained different diameters ranging from 700 nm to 1.79 μm at different reaction temperatures. The shell is composed of numerous single crystalline nanoparticles. The morphology and interiors of the spheres strongly depend upon the experimental parameters such as reaction temperature and a kind of solvent. Especially, interiors of TiO2 hollow spheres such as mesoporous, double shell and single wall structures at various reaction temperatures are discussed with the aid of TEM and FIB SEM measurements.
P14
Rajaram Krishna Nagarale, Adam Heller and Woonsup Shin
Low-voltage non-gassing electro-osmotic pumps were built of phosphorylated silica frit membranes, formed meso-porous silica particles of 0.7-1.0 μm diameter, sandwiched between porous, consumable, Nafion-coated Ag/Ag2O electrodes. The flow rates of pumps with membranes formed of the meso-porous silica particles were stable, remaining constant within ±12% until ≥80% of the 2.6 coulomb capacity of the Ag or Ag2O electrodes, sufficient for pumping about 5 mL water, was exhausted. The cause of the decay of the flow in these pumps is Ag+-accumulation at the non-mesoporous membrane surface, observed by metallic silver precipitation caused blackening of the light-exposed non-mesoporous membranes. When the membranes were made with the mesoporous particles, there was no silver precipitate on the membrane; instead, all of the silver was electrodeposited at the cathode. The stability of the flow of pumps made with meso-porous silica membranes is thus attributed to the rapid transport of Ag+-transport to the cathode.
P18
Zai-Fa Pan, Cheng-Jing Zhu, Chang-Kui Duan, Juan Xu, Wen-Han Liu and Li-Li Wang
The SrMgB6O11 glass samples were synthesized by a solid-state reaction route. Luminescence of SrMgB6O11:Eu2+,Mn2+ shows a broad blue emission band and a red emission band, which originates from Eu2+ occupying the Sr2+ sites and Mn2+ occupying the Mg2+ sites, respectively. The obtained samples exhibit a tunable color emission under an ultraviolet source by adjusting the relative proportion of Eu2+/Mn2+ properly. The energy transfer from Eu2+ to Mn2+ in SrMgB6O11 is observed to be very effective. The optimal composition of SrMgB6O11:0.02Eu2+,0.12Mn2+ generates white light, indicating that the obtained glass would be a good candidate for white light-emitting diodes applications.
Miscellaneous
S1
J. Scheers and P. Johansson
S3
W. B. Liu, S. C. Zhang, N. Li, J. W. Zheng and Y. L. Xing