Articles
395
Craig R. Horne, Uwe Bergmann, Jaekook Kim, Kathryn A. Striebel, Arumugam Manthiram, Stephen P. Cramer and Elton J. Cairns
399
H. P. Chen, J. W. Fergus and B. Z. Jang
407
M. Mastragostino, C. Arbizzani, R. Paraventi and A. Zanelli
Supercapacitors are devices for applications requiring high operating power levels, such as secondary power sources in electric vehicles (EVs) to provide peak power for acceleration and hill climbing. While electronically conducting polymers yield different redox supercapacitor configurations, devices with the n‐doped polymer as the negative electrode and the p‐doped polymer as the positive one are the most promising for EV applications. Indeed, this type of supercapacitor has a high operating potential, is able to deliver all the doping charge and, when charged, has both electrodes in the conducting (p‐ and n‐doped) states. This study reports selection criteria for polymer materials and cell design for high performance EV supercapacitors and experimental results of selected polymer materials. © 2000 The Electrochemical Society. All rights reserved.
413
Sa Heum Kim, Wan M. Im, Jin K. Hong and Seung M. Oh
Cathode properties of two layered manganese dioxides
, where A is the pillaring alkali cations) having different crystal structures were compared in 3 V Li secondary batteries. The materials were prepared from the mixture of
, LiOH, and MnO at 800 and 1050°C, respectively. The 800°C‐prepared
has a trigonal
space group with an O3‐type oxide‐packing pattern, whereas the 1050°C material has an orthorhombic Cmcm symmetry with a P2‐type oxide‐packing pattern. The gallery space where the pillaring cations and water molecules reside is wider in the case of the 800°C material. Due to the higher mobility of pillaring cations in the 800°C material and similarity in the oxide‐packing pattern (O3‐type) to the spinel phases, the pillaring cations are easily leached out during cell cycling, which ultimately leads to a lattice collapse and structural transition to the spinel‐related phases. By contrast, as the 1050°C material has rather immobile pillaring cations and its oxide‐packing pattern (P2‐type) is far different from that of the spinel phases, this cathode shows better cycling performance, with its structural integrity being well maintained. © 2000 The Electrochemical Society. All rights reserved.
420
Katsuhiko Naoi, Shunzo Suematsu and Ari Manago
427
W. B. Gu, C. Y. Wang, John W. Weidner, Rudolph G. Jungst and Ganesan Nagasubramanian
A two‐dimensional model is developed to simulate discharge of a lithium/thionyl chloride primary battery. As in earlier one‐dimensional models, the model accounts for transport of species and charge, and electrode porosity variations and electrolyte flow induced by the volume reduction caused by electrochemical reactions. Numerical simulations are performed using a finite volume method of computational fluid dynamics. The predicted discharge curves for various temperatures show good agreement with published experimental data, and are essentially identical to results published for one‐dimensional models. The detailed two‐dimensional flow simulations show that the electrolyte is replenished from the cell head space predominantly through the separator into the front of the cathode during most parts of the discharge, especially for higher cell temperatures. © 2000 The Electrochemical Society. All rights reserved.
435
T. Armstrong, F. Prado, Y. Xia and A. Manthiram
439
Wensheng Huang, Pavel Shuk and Martha Greenblatt
444
Suh‐Cem Pang, Marc A. Anderson and Thomas W. Chapman
Thin films of manganese dioxide were formed on nickel foils by electrodeposition and by both dip‐coating and drop‐coating with manganese dioxide suspensions (sols) and their subsequent gelation and calcination. The performance of these films as ultracapacitors was studied by cyclic voltammetry in the range 0.0–0.9 V (SCE) and by chronopotentiometry in unbuffered
solution. The cyclic voltammograms of ultrathin, dip‐coated sol‐gel‐derived films indicated better capacitive behavior and gave differential specific capacitance values as high as 698 F/g compared to values half to two‐thirds as great for the electrodeposited films. Multilayer drop‐coated sol‐gel films were prepared to attain film thicknesses comparable to the electrodeposited films, and these were found to provide charge‐storage capacity as high as
, more than three times greater than that of the electrodeposited films. All films, except electrodeposited films that were not thermally cured, exhibited good cycling stability, losing not much more than 10% of capacity after 1500 cycles. © 2000 The Electrochemical Society. All rights reserved.
451
G. B. Appetecchi, M. Carewska, F. Alessandrini, P. P. Prosini and S. Passerini
This report describes the fabrication and characterization of polymer‐based composite cathode membranes intended for use in polymer‐electrolyte batteries operating at moderate temperatures (60–100°C). The present work is focused on the determination of morphological, thermal, mechanical, and electrical properties of PEO‐based composite cathodes. The work was developed within the Advanced Lithium Polymer Electrolyte project (ALPE), an Italian integrated project devoted to the realization of lithium polymer batteries for electric vehicle applications. © 2000 The Electrochemical Society. All rights reserved.
460
Jun‐ichi Yamaki, Minato Egashira and Shigeto Okada
Lithium graphite intercalation compound (Li‐GIC) has potential plateaus depending on its staging in Li/Li‐GIC cells. It is believed that the entropy of each stage is different depending on the total number of states created by the inserted
and electrons in Li‐GIC. On this basis, the entropy change with Li insertion has been calculated and the potential, using the reaction Gibbs function, has been estimated. The entropy term in the usual potential equation diverges for Li vacant and Li full GICs. The equation was improved and had finite values for these GICs depending on the mean size of the crystallites in the GIC. By the introduction of the intercalation pressure to our model, we confirmed that Li‐GIC is unstable and decomposes into Li‐poor and Li‐rich phases. The potential was calculated using the entropy term for Li full GIC. The result agreed well with the experimental value. The entropy term contribution was very large for the potential difference of each plateau. © 2000 The Electrochemical Society. All rights reserved.
466
Xiaoming Ren, Thomas E. Springer, Thomas A. Zawodzinski and Shimshon Gottesfeld
475
M. Brown, S. Primdahl and M. Mogensen
486
P. E. de Jongh, D. Vanmaekelbergh and J. J. Kelly
The photoelectrochemical properties of electrodeposited
in aqueous solutions were investigated. The material showed long term stability under illumination at negative potentials. The diffusion length of electrons in the as‐deposited material was of the order of 10–100 nm. We did not observe photocathodic reduction of water. The efficiencies for the reduction of oxygen and the methylviologen cation at these electrodes were surprisingly high. This suggests that, in conjunction with a suitable redox system, electrodeposited
could be a promising material as a p‐type photoelectrode in an electrochemical photovoltaic cell. © 2000 The Electrochemical Society. All rights reserved.
490
M. Mohamedi, Y. Hisamitsu, Y. Ono, T. Itoh and I. Uchida
The reduction of oxygen at a gold flag electrode fully immersed in
was investigated at different temperatures (600∼750°C) using cyclic voltammetry and the semi‐integral method. It was found that the electrode reaction mechanism depends critically on the scan rate and temperature. The overall mechanism is complicated by adsorption phenomena. This was identified via semi‐integral analysis by the appearance of a peak‐shaped semi‐integrated voltammetric response. An electron transfer number equal to 2 was determined by the simultaneous use of the voltammetric peak and the maximum value of the semi‐integral curve. Both the initial surface excess, Γ*, and the mass‐transfer parameter
could be determined from the semi‐integration of a single voltammogram. © 2000 The Electrochemical Society. All rights reserved.
496
S. Licht, R. Tel‐Vered, G. Levitin and C. Yarnitzky
The use of solution activators (dissolved metal salts) to enhance aluminum electrochemical activity in organic media is reported. Aluminum is electrochemically passive in most organic electrolytes and unlike lithium, has not been developed as a battery anode in organic media. We demonstrate significant Al activity in two electrolytes,
in γ‐butyrolactone or
in acetonitrile. These improve the anodic potential by up to 1 V in comparison to other electrolytes and increase from microampere to milliampere per square centimeter, the sustainable Al oxidation current. Electrolytic metal acetate, chloride, or other salts can further enhance these favorable anodic characteristics. Unlike Sn(II), Sn(IV), or Ga(III), both Hg(II) and In(III) significantly activate Al redox behavior. In
, the Al oxidative polarization is 100, 65, 36, or only 28 Ω
in electrolytes containing, respectively, 0, 1, 10, 100 mM Hg(II). Hg(II) also shifts negatively the observed
by 150 to 250 mV, an enhancement sustained during extended anodic galvanostatic discharge. Similarly, as little as 1 mM In(III) diminishes polarization to 40 Ω
Addition of 10 mM In(II) to
in acetonitrile, improves
by 0.4 to −1.57 V vs.
. © 2000 The Electrochemical Society. All rights reserved.
502
Jai Prakash, Laszlo Redey and Donald R. Vissers
508
J. M. Paulsen, J. R. Mueller‐Neuhaus and J. R. Dahn
517
B. J. Neudecker, N. J. Dudney and J. B. Bates
524
Koji Fushimi, Tsuyoshi Okawa, Kazuhisa Azumi and Masahiro Seo
A scanning electrochemical microscope (SECM) was applied to study anodic oxide film grown on a polycrystalline titanium electrode in deaerated pH 8.4 borate solution. The probe current images of SECM could detect the heterogeneous growth of anodic oxide film, depending on the substrate crystal grains. This heterogeneity increased with increasing the film formation potential at the potential higher than 3 V (SHE). The study of the dependence of film thickness on the substrate grain has been also supported with Raman microprobe spectroscopy. © 2000 The Electrochemical Society. All rights reserved.
530
Y. J. Tan, S. Bailey, B. Kinsella and A. Lowe
A wire beam electrode (WBE) has been used, in conjunction with the electrochemical noise resistance method, to determine the kinetics of nonuniform corrosion of mild steel in a carbon dioxide saturated brine. Local electrochemical parameters including corrosion potential, galvanic current, and electrochemical noise resistance were measured from local areas of a WBE surface. These parameters were used to calculate the kinetics of local electrochemical corrosion processes. A map showing instantaneous corrosion rate distribution over a WBE surface has been produced. Corrosion depths were calculated, based on instantaneous corrosion rate data, at various stages of the corrosion exposure period, and these were summed up to produce an accumulated corrosion depth map. This accumulated corrosion depth map was found to be quantitatively comparable with a microscopically observed corrosion depth map. This work shows that electrochemical corrosion kinetics can be determined using kinetic equations previously derived based on the WBE concept. This work also shows that the WBE is a novel electrode design which is suitable for performing electrochemical noise resistance measurement and that the WBE is applicable to practical corrosion conditions. © 2000 The Electrochemical Society. All rights reserved.
540
Carol S. Jeffcoate, Hugh S. Isaacs, Antonio J. Aldykiewicz Jr and Mary P. Ryan
Samples of pure aluminum were prepared with four different areas on one surface: etched aluminum, etched aluminum exposed to various electrolytes, Alodine treated aluminum, and Alodine treated aluminum exposed to electrolyte. X‐ray absorption near‐edge structure (XANES) was used to measure both the distribution of chromium and the proportion of hexavalent chromium. The spatial distribution of the chromium species was mapped following exposure to a range of electrolytes: Samples were exposed for 499 and 835 h to 18 MΩ deionized water, 0.5 M NaCl,
, and
. Immersion in water and sulfate had a minimal effect on the ionic state and location of chromium species. Immersion in chloride induced crevice corrosion attack, as indicated by a reduction in the Cr content at the interface between the exposed and protected Alodine treated areas. Small losses in Cr attributable to the loss of Cr(VI) were also found on the exposed Alodine treated areas. Exposure to sulfite caused the most dramatic changes. The total chromium content of the exposed Alodine decreased by 13%, and the amount of Cr(VI) decreased by 69% of its original value. There was a marked deposition of chromium as Cr(III) on the etched exposed aluminum close to the Alodine interface. © 2000 The Electrochemical Society. All rights reserved.
548
R. Gašparac, C. R. Martin and E. Stupnišek‐Lisac
The objective of this work was to investigate the efficiency of imidazole and its derivatives 4‐methylimidazole, 4‐methyl‐5‐hydroxy‐methylimidazole, 1‐lphenyl‐4‐methylimidazole, and 1‐(p‐tolyl)‐4‐methylimidazole for corrosion inhibition of copper in 0.5 M hydrochloric acid. Corrosion inhibition was studied using potentiodynamic methods. These studies have shown that 1‐(p‐tolyl)‐4‐methylimidazole has the best inhibitory efficiency. Activation energies were obtained by measuring the temperature dependence of the corrosion current. The activation energies in the presence of the various inhibitors are low (3–5 kJ/mol), with the best inhibitor showing the highest value. The adsorptive behavior of the imidazole derivatives on the copper electrode surface follows a Freundlich‐type isotherm. The standard free energies of adsorption are also low (14–16 kJ/mol), indicating that imidazole and its derivatives physisorb on the copper surface. Possible mechanisms of corrosion inhibition for these molecules are discussed. © 2000 The Electrochemical Society. All rights reserved.
552
Koji Fushimi, Kazuhisa Azumi and Masahiro Seo
A silver/silver chloride microelectrode was developed as a liquid‐phase ion gun for investigation of precursor processes of pitting corrosion. This electrode was set as a probe electrode of a scanning electrochemical microscope and used to induce a local breakdown of passive film on iron. A small amount of chloride ions generated by cathodic polarization of the silver/silver chloride micro‐electrode has succeeded in inducing the local breakdown of the passive film formed on iron in deaerated pH 6.5 borate solution. Moreover, the microelectrode could detect ferric ions dissolved from the film at the initial stage of the film breakdown. © 2000 The Electrochemical Society. All rights reserved.
558
H.‐C. Xu, G. Seshadri and J. A. Kelber
Combined ultrahigh vacuum electrochemistry is applied to study the effect of sulfur on copper oxidation in aqueous solution. Chronoamperametric studies show that pulsing a Cu electrode modified with ∼0.1 monolayer of adsorbed S results in an approximately 50 s plateau in the current‐time profile after a slight initial decay in current. Following the plateau period, the current‐time profile is observed to exhibit a final phase of current decay. In contrast, a S‐free copper electrode exhibits immediate current decay. X‐ray photoelectron spectroscopy analysis reveals that
is the main oxide growing on both S‐free and S‐modified copper surfaces under these conditions. On the S‐free copper surface, oxide covers the surface almost immediately after the pulse. On the S‐modified copper surface, oxide growth continues for ∼70 s after the pulse. The data indicates that the final phase of current decay on the S‐modified Cu surface occurs only when oxide growth is essentially complete. Oxide growth is significantly retarded by the presence of sulfur. © 2000 The Electrochemical Society. All rights reserved.
562
Jae‐Joon Lee, In Tae Bae, Daniel A. Scherson, Barry Miller and Kraig A. Wheeler
Interfacial processes occurring at polycrystalline gold in acidic 1‐ethyl‐3‐methylimidazolium chloroaluminate melts at room temperature, at potentials more positive than aluminum bulk deposition, include both Al underpotential deposition and the formation of Al/Au alloys. This information complements that reported in the literature for Al electrodeposition on Au in
melts at temperatures of 200°C and higher. Cyclic voltammetry and chronopotentiometry suggest that at least two alloys form, and there is fast phase transformation between these intermetallic compounds at room temperature in the aluminum underpotential region. This transformation with thin gold films was slower than that in bulk gold electrodes. © 2000 The Electrochemical Society. All rights reserved.
567
E. Gileadi and V. Tsionsky
The electroplating of silver and copper has been studied using an electrochemical quartz crystal microbalance (EQCM). Deposition of Ag on Ag follows the expected behavior. For deposition of Cu, the linearity between frequency shift and added mass is maintained, but the slope is smaller (in absolute value). This is attributed to the formation of
ions, which diffuse in part into the bulk of the solution, without being further reduced. Pourbaix‐type diagrams have been developed, showing the regions of thermodynamic stability of the cuprous ions in aqueous solutions, in the absence of complexing agents. In the early stages of deposition of both metals on a gold surface, large deviations of the frequency shift from its calculated value are observed. For Ag, this deviation is due to the difference in the interaction of Au and Ag with the solvent. When Cu is deposited on gold, the deviation is also due to stress in the deposit. This stress, resulting from the difference in crystal parameters between gold and copper, can be relaxed partially at open circuit at room temperature. © 2000 The Electrochemical Society. All rights reserved.
575
Chrystel Faure, Serge Ravaine and Francoise Argoul
Incorporating particles in a solid matrix to improve its surface properties has been performed by electrodeposition since the beginning of this century. The present challenge is to find new types of particles which confer original properties on the material. This work focused on the embodying of new particles, called spherulites, into a metal hydroxide layer by electrolytic codeposition. The novelty of these colloidal particles results from their ability to encapsulate arbitrary compounds. They are prepared by manually shearing a lamellar phase and then are dispersed into an aqueous electrolyte. The layering of these particles, concomitantly to the formation of the metal hydroxide layer, is observed in situ by phase contrast microscopy. Their engulfing is confirmed by scanning electron microscopy, atomic force microscopy, and Auger electron spectroscopy. These analyses provide evidence for zinc hydroxide coprecipitation on the cathode surface simultaneous to the spherulite engulfing. © 2000 The Electrochemical Society. All rights reserved.
580
Tetsuya Homma, Akito Takasaki, Masaki Yamaguchi, Hiroshi Kokubun and Hideaki Machida
A new technique of copper (Cu) film deposition by simple pyrolysis of copper hexafluoroacetylacetonate vinyltrimethylsilane
in liquid phase has been proposed. The Cu films were deposited in air and nitrogen
ambiences as a function of substrate temperature. Both Cu films show grain‐like structures, and the grain size increased with increasing deposition temperature. X‐ray diffraction patterns for all Cu films deposited in air and N2 show the diffraction peaks corresponding to (111), (200), (220), and (311) crystal planes of Cu. The difference in lattice constant between the deposited Cu films and bulk Cu is less than 0.3%. The Cu films contain oxygen (O), carbon (C), and fluorine (F) as impurities. The relative concentrations of O, C, and F atoms are less than 10 atom %. The relative Cu concentrations in the films are over 80 atom %. The resistivity values for Cu films deposited at 250°C in air and N2 ambiences were 65 and 46 μΩ‐cm, respectively. The differences between this deposition method and metallorganic chemical vapor deposition is also discussed. © 2000 The Electrochemical Society. All rights reserved.
586
E. M. El‐Giar, R. A. Said, G. E. Bridges and D. J. Thomson
This work demonstrates the electrodeposition of micrometer‐scale copper structures using a simple instrument based on the scanning electrochemical microscope (SECM). Copper columns of 25 μm width up to about 2 mm high were deposited on different substrates and interconnects were grown within an integrated circuit package. In the present instrument electrodeposition is localized by applying a voltage between a closely spaced glass insulated Pt disk ultramicroelectrode, ca. 25 μm diam, and a substrate, all immersed in a solution of acidified
. The potential, the concentration of the
, and the presence of organic additives were all found to affect the microstructure of the deposits and control the efficiency of the deposition. To demonstrate some of the possible applications of this technique, copper lines were grown between pads in an integrated circuit package and an antenna about 2 cm long was grown on a millimeter wave transmission line cantilever. © 2000 The Electrochemical Society. All rights reserved.
592
F. Bonfatti, S. Ferro, F. Lavezzo, M. Malacarne, G. Lodi and A. De Battisti
597
Guillaume Herlem, Karine Reybier, Albert Trokourey and Bernard Fahys
602
T. Monguchi, H. Fujioka, K. Ono, Y. Baba and M. Oshima
A room‐temperature wet process which allows control of the wavelength of photoluminescence from porous silicon has been developed. This process reduces the size of the silicon crystal by the repeated formation and removal of the surface oxide. It has been learned that the surface after this process does not have residual oxide. Synchrotron radiation photoemission spectroscopy and X‐ray absorption near edge structure measurements have revealed that the bandgap of porous silicon becomes wide with repetition of our wet process. © 2000 The Electrochemical Society. All rights reserved.
606
Long Cheng and Shaojun Dong
613
Hiroaki Tada, Miwako Yamamoto and Seishiro Ito
617
Stephen J. Paddison, Reginald Paul and Thomas A. Zawodzinski Jr.
627
M. Hejjo Al Rifai, M. Christophersen, S. Ottow, J. Carstensen and H. Föll
Subjecting illuminated n‐type silicon wafers to anodic bias in an HF containing electrolyte results in the formation of macropores under certain conditions. In this paper the formation of randomly nucleated macropores is studied as a function of the applied potential, the temperature, and the doping levels of the samples. A large number of micrographs was evaluated by computerized image processing and the data obtained are compared to predictions of pore formation models. It was found that the formation of randomly nucleated macropores involves a prolonged nucleation phase. Starting from a polished surface, first macropores occur after a certain amount of Si has been homogeneously dissolved. In this nucleation phase the thickness of the homogeneously dissolved Si depends strongly on the doping level and the temperature, but only weakly on the applied bias. In a second phase of stable pore growth, the density of pores is investigated as a function of temperature and anodic potential. For low‐doped material a strong influence of the space‐charge region on the average macropore density is observed in accordance with existing models; an increased anodic bias, e.g., decreases the density of pores. For highly doped silicon the situation reverses; increasing anodic bias increases the pore density, in contrast to predictions. The pore growth in this region is not very sensitive to the space‐charge region but seems to be dominated by the chemical‐transfer rate. © 2000 The Electrochemical Society. All rights reserved.
636
S. Strehlke, S. Bastide, O. Polgar, M. Fried and Lévy Clément
642
Y. Sakamura, O. Shirai, T. Iwai and Y. Suzuki
Thermodynamic properties of neptunium in LiCl‐KCl eutectic/liquid bismuth systems in the temperature range 400–500°C have been studied using a galvanic cell method for the pyrometallurgical reprocessing of nuclear spent fuels. The standard potential of the Np/Np(III) couple vs. the Ag/AgCl (1 wt % AgCl) reference electrode in LiCl‐KCl eutectic was measured and given by the equation
, where E is in volts, T is in kelvin, and σ is the standard deviation. The potential of neptunium‐bismuth alloy,
, was measured as a function of neptunium concentration,
. The curves for
vs. log
indicated the neptunium solubility in liquid bismuth to be 0.34 ± 0.02, 0.61 ± 0.08, and 1.06 ± 0.09 (±σ) atom % at 400, 450, and 500°C, respectively. The excess partial free energy of neptunium in liquid bismuth was represented by the equation,
. The values of the solubility and excess partial free energy for neptunium were closer to those for plutonium rather than uranium. © 2000 The Electrochemical Society. All rights reserved.
650
Hyun‐Gon Lee, Heung‐Shik Park, Hyun‐Eui Lim, Yeonhee Lee and Kang‐Jin Kim
655
V. Petrovich, S. Volchek, L. Dolgyi, V. Yakovtseva, V. Bondarenko, M. Balucani, G. Lamedica, A. Ferrari, T. Benson and H. Arrand
The chemical processes that occur during the electrochemical treatment of a porous silicon cathode in aqueous solutions of erbium salts are studied. The results obtained show that (i) erbium ions do not take place in the electrochemical reactions and (ii) erbium‐containing deposits are formed by chemical reactions at the cathode. The chemical composition and structure of the deposits can be varied by controlling the electrolysis conditions. These observations facilitate the future design of process cells suitable for the effective incorporation of erbium and other rare earth elements into oxidized porous silicon waveguides for optical amplifier applications. © 2000 The Electrochemical Society. All rights reserved.
659
K. Honda, Tata N. Rao, D. A. Tryk, A. Fujishima, M. Watanabe, K. Yasui and H. Masuda
665
Hamilton Varela and Roberto M. Torresi
Polyaniline films in nonaqueous media, mainly propylene carbonate and acetonitrile, are studied by using simultaneous potentio‐dynamic experiments with the electrochemical quartz crystal microbalance and electrochemical impedance spectroscopy. The role of ionic transport and solvent participation during redox reactions is emphasized to obtain information about all chemical species involved in the process occurring in the conducting polymer film. The contribution of each species (neutral and ionic) depends on both the chemical nature of the ionic salt and the solvent used. Quartz crystal microbalance results have shown that both cation and anion contribute to the electroneutralization process, and the participation of solvent molecules is related mainly to changes in the oxidation state of the polymer matrix. As propylene carbonate propylene (ε = 66.1) is a more polar solvent than acetonitrile (ε = 37.3) it produces a more pronounced swelling process. © 2000 The Electrochemical Society. All rights reserved.
671
I. N. Bastos, F. Huet, R. P. Nogueira and P. Rousseau
This paper points out the importance of anti‐aliasing filtering in the analog‐to‐digital conversion performed in electrochemical noise (EN) measurements. This operation is currently implemented in spectrum analyzers, but it is generally ignored in data acquisition systems based on acquisition cards in personal computers or on digital voltmeters. It is shown that without filtering, aliasing occurs and leads to fallacious amplitudes of the EN, that is, too‐high standard deviations in the time domain and too‐high power spectral density levels in the frequency domain. In particular the white noises, which are commonly encountered in localized corrosion at low sampling rates, always have a wrong amplitude when measured without filtering. Anti‐aliasing filtering may be carried out with analog filters or a combination of analog and digital filters. A comparison of two different digital filters, which are easily implementable in personal computers, shows that the slope of the filter roll‐off has to be high enough to avoid aliasing for all types of EN and to obtain a good overlapping of the power spectral densities measured at various sampling rates. © 2000 The Electrochemical Society. All rights reserved.
678
Catherine B. Labelle and Karen K. Gleason
682
Simon J. Fang, Santos Garza, Honglin Guo, Taber H. Smith, Greg B. Shinn, John E. Campbell and Michelle L. Hartsell
Since a premetal dielectric (PMD) is used in the first level of interconnects, tight control of the critical dimension of the subsequent first‐level contact is essential. The thickness nonuniformity due to PMD chemical mechanical polishing (CMP) can consume most of the depth‐of‐focus budget for the deep UV lithographic process. In this paper, we first describe a low pressure/high speed CMP process for PMD. Using a polishing pressure of only 2.5 psi, we improve the within die nonuniformity by 20–30%. To meet the throughput requirement, we can achieve a very high polish rate (>5000 Å/min) by using high rotational speeds. Second, we describe an integrated noncontact clean to achieve low post‐CMP defect counts and metallic contaminations. Cleaning phosphosilicate glass (PSG) is generally more difficult than undoped oxides. Because PSG is softer than an undoped oxide, it usually has more microscratches. Because phosphorous acts as a gettering center for metallic impurities, PSG can have high metallic contamination after post‐CMP clean. HF immersion can greatly reduce the metallic contamination, but it enlarges the microscratches, leading to a large number of detectable defects. Mechanisms for the removal of slurry residue, microscratches, and metallic contamination are discussed in this paper. © 2000 The Electrochemical Society. All rights reserved.
687
M. E. Rodriguez, A. Mandelis, G. Pan, L. Nicolaides, J. A. Garcia and Y. Riopel
A laser infrared photothermal radiometric (PTR) multiparameter‐fit methodology has been developed to obtain unique measurements of the thermal and electronic parameters of industrial‐type Si wafers. The influence of recombination lifetime, front, and back surface recombination velocities, carrier electronic diffusion coefficient, thermal diffusivity (α), as well as of the total plasma and thermal contributions to the PTR signal as a function of frequency is examined computationally and experimentally in this paper. Silicon wafers with low and high resistivity were studied with the proposed methodology. A strong correlation between nominal resistivity, front surface recombination velocity, and recombination lifetime was found: higher resistivity wafers are likely to have lower surface recombination velocity and longer lifetimes. The first PTR lifetime scanned image of subsurface electronic defects has also been produced. © 2000 The Electrochemical Society. All rights reserved.
699
Fu‐Chu Chou and Pei‐Ying Wu
706
P. Wrschka, J. Hernandez, G. S. Oehrlein and J. King
We describe the chemical mechanical planarization (CMP) of copper damascene structures using an IC1400 pad and four different types of slurries. Two alumina‐based slurries and two silica‐based slurries were evaluated. After successful removal of the excess Cu, we examined the topography of the planarized structures using scanning electron microscopy. The effects of the CMP process on spacer erosion, Cu line recess, corrosion of submicrometer Cu lines, liner removal selectivity, and contamination of the patterned structures are presented. It was found that minimizing the etch rate (∼10 nm/min) of the slurry is required to achieve reproducible removal rates and unrecessed (etched) damascene structures. No dishing was observed with the utilized pad. We also show that corrosion is prone to occur in low Cu pattern density areas and that the removal of the liner material (tantalum) remains problematic because of its chemical inertness. © 2000 The Electrochemical Society. All rights reserved.
713
Jing‐Cheng Lin and Chiapyng Lee
Tantalum nitride
films are deposited on silicon substrates by radio frequency (rf) reactive sputtering of Ta in
gas mixtures. The deposition rate, chemical composition, and crystalline microstructure are investigated by cross‐sectional‐transmission electron microscopy, X‐ray photoelectron spectroscopy, Auger electron spectroscopy, X‐ray diffraction, and atomic force microscopy, respectively. According to those results, the deposition rate, film composition, and microstructure correlate with the bias. A stepwise change in deposition rate is observed at a
flow ratio of 0.2 for all biases. The deposition rate increases with the bias throughout the whole range of
flow ratio. Crystalline TaN can be deposited on Si substrates at a
flow ratio of 0.25 and all biases. The TaN lattice is distorted due to the change of N concentration. In addition, the experimental data which were interpreted using the deposition mechanism and the kinetic model which were published previously. © 2000 The Electrochemical Society. All rights reserved.
719
A. P. Zhang, G. Dang, F. Ren, X. A. Cao, H. Cho, E. S. Lambers, S. J. Pearton, R. J. Shul, L. Zhang, A. G. Baca et al
Inductively coupled plasma etching of metallized GaN Schottky diodes in
discharges produces reductions in both reverse breakdown voltage and Schottky barrier height. The extent of these reductions is a function of both ion energy and ion flux. Two different postetch treatments were performed in an attempt to remove the ion‐damaged GaN surface layer, namely, annealing in
or UV‐ozone oxidation followed by dissolution of the oxide. Both treatments provide only partial restoration of the diode properties. © 2000 The Electrochemical Society. All rights reserved.
723
D. Yang, J. J. Kristof, R. Jonnalagadda, B. R. Rogers, J. T. Hillman, R. F. Foster and T. S. Cale
Programmed rate chemical vapor deposition (PRCVD), in which conditions are systematically changed during deposition, studies of tungsten and aluminum are presented. In the tungsten study, PRCVD provided significantly greater throughput than conventional, constant rate CVD (CRCVD). We started the deposition process at a much higher rate then decreased the temperature during deposition. We achieved throughput increases of about a factor of three, with more improvement clearly obtainable. In addition to the increase in throughput, the properties of the PRCVD films were equal to, or superior to, CRCVD films. In the aluminum study, we demonstrated that PRCVD processes can yield films with better properties than CRCVD processes. PRCVD films can have higher nuclei densities, higher fractions of (111) orientated Al, lower surface roughnesses, higher reflectivities, and resistivities closer to that of bulk aluminum. For example, pulsing (starting and stopping) the precursor flow at the start of the temperature ramp down (−200 K/min) from 673 K (for 5 or 10 s), followed by deposition at 573 K yielded better films than similar traditional CRCVD processes. In general, PRCVD protocols provide degrees of freedom that can be used to improve processing or film properties. © 2000 The Electrochemical Society. All rights reserved.
731
D. Landheer, K. Rajesh, J. E. Hulse, G. I. Sproule, J. McCaffrey, T. Quance and M. J. Graham
736
D. Martin Knotter, Stefan de Gendt, Paul W. Mertens and Marc M. Heyns
Silicon wafers were exposed to a cleaning sequence containing an HF etching step prior to an ammonia hydrogen peroxide mixture (APM) (or SC1) cleaning treatment. These wafers are subject to roughening according to at least three mechanisms. One roughening mechanism is due to the vapor from the APM mixture, while the other two are strongly related to metal contamination. At first, ammonia vapor from a hot APM solution will condense on the cold hydrophobic wafer surface and will etch the surface. Second, iron‐ion contamination (present as iron hydroxide aggregates in the APM), will catalyze the hydrogen peroxide decomposition. During immersion of the wafer, these iron‐ion aggregates can deposit on the silicon surface. Therefore, local hydrogen peroxide depletion is created, as these aggregates continue to catalyze its decomposition. This causes local etching of the silicon in typical rings having a depth of 2–5 nm, while a rim of 3–8 nm of a silicon oxide is deposited next to the ring. Finally, metals such as copper and nickel can plate on the silicon wafer in the HF step prior to the APM step. They act as the cathode in a galvanic cell while the silicon surrounding the copper (or nickel) nuclei is dissolving anodically. © 2000 The Electrochemical Society. All rights reserved.
741
Takuo Monguchi, Hiroshi Fujioka, Takeshi Uragami, Hironobu Ohuchi, Kanta Ono, Yuji Baba and Masaharu Oshima
We have succeeded in anodizing single crystal 3C‐SiC and performed X‐ray absorption studies before and after the anodization. Silicon K‐edge X‐ray absorption near edge structure reveals that the anodization causes slight changes in the electronic state of the conduction band. The conduction band minimum shifts toward higher energy after the anodization. Extended X‐ray absorption fine structure, however, shows no changes in the local crystal structure such as bond length and coordination number. © 2000 The Electrochemical Society. All rights reserved.
744
D. Jahan, D. Söderström and S. Lourdudoss
A kinetic study of InP:Fe growth has been carried out in a low pressure hydride vapor phase epitaxy (LP‐HVPE) reactor using ferrocene as iron source. The influence of the ferrocene partial pressure on the growth behavior has been investigated. A drastic decrease of the growth rate in the presence of ferrocene has been experimentally measured. This effect is explained to be due to cyclopentadiene adsorption. A kinetic model, that takes into account this adsorption, is proposed, which explains the observed experimental results. © 2000 The Electrochemical Society. All rights reserved.
747
Fumitoshi Sakurai, Ken Suto, Junichi Nishizawa, Yutaka Oyama, Mitsutake Motozawa and Yoshinori Hara
A compensated layer with a very low net ionized impurity density was found in ZnSe p‐n homojunctions. We studied these devices by measuring their capacitance‐voltage measurements and with secondary ion mass spectroscopy. The p‐n junctions were prepared with Ga diffusion in p‐type ZnSe bulk single‐crystal substrates or in p‐type liquid‐phase epitaxial layers. The bulk crystals as well as the p‐type epitaxial layers, were grown by the temperature difference method under controlled vapor pressure using Se solvent with
as a dopant. The Ga diffusion profile has a deep tail region with low Ga concentration. The tailing is greatly intensified for samples grown at low Se vapor pressures or without application of Se vapor pressure, although these samples exhibit a blue luminescence. It was found that a thick compensated layer, which lowers the injection efficiency, appeared as a result of this tailing. At higher Se vapor pressures, the compensated layer is not as thick, but the luminescence from self‐activated centers becomes dominant. The compensated layer, as well as Ga tailing region almost disappears when the diffusion time is short even without application of Se vapor pressure. © 2000 The Electrochemical Society. All rights reserved.
751
R. Loo, M. Caymax, M. Libezny, G. Blavier, B. Brijs, L. Geenen and W. Vandervorst
The increased interest in epitaxial
heterostructures for device applications requires very good control of layer thickness and composition. Unfortunately, most of the well‐developed characterization methods, such as Rutherford backscattering spectroscopy (RBS), secondary ion mass spectroscopy, and photoluminescence measurements are unsuitable as production measurement tools. On the other hand, spectroscopic ellipsometry (SE) allows a fast, in‐line, and nondestructive analysis, including wafer mapping capabilities. This paper demonstrates the suitability of SE for the determination of both Ge content and layer thickness of epitaxial
for Ge contents between 1 and 35%. By describing the optical dispersion by means of the harmonic oscillator model, we obtained a clear correlation between the Ge content and
, the resonant energy of the first oscillator, and
, the peak value of the real part of the refractive index. The small spot (30 × 30 μm) size allows one to characterize
layers selectively grown in an isolation structure. The small window size prevents RBS measurements. SE allowed the fine tuning of a selective epitaxial growth process with regard to growth rate, Ge incorporation, and wafer uniformity. © 2000 The Electrochemical Society. All rights reserved.
756
Koji Sueoka, Masanori Akatsuka, Mitsuharu Yonemura, Toshiaki Ono, Eiichi Asayama and Hisashi Katahama
763
D. A. Stocker, I. D. Goepfert, E. F. Schubert, K. S. Boutros and J. M. Redwing
765
Dominic A. Davies, Aron Vecht, Jack Silver, Paul J. Marsh and John A. Rose
A novel method for the synthesis of a wide range of metal sulfides and selenides is described. Polysulfide solutions formed by the dissolution of sulfur in hydrazine monohydrate have been shown to contain the hexasulfide and tetrasulfide anions. The action of these solutions, or their selenium analogues, with a range of transition and main group metal salt solutions yields a precipitate, which after firing at an elevated temperature, forms a crystalline metal sulfide or selenide. This method of preparing metal chalcogenides has been extended to some group II–VI phosphors with promising luminescent properties. © 2000 The Electrochemical Society. All rights reserved.
772
S. J. Laverty and P. D. Maguire
776
E. Llobet, G. Molas, P. Molinàs, J. Calderer, X. Vilanova, J. Brezmes, J. E. Sueiras and X. Correig
780
Roger J. Mortimer and Alison Beech
A planar solid‐state electrochemical carbon monoxide (CO) sensor has been designed, with screen printed electrodes (platinum as the working and counter electrodes, gold as the reference electrode) and a recast film of a sulfonated styrene/ethylene‐butylene/styrene triblock copolymer as the proton conducting solid polymer electrolyte. AC impedance spectroscopy has been found to be a highly sensitive technique for the quantitative characterization of sensor response. A standard equivalent circuit that included the polymer electrolyte and interfacial impedances was employed to fit the ac impedance spectroscopy data in both clean air and in the presence of CO. Chemisorption of CO onto the catalytic platinum electrode surface resulted in a decrease in charge‐transfer resistance with an increase in gas concentration. This change in interfacial impedance was due to a limited amount of CO oxidation occurring due to the polarizing effect of the 10 mV ac amplitude utilized during the ac impedance spectroscopy scan. The sensors did not respond to an atmosphere containing methane, while hydrogen, which readily adsorbs onto the surface of a platinum catalyst, did perturb the ac impedance from the plot obtained in clean air. © 2000 The Electrochemical Society. All rights reserved.
787
Yoshihiro Abe and Masunobu Maeda
792
Ted A O'Brien, Michael C. Zerner, Philip D. Rack and Paul H. Holloway
796
Minoru Nakamura
Influences of concentrations of oxygen and carbon in float zone and Czochralski (CZ)‐grown silicon crystals contaminated with Cu on the photoluminescence (PL) intensities of the 1.014 eV Cu center were measured. Formation of the Cu center was severely hindered by oxygen, but slightly enhanced by carbon. The PL intensities of the center were also influenced by boron and phosphorous for CZ crystals. These findings supported an already published structural model of the center in which the Cu atom was collinearly bonded with Si atoms at the center of the Si‐Si bond. © 2000 The Electrochemical Society. All rights reserved.
799
Y. C. Kang and S. B. Park
The morphology of
phosphor particles was controlled by changing the precursor solution used in the spray pyrolysis. The colloidal and aqueous solutions were obtained using aluminum isopropoxide and aluminum nitrate as the source of aluminum. The characteristics of particles prepared from colloidal solution were compared with those of particles prepared from aqueous solution. The particles prepared from colloidal solution maintained their spherical structure and nonaggregation characteristics of as‐prepared particles even after post‐treatment at 1400°C while aggregation was observed to take place in the particles prepared from aqueous solution. The high thermal stability of particles prepared from colloidal solution was attributed to the stable intermediate,
. For the highest crystallinity and brightness of particles, the optimum post‐treatment temperature was found to be 1200°C. The particles prepared from colloidal solution had higher crystallinity than those prepared from aqueous solution. © 2000 The Electrochemical Society. All rights reserved.