Electrochemical Science and Technology TECHNICAL PAPERS
1851
Hiroyuki Kawamoto
Distributions of the sodium polysulfide composition in the sulfur electrode of the sodium‐sulfur cell and the current density in the cell are investigated using a two‐dimensional and two‐component (ionic and electronic) conduction model. The following points are clarified from the results of calculations and experiments. (i) The polarization of a vertically supported cell at the end of charge starts partially from the upper surface of the solid electrolyte due to the gravitational drop of the sodium polysulfide melt, but the polarization at the end of discharge is axially almost uniform. (ii) A dual mat design of which a porous graphite mat has a high electric resistance adjacent to the electrolyte is preferable for improving the rechargeability. (iii) An oriented mat of which the radial resistivity is smaller than the axial resistivity is able to reduce the cell resistance. (iv) The larger the current density is, the larger the nonuniformity of the melt composition becomes, and the sulfur utilization is reduced by the high current density operation. (v) Voids of the melt at the electrolyte surface accelerate the degradation of the solid electrolyte and reduce the sulfur utilization. (vi) Voids at the metal container side accelerate the corrosion of the metal container.
1861
A. Sasahira, K. Kawamura, M. Shimizu, N. Takada, M. Hongo and T. Yokokawa
Pb2+/Pb0 redox equilibrium was studied with linear sweep voltammetry. The activity of
increases with the solvent basicity. A Pourbaix diagram analogue is presented with redox data obtained from the present and previous studies. The diffusivity of Pb2+ ion was evaluated from the peak currents and the effect of alumina upon it is discussed.
1865
E. Plichta, S. Slane, M. Uchiyama, M. Salomon, D. Chua, W. B. Ebner and H. W. Lin
1869
I. Montera, B. Pelloie, J. Perriére, J. C. Pivin and J. M. Albella
The influence of phosphorus ions incorporated from the electrolyte on the transport process during the anodic oxidation of tantalum has been investigated using nuclear microanalysis and secondary ion mass spectroscopy. The presence of a phosphorus‐rich layer in the oxide gives rise to a partial inversion of the order of the oxygen ions in the film. The results are interpreted by assuming that the oxygen ions directly linked to the phosphorus ions participate in the transport process with a probability of movement lower than the rest of the oxygen ions.
1874
I. S. Hwang, R. G. Ballinger, J. W. Prybylowski and K. Hosoya
A study has been conducted to evaluate the effect of galvanic coupling between precipitated phases, matrix, and near grain boundary chemistries in nickel‐base alloys. Corrosion potential, potentiodynamic polarization behavior, galvanic effects, and passivation kinetics have been determined for grain boundary γ′, Laves phase, and Ni‐Cr‐Fe matrices for a wide range of chromium contents in aqueous systems over the temperature range 30°–288°C. Electrochemical activity of γ′, Laves phase, and sensitized chemistries is significantly higher than the matrix and varies with composition and temperature. Galvanic couples,
, and Laves/matrix in a simulated crack tip environment exhibit higher current density than a sensitized chemistry (6.3 weight percent Cr)/matrix couple. The results of the study show that the electrochemical relationships between grain boundary phases and their couples with the matrix can provide for an extremely local (i.e., at the crack tip) source of anodic and cathodic processes. A correlation between grain boundary
galvanic coupling and environmentally assisted intergranular cracking in alloy X‐750 has been made. At low temperatures, around 100°C, hydrogen embrittlement is proposed as the dominant mechanism. At high temperature it is suggested that both hydrogen embrittlement and stress corrosion cracking are viable mechanisms for crack propagation. A schematic model is presented which describes the relationship between embrittlement mechanisms and local electrochemistry at the crack tip.
1884
S. Menezes, R. Haak, G. Hagen and M. Kendig
1887
U. Bertocci
The possibility of hydrogen discharge at the crack tip during transgranular stress corrosion cracking of Cu‐Au alloys in chloride solutions was examined by modeling electrochemical reactions and transport losses in cracks under steady‐state conditions. To take into account the discontinuous nature of the cracking, which causes periodic minima in the electrode potential at the crack tip, the minimum potential which can be reached was calculated considering the interplay of the various electrode reactions and their spreading along the crack. Kinetic parameters for the redox reactions Fe++/Fe+++and Cu+/Cu++ on gold were measured, in order to provide values for the modeling, which are unavailable in the published literature. The results show that there is no possibility of hydrogen discharge, which rules out hydrogen embrittlement as the cause of the cracking.
1892
S. Nakahara and Y. Okinaka
Scanning and transmission electron microscopes were used to study the effect of cathodic charging of hydrogen on the defect structure of bulk copper foils. Cathodic charging of hydrogen over an extended period of time (∼24h) resulted in a considerable reduction in the ductility of copper foils. This ductility reduction was accompanied by the formation of blisters, dislocations, and hydrogen gas bubbles, and their densities decreased with increasing depth from the foil surface. This observation is similar to the case of hydrogen‐sensitive metals such as iron‐base alloys, and it indicates that copper is embrittled by cathodic charging of hydrogen. In addition, a part of the lost ductility was found to be recoverable by low‐temperature (150°C) annealing. This recovery is attributed to the reduced hydrogen gas pressure resulting from the outdiffusion of molecular hydrogen trapped inside the gas bubbles. This investigation was performed as part of an effort to understand the mechanism of embrittlement of electroless copper deposits used in the manufacture of printed wiring boards.
1896
Akihiko Yoshida and Atsushi Nishino
A novel preparation method for the tantalum‐tantalum oxide‐manganese oxide structure has been found that can be applied to fabrication of solid electrolytic capacitors. In the method, a uniform manganese oxide layer was electrolytically deposited from a bath of an aqueous Mn2+ salt solution on the anodically polarized tantalum oxide dielectric film. During the electrolysis, the dielectric film was irradiated with UV rays, the energy of which is enough to allow the valence electrons to enter the conduction band, so that the manganese oxide can be anodically deposited on the photoexcited tantalum oxide film. The photoexcited anodic oxidation for 15–30 min in the aqueous manganese(II) sulfate solution or manganese(II) acetate solution of pH 3–4 was the preferable condition to obtain a uniform manganese oxide layer. The several capacitor characteristics such as capacitance, tan δ, and leakage current of the formed structure were estimated.
1902
S. J. Ridge, R. E. White, Y. Tsou, R. N. Beaver and G. A. Eisman
Oxygen reduction in a gas‐fed porous electrode attached to a proton exchange membrane is discussed. Experimental data and a mathematical model are presented for the test cell used. Various membrane and electrode assemblies were tested at different levels of platinum loading and Teflon® content. The model accounts for the diffusion and reaction of oxygen and the diffusion and reaction of hydrogen ions. Sulfuric acid was placed above the membrane in the test cell reservoir to provide a source of protons for the reduction of oxygen at the cathode. Based upon model predictions, it is shown that the transport of the protons in the active layer of the cathode is an important factor in the operation of the test cell.
1910
Kan Seto, James Noël, J. Lipkowski, Z. Altounian and R. Reeves
1915
K. Mishra, K. Rajeshwar, Alex Weiss, M. Murley, Robert D. Engelken, Mike Slayton and Hal E. McCloud
A new room‐temperature electrodeposition technique was devised to synthesize
thin films on indium tin oxidecoated glass slides. This technique is based on a nonaqueous ethylene glycol bath containing anhydrous
and elemental sulfur. Three types of electrosyntheses, namely, potentiostatic, galvanostatic, and pulse modes, are discussed and their relative merits compared. A wide variety of characterization techniques were employed to develop a self‐consistent and complementary picture of the morphology, composition, and photoactivity of the
thin films. These included scanning electron microscopy, x‐ray diffractometry, electron probe microanalyses, Auger electron spectroscopy, x‐ray photoelectron spectroscopy, optical analyses, and voltammetry. The photoactivity of these films was evaluated using photoelectrochemical techniques. Finally, the dark and photocorrosion behavior of these films are discussed with the aid of Pourbaix diagrams.
1923
Masakazu Sakaguchi and Masatoshi Ohta
The stability of the three‐phase interface involving the solid catalyst on carbon carrier, liquid electrolyte solution, and fuel gas found in a porous electrode was investigated by means of a radioisotope tracer method for the electrodes prepared from carbon carriers with various fine structures. Higher electrode activity was observed for the electrode prepared with a perovskite‐type
catalyst and a carrier which consisted of a secondary particle crowd due to the aggregation of fine particles. The operating life of the electrode depended remarkably on how much water vapor permeated from the aqueous electrolyte solution into the electrode. The electrode activity decreased abruptly when the permeation of the water vapor exceeded a critical amount. The reactivity of an electrode was found to improve not only by catalytic activity but also by the stabilization of the three‐phase equilibrium in the porous electrode which is promoted by many micropores and a large pore volume formed by the crowd of secondary particles of the carbon carrier.
1927
D. J. Beckstead, D. J. De Smet and J. L. Ord
Ellipsometry has been used to study the formation and electrochromic conversion of Prussian blue films. A Prussian blue film can be deposited on a metal substrate in an appropriate electrolyte by applying a cathodic current. Once grown, a given film can be cycled from its original blue color to a transparent state by applying a cathodic current. The film can also be cycled back to a blue color again with an anodic current; however, the blue film after the first and subsequent cycles has optical properties that differ from the original blue film. At potentials higher than that which return the film to its blue color, the film changes once more, but if the potential is allowed to become too high, the film changes in an irreversible manner.
1933
J. ‐Y. Huot
1939
E. J. Taylor, N. R. K. Vilambi and A. Gelb
We have studied the phenomenology of the catalytic peak for oxygen reduction on the Au(100) surface using cyclic potential voltammetry. In the potential region of this catalytic peak, oxygen is reduced via the overall four‐electron process to hydroxide with a half‐wave potential significantly positive to that of the Au(111), Au(110), and polycrystallite gold surfaces. We have studied the effect of sweep rate, sweep direction, and potential limits on the formation and definition of the catalytic peak. Our data indicate that an “oxidized Au(100)” surface is uniquely catalytic and selective for the overall four‐electron reduction of oxygen to hydroxide. However, the oxygen reduction activity of the “reduced Au(100)” surface is analogous to that of the Au(111) surface. The reduced Au(100) surface promotes the two‐electron reduction of oxygen to peroxide ion, and the half‐wave potential for oxygen reduction is more negative. We conclude that a potential‐induced kinetically limited process is operative during oxygen reduction on oxidized and reduced Au(100) surfaces. Processes consistent with our conclusion are: (i) potential‐induced surface reconstruction between a catalytic and noncatalytic surface and (ii) potential‐induced formation and destruction of a catalytic oxide or hydroxide. Additionally, trace level ionic species other than hydroxide ion could account for the behavior of the oxidized and reduced Au(100) surfaces.
1945
S. Pizzini, N. Buttá, D. Narducci and M. Palladino
1949
J. E. A. M. van den Meerakker and J. H. C. van Vegchel
1954
J. E. A. M. van den Meerakker and J. H. C. van Vegchel
The dissolution of silicon in
solutions with a low
ratio was investigated by etching and electrochemical measurements. Etching is seriously inhibited in comparison to solutions with a high ratio. The electrochemical measurements showed that inhibition is caused by the formation of a mixed valence chromium complex which partly blocks the surface. It has been found that a reaction between intermediates of both the reduction and the oxidation processes plays an important role in etching. A rate law for the etching kinetics is given.
1958
P. Kovács, T. Ando, M. Ishiwatari, Y. Ujihira, E. Kuzmann and A. Vértes
1962
M. C. H. McKubre, S. I. Smedley and F. L. Tanzella
We have carried out a number of experiments to characterize some electrochemical properties of a Na/S cell. They were: measurements of the cell EMF, cell voltage and current on charge and discharge, both at constant current and with stepped currents; cell impedance from 0.5 mHz to 10 kHz; and measurements of the relaxation of the open‐circuit voltage. At the onset of the single‐phase region in the sulfur electrode, the cell impedance from 5 to 0.5 mHz rises to a maximum due to the onset of a diffusion controlled process. The measurements of cell voltage and current confirm this experimental result.
1969
M. C. H. McKubre, S. I. Smedley and F. L. Tanzella
We interpret the impedance results of Part I of the paper in terms of an equivalent circuit composed of three series components: a resistive term and two reactive terms. It is postulated that the higher frequency relaxation (1 kHz to 5 mHz) arises from charge transfer at the β″ alumina interface, the lower frequency, relaxation
from a Warburg impedance in series with the faradaic impedance of the porous carbon fiber electrodes. Voltage relaxation measurements during constant current charge/discharge, as well as at open‐circuit support this interpretation.
1973
Lj. M. Vracar, D. B. Sepa and A. Damjanovic
1977
B. V. Tilak, S. Venkatesh and S. K. Rangarajan
Current‐potential relationships are derived for porous electrode systems following a homogeneous model and when adsorbed intermediates participate in the electrode reaction. Limiting Tafel slopes were deduced and compared with the corresponding behavior on planar electrode systems. The theoretical results showed doubling of Tafel slopes when the slow‐step is a charge‐transfer reaction and a nonlogarithmic current‐voltage behavior when the slow‐step is a chemical reaction. Comparison of the experimental results with theory for the case of oxygen reduction on carbon surfaces in alkaline media indicates that a slow chemical reaction following the initial charge‐transfer reaction to be the likely rate‐controlling step. Theoretical relationships are utilized to determine the exchange current density and the surface coverage by the adsorbed intermediates during the course of oxygen reduction from alkaline solutions on “carbon.” Tafel slope measurements on planar and porous electrodes for the same reaction are suggested as one of the diagnostic criteria for elucidating the mechanistic pathways of electrochemical reactions.
TECHNICAL NOTES
1982
Ronald L. Cook, Robert C. MacDuff and Anthony F. Sammells
1985
O. Teschke and D. M. Soares
1986
Katsuaki Okabayashi, Fumio Goto, Katsushi Abe and Takashi Yoshida
1989
Laszlo Redey
Solid‐State Science and Technology TECHNICAL PAPERS
1992
M. Ghezzo, E. Kaminsky, Y. Nissan‐Cohen, P. Frank and R. Saia
Local oxidation of polysilicon over silicon (LOPOS) isolation has been characterized for use in a 0.8 μm CMOS/BULK process with reduced field oxide edge encroachment (bird's beak). Compared to the standard local oxidation of silicon (LOCOS) LOPOS adds a thin polysilicon layer between the stress relief oxide and the overlying nitride without changing the active area patterning procedure. To optimize the LOPOS structure, the thickness of the oxide and nitride layers was varied in a fully‐factorial experiment, measuring the bird's beak and checking for the presence of silicon edge defects. It was found that for a 6000Å field oxide the bird's beak can be safely reduced to ≈0.3 μm per side with LOPOS, which is significantly less than ≈0.55 μm with LOCOS. The corresponding stack consisted of
. LOPOS fabricated diodes exhibited low leakage of <0.5 nA/cm2 and <0.5 pA/cm for the area and edge components, respectively, while MOS capacitors were breakdown‐free up to 8 MV/cm during voltage‐stress tests, compared to 6 MV/cm for LOCOS.
1997
Chee Burm Shin and Demetre J. Economou
The effect of fluid flow, transport, and reaction on the shape evolution of two‐dimensional cavities during wet chemical etching was studied. Finite element methods were employed to solve for the fluid velocity profiles and for the etchant concentration distribution in cavities of arbitrary shape. A moving boundary scheme was developed to track the shape evolution of the etching cavity. In the case of pure diffusion and under mass‐transfer control, a mask with finite thickness resulted in significantly better etch factor (etch anisotropy) as compared to an infinitely thin mask, albeit the etch rate was essentially unaffected. With fluid flow past the cavity, the etch rate increased fourfold and the etch factor increased by 40% as compared to pure diffusion, under the conditions examined. In addition, the etch rate, etch factor, and cavity wall profiles showed a strong dependence on etch time as the cavity aspect ratio (depth/width) increased with time during etching.
2004
J. H. Thomas III and L. H. Hammer
X‐ray photoelectron spectroscopy has been used to characterize
reactive ion etching residue on the tantalum disilicide surface after removing 100 nm of silicon dioxide. This was done to simulate the structure of multilevel metallization presently being encountered in integrated circuit manufacture. At a pressure of 80 millitorr and a power density of 1 W/cm2, the residue layer formed consists chemically of a mixed tantalum and silicon fluoride and oxide‐like film. This layer is complex and does not appear to contain polymeric fluorocarbon as has been observed on silicon at slightly higher hydrogen concentrations in the glow discharge. Its thickness is estimated to be 3 nm based on electron escape depths. The presence of
causes the surface residue layer to be more oxygen rich in comparison with the uncoated tantalum disilicide surface. Sputtering does occur at a self‐bias of 300V and results in preferentially removing silicon. Core‐level binding energies are reported for tantalum disilicide, the etch residue, the native oxide on the disilicide, and some related materials for reference purposes.
2010
P. C. Murley and G. R. Srinivasan
A detailed phenomenological model is presented for the growth rate dependence of arsenic autodoping profiles in silicon. The model was inferred from numerical simulation of arsenic diffusion during epi prebake and growth stages. Simultaneously simulated were a region with a buried layer and a separate region with no buried layer. The model employs a two‐state adsorbed layer on the silicon surface and a set of kinetic coefficients which enable the modeling of measured lateral peak concentrations, doses, and epi gradients. The model has been implemented in a pseudo two‐dimensional modification of the SUPREM program.
2015
A. Baghdadi, W. M. Bullis, M. C. Croarkin, Yue‐zhen Li, R. I. Scace, R. W. Series, P. Stallhofer and M. Watanabe
We report an international interlaboratory dual experiment to determine the calibration factor used to calculate the interstitial oxygen content of silicon from room‐temperature (300 K) infrared (IR) absorption measurements. We conducted round robins for both the infrared and the absolute measurements on the same or equivalent specimens. The calibration factor for computing the oxygen content of silicon in parts per million atomic (ppma) from a room‐temperature measurement of the absorption coefficient at 1107 cm−1 was determined to be
. The IR round robin showed a reproducibility on the order of 3%.
2025
F. Schomann and K. Graff
In order to achieve a high multilaboratory precision in measuring the oxygen content in CZ silicon slices and wafers by means of IR absorption spectroscopy various deviations from ideal measurement conditions are discussed and correction methods are presented. The main sources for measurement errors exceeding ± 1% standard deviation are: the radiation scattering at rough wafer reverse sides, the sample temperature during the measurement, the free carrier absorption if the carrier concentration exceeds 1015 cm−3, and the residual oxygen concentration in the reference sample if this consists of a common FZ silicon material. Less important are thickness deviations between sample and reference, spectral resolution, and instrumental errors for modern spectrometers. After applying all corrections, a multilaboratory precision in dispersive spectrometers of
is expected for both sides polished 2 mm thick silicon slices and one‐side polished silicon wafers, respectively.
2032
S. Suto, N. Hayasaka, H. Okano and Y. Horiike
2035
C. A. Paz de Araujo, Y. P. Huang and R. Gallegos
A method for selective oxidation using ultrathin nitrogen‐rich layers (<20Å) grown by rapid thermal processing is presented. Oxidation inhibition in these layers is shown to be a function of the previous oxide layer thickness and the
reaction conditions during the rapid thermal nitridation cycle. The oxide growth inhibition property of these layers is tested for rapid thermal and furnace grown oxides. Since oxide growth inhibition appears to be a strong function of the initial oxide thickness, the rapid thermal nitridation process is more controllable than conventional furnace methods because of the shorter exposure time to oxygen contamination. Characterization of the nitridation reaction, the influence of the initial oxide thickness, and the localized inhibition phenomenon are presented with the aim of making this technique useful for novel VLSI structures.
2038
Andrew Yeckel, Stanley Middleman and Arthur K. Hochberg
A mathematical model that provides a unified treatment of growth of LPCVD films from silane mixtures is in agreement with experimental results from several investigators. The effects of pressure, flow rate, and reactor geometry on within‐wafer and wafer‐to‐wafer uniformity are predicted by the model. Numerical simulations of the effect of wafer boat and cage design on the uniformity of growth are presented. It is shown that for a crossflow reactor, in which the gases flow parallel to the wafer surfaces, convection makes a negligible contribution to the transport of species. The role of homogeneous reactions in the growth of in situ doped polysilicon, silicon dioxide, and SIPOS films is discussed with reference to model results.
2050
G. S. Oehrlein, S. W. Robey, J. L. Lindström, K. K. Chan, M. A. Jaso and G. J. Scilla
A review of in situ x‐ray photoelectron spectroscopy studies of fluorine‐based plasma etching induced surface modifications of several electronic materials, but primarily single‐crystal silicon, is presented. Post‐plasma surface analysis of vacuum‐transferred etched specimens has been conducted in an ultra‐high vacuum surface analysis chamber connected via a load‐lock to the etching chamber. The achievement of
etch selectivity because of different formation rates of a passivating fluorocarbon film which controls the etching behavior and in general the substrate dependence of the fluorocarbon film formation rate is discussed. The post‐plasma in situ surface analysis methodology has been extended to the study of realistic semiconductor microstructures after reactive ion etching. Spatially resolved in situ x‐ray photoemission spectroscopy of the surface chemistry of a photoresist‐patterned silicon dioxide on silicon contact hole etching process has been undertaken by utilizing the topography and conduction characteristics of the realistic microstructure. Often, dry etching processes are followed by a cleaning treatment in order to prepare device quality surface conditions. The dependence of the efficiency of conventional oxygen plasma/wet oxide removal cleaning treatments of reactive ion etched (RIE) silicon surfaces on RIE operating conditions has been studied. The composition and extent of reacted surface layers, e.g., the competitive formation of fluorides or oxides in
discharges, have also been reviewed in the present article.
2058
Y. Shimanuki, H. Furuya and I. Suzuki
The effect of carbon on the nucleation of the oxygen precipitates in CZ silicon crystals is investigated. Crystals doped with carbon are grown and the thermal history in the cyrstal puller is varied to a large extent from one part of the crystal to another. Annealing of specimens cut from these crystals reveals that the oxygen precipitation is enhanced by carbon atoms in a concentration range of 1015–1016 cm−3. It is shown that a variation of the carbon concentration within this range does not essentially alter the nucleation mechanism of the oxygen precipitates. It is also clarified that the carbon atoms play an important role in the transformation of the forerunners of the nuclei into the active nuclei. A model of the nucleation process of the oxygen precipitates is discussed in some detail.
2063
J. P. Gambino, M. D. Monkowski, P. J. Tsang, J. F. Shepard, C. M. Ransom and C. Y. Wong
2067
S. P. DenBaars, B. Y. Maa, P. D. Dapkus and A. Melas
2070
S. V. Hattangady, G. G. Fountain, D. J. Vitkavage, R. A. Rudder and R. J. Markunas
2073
S. Coffa, L. Calcagno, S. U. Campisano, G. Calleri and G. Ferla
Silicon wafer and devices have been implanted with gold ions and thermally processed in the 1073–1243 K temperature range. Resistivity profiles, leakage currents in p‐n junctions, and recombination lifetime have been measured as a function of the Au‐implanted dose, annealing temperature, and time. The use of ion implantation for the predeposition of the Au atoms allows a good control of the lifetime in a rather wide range of values. In addition, it is shown that it is very easy to generate flat gold profiles across the silicon wafers.
2076
Y. ‐C. Simon Yu and Vladimir F. Drobny
2082
Junichiro Mizusaki, Junji Tabuchi, Takashi Matsuura, Shigeru Yamauchi and Kazuo Fueki
2088
H. Nagamoto and H. Inoue
2093
S. Nariki, S. Ito, K. Uchinokura and N. Yoneda
The ionic conductivities of mixed alkali (K+, M+)‐β‐ferrites (M+: Na+, Rb+, Cs+, and Tl+) with different compositions of K+/M+ were measured. The mixed alkali effect was found in K‐Na, K‐Rb, and K‐Cs systems, that is, the minimum in conductivity and the maximum in activation energy. However, no effect was observed in the K‐Tl system. The excess free energy of mixing
was calculated from the activity coefficients of each ion in the mixed alkali β‐ferrite, which were obtained by the ion exchange equilibrium between (K+, M+)‐β‐ferrite and
melt. The
values had large negative values in K‐Na and K‐Cs systems, while that in K‐Tl system was almost zero. The degree of the mixed alkali effect was correlated with the magnitude of the
.
2099
Klaus Hilpert
A large number of gaseous complexes composed of metal fluorides and metal chlorides have been identified and investigated so far. The data are summarized in various reviews. Our knowledge of the gaseous homo‐ and hetero‐complexes of metal bromides and metal iodides is less than that of the corresponding fluoride and chloride complexes although they are of considerable practical interest for metal halide lamps. A survey of the review articles on gas‐phase complexation and on the various methods used for its investigation is given. By far the most complete information was obtained by the method of Knudsen effusion mass spectrometry. The potential of this method is described with respect to its use for the study of complexation in metal halide lamps. An account of the gaseous homo‐ and hetero‐complexes observed in metal iodide and metal bromide vapors is given. The enthalpy and entropy changes as well as the equilibrium constants determined for the dissociation reactions of the complexes are summarized and discussed. The equations for the partial pressures of the various complexes are tabulated. The data are discussed with respect to their practical significance for metal halide lamps.
2108
Pei‐Ing Lee, John Cronin and Carter Kaanta
Blanket‐deposited CVD W has been developed and implemented in a 4‐Mbit DRAM and equivalent submicron VLSI technologies. CVD W was applied as contact stud, interconnect, and interlevel via stud. The technologies have been proven reliable under several reliability stress conditions. Major technical problems involved in CVD W processing, such as adhesion, contact resistance, etchability, and hole fill will be discussed. A novel technique that uses
as a contact and adhesion layer will be presented. This technique has lead to the resolution of the above technical problems and significantly improved the manufacturability of blanket CVD W processes.
2113
J. R. Cavins, Y. K. Yeo and R. L. Hengehold
Both photoluminescence (PL) and selective pair luminescence (SPL) measurements have been made on various
substrates and vapor‐phase epitaxial (VPE) layers of
as a function of pump laser energy, excitation laser intensity, and sample temperature. Comparison of the results shows that in lesser quality substrates, the SPL technique is significantly superior to the PL method in that it can provide an unambiguous impurity identification far better than that available from the PL method. However, since the structure of SPL spectra strongly depends upon the laser excitation energy, the SPL signals should be optimized with a proper pump laser energy for particular acceptors. Various residual acceptors in semi‐insulating and VPE
substrates such as C, Mg, Zn, Si,and Ge have been identified through the SPL method, and energy values of their excited states are reported here.
2119
B. Smets, J. Rutten, G. Hoeks and J. Verlijsdonk
2123
Masamichi Ippommatsu and Hirokazu Sasaki
TECHNICAL NOTE
2128
L. Brixner, M. K. Crawford and G. Hyatt
ACCELERATED BRIEF COMMUNICATIONS
2131
My T. NguyÊn and LÊ H. Dao