Batteries, Fuel, Cells, and Energy Conversion
A263
P. Suresh, A. K. Shukla and N. Munichandraiah
A267
Olga A. Baturina and Gary E. Wnek
Electrospraying of
-Nafion-alcohol dispersions was employed as a new method to deposit catalyst layers on Nafion membranes for hydrogen/oxygen(air) fuel cells. It is shown that single cells with catalyst layers obtained by electrospraying exhibit good initial performance
at 80°C and 300 kPa without the need for hot-pressing of the electrode layer. Analysis of polarization losses reveals a significant contribution of mass-transport losses to the fuel cell performance for hydrogen/air fuel cells. We suggest that control of electrospray processing parameters can lead to tailored electrode structures where such mass transport losses are mitigated.
A270
S. Imaizumi, K. Shimanoe, Y. Teraoka and N. Yamazoe
Reverse homogeneous precipitation using a chelating compound was applied to obtain ultrafine small particles of perovskite-type oxides dispersed on a carbon support. The mixed hydroxides with 7.3 nm mean particle size were supported on carbon powders, and the resulting carbon-supported precursors were converted to fine oxides by calcining in a
atmosphere. The optimal loadings of the particles on carbon under oxygen reduction conditions were tested, and it was found that the electrodes prepared by reverse homogeneous precipitation using the chelating compound showed surprisingly high performances for the small amounts of loading that were used.
A273
Carl A. Reiser, Lawrence Bregoli, Timothy W. Patterson, Jung S. Yi, J. Deliang Yang, Mike L. Perry and Thomas D. Jarvi
A mechanism that may cause accelerated performance decay of fuel cells is presented. The mechanism is explained using a one-dimensional model of the potential profile. The analysis indicates that the electrolyte potential drops from 0 to
(vs. RHE) when the anode is partially exposed to hydrogen and partially exposed to oxygen. This causes flow of current opposite to normal fuel cell mode at the oxygen-exposed region and raises the cathode interfacial potential difference to 1.44 V, causing carbon corrosion, which decreases performance. The decay mechanism was validated using two different experimental setups which reproduced the carbon-corrosion phenomenon.
A277
Hee-Sang Shim, Hyo-Jin Ahn, Tae-Yeon Seong and Kyung-Won Park
We have investigated the electrochromic properties of nickel oxide as a function of methanol concentration. It is shown that the transmittance of the aged nickel oxide monotonically increases with increasing methanol concentration over a wide range of 0.1-5 molar in a liquid solution for a direct methanol fuel cell. It is demonstrated that the methanol concentration can be visualized by means of the electrochromic properties of the aged nickel oxide.
A279
Hongpeng He, Raymond J. Gorte and John M. Vohs
A281
Kazuhiro Teranishi, Shohji Tsushima and Shuichiro Hirai
We used magnetic resonance imaging (MRI) to examine the distribution of the water content in a polymer electrolyte membrane within an operating fuel cell. Of the three thicknesses studied, the thinner membranes were less hydrated than the thickest membrane. In addition, the total water content in the membranes decreased with an increase in the cell current. We also used electrochemical impedance spectroscopy to check the MRI results and found that the spectroscopy results agreed with the imaging results.
A285
J. Barker, R. K.B. Gover, P. Burns and A. Bryan
A288
M. Abbate, S. M. Lala, L. A. Montoro and J. M. Rosolen
A291
Robert Larsen, Joseph Zakzeski and Richard I. Masel
Direct formic acid fuel cells have been demonstrated as a viable power source, particularly for portable power applications. Palladium catalysts are quite active, but the activity of pure palladium nanoparticles decays slowly with time. In this paper, we examine the properties of palladium on various supports to see if the activity can be stabilized. It is found that catalytic films made by depositing a submonolayer of Pd on V, Mo, W, and Au foils show activity that is stable. Pd-V outperforms conventional
catalyst at
vs. RHE by three orders of magnitude on a per mass precious metals basis, and by two orders of magnitude on a per exposed surface area basis. Evidently, palladium films on supports have unusual properties for formic acid electro-oxidation.
A294
V. Prakash Reddy, Marshall C. Smart, Keith B. Chin, Bugga V. Ratnakumar, Subbarao Surampudi, Jinbo Hu, Ping Yan and G. K. Surya Prakash
The ion-solvent and ion-ion interactions, oxidative electrochemical stabilities, and ionic mobilities of a series of lithium salt electrolytes with commonly used electrolyte solvents, propylene carbonate (PC) and dimethyl carbonate (DMC), have been studied using
nuclear magnetric resonance (NMR) spectroscopy, cyclic voltammetry (CV), and ionic conductivity measurements. The coordinating ability of PC toward lithium salts is significantly higher than that of DMC as shown by the relatively large deshielding of the carbonyl carbon of PC over that of DMC. We have also prepared a novel electrolyte, lithium tetrakis(trifluoromethanesulfonato)gallate
, and investigated its relative binding to PC by
NMR spectroscopy. The latter salt showed significant deshielding of the carbonyl carbon of PC compared to the other salts studied, including the conventional
. However, its conductivity is not enhanced to the same extent and is comparable to that of
. The CVs show their relative stabilities toward oxidation around
and reduction close to lithium potentials. All electrolytes studied here have good electrochemical stability from
vs.
, and are suitable for applications in lithium-ion cells.
A299
Sang-Mok Park, Tae-Hyung Cho, You-Mee Kim and Masaki Yoshio
A303
J. Arrebola, A. Caballero, L. Hernán, J. Morales and E. Rodríguez Castellón
The effect of coating the nanometric spinel
with Ag on its rate capability was studied. The X-ray photoelectron spectroscopy (XPS) concentration depth profiles obtained reveal that the intensity of the Ag 3d peak remains unchanged for a long sputtering time, so the spinel particles do not seem to be coated by an Ag layer. The effect is detrimental at high charge/discharge rates and the addition of silver significantly degrades the rate capability of the spinel. Ag oxide nanoclusters formed in the first charge process possibly establish a barrier that hinders transfer of the high ion flux between the electrolyte and electrode.
A308
V. Ganesh, V. Lakshminarayanan and S. Pitchumani
A313
Zhiqiang Xu, Zhigang Qi and Arthur Kaufman
Sulfonic acid groups have been successfully linked onto carbon particles supporting a catalyst by decomposing
in the presence of the supported catalyst. Electrodes made using such sulfonated catalysts need less Nafion in the catalyst layer and perform much better than those made using the unsulfonated counterpart.
A316
Junrong Li, Zilong Tang and Zhongtai Zhang
A320
Jingrong Yu, Md Nazrul Islam, Toyoaki Matsuura, Masayuki Tamano, Yoshihiko Hayashi and Michio Hori
To improve the performance of a proton exchange membrane fuel cell (PEMFC), a more porous electrode was successfully prepared with a nonprocessed Ketjenblack EC-600JD carbon black as the material of the micro porous layer (MPL) in comparison with Vulcan XC-72R. Cyclic voltammograms showed a 49.3% increase in the Pt utilization for the more porous electrode over that with Vulcan XC-72R. An improvement in cell performance was also observed for the more porous electrode, which is attributed to increased Pt utilization and improved mass transport. Furthermore, the durability test of the cell demonstrated nondecay performance after
operation.
A324
M. A. Navarra, S. Panero and B. Scrosati
We report a preliminary study on novel protonic membranes, obtained by the gelification of a selected polymer matrix in a highly stable ionic liquid solvent, i.e., 1,2-dimethyl-3-
-propylimidazolium bis(trifluoromethylsulfonyl)imide (DMPI-Im). The addition of an acid, chemically compatible with the ionic liquid thanks to the equality between the anionic components, gives rise to a reasonably high conductivity which, together with the good mechanical and thermal stability as well as an excellent control on the methanol crossover rate, make the membranes of interest for practical applications.
A328
Attila Palencsár and Daniel A. Scherson
Corrosion, Passivation, and Anodic Films
B21
A. Davoodi, J. Pan, C. Leygraf and S. Norgren
Scanning electrochemical microscopy (SECM) has been integrated with electrochemical atomic force microscopy (EC-AFM), and applied for in situ studies of localized corrosion of Al alloys in NaCl solution. The instrument utilizes a dual mode probe, which functions both as a normal cantilever and as an ultramicroelectrode. The
redox mediator was used for mapping of local electrochemical current. Concurrent topography and electrochemical activity maps have been obtained on the same surface area with micrometer lateral resolution. Preliminary results show ongoing localized dissolution related to intermetallic particles in the Al alloys, which may occur well below the breakdown potential.
Electromechanical/Chemical Deposition and Etching
C81
Jaeho Oh, Yongsug Tak and Jaeyoung Lee
Dielectric Science and Materials
F17
Jeon-Ho Kim, Soon-Gil Yoon, Seung-Jin Yeom, Hyun-Kyung Woo, Deok-Sin Kil, Jae-Sung Roh and Hyun-Chul Sohn
Semiconductor Devices, Materials, and Processing
G135
Seung-Chul Lee, Jin-Cherl Her, Sang-Myeon Han, Kwang-Seok Seo and Min-Koo Han
G137
Y. L. Chueh, L. J. Chou, S. L. Cheng, J. H. He, W. W. Wu and L. J. Chen
G140
D. K. Hwang, Ji Hoon Park, Jiyoul Lee, Jeong-M. Choi, Jae Hoon Kim, Eugene Kim and Seongil Im
G143
An-Thung Cho, Jia-Min Shieh, Jiann Shieh, Yi-Fan Lai, Bau-Tong Dai, Fu-Ming Pan, Hao-Chung Kuo, Yong-Chang Lin, Kuei-Jung Chao and Pang-Hung Liu
Three-dimensional Si (Ge) nanocrystals (NCs) were dispersed within the nanopores of mesoporous silica films by high-density plasma (HDP), low-density plasma, or implantation. Surface states of the resulting Si (Ge) NCs∕silica arrays initiate blue-white photoluminescence (PL). HDP makes reactive species highly mobile and enables deposited NCs bonded with pore-wall well, therefore, efficiently constructing photoemission arrays. The mean density of HDP-synthesized semiconducting NCs is as high as
. Accordingly, blue PL of arrays obtained with HDP, which is 4-7 times stronger than those obtained with other methods, exhibits quantum-efficiency of 1%, near the reported value for green-to-red light emission from quantum-confined Si NCs.
G147
C. S. Tan and R. Reif
Using copper wafer bonding and silicon substrate thinning, a novel face-to-face silicon bilayer stacking method was successfully demonstrated. Silicon-on-insulator donor wafer was bonded to a substrate wafer using low temperature Cu wafer bonding. Donor wafer was ground and etched back to the buried oxide layer in selective tetraethylammonium hydroxide solution. It was also possible to thin the silicon substrate using hydrogen-induced layer splitting. A progression to silicon multilayer stack was also demonstrated. Cross-sectional scanning electron microscopy confirmed this type of silicon layers transfer and stacking. This method can potentially be used in three-dimensional integration.
G150
Dong-Seok Leem, Jeong-Tae Maeng, Dae-Yong Lee and Tae-Yeon Seong
Sensors and Displays: Principles, Materials, and Processing
H49
Weizhen Xiong and Girish M. Kale
General Topics
J13
Kazuhiro Kaneda, Mineo Ikematsu, Yurika Koizumi, Haruki Minoshima, Tsuyoshi Rakuma, Daizo Takaoka and Masashi Yasuda
The characteristics of a new-type of ozone-generating electrode with a catalyst layer fabricated by thermal decomposition were investigated. The catalyst layer consisted of insulating tantalum oxide and metallic platinum. Ozone generation was observed when the concentration of Ta of the catalyst layer was 70% and above and the maximum current efficiency of ozone generation was 6%. Scanning electron microscopy revealed cracks, which were capable of ozone generation, reaching the Pt buffered layer of the electrode. It is concluded that the cracks were the paths of the electrolyte and that electronic transfer was accomplished on the surface of the buffered layer.