The Electrochemical Society was founded in 1902 to advance the theory and practice at the forefront of electrochemical and solid state science and technology, and allied subjects.
Find out more about ECS publications
Visit the ECS homepage
Number 4, January 2000
Previous issueNext issue
Open all abstracts, in this issue
Ping Liu, Ji‐Guang Zhang, C. Edwin Tracy and John A. Turner
Porous vanadium oxide materials were prepared by electrochemical deposition in the presence of surfactants. Both scanning electron microscopy and ac impedance results indicated a large increase in surface area compared with a sample prepared without surfactants. X‐ray diffraction and infrared spectroscopy results indicated that despite the difference in surface area these materials have similar structures. The vanadium oxide electrode prepared in the presence of surfactants showed improved rate performance when used as a cathode in lithium batteries, with a capacity of 220 mAh/g at a 5C rate. ©2000 The Electrochemical Society
Jim Y. Lee, Ruifen Zhang and Zhaolin Liu
SnO‐graphite composites containing up to 30 wt% of SnO were prepared by slow hydrolysis of SnCl2 in the presence of graphite powders. Best application performance was delivered by a composite containing 13.6 wt% of SnO, of which the specific capacity is 450 mAh/g at the C/6 rate and decreases by 12% after 30 cycles. This is a substantial improvement over unsupported SnO which, despite a larger initial capacity (870 mAh/g theoretical), would lose 52% of the capacity in the same number of cycles. In our opinion, the ductility and conductivity of the graphite matrix, a high dispersion of the SnO phase, and the presence of Li2O barrier layers formed in the first electrochemical decomposition reaction of SnO, work in unison to stabilize Sn microparticles against agglomeration, the established cause of application problems in tin composite oxide based anode materials. ©2000 The Electrochemical Society
Miran Gaberscek, Marjan Bele, Jernej Drofenik, Robert Dominko and Stane Pejovnik
A novel approach to reduce irreversible Li loss due to carbon anode passivation is described. The graphite particles for use as anode material are pretreated in an aqueous solution of a polyelectrolyte. The polyelectrolyte (gelatin) molecules adsorb onto the particle surface and have a significant impact on anode passivation, as well as on the binding properties of the carbon particles, i.e., gelatin also serves as a particle binder. The reversible capacity of pretreated electrodes is similar to the reversible capacity of conventional electrodes, but the irreversible capacity losses are much smaller and limited to the first charge/discharge cycle. ©2000 The Electrochemical Society
F. Ronci, B. Scrosati, V. Rossi Albertini and P. Perfetti
The application of the energy dispersive X‐ray diffraction (EDXD) technique to in situ structural measurements on battery materials is shown for the first time. EDXD may present a promising alternative for this kind of measurement to the traditional diffractometric technique, even when the synchrotron radiation is used. The merits and drawbacks of this method are discussed, with particular attention to the solution of the X‐ray absorption problem that, reducing the signal intensity, imposes the use of specifically designed cells. Finally, preliminary results obtained in the study of a typical commercial cathodic material for Li‐ion batteries (i.e.,LiNi0.8Co0.2O2) are reported. ©2000 The Electrochemical Society
K. Amine, H. Yasuda and M. Yamachi
Reversible extraction and insertion of lithium from and into olivine LiCoPO4 at 4.8V vs. lithium have shown that this material is a good candidate for a high‐voltage lithium‐ion battery. Electrochemical extraction was limited to 0.42 lithium per formula unit, with a charge capacity of 86 mAh/g and a discharge capacity of 70 mAh/g. In this case. the material retains its structural integrity with a slight contraction of the unit cell upon cycling. The crystallinity of the electrode during charge and discharge processes was not affected, as deduced from the sharpness of the X‐ray diffraction peaks of the cycled cathode material. ©2000 The Electrochemical Society
Z. Dai X., D.‐H. Wang, J.‐Y. Zou and Y.‐H. Zhou
A “green” route was used for the preparation of lead‐acid battery electrodes from PbCO3. Powder microelectrodes and paste electrodes prepared from PbCO3 were investigated. Results showed that the performances of PbSO4/Pb and PbO2/PbSO4 powder microelectrodes made from PbCO3 were as good as those made from PbO. The positive paste electrode utilization reached 74.4% when discharged at 2.0 mA/cm2, and negative electrode utilization was more than 90% at the same discharge current density. Thus, this green route to produce PbCO3‐type lead‐acid battery electrodes could be used. ©2000 The Electrochemical Society
J. Hayon, A. Bettelheim, C. Yarnitzky and J. Yahalom
The behavior of copper in borate buffer solution (pH 7) in the presence of the surfactant dodecylsulfate was studied using cyclic polarization, the electrochemical quartz crystal microbalance technique, and scanning electron microscopy. The results indicate absorption of dodecylsulfate causing severe pitting of the copper surface. The pitting potential (Ep) in the presence of 1000 ppm (3.5×10−3M) surfactant is 0.04V (vs. a standard calomel electrode) and it varies with the dodecylsulfate ion (DS−) concentration: Ep (V)=−0.123log[DS−]−0.268. It is postulated that the formation of the complex Cu(DS)2 is involved in the pitting mechanism. ©2000 The Electrochemical Society
Seong‐Deok Ahn, Hyun‐Bae Lee and Sang‐Won Kang
Surface morphology of aluminum thin films grown by metallorganic chemical vapor deposition has been improved by growing aluminum/titanium nitride multilayers. When the aluminum films were deposited continuously, the reflectance vs. deposition thickness curves showed a maximum reflectance at the completion of coalescence of islands, and then showed a gradual decay with increasing aluminum thickness because of nonuniform grain growth. By inserting 1 nm titanium nitride layer grown by atomic layer deposition on aluminum layer at the maximum reflectance, the reflectance was recovered again to the peak reflectance like a sinusoid waveform. Therefore, without considerable loss of electrical conductivity surface smoothness of aluminum films has been able to be achieved by repeating the aluminum/titanium nitride multilayer depositions. ©2000 The Electrochemical Society
Noriyuki Sonoyama, Satoshi Shiozaki, Prasad Manjusri Sirimanne and Tadayoshi Sakata
Formation of CuInS2 by modifying the In2S3 surface was attempted by solution incorporation reaction. An In2S3/In2O3 pellet was dipped in a solution containing copper(I) chloride and hydroxyl ammonium chloride at 95°C for 10 s. The X‐ray diffraction pattern and diffuse reflectance spectra changed by the chemical treatment indicated formation of a CuInS2 thin film on the surface of In2S3. The dark and photocurrent voltage curves measured in the poly‐sulfide solution demonstrated the thin film on the surface of In2S3 is a p‐type semiconductor. By annealing at 400°C, the semiconductor type was changed from p to n. ©2000 The Electrochemical Society
H. Nguyen Cong, K. El Abbassi and P. Chartier
Experiments have shown the feasibility of new composite electrodes ECP(Ox) resulting from the dispersion of nanoparticles of a metal oxide (Ox) into an electrically conductive polymer (ECP). In this preliminary work, Ox was a spinel mixed valence oxide of copper and manganese, Cu1.4Mn1.6O4, and ECP was polypyrrole. The intimate mixing of the two materials modified neither the ECP charge‐transfer and transport behavior nor the electrocatalytical activity of the oxide. These composite electrodes exhibited a remarkable stability, even in acidic media, in contrast to noncomposite electrodes of the same oxide. ©2000 The Electrochemical Society
P. N. K. Deenapanray, H. H. Tan, L. Fu and C. Jagadish
Plasma‐enhanced chemical vapor deposition of SiO2 at temperatures below 300°C was used in conjunction with rapid thermal annealing for quantum well intermixing. Variable blue shifts of up to ∼200 meV were observed while still maintaining clearly resolved exitonic behavior. The energy shifts were similar for capping layers deposited below 200°C, which were significantly higher than those obtained for SiO2 layers deposited at 300°C. We demonstrate that the increased porosity of SiO2 capping layers deposited below 200°C is responsible for the enhanced intermixing. The evidence for porosity‐enhanced intermixing was obtained from spectroscopic ellipsometry, Fourier transform infrared spectroscopy, and P‐etch rate measurements. ©2000 The Electrochemical Society
Taiju Tsuboi
The decay of the AT emission band by Pb2+ ion has been investigated in KBr and KCl crystals using a streak camera. Unlike the previously obtained triexponential decay curve, a multiexponential‐like decay curve has been observed in the measurement at various streak sweep times between 20 ns and 10 μs. It is suggested that the nonexponential decay indicates distribution of Pb2+ ions with different site symmetries. ©2000 The Electrochemical Society