Batteries and Energy Storage
A161
Liu Zhou, Wentao Li, Mengqing Xu and Brett Lucht
Lithium difluoro(oxalato) borate (LiDFOB) is a promising alternative lithium salt for lithium ion battery electrolytes. The ligand exchange reaction of LiDFOB to generate Lithium tetrafluoroborate (LiBF4) and lithium bis(oxalato)borate (LiBOB) was investigated by Nuclear Magnetic Resonance (NMR) spectroscopy. A thermally induced equilibrium exists between LiDFOB, LiBF4 and LiBOB. The activation barrier for conversion of LiDFOB to LiBF4 and LiBOB is 137 KJ mol−1 and the equilibrium favors LiDOFB by 14 KJ mol−1.
A165
Masaki Yamagata, Kazunari Soeda, Shigeaki Yamazaki and Masashi Ishikawa
Non-aqueous gel electrolytes based on an alginate (Alg) and 1-ethyl-3-methylimidazolim tetrafluoroborate (EMImBF4) are prepared for electric double layer capacitors (EDLCs). The transparent colorless gel sheet has the high levels of mechanical strength and retentivity of ionic liquid needed to construct EDLC cells. According to charge/discharge measurements, a model EDLC cell with an Alg/EMImBF4 gel shows high discharge capacitance in spite of using a gel-state electrolyte, implying that high affinity of alginate for an activated carbon electrode leads to a decrease in the electrode/electrolyte interfacial resistance. A test cell with Alg/EMImBF4 maintains its coulombic efficiency over 99.8% during 5,000 cycles.
Fuel Cells and Energy Conversion
B121
Weida Shen, Ajay K. Prasad and Joshua L. Hertz
Water management remains a major issue for polymer electrolyte-based fuel cells. This letter presents a novel hybrid polymer fuel cell that prevents flooding. A proton exchange membrane (PEM) and an anion exchange membrane (AEM) are placed on opposite sides of a porous, hydrophilic layer in which the product water is formed and then shunted to the exterior of the fuel cell. Maximum power output during these initial tests was 8 mW/cm2 at 30°C, somewhat less than comparable PEM and AEM fuel cells. Though the design is promising, potentiostatic tests at 70°C indicate that maintaining hydration may be a concern.
B124
Jae-Min Lee, Sun Jin Yun, Jun Kwan Kim and Jung Wook Lim
Texturing of Ga-doped ZnO (GZO) was performed for Si thin film solar cell applications using the acetic acid-diluted nitric acid solution. The nitric acid-based texturing solution resulted in rougher surface morphology than the HCl solution that has been generally used as a texturing solution of ZnO-based transparent conductive oxides. The highest solar cell conversion efficiency was achieved using 400 nm-etched GZO film. The short circuit current density and conversion efficiency of the single junction a-Si:H solar cell were improved considerably by as much as 28 and 42%, respectively, compared to those of reference cells.
Corrosion, Passivation, and Anodic Films
C21
W. C. Kim, N. D. Nam, J. G. Kim and J. I. Lee
The corrosion properties of AZ91 and its alloy with 0.33 wt.% strontium were investigated in a 200 ppm Cl− solution. The microstructures of the alloys were examined by X-ray diffraction and electron probe X-ray microanalysis. Potentiodynamic polarization and electrochemical impedance spectroscopy were used to evaluate the corrosion resistance of the alloys. AZ91 with 0.33 wt.% Sr addition showed better corrosion resistance than AZ91 due to the increase of second phases (Mg2Sr, Al4Sr, and AlSr compounds) at the grain boundary, refined grain size and more continuously dispersed β phase.
Electrochemical/Chemical Deposition and Etching
D103
Sunjung Kim, Kye-Sun Park and Soo-Hyun Kim
Cu nanowires are directly patterned on W diffusion barrier surface by electrodeposition without using any template. Prior to Cu nanowire growth, a photoresist (PR) film coated over the W surface was mechanically patterned in a random manner with atomic force microscope (AFM) tip. Polycrystalline Cu nanowires in the shape of beaded string were electrochemically formed along line patterns on the W surface. This new approach of Cu nanowire synthesis suggests the feasibility of fabricating Cu interconnects for Si-based electronic devices by direct Cu nanowire patterning.
Electrochemical Synthesis and Engineering
E35
Si Joon Kim, Doo Hyun Yoon, You Seung Rim and Hyun Jae Kim
A solution-processed ZrO2 gate insulator was fabricated using high-pressure annealing (HPA). The dehydroxylation process was accelerated and a thin, dense ZrO2 film was formed at a low annealing temperature of 350°C using HPA. This resulted in superior dielectric strength of the ZrO2 films (about 10−9 A/cm2 at 2 MV/cm) for use as gate insulators. A low-temperature solution-processed InZnO thin-film transistor with such a ZrO2 gate insulator had a saturation mobility of 0.10 cm2/V·s and an on/off ratio of 1.17 × 104.
E38
Kohsei Takahashi, Rong-Jun Xie and Naoto Hirosaki
β-sialon (Si6−zAlzOzN8−z):Eu2+ phosphors with the oxygen concentrations as low as less than 1 wt% were synthesized by using the pure Si metal as the Si source. The oxygen concentrations could be controlled in the range of 0.3–0.7 wt%, which corresponds to the z value of 0.06–0.13 by using the mixtures of the Si metal and α-Si3N4 powder. The photoluminescence of the samples showed the blue shifted emission spectrum and the narrower line width when the oxygen concentration was decreased. A wider color gamut can be achieved by using the β-sialon with the low oxygen concentration.
Physical and Analytical Electrochemistry
F9
L. T. T. Kim, C. Gabrielli, A. Pailleret and H. Perrot
Electrodeposited polypyrrole films doped with hexasulfonated calix[6]arenes are mainly cation exchangers during electrochemically induced doping/undoping processes in a 0,1 M KNO3 solution. This is shown here from ion concentrations variations and time constants extracted from ac-electrogravimetry experiments. EIS measurements show that diffusion of ions in the solution is not the rate limiting step in these processes. In parallel, electrochemical AFM investigations revealed correlated swelling/shrinking processes. Actually, ion exchanges imply predictable and fast electromechanical processes that are followed by much slower thickness variations in the opposite direction resulting possibly from conformational relaxation phenomena involving the polymeric chains.
Semiconductor Devices, Materials, and Processing
H431
Hyun Cho, E.A. Douglas, A. Scheurmann, B.P. Gila, V. Craciun, E.S. Lambers, E.S. Pearton and F. Ren
The use of Al2O3 as a gate dielectric has been shown to improve the performance and electrical stability of α-InGaZnO4 (IGZO) thin film transistors. X-ray photoelectron spectroscopy (XPS) was used to measure the energy discontinuity in the valence band (ΔEv) of Al2O3/IGZO heterostructures deposited by sputtering at <50°C, respectively. A value of ΔEv = 0.95 ± 0.17 eV was obtained by using the In 2p3/2, Zn 2p3/2 and 3d5/2 energy levels as references. Given the experimental bandgap of 3.2 eV for the IGZO, this would indicate a conduction band offset of 2.35 eV in this system.
H434
Tsung-Yen Tsai, Ray-Hua Horng, Dong-Sing Wuu, Sin-Liang Ou, Ming-Tsung Hung and Hsu-Hung Hsueh
GaN-on-sapphire structure with a Ga2O3 sacrificial layer was employed for the chemical lift-off process application. The (
01) β-oriented Ga2O3 thin film was first deposited on the c-plane sapphire substrate using pulsed laser deposition, followed by the GaN growth via metalorganic vapor phase epitaxy under N2 and H2 environment in sequence. From the transmission-electron-microscopy observation, the orientation relationship between GaN and β-Ga2O3 was identified as GaN[11
0]∥Ga2O3[010]. A GaN epilayer with an electroplated copper substrate was demonstrated using a chemical lift-off process where the Ga2O3 sacrificial layer can be laterally etched out with a hydrofluoric solution.
H438
Shuangyu Xin, Yuhua Wang, Zhaofeng Wang, Feng Zhang, Yan Wen and Ge Zhu
Eu3+ doped YBa3(PO4)3 series were successfully synthesized by conventional solid state reaction and their luminescence properties were investigated. The excitation spectra suggested that YBa3(PO4)3:xEu3+ presented a strong absorption in near-ultraviolet region. Under 393 nm excitation, YBa3(PO4)3:xEu3+ exhibited an intense red emission and the optimum concentration of Eu3+ was determined to be around 40%. Comparing with the red phosphor Y2O3:Eu3+, Y0.6Ba3(PO4)3:0.4Eu3+ has higher emission intensity and better color purity, which indicated that YBa3(PO4)3:xEu3+ could be potentially applied in near ultraviolet light emitting diodes.
H442
Seung-Yeol Han and Chih-hung Chang
The effect of annealing environment on indium zinc oxide (IZO) TFT performance was evaluated. With a focus on lower temperature processing, the influence of air and O2/O3 ambient conditions was directly compared. Field effect mobilities for IZO TFTs annealed at 300 and 500°C in air resulted in mobility values of 0.03 and 6.06 cm2/V·s, respectively. The IZO TFTs annealed in an O2/O3 atmosphere at 300°C resulted in a field effect mobility of 0.94 cm2/V·s, which is 30 times higher than mobility of the device annealed at the same temperature in an air atmosphere.
H446
Byung Oh Jung, Dong Chan Kim, Bo Hyun Kong, Ju Ho Lee, Jeong Yong Lee and Hyung Koun Cho
Transparent indium tin oxide (ITO) was directly deposited by magnetron sputtering to form two-dimensional top electrodes on vertically arrayed one-dimensional ZnO nanowires. Deposition at 5 mTorr resulted in almost complete coverage and interconnection of the nanowires, which maintained high transmittance. The use of lower pressure reduced ITO coverage over large areas of the nanowires due to the retardation of lateral coalescence. The sputtered ITO layers did not cover the entire lengths of the ZnO nanowires, although thin ITO coating was observed along the sidewalls of the nanowires for some distance from the surface. The ITO layers on the nanowire arrays had high conductivity, comparable to conventional In metal, because of the use of a plasma atmosphere and high temperature during deposition. This resulted in improved Ohmic contact and photodiode properties, which allowed direct electrical connection of the active nanowires without filling the spaces between them with insulating materials.
H450
Jong-Young Cho, Hao Cui, Jin-Hyung Park, Hyung-Soon Park and Jea-Gun Park
The corrosion inhibition effect of different nonionic polymers, which are polyacrylamide (PAM), polyvinyl pyrrolidone (PVP), and polyvinyl alcohol (PVA), on polycrystalline Ge2Sb2Te5 (pc-GST) was investigated in an alkaline media for chemical mechanical planarization. The adsorption affinity and inhibition effect of nonionic polymers on pitting corrosion were observed using x-ray photoelectron spectroscopy and a potentiodynamic polarization curve, respectively. We found that PVP was more effective than the others in inhibiting the pitting corrosion of pc-GST film in the alkaline media.
H453
Ray-Hua Horng, Re-Ching Lin, Hung-Lieh Hu, Kun-Cheng Peng and Chen-Peng Hsu
In this study, composite electroplating technique is used to fabricate the diamond-added copper (DAC) heat spreader for UV LED applications. Thermal dissipation characteristic and optical performance are improved as the composite DAC heat spreader adoption. The low thermal resistance of 18.4 K/W with UV LED using DAC heat spreader was measured. Surface temperature of UV LED using the DAC heat spreader is 45.32°C (at 350 mA injecting current), which is lower than those of LEDs using pure copper heat spreader (50.11oC) and only sapphire substrate (62.49°C). The thermal diffusivity of the DAC is 0.7179 cm2/s measurement by laser flash method. Output power and power efficiency of UV LEDs are also enhanced to 71.81 mW and 4.32%, respectively, at 350 mA injection current. The optimal structure design and materials fabrication will be discussed.
H457
A. Canino, M. Camarda and F. La Via
We present a characterization technique to assess the quality of 4H-SiC CVD growth process based on optical methods. The setup allows characterizing the epilayer and the substrate at the same time, leading to a self-consistent determination of the epitaxial layer quality with respect to the substrate. By using high power density UV optical pumping to stress 4H-SiC epitaxial layers, we are able to check the generation and evolution of Single Shockley faults on large areas, without fabricating bipolar junctions. This characterization technique is a fast and non-destructive method to compare the quality of different 4H-SiC CVD growth process.
H460
Surani Bin Dolmanan, Siew Lang Teo, Vivian Kaixin Lin, Hui Kim Hui, Armin Dadgar, Alois Krost and Sudhiranjan Tripathy
Thin-film InGaN/GaN multiple-quantum-well light emitting diodes (LEDs) are successfully fabricated on copper using a layer transfer technique from nitride layers epitaxially grown on silicon-on-insulator substrates. The layer transfer process includes p-contact metal deposition, metal electroplating, a substrate removal process, and top n-contact formation on LED chips. The thickness of nitride layers in such vertical LED chips after dry etching of n-GaN is about 700–800 nm. The emission intensity from electroluminescence (EL) measurements shows an increasing trend with drive current. Furthermore, using this route of a silicon-substrate based approach, the authors demonstrated vertical green LED chips with photonic crystal structure on top n-GaN layer resulting in enhanced EL performances.
H464
E. A. Douglas, S. J. Pearton, B. Poling, G. D. Via, L. Liu and F. Ren
Sub-micron gate length AlGaN/GaN high electron mobility transistors were electrically stressed at 10 GHz at various drain bias conditions under 3 dB compression. The output power and drain current degradation was minimal up to drain bias of 20 V. Rapid degradation was observed at a threshold drain bias of 25 V. While most RF and DC device characteristics exhibited negligible change up to 20 V drain bias conditions, the Ni/Au Schottky contact showed considerable degradation at all drain bias conditions with an increase in gate leakage current, threshold voltage and Schottky barrier height.
H467
C.L. Yang, C.I. Li, G.P. Lin, I.M. Lai, R. Liu, H.Y. Wang, B.C. Hsu, M. Chan, J.Y. Wu, B.N. Guo et al
SiGe/Si hetero structure has been examined using high resolution x-ray diffraction for strain and cross sectional transmission electron microscopy for implant induced defects with various p-type source drain implant conditions at room or cryogenic temperature. The implant induced end-of-range defects can be reduced by optimizing Ge pre-amorphization implant energy and at cryogenic temperature. The alleviated strain relaxation and lower junction leakage current are correlated to the cryo-implant defect reduction.
H470
J. Fan, D. F. Lim, L. Peng, K. H. Li and C. S. Tan
Low temperature (250–300°C) Cu-Cu thermocompression bonding for hermetic sealing application is investigated in this work. Cavities are etched to a volume of 1.4 × 10−3 cm3 on one group of wafers in accordance with the MIL-STD-883E standard prescribed for microelectronics packaging. The wafer pairs (non-functional cavity wafer and cap wafer) are bonded at 250 and 300°C, respectively, under a bonding force of 5500N for a duration of 1 hr. The bonding medium consists of Cu (300 nm) bonding layer and Ti (50 nm) barrier layer. The cavities are encapsulated by different seal ring size and different seal ring structure. Helium over-pressure in a bombing chamber and helium leak rate detection by a mass spectrometer are used for hermeticity measurement. The measurement results show that the cavities encapsulated at 250 and 300°C exhibit sufficient hermeticity for sealing application. Double-ring structure is found to outperform single-ring structure. Excellent helium leak rates which are smaller than 5.0 × 10−9 atm.cm3/sec are detected on all the samples. These values are at least 10 times smaller than the reject limit defined by the MIL-STD-883E standard.
Sensors and Displays: Principles, Materials, and Processing
J73
Lili Han, Yuhua Wang, Huijuan Zhang and Jia Zhang
Ce3+/Eu3+ codoped GdAl3(BO3)4 phosphors were synthesized by a wet-chemical method, and their luminescence properties under ultraviolet (UV) and vacuum ultraviolet (VUV) excitation were investigated. Upon excitation both by UV and VUV light, the GdAl3(BO3)4: Eu3+ phosphors show intense emissions at 588, 613, 650 and 693 nm, which are associated with the typical 5D0-7FJ (J = 1–4) transitions of Eu3+, respectively. The presence of Ce3+ results in an enhancement of Eu3+ emission intensity, especially the red 5D0-7F2 transition at 613 nm of Eu3+ upon UV excitation, indicating that energy transfer happens from Ce3+ to Eu3+ in these phosphors.
J76
Hongwu Zhang, Chao-Nan Xu, Nao Terasaki and Hiroshi Yamada
Blue emission from CaYAl3O7:Ce(CYACe) excited by thermal, electronic and mechanical energy is reported in this letter. This finding may be applied as a guide in designing self-power optical sensors with direct applications inpharmacology, in situ biomedical monitoring and diagnostics. The results revealed that the emission bands of afterglow (AG), electroluminescence (EL) and mechanoluminescence (ML) are similar, located at 421 nm, which indicated that all the emissions are emitted from the same center of Ce3+. Furthermore, we can explain the electro-mechano-optical luminescence of CYACe using a model of the excitation of trapped electrons released by different energy sources
Nanostructured Materials, Carbon Nanotubes, and Fullerenes
K63
Yusaku Nishimura, Toshiyuki Nohira, Yousuke Mizutani and Rika Hagiwara
This paper reports a simple Si nanowire (SiNW) production process based on zinc-thermal reduction of SiCl4 in a sealed Pyrex® tube at 773 K. SiNWs with a diameter of about 300 nm were produced without any catalysts. The SiNWs consisted mainly of an amorphous phase, but also including a minor microcrystalline component. The introduction of Au nanoparticles to the reaction tube wall facilitated crystallization and resulted in the growth of thinner SiNWs. The typical diameter of these SiNWs was 10–20 nm. The simple apparatus and low operating temperature of this new process are advantageous in producing SiNWs on both industrial and laboratory scales.
Miscellaneous
S9
The following article is Free article
Andy Y. Lin and Paul C. McIntyre